... in order to handle musb's clock. Let's start
removing the old musb-only set_clock function.
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
eps_bits wasn't being used anywhere, let's remove it.
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pass board specific data for MUSB (like interface_type,
mode etc) from board file by defining board
specific structure.
Each board file can define this structure based on
its requirement and pass this information to the
driver.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Gupta Ajay Kumar <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap3430 TRM says the OTG address space is 4k, not 8k.
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes #ifdef around usb_nop_xceiv_register()
from board-omap3evm.c
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the omap3_evm_defconfig to
select these options:
* CONFIG_PM_DEBUG
* CONFIG_DEBUG_FS
* CONFIG_OMAP_SMARTREFLEX
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds a default config for the Timll Devkit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These patches add board support for the Timll DevKit8000.
The DevKit8000 is a beagle board clone from Timll, sold by
armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D,
S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and
JTAG interface.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform hook-up interface to support I2C based GPIo expander
(TCA6416).
There are 3 instances of I2C Expander on AM3517EVM,
- One is over I2C-2 mounted on Base board
- Two are over I2C3 mounted on UI Card
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add basic I2C board Hook-up support, where all the 3 I2C instances
are getting registered.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If not configured it will be exported as normal GPIO led.
Signed-off-by: Jonas Zetterberg <jozz@jozz.se>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enabled VMMC2 LDO voltage regulator on TWL4030.
Added GPIO's (power down and reset) for WIFI chip.
Signed-off-by: Anders Hedlund <anders.j.hedlund@gmail.com>
Signed-off-by: Jonas Zetterberg <jozz@jozz.se>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It appears the wrong GPIO registers were used
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Currently <asm/mach/irq.h> is included by core.c. This header
includes <linux/irq.h> and defines a number of internal functions.
These internal functions are not needed by this file. Change the
include so that we just get what is needed.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 'outer_cache' variable is needed by the outer_inv_range(),
outer_clean_range() and outer_flush_range() functions, which are
declared as inline in asm/cacheflush.h. Otherwise drivers built
as a loadable module, which access these functions, will have
an undefined symbol.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The system to allow panel drivers to exists as attached to ctrl drivers
did never work very well. It is not useed, and this patch removes it to
make the driver cleaner.
For now, controller drivers need to include also the panel driver code. In
the future a proper mechanism for this should be developed, perhaps by
creating busses for controllers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add timing data for the Numonyx M65KxxxxAM SDRAM chip, used on the
IGEP v2 board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for flashes on IGEP v2 boards. For now
only OneNAND is supported.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform init code for EHCI driver on IGEP v2
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform data for the twl4030_codec MFD on IGEP v2
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable DSS2 and update defconfig for current kernel.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update pandora's regulator setup:
- add new regulators: VAUX2, VAUX4 and VSIM
- add new consumers: ads7846, nub controllers, USB PHY, audio DAC
- use dev names instead of struct device pointers
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds configuration data for DSS2 and sets up
display related regulators.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO175 is used for PEN_IRQ on the EVM. This patch
sets the mux settings for the same.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The keypad was not working properly after migrating
to matrix_keypad.
Swapped the row, col fields of the KEY() macro in
the keymap definition to get it working again.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch sets SYS_NIRQ for keypad input. It also
sets the same as a wakeup event from OFF mode.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Zoom3 board has omap3630 EHCI port2 connected to a ULPI phy.
GPIO_64 is connected to the PHY reset pin.
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The check for a valid mux name should be performed regardless of whether
DEBUG_FS is enabled or not. Otherwise without DEBUG_FS, we get:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1]
last sysfs file:
Modules linked in:
CPU: 0 Not tainted (2.6.33-rc8 #10)
PC is at strcmp+0x18/0x40
LR is at omap_mux_init_signal+0x68/0x14c
...
This fixes the issue currently seen with boards not booting up
if DEBUG_FS is not enabled in defconfig.
Note that the earlier ifndef + ifdef now becomes simpler ifdef else:
If CONFIG_OMAP_MUX is selected, we use pin names. If it's not selected,
we only want the GPIO to mux register mapping.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Makes it consistent with VMALLOC_START
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds DMA area to 'virtual memory map' startup message
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Code based on parisc and x86_32.
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch enables L2 cache and associated Errata on the
OMAP4430 SDP.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch implements the work-around for the errata 588369.The secure
API is used to alter L2 debug register because of trust-zone.
