tm_wday is never checked for validity and it is not read back in
r9701_get_datetime. Avoid setting it to stop tripping static checkers:
drivers/rtc/rtc-r9701.c:109 r9701_set_datetime()
error: undefined (user controlled) shift '1 << dt->tm_wday'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201015191135.471249-4-alexandre.belloni@bootlin.com
If RV3028_CTRL1_EERD is not set (this is the default), the RTC will refresh
the RAM configuration registers from the EEPROM at midnight. It is
necessary to save the RAM registers back to EEPROM after modifying them.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201009153101.721149-4-alexandre.belloni@bootlin.com
rv3028_clkout_set_rate unconditionally sets RV3028_CLKOUT_CLKOE but
clk_set_rate may be called with the clock disabled. Ensure the clock is
kept disabled if it was not yet enabled.
Also, the actual rate was overwritten when enabling the clock, properly
write to the register only once.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201009153101.721149-1-alexandre.belloni@bootlin.com
Removing the struct member "dev" in mt6397 RTC driver because it's not
initialized and the only usage is for one debugging message.
Also fixed a typo in the error message.
Signed-off-by: Fei Shao <fshao@chromium.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201008093414.1911699-1-fshao@chromium.org
Since the switch to using regmap this function no longer takes the
I2C client struct as argument nor do we even interact with the client
anywhere other than when creating the regmap.
Rename it to a less misleading name: "rx8010_init()".
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917114656.9036-1-brgl@bgdev.pl
The ds1307 charger infrastructure now allows to add a rx8130 charger
setup that..
- does not depend on trickle-resistor-ohms
- does not use DS13XX_TRICKLE_CHARGER_MAGIC trickle-charge select (TCS)
bits
- keeps previous no-charge behavior for device trees without
aux-voltage-chargeable
Make that happen.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-9-bst@pengutronix.de
Prefer aux-voltage-chargeable over trickle-diode-disable and set diode
accordingly. This is then passed to the chip's appropriate charge setup
function.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-8-bst@pengutronix.de
Some RTC's batteries and supercaps were charged by default until now.
In contrast other RTCs allow charging but the driver did not configure
them to do so until now. These must not be charged by default to stay
backwards compatible.
In order to do that, store the charge default per chip.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-7-bst@pengutronix.de
Make trickle-resistor-ohms optional for charging setups that do not
require specifying ROUT bits (specifying the resistor value between Vcc
and Vbackup). In order to allow specifying that, introduce
requires_trickle_resistor per chip.
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-6-bst@pengutronix.de
DS13XX_TRICKLE_CHARGER_MAGIC sets the trickle-charge select (TCS) bits
(7..4). The datasheet of Maxim Integrated's DS1339 [1] for instance
reads:
"To prevent accidental enabling, only a pattern on 1010 enables the
trickle charger. All other patterns disable the trickle charger."
Since not all RTCs connected to a backup battery or supercap use these
bits DS13XX_TRICKLE_CHARGER_MAGIC should not get applied for all charger
setups unconditionally.
Epson's RX8130 is such an example: Instead of TCS bits "SMPTSEL1",
"SMPTSEL0", "CHGEN" and "INIEN" are expected as bit 7..4.
DS1339 and DS1340 are currently the only RTCs in the ds1307 driver that
apply DS13XX_TRICKLE_CHARGER_MAGIC to their setup register value. So
apply DS13XX_TRICKLE_CHARGER_MAGIC in do_trickle_setup_ds1339() which
is used by both RTCs.
[1] https://datasheets.maximintegrated.com/en/ds/DS1339-DS1339U.pdf
[2] https://support.epson.biz/td/api/doc_check.php?dl=app_RX8130CE
Signed-off-by: Bastian Krause <bst@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200917183246.19446-5-bst@pengutronix.de
Fix a bug when not specify interrupts property in dts
as follows,
rtc-pcf2127-i2c 1-0051: failed to request alarm irq
rtc-pcf2127-i2c: probe of 1-0051 failed with error -22
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200915073213.12779-1-biwen.li@oss.nxp.com
ds1685_rtc_begin_data_access() tried to access an extended register before
enabling access to it by switching to bank 1. Depending on content in NVRAM
this could lead to an endless loop. While at it fix also switch back to
bank 0 in ds1685_rtc_end_data_access().
