Add module parameters for the addresses to be used in B2B topology.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Reset the link stats when the link goes down. In particular, the TX and
RX index and count must be reset, or else the TX side will be sending
packets to the RX side where the RX side is not expecting them. Reset
all the stats, to be consistent.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
On link down, don't advance RX index to the next entry. The next entry
should never be valid after receiving the link down flag.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The same message "qp %d: Link Down\n" was printed at two locations in
ntb_transport. Change the messages so they are distinct.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Set errata flags for the specific device IDs to which they apply,
instead of the whole Xeon hardware class.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Link training should be enabled in the driver probe for root port mode.
We should not have to wait for transport to be loaded for this to
happen. Otherwise the ntb device will not show up on the transparent
bridge side of the link.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The transport was writing and then reading the peer scratch pad,
essentially reading what it just wrote instead of exchanging any
information with the peer. The transport expects the peer values to be
the same as the local values, so this issue was not obvious.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Change ntb_hw_intel to use the new NTB hardware abstraction layer.
Split ntb_transport into its own driver. Change it to use the new NTB
hardware abstraction layer.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Abstract the NTB device behind a programming interface, so that it can
support different hardware and client drivers.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This patch only moves files to their new locations, before applying the
next two patches adding the NTB Abstraction layer. Splitting this patch
from the next is intended make distinct which code is changed only due
to moving the files, versus which are substantial code changes in adding
the NTB Abstraction layer.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
- New driver for Microchip TC74
- Support for ncpXXwf104 added to ntc_thermistor driver
- Minor cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ZKHZ
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for Microchip TC74
- support for ncpXXwf104 added to ntc_thermistor driver
- minor cleanup
* tag 'hwmon-for-linus-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: add driver for Microchip TC74
hwmon: (ntc_thermistor) Improve precision of resistance calculation
hwmon: (ntc_thermistor) fix iio raw to microvolts conversion
hwmon: (atxp1) Drop auto-detection
hwmon: (atxp1) Drop FSF mailing address
hwmon: Allow compile test of GPIO consumers if !GPIOLIB
hwmon: (sht15) Constify platform_device_id
hwmon: (max197) Constify platform_device_id
hwmon: (ntc_thermistor) Add support for ncpXXwf104
- Fix an error path in the mmc block layer
- Fix PM domain attachment for the SDIO bus
- Add support for driver strength selection
- Increase a delay to let voltage stabilize
- Add support for disabling write-protect detection
- Add facility to support re-tuning
- Re-tune and retry in the recovery path
- Add reset option for SDIO
- Consolidations and clean-ups
MMC host:
- Add Mediatek MMC driver
- Constify platform_device_id for a couple of hosts
- Fix modalias to make module auto-loading work for a couple of hosts
- sdhci: Add support for sdhci-arasan4.9a
- sdhci: Fix low memory corruption
- sdhci: Restore behavior while creating OCR mask
- sdhci: Add a callback to select drive strength
- sdhci: Fix driver type B and D handling
- sdhci: Add support for drive strength selection for SPT
- sdhci: Enable HS400 for some Intel host controllers
- sdhci: Convert to use the new re-tuning facility
- sdhci: Various minor fixes and clean-ups
- dw_mmc: Add support for hi6220
- dw_mmc: Use core to handle absent write protect line
- dw_mmc: Add support to switch voltage
- tmio: Some fixes and modernizations
- sh_mmcif: Improve clock rate calculation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ofUZ
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.2' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"Here are the changes for MMC for v4.2.
MMC core:
- Fix an error path in the mmc block layer
- Fix PM domain attachment for the SDIO bus
- Add support for driver strength selection
- Increase a delay to let voltage stabilize
- Add support for disabling write-protect detection
- Add facility to support re-tuning
- Re-tune and retry in the recovery path
- Add reset option for SDIO
- Consolidations and clean-ups
MMC host:
- Add Mediatek MMC driver
- Constify platform_device_id for a couple of hosts
- Fix modalias to make module auto-loading work for a couple of hosts
- sdhci: Add support for sdhci-arasan4.9a
- sdhci: Fix low memory corruption
- sdhci: Restore behavior while creating OCR mask
- sdhci: Add a callback to select drive strength
- sdhci: Fix driver type B and D handling
- sdhci: Add support for drive strength selection for SPT
- sdhci: Enable HS400 for some Intel host controllers
- sdhci: Convert to use the new re-tuning facility
- sdhci: Various minor fixes and clean-ups
- dw_mmc: Add support for hi6220
- dw_mmc: Use core to handle absent write protect line
- dw_mmc: Add support to switch voltage
- tmio: Some fixes and modernizations
- sh_mmcif: Improve clock rate calculation"
* tag 'mmc-v4.2' of git://git.linaro.org/people/ulf.hansson/mmc: (98 commits)
mmc: queue: prevent soft lockups on PREEMPT=n
mmc: mediatek: Add PM support for MMC driver
mmc: mediatek: Add Mediatek MMC driver
mmc: dt-bindings: add Mediatek MMC bindings
mmc: card: Fixup request missing in mmc_blk_issue_rw_rq
mmc: sdhci: fix low memory corruption
mmc: sdhci-pci: Change AMD SDHCI quirk application scope
i2c-piix4: Use Macro for AMD CZ SMBus device ID
pci_ids: Add AMD KERNCZ device ID support
mmc: queue: use swap() in mmc_queue_thread()
mmc: dw_mmc: insmod followed by rmmod will hung for eMMC
mmc: sdhci: Restore behavior while creating OCR mask
mmc: sdhci-pxav3: fix device wakeup initialization
mmc: core: Attach PM domain prior probing of SDIO func driver
mmc: core: Remove redundant ->power_restore() callback for SD
mmc: core: Remove redundant ->power_restore() callback for MMC
mmc: sdhci-bcm2835: Actually enable the clock
mmc: sdhci-bcm2835: Clean up platform allocations if sdhci init fails.