This version updated with comments from Russell and Catalin and
generated against 2.6.33-rc6 mainline kernel. Detail
comments can be found:
http://www.spinics.net/lists/linux-omap/msg23431.html
Signed-off-by: Woodruff Richard <r-woodruff2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds L2 Cache support for OMAP4. External L2 cache
is used in OMAP4
CC: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the cache maintainance by line helper functions.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If we're only reading the VFP context via the ptrace call, there's
no need to invalidate the hardware context - we only need to do that
on PTRACE_SETVFPREGS. This allows more efficient monitoring of a
traced task.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The more I look at vfp_sync_state(), the more I believe it's trying
to do its job in a really obscure way.
Essentially, last_VFP_context[] tracks who owns the state in the VFP
hardware. If last_VFP_context[] is the context for the thread which
we're interested in, then the VFP hardware has context which is not
saved in the software state - so we need to bring the software state
up to date.
If last_VFP_context[] is for some other thread, we really don't care
what state the VFP hardware is in; it doesn't contain any information
pertinent to the thread we're trying to deal with - so don't touch
the hardware.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The generic ptrace_request() handles these for us, so there's no
need to duplicate them in arch code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Recognize 0xf7f0 0xa000 as a 32-bit breakpoint instruction for
Thumb-2.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Otherwise the kernel built with both CPU_V6 and CPU_V7 will not
boot on omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current ASID allocation algorithm doesn't ensure the notification
of the other CPUs when the ASID rolls over. This may lead to two
processes using the same ASID (but different generation) or multiple
threads of the same process using different ASIDs.
This patch adds the broadcasting of the ASID rollover event to the
other CPUs. To avoid a race on multiple CPUs modifying "cpu_last_asid"
during the handling of the broadcast, the ASID numbering now starts at
"smp_processor_id() + 1". At rollover, the cpu_last_asid will be set
to NR_CPUS.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/of/fdt expects a cmd_line symbol, while arm uses command_line.
Change to the former, so that we can eventually share with the fdt
code.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On ARMv7, the use of the cp15 operations for barriers is deprecated
in favour of the isb, dsb, and dmb instructions. Change the locking
functions to use the appropriate type of dsb for the architecture
being built for.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In preparation for perf-events support, ARM needs to support atomic64_t
operations. v6k and above support the ldrexd and strexd instructions to
do just that.
This patch adds atomic64 support to the ARM architecture. v6k and above
make use of new instructions whilst older cores fall back on the generic
solution using spinlocks. If and when v7-M cores are supported by Linux,
they will need to fall back on the spinlock implementation too.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kernel debuggers want to be informed of die() events, so that they
can take some action to allow the problem to be inspected. Provide
the hook in a similar manner to x86.
Note that we currently don't implement the individual trap hooks.
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM setup code includes its own parser for early params, there's
also one in the generic init code.
This patch removes __early_init (and related code) from
arch/arm/kernel/setup.c, and changes users to the generic early_init
macro instead.
The generic macro takes a char * argument, rather than char **, so we
need to update the parser functions a little.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Always creating this directory avoids other users having to jump
through silly hoops when they want to share this directory.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All RTC drivers have been converted to rtclib, so the old code
providing the set_rtc function pointer, save_time_delta() and
restore_time_delta() functions is obsolete. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows the procfs vmallocinfo file to show who created the ioremap
regions. Note: __builtin_return_address(0) doesn't do what's expected
if its used in an inline function, so we leave __arm_ioremap callers
in such places alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for Bluewater Systems EP9315 based Snapper CL15 single board
computer module.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Hartley Sweeten <hartleys@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add platform device for McPDM interface in OMAP4 and register
its memory and irq resources.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define McPDM physical and L3 base address for OMAP4
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
sdp4430_uart_config isn't used anywhere, so remove it.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3517/05 has few additional control module registers to control
the new IP's, like VPFE, USBOTG, CPGMAC.
This patch adds the bit defination for INTR_CLR and SW_RST control
register.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add base address definations for new AM35xx IPSS modules, like
VPFE, USBOTG, CPGMAC.
Please note that the OMAP34xx IVA2 memory space is being used for
AM35xx IPSS modules.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Changes for setting the padconf value for sys_nirq line which is
connected to T2 INTR1. This will fix the T2 keypad wakeup.
Signed-off-by: Lesly A M <x0080970@ti.com>
Signed-off-by: Teerth Reddy <teerth@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Get rid of the ifdeffery in omap_mux_init by creating
omap_mux_init_package and omap_mux_init_signals functions.
