The Wacom W8001 sensor is a sensor device (uses electromagnetic
resonance) and it is interfaced via its serial microcontroller
to the host.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
According to Section 2.4.4 of the Synaptics TouchPad Interfacing
Guide, bit 2 specifies if multi-finger detection is provided by
the touchpad. Thus, only set BTN_TOOL_DOUBLETAP and
BTN_TOOL_TRIPLETAP if the device actually supports it.
Signed-off-by: Peter Hutterer <peter.hutterer@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The usbtouchscreen module implements a driver for the TSC-10 DM USB
touchscreen controllers, but assumes a 2-byte response for the
CMD_RESET and CMD_RATE commands, when they can be only a single byte
when no EEPROM is connected.
The driver worked with an earlier controller revision, but new
revisions of the controller fail.
It seems the problem is that the early controller had the
SEL4/EEPROM-CS pin high, but the new controller has it down, making
the response different.
Without the fix, the controller would answer the single byte 0x06
(ACK), making the init fail with -ENODEV because buf[1] is 0xFF (as
initialized before).
As the single byte is the only thing we need to check it was ok, there
is no need to verify the second byte.
The [0x15 0x01] case is the NAK [0x15] response for when there is no
data in the EEPROM [bit-0 of second byte set], so I let that be, as I
don't have any controller with an EEPROM.
With this patch, both the earlier and latest controller work the same.
Note: This was previously submited as BUG #11961 [1] on the bugzilla
tracker, but rebased to version 2.6.27.4 and with unnecessary comments
and printk's removed.
[1] http://bugzilla.kernel.org/show_bug.cgi?id=11961
Signed-off-by: Nuno Lucas <ntlucas@gmail.com>
Acked-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is no reason to limit the GPIO rows to 6 for OMAP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The GPIO interrupts are disabled several times after the first key press.
No need to disable - again - the interrupts in the omap_kp_scan_keypad
function on OMAP2.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The appletouch driver has grown up from supporting only a couple of
touchpads into supporting many touchpads, which can have different
number of sensors, different aspect ratios etc.
This patch cleans up the current driver code and makes it easy to
support the features of each different touchpad.
As a side effect, this patch also modifies the 'Y' multiplication factor
of the 'geyser3' and 'geyser4' touchpads (found on Core Duo and Core2
Duo MacBook and MacBook Pro laptops) in order to make the touchpad
output match the aspect ratio of the touchpad (Y factor changed from 43
to 64).
[dtor@mail.ru: make atp_info constant]
Signed-off-by: Stelian Pop <stelian@popies.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds a flag to gpio-key driver to turn on the input subsystems
auto repeat feature if needed.
Signed-off-by: Dominic Curran <dcurran@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Review comments were incorporated to improve the driver.
1. Some data was eliminated that was not needed.
2. Renaming of variables for clarity.
3. Removed unneeded type casting.
4. Changed to use dev_err rather than other I/O.
5. Merged together some functions.
6. Added kerneldoc format to functions.
Signed-off-by: Sadanand <sadanan@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Currently, evdev has working 32bit compatibility and uinput does not. uinput
needs the input_event code that evdev uses, so let's refactor it so it can
be shared.
[dtor@mail.ru: add fix for force feedback compat issues]
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
libata: fix NCQ devices behind port multipliers
scsi: make sure that scsi_init_shared_tag_map() doesn't overwrite existing map
For devices behind sata port multipliers, we have to make sure that
they share a tag map since all tags for that PMP must be unique.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Right now callers have to check whether scsi_host->bqt is already
set up, it's much cleaner to just have scsi_init_shared_tag_map()
does this check on its own.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ASoC: Blackfin: update SPORT0 port selector (v2)
ALSA: hda - Restore default pin configs for realtek codecs
sound: use a common working email address
pci: use pci_ioremap_bar() in sound/
When booting Linux on a txx9 board with VxWorks boot loader, it crashes in
prom_getenv(), as VxWorks doesn't pass firmware parameters in a0-a3 (in my
case, the actual leftover values in these registers were 0x80002000,
0x80001fe0, 0x2000, and 0x20).
