There is a HP ZBook which using ALC236 codec and need the
ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF quirk to make mute LED
and micmute LED work.
[ confirmed that the new entries are for new models that have no
proper name, so the strings are left as "HP" which will be updated
eventually later -- tiwai ]
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240102024916.19093-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add driver properties on 4 models of this laptop serie since they don't
have _DSD in the ACPI table
Signed-off-by: Dorian Cruveiller <doriancruveiller@gmail.com>
Cc: <stable@vger.kernel.org> # v6.7
Link: https://lore.kernel.org/r/20231230114312.22118-1-doriancruveiller@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP Pavilion 14 ec1xxx series uses the HP mainboard 8A0F with the
ALC287 codec.
The mute led can be enabled using the already existing
ALC287_FIXUP_HP_GPIO_LED quirk.
Tested on an HP Pavilion ec1003AU
Signed-off-by: Aabish Malik <aabishmalik3337@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231229170352.742261-3-aabishmalik3337@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These models use 2 or 4 CS35L41 amps with HDA using SPI and I2C.
Models use internal and external boost.
All models require DSD support to be added inside
cs35l41_hda_property.c
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org> # v6.7+
Link: https://lore.kernel.org/r/20231221132518.3213-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some laptops without _DSD have the SPI speed set very low in the BIOS.
Since the SPI controller uses this speed as its max speed, the SPI
transactions are very slow. Firmware download writes to many registers,
and if the SPI speed is too slow, it can take a long time to download.
For this reason, disable firmware loading if the maximum SPI speed is
too low. Without Firmware, audio playback will work, but the volume
will be low to ensure safe operation of the CS35L41.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org> # v6.7+
Link: https://lore.kernel.org/r/20231221132518.3213-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are two problems with using regcache in this module.
The amplifier has 3 addressing levels (BOOK, PAGE, REG). The firmware
contains blocks that must be written to BOOK 0x8C. The regcache doesn't
know anything about BOOK, so regcache_sync writes invalid values to the
actual BOOK.
The module handles 2 or more separate amplifiers. The amplifiers have
different register values, and the module uses only one regmap/regcache
for all the amplifiers. The regcache_sync only writes the last amplifier
used.
The module successfully restores all the written register values (RC
profile, program, configuration, calibration) without regcache.
Remove regcache functions and set regmap cache_type to REGCACHE_NONE.
Link: https://lore.kernel.org/r/21a183b5a08cb23b193af78d4b1114cc59419272.1701906455.git.soyer@irl.hu/
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Acked-by: Mark Brown <broonie@kernel.org>
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/491aeed0e2eecc3b704ec856f815db21bad3ba0e.1703202126.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialise the variables to NULL so that they cannot be uninitialised
when devm_kfree is called.
Found by static analysis.
Fixes: 8c4c216db8 ("ALSA: hda: cs35l41: Add config table to support many laptops without _DSD")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231219162232.790358-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These models use 2xCS35L41amps with HDA using SPI and I2C.
Models use internal and external boost.
All models require DSD support to be added inside
cs35l41_hda_property.c
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231218151221.388745-8-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These models use 2xCS35L41amps with HDA using SPI and I2C.
Models use internal and external boost.
All models require DSD support to be added inside
cs35l41_hda_property.c
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231218151221.388745-6-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These models use 2xCS35L41amps with HDA using SPI and I2C.
All models use Internal Boost.
Some models also use Realtek Speakers in conjunction with
CS35L41.
All models require DSD support to be added inside
cs35l41_hda_property.c
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231218151221.388745-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This make use of the CS35L41 HDA Property framework, which supports
laptops which do not have the _DSD properties in their ACPI.
Add configuration table to be able to use a generic function which allows
laptops to be supported just by adding an entry into the table.
Use configuration table function for existing system 103C89C6.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231218151221.388745-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, cur_prog/cur_conf remains at the default value (-1), while
program 0 has been loaded into the amplifiers.
In the playback hook, tasdevice_tuning_switch tries to restore the
cur_prog/cur_conf. In the runtime_resume/system_resume,
tasdevice_prmg_load tries to load the cur_prog as well.
Set cur_prog and cur_conf to 0 if available in the firmware.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/038add0bdca1f979cc7abcce8f24cbcd3544084b.1702596646.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Calling component_add starts loading the firmware, the callback function
writes the program to the amplifiers. If the module resets the
amplifiers after component_add, it happens that one of the amplifiers
does not work because the reset and program writing are interleaving.
Call tas2781_reset before component_add to ensure reliable
initialization.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/4d23bf58558e23ee8097de01f70f1eb8d9de2d15.1702511246.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the module can load the RCA but not the firmware binary, it will call
the cleanup functions. Then unloading the module causes general
protection fault due to double free.
Do not call the cleanup functions in tasdev_fw_ready.
general protection fault, probably for non-canonical address
0x6f2b8a2bff4c8fec: 0000 [#1] PREEMPT SMP NOPTI
Call Trace:
<TASK>
? die_addr+0x36/0x90
? exc_general_protection+0x1c5/0x430
? asm_exc_general_protection+0x26/0x30
? tasdevice_config_info_remove+0x6d/0xd0 [snd_soc_tas2781_fmwlib]
tas2781_hda_unbind+0xaa/0x100 [snd_hda_scodec_tas2781_i2c]
component_unbind+0x2e/0x50
component_unbind_all+0x92/0xa0
component_del+0xa8/0x140
tas2781_hda_remove.isra.0+0x32/0x60 [snd_hda_scodec_tas2781_i2c]
i2c_device_remove+0x26/0xb0
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/1a0885c424bb21172702d254655882b59ef6477a.1702510018.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The code does not properly check whether the calibration variable is
available in the EFI. If it is not available, it causes a NULL pointer
dereference.
Check the return value of the first get_variable call also.
BUG: kernel NULL pointer dereference, address: 0000000000000000
Call Trace:
<TASK>
? __die+0x23/0x70
? page_fault_oops+0x171/0x4e0
? srso_alias_return_thunk+0x5/0x7f
? schedule+0x5e/0xd0
? exc_page_fault+0x7f/0x180
? asm_exc_page_fault+0x26/0x30
? crc32_body+0x2c/0x120
? tas2781_save_calibration+0xe4/0x220 [snd_hda_scodec_tas2781_i2c]
tasdev_fw_ready+0x1af/0x280 [snd_hda_scodec_tas2781_i2c]
request_firmware_work_func+0x59/0xa0
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/f1f6583bda918f78556f67d522ca7b3b91cebbd5.1702251102.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP laptop 15-db0403ng uses the ALC236 codec and controls the mute
LED using COEF 0x07 index 1.
Sound card subsystem: Hewlett-Packard Company Device [103c:84ae]
Use the existing quirk for this model.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/e61815d0-f1c7-b164-e49d-6ca84771476a@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On ASUSTeK Z170M PLUS and Z170 PRO GAMING systems, the display codec
pins are not registered properly without the force-connect quirk. The
codec will report only one pin as having external connectivity, but i915
finds all three connectors on the system, so the two drivers are not
in sync.
Issue found with DRM igt-gpu-tools test kms_hdmi_inject@inject-audio.
Link: https://gitlab.freedesktop.org/drm/intel/-/issues/9801
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Saarinen <jani.saarinen@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231208132127.2438067-3-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add one more older NUC model that requires quirk to force all pins to be
connected. The display codec pins are not registered properly without
the force-connect quirk. The codec will report only one pin as having
external connectivity, but i915 finds all three connectors on the
system, so the two drivers are not in sync.
Issue found with DRM igt-gpu-tools test kms_hdmi_inject@inject-audio.
Link: https://gitlab.freedesktop.org/drm/igt-gpu-tools/-/issues/3
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Saarinen <jani.saarinen@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231208132127.2438067-2-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>:
This patch series adds support to the SPI framework for using multiple
chip selects.
In preparation for adding multiple CS support for a device, set/get
functions were introduces accessing spi->chip_select in
'commit 303feb3cc0 ("spi: Add APIs in spi core to set/get
spi->chip_select and spi->cs_gpiod")'.
Replace spi->chip_select with spi_get_chipselect() API.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20231125092137.2948-3-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Framework 16" laptop has the same controller as other Framework
models. Apply the presence detection quirk.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231206193927.2996-1-mario.limonciello@amd.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Framework Laptop 13 (AMD Ryzen 7040Series) has an ALC295 with
a disconnected or faulty headset mic presence detect similar to the
previous models. It works with the same quirk chain as
309d7363ca. This model has a VID:PID
of f111:0006.
Signed-off-by: Tim Bosse <flinn@timbos.se>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231206142629.388615-1-flinn@timbos.se
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo M90 Gen5 is equipped with ALC897, and it needs
ALC897_FIXUP_HEADSET_MIC_PIN quirk to make its headset mic work.
Signed-off-by: Bin Li <bin.li@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231204100450.642783-1-bin.li@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
XPS 9530 has 2 tweeters and 2 subwoofers powered by CS35L41 amplifier, SPI
connected. For subwoofers to work, it requires both to enable amplifier
support, and to enable output to subwoofers via 0x17 quirk (similalry to
XPS 9510/9520).
Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231203233006.100558-1-alex.vinarskis@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ASUS UM3504DA uses a Realtek HDA codec and two CS35L41 amplifiers via I2C.
Apply existing quirk to model.
Signed-off-by: Pascal Noël <pascal@pascalcompiles.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231202013744.12369-1-pascal@pascalcompiles.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's been reported that the runtime PM on KONTRON SinglePC (PCI SSID
1734:1232) caused a stall of playback after a bunch of invocations.
(FWIW, this looks like an timing issue, and the stall happens rather
on the controller side.)
As a workaround, disable the default power-save on this platform.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231130151321.9813-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To provide option for selecting different bit-per-sample than just the
maximum one, use the new format calculation mechanism.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20231117120610.1755254-8-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To provide option for selecting different bit-per-sample than just the
maximum one, use the new format calculation mechanism.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20231117120610.1755254-7-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To provide option for selecting different bit-per-sample than just the
maximum one, use the new format calculation mechanism.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20231117120610.1755254-6-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update mechanism for querying supported PCMs to allow for granular
format selection when container size is 32 bits. Currently always the
highest bit depth is selected, regardless of how many actual formats
codec in question supports.
Acked-by: Mark Brown <broonie@kernel.org>
Co-developed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20231117120610.1755254-3-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SPI hibernation is now supported with the latest hibernation/wake
sequences in the shared ASoC code.
This has a functional dependency on two commits:
commit 3df761bdbc ("ASoC: cs35l56: Wake transactions need to be issued
twice")
commit a47cf4dac7 ("ASoC: cs35l56: Change hibernate sequence to use
allow auto hibernate")
To protect against this, enabling hibernation is conditional on
CS35L56_WAKE_HOLD_TIME_US being defined, which indicates that the new
hibernation sequences are available.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231121154419.19435-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some older laptops using cs35l41 use firmware which does not support
the CSPL_MBOX_CMD_SPK_OUT_ENABLE command.
Firmware versions v0.28.0 and older do not support this command.
Fixes: fa3efcc36a ("ALSA: cs35l41: Use mbox command to enable speaker output for external boost")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231117163609.823627-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This state duplicates the running state inside cs_dsp, so is not necessary.
Remove it, and use cs_dsp.running instead.
This brings the CS35L41 HDA driver more inline with its ASoC version,
allowing the same state to be used when calling library functions.
Fixes: fa3efcc36a ("ALSA: cs35l41: Use mbox command to enable speaker output for external boost")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231117163609.823627-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A collection of small fixes: including a regression fix in RC1
wrt HD-audio / i915 component binding, while the rest are HD-audio
device-speific fixes / quirks.
-----BEGIN PGP SIGNATURE-----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=JybD
-----END PGP SIGNATURE-----
Merge tag 'sound-6.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes: including a regression fix in RC1 wrt
HD-audio / i915 component binding, while the rest are HD-audio
device-speific fixes / quirks"
* tag 'sound-6.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Add quirks for HP Laptops
ALSA: hda/realtek: Add quirks for ASUS 2024 Zenbooks
ALSA: hda: i915: Alays handle -EPROBE_DEFER
ALSA: hda/realtek: Enable Mute LED on HP 255 G10
ALSA: hda: cs35l56: Enable low-power hibernation mode on i2c
ALSA: hda/realtek - Enable internal speaker of ASUS K6500ZC
ALSA: hda/realtek: Enable Mute LED on HP 255 G8
ALSA: hda/realtek - Add Dell ALC295 to pin fall back table
These HP laptops use Realtek HDA codec combined with 2 or 4 CS35L41
Amplifiers using SPI with Internal Boost.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231115162116.494968-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These ASUS Zenbook laptops use Realtek HDA codec combined with
2xCS35L41 Amplifiers using SPI or I2C with External Boost or
Internal Boost.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231115162116.494968-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP 255 G10 has a mute LED that can be made to work using quirk
ALC236_FIXUP_HP_MUTE_LED_COEFBIT2.
Enable already existing quirk - at correct line to keep order
Signed-off-by: Matus Malych <matus@malych.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231114133524.11340-1-matus@malych.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This can now be re-enabled as the sequence to reliably wake the device
has been implemented in the shared ASoC code.
This has a functional dependency on commit 3df761bdbc
("ASoC: cs35l56: Wake transactions need to be issued twice")
To protect against this, enabling hibernation is conditional on
CS35L56_WAKE_HOLD_TIME_US being defined, which indicates that the new
hibernation sequences are available.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231113164029.1156669-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A collection of fixes for RC1. Majority of changes are various
ASoC driver-specific small fixes and usual HD-audio quirks, while
there are a couple of core changes: a fix in ALSA core procfs code
to avoid deadlocks at disconnection and an ASoC core fix for DAPM
clock widgets.
-----BEGIN PGP SIGNATURE-----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=6iW2
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of fixes for rc1.
