Here are some small fixes for reported problems for tty and serial
drivers for 5.13-rc4.
They consist of:
- 8250 bugfixes and new device support
- lockdown security mode fixup
- syzbot found problems fixed
- 8250_omap fix for interrupt storm
- revert of 8250_omap driver fix as it caused worse problem than
the original issue
All but the last patch have been in linux-next for a while, the last one
is a revert of a problem found in linux-next with the 8250_omap driver
change.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYLJODQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yna7gCgmKIssymva29JpQb54HuzRooD8jcAn3XeMVWI
E4TQzaTFC1mNAQy8GU4F
=cLjq
-----END PGP SIGNATURE-----
Merge tag 'tty-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver fixes from Greg KH:
"Here are some small fixes for reported problems for tty and serial
drivers for 5.13-rc4.
They consist of:
- 8250 bugfixes and new device support
- lockdown security mode fixup
- syzbot found problems fixed
- 8250_omap fix for interrupt storm
- revert of 8250_omap driver fix as it caused worse problem than the
original issue
All but the last patch have been in linux-next for a while, the last
one is a revert of a problem found in linux-next with the 8250_omap
driver change"
* tag 'tty-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250: 8250_omap: Fix possible interrupt storm"
serial: 8250_pci: handle FL_NOIRQ board flag
serial: rp2: use 'request_firmware' instead of 'request_firmware_nowait'
serial: 8250_pci: Add support for new HPE serial device
serial: 8250: 8250_omap: Fix possible interrupt storm
serial: 8250: Use BIT(x) for UART_{CAP,BUG}_*
serial: 8250: Add UART_BUG_TXRACE workaround for Aspeed VUART
serial: 8250_dw: Add device HID for new AMD UART controller
serial: sh-sci: Fix off-by-one error in FIFO threshold register setting
serial: core: fix suspicious security_locked_down() call
serial: tegra: Fix a mask operation that is always true
This reverts commit 31fae7c8b1.
Tony writes:
I just noticed this causes the following regression in Linux
next when pressing a key on uart console after boot at least on
omap3. This seems to happen on serial_port_in(port, UART_RX) in
the quirk handling.
So let's drop this.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/YLCCJzkkB4N7LTQS@atomide.com
Fixes: 31fae7c8b1 ("serial: 8250: 8250_omap: Fix possible interrupt storm")
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 8428413b1d ("serial: 8250_pci: Implement MSI(-X) support")
the way the irq gets allocated was changed. With that change the
handling FL_NOIRQ got lost. Restore the old behaviour.
Fixes: 8428413b1d ("serial: 8250_pci: Implement MSI(-X) support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Link: https://lore.kernel.org/r/20210527095529.26281-1-christian.gmeiner@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is a big set of char/misc/other driver fixes for 5.13-rc3.
The majority here is the fallout of the umn.edu re-review of all prior
submissions. That resulted in a bunch of reverts along with the
"correct" changes made, such that there is no regression of any of the
potential fixes that were made by those individuals. I would like to
thank the over 80 different developers who helped with the review and
fixes for this mess.
Other than that, there's a few habanna driver fixes for reported issues,
and some dyndbg fixes for reported problems.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYKZCBg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynhRQCdGk6ri4oluyn/Z/2KAjvXDOmTmvgAn12VP42d
S1Zmh4qRH2OWaLOBg7c2
=qtxj
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here is a big set of char/misc/other driver fixes for 5.13-rc3.
The majority here is the fallout of the umn.edu re-review of all prior
submissions. That resulted in a bunch of reverts along with the
"correct" changes made, such that there is no regression of any of the
potential fixes that were made by those individuals. I would like to
thank the over 80 different developers who helped with the review and
fixes for this mess.
Other than that, there's a few habanna driver fixes for reported
issues, and some dyndbg fixes for reported problems.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (82 commits)
misc: eeprom: at24: check suspend status before disable regulator
uio_hv_generic: Fix another memory leak in error handling paths
uio_hv_generic: Fix a memory leak in error handling paths
uio/uio_pci_generic: fix return value changed in refactoring
Revert "Revert "ALSA: usx2y: Fix potential NULL pointer dereference""
dyndbg: drop uninformative vpr_info
dyndbg: avoid calling dyndbg_emit_prefix when it has no work
binder: Return EFAULT if we fail BINDER_ENABLE_ONEWAY_SPAM_DETECTION
cdrom: gdrom: initialize global variable at init time
brcmfmac: properly check for bus register errors
Revert "brcmfmac: add a check for the status of usb_register"
video: imsttfb: check for ioremap() failures
Revert "video: imsttfb: fix potential NULL pointer dereferences"
net: liquidio: Add missing null pointer checks
Revert "net: liquidio: fix a NULL pointer dereference"
media: gspca: properly check for errors in po1030_probe()
Revert "media: gspca: Check the return value of write_bridge for timeout"
media: gspca: mt9m111: Check write_bridge for timeout
Revert "media: gspca: mt9m111: Check write_bridge for timeout"
media: dvb: Add check on sp8870_readreg return
...