Signed-off-by: Tony Lindgren <tony@atomide.com>
EMMC can have two voltage supplies, Vcc and VccQ
which are implemented in the code as consumer
supplies vmmc and vmmc_aux.
If the regulator that supplies vmmc_aux is shared
with other consumers, then sending it to sleep
will disrupt those consumers. However, the
TWL4030-family regulators may have OFF remapped
to SLEEP, in which case 'regulator_disable()'
will put the regulator to sleep only when all
consumers are disabled - which is the desired
behaviour.
This patch adds a platform data field to allow
that option.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An eMMC may be always powered on, so that the lowest
power saving state possible is sleeping. Add a field
to the platform data to indicate that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It has been discovered that, when eMMC is powered off, current
will flow from OMAP eMMC data pull-ups to the eMMC voltage supply.
Configuring pads for OMAP off-mode does not help because eMMC is
powered off independently of OMAP off-mode. Hence the pads are
now re-configured when eMMC is powered on or off.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Call the PM context-loss count function, now that there
is a prototype for it.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
hsmmc.[ch] no longer has any dependency on twl4030
and variable names should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mmc-twl4030.[ch] no longer has any dependency on twl4030
and should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves the setup code for GPIO's and Voltage
Regulators from the board file mmc-twl4030.c to the
driver omap_hsmmc.c. PBIAS and other system control
configuration remains in the board file.
Moving GPIO code to the driver makes the board initialisation
code independent of when GPIO's are defined. That makes the
board initialisation now entirely independent of its original
twl4030 roots.
Moving Voltage Regulator code to the driver allows for further
development of regulator support in the core MMC code. It also
permits the MMC core to be compiled as a module, because the
board code no longer calls MMC core functions.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for flashes on 3430SDP boards. All three
NAND, NOR and OneNAND are supported. I have tested it on
3430SDP (ES2 and ES3.1).
This patch can be treated as an example to "how to utilize":
'gpmc-nand.c' and 'board-sdp-flash.c'.
Similar patches can be created for 2430sdp and 3630sdp or any other
similar board.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds 'board-sdp-flash.c', which could be utilized
by boards similar to 3430SDP. (For ex: 2430sdp, 36030sdp).
This file does initialization for all three flash devices present
in SDP boards (NOR, NAND, OneNAND), by finding there 'cs' number
dynamically using switch setting information (S8: 1-4).
This also expects partition information from core board files (for
ex: board-3430sdp.c). Which allows to choose different default
partitions for different boards.
A new structure is created for this purpose: 'flash_partitions'
in 'mach/board-sdp.h'. This has two members:
1. struct mtd_partition *parts
2. int nr_parts
A board file is expected to fill this structure and pass it to
'sdp-flsash-init'. Partition information should be passed in
structure array of 'flash_partitions'. Partition information should
be passed in below sequence in array:
NOR
OneNAND
NAND
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introducing 'gpmc-nand.c' for GPMC specific NAND init.
For example: GPMC timing parameters and all.
This patch also migrates gpmc related calls from 'nand/omap2.c'
to 'gpmc-nand.c'.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Get rid of the following warnings:
arch/arm/mach-omap2/gpmc.c:550:30: warning: non-ANSI
function declaration of function 'omap3_gpmc_save_context'
arch/arm/mach-omap2/gpmc.c:581:33: warning: non-ANSI
function declaration of function 'omap3_gpmc_restore_context'
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
use ioremap and remove unused variable to get rid
of compile warnings.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change the way McBSP registers are updated: use cached values instead of
relying upon those read back from the device.
With this patch, I have finally managed to get rid of all random
playback/recording hangups on my OMAP1510 based Amstrad Delta hardware. Before
that, values read back from McBSP registers to be used for updating them
happened to be errornous.
From the hardware side, the issue appeared to be caused by a relatively high
power requirements of an external USB adapter connected to the board's printer
dedicated USB port.
I think there is one important point that makes this patch worth of applying,
apart from my hardware quality. With the current code, if it ever happens to
any machine, no matter if OMAP1510 or newer, to read incorrect value from a
McBSP register, this wrong value will get written back without any checking.
That can lead to hardware damage if, for example, an input pin is turned into
output as a result.
Applies on top of patch 3 from this series:
[PATCH v9 3/4] OMAP: McBSP: Introduce caching in register write operations
Tested on OMAP1510 based Amstrad Delta using linux-omap for-next, commit
fb7380d70e041e4b3892f6b19dff7efb609d15a4 (2.6.33-rc3+ dated 2010-01-11).