The majority of changes are various ASoC driver-specific small fixes
and usual HD-audio quirks, while there are a couple of core changes: a
fix in ALSA core procfs code to avoid deadlocks at disconnection and
an ASoC core fix for DAPM clock widgets"
* tag 'sound-fix-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
OSS: dmasound/paula: Convert to platform remove callback returning void
ALSA: hda: ASUS UM5302LA: Added quirks for cs35L41/10431A83 on i2c bus
ALSA: info: Fix potential deadlock at disconnection
ASoC: nau8540: Add self recovery to improve capture quility
ALSA: hda/realtek: Add support dual speaker for Dell
ALSA: hda: Add ASRock X670E Taichi to denylist
ALSA: hda/realtek: Add quirk for ASUS UX7602ZM
ASoC: SOF: sof-client: trivial: fix comment typo
ASoC: dapm: fix clock get name
ASoC: hdmi-codec: register hpd callback on component probe
ASoC: mediatek: mt8186_mt6366_rt1019_rt5682s: trivial: fix error messages
ASoC: da7219: Improve system suspend and resume handling
ASoC: codecs: Modify macro value error
ASoC: codecs: Modify the wrong judgment of re value
ASoC: codecs: Modify the maximum value of calib
ASoC: amd: acp: fix for i2s mode register field update
ASoC: codecs: aw88399: Fix -Wuninitialized in aw_dev_set_vcalb()
ASoC: rt712-sdca: fix speaker route missing issue
ASoC: rockchip: Fix unused rockchip_i2s_tdm_match warning for !CONFIG_OF
ASoC: ti: omap-mcbsp: Fix runtime PM underflow warnings
Add ALC295 to pin fall back table.
Remove 5 pin quirks for Dell ALC295.
ALC295 was only support MIC2 for external MIC function.
ALC295 assigned model "ALC269_FIXUP_DELL1_MIC_NO_PRESENCE" for pin
fall back table.
It was assigned wrong model. So, let's remove it.
Fixes: fbc571290d ("ALSA: hda/realtek - Fixed Headphone Mic can't record on Dell platform")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/7c1998e873834df98d59bd7e0d08c72e@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Proposed patch fixes initialization of CSC3551 on the UM5302LA laptop.
Patching DSDT table is not required since ASUS did added _DSD entry.
Nothing new introduced but reused work started by Stefan B.
Currently there is no official firmware available for 10431A83 on
cirrus git unfortunately.
For testing used 104317f3 (which is also seems on i2c bus):
$ cd /lib/firmware/cirrus/ && \
for fw in $(find ./ -name '*104317f3*'); do newfw=$(echo $fw | sed 's/104317f3/10431a83/g'); echo echo "$fw -> $newfw"; ln -s $f $newfw; done
With the patch applied to 6.6.0 and obviously symlinks to 104317F3 FW,
speakers works and to my susrprise they sound quite good and loud
without distortion.
Probably confirmation from cirrus team is needed on firmware.
Signed-off-by: Vitalii Torshyn <vitaly.torshyn@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218119
Link: https://lore.kernel.org/r/CAHiQ-bCMPpCJ8eOYAaVVoqGkFixS1qTgSS4xfbZvL4oZV9LYew@mail.gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell new platform support dual speaker. But BIOS verb table only show one speaker.
It will fill verb table for second speaker. Then bind with CS AMP model.
Fixes: de90f5165b ("ALSA: hda/realtek: Add support for DELL Oasis 13/14/16 laptops")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/4dd390a77bf742b8a518ac2deee00b0f@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recent AMD platforms expose an HD-audio bus but without any actual
codecs, which is internally tied with a USB-audio device, supposedly.
It results in "no codecs" error of HD-audio bus driver, and it's
nothing but a waste of resources.
snd_hda_intel 0000:59:00.6: no codecs found!
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Link: https://lore.kernel.org/r/20231105152834.5620-1-akoskovich@pm.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
there's little I can say which isn't in the individual changelogs.
The lengthier patch series are
- "kdump: use generic functions to simplify crashkernel reservation in
arch", from Baoquan He. This is mainly cleanups and consolidation of
the "crashkernel=" kernel parameter handling.
- After much discussion, David Laight's "minmax: Relax type checks in
min() and max()" is here. Hopefully reduces some typecasting and the
use of min_t() and max_t().
- A group of patches from Oleg Nesterov which clean up and slightly fix
our handling of reads from /proc/PID/task/... and which remove
task_struct.therad_group.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZUQP9wAKCRDdBJ7gKXxA
jmOAAQDh8sxagQYocoVsSm28ICqXFeaY9Co1jzBIDdNesAvYVwD/c2DHRqJHEiS4
63BNcG3+hM9nwGJHb5lyh5m79nBMRg0=
=On4u
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2023-11-02-14-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
"As usual, lots of singleton and doubleton patches all over the tree
and there's little I can say which isn't in the individual changelogs.
The lengthier patch series are
- 'kdump: use generic functions to simplify crashkernel reservation
in arch', from Baoquan He. This is mainly cleanups and
consolidation of the 'crashkernel=' kernel parameter handling
- After much discussion, David Laight's 'minmax: Relax type checks in
min() and max()' is here. Hopefully reduces some typecasting and
the use of min_t() and max_t()
- A group of patches from Oleg Nesterov which clean up and slightly
fix our handling of reads from /proc/PID/task/... and which remove
task_struct.thread_group"
* tag 'mm-nonmm-stable-2023-11-02-14-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (64 commits)
scripts/gdb/vmalloc: disable on no-MMU
scripts/gdb: fix usage of MOD_TEXT not defined when CONFIG_MODULES=n
.mailmap: add address mapping for Tomeu Vizoso
mailmap: update email address for Claudiu Beznea
tools/testing/selftests/mm/run_vmtests.sh: lower the ptrace permissions
.mailmap: map Benjamin Poirier's address
scripts/gdb: add lx_current support for riscv
ocfs2: fix a spelling typo in comment
proc: test ProtectionKey in proc-empty-vm test
proc: fix proc-empty-vm test with vsyscall
fs/proc/base.c: remove unneeded semicolon
do_io_accounting: use sig->stats_lock
do_io_accounting: use __for_each_thread()
ocfs2: replace BUG_ON() at ocfs2_num_free_extents() with ocfs2_error()
ocfs2: fix a typo in a comment
scripts/show_delta: add __main__ judgement before main code
treewide: mark stuff as __ro_after_init
fs: ocfs2: check status values
proc: test /proc/${pid}/statm
compiler.h: move __is_constexpr() to compiler.h
...
Most of changes at this time are for ASoC, spread over ASoC core and
drivers due to the API prefix standardization. Other than that, there
have little change wrt API, rather lots of driver-specific updates and
fixes. Some highlight below:
ASoC:
- Standardization of API prefix
- GPIO API usage improvements
- Support for HDA patches
- Lots of work on SOF, including crash dump support
- Fixes for noise when stopping some Sounwire CODECs
- Support for AMD platforms with es83xx, AMD ACP 6.3 and 7.0, Awinc
AT87390 and AW88399, many Intel platforms, many Mediatek platforms,
Qualcomm SM6115 and SC7180 platforms, Richtek RTQ9128 and Texas
Instruments TAS575x
HD-audio and USB-audio:
- Deferred probe support of audio component binding
- More fixes and enhancements for Cirrus subcodecs
- USB Scarlett2 mixer and McIntosh DSD quirk
Others:
- More enhancement of snd-aloop driver
- Update MAINTAINERS entry for linux-sound mailing list
-----BEGIN PGP SIGNATURE-----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=2/dI
-----END PGP SIGNATURE-----
Merge tag 'sound-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Most of changes at this time are for ASoC, spread over ASoC core and
drivers due to the API prefix standardization.
Other than that, there have little change wrt API, rather lots of
driver-specific updates and fixes.
Some highlight below:
ASoC:
- Standardization of API prefix
- GPIO API usage improvements
- Support for HDA patches
- Lots of work on SOF, including crash dump support
- Fixes for noise when stopping some Sounwire CODECs
- Support for AMD platforms with es83xx, AMD ACP 6.3 and 7.0, Awinc
AT87390 and AW88399, many Intel platforms, many Mediatek platforms,
Qualcomm SM6115 and SC7180 platforms, Richtek RTQ9128 and Texas
Instruments TAS575x
HD-audio and USB-audio:
- Deferred probe support of audio component binding
- More fixes and enhancements for Cirrus subcodecs
- USB Scarlett2 mixer and McIntosh DSD quirk
Others:
- More enhancement of snd-aloop driver
- Update MAINTAINERS entry for linux-sound mailing list"
* tag 'sound-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (485 commits)
ALSA: hda: cs35l41: Fix missing error code in cs35l41_smart_amp()
ALSA: hda: cs35l41: mark cs35l41_verify_id() static
ASoC: codecs: wsa883x: make use of new mute_unmute_on_trigger flag
ASoC: soc-dai: add flag to mute and unmute stream during trigger
ASoC: ams-delta.c: use component after check
ASoC: amd: acp: select SND_SOC_AMD_ACP_LEGACY_COMMON for ACP63
ASoC: codecs: aw88399: fix typo in Kconfig select
ASoC: amd: acp: add ACPI dependency
ASoC: Intel: avs: Add rt5514 machine board
ASoC: Intel: avs: Add rt5514 machine board
ALSA: scarlett2: Add missing check with firmware version control
ALSA: virtio: use ack callback
ALSA: scarlett2: Remap Level Meter values
ALSA: scarlett2: Allow passing any output to line_out_remap()
ALSA: scarlett2: Add support for reading firmware version
ALSA: scarlett2: Rename Gen 3 config sets
ALSA: scarlett2: Rename scarlett_gen2 to scarlett2
ASoC: cs35l41: Detect CSPL errors when sending CSPL commands
ALSA: hda: cs35l41: Check CSPL state after loading firmware
ALSA: hda: cs35l41: Do not unload firmware before reset in system suspend
...
-----BEGIN PGP SIGNATURE-----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=G//C
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Use acpi_evaluate_dsm_typed() instead of open-coding _DSM
evaluation to learn device characteristics (Andy Shevchenko)
- Tidy multi-function header checks using new PCI_HEADER_TYPE_MASK
definition (Ilpo Järvinen)
- Simplify config access error checking in various drivers (Ilpo
Järvinen)
- Use pcie_capability_clear_word() (not
pcie_capability_clear_and_set_word()) when only clearing (Ilpo
Järvinen)
- Add pci_get_base_class() to simplify finding devices using base
class only (ignoring subclass and programming interface) (Sui
Jingfeng)
- Add pci_is_vga(), which includes ancient PCI_CLASS_NOT_DEFINED_VGA
devices from before the Class Code was added to PCI (Sui Jingfeng)
- Use pci_is_vga() for vgaarb, sysfs "boot_vga", virtio, qxl to
include ancient VGA devices (Sui Jingfeng)
Resource management:
- Make pci_assign_unassigned_resources() non-init because sparc uses
it after init (Randy Dunlap)
Driver binding:
- Retain .remove() and .probe() callbacks (previously __init) because
sysfs may cause them to be called later (Uwe Kleine-König)
- Prevent xHCI driver from claiming AMD VanGogh USB3 DRD device, so
it can be claimed by dwc3 instead (Vicki Pfau)
PCI device hotplug:
- Add Ampere Altra Attention Indicator extension driver for acpiphp
(D Scott Phillips)
Power management:
- Quirk VideoPropulsion Torrent QN16e with longer delay after reset
(Lukas Wunner)
- Prevent users from overriding drivers that say we shouldn't use
D3cold (Lukas Wunner)
- Avoid PME from D3hot/D3cold for AMD Rembrandt and Phoenix USB4
because wakeup interrupts from those states don't work if amd-pmc
has put the platform in a hardware sleep state (Mario Limonciello)
IOMMU:
- Disable ATS for Intel IPU E2000 devices with invalidation message
endianness erratum (Bartosz Pawlowski)
Error handling:
- Factor out interrupt enable/disable into helpers (Kai-Heng Feng)
Peer-to-peer DMA:
- Fix flexible-array usage in struct pci_p2pdma_pagemap in case we
ever use pagemaps with multiple entries (Gustavo A. R. Silva)
ASPM:
- Revert a change that broke when drivers disabled L1 and users later
enabled an L1.x substate via sysfs, and fix a similar issue when
users disabled L1 via sysfs (Heiner Kallweit)
Endpoint framework:
- Fix double free in __pci_epc_create() (Dan Carpenter)
- Use IS_ERR_OR_NULL() to simplify endpoint core (Ruan Jinjie)
Cadence PCIe controller driver:
- Drop unused "is_rc" member (Li Chen)
Freescale Layerscape PCIe controller driver:
- Enable 64-bit addressing in endpoint mode (Guanhua Gao)
Intel VMD host bridge driver:
- Fix multi-function header check (Ilpo Järvinen)
Microsoft Hyper-V host bridge driver:
- Annotate struct hv_dr_state with __counted_by (Kees Cook)
NVIDIA Tegra194 PCIe controller driver:
- Drop setting of LNKCAP_MLW (max link width) since dw_pcie_setup()
already does this via dw_pcie_link_set_max_link_width() (Yoshihiro
Shimoda)
Qualcomm PCIe controller driver:
- Use PCIE_SPEED2MBS_ENC() to simplify encoding of link speed
(Manivannan Sadhasivam)
- Add a .write_dbi2() callback so DBI2 register writes, e.g., for
setting the BAR size, work correctly (Manivannan Sadhasivam)
- Enable ASPM for platforms that use 1.9.0 ops, because the PCI core
doesn't enable ASPM states that haven't been enabled by the
firmware (Manivannan Sadhasivam)
Renesas R-Car Gen4 PCIe controller driver:
- Add DesignWare core support (set max link width, EDMA_UNROLL flag,
.pre_init(), .deinit(), etc) for use by R-Car Gen4 driver
(Yoshihiro Shimoda)
- Add driver and DT schema for DesignWare-based Renesas R-Car Gen4
controller in both host and endpoint mode (Yoshihiro Shimoda)
Xilinx NWL PCIe controller driver:
- Update ECAM size to support 256 buses (Thippeswamy Havalige)
- Stop setting bridge primary/secondary/subordinate bus numbers,
since PCI core does this (Thippeswamy Havalige)
Xilinx XDMA controller driver:
- Add driver and DT schema for Zynq UltraScale+ MPSoCs devices with
Xilinx XDMA Soft IP (Thippeswamy Havalige)
Miscellaneous:
- Use FIELD_GET()/FIELD_PREP() to simplify and reduce use of _SHIFT
macros (Ilpo Järvinen, Bjorn Helgaas)
- Remove logic_outb(), _outw(), outl() duplicate declarations (John
Sanpe)
- Replace unnecessary UTF-8 in Kconfig help text because menuconfig
doesn't render it correctly (Liu Song)"
* tag 'pci-v6.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (102 commits)
PCI: qcom-ep: Add dedicated callback for writing to DBI2 registers
PCI: Simplify pcie_capability_clear_and_set_word() to ..._clear_word()
PCI: endpoint: Fix double free in __pci_epc_create()
PCI: xilinx-xdma: Add Xilinx XDMA Root Port driver
dt-bindings: PCI: xilinx-xdma: Add schemas for Xilinx XDMA PCIe Root Port Bridge
PCI: xilinx-cpm: Move IRQ definitions to a common header
PCI: xilinx-nwl: Modify ECAM size to enable support for 256 buses
PCI: xilinx-nwl: Rename the NWL_ECAM_VALUE_DEFAULT macro
dt-bindings: PCI: xilinx-nwl: Modify ECAM size in the DT example
PCI: xilinx-nwl: Remove redundant code that sets Type 1 header fields
PCI: hotplug: Add Ampere Altra Attention Indicator extension driver
PCI/AER: Factor out interrupt toggling into helpers
PCI: acpiphp: Allow built-in drivers for Attention Indicators
PCI/portdrv: Use FIELD_GET()
PCI/VC: Use FIELD_GET()
PCI/PTM: Use FIELD_GET()
PCI/PME: Use FIELD_GET()
PCI/ATS: Use FIELD_GET()
PCI/ATS: Show PASID Capability register width in bitmasks
PCI/ASPM: Fix L1 substate handling in aspm_attr_store_common()
...