Add support for new HPE serial device. It is MSI enabled,
but otherwise similar to legacy HP server serial devices.
Tested-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Randy Wright <rwright@hpe.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1621009614-28836-1-git-send-email-rwright@hpe.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that RX TIMEOUT is signalled after RX FIFO has been
drained, in which case a dummy read of RX FIFO is required to clear RX
TIMEOUT condition. Otherwise, RX TIMEOUT condition is not cleared
leading to an interrupt storm
Cc: stable@vger.kernel.org
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210511151955.28071-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aspeed Virtual UARTs directly bridge e.g. the system console UART on the
LPC bus to the UART interface on the BMC's internal APB. As such there's
no RS-232 signalling involved - the UART interfaces on each bus are
directly connected as the producers and consumers of the one set of
FIFOs.
The APB in the AST2600 generally runs at 100MHz while the LPC bus peaks
at 33MHz. The difference in clock speeds exposes a race in the VUART
design where a Tx data burst on the APB interface can result in a byte
lost on the LPC interface. The symptom is LSR[DR] remains clear on the
LPC interface despite data being present in its Rx FIFO, while LSR[THRE]
remains clear on the APB interface as the host has not consumed the data
the BMC has transmitted. In this state, the UART has stalled and no
further data can be transmitted without manual intervention (e.g.
resetting the FIFOs, resulting in loss of data).
The recommended work-around is to insert a read cycle on the APB
interface between writes to THR.
Cc: ChiaWei Wang <chiawei_wang@aspeedtech.com>
Tested-by: ChiaWei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210520021334.497341-2-andrew@aj.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core ignores the return value of struct bus_type::remove()
because there is only little that can be done. To simplify the quest to
make this function return void, let struct vio_driver::remove() return
void, too. All users already unconditionally return 0, this commit makes
it obvious that returning an error code is a bad idea and should prevent
that future driver authors consider returning an error code.
Note there are two nominally different implementations for a vio bus:
one in arch/sparc/kernel/vio.c and the other in
arch/powerpc/platforms/pseries/vio.c. This patch only addresses the
former.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210505201449.195627-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Merge VT_RESIZEX fixes from Maciej Rozycki:
"I got to the bottom of the issue with VT_RESIZEX recently discussed
and came up with this small patch series, fixing an additional issue
that I originally thought might be broken VGA hardware emulation with
my laptop, which however turned out to be intertwined with the
original problem and also a regression introduced somewhat later.
The fix for that because the first patch, and then to make backporting
feasible I had to put a revert of the offending change from last
September next, followed by a proper fix for the framebuffer issue
that change had tried to address.
See individual change descriptions for details.
These have been verified with true VGA hardware (a Trident TVGA8900
ISA video adapter) using various combinations of `svgatextmode' and
`setfont' command invocations to change both the VT size and the font
size, and also switching between the text console and X11, both by
starting/stopping the X server and by switching between VTs.
All this to ensure bringing the behaviour of VGA text console back to
correct operation as it used to be with Linux 2.6.18"
* emailed patches from Maciej W. Rozycki <macro@orcam.me.uk>:
vt: Fix character height handling with VT_RESIZEX
vt_ioctl: Revert VT_RESIZEX parameter handling removal
vgacon: Record video mode changes with VT_RESIZEX
Restore the original intent of the VT_RESIZEX ioctl's `v_clin' parameter
which is the number of pixel rows per character (cell) rather than the
height of the font used.
For framebuffer devices the two values are always the same, because the
former is inferred from the latter one. For VGA used as a true text
mode device these two parameters are independent from each other: the
number of pixel rows per character is set in the CRT controller, while
font height is in fact hardwired to 32 pixel rows and fonts of heights
below that value are handled by padding their data with blanks when
loaded to hardware for use by the character generator. One can change
the setting in the CRT controller and it will update the screen contents
accordingly regardless of the font loaded.