mmc: sdhci-of-esdhc: enable interrupt mode to detect card
mmc: sdhci-esdhc-imx: add quirk SDHCI_QUIRK2_BROKEN_HS200 for imx6qdl
...
kernel series:
- A big set of cleanups to the aged sysfs interface from
Johan Hovold. To get these in, v4.1-rc3 was merged into
the tree as the first patch in that series had to go
into stable. This makes the locking much more fine-grained
(get rid of the "big GPIO lock(s)" and store states in the
GPIO descriptors.
- Rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value()
to avoid confusions.
- New drivers for:
- NXP LPC18xx (currently LPC1850)
- NetLogic XLP
- Broadcom STB SoC's
- Axis ETRAXFS
- Zynq Ultrascale+ (subdriver)
- ACPI:
- Make it possible to retrieve GpioInt resources from
a GPIO device using acpi_dev_gpio_irq_get()
- Merge some dependent I2C changes exploiting this.
- Support the ARM X-Gene GPIO standby driver.
- Make it possible for the generic GPIO driver to read
back the value set registers to reflect current
status.
- Loads of OMAP IRQ handling fixes.
- Incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.
- Janitorial (contification, checkpatch cleanups)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vKYs
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio updates from Linus Walleij:
"This is the big bulk of GPIO changes queued for the v4.2 kernel
series:
- a big set of cleanups to the aged sysfs interface from Johan
Hovold. To get these in, v4.1-rc3 was merged into the tree as the
first patch in that series had to go into stable. This makes the
locking much more fine-grained (get rid of the "big GPIO lock(s)"
and store states in the GPIO descriptors.
- rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value() to
avoid confusions.
- New drivers for:
* NXP LPC18xx (currently LPC1850)
* NetLogic XLP
* Broadcom STB SoC's
* Axis ETRAXFS
* Zynq Ultrascale+ (subdriver)
- ACPI:
* make it possible to retrieve GpioInt resources from a GPIO
device using acpi_dev_gpio_irq_get()
* merge some dependent I2C changes exploiting this.
* support the ARM X-Gene GPIO standby driver.
- make it possible for the generic GPIO driver to read back the value
set registers to reflect current status.
- loads of OMAP IRQ handling fixes.
- incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.
- janitorial (constification, checkpatch cleanups)"
* tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: Fix checkpatch.pl issues
gpio: pcf857x: handle only enabled irqs
gpio / ACPI: Return -EPROBE_DEFER if the gpiochip was not found
GPIO / ACPI: export acpi_gpiochip_request(free)_interrupts for module use
gpio: improve error reporting on own descriptors
gpio: promote own request failure to pr_err()
gpio: Added support to Zynq Ultrascale+ MPSoC
gpio: add ETRAXFS GPIO driver
fix documentation after renaming gpiod_set_array to gpiod_set_array_value
gpio: Add GPIO support for Broadcom STB SoCs
gpio: xgene: add ACPI support for APM X-Gene GPIO standby driver
gpio: tb10x: Drop unneeded free_irq() call
gpio: crystalcove: set IRQCHIP_SKIP_SET_WAKE for the irqchip
gpio: stp-xway: Use the of_property_read_u32 helper
gpio: pcf857x: Check for irq_set_irq_wake() failures
gpio-stp-xway: Fix enabling the highest bit of the PHY LEDs
gpio: Prevent an integer overflow in the pca953x driver
gpio: omap: rework omap_gpio_irq_startup to handle current pin state properly
gpio: omap: rework omap_gpio_request to touch only gpio specific registers
gpio: omap: rework omap_x_irq_shutdown to touch only irqs specific registers
...
This has a couple of fixes for Atmel, Samsung and Broadcom drivers. Some
preparatory patches for more upcoming Intel work is included as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=VmI2
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This has a couple of fixes for Atmel, Samsung and Broadcom drivers.
Some preparatory patches for more upcoming Intel work is included as
well"
* tag 'pwm/for-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: lpss: pci: Add support for Broxton platform
pwm: bcm-kona: Don't set polarity in probe
pwm: Add pwmchip_add_with_polarity() API
pwm: atmel: Fix incorrect CDTY value after disabling
pwm: atmel: Fix incorrect CDTY value after enabling
pwm: samsung: Use MODULE_DEVICE_TABLE() to include OF modalias
pwm: Add support to remove registered consumer lookup tables
Pull crypto update from Herbert Xu:
"Here is the crypto update for 4.2:
API:
- Convert RNG interface to new style.