When firmware status is invalid, assign -EINVAL to ret as ret is '0' at
that point and returning success is incorrect when firmware status is
invalid.
Fixes: a51d8ba03a ("ALSA: hda: cs35l41: Check CSPL state after loading firmware")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20231030070836.3234385-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The newly introduced function is global but only called in this one
file and has no extern prototype, so it should probably be static:
sound/pci/hda/cs35l41_hda.c:733:5: error: no previous prototype for 'cs35l41_verify_id' [-Werror=missing-prototypes]
733 | int cs35l41_verify_id(struct cs35l41_hda *cs35l41, unsigned int *regid, unsigned int *reg_revid)
Fixes: 881b7bce0c ("ALSA: hda: cs35l41: Run boot process during resume callbacks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20231027152515.482411-1-arnd@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CSPL firmware should be in RUNNING or PAUSED state after loading.
If not, the firmware has not been loaded correctly, and we can unload
it and pass the error up.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231026150558.2105827-8-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Given the part is about to reset due to system suspend, and we are
already in hibernate, there is no need to wake up the amp, just to get
it ready to be reset. We just need to ensure cs_dsp is ready for reset
by resetting the states.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231026150558.2105827-7-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To ensure the chip has correctly reset during probe and system suspend,
we need to force a software reset, in case of systems where the
hardware reset is not available.
The software reset register was labelled as volatile but not readable,
however, it is readable, (just returns 0x0). Adding it to readable
registers means it will be correctly treated as volatile, and thus
will not be cached.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231026150558.2105827-6-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
During initial probe, after reset is asserted for the first time, the
driver goes through a boot process to ensure the amp is ready to be
used. This involves verifying a boot flag, as well as verifying the
chip ids.
This is necessary since it is possible for the amp to have been fully
reset by the system suspend calls.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231026150558.2105827-5-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To ensure we are in a known state, exiting from reset at the point of
probe or in system resume, assert reset before we de-assert it.
Since the BIOS may enter into a pre-boot environment to control the
amps (for example for boot beep), we need to ensure we start from a
known, reset state prior to probe or system resume.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231026150558.2105827-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some system suspend modes may remove power supplies.
To ensure we are not running during this time, we should assert reset.
Note: since the amps use a shared reset, asserting reset prior to
system suspend only works if the amps are suspended in the reverse
order to probe.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231026150558.2105827-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This laptop has an incorrect setting in its _DSD for boost type, but
the rest of the _DSD is correct, and we can still use the reset label
to obtain the reset gpio.
Also fix channel map so that amp 0 is right, and amp 1 is left.
Fixes: 581523ee36 ("ALSA: hda: cs35l41: Override the _DSD for HP Zbook Fury 17 G9 to correct boost type")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231026150558.2105827-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is quite a large set of changes but mostly due to API cleanups and
in driver specific ways rather than due to anything subsystem wide.
Highlights include:
- Standardisation of API prefixes on snd_soc_, removing asoc_.
- GPIO API usage improvements.
- Support for HDA patches.
- Lots of work on SOF, including crash dump support.
- Support for AMD platforms with es83xx, Awinc AT87390, many Intel
platforms, many Mediatek platforms, Qualcomm SM6115, Richtek RTQ9128
and Texas Instruments TAS575x.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmUy6X8ACgkQJNaLcl1U
h9Cv7Qf+PO4ucl/rFITWAp2Ta9fw7Z5J6UCiXiR54TPgAiLJrpKSi3rbYTXjO90Y
1NNOdoMKr109zdOpdSZI7EX0GgWQbGbdB40nxESdTcojAloRH0jt4RaF7G7B7+86
b8PGlVPLLV/4zFf9f2gpEKPcKhRRRKYOBIEB+amfjWpdXVrqPD3zS/S16Q3Hn4Gy
Fx9b9X/lVDG9uqJomHpunEdViZjkm5CCNzdyAhHH99afiqSe//pevx6/FpzAHyng
AZgE9Yfq4Xw4pdzDdGVfYC+L1GZiHIDRzsusz6aPA5nrMhSn0ru8PMGtmQQTzyhb
PLYw0OW8cWymfqwal8wrNGJfSZ8IGA==
=lN5P
-----END PGP SIGNATURE-----
Merge tag 'asoc-v6.7' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v6.7
This is quite a large set of changes but mostly due to API cleanups and
in driver specific ways rather than due to anything subsystem wide.
Highlights include:
- Standardisation of API prefixes on snd_soc_, removing asoc_.
- GPIO API usage improvements.
- Support for HDA patches.
- Lots of work on SOF, including crash dump support.
- Support for AMD platforms with es83xx, Awinc AT87390, many Intel
platforms, many Mediatek platforms, Qualcomm SM6115, Richtek RTQ9128
and Texas Instruments TAS575x.
[ the merge conflicts around SOF Intel HD-audio and CS35L41 subcodec
drivers are resolved here -- tiwai ]
Now that all drivers have moved from modprobe loading to
handling -EPROBE_DEFER, we can remove the argument again.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20231009115437.99976-14-maarten.lankhorst@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that we can use -EPROBE_DEFER, it's no longer required to spin off
the snd_hdac_i915_init into a workqueue.
Use the -EPROBE_DEFER mechanism instead, which must be returned in the
probe function.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20231009115437.99976-11-maarten.lankhorst@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Xe is a new GPU driver that re-uses the display (and sound) code from
i915. It's no longer possible to load i915, as the GPU can be driven
by the xe driver instead.
The new behavior will return -EPROBE_DEFER, and wait for a compatible
driver to be loaded instead of modprobing i915.
Converting all drivers at the same time is a lot of work, instead we
will convert each user one by one.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20231009115437.99976-8-maarten.lankhorst@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Extract nifty FILE_LINE useful for printk style debugging:
printk("%s\n", FILE_LINE);
It should not be used en mass probably because __FILE__ string literals
can be merged while FILE_LINE's won't. But for debugging it is what
the doctor ordered.
Don't add leading and trailing underscores, they're painful to type.
Trust me, I've tried both versions.
Link: https://lkml.kernel.org/r/ebf12ac4-5a61-4b12-b8b0-1253eb371332@p183
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
ASUS platform Headset Mic was disable by default.
Assigned verb table for Mic pin will enable it.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1155d914c20c40569f56d36c79254879@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This HP Laptop uses ALC236 codec with COEF 0x07 controlling the
mute LED. Enable existing quirk for this device.
Signed-off-by: Luka Guzenko <l.guzenko@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231016221328.1521674-1-l.guzenko@web.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AudioDSP firmware is the one who kicks SDxFIFOS calculation when a
stream is decoupled mode. During firmware bring up procedure, there is
no firmware running and the code-loading stream is always a decoupled
one. So, there is none to trigger the calculation and we end up with
false-positive timeout (-110) messages.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20231006102857.749143-4-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SDxFIFOS register indicates the fifo size directly. There is no need to
modify the value after reading the register.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20231006102857.749143-3-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While grep'ing for SIS7012, I noticed that there is
only one reference to it in sound/pci/intel8x0m.c,
while most of its code lives in sound/pci/intel8x0.c.
This probably was a simple copy'n'paste mistake, as
the sound/pci/intel8x0m.c driver implements support
for SIS7013 (see DEVICE_SIS), and the two devices
seem to share the same behavior / registers.
Signed-off-by: Thomas Perl <m@thp.io>
Link: https://lore.kernel.org/r/5E4B5CA1-1109-4C82-A581-838ACF19A15D@thp.io
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Intel RVP board (0x12cc) has Headset Mic issue for reboot.
If system plugged headset when system reboot the headset Mic was gone.
Fixes: 1a93f10c5b ("ALSA: hda/realtek: Add "Intel Reference board" and "NUC 13" SSID in the ALC256")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/28112f54c0c6496f97ac845645bc0256@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is an unlikely but possible double free when loading firmware,
and a missing free calls if a firmware is successfully requested but
the coefficient file request fails, leading to the fallback firmware
request occurring without clearing the previously loaded firmware.
Fixes: cd40dad2ca ("ALSA: hda: cs35l41: Ensure firmware/tuning pairs are always loaded")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202309291331.0JUUQnPT-lkp@intel.com/
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231003142138.180108-1-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The "ret" variable is zero but we should return -EINVAL.
Fixes: 2144833e7b ("ALSA: hda: cirrus_scodec: Add KUnit test")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/5eea7fd5-67c8-4ed4-b5b3-b85dfb7572cc@moroto.mountain
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct hda_conn_list.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Cezary Rojewski <cezary.rojewski@intel.com>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230922175042.work.547-kees@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the CS35L41 amp is requested to mute using the ACPI
notification mechanism, userspace is not notified that the amp
is muted. To allow userspace to know about the mute, add an
ALSA control which tracks the forced mute override.
This control does not track the overall mute state of the amp,
since the amp is only unmuted during playback anyway, instead
it tracks the mute override request from the ACPI notification.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230921162849.1988124-5-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some laptops require a hardware based mute system, where when a hotkey
is pressed, it forces the amp to be muted.
For CS35L41, when the hotkey is pressed, an acpi notification is sent
to the CS35L41 Device Node. The driver needs to handle this notification
and call a _DSM function to retrieve the mute state.
Since the amp is only muted during playback, the driver will only mute
or unmute if playback is occurring, otherwise it will save the mute
state for when playback starts.
This uses the ACPI Notification mechanism, where a handler has been
registered in the component master, which notifies each amp through
the component binding.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230921162849.1988124-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For systems which have support for ACPI notifications, add a mechanism to
register a handler for ACPI notifications and then call the acpi_notify
api on the bound components.
Registering a handler in the Realtek HDA driver, allows a single handler to
be registered, which then calls into all the components, rather than
attempting to register the same handler multiple times, once for each
component.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230921162849.1988124-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some systems support a notification from ACPI, which can be used
for different things.
Only one handler can be registered for the acpi notification, but all
amps need to receive that notification, we can register a single handler
inside the component master, so that it can then notify through the
component framework.
This is required to support mute notifications from ACPI.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230921162849.1988124-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is merge model ALC287_FIXUP_THINKPAD_I2S_SPK and
ALC287_FIXUP_CS35L41_I2C_2_THINKPAD_ACPI.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Fixes: f7b069cf08 ("ALSA: hda/realtek: Fix generic fixup definition for cs35l41 amp")
Link: https://lore.kernel.org/r/82a45234327c4c50b4988a27e9f64c37@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The KUnit test for cirrus_scodec uses GPIO library functions so select
GPIOLIB in Kconfig.
This fixes the ld failures on builds that didn't already select GPIOLIB.
ld: vmlinux.o: in function `cirrus_scodec_test_gpio_get':
sound/pci/hda/cirrus_scodec_test.c:40: undefined reference to
`gpiochip_get_data'
ld: vmlinux.o: in function `cirrus_scodec_test_gpio_probe':
sound/pci/hda/cirrus_scodec_test.c:94: undefined reference to
`gpiochip_generic_request'
ld: sound/pci/hda/cirrus_scodec_test.c:94: undefined reference to
`gpiochip_generic_free'
ld: sound/pci/hda/cirrus_scodec_test.c:95: undefined reference to
`devm_gpiochip_add_data_with_key'
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309201646.NnjfKPWk-lkp@intel.com/
Fixes: 2144833e7b ("ALSA: hda: cirrus_scodec: Add KUnit test")
Link: https://lore.kernel.org/r/20230920090338.29345-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New platform SSID:0x231f.