The `v_clin' parameter is used by the `vgacon' driver to set the height
of the character cell and then the cursor position within. Make the
parameter explicit then, by defining a new `vc_cell_height' struct
member of `vc_data', set it instead of `vc_font.height' from `v_clin' in
the VT_RESIZEX ioctl, and then use it throughout the `vgacon' driver
except where actual font data is accessed which as noted above is
independent from the CRTC setting.
This way the framebuffer console driver is free to ignore the `v_clin'
parameter as irrelevant, as it always should have, avoiding any issues
attempts to give the parameter a meaning there could have caused, such
as one that has led to commit 988d076336 ("vt_ioctl: make VT_RESIZEX
behave like VT_RESIZE"):
"syzbot is reporting UAF/OOB read at bit_putcs()/soft_cursor() [1][2],
for vt_resizex() from ioctl(VT_RESIZEX) allows setting font height
larger than actual font height calculated by con_font_set() from
ioctl(PIO_FONT). Since fbcon_set_font() from con_font_set() allocates
minimal amount of memory based on actual font height calculated by
con_font_set(), use of vt_resizex() can cause UAF/OOB read for font
data."
The problem first appeared around Linux 2.5.66 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit 9736a3546de7 ("Merge with Linux 2.5.66."), where VT_RESIZEX
code in `vt_ioctl' was updated as follows:
if (clin)
- video_font_height = clin;
+ vc->vc_font.height = clin;
making the parameter apply to framebuffer devices as well, perhaps due
to the use of "font" in the name of the original `video_font_height'
variable. Use "cell" in the new struct member then to avoid ambiguity.
References:
[1] https://syzkaller.appspot.com/bug?id=32577e96d88447ded2d3b76d71254fb855245837
[2] https://syzkaller.appspot.com/bug?id=6b8355d27b2b94fb5cedf4655e3a59162d9e48e3
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert the removal of code handling extra VT_RESIZEX ioctl's parameters
beyond those that VT_RESIZE supports, fixing a functional regression
causing `svgatextmode' not to resize the VT anymore.
As a consequence of the reverted change when the video adapter is
reprogrammed from the original say 80x25 text mode using a 9x16
character cell (720x400 pixel resolution) to say 80x37 text mode and the
same character cell (720x592 pixel resolution), the VT geometry does not
get updated and only upper two thirds of the screen are used for the VT,
and the lower part remains blank. The proportions change according to
text mode geometries chosen.
Revert the change verbatim then, bringing back previous VT resizing.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 988d076336 ("vt_ioctl: make VT_RESIZEX behave like VT_RESIZE")
Cc: stable@vger.kernel.org # v5.10+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The macro "spi_register_driver" invokes the function
"__spi_register_driver()" which has a return type of int and can fail,
returning a negative value in such a case. This is currently ignored and
the init() function yields success even if the spi driver failed to
register.
Fix this by collecting the return value of "__spi_register_driver()" and
also unregister the uart driver in case of failure.
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Atul Gopinathan <atulgopinathan@gmail.com>
Link: https://lore.kernel.org/r/20210503115736.2104747-12-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 51f689cc11.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
This change did not properly unwind from the error condition, so it was
not correct.
Cc: Kangjie Lu <kjlu@umn.edu>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-11-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 32f4717983.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be not be needed at all as the
change was useless because this function can only be called when
of_match_device matched on something. So it should be reverted.
Cc: Aditya Pakki <pakki001@umn.edu>
Cc: stable <stable@vger.kernel.org>
Fixes: 32f4717983 ("serial: mvebu-uart: Fix to avoid a potential NULL pointer dereference")
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-6-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device HID AMDI0022 to the AMD UART controller driver match table
and create a platform device for it. This controller can be found on
Microsoft Surface Laptop 4 devices and seems similar enough that we can
just copy the existing AMDI0020 entries.
Cc: <stable@vger.kernel.org> # 5.10+
Tested-by: Sachi King <nakato@nakato.io>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com> # for 8250_dw part
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/20210512210413.1982933-1-luzmaximilian@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Receive FIFO Data Count Trigger field (RTRG[6:0]) in the Receive
FIFO Data Count Trigger Register (HSRTRGR) of HSCIF can only hold values
ranging from 0-127. As the FIFO size is equal to 128 on HSCIF, the user
can write an out-of-range value, touching reserved bits.
Fix this by limiting the trigger value to the FIFO size minus one.