Make the parsing of argc, argv, and envp a bit more robust by checking if
argc is a number below CKSEG0, and argv/envp point to CKSEG0.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove runtime db_* macros as we don't need them any more. In general,
such helpers are useful for initial porting, but once approved, they are
not indispensable.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Current EMMA2RH irq code is mess. Before cleaning it up, gather them
in one place as a first step.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Let's use immediate value, instead. This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Let's use immediate value, instead. This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Let's use immediate value, instead. This also saves memory footprint,
and probably a little bit faster.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We'll put all EMMA related headers there in the future.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
git mv arch/mips/{emma2rh,emma} and fixups Makefiles. We'll put all NEC
EMMA series based machines there in the future.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Move EMMA related stuff into arch/mips/emma/Kconfig
- Create CONFIG_SOC_EMMA* to handle more EMMA SoCs effectively
- Rename CONFIG_MARKEINS into CONFIG_NEC_MARKEINS
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We already have sufficient infrastructure to support VR5500 and VR5500A
series processors. Here's a Makefile support to make it selectable by
ports, and enable it for NEC EMMA2RH Markeins board.
This patch also fixes a confused target help, and adds 1Gb PageMask bits
supported by VR5500 and its variants.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The following patch add support for the NXP PNX833x SOC. More
specifically it adds support for the STB222/5 variant. It fixes
the vectored interrupt issue.
Signed-off-by: daniel.j.laird <daniel.j.laird@nxp.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix a typo in the comment for the TOSHIBA_RBTX4939 config option
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In file included from include/linux/ptrace.h:49,
from arch/mips/kernel/kgdb.c:25:
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:123: error: expected declaration specifiers or '...' before '__s64'
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:124: error: expected declaration specifiers or '...' before '__s64'
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:126: error: expected declaration specifiers or '...' before '__u32'
/home/yuasa/src/linux/test/mips/linux/arch/mips/include/asm/ptrace.h:127: error: expected declaration specifiers or '...' before '__u32'
make[1]: *** [arch/mips/kernel/kgdb.o] Error 1
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The SGI Volume Button interface driver uses GPL-only symbols
platform_driver_unregister and platform_driver_register, but
lacks license specification. Thus, when compiled as a module,
this driver cannot be installed. This patch fixes this by
adding the MODULE_LICENSE() specification.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The following functions
disable_local1_irq()
disable_local2_irq()
disable_local3_irq()
are needlessly defined global, so make them static. While at it, fix a
whitespace error in the same file.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add smc91x platform device to RBTX4939 board and some hacks for big endian.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add au1xmmc platform data for PB1200/DB1200 boards and wire up the 2 SD
controllers for them.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch sets the correct interrupt status and level
in order to get the CompactFlash adapter working.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
mips/pci/fixup-rc32434.c must #include <asm/mach-rc32434/irq.h>
This patch fixes the following compile error caused by
commit 606a083b1e
(MIPS: RB532: Cleanup the headers again):
<-- snip -->
...
CC arch/mips/pci/fixup-rc32434.o
arch/mips/pci/fixup-rc32434.c: In function 'pcibios_map_irq':
arch/mips/pci/fixup-rc32434.c:46: error: 'GROUP4_IRQ_BASE' undeclared (first use in this function)
arch/mips/pci/fixup-rc32434.c:46: error: (Each undeclared identifier is reported only once
arch/mips/pci/fixup-rc32434.c:46: error: for each function it appears in.)
make[2]: *** [arch/mips/pci/fixup-rc32434.o] Error 1
<-- snip -->
A virtually identical patch was also submitted by Yoichi Yuasa
<yoichi_yuasa@tripeaks.co.jp>.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
<asm/ptrace.h> is exported to userland so can't include <linux/ptrace.h>,
so replace the C99 types with their basic C type equivalents.
Bug originally reported and initial patch by Yoichi Yuasa
<yoichi_yuasa@tripeaks.co.jp>.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We were getting away with this for so long only because the only platform
with a non-empty plat_unmap_dma_mem() doesn't call dma_sync_sg_for_cpu()
and dma_sync_sg_for_device() from its commonly used drivers.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
debugfs_create_*() returns NULL on error. Make its callers return -ENODEV
on error.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