0x17 was only speaker pin, DAC assigned will be 0x03. Headphone
assigned to 0x02.
Playback via headphone will get EQ filter processing.
So, it needs to swap DAC.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/8d63c6e360124e3ea2523753050e6f05@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use RUNTIME_PM_OPS() instead of the old SET_RUNTIME_PM_OPS().
This means we don't need __maybe_unused on the functions.
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230919081153.19793-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a KUnit test for cirrus_scodec_get_speaker_id(). It is impractical
to have enough hardware with every possible permutation of speaker id.
So use a test harness to test all theoretically supported options.
The test harness consists of:
- a mock GPIO controller.
- a mock struct device to represent the scodec driver
- software nodes to provide the fwnode info that would normally come
from ACPI.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230918095129.440-3-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add handling of the "spk-id-gpios" _DSD property. If present, the
value indicated by the GPIOs is appended to the subsystem-id
part of the firmware name to load the appropriate tunings for that
speaker.
Some manufacturers use multiple sources of speakers, which need
different tunings for best performance. On these models the type
of speaker fitted is indicated by the values of one or more GPIOs.
The number formed by the GPIOs identifies the tuning required.
The speaker ID is only used in combination with a _SUB identifier
because the value is only meaningful if the exact model is known.
The code to get the speaker ID value has been implemented as a
new library so that the cs35l41_hda driver can be switched in
future to share common code. This library can be extended for
other common functionality shared by Cirrus Logic amp drivers.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230918095129.440-2-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The filling of card->longname can be gracefully truncated, as it's
only informative. Use scnprintf() and suppress the superfluous
compile warning with -Wformat-truncation.
Link: https://lore.kernel.org/r/20230915091313.5988-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
add_control_with_pfx() constructs a mixer name element with the fixed
size, and it got compile warnings with -Wformat-truncation.
Although the size overflow is very unlikely, let's have a sanity check
of the string size and returns the error if it really doesn't fit
instead of silent truncation.
Link: https://lore.kernel.org/r/20230915082802.28684-14-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CMIPCI driver got compile warnings with -Wformat-truncation at a
couple of plain sprintf() usages. Use scnprintf() for filling the
longname string for avoiding the warnings.
Link: https://lore.kernel.org/r/20230915082802.28684-13-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In cs35l56_hda_read_acpi() do not return if ACPI _SUB is missing.
A missing _SUB means that the driver cannot load a system-specific
firmware, because the firmware is identified by the _SUB. But it can
fallback to a generic firmware. Unfortunately this was being handled
by immediately returning 0, which would skip the remaining ACPI
configuration in cs35l56_hda_read_acpi() and so it would not get the
RESET GPIO.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Link: https://lore.kernel.org/r/20230914152525.20829-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo ThinkCentre M70q had boot up pop noise.
Disable power save will solve pop issue.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/315900e2efef42fd9855eacfeb443abd@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The final return in cs35l56_hda_posture_get() was returning the
value of 'ret', but ret is always zero at this point. So this
can be a simple 'return 0'.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230914140852.7112-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
UX3402VA and UX3402ZA models require different hex values, so comibining
them into one model is incorrect.
Fixes: 491a4ccd8a ("ALSA: hda/realtek: Add quirk for ASUS Zenbook using CS35L41")
Signed-off-by: Knyazev Arseniy <poseaydone@ya.ru>
Link: https://lore.kernel.org/r/20230913053343.119798-1-poseaydone@ya.ru
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Do not allow the CS35L56 to be put into its lowest power
"hibernation" mode. This only affects I2C because "hibernation"
is already disabled on SPI.
Recent firmwares need a different wake-up sequence. Until
that sequence has been specified, the chip "hibernation" mode
must be disabled otherwise it can intermittently fail to wake.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230912132739.3478441-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If system has two speakers and one connect to 0x14 pin, use this
function will disable it.
Fixes: e43252db7e ("ALSA: hda/realtek - ALC287 I2S speaker platform support")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/e3f2aac3fe6a47079d728a6443358cc2@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Driver remove() must call pm_runtime_dont_use_autosuspend().
Drivers that call pm_runtime_use_autosuspend() must disable
it in driver remove(). Unfortunately until recently this was
only mentioned in 1 line in a 900+ line document so most
people hadn't noticed this. It has only recently been added
to the kerneldoc of pm_runtime_use_autosuspend().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Link: https://lore.kernel.org/r/20230908101223.2656901-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the remaining dev_err() calls in probe() with dev_err_probe(),
to improve consistency.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230907171010.1447274-12-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the documentation, drivers are responsible for undoing at
removal time all runtime PM changes done during probing.
Hence, add the missing calls to pm_runtime_dont_use_autosuspend(), which
are necessary for undoing pm_runtime_use_autosuspend().
Fixes: 1873ebd30c ("ALSA: hda: cs35l41: Support Hibernation during Suspend")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230907171010.1447274-11-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If component_add() fails, probe() returns without calling
pm_runtime_put(), which leaves the runtime PM usage counter incremented.
Fix the issue by jumping to err_pm label and drop the now unnecessary
pm_runtime_disable() call.
Fixes: 7b2f3eb492 ("ALSA: hda: cs35l41: Add support for CS35L41 in HDA systems")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230907171010.1447274-10-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Enabling the active/passive shared boosts requires setting SYNC_EN, but
*not* before receiving the PLL Lock signal.
Due to improper error handling, it was not obvious that waiting for the
completion operation times out and, consequently, the shared boost is
never activated.
Further investigations revealed the signal is triggered while
snd_pcm_start() is executed, right after receiving the
SNDRV_PCM_TRIGGER_START command, which happens long after the
SND_SOC_DAPM_PRE_PMU event handler is invoked as part of
snd_pcm_prepare(). That is where cs35l41_global_enable() is called
from.
Increasing the wait duration doesn't help, as it only causes an
unnecessary delay in the invocation of snd_pcm_start(). Moving the wait
and the subsequent regmap operations to the SNDRV_PCM_TRIGGER_START
callback is not a solution either, since they would be executed in an
IRQ-off atomic context.
Solve the issue by setting the SYNC_EN bit in PWR_CTRL3 register right
after receiving the PLL Lock interrupt.
Additionally, drop the unnecessary writes to PWR_CTRL1 register, part of
the original mdsync_up_seq, which would have toggled GLOBAL_EN with
unwanted consequences on PLL locking behavior.
Fixes: f503056493 ("ALSA: cs35l41: Add shared boost feature")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: David Rhodes <david.rhodes@cirrus.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230907171010.1447274-5-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
0x17 was only speaker pin, DAC assigned will be 0x03. Headphone
assigned to 0x02.
Playback via headphone will get EQ filter processing. So,it needs to
swap DAC.
Tested-by: Mark Pearson <mpearson@lenovo.com>
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/4e4cfa1b3b4c46838aecafc6e8b6f876@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The LED for the mic mute button is controlled by GPIO2.
The mute button LED is slightly more complex, it's controlled by two bits
in coeff 0x0b.
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/2693091.mvXUDI8C0e@fabians-envy
Signed-off-by: Takashi Iwai <tiwai@suse.de>
struct i2c_driver::probe_new is about to go away. Switch the driver to
use the probe callback with the same prototype.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Link: https://lore.kernel.org/r/20230824200219.9569-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Before committing 79597c8bf6, *rac97 always be NULL if there is
an error. When error happens, make sure *rac97 is NULL is safer.
For examble, in snd_vortex_mixer():
err = snd_ac97_mixer(pbus, &ac97, &vortex->codec);
vortex->isquad = ((vortex->codec == NULL) ?
0 : (vortex->codec->ext_id&0x80));
If error happened but vortex->codec isn't NULL, this may cause some
problems.
Move the judgement order to be clearer and better.
Fixes: 79597c8bf6 ("ALSA: ac97: Fix possible NULL dereference in snd_ac97_mixer")
Suggested-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20230823025212.1000961-1-suhui@nfschina.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CS35L41 HDA driver requires ACPI to contain correct _DSD properties to
correctly configure the device. Whilst the HP Zbook Fury 17 G9 contains
valid _DSD properties, the boost type has been configured incorrectly
in the _DSD for this laptop. We can override these properties to fix
the boost type.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230823143956.755758-1-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like a few other drivers, YMFPCI driver needs to clean up with
snd_card_free() call at an error path of the probe; otherwise the
other devres resources are released before the card and it results in
the UAF.
This patch uses the helper for handling the probe error gracefully.
Fixes: f33fc15767 ("ALSA: ymfpci: Create card with device-managed snd_devm_card_new()")
Cc: <stable@vger.kernel.org>
Reported-and-tested-by: Takashi Yano <takashi.yano@nifty.ne.jp>
Closes: https://lore.kernel.org/r/20230823135846.1812-1-takashi.yano@nifty.ne.jp
Link: https://lore.kernel.org/r/20230823161625.5807-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the rme9652 driver code to use the new unified PCM
copy callback. It's a straightforward conversion from *_user() to
*_iter() variants.
Note that copy_from/to_iter() returns the copied bytes, hence the
error condition is adjusted accordingly.
Link: https://lore.kernel.org/r/20230815190136.8987-14-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the hdsp driver code to use the new unified PCM
copy callback. It's a straightforward conversion from *_user() to
*_iter() variants.
Note that copy_from/to_iter() returns the copied bytes, hence the
error condition is adjusted accordingly.
Link: https://lore.kernel.org/r/20230815190136.8987-13-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the rme96 driver code to use the new unified PCM
copy callback. It's a straightforward conversion from *_user() to
*_iter() variants.
Link: https://lore.kernel.org/r/20230815190136.8987-12-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the rme32 driver code to use the new unified PCM
copy callback. It's a straightforward conversion from *_user() to
*_iter() variants.
Link: https://lore.kernel.org/r/20230815190136.8987-11-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the nm256 driver code to use the new unified PCM
copy callback. It's a straightforward conversion from *_user() to
*_iter() variants.
Link: https://lore.kernel.org/r/20230815190136.8987-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the korg1212 driver code to use the new unified
PCM copy callback. The open-coded conditional memory copies are
replaced with simpler copy_from/to_iter() calls.
Note that copy_from/to_iter() returns the copied bytes, hence the
error condition is adjusted accordingly.
Link: https://lore.kernel.org/r/20230815190136.8987-9-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the es1938 driver code to use the new unified PCM
copy callback. It's a straightforward conversion from *_user() to
*_iter() variants in most parts.
Note that copy_from/to_iter() returns the copied bytes, hence the
error condition is adjusted accordingly.
Link: https://lore.kernel.org/r/20230815190136.8987-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Create tas2781 side codec HDA driver for Lenovo Laptops. The quantity
of the speakers has been define in ACPI. All of the tas2781s in the
laptop will be aggregated as one audio speaker. The code supports
realtek codec as the primary codec. Code offers several controls for
digtial/analog gain setting during playback, and other for eq params
setting in case of different audio profiles, such as music, voice,
movie, etc.
[ adjusted patch to be applied to the latest for-next branch -- tiwai ]
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://lore.kernel.org/r/20230818085836.1442-2-shenghao-ding@ti.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Integrate tas2781 configs for Lenovo Laptops. All of the tas2781s in the
laptop will be aggregated as one audio device. The code support realtek
as the primary codec. Rename "struct cs35l41_dev_name" to
"struct scodec_dev_name" for all other side codecs instead of the certain
one.
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://lore.kernel.org/r/20230818085836.1442-1-shenghao-ding@ti.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like control and PCM devices, it's better to avoid the embedded struct
device for hwdep (although it's more or less well working), too.
Change it to allocate via snd_device_alloc(), and free the memory at
the common snd_hwdep_free().
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Tested-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20230816160252.23396-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
cs35l41_prop_model is only used in cs35l41_hda_property.c now,
change it to static.
Fixes: ef4ba63f12 ("ALSA: hda: cs35l41: Support systems with missing _DSD properties")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20230817014252.1511232-1-yangyingliang@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set spec->en_3kpull_low default to true.
Then fillback ALC236 and ALC257 to false.
Additional note: this addresses a regression caused by the previous
fix 69ea4c9d02 ("ALSA: hda/realtek - remove 3k pull low procedure").
The previous workaround was applied too widely without necessity,
which resulted in the pop noise at PM again. This patch corrects the
condition and restores the old behavior for the devices that don't
suffer from the original problem.
Fixes: 69ea4c9d02 ("ALSA: hda/realtek - remove 3k pull low procedure")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217732
Link: https://lore.kernel.org/r/01e212a538fc407ca6edd10b81ff7b05@realtek.com
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some systems using CS35L41 with HDA were released without some
required _DSD properties in ACPI. To support these special cases,
add an api to configure the correct properties for systems with
this issue.
This initial commit moves the no _DSD support for Lenovo
Legion Laptops (CLSA0100, CLSA0101) into a new framework which
can be extended to support additional laptops in the future.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230815161033.3519-1-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
All I2C Dell Oasis models using CS35L41 have been changed to use SPI.
In addition, System 10280cc5 is no longer required.
Fixes: de90f5165b ("ALSA: hda/realtek: Add support for DELL Oasis 13/14/16 laptops")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230809142957.675933-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These HP G11 laptops use Realtek HDA codec combined with
2xCS35L41 Amplifiers using SPI or I2C with External Boost.
Laptop 103c8c26 has been removed as this has been replaced
by this new series of laptops.
Fixes: 3e10f6ca76 ("ALSA: hda/realtek: Add quirk for HP EliteBook G10 laptops")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230809142957.675933-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
`strncpy` is deprecated for use on NUL-terminated destination strings [1].
A suitable replacement is `strscpy` [2] due to the fact that it
guarantees NUL-termination on its destination buffer argument which is
_not_ the case for `strncpy`!
