When comparing hw->queues to determine if the
device is QoS capable, use IEEE80211_NUM_ACS
instead of just 4.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When adding pending SKBs there's no need to
stop all queues, we only need to stop those
that we're adding frames to. Implement that
by lazily stopping a queue as we add an SKB.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the queue status changes we need to do a fair
bit of work, so ignore no-op changes early.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we get more hardware queues, we'll still want
to only have netdev queues per AC, so set it up in
that way. If the hardware doesn't support QoS (by
not supporting at least 4 queues) the netdevs get
a single queue only (this is no change in behavior
as there are no drivers with 2 or 3 queues today.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers that don't support QoS also don't support
setting up their ACs, catch that early. While at
it, remove the input check since cfg80211 does it
now.
Also fix up the restart code to not try to set up
the queues in this case.
Finally also change the tx_conf array to have
IEEE80211_NUM_ACS entries instead of # of queues
since that's what it really needs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the plan to change mac80211's queue API to
not map ACs to queues 1:1, it seems necessary to
clarify some APIs that act on ACs rather than on
queues to spell that out explicitly. Do this.
Also verify that the AC number given is valid.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This field is never set to anything non-zero in
mac80211, so we should be able to remove it.
Unfortunately though, the iwlwifi and iwlegacy
drivers use it for their internal TX status
processing (which shouldn't be using the rate
control API to start with), so add a new field
"status.antenna" for them, at least for now.
In the future, I plan to use the new field to
hold the hardware queue, while the SKB's queue
mapping holds the AC.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Devices that have internal rate control need to be
notified when the bandwidth or SMPS state changes
just like external rate control algorithms get a
notification now.
Add this notification and clarify the change bits
while at it, the HT_CHANGED bit really meant only
bandwidth changed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently stop the queue when changing the rate
control between 20/40 MHz in the BSS. This seems to
have been necessary when we actually changed the
channel, but now that we just update the station it
doesn't seem right any more. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel type argument to the rate_update()
callback isn't really the correct way to give
the rate control algorithm about the desired
RX bandwidth of the peer.
Remove this argument, and instead update the
STA capabilities with 20/40 appropriately. The
SMPS update done by this callback works in the
same way, so this makes the callback cleaner.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Changing the channel type during operation is
confusing to some drivers and will be hard to
handle in multi-channel scenarios. Instead of
changing the channel, set it to the right HT
channel before authenticating/associating and
don't change it -- just update the 20/40 MHz
restrictions in rate control as needed when
changed by the AP.
This also fixes a problem that Paul missed in
his fix for the "regulatory makes us deaf"
issue -- when we couldn't use 40 MHz we still
associated saying we were using 40 MHz, which
could in similarly broken APs make us never
even connect successfully.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the AC constants instead of hard-coding
the numbers with comments.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a trivial wrapper function, inline it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no reason for it to not be static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up the code formatting and also replace
the constant 0 by IEEE80211_AC_VO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix bad indentation & pointless if nesting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE80211_MAX_QUEUES is an internal mac80211 value,
it is not guaranteed to be always 4. The firmware
API in mwifiex almost certainly doesn't care about
mac80211 changing though, so mwifiex shouldn't use
this value.
Maybe it should use IEEE80211_NUM_ACS instead and
that is what I'm doing here as at least that value
will probably never change, but maybe it should
have its own define instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not all devices are really capable of implementing
remain-on-channel, even if it is implemented in SW,
as they can't necessarily deal with channel changes
while associated.
Remove the WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL and add
it only if either the driver has remain_on_channel
implemented in the driver/device.
Also add it to all drivers that advertise P2P right
now since those definitely have to have it working.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In https://bugzilla.kernel.org/show_bug.cgi?id=42976, a system with driver
rtl8192se used as an AP suffers from "Out of SW-IOMMU space" errors. These
are caused by the DMA buffers used for beacons never being unmapped.
This bug was also reported at
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/961618
Reported-and-Tested-by: Da Xue <da@lessconfused.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prefix dmesg output with "iwlwifi: " by
adding #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the case of disabled CONFIG_IWLWIFI_DEBUGFS option the compiler complains
about the unused variable 'img'. Fix this by moving the 'img' definition.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Macros can be converted to functions to reduce overall object size.
Convert the ATH5K_PRINTK macro to use _ath5k_printk.