- New AEAD interface with one SG list for AD and plain/cipher text.
All external AEAD users have been converted.
- New asymmetric key interface (akcipher).
Algorithms:
- Chacha20, Poly1305 and RFC7539 support.
- New RSA implementation.
- Jitter RNG.
- DRBG is now seeded with both /dev/random and Jitter RNG. If kernel
pool isn't ready then DRBG will be reseeded when it is.
- DRBG is now the default crypto API RNG, replacing krng.
- 842 compression (previously part of powerpc nx driver).
Drivers:
- Accelerated SHA-512 for arm64.
- New Marvell CESA driver that supports DMA and more algorithms.
- Updated powerpc nx 842 support.
- Added support for SEC1 hardware to talitos"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (292 commits)
crypto: marvell/cesa - remove COMPILE_TEST dependency
crypto: algif_aead - Temporarily disable all AEAD algorithms
crypto: af_alg - Forbid the use internal algorithms
crypto: echainiv - Only hold RNG during initialisation
crypto: seqiv - Add compatibility support without RNG
crypto: eseqiv - Offer normal cipher functionality without RNG
crypto: chainiv - Offer normal cipher functionality without RNG
crypto: user - Add CRYPTO_MSG_DELRNG
crypto: user - Move cryptouser.h to uapi
crypto: rng - Do not free default RNG when it becomes unused
crypto: skcipher - Allow givencrypt to be NULL
crypto: sahara - propagate the error on clk_disable_unprepare() failure
crypto: rsa - fix invalid select for AKCIPHER
crypto: picoxcell - Update to the current clk API
crypto: nx - Check for bogus firmware properties
crypto: marvell/cesa - add DT bindings documentation
crypto: marvell/cesa - add support for Kirkwood and Dove SoCs
crypto: marvell/cesa - add support for Orion SoCs
crypto: marvell/cesa - add allhwsupport module parameter
crypto: marvell/cesa - add support for all armada SoCs
...
Pull m68k update from Geert Uytterhoeven.
* 'for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Use for_each_sg()
m68k/defconfig: Update defconfigs for v4.1-rc6
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- plug a potential race related to chained interrupt handlers
- core updates which address the needs of the x86 irqdomain conversion
- new irqchip callback to support affinity settings for VCPUs
- the usual pile of updates to interrupt chip drivers
- a few helper functions to allow further cleanups and
simplifications
I have a largish pile of coccinelle scripted/verified cleanups and
simplifications pending on top of that, but I prefer to send that
towards the end of the merge window when the arch/driver changes have
hit your tree to avoid API change wreckage as far as possible"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (34 commits)
genirq: Remove bogus restriction in irq_move_mask_irq()
irqchip: atmel-aic5: Add sama5d2 support
irq: spear-shirq: Fix race in installing chained IRQ handler
irq: irq-keystone: Fix race in installing chained IRQ handler
gpio: gpio-tegra: Fix race in installing chained IRQ handler
gpio: gpio-mxs: Fix race in installing chained IRQ handler
gpio: gpio-mxc: Fix race in installing chained IRQ handler
ARM: gemini: Fix race in installing GPIO chained IRQ handler
GPU: ipu: Fix race in installing IPU chained IRQ handler
ARM: sa1100: convert SA11x0 related code to use new chained handler helper
irq: Add irq_set_chained_handler_and_data()
irqchip: exynos-combiner: Save IRQ enable set on suspend
genirq: Introduce helper function irq_data_get_affinity_mask()
genirq: Introduce helper function irq_data_get_node()
genirq: Introduce struct irq_common_data to host shared irq data
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
irqchip: gic: Simplify gic_configure_irq by using IRQCHIP_SET_TYPE_MASKED
irqchip: renesas: intc-irqpin: Improve binding documentation
genirq: Set IRQCHIP_SKIP_SET_WAKE for no_irq_chip
...
Pull NOHZ updates from Thomas Gleixner:
"A few updates to the nohz infrastructure:
- recursion protection for context tracking
- make the TIF_NOHZ inheritance smarter
- isolate cpus which belong to the NOHZ full set"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz: Set isolcpus when nohz_full is set
nohz: Add tick_nohz_full_add_cpus_to() API
context_tracking: Inherit TIF_NOHZ through forks instead of context switches
context_tracking: Protect against recursion
Pull timer updates from Thomas Gleixner:
"A rather largish update for everything time and timer related:
- Cache footprint optimizations for both hrtimers and timer wheel
- Lower the NOHZ impact on systems which have NOHZ or timer migration
disabled at runtime.