It should be noted that the current implementation is unlikely to have a
bug because `drv_name` is a string literal with a size of 9 while
`card->driver` has a size of 16. However, it is probably worthwhile to
switch to a more robust and less ambiguous interface.
[1]: www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings
[2]: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html
Link: https://github.com/KSPP/linux/issues/90
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Justin Stitt <justinstitt@google.com>
Link: https://lore.kernel.org/r/20230807-sound-pci-hda-v1-1-6d9cdcd085ca@google.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Print amp configuration information to be able to confirm ACPI
_DSD information (and other useful info) for each amp on each
system using CS35L41, without having to get the acpidump.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230802121235.467358-1-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ACPI nodes for CS35L56 can contain an extra I2CSerialBusV2 that
is not a real device, it is an alias address.
This alias address will not be in the cirrus,dev-index array, so reject
any instantions with a device address not found in the array.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-10-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A tuning patch is always needed to enable the ASP audio port.
If the BIOS did not patch the firmware, then it is mandatory to
have a .bin file.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-9-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A RAM firmware can only be downloaded if the CS35L56 is currently
running from ROM firmware. The driver must not try to overwrite
the RAM if the CS35L56 is already running from that RAM.
Firmware can be downloaded in these two cases:
- The BIOS has already patched the firmware (secured mode).
In this case the firmware files will only contain tunings that
are safe to overwrite.
- The CS35L56 is running the built-in ROM firmware.
After a RAM firmware has been downloaded it can only be cleared by
hard resetting CS35L56. Some systems only hard-reset during
power-on and do not give the driver control of hard reset.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-8-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If cs35l56_hda_fw_load() successfully called cs_dsp_power_up() the error
path must balance that with a call to cs_dsp_power_down().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-7-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In cs35l56_hda_unbind() cs_dsp_power_down() must be called to cleanup
before calling cs_dsp_remove cs_dsp_remove().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-6-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Always call cs_dsp_power_up() and cs_dsp_run() in
cs35l56_hda_fw_load() even if there aren't any firmware files
to download. Also, if there aren't any firmware files to
download there is no need to do cs35l56_firmware_shutdown() and
cs35l56_system_reset().
If there aren't any firmware files there's no need to write
anything to the CS35L56 registers to make it work - it will
already be running the ROM firmware. So it's not strictly
necessary to start cs_dsp.
But it's perfectly ok to call cs_dsp_power_up() and
cs_dsp_run() without downloading any firmware. This avoids
having to support a state where audio is playing but cs_dsp
is not running.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-5-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When firmware is reloaded after a system resume cs_dsp_power_down() should
be called before calling cs_dsp_power_up().
The fw_patched flag should also be cleared and only set again if the
firmware download succeeded.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-4-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Only call regcache_mark_dirty() in cs35l56_hda_fw_load() if
the CS35L56 was SYSTEM_RESET.
recache_mark_dirty() changes the behaviour of regcache_sync()
to write out cache values that are not the default value, and
skip cache values that are the default.
AUDIO_REINIT does not reset the registers. regcache_mark_dirty()
after AUDIO_REINIT could cause the regcache_sync() to sync
registers incorrectly because it will assume that all registers
have reset to default.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-3-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the call to cs_dsp_run() in cs35l56_hda_fw_load() so that it
is after the CS35L56 has been reset/reinit'd and the regmap
cache has been synced.
cs_dsp_run() syncs up ALSA control cache values with the DSP memory
so this must not be done until the firmware has reinitialized.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-2-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Smatch complains that this return should be a goto:
sound/pci/hda/cs35l56_hda.c:910 cs35l56_hda_common_probe()
warn: missing unwind goto?
The goto error disables cansleep so that seems reasonable.
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/465160f4-b7cf-41d5-931e-d6c9e68fa3c7@moroto.mountain
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This laptop has CS35L41 amp connected via I2C.
With this patch speakers begin to work if the
missing _DSD properties are added to ACPI tables.
Signed-off-by: Pavel Asyutchenko <svenpavel@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230726223732.20775-1-svenpavel@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This HP Notebook used ALC236 codec with COEF 0x07 idx 1 controlling
the mute LED. Enable already existing quirk for this device.
Signed-off-by: Luka Guzenko <l.guzenko@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230725111509.623773-1-l.guzenko@web.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here's an initial batch of updates for ASoC for this release cycle.
We've got a bunch of new drivers in here, a bit of core work from
Morimoto-san and quite a lot of janitorial work. There's several
updates that pull in changes from other subsystems in order to build
on them:
- An adaptor to allow use of IIO DACs and ADCs in ASoC which pulls in
some IIO changes.
- Create a library function for intlog10() and use it in the NAU8825
driver.
- Include the ASoC tests, including the topology tests, in the default
KUnit full test coverage. This also involves enabling UML builds of
ALSA since that's the default KUnit test environment which pulls in
the addition of some stubs to the driver.
- More factoring out from Morimoto-san.
- Convert a lot of drivers to use the more modern maple tree register
cache.
- Support for AMD machines with MAX98388 and NAU8821, Cirrus Logic
CS35L36, Intel AVS machines with ES8336 and RT5663 and NXP i.MX93.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmS/t9MACgkQJNaLcl1U
h9Dg4wf+Njvy5zphgUJlSJ7vNj7GtzgldnWwfQrb+19BOtv5HHIYg4e/Yr4eWdgc
rg5DGIGvr8sxYQ44TCA59sXdTuakkNF/ejDoj8AwNsr/J3sD6S+FTkV8qLFcgQ3r
+0ElZ26I2kd6gfvDlwHfa5rJVPCa7vrg3o6EHccqRX9CSyPJRlwRqRRj+w8ftZtV
rZ7Gapz3E4A3mBo7VIO/kEgI1uSmaShM8d4HoVmxJEKJ6lbyX8SIXMBzZVq5z/iX
DcnRaMPAMhgzytmdDJ7SjJuxL0EOd6p8Lnk0jILvO6U30Z7aTunzMuK/o0GHqFkm
eHveoHIU4gbt3YqDFgPosPlxi4OCgw==
=KJZq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v6.6-early' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v6.6
Here's an initial batch of updates for ASoC for this release cycle.
We've got a bunch of new drivers in here, a bit of core work from
Morimoto-san and quite a lot of janitorial work. There's several
updates that pull in changes from other subsystems in order to build
on them:
- An adaptor to allow use of IIO DACs and ADCs in ASoC which pulls in
some IIO changes.
- Create a library function for intlog10() and use it in the NAU8825
driver.
- Include the ASoC tests, including the topology tests, in the default
KUnit full test coverage. This also involves enabling UML builds of
ALSA since that's the default KUnit test environment which pulls in
the addition of some stubs to the driver.
- More factoring out from Morimoto-san.
- Convert a lot of drivers to use the more modern maple tree register
cache.
- Support for AMD machines with MAX98388 and NAU8821, Cirrus Logic
CS35L36, Intel AVS machines with ES8336 and RT5663 and NXP i.MX93.
Currently we only mute after playback has finished, and unmute
prior to setting global enable. To prevent any possible pops
and clicks, mute at probe, and then only unmute after global
enable is set.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-12-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To ensure consistency between the HDA core and the CS35L41 HDA
driver, add a device_link between them. This ensures that the
HDA core will suspend first, and resume second, meaning the
amp driver will not miss any events from the playback hook from
the HDA core during system suspend and resume.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-11-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to correctly pause audio on suspend, amps using external boost
require parts of the pause sequence to be called for all amps before moving
on to the next steps.
For example, as part of pausing the audio, the VSPK GPIO must be disabled,
but since this GPIO is controlled by one amp, but controls the boost for
all amps, it is required to separate the calls.
During playback this is achieved by using the pre and post playback hooks,
however during system suspend, this is not possible, so to separate the
calls, we use both the .prepare and .suspend calls to pause the audio.
Currently, for this reason, we do not restart audio on system resume.
However, we can support this by relying on the playback hook to resume
playback after system suspend.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-10-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use new hooks to ensure separation between play/pause actions,
as required by external boost.
External Boost on CS35L41 requires the amp to go through a
particular sequence of steps. One of these steps involes
the setting of a GPIO. This GPIO is connected to one or
more of the amps, and it may control the boost for all of
the amps. To ensure that the GPIO is set when it is safe
to do so, and to ensure that boost is ready for the rest of
the sequence to be able to continue, we must ensure that
the each part of the sequence is executed for each amp
before moving on to the next part of the sequence.
Some of the Play and Pause actions have moved from Open to
Prepare. This is because Open is not guaranteed to be called
again on system resume, whereas Prepare should.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-9-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These hooks can be used to add callbacks that would be run before and after
the main playback hooks. These hooks would be called for all amps, before
moving on to the next hook, i.e. pre_playback_hook would be called for
all amps, before the playback_hook is called for all amps, then finally
the post_playback_hook is called for all amps.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-8-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are several steps required to put the system into system suspend.
Some of these steps may fail, so the driver should pass up the errors
if they occur.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-6-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to properly system suspend, it is necessary to unload the firmware
and ensure the chip is ready for shutdown (if necessary). If the system
is currently in runtime suspend, it is necessary to wake up the device,
and then make it ready. Currently, the wake does not correctly resync
the device, which may mean it cannot suspend correctly. Fix this by
performaing a resync.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-5-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, we do not check the return status of the pause command,
immediately after we load firmware. If the pause has failed,
the firmware is not running.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To enable the speaker output in external boost mode, 2 registers must
be set, one after another. The longer the time between the writes of
the two registers, the more likely, and more loudly a pop may occur.
To minimize this, an mbox command can be used to allow the firmware
to perform this action, minimizing any delay between write, thus
minimizing any pop or click as a result. The old method will remain
when running without firmware.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a driver for the Cirrus Logic CS35L56 amplifier. This uses the same
component binding API as the CS35L41 driver. This is not a standalone
HDA device; it provides control of the CS35L56 for systems that use a
combination of an HDA codec and CS35L56 amplifiers with audio routed
through the HDA codec.
The CS35L56 combines a high-performance mono audio amplifier, Class-H
tracking inductive boost converter, Halo Core(TM) DSP and a DC-DC boost
converter supporting Class-H tracking.
Control interfaces are I2C or SPI through the standard Linux I2C or SPI
bus framework.
Most chip functionality is controlled by on-board ROM firmware that is
always running. Firmware patches can be applied by the driver in the form
of a .wmfw file (firmware patch) and/or a .bin file (system tuning).
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230721132120.5523-12-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add #includes of dependencies into hda_auto_parser.h and hda_generic.h
hda_auto_parser.h uses definitions in hda_local.h.
hda_generic.h uses definitions in hda_local.h and hda_auto_parser.h.
It also references struct hda_jack_callback, but only as a pointer.
This has been forward-declared so hda_jack.h only needs to be
included in source that actually uses it.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230721132120.5523-11-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch order of Intel MTL and RPL codec entries to keep the codec device
id list nicely ordered. Also use the opportunity to fix the naming
to the convention used elsewhere in the drivers.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230721135722.31288-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of open-code, use the new standard helper to manage vmaster
stuff for code simplification.
Also, handle the errors from the helper more properly instead of
silently ignoring.
The code changes the call order of snd_ctl_add() of the vmaster object
and its followers for avoiding the possible memory leaks at error
path. But there should be no difference in the functionality.
Link: https://lore.kernel.org/r/20230721071643.3631-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of open-code, use the new standard helper to manage vmaster
stuff for code simplification.
Also, handle the errors from the helper more properly instead of
silently ignoring.
Link: https://lore.kernel.org/r/20230721071643.3631-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of open-code, use the new standard helper to manage vmaster
stuff for code simplification.
Except for a debug print, there should be no functional change.
Link: https://lore.kernel.org/r/20230721071643.3631-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace an open code with the new snd_ctl_find_id_mixer().
There is no functional change.
Also, add the missing NULL checks in psc724_set_jack_state() to deal
with error cases.
Link: https://lore.kernel.org/r/20230720082108.31346-7-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adding support for new Dell laptops using Cirrus Logic CS35L41
smart amplifiers with Realtek codec.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230720082022.13033-2-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Generic fixup for CS35L41 amplifies should not have vendor specific
chained fixup. For ThinkPad laptops with led issue, we can just add
specific fixup.
Fixes: a6ac60b36d (ALSA: hda/realtek: Fix mute led issue on thinkpad with cs35l41 s-codec)
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230720082022.13033-1-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few ALSA control API helpers like snd_ctl_rename(), snd_ctl_remove()
and snd_ctl_find_*() suppose the callers taking card->controls_rwsem.
But it's error-prone and fragile. This patch set tries to change
those API functions to take the card->controls>rwsem internally by
themselves, so that the drivers don't need to take care of lockings.
After applying this patch set, only a couple of places still touch
card->controls_rwsem (which are OK-ish as they need for traversing the
control linked list).
