This reverts commit 35773dac5f. It's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb. Commit 70cabb7d992f "xhci 1.0: Limit
arbitrarily-aligned scatter gather." should fix the issues seen with the
ax88179_178a driver on xHCI 1.0 hosts, without causing regressions.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org # 3.12
This reverts commit d6c9ea9069.
We are ripping out commit 35773dac5f "usb:
xhci: Link TRB must not occur within a USB payload burst" because it's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb. This commit attempted to fix the
issues with that patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org # 3.12
This reverts commit f2d9b991c5.
We are ripping out commit 35773dac5f "usb:
xhci: Link TRB must not occur within a USB payload burst" because it's a
hack that caused regressions in the usb-storage and userspace USB
drivers that use usbfs and libusb. This commit attempted to fix the
issues with that patch.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org #3.12
xHCI 1.0 hosts have a set of requirements on how to align transfer
buffers on the endpoint rings called "TD fragment" rules. When the
ax88179_178a driver added support for scatter gather in 3.12, with
commit 804fad45411b48233b48003e33a78f290d227c8 "USBNET: ax88179_178a:
enable tso if usb host supports sg dma", it broke the device under xHCI
1.0 hosts. Under certain network loads, the device would see an
unexpected short packet from the host, which would cause the device to
stop sending ethernet packets, even through USB packets would still be
sent.
Commit 35773dac5f "usb: xhci: Link TRB must not occur within a USB
payload burst" attempted to fix this. It was a quick hack to partially
implement the TD fragment rules. However, it caused regressions in the
usb-storage layer and userspace USB drivers using libusb. The patches
to attempt to fix this are too far reaching into the USB core, and we
really need to implement the TD fragment rules correctly in the xHCI
driver, instead of continuing to wallpaper over the issues.
Disable arbitrarily-aligned scatter-gather in the xHCI driver for 1.0
hosts. Only the ax88179_178a driver checks the no_sg_constraint flag,
so don't set it for 1.0 hosts. This should not impact usb-storage or
usbfs behavior, since they pass down max packet sized aligned sg-list
entries (512 for USB 2.0 and 1024 for USB 3.0).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Mark Lord <mlord@pobox.com>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Freddy Xin <freddy@asix.com.tw>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: stable@vger.kernel.org # 3.12
Hi Greg,
Here's four patches for 3.14.
One of them adds an xHCI host quirk, and the other three of them fix
regressions introduced in 3.14. One regression causes USB 3.0 Link PM to
be enabled on all xHCI hosts (even those that may not support it), which
causes some USB 3.0 devices to not enumerate. A second regression causes
some xHCI hosts that don't support 64-bit addressing to stop responding to
commands and die.
Note, these patches don't fix the recent usbfs regression that was caused
by commit 35773dac5f "usb: xhci: Link TRB
must not occur within a USB payload burst". I'm waiting for those patches
to be tested.
Please pull usb-linus into usb-next, as I have feature patches that rely on
140e3026a5 Revert "usbcore: set lpm_capable field for LPM capable root
hubs"
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=sPwW
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2014-02-04' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
Sarah writes:
xhci: Fix some regressions introduced in 3.14.
Hi Greg,
Here's four patches for 3.14.
One of them adds an xHCI host quirk, and the other three of them fix
regressions introduced in 3.14. One regression causes USB 3.0 Link PM to
be enabled on all xHCI hosts (even those that may not support it), which
causes some USB 3.0 devices to not enumerate. A second regression causes
some xHCI hosts that don't support 64-bit addressing to stop responding to
commands and die.
Note, these patches don't fix the recent usbfs regression that was caused
by commit 35773dac5f "usb: xhci: Link TRB
must not occur within a USB payload burst". I'm waiting for those patches
to be tested.
Please pull usb-linus into usb-next, as I have feature patches that rely on
140e3026a5 Revert "usbcore: set lpm_capable field for LPM capable root
hubs"
Sarah Sharp
This reverts commit e8b373326d. Many xHCI
host controllers can only handle 32-bit addresses, and writing 64-bits
at a time causes them to fail. Reading 64-bits at a time may also cause
them to return 0xffffffff, so revert this commit as well.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This reverts commit 7dd09a1af2.
Many xHCI host controllers can only handle 32-bit addresses, and writing
64-bits at a time causes them to fail. Rafał reports that USB devices
simply do not enumerate, and reverting this patch helps. Branimir
reports that his host controller doesn't respond to an Enable Slot
command and dies:
[ 75.576160] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 88.991634] xhci_hcd 0000:03:00.0: Stopped the command ring failed, maybe the host is dead
[ 88.991748] xhci_hcd 0000:03:00.0: Abort command ring failed
[ 88.991845] xhci_hcd 0000:03:00.0: HC died; cleaning up
[ 93.985489] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 93.985494] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead.
[ 98.982586] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 98.982591] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead.