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Joshua Kinard <kumba@gentoo.org>
Link: https://lore.kernel.org/r/20200910084124.138560-1-tsbogend@alpha.franken.de
The only usage of st_rtc_ops is to assign its address to the ops field
in the rtc_device struct. which is a const pointer. Make it const to
allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200913122644.35515-1-rikard.falkeborn@gmail.com
We don't need to check the time range manually in set_time(), we can
use range_min and range_max exposed by struct rtc_device.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-15-brgl@bgdev.pl
This driver requires SMBUS to work. We can relax this requirement if we
switch to using i2c regmap and let the regmap sub-system figure out how
to talk to the bus.
This also has the advantage of shrinking the code for register updates.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-14-brgl@bgdev.pl
We should generally use probe_new instead of probe when registering i2c
drivers. Convert rx8010 to using it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-13-brgl@bgdev.pl
Using the size of the variable is preferred over using the size of its
type when allocating memory. Convert the call to devm_kzalloc() in
probe().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-11-brgl@bgdev.pl
Simple 'dev' looks better then repeated &client->dev and has the added
benefit of avoiding unnecessary line breaks.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-10-brgl@bgdev.pl
The 'err' local variable in rx8010_init_client() doesn't need to be
initialized.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-9-brgl@bgdev.pl
The time buffer len is used directly in this driver. For readability
it's better to define it as the difference between the date register
offsets and use sizeof() whenever referencing it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-8-brgl@bgdev.pl
All other functions in this driver use 'err' for integer return values.
Do the same in rx8010_set_time() for consistency.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-7-brgl@bgdev.pl
The define values in this driver are close to their names and they are
separated by spaces. Use tabs instead and align all defines.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-6-brgl@bgdev.pl
Move local variables of the same type into a single line for better
readability.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200914154601.32245-5-brgl@bgdev.pl
The way the driver is implemented is buggy for the (admittedly unlikely)
use case where there are two RTCs with one having an interrupt configured
and the second not. This is caused by the fact that we use a global
rtc_class_ops struct which we modify depending on whether the irq number
is present or not.
Fix it by using two const ops structs with and without alarm operations.
While at it: not being able to request a configured interrupt is an error
so don't ignore it and bail out of probe().
Fixes: ed13d89b08 ("rtc: Add Epson RX8010SJ RTC driver")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200914154601.32245-2-brgl@bgdev.pl
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200830080937.14367-1-krzk@kernel.org
Original device id would conflict with crypto driver, change it.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200818063609.39859-1-ran.wang_1@nxp.com
Ensure the OSF flag is cleared on the DS1388 when the clock is set.
Fixes: df11b323b1 ("rtc: ds1307: handle oscillator failure flags for ds1388 variant")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200818013543.4283-1-chris.packham@alliedtelesis.co.nz
Similar to the other variants the DS1388 has a bit to stop the
oscillator to reduce the power consumption from VBAT. Ensure that the
oscillator is enabled when the system is up.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200816235731.21071-1-chris.packham@alliedtelesis.co.nz
rs5c313_rtc_init() calls platform_driver_register(), and initializes the
hardware. This is wrong because of two reasons:
1. As soon as the driver has been registered, the device may be
probed. If devm_rtc_device_register() is called before hardware
initialization, reading the current time will fail:
rs5c313 rs5c313: rs5c313_rtc_read_time: timeout error
rs5c313 rs5c313: registered as rtc0
rs5c313 rs5c313: rs5c313_rtc_read_time: timeout error
rs5c313 rs5c313: hctosys: unable to read the hardware clock
2. If the platform device does not exist, the driver will still write
to a hardware device that may not be present.