Link: https://lore.kernel.org/r/20230718141304.1032-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAmS46rUOHHRpd2FpQHN1
c2UuZGUACgkQLtJE4w1nLE8tZRAAh24GODlDoY+KWCEo9ENkzUssWkfat174A5xE
NJvW1N7cP7NeN8lQUbqvfB5DLTulBDb9RS0s42RcuqOt7/uKDlTV9Nx0exgyXINC
Xxr5MaCsYuZxzCHy/9AxHchxgcksMkDVxugIQ4RmOhfof3lRA9O3OxLIdE+aHYhQ
UOtrqnsoXlZXWjbi3OaT1KE2ilAXE/5f2P+fgoQ09ZQwyxAu43izeCkWJpBtWDuF
/bHftmwXvHOIgiggeSJ0S0zrCPX5cPYzIcYusyucwyztj7CYIwGMyBncGw8ucyUr
TjNhxQIZNDEyE3w0mre4X8rB3JLPlqaszqLKu6GsX8dwoAle5t1LPeG/6RhZxnD1
o6D9/HCu9VdVSSDFlQ87SZH81SV0ltqHFqUFX5XroAhYyBG9xe/z29AU5p2Qx2B4
saR/la384Bxedu/QpBM7pkqDZceKy4iNIGKVZXKu+1yd8Q5xbHNguU/RlXLM83iX
/mcnO7/SDfI9m+hSgEXUZEl1pBW7wOWnTATAfjbr4ANNSwgzoVyS8a/86g3QjdvJ
SlHysXDP+w5nf5QZd4wTMzKo6wjD5EMLie0FTCF9QvD5IMtAwVqTHYYoJDW85Qr0
gxovfYqjhZ05Aa87S+Gy154HUwLhRfhOaQp7wBpuHwlmYcFhw+0RnF6/RbZGEjMv
VvP4PQ8=
=V5+5
-----END PGP SIGNATURE-----
Merge tag 'tags/ctl-lock-fixes-6.6' into for-next
ALSA: Make control API taking controls_rwsem consistently
A few ALSA control API helpers like snd_ctl_rename(), snd_ctl_remove()
and snd_ctl_find_*() suppose the callers taking card->controls_rwsem.
But it's error-prone and fragile. This patch set tries to change
those API functions to take the card->controls>rwsem internally by
themselves, so that the drivers don't need to take care of lockings.
After applying this patch set, only a couple of places still touch
card->controls_rwsem (which are OK-ish as they need for traversing the
control linked list).
Link: https://lore.kernel.org/r/20230718141304.1032-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that snd_ctl_find_id() takes the locking itself, we can get rid of
the messy locking in the caller side in snd_emu10k1_verify_controls().
Link: https://lore.kernel.org/r/20230718141304.1032-12-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For reducing the unnecessary use of controls_rwsem in the drivers,
this patch adds a new variant for snd_ctl_find_*() helpers:
snd_ctl_find_id_locked() and snd_ctl_find_numid_locked() look for a
kctl element inside the card->controls_rwsem -- that is, doing the
very same as what snd_ctl_find_id() and snd_ctl_find_numid() did until
now. snd_ctl_find_id() and snd_ctl_find_numid() remain same,
i.e. still unlocked version, but they will be switched to locked
version once after all callers are replaced.
The patch also replaces the calls of snd_ctl_find_id() and
snd_ctl_find_numid() in a few places; all of those are places where we
know that the functions are called properly with controls_rwsem held.
All others are without rwsem (although they should have been).
After this patch, we'll turn on the locking in snd_ctl_find_id() and
snd_ctl_find_numid() to be more race-free.
Link: https://lore.kernel.org/r/20230718141304.1032-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, snd_ctl_remove() requires its caller to take
card->controls_rwsem manually before the call for avoiding possible
races. However, many callers don't care and miss the locking.
Basically it's cumbersome and error-prone to enforce it to each
caller. Moreover, card->controls_rwsem is a field that should be used
only by internal or proper helpers, and it's not to be touched at
random external places.
This patch is an attempt to make those calls more consistent: now
snd_ctl_remove() takes the card->controls_rwsem internally, just like
other API functions for kctls. Since a few callers already take the
controls_rwsem locks, the patch removes those locks at the same time,
too.
Link: https://lore.kernel.org/r/20230718141304.1032-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP Laptop 15s-eq2xxx uses ALC236 codec and controls the mute LED using
COEF 0x07 index 1. No existing quirk covers this configuration.
Adds a new quirk and enables it for the device.
Signed-off-by: Luka Guzenko <l.guzenko@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230718161241.393181-1-l.guzenko@web.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use PCI device IDs from pci_ids.h header and while at it to simplify
declarations change to using PCI_DEVICE_DATA() macro for Intel IDs and
PCI_VDEVICE() for all other that have defined vendor.
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230717114511.484999-11-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of using local macro to match PCI device, use global one. As
Apollolake is Broxton-P successor that made it to the market, be precise
and use APL shortcut.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230717114511.484999-7-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current code references 0x1a98 which is BXT-M (not -T as it is
commented) and it's an RVP, BXT-M B0 to be specific. From what we know
no BXT is available on market.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230717114511.484999-5-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Remove the "log-like" parts, following the same logic as the previous
commit
- Unify format
- Add missing major contributors, including myself
- Sort entries in order of first contribution (Creative comes last for
optical reasons; they don't appear to have directly contributed
anyway)
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230715160839.326978-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Empty BUGS and TODO sections don't really help anyone, so remove them.
Version information is chronically outdated, and not really useful in a
git world anyway, so remove it as well.
Also remove duplicated (and outdated, of course) status section from
p16v.h (the one in p16v.c is in better shape).
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230715160839.326978-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
85;95;0c
This uses IRQs to track spontaneous changes to the word clock source
register.
FWIW, that this can happen in the first place is the reason why it is
futile to lock the clock source mixer setting while the device is open -
we can't consistently control the rate anyway. Though arguably, we
should reset any open streams when that happens, as they become
corrupted anyway.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230715160738.326832-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230714175109.4066599-1-robh@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This was the ALC283 depop procedure.
Maybe this procedure wasn't suitable with new codec.
So, let us remove it. But HP 15z-fc000 must do 3k pull low. If it
reboot with plugged headset,
it will have errors show don't find codec error messages. Run 3k pull
low will solve issues.
So, let AMD chipset will run this for workarround.
Fixes: 5aec989130 ("ALSA: hda/realtek - ALC236 headset MIC recording issue")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Reported-by: Joseph C. Sible <josephcsible@gmail.com>
Closes: https://lore.kernel.org/r/CABpewhE4REgn9RJZduuEU6Z_ijXNeQWnrxO1tg70Gkw=F8qNYg@mail.gmail.com/
Link: https://lore.kernel.org/r/4678992299664babac4403d9978e7ba7@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mixer, PCM prepare, MIDI, synth driver, and procfs callbacks are all
always invoked with IRQs enabled, so there is no point in saving the
state.
snd_emu1010_load_firmware_entry() is called from emu1010_firmware_work()
and snd_emu10k1_emu1010_init(); the latter from snd_emu10k1_create() and
snd_emu10k1_resume(), all of which have IRQs enabled.
The voice and memory functions are called from mixed contexts, so they
keep the state saving.
The low-level functions all keep the state saving, because it's not
feasible to keep track of what is called where.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230712145750.125086-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds the required quirk to enable the Cirrus amp and correct pins
on the ASUS ROG GZ301V series which uses an SPI connected Cirrus amp.
While this works if the related _DSD properties are made available, these
aren't included in the ACPI of these laptops (yet).
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Link: https://lore.kernel.org/r/20230706223323.30871-2-luke@ljones.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds the required quirk to enable the Cirrus amp and correct pins
on the ASUS ROG G614J series which uses an SPI connected Cirrus amp.
While this works if the related _DSD properties are made available, these
aren't included in the ACPI of these laptops (yet).
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Link: https://lore.kernel.org/r/20230704044619.19343-5-luke@ljones.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds the required quirk to enable the Cirrus amp and correct pins
on the ASUS ROG GA402X series which uses an I2C connected Cirrus amp.
While this works if the related _DSD properties are made available, these
aren't included in the ACPI of these laptops (yet).
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Link: https://lore.kernel.org/r/20230704044619.19343-3-luke@ljones.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds the required quirk to enable the Cirrus amp and correct pins
on the ASUS ROG GV601V series which uses an I2C connected Cirrus amp.
While this works if the related _DSD properties are made available, these
aren't included in the ACPI of these laptops (yet).
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Link: https://lore.kernel.org/r/20230704044619.19343-2-luke@ljones.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These models use NSIWAY amplifiers for internal speaker, but cannot put
sound outside from these amplifiers. So eapd verbs are needed to initialize
the amplifiers. They can be added during boot to get working sound out
of internal speaker.
Signed-off-by: dengxiang <dengxiang@nfschina.com>
Link: https://lore.kernel.org/r/20230703021751.2945750-1-dengxiang@nfschina.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This applies a SND_PCI_QUIRK(...) to the Clevo NPx0SNx barebones fixing the
microphone not being detected on the headset combo port.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230628155434.584159-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A fairly quiet release from a core and framework point of view, but a
very big one from the point of view of new drivers:
- More refectoring from Morimoto-san, this time mainly around DAI
links and how we control the ordering of trigger() callbacks.
- Convert a lot of drivers to use maple tree based caches.
- Lots of work on the x86 driver stack.
- Compressed audio support for Qualcomm.
- Support for AMD SoundWire, Analog Devices SSM3515, Google Chameleon,
Ingenic X1000, Intel systems with various CODECs, Longsoon platforms,
Maxim MAX98388, Mediatek MT8188, Nuvoton NAU8825C, NXP platforms with
NAU8822, Qualcomm WSA884x, StarFive JH7110, Texas Instruments TAS2781.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmSZjIQACgkQJNaLcl1U
h9Dm0wf/X1q4n6KSXLvSyoSUxS/RWzWgyDDX7a4iLcFiov3ehHpVwzhwI/+1xSzs
SGhg6q2rud05SejFBh+2L7HMZfdXWSfW9ukaGz3UsCdqw3/7zAUFgY1RGtjZO4lA
eH50vEME9RbkIDgyxzYe9eViaKGh2fNxIbQ2d9hx6+nIVNfuuSikvGz4K/9PD0DN
2tBgzuIWwrPIbvMV2zHDCycmVG0lqScMWjIrdpDFxa63aPTr920YqYWSoQfOUR1s
j9zlZWnclTjrqRl1GZHxnM8N70vmutZWXAB1WFjal6mmMd6lUG71CyYHvA5h5D0V
ygNpn9B5REYlHBVzI43uT3nog+iS4Q==
=dbjW
-----END PGP SIGNATURE-----
Merge tag 'asoc-v6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v6.5
A fairly quiet release from a core and framework point of view, but a
very big one from the point of view of new drivers:
- More refectoring from Morimoto-san, this time mainly around DAI
links and how we control the ordering of trigger() callbacks.
- Convert a lot of drivers to use maple tree based caches.
- Lots of work on the x86 driver stack.
- Compressed audio support for Qualcomm.
- Support for AMD SoundWire, Analog Devices SSM3515, Google Chameleon,
Ingenic X1000, Intel systems with various CODECs, Longsoon platforms,
Maxim MAX98388, Mediatek MT8188, Nuvoton NAU8825C, NXP platforms with
NAU8822, Qualcomm WSA884x, StarFive JH7110, Texas Instruments TAS2781.
On HP EliteBook 835/845/845W G10, the audio LEDs can be enabled by
ALC285_FIXUP_HP_MUTE_LED. So use it accordingly.
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Fixes: 3e10f6ca76 ("ALSA: hda/realtek: Add quirk for HP EliteBook G10 laptops")
Link: https://lore.kernel.org/r/20230626130301.301712-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds the required quirk to enable the Cirrus amp and correct pins
on the ASUS ROG GV601V series.
While this works if the related _DSD properties are made available, these
aren't included in the ACPI of these laptops (yet).
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Link: https://lore.kernel.org/r/20230621085715.5382-1-luke@ljones.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds the required quirk to enable the Cirrus amp and correct pins
on the ASUS ROG G634Z series.
While this works if the related _DSD properties are made available, these
aren't included in the ACPI of these laptops (yet).
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Link: https://lore.kernel.org/r/20230619060320.1336455-1-luke@ljones.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
smatch error:
sound/pci/ac97/ac97_codec.c:2354 snd_ac97_mixer() error:
we previously assumed 'rac97' could be null (see line 2072)
remove redundant assignment, return error if rac97 is NULL.
Fixes: da3cec35dd ("ALSA: Kill snd_assert() in sound/pci/*")
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20230615021732.1972194-1-suhui@nfschina.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The file is called spdif-in, but we abused it to show only sample rates
from various sources. Rectify it as far as possible (the FPGA doesn't
give us a lot of information).
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230612191325.1315854-10-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is only a very partial fix - the frequency-dependent envelope & LFO
register values aren't adjusted.
But I'm not sure they were even correct at 48 kHz to start with, as most
of them are precalculated by common code which assumes an EMU8K-specific
44.1 kHz word clock, and it seems somewhat unlikely that the hardware's
register interpretation was adjusted to compensate for the different
word clock.
In any case I'm not going to spend time on fixing that, as this code is
unlikely to be actually used by anyone today.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230612191325.1315854-6-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that we know the actual word clock, we can:
- Put the resulting rate into the hardware info
- At 44.1 kHz word clock shift the rate for the pitch calculations,
which presume a 48 kHz word clock
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230612191325.1315854-5-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The value isn't used yet; the subsequent commits will do that.
This ignores the existence of rates above 48 kHz, which is fine, as the
hardware will just switch to the fallback clock source when fed with a
rate which is incompatible with the base clock multiplier, which
currently is always x1.
The sample rate display in /proc spdif-in is adjusted to reflect our
understanding of the input rates.
This is tested only with an 0404b card without sync card, so there is a
lot of room for improvement.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230612191325.1315854-4-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The actually available clock sources depend on the available audio input
ports and dedicated clock input ports.
This includes refactoring the code to be data-driven to remain
manageable.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230612191325.1315854-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, we set the fallback as a side effect of setting the source. But
the fallback makes no sense at all when an internal clock is selected.
Defaulting to 48k for S/PDIF & ADAT makes sense, but as that is the
global default and we're not changing it automatically any more, it's
just fine to leave it entirely to the explicit setting.