Compile-tested with omap_3430sdp_defconfig.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Determine cache size required per McBSP port at init time, based on
processor type running on.
Allocate space for storing cached copies of McBSP register values at
port request.
Modify omap_msbcp_write() function to update the cache with every
register write operation.
Modify omap_mcbsp_read() to support reading from cache or hardware.
Update MCBSP_READ() macro for modified omap_mcbsp_read() function API.
Introduce a new macro that reads from the cache.
Tested on OMAP1510 based Amstrad Delta using linux-omap for-next, commit
fb7380d70e041e4b3892f6b19dff7efb609d15a4 (2.6.33-rc3+ dated 2010-01-11).
Compile-tested with: omap_perseus2_730_defconfig, omap_generic_1610_defconfig,
omap_generic_2420_defconfig, omap_2430sdp_defconfig, omap_3430sdp_defconfig,
omap_4430sdp_defconfig with CONFIG_OMAP_MCBSP=y selected.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_MCBSP_READ()/_WRITE() macros and omap_mcbsp_read()/_write() functions
accept McBSP register base address as an argument. In order to support
caching, that must be replaced with an address of the omap_mcbsp structure
that would provide addresses for both register AND cache access.
Since OMAP_ prefix seems obvious in macro names, drop it off in order to
minimize line wrapping throughout the file.
Tested on OMAP1510 based Amstrad Delta using linux-omap for-next, commit
fb7380d70e041e4b3892f6b19dff7efb609d15a4 (2.6.33-rc3+ dated 2010-01-11).
Compile-tested with omap_3430sdp_defconfig.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are several places where readw()/writew() functions are used instead of
OMAP_MCBSP_READ()/WRITE() macros for manipulating McBSP registers. Replace
them with macros to ensure consistent behaviour after caching is introduced.
Tested on OMAP1510 based Amstrad Delta.
Compile-tested with omap_3430sdp_defconfig.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There was a potential risk that the following "memset" could override
its range if a given address was not the 1st entry of a
largepage. This is not the case for "iovmm".
Reported-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There was a potential risk that the following "memset" could override
its range if a given address was not the 1st entry of a
supersection. This is not the case for "iovmm".
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is just a cleanup, but adds a few macros here, which can be used
in the proceeding patches.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert OMAP based boards to use physmap-flash. Refreshed against today's
Linux omap kernel tree
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add omap4 into omap3_defconfig. Note that this does not
yet boot on omap4, but boots on omap2 and omap3.
Also note that CONFIG_SMP does not currently work on
uniprocessor ARMs.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Set up METHOD_GPIO_44XX instead of trying to use the METHOD_GPIO_24XX.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename clkops_noncore_dpll_ops for omap3 and omap4.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow booting omap4 with multi-omap configuration.
Tested only on omap2 and omap3, please somebody test
on omap4 and ack.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move defines around and set up handlers based on MULTI_OMAP2.
Note that this will only allow compiling in omap4 with omap2 and
omap3. It will not yet make omap4 boot with multi-omap.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define the irq base the same way as for omap2 and omap3,
and start using get_irqnr_preamble.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we can include it easily as needed also for .S files.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Note that booting 2420 depends on another patch posted earlier to not
select CONFIG_CPU_32v6K if CONFIG_ARCH_OMAP2 is selected.
Also note that we cannot add omap2430 in yet because of the different
clock addresses compared to 2420. Also note that we cannot have
CONFIG_CPU_32v6K=y in order to boot on 24xx.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix dmtimer.c for multi-omap boot. Also remove legacy
clk_enable/disable wrappers that are no longer needed.
Note that the clock handling should be further improved
to make use of the clock aliases.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make get_irqnr_and_base common for mach-omap2 multiboot
Thanks to a tip from Russell King <rmk+kernel@arm.linux.org.uk>,
this also optimizes the code for non-multiboot configurations by
using get_irqnr_preamble.
Note that this will only work currently for 24xx and 34xx.
Support for 44xx can be added later on for basic multiboot,
and similar patch should be done for mach-omap1/entry-macro.S.
