All the vf500 based boards include the real memory size in their
dts files, so remove the zero length reg property.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Include memory node unit name in order to fix the following W=1
warnings:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi as
deprecated") the inclusion of skeleton.dtsi is deprecated, so
remove it as this file will eventually go away someday.
Move its content to the SoC dtsi file, so that the resultant dtb
is the same.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dtc now warns about missing #sound-dai-cells:
arch/arm/boot/dts/imx6ul-geam.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@2100000/i2c@21a0000/codec@a or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/imx6ul-isiot-emmc.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@2100000/i2c@21a0000/codec@a or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/imx6ul-isiot-nand.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@2100000/i2c@21a0000/codec@a or bad phandle (referred from sound-dai[0])
Lots of i.MX boards use the SGTL5000 codec, but not all get the warning
because only some reference the codec with "sound-dai" property. However,
the codec should always provide #sound-dai-cells regardless, so fix all
the occurrences.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass the memory unit-address to fix the following build warnings with W=1:
arch/arm/boot/dts/imx51-zii-rdu1.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx53-tx53-x03x.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx53-tx53-x13x.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
In theses cases an empty memory node is passed, which will be filled
by the bootloader. Passing the memory base address still allows the
bootloader to fill the memory size.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the i.MX 7Solo/Dual Application Processor Reference
Manual the ECSPI1/2/3, UART1/2/3 and SAI1/2/3 peripherals are
connected through the SPBA bus. Other similar SoCs such as i.MX 6UL
add this bus abstraction. This adds the bus also to the i.MX 7
device tree.
The i.MX SDMA driver uses this abstraction to configure watermark
levels slightly differently, so this might change behavior slightly.
There have no issues been observed before or after the patch.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX6UL(L) has a WDOG3 located at start address 0x021E0000 in the
AIPS-2 memory region [1].
[1] i.MX 6UltraLite Applications Processor Reference Manual, Rev. 1,
04/2016, Table-2-3 AIPS-2 memory map, p. 166
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable support for ARM Performance Monitoring Units available
on the Cortex-A7 CPU. There is only a single interrupt for the
PMU in both variants of the family, i.MX 7Solo and 7Dual.
Tested with perf on a i.MX 7Dual:
hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass the memory unit-adress to fix the following build warnings with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
There are cases where dts passes an empty memory node, which will be filled
by the bootloader. Passing the memory base address still allows the
bootloader to fill the memory size.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-By: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the "i.MX 6Solo/6DualLite Applications Processor
Reference Manual" Rev. 3, 09/2017 there is no LCDIF unit on the
i.MX6DL.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no pinctrl_usbotg_2 node in current Hummingboard dts files.
Drop reference to that.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the USBOTG-ID pin to the correct definition. The top
USB port stays in device-mode without this change.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass the memory unit name in order to fix the following
dtc warning with W=1:
arch/arm/boot/dts/imx28-tx28.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
They aren't needed by the etnaviv driver anymore and have been removed
from the binding.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
None of the slots support 1.8V signaling or SDIO. There is no point in
probing for a SD card on the eMMC controller.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for Advantech DMS-BA16 board, which uses
the Advantech BA-16 module.
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the Computer on Module Colibri iMX6ULL and its
Bluetooth/Wifi variant along with the development/evaluation carrier
board device trees. Follow the usual hierarchic include model,
maintaining shared configuration in imx6ull-colibri.dtsi and
imx6ull-colibri-eval-v3.dtsi respectively.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is a rebased version of patch [0].
The 32 kHz reference clock on the i.MX6UL(L) can be output by
setting the external signal XTALOSC_REF_CLK_32K in one of the
following ways [1]:
|----------------------------------------------------------|
| Signal | Pad | Mode | Direction |
|----------------------------------------------------------|
| XTALOSC_REF_CLK_32K | ENET1_RX_EN | ALT2 | O |
| | GPIO1_IO03 | ALT3 | |
| | JTAG_TCK | ALT6 | |
|----------------------------------------------------------|
Before patch [2] the mux mode for the external reference clock was
missing. The patch named the mux mode as used in the NXP Linux
4.9.11_1.0.0 release, but the Reference Manual uses the name
OSC32K_32K_OUT, e.g. in [3].
As Philipp and Shawn suggest the name from the RM should be used
instead.
[0] https://patchwork.kernel.org/patch/10172187/
[1] IMX6ULRM, Rev. 1, 04/2016, Table 58-1, p. 3649
[2] https://patchwork.kernel.org/patch/10156121/
[3] IMX6ULRM, Rev. 1, 04/2016, 30.5.47 SW_MUX_CTL_PAD_ENET1_RX_EN SW MUX
Control Register (IOMUXC_SW_MUX_CTL_PAD_ENET1_RX_EN), p. 1357
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6ull-14x14-evk.dts currently includes the imx6ul.dtsi file for an
i.MX6ULL SoC which is plain wrong.