This changes the name of the pre-existing control to something more
appropriate (regardless of the split), so users will need to adjust
their mixer settings.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230612191325.1315854-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On loongson controller, the value of WALLCLK register
is always 0, which is meaningless, so we return directly.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Signed-off-by: Yingkun Meng <mengyingkun@loongson.cn>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/185df71ef413ab190460eb377703214ee7288aeb.1686128807.git.siyanteng@loongson.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On loongson controller, after calling snd_hdac_stream_updateb()
to enable DMA engine, the SDnCTL.STRM will become to zero. We
need to access SDnCTL in dword to keep SDnCTL.STRM is not changed.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Signed-off-by: Yingkun Meng <mengyingkun@loongson.cn>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/27aeddf5ebbe7c69631cec0e489c1b264be94990.1686128807.git.siyanteng@loongson.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On loongson controller, RIRBSTS.RINTFL cannot be cleared,
azx_interrupt() is called all the time. We disable RIRB
interrupt, and use polling mode by default.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Signed-off-by: Yingkun Meng <mengyingkun@loongson.cn>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/d309a75424d438b958d90d797b4f1ba45468e090.1686128807.git.siyanteng@loongson.cn
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the commit 7bb6234095 ("ALSA: hda/realtek: fix speaker, mute/micmute
LEDs not work on a HP platform"), speakers and LEDs are fixed but only 2
CS35L41 amplifiers on SPI bus connected to Realtek codec are enabled. Need
the ALC245_FIXUP_CS35L41_SPI_4_HP_GPIO_LED to get all amplifiers working.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
Fixes: 7bb6234095 ("ALSA: hda/realtek: fix speaker, mute/micmute LEDs not work on a HP platform")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230606145747.135966-1-chris.chiu@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ensure Firmware Load control and Firmware Type control
returns 1 when the value changes.
Remove fw_mutex from firmware load control put, since it is
unnecessary, and prevents any possibility of mutex inversion.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230606103436.455348-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HD-audio core code replaces the kctl->id.index of SPDIF-related
controls after assigning via snd_ctl_add(). This doesn't work any
longer with the new Xarray lookup change. The change of the kctl->id
content has to be done via snd_ctl_rename_id() helper, instead.
Fixes: c27e1efb61 ("ALSA: control: Use xarray for faster lookups")
Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230606093855.14685-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
cmipci driver replaces the kctl->id.device after assigning the kctl
via snd_ctl_add(). This doesn't work any longer with the new Xarray
lookup change. It has to be set before snd_ctl_add() call instead.
Fixes: c27e1efb61 ("ALSA: control: Use xarray for faster lookups")
Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230606093855.14685-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ymfpci driver replaces the kctl->id.device after assigning the kctl
via snd_ctl_add(). This doesn't work any longer with the new Xarray
lookup change. It has to be set before snd_ctl_add() call instead.
Fixes: c27e1efb61 ("ALSA: control: Use xarray for faster lookups")
Cc: <stable@vger.kernel.org>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230606093855.14685-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The new xarray lookup code requires to know complete kcontrol->id before
snd_ctl_add() call. Reorder the code to make the initialization properly.
Cc: stable@kernel.org # v5.19+
Reported-by: Martin Zidek <zidek@master.cz>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230606073122.597491-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Headset microphone on this platform does not work without
ALC897_FIXUP_HEADSET_MIC_PIN fixup.
Signed-off-by: RenHai <kean0048@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230602003604.975892-1-kean0048@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Include the FX bus map, without which the already present send routing
info would require looking up the documentation.
- Include the physical I/O channels as known to the driver
- Make the multi-channel capture map actually name the mapped input
channels rather than "FXBUS" (Audigy) or even "???" (SbLive)
- The latter two are omitted for E-MU cards, as their physical I/O is
routed through the FPGA
- While at it, make the "Card" field somewhat more useful
This includes de-duplicating the label tables between emuproc and emufx,
updating/improving the FX bus label table, and making the SB Live! 5.1
multi-track capture channel mapping hack data-driven.
Tested-by: Jonathan Dowland <jon@dow.land>
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230526101659.437969-7-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Include the routing information, which can be actually read back.
Somewhat as a drive-by, make the register dump format less obscure - the
previous one made no sense at all.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230526101659.437969-6-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It seems to make little sense to include the FX send routing, but not
the amounts.
This also simplifies the code somewhat, and lines up the output.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230526101659.437969-5-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The limits were appropriate only for the 2nd set.
FWIW, the channel count 4 for the 2nd set is suspicious as well - at
least P17V_PLAYBACK_FIFO_PTR actually has 8 channels, and comments on
HCFG2 hint at that as well. But all bitmasks are documented only for 4
channels. Anyway, rectifying that is out of scope for this patch.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230526101659.437969-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The 2nd register set belongs to the P16V chip (or embedded P17V module),
so there is nothing to show when no such part is present. Gen2 E-MU
cards have a P17V, but it's entirely unused, so we hide it there as
well.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230526101659.437969-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://lore.kernel.org/r/20230525203640.677826-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Cristian Ciocaltea <cristian.ciocaltea@collabora.com>:
This patch series handles a few issues related to the ES8316 audio
codec, discovered while doing some testing on the Rock 5B board.
Lenovo M70/M90 Gen4 are equipped with ALC897, and they need
ALC897_FIXUP_HEADSET_MIC_PIN quirk to make its headset mic work.
The previous quirk for M70/M90 is for Gen3.
Signed-off-by: Bin Li <bin.li@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230524113755.1346928-1-bin.li@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On SB cards the number of captured channels is derived from the voice
mask mixer control. But for E-MU cards this wasn't actually "wired up",
so changing the mask would simply mess up the recording.
We could fix that, but the channel routing through the FPGA makes the
masking redundant. So instead we hide the control, and let the user
specify the PCM channel count the traditional way.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523200709.236059-5-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hardware can deal with primes up to 7 and power-of-two multiples
thereof; the limitation is reflected by the possible buffer sizes.
Note that setting the voice mask will not allow more than 16 channels
even on Sound Blaster Audigy anymore, as 32 seems a bit excessive (the
code overall appears to think so, just not in this case).
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523200709.236059-4-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We need to specify that the hardware supports non-standard rates, as
otherwise the sound core creates a constraint which limits the rate to
the specified standard rates. That also made the rate constraint we were
already adding meaningless.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523200709.236059-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The buffer size register sets the size of the whole buffer, not just one
period. We actually handled it like that, except that the constraint was
set on the wrong parameter. The period size is implicitly constrained by
the buffer size and the fixed period count of 2.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523200709.236059-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We use independent voices for the channels, so we need to make an effort
to ensure that they are actually in sync.
The hardware doesn't provide atomicity, so we may need to retry a few
times, due to NMIs, PCI contention, and the wrong phase of the moon.
Solution inspired by kX-project.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523200709.236023-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For unclear reasons, the extra voice was set up with half the buffer
size instead of the period size. Commit 27ae958cf6 ("emu10k1 driver -
add multichannel device hw:x,3 [2-8/8]") mentions half-loop interrupts,
so maybe this was an artifact of an earlier iteration of the patch.
While at it, also fix periods_min of the regular playback - one period
makes just no sense.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523200709.236023-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Do not include pm_runtime.h header in files where APIs exported by
pm_runtime.h are not used.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com> # for omap-mcbsp-st.c
Link: https://lore.kernel.org/r/20230517094903.2895238-2-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
... instead of passing in a high-level mixer struct. Let the
higher-level functions handle the differences between the voice types.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523104612.198884-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds snd_emu10k1_pcm_init_{voices,extra_voice}() and
snd_emu10k1_playback_{un,}mute_voices() to slightly abstract by voice
function and potential stereo property.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230523104612.198884-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230522105049.1467313-33-schnelle@linux.ibm.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
One-element arrays are deprecated, and we are replacing them with flexible
array members instead. However, in this case it seems those one-element
arrays have never actually been used as fake flexible arrays.
See this code that dates from Linux-2.6.12-rc2 initial git repository build
(commit 1da177e4c3 ("Linux-2.6.12-rc2")):
sound/pci/mixart/mixart_core.h:
215 struct mixart_stream_state_req
216 {
217 u32 delayed;
218 u64 scheduler;
219 u32 reserved4np[3];
220 u32 stream_count; /* set to 1 for instance */
221 struct mixart_flow_info stream_info; /* could be an array[stream_count] */
222 } __attribute__((packed));
sound/pci/mixart/mixart.c:
388
389 memset(&stream_state_req, 0, sizeof(stream_state_req));
390 stream_state_req.stream_count = 1;
391 stream_state_req.stream_info.stream_desc.uid_pipe = stream->pipe->group_uid;
392 stream_state_req.stream_info.stream_desc.stream_idx = stream->substream->number;
393
So, taking the code above as example, replace multiple one-element
arrays with simple object declarations, and refactor the rest of the
code, accordingly.
This helps with the ongoing efforts to tighten the FORTIFY_SOURCE
routines on memcpy() and help us make progress towards globally
enabling -fstrict-flex-arrays=3 [1].
This results in no differences in binary output.
Link: https://github.com/KSPP/linux/issues/79
Link: https://github.com/KSPP/linux/issues/296
Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/ZGfiFjcL8+r3mayq@work
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of separate voices, we now allocate non-interleaved channels,
which may in turn contain two interleaved voices each. The higher-level
code keeps only one pointer per channel. The channels are not allocated
in one block any more, as there is no reason to do that. As a
consequence of that, and because it is cleaner regardless, we now let
the allocator store these pointers at a specified location, rather than
returning only the first one and having the calling code deduce the
remaining ones.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518140947.3725394-8-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The voice allocator clearly knows about the field (it resets it), so
it's more consistent (and leads to less duplicated code) to have the
constructor take it as a parameter.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518140947.3725394-7-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This allows us to drop the code that tries to preserve already allocated
voices upon repeated hw_param callback invocations. Getting it right for
multi-channel voices would otherwise get a bit hairy.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518140947.3725394-5-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Eliminate the MIDI type, as there is no such thing - the MPU401 port
doesn't have anything to do with voices.
For clarity, differentiate between regular and extra voices.
Don't atomize the enum into bits in the table display.
Simplify/optimize the storage.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518140947.3725394-4-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The subsequent allocation may still fail after freeing some voices, so
we shouldn't leave them in their programmed state.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518140947.3725394-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On Audigy, the send amounts are merely targets, presumably to avoid
sound distortion due to sudden changes, which the EMU8K docu explicitly
warns about.
However, that "soft-start" would prevent bit-for-bit reproduction, so
we now force the current send amounts to their final values at PCM
playback init.
One might want to do that for the MIDI synthesizer as well, though it
seems mostly pointless due to the attack phase each note has anyway.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518140339.3722279-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CPF_CURRENTPITCH starts swerving towards PTRX_PITCHTARGET as soon as
that is set. In practice this means that CPF_FRACADDRESS may acquire a
non-zero value before we manage to force CPF_CURRENTPITCH to the final
value, which would prevent bit-for-bit reproduction.
To avoid that this state persists, we now reset CPF_FRACADDRESS when
setting CPF_CURRENTPITCH, and to (mostly) avoid that it progresses too
far in the first place (possibly even reaching CCCA_CURRADDR), we write
PTRX and CPF in one critical section (though NMIs, etc. still make this
unreliable).
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518140339.3722279-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make terminate_voice() actually do at all what it's supposed to do:
instantly and completely shut down the note.
The bogus behavior was mostly harmless, as usually the voice is freed
right afterwards, which implicitly terminates it anyway.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518140339.3722308-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Compensate for the cache delay, and actually populate the cache.
Without these, the playback would start with garbage (which would be
(mostly?) masqueraded by the attack phase).
Unlike for the PCM voices, this doesn't try to compensate for the
interpolator read-ahead, because it's pointless to be super-exact here.
Note that this code is probably still broken for particularly short
samples, because we ignore the loop-related parts of CCR. But I'm not
going to reverse-engineer that now ...
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518140339.3722308-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
smatch reports
sound/pci/emu10k1/emumixer.c:519:39: warning: symbol
'emu1010_routing_info' was not declared. Should it be static?
sound/pci/emu10k1/emumixer.c:859:36: warning: symbol
'emu1010_pads_info' was not declared. Should it be static?
These variables are only used in their defining file, so it should be static
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518123826.925752-1-trix@redhat.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While this nicely denoises the code, the real intent is being able to
write many registers pseudo-atomically, which will come in handy later.
Idea stolen from kX-project.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518093134.3697955-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We'd try to iterate the voices twice without resetting the pointer.
This went unnoticed, because the code isn't actually in use.
Amends commit 27ae958cf6 ("emu10k1 driver - add multichannel device
hw:x,3 [2-8/8]").
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518093047.3697887-4-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Handle the "timeout" (actually the retry counter) such that it's more
obvious and causes less cost in the normal case.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518093047.3697887-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove weird INTE_* clearing code. The bits were a subset of the
actually handled interrupts, which kind of contradicted the stated
purpose. I suppose it would make sense to complete the set and negate
it, but interrupts being enabled out of the blue is neither something
that happens a lot, nor should it result in just one error message, IMO.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518093047.3697887-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
IPR_CHANNELNUMBERMASK cannot be non-zero when IPR_CHANNELLOOP is unset,
so join marking them as handled.
This logically reverts part of commit f453e20d8a0 ("ALSA update
0.9.3a"), which made the inverse change with no explanation.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518093047.3697887-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The period_bytes_min parameter and the buffer_bytes minimum constraint
made no sense at all, as they didn't reflect any hardware limitation.
Instead, apply a frame-based period_size minimum constraint, which is
derived from the cache size (it would be actually possible to go below
that, but it would require special handling, and it would be practically
impossible to keep up with the IRQ rate anyway).
Sync up the constraints of the EFX playback with those of the regular
playback, as there is no reason for them to diverge.