[ 103.979696] xhci_hcd 0000:03:00.0: Timeout while waiting for a slot
[ 103.979702] xhci_hcd 0000:03:00.0: Abort the command ring, but the xHCI is dead
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Reported-by: Branimir Maksimovic <branimir.maksimovic@gmail.com>
Cc: Xenia Ragiadakou <burzalodowa@gmail.com>
<<
Switch mpc512x to the common clock framework and adapt mpc512x
drivers to use the new clock driver. Old PPC_CLOCK code is
removed entirely since there are no users any more.
>>
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree.
The largest part of this is a conversion of device registration for some
renesas shmobile/sh devices over to use resources. This has required
coordination with the corresponding arch/sh changes, and we've agreed
to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure firmware,
which is what is used on many of the commercial Nvidia Tegra products
that are in the market, including the Nvidia Shield. The code is local
to arch/arm at this time since it's uncertain whether it will be shared
with arm64 longer-term, if needed we will refactor later.
A couple of new RTC drivers used on ARM boards, merged through our tree
on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JJlw
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
Don Zickus <dzickus@redhat.com> writes:
Some co-workers of mine bought Samsung laptops that had mostly usb3 ports.
Those ports did not resume correctly (the driver would timeout communicating
and fail). This led to frustration as suspend/resume is a common use for
laptops.
Poking around, I applied the reset on resume quirk to this chipset and the
resume started working. Reloading the xhci_hcd module had been the temporary
workaround.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Don Zickus <dzickus@redhat.com>
Tested-by: Prarit Bhargava <prarit@redhat.com>
Cc: stable # 2.6.37
According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement a special ehci_write
for imx28.
Discussion for it at below:
http://marc.info/?l=linux-usb&m=137996395529294&w=2
Without this patcheset, imx28 works unstable at high AHB bus loading.
If the bus loading is not high, the imx28 usb can work well at the most
of time. There is a IC errata for this problem, usually, we consider
IC errata is a problem not a new feature, and this workaround is needed
for that, so we need to add them to stable tree 3.11+.
Cc: stable@vger.kernel.org
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
after device tree based clock lookup became available, the peripheral
driver need no longer construct clock names which include the component
index -- remove the "usb%d_clk" template, always use "ipg" instead
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 35773dac5f "usb: xhci: Link TRB
must not occur within a USB payload burst" attempted to fix an issue
found with USB ethernet adapters, and inadvertently broke USB storage
devices. The patch attempts to ensure that transfers never span a
segment, and rejects transfers that have more than 63 entries (or
possibly less, if some entries cross 64KB boundaries).
usb-storage limits the maximum transfer size to 120K, and we had assumed
the block layer would pass a scatter-gather list of 4K entries,
resulting in no more than 31 sglist entries:
http://marc.info/?l=linux-usb&m=138498190419312&w=2
That assumption was wrong, since we've seen the driver reject a write
that was 218 sectors long (of probably 512 bytes each):
Jan 1 07:04:49 jidanni5 kernel: [ 559.624704] xhci_hcd 0000:00:14.0: Too many fragments 79, max 63
...
Jan 1 07:04:58 jidanni5 kernel: [ 568.622583] Write(10): 2a 00 00 06 85 0e 00 00 da 00
Limit the number of scatter-gather entries to half a ring segment. That
should be margin enough in case some entries cross 64KB boundaries.
Increase the number of TRBs per segment from 64 to 256, which should
result in ring segments fitting on a 4K page.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: jidanni@jidanni.org
References: http://bugs.debian.org/733907
Fixes: 35773dac5f ('usb: xhci: Link TRB must not occur within a USB payload burst')
Cc: stable <stable@vger.kernel.org> # 3.12
Currently prepare_ring() returns -ENOMEM if the urb won't fit into a
single ring segment. usb_sg_wait() treats this error as a temporary
condition and will keep retrying until something else goes wrong.
The number of retries should be limited in usb_sg_wait(), but also
prepare_ring() should not return an error code that suggests it might
be worth retrying. Change it to -EINVAL.
Reported-by: jidanni@jidanni.org
References: http://bugs.debian.org/733907
Fixes: 35773dac5f ('usb: xhci: Link TRB must not occur within a USB payload burst')
Cc: stable <stable@vger.kernel.org> # 3.12
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
After commit 99f14bd4d1 "Merge 3.13-rc5 into usb-next" (in linux-next as of
today), I'm getting this error building any at91 kernel:
drivers/usb/host/ohci-at91.c: In function 'usb_hcd_at91_probe':
drivers/usb/host/ohci-at91.c:190:4: error: label 'err' used but not defined
goto err;
^
drivers/usb/host/ohci-at91.c: At top level:
drivers/usb/host/ohci-at91.c:206:2: warning: data definition has no type or storage class [enabled by default]
at91_stop_hc(pdev);
^
...
