This message is frequently displayed even if normal file-transfer.
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The mv643xx_eth driver can be loaded as a platform device, as is done by
various Orion (ARM) based devices. The driver needs to define a module
alias for the platform driver so udev will load it automatically.
Tested with Debian on a QNAP TS-209.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When the chip dies (probably because of a bug somewhere in the driver),
de_stop_rxtx() fails and changing the media type crashes the whole machine.
Replace BUG_ON() in de_set_media() with a warning.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes the module init message to tell that the legacy
driver loaded. This makes it less confusing, in case both drivers are loaded.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace broken code that attempted to copy 6 byte array to 64-bit
integer. Due to missing cast to 64-bit integer, left shift operation
were 32-bit and lead to bytes been copied over each other. New code
uses simple memcpy, for greater readability and efficiency.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Slightly more useful if we compare it against the sequence number of the
command we have outstanding, rather than comparing the reply with itself.
Doh. Pointed out by Sebastian Siewior
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I called p54_parse_eeprom() on a hand-coded structure
I managed to make a small mistake with wrap->len which caused
a segfault a few lines down when trying to read entry->len.
This patch changes the validation code to avoid such problems.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the EEPROM structure is read from hardware, it is
always little endian, annotate that in the struct and
make sure to convert where applicable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Wu <flamingice@sourmilk.net>
Tested-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch has added pcibios_enable_device() return value check.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Every skb removed from session->reorder_q needs sock_put().
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every skb removed from session->reorder_q needs sock_put().
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Acked-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current tun/tap driver sets also net device's hw address when asked to
change character device's hw address. This is a good idea, but it
misses RTLN-locking, resulting following error message in 2.6.25-rc3's
inetdev_event() function:
RTNL: assertion failed at net/ipv4/devinet.c (1050)
Attached patch fixes this problem.
Signed-off-by: Kim B. Heino <Kim.Heino@bluegiga.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several endianity corrections in start_xmit()
Fixed TSO bug where packets were missing the TCP flags.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit traffic through an internal queue to prevent overflow.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed locking between fastpath and slowpath operations.
Corrected order of traffic disabling to prevent race when going down
under traffic.
- first have the microcode drop all incoming packets
- then do the slowpath stuff
- only then reset the MAC
Got rid of in_reset_task.
Remove_one() and friends would deference a null pointer if init_one
failed.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the HW attentions, used to indicate an error were not properly
acked.
This will cause the driver to endlessly receive interrupts when such
an error happens.
Had to break the code into smaller chunks because it got too nested.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errata A0.158 workaround.
Running in INT#A mode after running with MSI-X fails due to a PCI core
bug.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errors were summed improperly, some stats were missing.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configuration of RX filtering needed the following corrections:
Drop flags need to be set per Rx queue.
Have to tell the microcode to collect drop stats, and properly wait
for them to complete when going down.
Sometimes we failed to detect proper completion due to a logical error
in the wait loop.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly protect PHY access between two devices on the same board with
a HW lock.
Use GPIO to clear all previous configurations before changing link
parameters.
Shut down the external PHY in case of fan failure.
Reducing the MDC/MDIO clock to 2.5MHz due to problems with some
devices.
Resolve the flow control response according to autoneg with external
PHY.
Unmasking all PHY interrupts in single write to prevent a race in the
interrupts order.
LASI indication fixes to work with peculiarities of PHYs.
Disable MAC RX to avoid a HW bug when closing the MAC under traffic.
Disable parallel detection on HiGig due to HW limitation.
Updating the shared memory structure to work with the current
bootcode.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct PCI-E info printed by init_one()
In one case it failed to free the netdev.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the SSB PCI core driver to the new SPROM data structure now that
the old one has been removed.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This may happen e.g. when the ssb is statically enables by the b44 driver,
and the b43 pci-ssb bridge is enbled by the b43/b43legacy drivers, or the
b43/b43legacy drivers are built statically.
Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bridge code was unnecessary enabled by the b44
driver, but it prevents the bcm43xx driver from
being loaded, as the bridge claims the same pci ids.
Now we enable the birdge only if the b43{legacy}
drivers are selected.
Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The libertas driver exports a number of symbols with no in-tree users;
remove these unused exports. lbs_reset_device() is completely unused, with
no callers at all, so remove the function completely.
A couple of these unused exported symbols are static, which causes the
following build error on ia64 with gcc 4.2.3:
drivers/net/wireless/libertas/main.c:1375: error: __ksymtab_lbs_remove_mesh causes a section type conflict
drivers/net/wireless/libertas/main.c:1354: error: __ksymtab_lbs_add_mesh causes a section type conflict
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00lib_reset_link_tuner() can be called from within
the link tuner itself. This means that it should
_not_ call rt2x00lib_stop_link_tuner() since that will
cause the thread to hang.
Reorder the things that should be done during a
link tuner reset and during a link tuner start.
Also make antenna tuning the last step of the link
tuner since it could possibly reset some statistical
information which we need for average calculation.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rssi_a > rssi_b is true and the current antenna
was already antenna A, then rt2x00 incorrectly jumped
to antenna B.
Also don't configure the antenna when there has been
no change in the antenna setup.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds 2 new states which both are used to toggle
the RX. These new states are required for usage
inside the link tuner thread, because the normal
RX toggling will stop the link tuner thread.