N.b., the maximum buffer size is actually arbitrary - the hardware could
go waay beyond 128 KiB.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230518092224.3696958-9-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull the special handling of extra voices out of
snd_emu10k1_pcm_init_voice(), simplify snd_emu10k1_playback_pointer(),
and make the logic overall clearer. Also, add verbose comments.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230517174256.3657060-9-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rename snd_emu10k1_playback_invalidate_cache() to the more apt
snd_emu10k1_playback_fill_cache(), and factor out
snd_emu10k1_playback_prepare_voices(), which calls the former for all
channels.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230517174256.3657060-8-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Originally, there was a 1:1 relationship between the PCM streams' and
the low-level voices' parameters. The addition of multi-channel playback
partially invalidated that, but didn't introduce proper layering, so
things kept working only by virtue of the multi-channel device never
having two channels (yet). The upcoming addition of 32-bit playback
would complete upending the relationships.
So this patch detaches the low-level parameters from the high-level
ones: we pass pre-calculated bit width and stereo flags to the low-level
manipulation functions instead of calculating them in-place from the
stream parameters.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230517174256.3657060-7-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The cache causes a fixed delay regardless of stream parameters.
Consequently, all that "cache invalidate size" calculation stuff was
garbage (which can be traced right back to Creative's OSS driver).
This also removes the definitions of registers CD1..CDF, because they
are accessed only relative to CD0 anyway.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230517174256.3657060-5-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Given that the data is going to be ignored anyway, and that the cache
does not influence interrupt timing (which is the purpose of the extra
voices), it's pointless to pre-fill the cache.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230517174256.3657060-4-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The idea is to make the extra voice lag behind the "real" voices, but
moving the buffer address around doesn't contribute to that, as the CCCA
write below uses the same address. The exact address is unimportant, as
the data is discarded anyway.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230517174256.3657060-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This workaround fails to address the underlying problem, which is
actually wholly self-made. Subsequent patches will fix it.
This reverts commit 56385a12d9.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230517174256.3657060-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Shrink the {in,out}put_source arrays and their data type to what is
actually necessary.
To be still on the safe side, add some static asserts.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230516093612.3536508-11-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unlike the other models, this is actually a distinct card, rather than
an E-MU 1010 with different "dongles". It is stereo only, and supports
no ADAT (there is no trace of ADAT in the manual, switching the output
mode to ADAT has no effect, and switching the input mode to ADAT just
breaks input (presumably ... my only ADAT source is the card's output)).
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230516093612.3536508-10-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The more card models are handled separately, the more code duplication
this saves.
add_emu1010_source_mixers() is factored out the save duplication in a
later commit.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230516093612.3536508-8-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... and move it to the mixer init, as it's logically part of it.
As a side effect, this fixes the initial values of the input destination
mixer controls, which would have previously remained at "Silent" despite
different defaults. This didn't really matter, though, as ALSA state
restoration would hide that bug beyond first use.
Note that this completely does away with clearing the output routing
registers, as it was rather pointless - we just programmed the FPGA
(resetting it first if necessary), so everything is zeroed anyway
(that's documented by Xilinx, and as further evidence, some of the loops
terminated too early, and we didn't bother clearing the high channels of
the input routes at all, all with no observed adverse effects).
As a drive-by, this also fixes some capture channel defaults - any
EMU_SRC_*2 isn't a sensible value in 1x clock mode.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230516093612.3536508-7-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of hard-coding the card-specific arrays and their sizes in each
function, use a more data-driven approach.
As a drive-by, also hide the unavailable I2S input destinations on the
1616 cardbus card.
Also as a drive-by, use more assignments at variable declaration for
brevity. This also removes the pointless masking of kctl.private_value.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230516093612.3536508-5-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Define arrays of strings instead of snd_kcontrol_new.
While at it, move the E-MU source & destination enum defs next to their
hardware defs, which is a lot more logical and will come in handy in a
followup commit. And add some static asserts to verify that the array
sizes match.
This also applies the compactization from the previous commit to the
destination registers.
While reshuffling the arrays anyway, switch the order of the HAMOA_DAC
& HANA_SPDIF output destinations for the 1010 card, so they follow a
more regular pattern. This should have no functional impact.
The code is somewhat de-duplicated by the extraction of add_ctls().
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230516093612.3536508-4-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use macros to avoid duplication. Arguably, this is somewhat less
legible, but future additions would grow this part of the file to
completely unmanageable dimensions.
The EMU*_COMMON_TEXTS macros will save duplication in a future commit;
I pulled them ahead to reduce churn.
While rewriting the tables anyway, rearrange them such that each card's
strings and registers are adjacent.
Also, add some static asserts to verify that the array sizes match.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230516093612.3536508-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Many registers are meaningless for stereo slaves and the extra voices.
This patch cleans up these unnecessary register writes.
snd_emu10k1_playback_{trigger,stop}_voice() is not called for stereo
slaves any more.
snd_emu10k1_playback_prepare_voice() is renamed to
snd_emu10k1_playback_unmute_voice(), as this better reflects its
remaining function. It's not called for the extra voices any more.
Accordingly, snd_emu10k1_playback_mute_voice() is factored out from
snd_emu10k1_playback_stop_voice(), and is called selectively as well.
This doesn't add conditionals which would avoid initializing
sub-registers, as that wouldn't pull its weight.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230516093612.3536451-6-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We now enable ints even before triggering, and disable them only after
stopping - otherwise there is a race condition we may plausibly run into
when we pause/resume near the end of the buffer.
Updating the epcm->running flag is moved the same way, as it affects the
*_pointer() functions, which are called by the interrupt handler.
Also, factor these out to own functions, for clarity.
For multi-channel, the extra voice is now triggered after all regular
voices - we wouldn't want to receive an int before all channels have
passed the period boundary.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230516093612.3536451-5-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We initialize them at card init and don't touch them later, so there is
no need to reset them again at voice start.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230516093612.3536451-4-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We (rightfully) don't enable the envelope engine for PCM voices, so any
related setup is entirely pointless - the EMU8K documentation makes that
very clear, and the fact that the various open drivers all use different
values to no observable detriment pretty much confirms it.
The remaining initializations are regrouped for clarity.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230516093612.3536451-3-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mixer structures were filled in two places: on driver init, and when
the devices are opened. The latter made the former pointless, so we
remove the former. This implies that mixer dumps may now return all
zeroes, which is OK, as restoring them is meaningless as well.
Things were even weirder for the (generally unused) secondary sends:
Some of the initialization loops were forgotten when support for Audigy
was added, thus creating the technically illegal state of multiple sends
being routed to the same FX accumulator (though it apparently doesn't
matter when the amount is zero).
The global multi-channel init used some rather bizarre values for the
secondary sends, and the init on open actually forgot to re-initialize
them. We now use a not really more useful, but simpler formula.
The direct register init was also bogus. This doesn't really matter, as
the value is overwritten when a voice comes into use, but still.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230516093612.3536451-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These IDs are for AD102, AD103, AD104, AD106, and AD107 gpus with
audio functions that are largely similar to the existing ones.
Tested audio using gnome-settings, over HDMI, DP-SST and DP-MST
connections on AD106 gpu.
Signed-off-by: Nikhil Mahale <nmahale@nvidia.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230517090736.15088-1-nmahale@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_cs46xx_download_image() was originally called from dsp_spos.c, but
is now local to cs46xx_lib.c. Mark it as 'static' to avoid a warning
about it lacking a declaration, and '__maybe_unused' to avoid a warning
about it being unused when CONFIG_SND_CS46XX_NEW_DSP is disabled:
sound/pci/cs46xx/cs46xx_lib.c:534:5: error: no previous prototype for 'snd_cs46xx_download_image'
Fixes: 89f157d9e6 ("[ALSA] cs46xx - Fix PM resume")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230516195046.550584-1-arnd@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
get_line_out_pfx() may trigger an Oops by overflowing the static array
with more than 8 channels. This was reported for MacBookPro 12,1 with
Cirrus codec.
As a workaround, extend for the 9.1 channels and also fix the
potential Oops by unifying the code paths accessing the same array
with the proper size check.
Reported-by: Olliver Schinagl <oliver@schinagl.nl>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/64d95eb0-dbdb-cff8-a8b1-988dc22b24cd@schinagl.nl
Link: https://lore.kernel.org/r/20230516184412.24078-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The voice volume is a raw fractional multiplier that can't actually
represent 1.0. To still enable real pass-through, we now set the volume
to 0.5 (which results in no loss of precision, as the FX bus provides
fractional values) and scale up the samples in DSP code.
To maintain backwards compatibility with existing configuration files,
we rescale the values in the mixer controls. The range is extended
upwards from 0xffff to 0x1fffd, which actually introduces the
possibility of specifying an amplification.
There is still a minor incompatibility with user space, namely if
someone loaded custom DSP code. They'll just get half the volume, so
this doesn't seem like a big deal.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230514170323.3408834-8-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fractional multiplication with the maximal value 2^31-1 causes some tiny
distortion. Instead, we want to multiply with the full 2^31. The catch
is of course that this cannot be represented in the DSP's signed 32 bit
registers.
One way to deal with this is to encode 1.0 as a negative number and
special-case it. As a matter of fact, the SbLive! code path already
contained such code, though the controls never actually exercised it.
A more efficient approach is to use negative values, which actually
extend to -2^31. Accordingly, for all the volume adjustments we now use
the MAC1 instruction which negates the X operand.
The range of the controls in highres mode is extended downwards, so -1
is the new zero/mute. At maximal excursion, real zero is not mute any
more, but I don't think anyone will notice this behavior change. ;-)
That also required making the min/max/values in the control structs
signed. This technically changes the user space interface, but it seems
implausible that someone would notice - the numbers were actually
treated as if they were signed anyway (and in the actual mixer iface
they _are_). And without this change, the min value didn't even make
sense in the first place (and no-one noticed, because it was always 0).
Tested-by: Jonathan Dowland <jon@dow.land>
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230514170323.3408834-7-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The microphone capture device is a feature of the AC97 codec, so its
availability should be coupled to the presence of that codec.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230514170323.3408834-6-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The E-MU cards don't try very hard to be Sound Blasters. All sound I/O
goes through the Hana FPGA, thus making the regular extin/out controls
useless. Still showing them just serves to clutter up the interface and
confuse the user.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230514170323.3408834-5-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
User space could pass arbitrary ranges, which were uncritically
accepted. This could lead to table lookups out of range.
I don't think that this is a security issue, as it only allowed someone
with CAP_SYS_ADMIN to crash the kernel, but still.
Setting an invalid translation mode will also be rejected now. That did
no harm, but it's still better to detect errors.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230514170323.3408834-4-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Pull ahead all fixed allocations, so we don't rely on the semi-
dynamic ones not crossing the arbitrarily determined limit
- Use an enum for the fixed allocations
- Stop arbitrarily wasting registers on unexplained "reservations"
- Don't reserve two regs for the master volume control - it's mono
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230514170323.3408834-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rather than applying masks to the provided values, make assertions
about them being valid - otherwise we'd just try to paper over bugs.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230514170323.3408798-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There's yet another laptop that needs the fixup to enable mute and
micmute LEDs. So do it accordingly.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230512083417.157127-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Pavilion 15 line has B&O top speakers similar to the x360 and
applying the same profile produces good sound. Without this, the
sound would be tinny and underpowered without either applying
model=alc295-hp-x360 or booting another OS first.
Signed-off-by: Ryan Underwood <nemesis@icequake.net>
Fixes: 563785edfc ("ALSA: hda/realtek - Add quirk entry for HP Pavilion 15")
Link: https://lore.kernel.org/r/ZF0mpcMz3ezP9KQw@icequake.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of using lots of instructions to mix wet and dry signals,
simply skip over the whole code block if tone control is disabled.
This also allows us doing away with the "shadow" playback channels.
Tested-by: Jonathan Dowland <jon@dow.land>
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230510173917.3073107-7-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Evidently, the channel delay bug exists in all E-MU cards; it's in the
Hana FPGA program, and was never fixed.
Note that the implementation is somewhat lazy - to localize the code
paths, we actually waste a GPR and a DSP instruction by keeping two
delay registers for the same physical source.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230510173917.3073107-6-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of spending lots of instructions on masking and transplanting
the sign bit, sidestep the issue by replacing the last bit shift with
a wrapping addition to self.
Solution stolen from kX-project, after I pondered other ideas first.
Also, the function really doesn't need to return a constant int value.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230510173917.3073107-5-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Presumably, JDC added the seemingly superfluous indirection over the
temporary register because without it he'd get only zero readings.
However, switching the X and Y operands (or using EMU32 as the A
operand in the temporary load) works just fine. Presumably a DSP bug?
The original code was also actually buggy, though: both channels used
the left volume control.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230510173917.3073107-4-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It controls the whole surround set, so stereo can't work. As a
consequence, only the left channel was paid attention to.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230510173917.3073107-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These models use 2 CS35L41 amplifiers using SPI for down-facing
speakers.
alc285_fixup_speaker2_to_dac1 is needed to fix volume control of the
down-facing speakers.
Pin configs are needed to enable headset mic detection.
Note that these models lack the ACPI _DSD properties needed to
initialize the amplifiers. They can be added during boot to get working
sound out of the speakers:
https://gist.github.com/lamperez/862763881c0e1c812392b5574727f6ff
Signed-off-by: Alexandru Sorodoc <ealex95@gmail.com>
Link: https://lore.kernel.org/r/20230511161510.315170-1-ealex95@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for HP EliteBook 835/845/845W/865 G10 laptops
with CS35L41 amplifiers on I2C/SPI bus connected to Realtek codec.
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230510142227.32945-1-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Fix mixer source port names. These will require some users to
re-adjust their mixer settings, which seems acceptable:
- The S/PDIF port is on the main 1010 card, not the 0202 daughter card
- The 1616m CardBus card has all inputs on the dock, so there is
no point in specifying it
- Conversely, the 1010 card has "dispersed" inputs, so say where the
ADAT port is, consistently with the S/PDIF port
- The 1616m CardBus card is actually named E-MU 02 (due to the headphone
output jack it has)
- Fix capitalization of "E-MU"
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230428095941.1706335-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