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are no longer needed. Note that zoom boards
should now set their own function in uncompress.h
and debug-macro.S for the external UART.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define arch_decomp_setup() the same way as some other
architectures do. Use arch_id to configure the debug uart
based on the machine_is by storing it into the uart
scratchpad register for DEBUG_LL code to use.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we don't have conflicts with the defines
with compiling in multiple omaps. Set the addresses
for uarts in struct omap_globals for the early serial
init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
ARMv6 and ARMv7 CPUs can perform speculative prefetching, which makes
DMA cache coherency handling slightly more interesting. Rather than
being able to rely upon the CPU not accessing the DMA buffer until DMA
has completed, we now must expect that the cache could be loaded with
possibly stale data from the DMA buffer.
Where DMA involves data being transferred to the device, we clean the
cache before handing it over for DMA, otherwise we invalidate the buffer
to get rid of potential writebacks. On DMA Completion, if data was
transferred from the device, we invalidate the buffer to get rid of
any stale speculative prefetches.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-By: Santosh Shilimkar <santosh.shilimkar@ti.com>
These are now unused, and so can be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-By: Santosh Shilimkar <santosh.shilimkar@ti.com>
dma_cache_maint_contiguous is now simple enough to live inside
dma_cache_maint_page, so move it there.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-By: Santosh Shilimkar <santosh.shilimkar@ti.com>
The DMA API has the notion of buffer ownership; make it explicit in the
ARM implementation of this API. This gives us a set of hooks to allow
us to deal with CPU cache issues arising from non-cache coherent DMA.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-By: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-By: Jamie Iles <jamie@jamieiles.com>
Rename and export dsi_vc_enable_hs() so that the display drivers can
control the mode of the DSI link.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
This fixes a few bugs in the DMA configuration for the COH 901 318
DMA engine used in U300. It also removes the directional parameter
for each channel: separate DMA engine patches (submitted to the
DMA engine maintainer) switches that mechanism over to using
dynamic configuration of this, to handle bidirectional DMA
channels.
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a static mapping for the UART and correct its virtual address in
debug-macro.S, to make DEBUG_LL/earlyprintk work.
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
mach/timex.h is only supposed to contain a definition for
CLOCK_TICK_RATE. Remove additional includes, and move private
definitions to a private header file.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
clk_set_rate() is not supposed to be used to turn clocks on and off.
That's what clk_enable/clk_disable is for.
Acked-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
clk_set_rate() is not supposed to be used to turn clocks on and off.
That's what clk_enable/clk_disable is for.
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most machine classes want some way to register a block of clk_lookup
structures, and most do it by implementing a clks_register() type
function which walks an array, or by open-coding a loop.
Consolidate all this into clkdev_add_table().
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds the Performance Events support for ARMv7 processor, using
the PMNC unit in HW.
Supports the following:
- Cortex-A8 and Cortex-A9 processors,
- dynamic detection of the number of available counters,
based on the PMCR value,
- runtime detection of the CPU arch (v6 or v7)
and model (Cortex-A8 or Cortex-A9)
Tested on OMAP3 (Cortex-A8) only.
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch implements support for ARMv6 performance counters in the
Linux performance events subsystem. ARMv6 architectures that have the
performance counters should enable HW_PERF_EVENTS to get hardware
performance events support in addition to the software events.
Note: only ARM Ltd ARM cores are supported.
This implementation also provides an ARM PMU abstraction layer to allow
ARMv7 and others to be supported in the future by adding new a
'struct arm_pmu'.
Cc: Jean Pihet <jpihet@mvista.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The perf events subsystem allows counting of both hardware and
software events. This patch implements the bare minimum for software
performance events.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make sure that we have access to the performance counters and
that they aren't being used by perf events or anything else.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To add support for perf events and to allow the hardware counters to be
shared with oprofile, we need a way to reserve access to the pmu
(performance monitor unit). Platforms with PMU interrupts should
register the interrupts in arch/arm/kernel/pmu.c
Signed-off-by: Jamie Iles <jamie.iles@picochip.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The regulator is now enabled by DSS driver, and thus the panel driver
doesn't need to touch it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The platform data allocated with kmalloc() will become unreachable once
the init is complete, so it should be freed. The problem was discovered
by kmemleak.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM cannot prevent cache movein, so this patch implements both the
flush and invalidate pieces of the API.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: Fix wrong register in proc-arm6_7.S data abort handler
ARM: 5909/1: ARM: Correct the FPSCR bits setting when raising exceptions
ARM: 5904/1: ARM: Always generate the IT instruction when compiling for Thumb-2
ARM: 5907/1: ARM: Fix the reset on the RealView PBX Development board
mx35: add a missing comma in a pad definition
mx25: make the FEC AHB clk secondary of the IPG
mx25: fix time accounting
mx25: properly initialize clocks
mx25: remove unused mx25_clocks_init() argument
i.MX25: implement secondary clocks for uarts and fec
i.MX25: Allow secondary clocks in DEFINE_CLOCK
ARM: MX3: Fixed typo in declared enum type name.