Rename the current imx6ul-14x14-evk.dts to .dtsi and include it from
imx6ul-14x14-evk.dts and imx6ull-14x14-evk.dts, so that both can
include the appropriate SoC specific (imx6ul.dtsi/imx6ull.dtsi) file.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Put the UART clock node directly under root with a unique node name and
drop unit-address in order to fix the following build warning with W=1:
arch/arm/boot/dts/imx27-eukrea-mbimxsd27-baseboard.dtb: Warning (simple_bus_reg): Node /clocks/osc26m missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The missing last digit of the CONFIG values is added. Looks like a typo
of some sort when comparing to the downstream dt. This fixes
intermittent behavior behaviour of the ethernet controllers.
Signed-off-by: Aapo Vienamo <aapo@tuxera.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The eSDHC does not work properly if the SION bit is not set for the
bidirectional CMD signal, whatever the eSDHC instance and the selected
pad. Therefore, setting SION is mandatory for all eSDHC CMD ports. Do
this for MX25_PAD_*__ESDHCn_CMD in imx25-pinfunc.h in order to enforce
this behavior for all boards.
This had already been done for eSDHC1, but not for eSDHC2. Also, define
MX25_PAD_FEC_MDC__ESDHC2_CMD so that all the possible cases are covered
from now on.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This file had several naming inconsistencies for eSDHC:
- the instances were named sometimes SDn, sometimes SDHCn, whereas they
are named ESDHCn in the reference manual, e.g.:
MX25_PAD_SD1_CMD__SD1_CMD
MX25_PAD_D15__SDHC1_DAT7
- the data ports were named sometimes DATAn, sometimes DATn like in the
reference manual, e.g.:
MX25_PAD_SD1_DATA0__SD1_DATA0
MX25_PAD_D15__SDHC1_DAT7
- in one case, the clock port was named DAT_CLK instead of CLK:
MX25_PAD_CSI_D7__SDHC2_DAT_CLK
This change:
- introduces new definitions using the naming from the reference
manual,
- keeps definitions using the legacy naming in order not to break
compatibility for out-of-tree users (they can be removed later),
- updates the in-tree files that were using the legacy naming.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using 'at24' as fallback is now deprecated - use the full
'atmel,<model>' string.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using 'at' as the <manufacturer> part of the compatible string is now
deprecated. Use a correct string: 'atmel,<model>'.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using 'at' as the <manufacturer> part of the compatible string is now
deprecated. Use a correct string: 'atmel,<model>'.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the following warnings from dtc by adding the unit name to memory
nodes:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Converted using the following command:
perl -p0777i -e 's/memory \{\n\t\treg = \<0x+([0-9a-f])/memory\@$1$\0000000 \{\n\t\treg = <0x$1/m' `find ./arch/arm/boot/dts -name "imx*"`
The files below were manually fixed:
-imx1-ads.dts
-imx1-apf9328.dts
-imx6q-pistachio.dts
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the empty reg property from the SoC dtsi files in order to avoid
duplicate memory nodes when the correct size is passed in board dts files.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In preparation for removing 'reg = <0 0>;' from the dtsi SoC files, pass
'reg = <0 0 >;' to the dts/dtsi board files that do not pass the memory
size.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PU power domain support, GPU is the only
module inside PU power domain, and PU power
is supplied by LDO_SOC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch configures the board to output UART6 to the mikroBus.
The NXP WaRP7 board can route UART6 to the mikroBus, where an RS232
click board can be plugged in to get an additional serial port.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Default boot medium must be internal eMMC, we don't want the SDIO to be
used for these devices. This commit disables the SD card interface for
GE Healthcare Bx50v3 devices.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
PPD uses the PMIC's TSI pins in general purpose ADC mode.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Utilise new support in Atmel MaxTouch driver to drive the
touchscreen controllers reset line correctly.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In i.MX 6ULL UART8 is part of the AIPS-3 memory map instead of
AIPS-1. Clocks and interrupts remain the same.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 6ULL features another IOMUX Controller called IOMUXC
SNVS which allows to control BOOT_MODE and TAMPER pins. Add the
controller to the i.MX 6ULL specific imx6ull.dtsi device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add per-core ARM architected timer. Unfortunately bootloaders (U-Boot)
currently do not make the necessary initialization. Also specifing the
clock manually using the clock-frequency property seems not to help.
Therefor leave the timer disabled by default for now.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Cortex-A7 and its GIC support virtualization extensions. To
make use of them the CPU private interrupt needs to be specified.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX 6ULL, the pin MUX and CTRL register of BOOT_MODEx and TAMPERx
pins are available through IOMUXC_SNVS. Add additional pinfunc defines.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the PHYTEC phyBOARD-Mira with i.MX 6QuadPlus with NAND.
It is based on the phyBOARD-Mira with i.MX 6Quad/Dual and supports the
same interfaces.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Stefan Lengfeld <s.lengfeld@phytec.de>
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the PHYTEC phyBOARD-Mira Low-Cost Rapid Development Kit
with i.MX 6DualLight/Solo with NAND.
Following interfaces are supported:
- 100 MBit Ethernet
- USB Host
- RS232
- HDMI
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the PHYTEC phyBOARD-Mira Rapid Development Kit with
i.MX 6Quad/Dual with eMMC or NAND.
Following interfaces are supported:
- Gigabit Ethernet
- USB Host
- CAN
- RS232
- PCIe
- LVDS
- HDMI
Signed-off-by: Christian Hemp <c.hemp@phytec.de>
Signed-off-by: Stefan Christ <s.christ@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