Allyesconfig size is reduced ~10%
$ size drivers/net/wireless/ath/ath5k/built-in.o*
text data bss dec hex filename
211557 2032 40672 254261 3e135 drivers/net/wireless/ath/ath5k/built-in.o.new
235412 2032 47296 284740 45844 drivers/net/wireless/ath/ath5k/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a more current logging style.
Make sure all output is prefixed appropriately.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the POWER_PMI to the op_mode where it is changed. The trans needs
to check it frequently, so shadow the status in the trans and update it
in trans when it infrequently changes.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The op_mode should check for FW_ERROR before calling send_cmd. This
removes the need to test for FW_ERROR in the trans layer.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With error logging now completely handled in
the op_mode, the transport layer does not
need to know information about the loaded
firmware.
Remove this state information from the
iwl_shared data structure.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_get_single_channel_number is used only in
iwl-scan.c, move it there and mark it static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_full_rxon_required is used only in
iwl-agn-rxon.c. Move it there and mark it
static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_check_rxon_cmd is used only in
iwl-agn-rxon.c. Move it there and mark it
static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_set_rxon_hwcrypto is used only in
iwl-agn-rxon.c. Move it there and mark it
static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_send_rxon_timing is used only in
iwl-agn-rxon.c, move it there and mark it
static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used only in one file, move it there
and make it static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This variable holds the ucode currently
running on the device; which is determined by
op_mode, so move this parameter there.
Also, the name of the variable is a bit
misleading, so rename it to cur_ucode.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Error log reporting does not belong to the
transport layer, but to the op_mode loading
the ucode, as it is the entity which knows
about the ucode loaded, and what the error
information means.
Move device logging pointers from the
transport layer to op_mode.
With this change, transport layer only
reports an error to the op_mode, which will
figure out what to do with the error. This
causes the driver to now dump out error logs
when the command queue is stuck as well.
Also, move the debugfs entry for event logs
out of the transport layer and into op_mode.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_nic_error is used in iwl-agn.c only, move
it there and make it static.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the process, make iwlagn_fw_error
a non-static function, as it is used
by more than one file.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No other component is accessing it any more,
so it can move to the correct place in priv.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue mapping is not only dynamic, it
is also dependent on the uCode, as we can
already see today with the dual-mode and
non-dual-mode being different.
Move the queue mapping out of the transport
layer and let the higher layer manage it.
Part of the transport configuration is how
to set up the queues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As idle is just a deep powersave mode for
the device, it will easily scan while idle
since that turns off powersave.
This reduces the number of commands sent
to the device when scanning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not (no longer?) used by any device
so just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is used only by 2000 class devices, but
they all use it so remove the configuration
parameter and hard-code the programming.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no device using this mechanism.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It talks about treating different uCode APIs
as different pieces of hardware which really
isn't how we handle things.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A whole bunch of messages, even some recent ones,
didn't include a trailing newline so add it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The calibration results all come in while we're
waiting for the calibration complete notification.
As a consequence, there's no need to install a
global RX handler for them, we can use the newly
extended notification wait framework for this and
make the code easier to follow.
It is now quite explicit that we are processing
the calibration results while waiting for the
complete notification, before this was implicit
and developers had to know this to understand why
we wait for the calibration complete notification
and what happens while we wait.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes, for example when we ask the uCode
for calibration, we wait for the "complete"
response while we also need the results that
are sent in other, interim, notifications.
Currently we handle this by installing an RX
handler globally, but that isn't needed as
this is the only time we want to use these
notifications.
So in order to be able to simplify at least
future code that does the same, extend the
notification wait framework to allow you to
wait for multiple commands and decide based
on the command whether the wait finished.
While at it, also fix a race that can then
become relevant -- if the wait function has
returned true once it shouldn't be called
again, today this can happen due to races
between the triggering and the wakeup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flow handler (hardware) can put multiple
frames into a single RX buffer. To handle
this, walk the RX buffer and check if there
are multiple valid packets in it.
To let the upper layer handle this correctly
introduce rxb_offset() which is needed when
we pass pages to mac80211 -- we need to know
the offset into the page there.
Also change the page handling scheme to use
refcounting. Anyone who needs a page will
"steal" it, which marks it as having been
used & refcounts it. The RX handler then has
to free its own reference and must not reuse
the page.
Finally, do not set the bit asking the FH to
give us each packet in a single buffer. This
really enables the feature.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
get rid of un-needed parameter
Change-Id: I992741e7382a3dbced7f8413bf1d5f301029d576
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add iwl_phy_db structure and API.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