MXC: Add AUDMUXv2 register decode to debugfs
mx31ads: Provide an IRQ range to the WM835x on the 1133-EV1 module
mx31ads: Provide a name for EXPIO interrupt chip
mx31ads: Allow enable/disable of switchable supplies
Remove unneeded 'struct davinci_clk' wrapper around 'struct clk_lookup'
and use clkdev_add_table() to add the list of clocks in one go.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds the generic Voice Codec support for the DM365 based
platforms.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When supporting I2C/SPI based on-board PLLs like CDCE949,
it is essential that clk->set_rate be able to sleep.
Currently, this is not possible because clk->set_rate is
called from within spin-lock in clk_set_rate
This patch brings clk->set_rate outside of the spin-lock
and lets the individual set_rate implementations achieve
serialization through appropiate means.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Patch adds SDA and SCL pin numbers to the i2c platform data
structure for Davinci DM355 and DM6446. This at present is
used for i2c bus recovery.
TODO: Add SDA and SCL pin number information to include all
Davinci platforms such as dm355-leopard, dm365, dm646x, da8xx etc.
Signed-off-by: Philby John <pjohn@in.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently da850/omap-l138 supports only one channel controller
instance of EDMA though EDMA driver as such supports multiple
channel controller instances. This patch adds platform data
for the 2nd EDMA channel controller. As, the platform data
differ between da830/omap-l137 and da850/omap-l138, existing
code has been re-shuffled to accommodate this.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently, the edma_noevent list is passed from platform data.
But on some architectures, there will be many EDMA channels
which will not be used at all. This patch scans all the
platform devices and then builds a list of events which are
not being used. The unused event list will be used to allocate
EDMA channels in case of EDMA_CHANNEL_ANY usage instead of the
edma_noevent being used earlier for this purpose.
This patch is based on David Brownells's suggestion at
http://article.gmane.org/gmane.linux.davinci/15176.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Though edma_alloc_channel api was looping through the available
channel controllers in EDMA_CHANNEL_ANY case, it was never
returning the channel for 2nd channel controller, if 1st
channel controller had no free channels. This issue has
been fixed with this patch.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Some architectures have only one channel controller, but the
edma_alloc_channel api loops twice to findout the free channel
available in EDMA_CHANNEL_ANY case. A new variable has been
introduced to keep count of number of channel controllers being
used on a particular architecture.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently, edma_alloc_channel api is returning the channel
number without prepending the controller on which the
channel was allocated. So, if a channel is allocated on
2nd controller, calls subsequent to edma_alloc_channel would
never know that channel was allocated on the 2nd controller,
and continue to operate on 1st controller, resulting in edma
failure. This patch fixes this issue.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds the CDCE949 reference oscillator to
the davinci clock list.
On the DM6467T EVM, the CDCE949 is responsible for
generating the pixel clock for display. On the DM6467
EVM, this pixel clock was being obtained from an
internal source. This is not possible on the DM6467T
EVM because of the presence of a 33MHz oscillator.
The TSIF module also requires the CDCE949 to generate
the data clocks.
The actual clock definitions will be added by patches
adding support for DM6467T VPIF and TSIF. This patch
mearly lays the foundation for that work.
Signed-off-by: Nageswari Srinivasan <nageswari@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds support for TI's CDCE949 - a clock
synthesizer with 4 PLLs and 9 outputs.
It is used on DM6467 EVM. On the EVM, it generates
clocks required for VPIF, TSIF and Audio modules.
This patch adds it as part of the DaVinci clock framework.
Testing:
The various frequency outputs on Y1 have been tested using
a out-of-tree VPIF video driver supporting HD video.
The register values for Y5 frequency outputs have been
derived from TSIF driver sources in MontaVista LSP kernel,
but actual output has not been tested for lack of TSIF
driver which actually works on the latest kernel.
Signed-off-by: Nageswari Srinivasan <nageswari@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds support for registering for suspend-to-RAM
functionality on da850/omap-l138 SoCs.
da850 supports wakeup based on external event and RTC
alarm.
Currently only RTC alarm based wakeup is supported.
Support for wakeup based on external event will be
added as later improvements.