Reverse the order of the checks, to avoid rx_trig becoming zero if the
FIFO size is one.
Note that this change has no impact on other SCIF variants, as their
maximum supported trigger value is lower than the FIFO size anyway, and
the code below takes care of enforcing these limits.
Fixes: a380ed461f ("serial: sh-sci: implement FIFO threshold register setting")
Reported-by: Linh Phung <linh.phung.jy@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/5eff320aef92ffb33d00e57979fd3603bbb4a70f.1620648218.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit that added this check did so in a very strange way - first
security_locked_down() is called, its value stored into retval, and if
it's nonzero, then an additional check is made for (change_irq ||
change_port), and if this is true, the function returns. However, if
the goto exit branch is not taken, the code keeps the retval value and
continues executing the function. Then, depending on whether
uport->ops->verify_port is set, the retval value may or may not be reset
to zero and eventually the error value from security_locked_down() may
abort the function a few lines below.
I will go out on a limb and assume that this isn't the intended behavior
and that an error value from security_locked_down() was supposed to
abort the function only in case (change_irq || change_port) is true.
Note that security_locked_down() should be called last in any series of
checks, since the SELinux implementation of this hook will do a check
against the policy and generate an audit record in case of denial. If
the operation was to carry on after calling security_locked_down(), then
the SELinux denial record would be bogus.
See commit 59438b4647 ("security,lockdown,selinux: implement SELinux
lockdown") for how SELinux implements this hook.
Fixes: 794edf30ee ("lockdown: Lock down TIOCSSERIAL")
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210507115719.140799-1-omosnace@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the expression lsr | UART_LSR_TEMT is always true and
this seems suspect. I believe the intent was to mask lsr with UART_LSR_TEMT
to check that bit, so the expression should be using the & operator
instead. Fix this.
Fixes: b9c2470fb1 ("serial: tegra: flush the RX fifo on frame error")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210426105514.23268-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pattern prefixed with '/' matches files in the same directory,
but not ones in sub-directories.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Miguel Ojeda <ojeda@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Andra Paraschiv <andraprs@amazon.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Gabriel Krisman Bertazi <krisman@collabora.com>
- Add idle states table for IceLake-D to the intel_idle driver and
update IceLake-X C6 data in it (Artem Bityutskiy).
- Fix the C7 idle state on Tegra114 in the tegra cpuidle driver and
drop the unused do_idle() firmware call from it (Dmitry Osipenko).
- Fix cpuidle-qcom-spm Kconfig entry (He Ying).
- Fix handling of possible negative tick_nohz_get_next_hrtimer()
return values of in cpuidle governors (Rafael Wysocki).
- Add support for frequency-invariance to the ACPI CPPC cpufreq
driver and update the frequency-invariance engine (FIE) to use it
as needed (Viresh Kumar).
- Simplify the default delay_us setting in the ACPI CPPC cpufreq
driver (Tom Saeger).
- Clean up frequency-related computations in the intel_pstate
cpufreq driver (Rafael Wysocki).
- Fix TBG parent setting for load levels in the armada-37xx
cpufreq driver and drop the CPU PM clock .set_parent method for
armada-37xx (Marek Behún).
- Fix multiple issues in the armada-37xx cpufreq driver (Pali Rohár).
- Fix handling of dev_pm_opp_of_cpumask_add_table() return values
in cpufreq-dt to take the -EPROBE_DEFER one into acconut as
appropriate (Quanyang Wang).
- Fix format string in ia64-acpi-cpufreq (Sergei Trofimovich).
- Drop the unused for_each_policy() macro from cpufreq (Shaokun
Zhang).
- Simplify computations in the schedutil cpufreq governor to avoid
unnecessary overhead (Yue Hu).
- Fix typos in the s5pv210 cpufreq driver (Bhaskar Chowdhury).
- Fix cpufreq documentation links in Kconfig (Alexander Monakov).
- Fix PCI device power state handling in pci_enable_device_flags()
to avoid issuse in some cases when the device depends on an ACPI
power resource (Rafael Wysocki).
- Add missing documentation of pm_runtime_resume_and_get() (Alan
Stern).
- Add missing static inline stub for pm_runtime_has_no_callbacks()
to pm_runtime.h and drop the unused try_to_freeze_nowarn()
definition (YueHaibing).
- Drop duplicate struct device declaration from pm.h and fix a
structure type declaration in intel_rapl.h (Wan Jiabing).