- Optimize run time overhead of hrtimer interrupt by making the clock
offset updates smarter
- hrtimer cleanups and removal of restrictions to tackle some
problems in sched/perf
- Some more leap second tweaks
- Another round of changes addressing the 2038 problem
- First step to change the internals of clock event devices by
introducing the necessary infrastructure
- Allow constant folding for usecs/msecs_to_jiffies()
- The usual pile of clockevent/clocksource driver updates
The hrtimer changes contain updates to sched, perf and x86 as they
depend on them plus changes all over the tree to cleanup API changes
and redundant code, which got copied all over the place. The y2038
changes touch s390 to remove the last non 2038 safe code related to
boot/persistant clock"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
clocksource: Increase dependencies of timer-stm32 to limit build wreckage
timer: Minimize nohz off overhead
timer: Reduce timer migration overhead if disabled
timer: Stats: Simplify the flags handling
timer: Replace timer base by a cpu index
timer: Use hlist for the timer wheel hash buckets
timer: Remove FIFO "guarantee"
timers: Sanitize catchup_timer_jiffies() usage
hrtimer: Allow hrtimer::function() to free the timer
seqcount: Introduce raw_write_seqcount_barrier()
seqcount: Rename write_seqcount_barrier()
hrtimer: Fix hrtimer_is_queued() hole
hrtimer: Remove HRTIMER_STATE_MIGRATE
selftest: Timers: Avoid signal deadlock in leap-a-day
timekeeping: Copy the shadow-timekeeper over the real timekeeper last
clockevents: Check state instead of mode in suspend/resume path
selftests: timers: Add leap-second timer edge testing to leap-a-day.c
ntp: Do leapsecond adjustment in adjtimex read path
time: Prevent early expiry of hrtimers[CLOCK_REALTIME] at the leap second edge
ntp: Introduce and use SECS_PER_DAY macro instead of 86400
...
Pull x86 core updates from Ingo Molnar:
"There were so many changes in the x86/asm, x86/apic and x86/mm topics
in this cycle that the topical separation of -tip broke down somewhat -
so the result is a more traditional architecture pull request,
collected into the 'x86/core' topic.
The topics were still maintained separately as far as possible, so
bisectability and conceptual separation should still be pretty good -
but there were a handful of merge points to avoid excessive
dependencies (and conflicts) that would have been poorly tested in the
end.
The next cycle will hopefully be much more quiet (or at least will
have fewer dependencies).
The main changes in this cycle were:
* x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
Gleixner)
- This is the second and most intrusive part of changes to the x86
interrupt handling - full conversion to hierarchical interrupt
domains:
[IOAPIC domain] -----
|
[MSI domain] --------[Remapping domain] ----- [ Vector domain ]
| (optional) |
[HPET MSI domain] ----- |
|
[DMAR domain] -----------------------------
|
[Legacy domain] -----------------------------
This now reflects the actual hardware and allowed us to distangle
the domain specific code from the underlying parent domain, which
can be optional in the case of interrupt remapping. It's a clear
separation of functionality and removes quite some duct tape
constructs which plugged the remap code between ioapic/msi/hpet
and the vector management.
- Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
injection into guests (Feng Wu)
* x86/asm changes:
- Tons of cleanups and small speedups, micro-optimizations. This
is in preparation to move a good chunk of the low level entry
code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
Brian Gerst)
- Moved all system entry related code to a new home under
arch/x86/entry/ (Ingo Molnar)
- Removal of the fragile and ugly CFI dwarf debuginfo annotations.
Conversion to C will reintroduce many of them - but meanwhile
they are only getting in the way, and the upstream kernel does
not rely on them (Ingo Molnar)
- NOP handling refinements. (Borislav Petkov)
* x86/mm changes:
- Big PAT and MTRR rework: making the code more robust and
preparing to phase out exposing direct MTRR interfaces to drivers -
in favor of using PAT driven interfaces (Toshi Kani, Luis R
Rodriguez, Borislav Petkov)
- New ioremap_wt()/set_memory_wt() interfaces to support
Write-Through cached memory mappings. This is especially
important for good performance on NVDIMM hardware (Toshi Kani)
* x86/ras changes:
- Add support for deferred errors on AMD (Aravind Gopalakrishnan)
This is an important RAS feature which adds hardware support for
poisoned data. That means roughly that the hardware marks data
which it has detected as corrupted but wasn't able to correct, as
poisoned data and raises an APIC interrupt to signal that in the
form of a deferred error. It is the OS's responsibility then to
take proper recovery action and thus prolonge system lifetime as
far as possible.
- Add support for Intel "Local MCE"s: upcoming CPUs will support
CPU-local MCE interrupts, as opposed to the traditional system-
wide broadcasted MCE interrupts (Ashok Raj)
- Misc cleanups (Borislav Petkov)
* x86/platform changes:
- Intel Atom SoC updates
... and lots of other cleanups, fixlets and other changes - see the
shortlog and the Git log for details"
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
x86/hpet: Use proper hpet device number for MSI allocation
x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
iommu, x86: Properly handle posted interrupts for IOMMU hotplug
iommu, x86: Provide irq_remapping_cap() interface
iommu, x86: Setup Posted-Interrupts capability for Intel iommu
iommu, x86: Add cap_pi_support() to detect VT-d PI capability
iommu, x86: Avoid migrating VT-d posted interrupts
iommu, x86: Save the mode (posted or remapped) of an IRTE
iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
iommu: dmar: Provide helper to copy shared irte fields
iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
iommu: Add new member capability to struct irq_remap_ops
x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
...