For scheduling an alarm event on RTC some useful code
is present in Documentation/rtc.txt
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds core power management (suspend-to-RAM)
support for DaVinci SoCs.
The code depends on the the "deepsleep" feature to suspend
the SoC and saves power by gating the input clock.
The wakeup can be based on an external event as supported
by the SoC.
Assembly code (in sleep.S) is added to aid gating DDR2
clocks. Code doing this work should not be accessing DDR2.
The assembly code is relocated to SRAM by the code in pm.c
The support has been validated on DA850/OMAP-L138 only
though the code is (hopefully) generic enough that other
SoCs supporting deepsleep feature simply requires SoC
specific code to start using this driver.
Note that all the device drivers don't support suspend/resume
still and are being worked on.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
In DM365 Q0, Q1 and Q2 are used by codecs.
LSP drivers should use Q3.
This patch changes the default queue for DM365.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Some modules do not have PSC to control their clocks.
The 'lpsc' field in the clk structure is 0 for such clocks.
In the clock disable function check for CLK PSC flag before
disabling the PSC. If this is not taken care of then it may
so happen that module controlled by LPSC 0 is erroneously disabled.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The davinci EMAC peripheral is also available on other TI
platforms -notably TI AM3517 SoC. This patch modifies the
config option and the platform structure header files so that
the driver can be reused on non-davinci platforms as well.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Acked-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch initializes the platform data to enable 4-bit
ecc support on DA850/OMAP-L138.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On DA850/OMAP-L138, NOR flash partition was starting from offset
ZERO erasing the UBL and u-boot when the complete NOR is erased.
This patch moves the start of the partition to 512K, after the
bootloaders and u-boot env variables.
This patch also creates a new partition on NOR Flash to store
Linux kernel image.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Move /proc/davinci_clocks to /sys/kernel/debug/davinci_clocks
(debugfs).
debugfs is more suited for this since the clock dump is
debug information.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies clock dump to take care of
clock tress rooted at multiple oscillators.
Current code assumes the entire tree is rooted
on a single oscillator. When using off-chip
clock synthesizers, some of the clocks can
be obtained from a different on-board oscillator.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DM6467T (T for Turbo) is a newer and faster DM6467
part from TI. The new part supports 1080p video and
has the ARM running at 495MHz. More SoC information:
http://focus.ti.com/docs/prod/folders/print/tms320dm6467t.html
Spectrum Digital, Inc has a new EVM for this part.
It is _mostly_ same as the older DM6467 EVM except
for a 33MHz crystal input and THS8200 video encoder
for 1080p support.
The meat of this patch is dedicated to initializing
the crystal frequency from EVM board file.
Additional notes:
I did consider some alternative ways to make the crystal
input board specific including - (1) having board code
initialize the crystal frequency using the first member
of soc_info->cpu_clks array (2) introducing a new ref_clk_rate
member in soc_info structure.
But, the current way seems to be the simplest and least
intruding considering that both the clock array and SoC
info structure are actually private to the SoC file. Also
the fact that davinci_common_init() initializes both the
soc_info and clocks in one go.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently all the #defines and static variables in the
board-dm646x-evm.c file are located right at the start
of the file because of which the related code is not
together - making reading the code difficult.
This patch moves around the code keeping related code
together.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Leave a comment explaining the constant value of 27Mhz used
in include/mach/timex.h for all DaVinci platforms. Many of
the platforms actually run at 24MHz timer frequency (Eg.
EVMs of DM355, DM365 and OMAP-L1).
The comment also serves as a porting alert.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Create static map for internal SRAM and populate SRAM base
and size in soc_info structure to allow SRAM allocation
functions from arch/arm/mach-davinci/sram.c to work.
On DA850 SRAM is used for suspend-to-RAM implementation
in places where DDR2 cannot be accessed as its clocks are
stopped.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On omap-l1 devices the PLL registers can be locked from
writes. Currently the cpufreq rate setting code unlocks
PLL0 before the write actually happens. With suspend
support getting added PLL1 registers need be be unlocked
as well.
To facilitate this, unlock both PLLs during the init time
itself.
This also obviates the need to unlock PLL registers for
each CPUFreq transtition.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When suspend is supported, both cpuidle and suspend code
need to work on DDR2 registers. Instead of mapping the
DDR2 registers twice, do it once outside of cpuidle
driver and let cpuidle driver get the virtual base address
of DDR2 registers.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
psc.h contains register defines for PSC module which
need to be accessed in assembly code which helps the
DA850/OMAP-L138 SoC go to sleep. Shutting down DDR clock
using PSC is a part of the sleep procedure.