- Use dev_set_name() instead of an open-coded equivalent of it in
the wakeup sources code and drop a redundant local variable
initialization from it (Andy Shevchenko, Colin Ian King).
- Use crc32 instead of md5 for e820 memory map integrity check
during resume from hibernation on x86 (Chris von Recklinghausen).
- Fix typos in comments in the system-wide and hibernation support
code (Lu Jialin).
- Modify the generic power domains (genpd) code to avoid resuming
devices in the "prepare" phase of system-wide suspend and
hibernation (Ulf Hansson).
- Add Hygon Fam18h RAPL support to the intel_rapl power capping
driver (Pu Wen).
- Add MAINTAINERS entry for the dynamic thermal power management
(DTPM) code (Daniel Lezcano).
- Add devm variants of operating performance points (OPP) API
functions and switch over some users of the OPP framework to
the new resource-managed API (Yangtao Li and Dmitry Osipenko).
- Update devfreq core:
* Register devfreq devices as cooling devices on demand (Daniel
Lezcano).
* Add missing unlock opeation in devfreq_add_device() (Lukasz
Luba).
* Use the next frequency as resume_freq instead of the previous
frequency when using the opp-suspend property (Dong Aisheng).
* Check get_dev_status in devfreq_update_stats() (Dong Aisheng).
* Fix set_freq path for the userspace governor in Kconfig (Dong
Aisheng).
* Remove invalid description of get_target_freq() (Dong Aisheng).
- Update devfreq drivers:
* imx8m-ddrc: Remove imx8m_ddrc_get_dev_status() and unneeded
of_match_ptr() (Dong Aisheng, Fabio Estevam).
* rk3399_dmc: dt-bindings: Add rockchip,pmu phandle and drop
references to undefined symbols (Enric Balletbo i Serra, Gaël
PORTAY).
* rk3399_dmc: Use dev_err_probe() to simplify the code (Krzysztof
Kozlowski).
* imx-bus: Remove unneeded of_match_ptr() (Fabio Estevam).
- Fix kernel-doc warnings in three places (Pierre-Louis Bossart).
- Fix typo in the pm-graph utility code (Ricardo Ribalda).
-----BEGIN PGP SIGNATURE-----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=t+SG
-----END PGP SIGNATURE-----
Merge tag 'pm-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add some new hardware support (for example, IceLake-D idle
states in intel_idle), fix some issues (for example, the handling of
negative "sleep length" values in cpuidle governors), add new
functionality to the existing drivers (for example, scale-invariance
support in the ACPI CPPC cpufreq driver) and clean up code all over.
Specifics:
- Add idle states table for IceLake-D to the intel_idle driver and
update IceLake-X C6 data in it (Artem Bityutskiy).
- Fix the C7 idle state on Tegra114 in the tegra cpuidle driver and
drop the unused do_idle() firmware call from it (Dmitry Osipenko).
- Fix cpuidle-qcom-spm Kconfig entry (He Ying).
- Fix handling of possible negative tick_nohz_get_next_hrtimer()
return values of in cpuidle governors (Rafael Wysocki).
- Add support for frequency-invariance to the ACPI CPPC cpufreq
driver and update the frequency-invariance engine (FIE) to use it
as needed (Viresh Kumar).
- Simplify the default delay_us setting in the ACPI CPPC cpufreq
driver (Tom Saeger).
- Clean up frequency-related computations in the intel_pstate cpufreq
driver (Rafael Wysocki).
- Fix TBG parent setting for load levels in the armada-37xx cpufreq
driver and drop the CPU PM clock .set_parent method for armada-37xx
(Marek Behún).
- Fix multiple issues in the armada-37xx cpufreq driver (Pali Rohár).
- Fix handling of dev_pm_opp_of_cpumask_add_table() return values in
cpufreq-dt to take the -EPROBE_DEFER one into acconut as
appropriate (Quanyang Wang).
- Fix format string in ia64-acpi-cpufreq (Sergei Trofimovich).
- Drop the unused for_each_policy() macro from cpufreq (Shaokun
Zhang).
- Simplify computations in the schedutil cpufreq governor to avoid
unnecessary overhead (Yue Hu).
- Fix typos in the s5pv210 cpufreq driver (Bhaskar Chowdhury).
- Fix cpufreq documentation links in Kconfig (Alexander Monakov).
- Fix PCI device power state handling in pci_enable_device_flags() to
avoid issuse in some cases when the device depends on an ACPI power
resource (Rafael Wysocki).
