Use the bark interrupt as the pre-timeout notifier whenever this
interrupt is available.
By default, the pretimeout notification shall occur one second earlier
than the timeout.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190906205411.31666-2-jorge.ramirez-ortiz@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Set WDT_CLEAR_TIMEOUT_AND_BOOT_CODE_SELECTION into WDT_CLEAR_TIMEOUT_STATUS
to clear out boot code source and re-enable access to the primary SPI flash
chip while booted via wdt2 from the alternate chip.
AST2400 datasheet says:
"In the 2nd flash booting mode, all the address mapping to CS0# would be
re-directed to CS1#. And CS0# is not accessible under this mode. To access
CS0#, firmware should clear the 2nd boot mode register in the WDT2 status
register WDT30.bit[1]."
Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190828102402.13155-4-i.mikhaylov@yadro.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The orion watchdog can either reset the CPU or generate an interrupt.
The interrupt would be useful for debugging as it provides panic()
output about the watchdog expiry, however if the interrupt is used the
watchdog can't reset the CPU in the event of being stuck in a loop with
interrupts disabled or if the CPU is prevented from accessing memory
(e.g. an unterminated DMA).
The Armada SoCs have spare timers that aren't currently used by the
Linux kernel. We can use timer1 to provide a pre-timeout ahead of the
watchdog timer and provide the possibility of gathering debug before the
reset triggers.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190829215224.27956-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The i.MX7ULP Watchdog Timer (WDOG) module is an independent timer
that is available for system use.
It provides a safety feature to ensure that software is executing
as planned and that the CPU is not stuck in an infinite loop or
executing unintended code. If the WDOG module is not serviced
(refreshed) within a certain period, it resets the MCU.
Add driver support for i.MX7ULP watchdog.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1566999303-18795-2-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The ast2600 can be supported by the same code as the ast2500.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190819051738.17370-3-joel@jms.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
There's only one user of ziirave_firm_write_block_data(), so we may as
well inline it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-22-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Bootloader firmware expects the following traffic for DOWNLOAD_END:
S Addr Wr [A] 0x10 [A] P
using ziirave_firm_write_byte() will result in
S Addr Wr [A] 0x10 [A] 0x01 [A] 0x01 [A] P
which happens to work because firmware will ignore any extra bytes
sent. Fix this by converting the code to use i2c_smbus_write_byte()
instead.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-21-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Bootloader firmware doesn't implement DOWNLOAD_START or
DOWNLOAD_PACKET in a non-blocking way. It will stretch the clock of
the first status byte read until the operation is complete. Polling
for the status is not really necessary since it will always succed on
the first try. Replace polling code with a simple single byte read to
simplify things.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-20-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Bootloader firmware expects the following traffic for
RESET_PROCESSOR:
S Addr Wr [A] 0x0b [A] 0x01 [A] P
using ziirave_firm_write_byte() will result in
S Addr Wr [A] 0x0b [A] 0x01 [A] 0x01 [A] P
which happens to work because firmware will ignore any extra bytes and
expected magic value matches byte count sent by
i2c_smbus_write_block_data(). Fix this by converting the code to use
i2c_smbus_write_byte_data() instead.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-19-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Bootloader firmware expects the following traffic for DOWNLOAD_END:
S Addr Wr [A] 0x11 [A] P
using ziirave_firm_write_byte() will result in
S Addr Wr [A] 0x11 [A] 0x01 [A] 0x01 [A] P
which happens to work because firmware will ignore any extra bytes
sent. Fix this by converting the code to use i2c_smbus_write_byte()
instead.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-18-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Bootloader firmware expects the following traffic for
JUMP_TO_BOOTLOADER:
S Addr Wr [A] 0x0c [A] 0x01 [A] P
using ziirave_firm_write_byte() will result in
S Addr Wr [A] 0x0c [A] 0x01 [A] 0x01 [A] P
which happens to work because firmware will ignore any extra bytes and
expected magic value matches byte count sent by
i2c_smbus_write_block_data(). Fix this by converting the code to use
i2c_smbus_write_byte_data() instead.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-17-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Fix misleading error message in ziirave_wdt_init_duration(). Saying
"unable to set ..." implies that an attempt at communication with
watchdog device has taken palce and was not successful. In this case,
however, all it indicates is that no reset pulse duration was
specified either via kernel parameter or Device Tree. Re-phase the log
message to be more clear about benign nature of this event.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-16-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Bootloader code will ignore any attempts to write data to any flash
area outside of [ZIIRAVE_FIRM_FLASH_MEMORY_START;