While it is possible that the link tuner thread itself
is the caller of the RX toggle (when using software
antenna diversity).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix 2 issues in antenna diversity selection.
1) the following statement will always return true.
if ((rssi_curr - rssi_old) > -5 || (rssi_curr - rssi_old) < 5)
It is cleaner to check if the absolute value is smaller then 5.
2) Only enable software diversity when default antenna setup
indicates support for it. Don't select it when the hardware
does not indicate support for it...
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
| CC drivers/net/ps3_gelic_wireless.o
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c: In function 'gelic_wl_setup_netdev_ops':
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2660: error: 'struct net_device' has no member named 'wireless_data'
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2661: error: 'struct net_device' has no member named 'wireless_handlers'
| make[3]: *** [drivers/net/ps3_gelic_wireless.o] Error 1
| make[2]: *** [drivers/net] Error 2
| make[1]: *** [drivers] Error 2
| make[1]: *** Waiting for unfinished jobs....
| make: *** [sub-make] Error 2
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Acked-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Link the net_device structure of the wireless part to the
corresponding device structure.
Without this, the sysfs node for this net_device would not have
'device' link.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is obviously wrong to use an enum in a little endian struct,
and those other enums should be declared differently.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the macvlan release I had at least 5 users asking how to configure
it since the old userspace tool doesn't work with the version in the
kernel. Add a pointer to the Kconfig help.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the Intel ICH10 SMBus Controller DeviceID's and updates
Tolapai support.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
When probing i2c-pca-isa writes to legacy ioports, which crashes the kernel
if there is no device at that port.
This patch adds a check_legacy_ioport call, so probe fails gracefully
and thus prevents the oops.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
While working on the PCA9564-platform driver, I sometimes had a glimpse at the
pxa-driver. I found some suspicious places, and this patch contains my
suggestions. Note: They are not tested, due to no hardware.
[JD: Some more fixes.]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Mike Rapoport <mike@compulab.co.il>
Tested-by: Eric Miao <ymiao3@marvell.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata-core: fix kernel-doc warning
sata_fsl: fix build with ATA_VERBOSE_DEBUG
[libata] ahci: AMD SB700/SB800 SATA support 64bit DMA
libata-pmp: clear hob for pmp register accesses
libata: automatically use DMADIR if drive/bridge requires it
power_state: get rid of write-only variable in SATA
pata_atiixp: Use 255 sector limit
Fix libata-core kernel-doc warning:
Warning(linux-2.6.25-rc2-git6//drivers/ata/libata-core.c:168): No description found for parameter 'ap'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes build and few warnings when ATA_VERBOSE_DEBUG
is defined:
CC drivers/ata/sata_fsl.o
drivers/ata/sata_fsl.c: In function ‘sata_fsl_fill_sg’:
drivers/ata/sata_fsl.c:338: warning: format ‘%x’ expects type ‘unsigned int’, but argument 3 has type ‘void *’
drivers/ata/sata_fsl.c:338: warning: format ‘%x’ expects type ‘unsigned int’, but argument 4 has type ‘struct prde *’
drivers/ata/sata_fsl.c: In function ‘sata_fsl_qc_issue’:
drivers/ata/sata_fsl.c:459: error: ‘csr_base’ undeclared (first use in this function)
drivers/ata/sata_fsl.c:459: error: (Each undeclared identifier is reported only once
drivers/ata/sata_fsl.c:459: error: for each function it appears in.)
drivers/ata/sata_fsl.c: In function ‘sata_fsl_freeze’:
drivers/ata/sata_fsl.c:525: error: ‘csr_base’ undeclared (first use in this function)
make[2]: *** [drivers/ata/sata_fsl.o] Error 1
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SB700 SATA controller can support 64 bit DMA, the previous commit
badc234157 was added with
careless reference to SB600, which should be modified by this patch.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
>> Mark Lord wrote:
>>> Tejun, I've added PMP to sata_mv, and am now trying to get it
>>> to work with a Marvell PM attached.
>>>
>>> And the behaviour I see is very bizarre.
>>>
>>> After hard+soft resets, the PM signature is found,
>>> and libata interrogates the PM registers.
>>>
>>> It successfully reads register 0, and then register 1.
>>> But all subsequent registers read out (incorrectly) as zeros.
...
This behavior has been confirmed by Marvell with a SATA analyzer.
The Marvell port-multiplier apparently likes to see clean HOB
information when accessing PMP registers.
Since sata_mv uses PIO shadow register access, this doesn't happen
automatically, as it might in a more purely FIS-based driver (eg. ahci).
One way to fix this is to flag these commands with ATA_TFLAG_LBA48,
forcing libata to write out the HOB fields with known (zero) values.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Back in 2.6.17-rc2, a libata module parameter was added for atapi_dmadir.
That's nice, but most SATA devices which need it will tell us about it
in their IDENTIFY PACKET response, as bit-15 of word-62 of the
returned data (as per ATA7, ATA8 specifications).
So for those which specify it, we should automatically use the DMADIR bit.
Otherwise, disc writing will fail by default on many SATA-ATAPI drives.
This patch adds ATA_DFLAG_DMADIR and make ata_dev_configure() set it
if atapi_dmadir is set or identify data indicates DMADIR is necessary.
atapi_xlat() is converted to check ATA_DFLAG_DMADIR before setting
DMADIR.
Original patch is from Mark Lord.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
power_state is scheduled for removal, and libata uses it in write-only
mode. Remove it.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