- Add missing documentation of pm_runtime_resume_and_get() (Alan
Stern).
- Add missing static inline stub for pm_runtime_has_no_callbacks() to
pm_runtime.h and drop the unused try_to_freeze_nowarn() definition
(YueHaibing).
- Drop duplicate struct device declaration from pm.h and fix a
structure type declaration in intel_rapl.h (Wan Jiabing).
- Use dev_set_name() instead of an open-coded equivalent of it in the
wakeup sources code and drop a redundant local variable
initialization from it (Andy Shevchenko, Colin Ian King).
- Use crc32 instead of md5 for e820 memory map integrity check during
resume from hibernation on x86 (Chris von Recklinghausen).
- Fix typos in comments in the system-wide and hibernation support
code (Lu Jialin).
- Modify the generic power domains (genpd) code to avoid resuming
devices in the "prepare" phase of system-wide suspend and
hibernation (Ulf Hansson).
- Add Hygon Fam18h RAPL support to the intel_rapl power capping
driver (Pu Wen).
- Add MAINTAINERS entry for the dynamic thermal power management
(DTPM) code (Daniel Lezcano).
- Add devm variants of operating performance points (OPP) API
functions and switch over some users of the OPP framework to the
new resource-managed API (Yangtao Li and Dmitry Osipenko).
- Update devfreq core:
* Register devfreq devices as cooling devices on demand (Daniel
Lezcano).
* Add missing unlock opeation in devfreq_add_device() (Lukasz
Luba).
* Use the next frequency as resume_freq instead of the previous
frequency when using the opp-suspend property (Dong Aisheng).
* Check get_dev_status in devfreq_update_stats() (Dong Aisheng).
* Fix set_freq path for the userspace governor in Kconfig (Dong
Aisheng).
* Remove invalid description of get_target_freq() (Dong Aisheng).
- Update devfreq drivers:
* imx8m-ddrc: Remove imx8m_ddrc_get_dev_status() and unneeded
of_match_ptr() (Dong Aisheng, Fabio Estevam).
* rk3399_dmc: dt-bindings: Add rockchip,pmu phandle and drop
references to undefined symbols (Enric Balletbo i Serra, Gaël
PORTAY).
* rk3399_dmc: Use dev_err_probe() to simplify the code (Krzysztof
Kozlowski).
* imx-bus: Remove unneeded of_match_ptr() (Fabio Estevam).
- Fix kernel-doc warnings in three places (Pierre-Louis Bossart).
- Fix typo in the pm-graph utility code (Ricardo Ribalda)"
* tag 'pm-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (74 commits)
PM: wakeup: remove redundant assignment to variable retval
PM: hibernate: x86: Use crc32 instead of md5 for hibernation e820 integrity check
cpufreq: Kconfig: fix documentation links
PM: wakeup: use dev_set_name() directly
PM: runtime: Add documentation for pm_runtime_resume_and_get()
cpufreq: intel_pstate: Simplify intel_pstate_update_perf_limits()
cpufreq: armada-37xx: Fix module unloading
cpufreq: armada-37xx: Remove cur_frequency variable
cpufreq: armada-37xx: Fix determining base CPU frequency
cpufreq: armada-37xx: Fix driver cleanup when registration failed
clk: mvebu: armada-37xx-periph: Fix workaround for switching from L1 to L0
clk: mvebu: armada-37xx-periph: Fix switching CPU freq from 250 Mhz to 1 GHz
cpufreq: armada-37xx: Fix the AVS value for load L1
clk: mvebu: armada-37xx-periph: remove .set_parent method for CPU PM clock
cpufreq: armada-37xx: Fix setting TBG parent for load levels
cpuidle: Fix ARM_QCOM_SPM_CPUIDLE configuration
cpuidle: tegra: Remove do_idle firmware call
cpuidle: tegra: Fix C7 idling state on Tegra114
PM: sleep: fix typos in comments
cpufreq: Remove unused for_each_policy macro
...
Updates for SoC specific drivers include a few subsystems that
have their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance optimized
for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target module
has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to avoid
issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as we
now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and dra7
- omap-prm driver needs to enable autoidle retention support for omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of using
builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=iidq
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Updates for SoC specific drivers include a few subsystems that have
their own maintainers but send them through the soc tree:
TEE/OP-TEE:
- Add tracepoints around calls to secure world
Memory controller drivers:
- Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
- Add debug statistics to Tegra20 memory controller
- Update Tegra bindings and convert to dtschema
ARM SCMI Firmware:
- Support for modular SCMI protocols and vendor specific extensions
- New SCMI IIO driver
- Per-cpu DVFS
The other driver changes are all from the platform maintainers
directly and reflect the drivers that don't fit into any other
subsystem as well as treewide changes for a particular platform.