Fix this by moving the hardware initialization sequence to the driver's
.probe() method.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200814110731.29029-3-geert+renesas@glider.be
Commit 284e2fa1da ("rtc: rtc-rs5c313: use
devm_rtc_device_register()"), removed the last user of the
driver-specific data. Hence there is no longer a need to set it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200814110731.29029-2-geert+renesas@glider.be
cmos_read_alarm() may leave certain fields of a struct rtc_wkalrm
untouched; therefore, these fields contain garbage if not properly
initialized, leading to inconsistent values when converting into
time64_t. This patch to zero initialize the struct before calling
cmos_read_alarm().
Note that this patch is not intended to produce a correct time64_t, it
is only to produce a consistent value. In the case of suspend/resume, a
correct time64_t is not necessary; a consistent value is sufficient to
correctly perform an equality test for t_current_expires and
t_saved_expires. Logic to deduce a correct time64_t is expensive and
hence should be avoided.
Signed-off-by: Victor Ding <victording@google.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200814191654.v2.1.Iaf7638a2f2a87ff68d85fcb8dec615e41340c97f@changeid
Drivers:
- ds1374: use watchdog core
- pcf2127: add alarm and pcf2129 support
-----BEGIN PGP SIGNATURE-----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=ZEHC
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Not much this cycle - mostly non urgent driver fixes:
- ds1374: use watchdog core
- pcf2127: add alarm and pcf2129 support"
* tag 'rtc-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: pcf2127: fix alarm handling
rtc: pcf2127: add alarm support
rtc: pcf2127: add pca2129 device id
rtc: max77686: Fix wake-ups for max77620
rtc: ds1307: provide an indication that the watchdog has fired
rtc: ds1374: remove unused define
rtc: ds1374: fix RTC_DRV_DS1374_WDT dependencies
rtc: cleanup obsolete comment about struct rtc_class_ops
rtc: pl031: fix set_alarm by adding back call to alarm_irq_enable
rtc: ds1374: wdt: Use watchdog core for watchdog part
rtc: Replace HTTP links with HTTPS ones
rtc: goldfish: Enable interrupt in set_alarm() when necessary
rtc: max77686: Do not allow interrupt to fire before system resume
rtc: imxdi: fix trivial typos
rtc: cpcap: fix range
Fix multiple issues when handling alarms:
- Use threaded interrupt to avoid scheduling when atomic
- Stop matching on week day as it may not be set correctly
- Avoid parsing the DT interrupt and use what is provided by the i2c or
spi subsystem
- Avoid returning IRQ_NONE in case of error in the interrupt handler
- Never write WDTF as specified in the datasheet
- Set uie_unsupported, as for the pcf85063, setting alarms every seconds
is not working correctly and confuses the RTC.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200812085114.474903-1-alexandre.belloni@bootlin.com
The PCA2129 is the automotive grade version of the PCF2129.
add it to the list of compatibles.
Signed-off-by: Liam Beguin <lvb@xiphos.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Link: https://lore.kernel.org/r/20200630024211.12782-2-liambeguin@gmail.com
Following commit d8f090dbea ("rtc: max77686: Do not allow interrupt to
fire before system resume"), RTC wake-ups stopped working on Jetson TX2
and Jetson Xavier platforms. The Jetson TX2 uses the max77620 PMIC and
the Jetson Xavier uses max20024 PMIC. Both of these PMICs have the same
max77620 RTC controller.
For the max77620 RTC, the variable 'rtc_irq_from_platform' is defined as
true in the max77686 driver and because of this the IRQ passed to the
max77686 driver for RTC is the PMIC IRQ and not the parent. Hence,
following commit d8f090dbea ("rtc: max77686: Do not allow interrupt to
fire before system resume"), for the max77620 the RTC IRQ within the
PMIC is now getting disabled on entry to suspend and unable to wake the
system up. Fix this by only disabling interrupts on entry to suspend
in the max77686 RTC driver, if the interrupt is the parent interrupt.
Fixes: d8f090dbea ("rtc: max77686: Do not allow interrupt to fire before system resume")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200806125431.699339-1-jonathanh@nvidia.com