Pull x86 warning fixlet from Ingo Molnar:
"A build fix for certain (rare) variants of binutils that did not make
it into v4.1"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Fix overflow warning with 32-bit binutils
Pul x86 microcode updates from Ingo Molnar:
"x86 microcode loader updates from Borislav Petkov:
- early parsing of the built-in microcode
- cleanups
- misc smaller fixes"
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode: Correct CPU family related variable types
x86/microcode: Disable builtin microcode loading on 32-bit for now
x86/microcode/intel: Rename get_matching_sig()
x86/microcode/intel: Simplify get_matching_sig()
x86/microcode/intel: Simplify update_match_cpu()
x86/microcode/intel: Rename get_matching_microcode
x86/cpu/microcode: Zap changelog
x86/microcode: Parse built-in microcode early
x86/microcode/intel: Remove unused @rev arg of get_matching_sig()
x86/microcode/intel: Get rid of revision_is_newer()
Pull x86 kdump updates from Ingo Molnar:
"Three kdump robustness related improvements (Joerg Roedel)"
* 'x86-kdump-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/crash: Allocate enough low memory when crashkernel=high
x86/swiotlb: Try coherent allocations with __GFP_NOWARN
swiotlb: Warn on allocation failure in swiotlb_alloc_coherent()
Pull x86 FPU updates from Ingo Molnar:
"This tree contains two main changes:
- The big FPU code rewrite: wide reaching cleanups and reorganization
that pulls all the FPU code together into a clean base in
arch/x86/fpu/.
The resulting code is leaner and faster, and much easier to
understand. This enables future work to further simplify the FPU
code (such as removing lazy FPU restores).
By its nature these changes have a substantial regression risk: FPU
code related bugs are long lived, because races are often subtle
and bugs mask as user-space failures that are difficult to track
back to kernel side backs. I'm aware of no unfixed (or even
suspected) FPU related regression so far.
- MPX support rework/fixes. As this is still not a released CPU
feature, there were some buglets in the code - should be much more
robust now (Dave Hansen)"
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (250 commits)
x86/fpu: Fix double-increment in setup_xstate_features()
x86/mpx: Allow 32-bit binaries on 64-bit kernels again
x86/mpx: Do not count MPX VMAs as neighbors when unmapping
x86/mpx: Rewrite the unmap code
x86/mpx: Support 32-bit binaries on 64-bit kernels
x86/mpx: Use 32-bit-only cmpxchg() for 32-bit apps
x86/mpx: Introduce new 'directory entry' to 'addr' helper function
x86/mpx: Add temporary variable to reduce masking
x86: Make is_64bit_mm() widely available
x86/mpx: Trace allocation of new bounds tables
x86/mpx: Trace the attempts to find bounds tables
x86/mpx: Trace entry to bounds exception paths
x86/mpx: Trace #BR exceptions
x86/mpx: Introduce a boot-time disable flag
x86/mpx: Restrict the mmap() size check to bounds tables
x86/mpx: Remove redundant MPX_BNDCFG_ADDR_MASK
x86/mpx: Clean up the code by not passing a task pointer around when unnecessary
x86/mpx: Use the new get_xsave_field_ptr()API
x86/fpu/xstate: Wrap get_xsave_addr() to make it safer
x86/fpu/xstate: Fix up bad get_xsave_addr() assumptions
...
Pull x86 EFI updates from Ingo Molnar:
"EFI changes:
- Use idiomatic negative error values in efivar_create_sysfs_entry()
instead of returning '1' to indicate error (Dan Carpenter)
- Implement new support to expose the EFI System Resource Tables in
sysfs, which provides information for performing firmware updates
(Peter Jones)
- Documentation cleanup in the EFI handover protocol section which
falsely claimed that 'cmdline_size' needed to be filled out by the
boot loader (Alex Smith)
- Align the order of SMBIOS tables in /sys/firmware/efi/systab to
match the way that we do things for ACPI and add documentation to
Documentation/ABI (Jean Delvare)"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Work around ia64 build problem with ESRT driver
efi: Add 'systab' information to Documentation/ABI
efi: dmi: List SMBIOS3 table before SMBIOS table
efi/esrt: Fix some compiler warnings
x86, doc: Remove cmdline_size from list of fields to be filled in for EFI handover
efi: Add esrt support
efi: efivar_create_sysfs_entry() should return negative error codes
Pull x86 debugging documentation updates from Ingo Molnar:
"Documentation updates about x86 kernel stacks"
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/Documentation: Adapt Ingo's explanation on printing backtraces
x86/Documentation: Remove STACKFAULT_STACK bulletpoint
x86/Documentation: Move kernel-stacks doc one level up
Pull x86 CPU features from Ingo Molnar:
"Various CPU feature support related changes: in particular the
/proc/cpuinfo model name sanitization change should be monitored, it
has a chance to break stuff. (but really shouldn't and there are no
regression reports)"
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu/amd: Give access to the number of nodes in a physical package
x86/cpu: Trim model ID whitespace
x86/cpu: Strip any /proc/cpuinfo model name field whitespace
x86/cpu/amd: Set X86_FEATURE_EXTD_APICID for future processors
x86/gart: Check for GART support before accessing GART registers
Pull x86 cleanups from Ingo Molnar:
"Misc cleanups"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Clean up types in xlate_dev_mem_ptr() some more
x86: Deinline dma_free_attrs()
x86: Deinline dma_alloc_attrs()
x86: Remove unused TI_cpu
x86: Merge common 32-bit values in asm-offsets.c
Pull scheduler updates from Ingo Molnar:
"The main changes are:
- lockless wakeup support for futexes and IPC message queues
(Davidlohr Bueso, Peter Zijlstra)
- Replace spinlocks with atomics in thread_group_cputimer(), to
improve scalability (Jason Low)
- NUMA balancing improvements (Rik van Riel)
- SCHED_DEADLINE improvements (Wanpeng Li)
- clean up and reorganize preemption helpers (Frederic Weisbecker)
- decouple page fault disabling machinery from the preemption
counter, to improve debuggability and robustness (David
Hildenbrand)
- SCHED_DEADLINE documentation updates (Luca Abeni)
- topology CPU masks cleanups (Bartosz Golaszewski)
- /proc/sched_debug improvements (Srikar Dronamraju)"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
sched/deadline: Remove needless parameter in dl_runtime_exceeded()
sched: Remove superfluous resetting of the p->dl_throttled flag
sched/deadline: Drop duplicate init_sched_dl_class() declaration
sched/deadline: Reduce rq lock contention by eliminating locking of non-feasible target
sched/deadline: Make init_sched_dl_class() __init
sched/deadline: Optimize pull_dl_task()
sched/preempt: Add static_key() to preempt_notifiers
sched/preempt: Fix preempt notifiers documentation about hlist_del() within unsafe iteration
sched/stop_machine: Fix deadlock between multiple stop_two_cpus()
sched/debug: Add sum_sleep_runtime to /proc/<pid>/sched
sched/debug: Replace vruntime with wait_sum in /proc/sched_debug
sched/debug: Properly format runnable tasks in /proc/sched_debug
sched/numa: Only consider less busy nodes as numa balancing destinations
Revert 095bebf61a ("sched/numa: Do not move past the balance point if unbalanced")
sched/fair: Prevent throttling in early pick_next_task_fair()
preempt: Reorganize the notrace definitions a bit
preempt: Use preempt_schedule_context() as the official tracing preemption point
sched: Make preempt_schedule_context() function-tracing safe
x86: Remove cpu_sibling_mask() and cpu_core_mask()
x86: Replace cpu_**_mask() with topology_**_cpumask()
...
Pull perf fixes from Ingo Molnar:
"These are the left over fixes from the v4.1 cycle"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Fix build breakage if prefix= is specified
perf/x86: Honor the architectural performance monitoring version
perf/x86/intel: Fix PMI handling for Intel PT
perf/x86/intel/bts: Fix DS area sharing with x86_pmu events
perf/x86: Add more Broadwell model numbers
perf: Fix ring_buffer_attach() RCU sync, again
Pull perf updates from Ingo Molnar:
"Kernel side changes mostly consist of work on x86 PMU drivers:
- x86 Intel PT (hardware CPU tracer) improvements (Alexander
Shishkin)
- x86 Intel CQM (cache quality monitoring) improvements (Thomas
Gleixner)
- x86 Intel PEBSv3 support (Peter Zijlstra)
- x86 Intel PEBS interrupt batching support for lower overhead
sampling (Zheng Yan, Kan Liang)
- x86 PMU scheduler fixes and improvements (Peter Zijlstra)
There's too many tooling improvements to list them all - here are a
few select highlights:
'perf bench':
- Introduce new 'perf bench futex' benchmark: 'wake-parallel', to
measure parallel waker threads generating contention for kernel
locks (hb->lock). (Davidlohr Bueso)
'perf top', 'perf report':
- Allow disabling/enabling events dynamicaly in 'perf top':
a 'perf top' session can instantly become a 'perf report'
one, i.e. going from dynamic analysis to a static one,
returning to a dynamic one is possible, to toogle the
modes, just press 'f' to 'freeze/unfreeze' the sampling. (Arnaldo Carvalho de Melo)
- Make Ctrl-C stop processing on TUI, allowing interrupting the load of big
perf.data files (Namhyung Kim)
'perf probe': (Masami Hiramatsu)
- Support glob wildcards for function name
- Support $params special probe argument: Collect all function arguments
- Make --line checks validate C-style function name.
- Add --no-inlines option to avoid searching inline functions
- Greatly speed up 'perf probe --list' by caching debuginfo.
- Improve --filter support for 'perf probe', allowing using its arguments
on other commands, as --add, --del, etc.
'perf sched':
- Add option in 'perf sched' to merge like comms to lat output (Josef Bacik)
Plus tons of infrastructure work - in particular preparation for
upcoming threaded perf report support, but also lots of other work -
and fixes and other improvements. See (much) more details in the
shortlog and in the git log"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (305 commits)
perf tools: Configurable per thread proc map processing time out
perf tools: Add time out to force stop proc map processing
perf report: Fix sort__sym_cmp to also compare end of symbol
perf hists browser: React to unassigned hotkey pressing
perf top: Tell the user how to unfreeze events after pressing 'f'
perf hists browser: Honour the help line provided by builtin-{top,report}.c
perf hists browser: Do not exit when 'f' is pressed in 'report' mode
perf top: Replace CTRL+z with 'f' as hotkey for enable/disable events
perf annotate: Rename source_line_percent to source_line_samples
perf annotate: Display total number of samples with --show-total-period
perf tools: Ensure thread-stack is flushed
perf top: Allow disabling/enabling events dynamicly
perf evlist: Add toggle_enable() method
perf trace: Fix race condition at the end of started workloads
perf probe: Speed up perf probe --list by caching debuginfo
perf probe: Show usage even if the last event is skipped
perf tools: Move libtraceevent dynamic list to separated LDFLAGS variable
perf tools: Fix a problem when opening old perf.data with different byte order
perf tools: Ignore .config-detected in .gitignore
perf probe: Fix to return error if no probe is added
...