SoCFPGA:
- Various cleanups contributed by Krzysztof Kozlowski
Mediatek:
- add MT8183 support to mutex driver
- MMSYS: use per SoC array to describe the possible routing
- add MMSYS support for MT8183 and MT8167
- add support for PMIC wrapper with integrated arbiter
- add support for MT8192/MT6873
Tegra:
- Bug fixes to PMC and clock drivers
NXP/i.MX:
- Update SCU power domain driver to keep console domain power on.
- Add missing ADC1 power domain to SCU power domain driver.
- Update comments for single global power domain in SCU power domain
driver.
- Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance
optimized for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers
OMAP:
- Preparation to use devicetree for genpd
- ti-sysc needs iorange check improved when the interconnect target
module has no control registers listed
- ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to
avoid issues with missing resources and unnecessary deferred probe
- ti-sysc debug option can now detect more devices
- ti-sysc now warns if an old incomplete devicetree data is found as
we now rely on it being complete for am3 and 4
- soc init code needs to check for prcm and prm nodes for omap4/5 and
dra7
- omap-prm driver needs to enable autoidle retention support for
omap4
- omap5 clocks are missing gpmc and ocmc clock registers
- pci-dra7xx now needs to use builtin_platform_driver instead of
using builtin_platform_driver_probe for deferred probe to work
Raspberry Pi:
- Fix-up all RPi firmware drivers so as for unbind to happen in an
orderly fashion
- Support for RPi's PoE hat PWM bus
Qualcomm
- Improved detection for SCM calling conventions
- Support for OEM specific wifi firmware path
- Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP"
* tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
soc: aspeed: fix a ternary sign expansion bug
memory: mtk-smi: Add device-link between smi-larb and smi-common
memory: samsung: exynos5422-dmc: handle clk_set_parent() failure
memory: renesas-rpc-if: fix possible NULL pointer dereference of resource
clk: socfpga: fix iomem pointer cast on 64-bit
soc: aspeed: Adapt to new LPC device tree layout
pinctrl: aspeed-g5: Adapt to new LPC device tree layout
ipmi: kcs: aspeed: Adapt to new LPC DTS layout
ARM: dts: Remove LPC BMC and Host partitions
dt-bindings: aspeed-lpc: Remove LPC partitioning
soc: fsl: enable acpi support in RCPM driver
soc: qcom: mdt_loader: Detect truncated read of segments
soc: qcom: mdt_loader: Validate that p_filesz < p_memsz
soc: qcom: pdr: Fix error return code in pdr_register_listener
firmware: qcom_scm: Fix kernel-doc function names to match
firmware: qcom_scm: Suppress sysfs bind attributes
firmware: qcom_scm: Workaround lack of "is available" call on SC7180
firmware: qcom_scm: Reduce locking section for __get_convention()
firmware: qcom_scm: Make __qcom_scm_is_call_available() return bool
Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
...
Allow more drivers to be compile tested more easily, for example, when
doing subsystem-wide changes.
Verified on X86_64 as well as arm, powerpc and m68k with minimal configs
in order to catch missing implicit build dependencies (e.g. MAILBOX for
SERIAL_TEGRA_TCU).
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210422080211.29326-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the support for two optional DT properties, to configure RX and TX
FIFO thresholds:
- rx-threshold
- tx-threshold
This replaces hard-coded 8 bytes threshold. Keep 8 as the default value if
not specified, for backward compatibility.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Changes in v2:
Change added properties naming as proposed by Rob Herring.
Link: https://lore.kernel.org/r/20210413174015.23011-5-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c8dbdc842d ("serial: xuartps: Rewrite the interrupt handling
logic") reworked the driver interrupt processing but also, without
comment, added an unnecessary workaround for the infamous low_latency
behaviour of tty_flip_buffer_push() which had been removed years
before.
Specifically, since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-27-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit de49df5836 ("tty: serial: vt8500: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.
Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.
The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.
Since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.
Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Cc: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-26-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timbuart driver has always carried a workaround for the infamous
low_latency behaviour of tty_flip_buffer_push() which required not
holding the port lock when the low_latency flag was set.