ZIIRAVE_FIRM_FLASH_MEMORY_END]. Firmware update code already have an
appropriate check to skip those areas when validating updated
firmware. Firmware programming code, OTOH, does not and will
needlessly send no-op I2C traffic. Add an appropriate check to
__ziirave_firm_write_pkt() so as to save all of that wasted effort.
While at it, normalize all of the address handling code to use full
32-bit address in units of bytes and convert it to an appropriate
value only in places where that is necessary.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-15-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
We only compare first 'len' bytes of read firmware, so we don't need
to read more that that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-14-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Ihex_next_binrec() will return NULL if next record's 'len' is zero, so
explicit checks for that in the driver are unnecessary. Drop them.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-13-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Instead of doing this explicitly use put_unaligned_le16() to place
16-bit address value into command payload.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-12-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Instead of zeroing out all of the packet and then overwriting a
significant portion of those zeros via memcpy(), zero out only a
portion of the packet that is known to not contain any data.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-11-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Both memset() and ziirave_firm_write_block_data() expect length in
bytes as an argument, not a number of elements in array. It just
happens that in this particular case both values are equal. Modify the
code to use sizeof() instead.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-10-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Zeros don't contribute anything to checksum value, so we can skip
unused portion of the packet when calculating its checksum.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-9-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
We don't need to check for packet length more than once, so drop the
extra check in ziirave_firm_upload(). While at it move the check at
the very start of __ziirave_firm_write_pkt(), as to not waste any time
preparing a packet we'll never use.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-8-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
There no reason why ziirave_firm_write_pkt() has to take firmware
data via 'struct ihex_binrec' and it can just take address, data pointer
and data length as individual arguments. Make this change to allow us
to drastically simplify handling page crossing case by removing all of
the extra code required to split 'struct ihex_binrec' into two.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-7-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Log bootloader/firmware info during probe. This information is
available via sysfs already, but it's really helpful to have this in
kernel log during startup as well.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-6-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Reprogramming bootloader on watchdog MCU will result in reported
default timeout value of "0". That in turn will be unnecessarily
rejected by the driver as invalid device (-ENODEV). Simplify probe to
read stored timeout value, set it to a sane default if it is bogus,
and then program that value unconditionally.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-5-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The driver is quite silent in case of probe failure, which makes it
more difficult to diagnose problem from the kernel log. Add logging to
all of the silent error paths ziirave_wdt_probe() to improve that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rick Ramstetter <rick@anteaterllc.com>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812200906.31344-3-andrew.smirnov@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
An error message is already displayed by watchdog_register_device()
when failed, so no need to have error log again for failure of
calling devm_watchdog_register_device().
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812084434.13316-1-Anson.Huang@nxp.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Converting from ms to s requires dividing by 1000, not multiplying. So
this is currently taking the smaller of new_timeout and 1.28e8,
i.e. effectively new_timeout.
The driver knows what it set max_hw_heartbeat_ms to, so use that
value instead of doing a division at run-time.
FWIW, this can easily be tested by booting into a busybox shell and
doing "watchdog -t 5 -T 130 /dev/watchdog" - without this patch, the
watchdog fires after 130&127 == 2 seconds.
Fixes: b07e228eee "watchdog: imx2_wdt: Fix set_timeout for big timeout values"
Cc: stable@vger.kernel.org # 5.2 plus anything the above got backported to
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190812131356.23039-1-linux@rasmusvillemoes.dk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The cpwd_compat_ioctl() contains a bogus mutex that dates
back to a leftover BKL instance.
Simplify the implementation by using the new compat_ptr_ioctl()
helper function that will do the right thing for all calls
here.
Note that WIOCSTART/WIOCSTOP don't take any arguments, so
the compat_ptr() conversion is not needed here, but it also
doesn't hurt.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190814204259.120942-6-arnd@arndb.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Commit f7a94db4e9 ("s390/watchdog: use watchdog API") converted
the driver to use the watchdog API, but some includes as well as
MODULE_ALIAS_MISCDEV() were missed.
