Based on patches from Sonny Rao and Milton Miller...
Combined the patches to fix up clean_tx_irq and clean_rx_irq.
The PowerPC architecture does not require loads to independent bytes
to be ordered without adding an explicit barrier.
In ixgbe_clean_rx_irq we load the status bit then load the packet data.
With packet split disabled if these loads go out of order we get a
stale packet, but we will notice the bad sequence numbers and drop it.
The problem occurs with packet split enabled where the TCP/IP header
and data are in different descriptors. If the reads go out of order
we may have data that doesn't match the TCP/IP header. Since we use
hardware checksumming this bad data is never verified and it makes it
all the way to the application.
This bug was found during stress testing and adding this barrier has
been shown to fix it. The bug can manifest as a data integrity issue
(bad payload data) or as a BUG in skb_pull().
This was a nasty bug to hunt down, if people agree with the fix I think
it's a candidate for stable.
Previously Submitted to e1000-devel only for ixgbe
http://marc.info/?l=e1000-devel&m=126593062701537&w=3
We've now seen this problem hit with other device drivers (e1000e mostly)
So I'm resubmitting with fixes for other Intel Device Drivers with
similar issues.
CC: Milton Miller <miltonm@bga.com>
CC: Anton Blanchard <anton@samba.org>
CC: Sonny Rao <sonnyrao@us.ibm.com>
CC: stable <stable@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing stops the workqueue being left to run in parallel with close or a
few other operations. This causes double unmaps and the like.
See kerneloops.org #1041230 for an example
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert DPRINTK, commonly used for debugging, to netif_<level>
Remove #define PFX
Use #define pr_fmt
Consistently use no periods for non-sentence logging messages
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PCI pool changes were added to fix resume failures:
commit 98468efddb
e100: Use pci pool to work around GFP_ATOMIC order 5 memory allocation failu
and
commit 70abc8cb90
e100: Fix broken cbs accounting due to missing memset.
This introduced a problem that can happen if the TX ring size
is increased. We need to size the PCI pool using cbs->max
instead of the default cbs->count value.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Stern noticed that e100 caused slab corruption.
commit 98468efddb changed
the allocation of cbs to use dma pools that don't return zeroed memory,
especially the cb->status field used to track which cb to clean, causing
(the visible) double freeing of skbs and a wrong free cbs count.
Now the cbs are explicitly zeroed at allocation time.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Roger Oksanen <roger.oksanen@cs.helsinki.fi>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_alloc_consistent uses GFP_ATOMIC allocation that may fail on some systems
with limited memory (Bug #14265). pci_pool_alloc allows waiting with
GFP_KERNEL.
Tested-by: Karol Lewandowski <karol.k.lewandowski@gmail.com>
Signed-off-by: Roger Oksanen <roger.oksanen@cs.helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
A change in how PHYs are electrically isolated caused all PHYs to be
isolated followed by reverting that isolation for the selected PHY.
Unfortunately, isolating the selected PHY for even a short period of
time can result in DHCP negotiation taking more than 10 seconds on certain
embedded configurations delaying boot time as reported by Bernhard Kaindl.
This patch reverts the change to how PHYs are isolated yet still works
around the issue for 82552 needing the selected PHY's BMCR register to
be written after the unused PHYs are isolated. This code is moved below
the setting of nic->phy ID in order to do the 82552-specific workaround.
Cc: Bernhard Kaindl <bernhard.kaindl@gmx.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devices with loadable firmware must have their firmware reloaded
after the system resumes from sleep, but the request_firmare()
API is not available at this point in the resume flow because
tasks are not yet running, and the system will hang if it is
called. Work around this issue by only calling request_firmware()
for a device's first firmware load, and cache a copy of the pointer
to the firmware blob for that device, so that we may reload firmware
images even during resume.
Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Get rid of some bogus return wrapping as well.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
E100 places it's RX packet descriptors inside skb->data and uses them
with bidirectional streaming DMA mapping. Data in descriptors is
accessed simultaneously by the chip (writing status and size when
a packet is received) and CPU (reading to check if the packet was
received). This isn't a valid usage of PCI DMA API, which requires use
of the coherent (consistent) memory for such purpose. Unfortunately e100
chips working in "simplified" RX mode have to store received data
directly after the descriptor. Fixing the driver to conform to the API
would require using unsupported "flexible" RX mode or receiving data
into a coherent memory and using CPU to copy it to network buffers.
This patch, while not yet making the driver conform to the PCI DMA API,
allows it to work correctly on X86 with swiotlb (while not breaking
other architectures).
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
E100 places it's RX packet descriptors inside skb->data and uses them
with bidirectional streaming DMA mapping. Unfortunately it fails to
transfer skb->data ownership to the device after it reads the
descriptor's status, breaking on non-coherent (e.g., ARM) platforms.
This have to be converted to use coherent memory for the descriptors.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the adapter is not power-manageable using either ACPI, or the
native PCI PM interface, __e100_power_off() returns error code, which
causes every attempt to suspend to fail, although it should return 0
in such a case. Fix this problem by ignoring the return value of
pci_set_power_state() in __e100_power_off().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert magic values 1 and -1 to NETDEV_TX_BUSY and NETDEV_TX_LOCKED respectively.
0 (NETDEV_TX_OK) is not changed to keep the noise down, except in very few cases
where its in direct proximity to one of the other values.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restore support for cards with MII-lacking PHYs as compared to removed
pre-2.6.29 eepro100 driver: use full low-level MII I/O access abstraction
by providing clean PHY-specific mdio_ctrl() functions for either standard
MII-compliant cards, slightly special ones or non-MII PHY ones.
We now have another netdev_priv member for mdio_ctrl(), thus we have some
array indirection, but we save some additional opcodes for specific
phy_82552_v handling in the common case.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Andreas Mohr <andi@lisas.de>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
BUG_ON(!test_bit(NAPI_STATE_SCHED, &n->state)) was being hit
during e100 EEH recovery. The problem source was a napi_enable
call being made during e100_io_error_detected. Napi should remain
disabled after e100_down, and only be reenabled when the interface
is recovered.
This patch also updates e100_io_error_detected in order to make
it similar to the current versions of the error_detected callback
in drivers such as e1000e and ixgbe.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After experimenting with kexec with the last merges after 2.6.29, I've
had some problems when probing e100. It would not read the eeprom. After
some bisects, I realized this has been like that since forever (at least
2.6.18). The problem is that shutdown is doing the same thing that
suspend does and puts the device in D3 state. I couldn't find a way to
get the device back to a sane state in the probe function. So, based on
some similar patches from Rafael J. Wysocki for e1000, e1000e, and ixgbe,
I wrote this one for e100.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch enables support for the new Intel 82552 adapter (new PHY paired
with the existing MAC in the ICH7 chipset). No new features are added to
the driver, however there are minor changes due to updated registers and a
few workarounds for hardware errata.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to David Woodhouse for help.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing space after if, switch, for and while keywords.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use. This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to new network device ops interface. Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The e100 driver triggers BUG_ON(buf->direction != dir)
by doing pci_map_single(..., PCI_DMA_BIDIRECTIONAL)
and pci_dma_sync_single_for_device(..., PCI_DMA_TODEVICE).
Changing the DMA direction, especially with dmabounce will result
in unexpected behaviour.
Reported-by: Anders Grafstrom <grfstrm@users.sourceforge.net>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt the e100 driver to the reworked PCI PM
* Use the observation that it is sufficient to call pci_enable_wake()
once, unless it fails
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Frans Pop <elendil@planet.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently e100 uses pci_enable_wake() to clear pending wake-up events
and disable PME# during intitialization, but that function is not
suitable for this purpose, because it immediately returns error code
if device_may_wakeup() returns false for given device.
Make e100 use pci_pme_active(), which carries out exactly the
required operations, instead.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