The problem is obviously a mismerge between two unrelated changes that
resulted in missing opening braces.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---------------------------
This pull request contains updates
to DaVinci GPIO driver and the
resultant platform code changes. The
updates include DT-conversion and
changes to make the driver cross-platform
ready.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=DxLt
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
From Sekhar Nori:
DaVinci GPIO driver updates
---------------------------
This pull request contains updates to DaVinci GPIO driver and the
resultant platform code changes. The updates include DT-conversion and
changes to make the driver cross-platform ready.
* tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
Signed-off-by: Olof Johansson <olof@lixom.net>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Happy Holidays, Greg!
Here's four patches to be queued to usb-next for 3.14.
One adds a module parameter to the xHCI driver to allow users to enable
xHCI quirks without recompiling their kernel, which you've already said
is fine. The second patch is a bug fix for new usbtest code that's only
in usb-next. The third patch is simple cleanup.
The last patch is a non-urgent bug fix for xHCI platform devices. The
bug has been in the code since 3.9. You've been asking me to hold off
on non-urgent bug fixes after -rc4/-rc5, so it can go into usb-next, and
be backported to stable once 3.14 is out.
These have all been tested over the past week. I did run across one
oops, but it turned out to be a bug in 3.12, and therefore not related
to any of these patches.
Please queue these for usb-next and 3.14.
Thanks,
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=PRbx
-----END PGP SIGNATURE-----
Merge tag 'for-usb-next-2013-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-next
Sarah writes:
xhci: Cleanups, non-urgent fixes for 3.14.
Happy Holidays, Greg!
Here's four patches to be queued to usb-next for 3.14.
One adds a module parameter to the xHCI driver to allow users to enable
xHCI quirks without recompiling their kernel, which you've already said
is fine. The second patch is a bug fix for new usbtest code that's only
in usb-next. The third patch is simple cleanup.
The last patch is a non-urgent bug fix for xHCI platform devices. The
bug has been in the code since 3.9. You've been asking me to hold off
on non-urgent bug fixes after -rc4/-rc5, so it can go into usb-next, and
be backported to stable once 3.14 is out.
These have all been tested over the past week. I did run across one
oops, but it turned out to be a bug in 3.12, and therefore not related
to any of these patches.
Please queue these for usb-next and 3.14.
Thanks,
Sarah Sharp
If CONFIG_PCI is enabled, make sure xhci_cleanup_msix()
doesn't try to free a bogus PCI IRQ or dereference an invalid
pci_dev when the xHCI device is actually a platform_device.
This patch should be backported to kernels as old as 3.9, that
contain the commit 52fb61250a
"xhci-plat: Don't enable legacy PCI interrupts."
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
Use devm_ioremap_resource() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_ioremap_resource() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_ioremap_resource() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_clk_get() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_ioremap_resource() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_ioremap_resource() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_ioremap_resource() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_warn() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_warn() instead of printk() to provide a better message
to userspace.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make use of the dev variable instead of referencing the dev field of the
pdev struct.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the request_mem_region + ioremap calls by the
devm_ioremap_resource call which does the same things but with device
managed resources.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch remove unused variable 'addr' in inc_deq() and inc_enq().
Signed-off-by: Lin Wang <lin.x.wang@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
When using dt resources retrieval (interrupts and reg properties) there is
no predefined order for these resources in the platform dev resources
table.
Retrieve resources using platform_get_resource and platform_get_irq
functions instead of direct resource table entries to avoid resource type
mismatch.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It makes easier for debugging some hardware specific issues.
Note that this option won't override the value to be set. That is,
you can turn quirks on by this option but cannot turn them off if set
by the driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Specify whether we are only performing the context setup portion of the
'address device' command, or the full operation issuing 'SetAddress'
on the wire.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Change the default enumeration scheme for xhci attached non-SuperSpeed
devices from:
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(8)
GetDescriptor(18)
...to:
Reset
[xhci address-device BSR = 1]
GetDescriptor(64)
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(18)
...as some devices misbehave when encountering a SetAddress command
prior to GetDescriptor. There are known legacy devices that require
this scheme, but testing has found at least one USB3 device that fails
enumeration when presented with this ordering. For now, follow the ehci
case and enable 'new scheme' by default for non-SuperSpeed devices.
To support this enumeration scheme on xhci the AddressDevice operation
needs to be performed twice. The first instance of the command enables
the HC's device and slot context info for the device, but omits sending
the device a SetAddress command (BSR == block set address request).
Then, after GetDescriptor completes, follow up with the full
AddressDevice+SetAddress operation.
As mentioned before, this ordering of events with USB3 devices causes an
extra state transition to be exposed to xhci. Previously USB3 devices
would transition directly from 'enabled' to 'addressed' and never need
to underrun responses to 'get descriptor'. We do see the 64-byte
descriptor fetch the correct data, but the following 18-byte descriptor
read after the reset gets:
bLength = 0
bDescriptorType = 0
bcdUSB = 0
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
instead of:
bLength = 12
bDescriptorType = 1
bcdUSB = 300
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
which results in the discovery process looping until falling back to
'old scheme' enumeration.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Moore <david.moore@gmail.com>
Suggested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