Also, the PLL related hardware definitions in clock.h are
needed in assembly code to bypass the DDR2 PLL.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The motivation behind the change is to use the same
definitions in the assembly code responsible for
suspending the SoC, a part of which is to clock gate
the DDR2 clock.
Note that the assembly code cannot invoke the C function
meant for this. The main reason being that stack in DDR2
cannot be accessed while DDR2 clock is being clock gated.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Move defintions of DDR2 controller registers to memory.h
from cpuidle.c. The motivation behind the change is to be
able to use these defintions in assembly code that puts
DDR2 in self-refresh and enables the SoC to enter suspend
state.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
As suspend support is added, the code supporting
the suspend operation needs to bypass PLLs and
needs to access the same wait time values as the
PLL code in clock.c.
To facilitate this, move the PLL wait times to
clock.h where they can be accessed by suspend code.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP-L138 adds a second SYSCFG region having useful functionality
like deep sleep, pull up/down control and SATA clock stop.
This patch makes provision for accessing registers from second
SYSCFG region in da8xx code.
Note that OMAP-L137 has a single SYSCFG region.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds following changes:-
1) add sub device configuration data for TVP5146 used by vpfe capture
2) registers platform devices for vpfe_capture, isif and vpss
3) defines hardware resources for the devices listed under 2)
4) defines clock aliase for isif driver
5) adding setup_pinmux() for isif
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This adds platform configurations to support four
i2c controllers found on early MOP500 platform
This depends on the patch 5908/1 for build to succeed.
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds the platform specific i2c configuration
data structures to setup the nomadik/ux500 i2c block.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This configures the PL031 RTC resources for ux500.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently the omap serial clocks are autoidled after 5 seconds.
However, this causes lost characters on the serial ports. As this
is considered non-standard behaviour for Linux, disable the timeout.
Note that this will also cause blocking of any deeper omap sleep
states.
To enable the autoidling of the serial ports, do something like
this for each serial port:
# echo 5 > /sys/devices/platform/serial8250.0/sleep_timeout
# echo 5 > /sys/devices/platform/serial8250.1/sleep_timeout
...
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I have found an access to already released memory in
clk_debugfs_register_one() function.
Signed-off-by: Marek Skuczynski <mareksk7@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
David Binderman ran the sourceforge tool cppcheck over the source code of the
new Linux kernel 2.6.33-rc6:
[./arm/mach-omap2/mux.c:492]: (error) Buffer access out-of-bounds
13 characters + 1 digit + 1 zero byte is more than 14 characters.
Also add a comment on mode0 name length in case new omaps
start using longer names.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
3630 has more mux signals than 34xx. The additional pins
exist in omap36xx_cbp_subset, but are not initialized
as the superset is missing these offsets. This causes
the following errors during the boot:
mux: Unknown entry offset 0x236
mux: Unknown entry offset 0x22e
mux: Unknown entry offset 0x1ec
mux: Unknown entry offset 0x1ee
mux: Unknown entry offset 0x1f4
mux: Unknown entry offset 0x1f6
mux: Unknown entry offset 0x1f8
mux: Unknown entry offset 0x1fa
mux: Unknown entry offset 0x1fc
mux: Unknown entry offset 0x22a
mux: Unknown entry offset 0x226
mux: Unknown entry offset 0x230
mux: Unknown entry offset 0x22c
mux: Unknown entry offset 0x228
Fix this by adding the missing offsets to omap3 superset.
Note that additionally the uninitialized pins need to be
skipped on 34xx.
Based on an earlier patch by Allen Pais <allen.pais@ti.com>.
Reported-by: Allen Pais <allen.pais@ti.com>
Signed-off-by: Allen Pais <allen.pais@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ensure valid clock pointer during GPMC init. Fixes compiler
warning about potential use of uninitialized variable.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Ensure valid base address during IRQ init. Fixes compiler warning
about potential use of uninitialized variable.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP platforms(like OMAP3530) include DSP or other co-processors
for media acceleration. when carving out memory for the
accelerators we can end up creating a hole in the memory map
of sort:
<kernel memory><hole(memory for accelerator)><kernel memory>
To handle such a memory configuration ARCH_HAS_HOLES_MEMORYMODEL
has to be enabled. For further information refer discussion at:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg15262.html.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
