Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
The TI crossbar irqchip doesn't provides any facility to configure the
wakeup sources, but the conversion to hierarchical irqdomains set the
irq_set_wake callback to irq_chip_set_wake_parent. The parent chip
(OMAP wakeupgen) has no irq_set_wake function either so the call will
fail with -ENOSYS. As a result the irq_set_wake() call in the resume
path will trigger an 'Unbalanced wake disable' warning.
Before the conversion the GIC irqchip was the top level irqchip and
correctly flagged with IRQCHIP_SKIP_SET_WAKE.
Restore the correct behaviour by removing the irq_set_type callback
from the crossbar irqchip and set the IRQCHIP_SKIP_SET_WAKE flag which
lets the irq_set_irq_wake() call from the driver succeed.
[ tglx: Massaged changelog ]
Fixes: 783d31863f ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-7-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The ARM GIC requires that all interrupts which are not used as a
wakeup source have to be masked during suspend.
The conversion of the crossbar irqchip to hierarchical irq domains
failed to mark the crossbar irqchip with the IRQCHIP_MASK_ON_SUSPEND
flag and therefor broke the suspend requirement of the GIC.
Before the conversion the flags were visible because the GIC was the
top level irqchip. After the conversion the crossbar irqchip is the
top level irq chip whose flags are evaluated in suspend_device_irq().
As the flag is not set the masking of the non-wakeup irqs is not
invoked which breaks suspend.
Add the IRQCHIP_MASK_ON_SUSPEND flag to the crossbar irqchip, so the
GIC interrupts get masked properly.
[ tglx: Massaged changelog ]
Fixes: 783d31863f ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-6-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The conversion of the crossbar irqchip to hierarchical irq domains
failed to provide a mechanism to properly set the trigger type of an
interrupt.
The crossbar irq chip itself has no mechanism and therefor no
irq_set_type() callback. The code before the conversion relayed the
trigger configuration directly to the underlying GIC.
Restore the correct behaviour by setting the crossbar irq_set_type
callback to irq_chip_set_type_parent(). This propagates the
set_trigger() call to the underlying GIC irqchip.
[ tglx: Massaged changelog ]
Fixes: 783d31863f ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-4-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Support for the TI crossbar used on the DRA7 family of chips
is implemented as an ugly hack on the side of the GIC.
Converting it to stacked domains makes it slightly more
palatable, as it results in a cleanup.
Unfortunately, as the DT bindings failed to acknowledge the
fact that this is actually yet another interrupt controller
(the third, actually), we have yet another breakage. Oh well.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/1426088629-15377-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
My static checker complains that the ">" should be ">=" or else we go
beyond the end of the cb->irq_map[] array on the next line.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
On certain platforms such as DRA7, SPIs 0, 1, 2, 3, 5, 6, 10, 131,
132, 133 are direct wired to hardware blocks bypassing crossbar.
This quirky implementation is *NOT* supposed to be the expectation
of crossbar hardware usage. However, these are already marked in our
description of the hardware with SKIP and RESERVED where appropriate.
Unfortunately, we need to be able to refer to these hardwired IRQs.
So, to request these, crossbar driver can use the existing information
from it's table that these SKIP/RESERVED maps are direct wired sources
and generic allocation/programming of crossbar should be avoided.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-17-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This is a basic check to ensure that crossbar register needs to be
written. This ensures that we have a common check which is used in
both map and unmap logic.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-15-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Currently we attempt to map any crossbar value to an IRQ, however,
this is not correct from hardware perspective. There is a max crossbar
event number upto which hardware supports. So describe the same in
device tree using 'ti,max-crossbar-sources' property and use it to
validate requests.
[ jac - remove MAX_SOURCES from binding doc, use integer because we
shouldn't put implementation details in the binding docs ]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-14-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Using err1,2,3,4 etc makes it hard to ensure a new exit path in the
middle will not result in spurious changes, so rename the error paths
as per the function it does.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-11-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
crossbar_of_init always returns -ENOMEM in case of errors.