Pull locking updates from Ingo Molnar:
"The main changes are:
- 'qspinlock' support, enabled on x86: queued spinlocks - these are
now the spinlock variant used by x86 as they outperform ticket
spinlocks in every category. (Waiman Long)
- 'pvqspinlock' support on x86: paravirtualized variant of queued
spinlocks. (Waiman Long, Peter Zijlstra)
- 'qrwlock' support, enabled on x86: queued rwlocks. Similar to
queued spinlocks, they are now the variant used by x86:
CONFIG_ARCH_USE_QUEUED_SPINLOCKS=y
CONFIG_QUEUED_SPINLOCKS=y
CONFIG_ARCH_USE_QUEUED_RWLOCKS=y
CONFIG_QUEUED_RWLOCKS=y
- various lockdep fixlets
- various locking primitives cleanups, further WRITE_ONCE()
propagation"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
locking/lockdep: Remove hard coded array size dependency
locking/qrwlock: Don't contend with readers when setting _QW_WAITING
lockdep: Do not break user-visible string
locking/arch: Rename set_mb() to smp_store_mb()
locking/arch: Add WRITE_ONCE() to set_mb()
rtmutex: Warn if trylock is called from hard/softirq context
arch: Remove __ARCH_HAVE_CMPXCHG
locking/rtmutex: Drop usage of __HAVE_ARCH_CMPXCHG
locking/qrwlock: Rename QUEUE_RWLOCK to QUEUED_RWLOCKS
locking/pvqspinlock: Rename QUEUED_SPINLOCK to QUEUED_SPINLOCKS
locking/pvqspinlock: Replace xchg() by the more descriptive set_mb()
locking/pvqspinlock, x86: Enable PV qspinlock for Xen
locking/pvqspinlock, x86: Enable PV qspinlock for KVM
locking/pvqspinlock, x86: Implement the paravirt qspinlock call patching
locking/pvqspinlock: Implement simple paravirt support for the qspinlock
locking/qspinlock: Revert to test-and-set on hypervisors
locking/qspinlock: Use a simple write to grab the lock
locking/qspinlock: Optimize for smaller NR_CPUS
locking/qspinlock: Extract out code snippets for the next patch
locking/qspinlock: Add pending bit
...
Pull RCU updates from Ingo Molnar:
- Continued initialization/Kconfig updates: hide most Kconfig options
from unsuspecting users.
There's now a single high level configuration option:
*
* RCU Subsystem
*
Make expert-level adjustments to RCU configuration (RCU_EXPERT) [N/y/?] (NEW)
Which if answered in the negative, leaves us with a single
interactive configuration option:
Offload RCU callback processing from boot-selected CPUs (RCU_NOCB_CPU) [N/y/?] (NEW)
All the rest of the RCU options are configured automatically. Later
on we'll remove this single leftover configuration option as well.
- Remove all uses of RCU-protected array indexes: replace the
rcu_[access|dereference]_index_check() APIs with READ_ONCE() and
rcu_lockdep_assert()
- RCU CPU-hotplug cleanups
- Updates to Tiny RCU: a race fix and further code shrinkage.
- RCU torture-testing updates: fixes, speedups, cleanups and
documentation updates.
- Miscellaneous fixes
- Documentation updates
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (60 commits)
rcutorture: Allow repetition factors in Kconfig-fragment lists
rcutorture: Display "make oldconfig" errors
rcutorture: Update TREE_RCU-kconfig.txt
rcutorture: Make rcutorture scripts force RCU_EXPERT
rcutorture: Update configuration fragments for rcutree.rcu_fanout_exact
rcutorture: TASKS_RCU set directly, so don't explicitly set it
rcutorture: Test SRCU cleanup code path
rcutorture: Replace barriers with smp_store_release() and smp_load_acquire()
locktorture: Change longdelay_us to longdelay_ms
rcutorture: Allow negative values of nreaders to oversubscribe
rcutorture: Exchange TREE03 and TREE08 NR_CPUS, speed up CPU hotplug
rcutorture: Exchange TREE03 and TREE04 geometries
locktorture: fix deadlock in 'rw_lock_irq' type
rcu: Correctly handle non-empty Tiny RCU callback list with none ready
rcutorture: Test both RCU-sched and RCU-bh for Tiny RCU
rcu: Further shrink Tiny RCU by making empty functions static inlines
rcu: Conditionally compile RCU's eqs warnings
rcu: Remove prompt for RCU implementation
rcu: Make RCU able to tolerate undefined CONFIG_RCU_KTHREAD_PRIO
rcu: Make RCU able to tolerate undefined CONFIG_RCU_FANOUT_LEAF
...
Pull vfs updates from Al Viro:
"In this pile: pathname resolution rewrite.