Since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-25-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sunsu driver has been carrying a workaround for the infamous
low_latency behaviour of tty_flip_buffer_push() by dropping and
reacquiring the port lock in the interrupt handler since 2004.
Since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-24-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sifive driver has always carried an unnecessary workaround for the
infamous low_latency behaviour of tty_flip_buffer_push() which had been
removed years before the driver was added by commit 45c054d081 ("tty:
serial: add driver for the SiFive UART").
Specifically, since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-23-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f5ee56cc18 ("[PATCH] txx9 serial update") worked around the
infamous low_latency behaviour of tty_flip_buffer_push() by simply
dropping and reacquiring the port lock in the interrupt handler.
Since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-22-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 53e0e6706c ("tty: serial: sa1100: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.
Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.
The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.
Since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.
Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-21-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit de7053c771 ("tty: serial: rp2: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.
Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.
The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.
Since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.
Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Cc: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-20-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rda driver has always carried an unnecessary workaround for the
infamous low_latency behaviour of tty_flip_buffer_push(), which had
been removed years before the driver was added by commit c10b13325c
("tty: serial: Add RDA8810PL UART driver").
Specifically, since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-19-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The owl driver has always carried an unnecessary workaround for the
infamous low_latency behaviour of tty_flip_buffer_push(), which had
been removed years before the driver was added by commit fc60a8b675
("tty: serial: owl: Implement console driver").
Specifically, since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-18-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f77232dab2 ("tty: serial: msm: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.
Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.
The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.
Since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.
Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-17-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fbe543b412 ("Fix a potential issue in mpc52xx uart driver")
worked around the infamous low_latency behaviour of
tty_flip_buffer_push() by simply dropping and reacquiring the port lock
in the interrupt handler.
Since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-16-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The meson driver has always carried an unnecessary workaround for the
infamous low_latency behaviour of tty_flip_buffer_push(), which had
already been removed by the time the driver was added by commit
ff7693d079 ("ARM: meson: serial: add MesonX SoC on-chip uart driver").
Specifically, since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-15-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5275ad70fe ("tty: serial: mcf: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.
Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.
The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.
Since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.
Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-14-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ec12851090 ("tty: serial: lpc32xx_hs: drop uart_port->lock
before calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.
Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.
The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.
Since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.
Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-13-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5faf75d7fe ("tty: serial: icom: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.
Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.
The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.
Since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.
Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-12-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b4d499241c ("tty: serial: bcm63xx: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.
Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.
The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.
Since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.
Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-11-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1ecc26bd27 ("atmel_serial: split the interrupt handler") worked
around the infamous low_latency behaviour of tty_flip_buffer_push() by
dropping and reacquiring the port lock in the tasklet callback.
Since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.
Cc: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-10-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3fa1200851 ("tty: serial: arc: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.
Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.
The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.
Since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.
Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Cc: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-9-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b16c8e3eed ("tty: serial: ar933x: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.
Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.
The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.
Since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.
Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-8-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 78d34d75c8 ("tty: serial: apbuart: drop uart_port->lock before
calling tty_flip_buffer_push()") claimed to address a locking
issue but only provided a dubious lockdep splat from an unrelated
driver, which in the end turned out to be due a broken local change
carried by the author.
Unfortunately these patches were merged before the issue had been
analysed properly so the commit messages makes no sense whatsoever.
The real issue was first seen on RT which at the time effectively always
set the low_latency flag for all serial drivers by patching
tty_flip_buffer_push(). This in turn revealed that many drivers did not
handle the infamous low_latency behaviour which meant that data was
pushed immediately to the line discipline instead of being deferred to a
work queue.
Since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks
around.
Link: https://lore.kernel.org/linux-serial/cover.1376923198.git.viresh.kumar@linaro.org/
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-7-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ead76f329f ("ARM: 6763/1: pl011: add optional RX DMA to PL011
v2") added RX DMA support and also reproduced the workaround for the
infamous low_latency behaviour of tty_flip_buffer_push() by dropping and
reacquiring the port lock during receive processing.
Since commit a9c3f68f3c ("tty: Fix low_latency BUG"),
tty_flip_buffer_push() always schedules a work item to push data to the
line discipline and there's no need to keep any low_latency hacks around.
Note that the port lock is also dropped in the PIO path
(see pl011_rx_chars), but it is not clear whether this is still needed
by the DMA code added by the aforementioned commit.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@armlinux.org.uk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210421095509.3024-6-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