There can be other causes of failure like invalid data from
DT. So return a appropriate error value for that case.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-10-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Adding missing properties for kerneldoc (@write) and cleanup
of harmless warnings while we are here.
kerneldoc warnings:
Warning(drivers/irqchip/irq-crossbar.c:27): missing initial short description on line:
* struct crossbar_device: crossbar device description
Info(drivers/irqchip/irq-crossbar.c:27): Scanning doc for struct
Warning(drivers/irqchip/irq-crossbar.c:39): No description found for parameter 'write'
2 warnings
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-9-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
There is absolutely no need for crossbar driver to expose functions and
variables into global namespace. So make them all static
Also fix a couple of checkpatch warnings.
Fixes sparse warnings:
drivers/irqchip/irq-crossbar.c:129:29: warning: symbol 'routable_irq_domain_ops' was not declared. Should it be static?
drivers/irqchip/irq-crossbar.c:261:12: warning: symbol 'irqcrossbar_init' was not declared. Should it be static?
Checkpatch warnings:
WARNING: Prefer kcalloc over kzalloc with multiply
+ cb->irq_map = kzalloc(max * sizeof(int), GFP_KERNEL);
WARNING: Prefer kcalloc over kzalloc with multiply
+ cb->register_offsets = kzalloc(max * sizeof(int), GFP_KERNEL);
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-8-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
IS_ERR_VALUE makes sense only *if* there could be valid values in
negative error range. But in the cases that we do use it, there is no
such case. Just remove the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-7-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Reverse the search algorithm to ensure that address mapping and IRQ
allocation logics are proper. This makes the below bugs visible sooner.
class 1. address space errors -> example:
reg = <a size_b>
ti,max-irqs = is a wrong parameter
class 2: irq-reserved list - which decides which entries in the
address space is not actually wired in
class 3: wrong list of routable-irqs.
In general allocating from max to min tends to have benefits in
ensuring the different issues that may be present in dts is easily
caught at definition time, rather than at a later point in time.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-6-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Since crossbar is s/w configurable, the initial settings of the
crossbar cannot be assumed to be sane. This implies that:
a) On initialization all un-reserved crossbars must be initialized to
a known 'safe' value.
b) When unmapping the interrupt, the safe value must be written to
ensure that the crossbar mapping matches with interrupt controller
usage.
So provide a safe value in the dt data to map if
'0' is not safe for the platform and use it during init and unmap
While at this, fix the below checkpatch warning.
Fixes checkpatch warning:
WARNING: Unnecessary space before function pointer arguments
#37: FILE: drivers/irqchip/irq-crossbar.c:37:
+ void (*write) (int, int);
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-5-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
When, in the system due to varied reasons, interrupts might be unusable
due to hardware behavior, but register maps do exist, then those interrupts
should be skipped while mapping irq to crossbars.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-4-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
If irq_of_parse_and_map is executed twice, the same crossbar is mapped to two
different GIC interrupts. This is completely undesirable. Instead, check
if the requested crossbar event is pre-allocated and provide that GIC
mapping back to caller if already allocated.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-3-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Today '0' is actually reserved, but may not be the same in the future.
So, use a flag to mark the GIC interrupts that are reserved.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-2-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
We are allocating the size of a pointer and not the size of the data.
This will lead to memory corruption.
There isn't actually a "cb_device" struct, btw. The code is only able
to compile because GCC knows that all pointers are the same size.
Fixes: 96ca848ef7 ('DRIVERS: IRQCHIP: CROSSBAR: Add support for Crossbar IP')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sricharan R <r.sricharan@ti.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Link: http://lkml.kernel.org/r/20140403072134.GA14286@mwanda
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some socs have a large number of interrupts requests to service
the needs of its many peripherals and subsystems. All of the
interrupt lines from the subsystems are not needed at the same
time, so they have to be muxed to the irq-controller appropriately.
In such places a interrupt controllers are preceded by an CROSSBAR
that provides flexibility in muxing the device requests to the controller
inputs.
This driver takes care a allocating a free irq and then configuring the
crossbar IP as a part of the mpu's irqchip callbacks. crossbar_init should
be called right before the irqchip_init, so that it is setup to handle the
irqchip callbacks.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Kumar Gala <galak@codeaurora.org> (for DT binding portion)
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