- recursion in link_path_walk() is gone.
- nesting limits on symlinks are gone (the only limit remaining is
that the total amount of symlinks is no more than 40, no matter how
nested).
- "fast" (inline) symlinks are handled without leaving rcuwalk mode.
- stack footprint (independent of the nesting) is below kilobyte now,
about on par with what it used to be with one level of nested
symlinks and ~2.8 times lower than it used to be in the worst case.
- struct nameidata is entirely private to fs/namei.c now (not even
opaque pointers are being passed around).
- ->follow_link() and ->put_link() calling conventions had been
changed; all in-tree filesystems converted, out-of-tree should be
able to follow reasonably easily.
For out-of-tree conversions, see Documentation/filesystems/porting
for details (and in-tree filesystems for examples of conversion).
That has sat in -next since mid-May, seems to survive all testing
without regressions and merges clean with v4.1"
* 'for-linus-1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (131 commits)
turn user_{path_at,path,lpath,path_dir}() into static inlines
namei: move saved_nd pointer into struct nameidata
inline user_path_create()
inline user_path_parent()
namei: trim do_last() arguments
namei: stash dfd and name into nameidata
namei: fold path_cleanup() into terminate_walk()
namei: saner calling conventions for filename_parentat()
namei: saner calling conventions for filename_create()
namei: shift nameidata down into filename_parentat()
namei: make filename_lookup() reject ERR_PTR() passed as name
namei: shift nameidata inside filename_lookup()
namei: move putname() call into filename_lookup()
namei: pass the struct path to store the result down into path_lookupat()
namei: uninline set_root{,_rcu}()
namei: be careful with mountpoint crossings in follow_dotdot_rcu()
Documentation: remove outdated information from automount-support.txt
get rid of assorted nameidata-related debris
lustre: kill unused helper
lustre: kill unused macro (LOOKUP_CONTINUE)
...
The CESA driver calls phys_to_virt() which is not available on all
architectures.
Remove the depency on COMPILE_TEST to prevent building this driver on
non ARM architectures.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Suggested-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As the AEAD conversion is still ongoing, we do not yet wish to
export legacy AEAD implementations to user-space, as their calling
convention will change.
This patch actually disables all AEAD algorithms because some of
them (e.g., cryptd) will need to be modified to propagate this flag.
Subsequent patches will reenable them on an individual basis.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The bit CRYPTO_ALG_INTERNAL was added to stop af_alg from accessing
internal algorithms. However, af_alg itself was never modified to
actually stop that bit from being used by the user. Therefore the
user could always override it by specifying the relevant bit in the
type and/or mask.
This patch silently discards the bit in both type and mask.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch changes the RNG allocation so that we only hold a
reference to the RNG during initialisation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When seqiv is used in compatibility mode, this patch allows it
to function even when an RNG Is not available. It also changes
the RNG allocation for the new explicit seqiv interface so that
we only hold a reference to the RNG during initialisation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The RNG may not be available during early boot, e.g., the relevant
modules may not be included in the initramfs. As the RNG Is only
needed for IPsec, we should not let this prevent use of ciphers
without IV generators, e.g., for disk encryption.
This patch postpones the RNG allocation to the init function so
that one failure during early boot does not make the RNG unavailable
for all subsequent users of the same cipher.
More importantly, it lets the cipher live even if RNG allocation
fails. Of course we no longer offer IV generation and which will
fail with an error if invoked. But all other cipher capabilities
will function as usual.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The RNG may not be available during early boot, e.g., the relevant
modules may not be included in the initramfs. As the RNG Is only
needed for IPsec, we should not let this prevent use of ciphers
without IV generators, e.g., for disk encryption.
This patch postpones the RNG allocation to the init function so
that one failure during early boot does not make the RNG unavailable
for all subsequent users of the same cipher.
More importantly, it lets the cipher live even if RNG allocation
fails. Of course we no longer offer IV generation and which will
fail with an error if invoked. But all other cipher capabilities
will function as usual.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds a new crypto_user command that allows the admin to
delete the crypto system RNG. Note that this can only be done if
the RNG is currently not in use. The next time it is used a new
system RNG will be allocated.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently we free the default RNG when its use count hits zero.
This was OK when the IV generators would latch onto the RNG at
instance creation time and keep it until the instance is torn
down.
Now that IV generators only keep the RNG reference during init
time this scheme causes the default RNG to come and go at a high
frequencey. This is highly undesirable as we want to keep a single
RNG in use unless the admin wants it to be removed.
This patch changes the scheme so that the system RNG once allocated
is never removed unless a specifically requested.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently for skcipher IV generators they must provide givencrypt
as that is the whole point. We are currently replacing skcipher
IV generators with explicit IV generators. In order to maintain
backwards compatibility, we need to allow the IV generators to
still function as a normal skcipher when the RNG Is not present
(e.g., in the initramfs during boot). IOW everything but givencrypt
and givdecrypt will still work but those two will fail.
Therefore this patch assigns a default givencrypt that simply
returns an error should it be NULL.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add hwmon driver for the Microchip TC74.
The TC74 is a single-input 8-bit I2C temperature sensor,
with +-2 degrees centigrade accuracy.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