Cc: Philipp Hachtmann <phacht@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The ARM w90x900 platform is getting removed, so this driver is obsolete
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190809202749.742267-7-arnd@arndb.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The platform is getting removed, so there are no remaining
users of this driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190809202749.742267-5-arnd@arndb.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The only thing that prevents building this driver on other
platforms is the mach/hardware.h include, which is not actually
used here at all, so remove the line and allow CONFIG_COMPILE_TEST.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20190809144043.476786-4-arnd@arndb.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Fix the following warning (Building: ci20_defconfig mips):
drivers/watchdog/jz4740_wdt.c: In function ‘jz4740_wdt_probe’:
drivers/watchdog/jz4740_wdt.c:165:6: warning: unused variable ‘ret’ [-Wunused-variable]
int ret;
^~~
Fixes: 9ee644c932 ("watchdog: jz4740_wdt: drop warning after registering device")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190806073953.GA13685@embeddedor
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-watchdog@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings (Building: sparc64):
drivers/watchdog/riowd.c: In function ‘riowd_ioctl’:
drivers/watchdog/riowd.c:136:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
riowd_writereg(p, riowd_timeout, WDTO_INDEX);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/watchdog/riowd.c:139:2: note: here
case WDIOC_GETTIMEOUT:
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190730014650.GA31309@embeddedor
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: arm):
drivers/watchdog/wdt977.c: In function ‘wdt977_ioctl’:
LD [M] drivers/media/platform/vicodec/vicodec.o
drivers/watchdog/wdt977.c:400:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
wdt977_keepalive();
^~~~~~~~~~~~~~~~~~
drivers/watchdog/wdt977.c:403:2: note: here
case WDIOC_GETTIMEOUT:
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190729223159.GA20878@embeddedor
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: i386):
drivers/watchdog/scx200_wdt.c: In function ‘scx200_wdt_ioctl’:
drivers/watchdog/scx200_wdt.c:188:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
scx200_wdt_ping();
^~~~~~~~~~~~~~~~~
drivers/watchdog/scx200_wdt.c:189:2: note: here
case WDIOC_GETTIMEOUT:
^~~~
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190729200602.GA6854@embeddedor
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/watchdog/ar7_wdt.c: warning: this statement may fall
through [-Wimplicit-fallthrough=]: => 237:3
drivers/watchdog/pcwd.c: warning: this statement may fall
through [-Wimplicit-fallthrough=]: => 653:3
drivers/watchdog/sb_wdog.c: warning: this statement may fall
through [-Wimplicit-fallthrough=]: => 204:3
drivers/watchdog/wdt.c: warning: this statement may fall
through [-Wimplicit-fallthrough=]: => 391:3
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20190729151033.GA10143@embeddedor
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
It is likely that 'ath97_wdt_shutdown()' should be 'ath79_wdt_shutdown()'
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
For spinlocks the type spinlock_t should be used instead of "struct
spinlock".
Use spinlock_t for spinlock's definition.
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Currently, the atmel-sama5d4-wdt continues to run after system suspend.
Unless the system resumes within the watchdog timeout period so the
userspace can kick it, the system will be reset. This change disables
the watchdog on suspend if it is active and re-enables on resume. These
actions occur during the late and early phases of suspend and resume
respectively to minimize chances where a lock could occur while the
watchdog is disabled.
Signed-off-by: Ken Sloat <ksloat@aampglobal.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This gets rid of the unnecessary license boilerplate, and avoids
having to deal with individual patches one by one.
No functional changes.
Reviewed-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-watchdog@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Convert those documents and prepare them to be part of the kernel
API book, as most of the stuff there are related to the
Kernel interfaces.
Still, in the future, it would make sense to split the docs,
as some of the stuff is clearly focused on sysadmin tasks.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
When the watchdog device is not open by userspace, the kernel takes
care of pinging it. When the open_timeout feature is in use, we should
ensure that the hardware fires close to open_timeout seconds after the
kernel has assumed responsibility for the device.
To do this, simply reuse the logic that is already in place for
ensuring the same thing when userspace is responsible for regularly
pinging the device:
- When watchdog_active(wdd), this patch doesn't change anything.
- When !watchdog_active(wdd), the "virtual timeout" should be taken to
be ->open_deadline". When the open_timeout feature is not used or the
device has been opened at least once, ->open_deadline is KTIME_MAX,
and the arithmetic ends up returning keepalive_interval as we used to.
This has been tested on a Wandboard with various combinations of
open_timeout and timeout-sec properties for the on-board watchdog by
booting with 'init=/bin/sh', timestamping the lines on the serial
console, and comparing the timestamp of the 'imx2-wdt 20bc000.wdog:
timeout nnn sec' line with the timestamp of the 'U-Boot SPL ...'
line (which appears just after reset).
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
