This patch implements the backward compatibility with the old firmware where
the Tx completion IRQ interrupt was absent whereas incase of new firmware
the Tx completion IRQ interrupt is present.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements couple of fixes to support ACPI for RGMII/SGMII0/XFI
interface of APM X-Gene SoC ethernet controller driver. This patch uses
the _SUN acpi object to fetch the port-id information whereas the FDT uses
port-id binding for port-id information.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple LAN device for debug or management purposes.
Device supports interrupts for RX and TX(completion).
Device does not have DMA ability.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Tal Zilcer <talz@ezchip.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Below case causes mii bus probe failed:
ifconfig eth0 down -> suspend/resume with Mega/fax mix off -> ifconfig eth0 up
In i.MX6SX/i.MX7D chip, Mega/fast mix off feature is supported that means most of
SOC power will be off including ENET MAC for power saving. Once ENET MAC power
off, all initialized MAC registers reset to default, so in the case, it must
init MAC prior to mii bus probe.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While IEEE and CEE use the same structure to store apps, the selector
and priority fields for both are different. Only the priority field is
explained, add documentation explaining how the selector field differs
for both.
cgdcbxd code shows an example of how selector fields differ.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This particular BUG_ON condition was checking for attr set err in the
COMMIT phase, which isn't expected (it's a driver bug if PREPARE phase is
OK but COMMIT fails). But BUG_ON() is too strong for this case, so change
to WARN(). BUG_ON() would be warranted if the system was corrupted beyond
repair, but this is not the case here.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scott Feldman says:
====================
switchdev; add VLAN support for port's bridge_getlink
One more missing piece of the puzzle. Add vlan dump support to switchdev
port's bridge_getlink. iproute2 "bridge vlan show" cmd already knows how
to show the vlans installed on the bridge and the device , but (until now)
no one implemented the port vlan part of the netlink PF_BRIDGE:RTM_GETLINK
msg. Before this patch, "bridge vlan show":
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlans
57
sw1p1 << device side vlans (missing)
sw1p2 57
sw1p2
sw1p3
sw1p4
br0 None
(When the port is bridged, the output repeats the vlan list for the vlans
on the bridge side of the port and the vlans on the device side of the
port. The listing above show no vlans for the device side even though they
are installed).
After this patch:
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlan
57
sw1p1 30-34 << device side vlans
57
3840 PVID
sw1p2 57
sw1p2 57
3840 PVID
sw1p3 3842 PVID
sw1p4 3843 PVID
br0 None
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
One more missing piece of the puzzle. Add vlan dump support to switchdev
port's bridge_getlink. iproute2 "bridge vlan show" cmd already knows how
to show the vlans installed on the bridge and the device , but (until now)
no one implemented the port vlan part of the netlink PF_BRIDGE:RTM_GETLINK
msg. Before this patch, "bridge vlan show":
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlans
57
sw1p1 << device side vlans (missing)
sw1p2 57
sw1p2
sw1p3
sw1p4
br0 None
(When the port is bridged, the output repeats the vlan list for the vlans
on the bridge side of the port and the vlans on the device side of the
port. The listing above show no vlans for the device side even though they
are installed).
After this patch:
$ bridge -c vlan show
port vlan ids
sw1p1 30-34 << bridge side vlan
57
sw1p1 30-34 << device side vlans
57
3840 PVID
sw1p2 57
sw1p2 57
3840 PVID
sw1p3 3842 PVID
sw1p4 3843 PVID
br0 None
I re-used ndo_dflt_bridge_getlink to add vlan fill call-back func.
switchdev support adds an obj dump for VLAN objects, using the same
call-back scheme as FDB dump. Support included for both compressed and
un-compressed vlan dumps.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vid_begin/end to be consistent with BRIDGE_VLAN_INFO_RANGE_BEGIN/END.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove handling of tx_ring in prb_setup_retire_blk_timer
for TPACKET_V3 because init_prb_bdqc is called only for zero tx_ring
and thus prb_setup_retire_blk_timer for zero tx_ring only.
And also in functon init_prb_bdqc there is no usage of tx_ring.
Thus removing tx_ring from init_prb_bdqc.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Suggested-by: Frans Klaver <fransklaver@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiko Stuebner says:
====================
net: stmmac: dwmac-rk: add support for rk3368
Apart from small cleanups, this series provides support for the dwmac
on the new rk3368 ARM64 soc.
Tested on a R88 board using a RMII phy.
Changes since v1:
- Adapt to changes resulting from patch d42202dce0 ("net: stmmac:
dwmac-rk: Don't add function name in info or err messages")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add constants and callback functions for the dwmac on rk3368 socs.
As can be seen, the base structure is the same, only registers and
the bits in them moved slightly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac settings like RGMII/RMII, speeds etc are done in the so called
"General Register Files", contain numerous other settings as well and
always seem to change between Rockchip SoCs. Therefore abstract the
register accesses into a per-soc ops struct to make this reusable on
other Rockchip SoCs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first iteration of the dwmac-rk support did access an intermediate
clock directly below the pll selector. This was removed in a subsequent
revision, but the clock and one invocation remained. This results in
the driver trying to set the rate of a non-existent clock when the soc
and not some external source provides the phy clock for RMII phys.
So set the rate of the correct clock and remove the remaining now
completely unused definition.
Fixes: 436f5ae08f9d ("GMAC: add driver for Rockchip RK3288 SoCs integrated GMAC")
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a first version the driver did want to do some gpio wiggling, which
of course never made it into the kernel, but somehow these register
defines where forgotten. Remove them, as they shouldn't be here.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zero the statistics counters when setting up the global
registers. Otherwise the counters will remain from the last boot if
the power has not been removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the contents of the scratch registers to be shown in debugfs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device map is used to route packets between cascaded switches.
Add dumping a switches device map via debugfs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the contents of the statistics counters to be shown in debugfs.
This is particularly useful for the cpu and dsa ports, which cannot be
seen using ethtools -S.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code to retrieve a statistics counter into a function of its
own, so it can later be reused.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump the Address Translation Unit via a file in debugfs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the contents of the registers to be shown in debugfs.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the driver understand adapter version 2.
Cc: Rachel Lunnon <rachel_lunnon@stormagic.com>
Signed-off-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If rcd length was zero, the page used for frag was not being released. It
was being replaced with a newly allocated page. This change takes care
of that memory leak.
Signed-off-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a handler for pci shutdown so that the driver has an
opportunity to make sure that device is quiesced before the PCI
switches to legacy IRQs. This way the possibility of
"screaming interrupt" is avoided.
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currenlty nf_tables chains added in one network namespace are being
run in all network namespace. The issues are myriad with the simplest
being an unprivileged user can cause any network packets to be dropped.
Address this by simply not running nf_tables chains in the wrong
network namespace.
Cc: stable@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macvtap should be compatible with tuntap for
maximum number of queues.
commit 'baf71c5c1f80d82e92924050a60b5baaf97e3094 (tuntap:
Increase the number of queues in tun.)' removes
the limitations and increases number of queues in tuntap.
Now, Its safe to increase number of queues in Macvtap as well.
This patch also modifies 'macvtap_del_queues' function
to avoid extra memory allocation in stack.
Changes from v1->v2 :
Michael S. Tsirkin, Jason Wang :
Better way to use linked list to
avoid use of extra memory in stack.
Sergei Shtylyov : Specify dependent commit's summary.
Signed-off-by: Pankaj Gupta <pagupta@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When STP is running in user-space and querier is configured, the
querier timer is not started when a port goes to a non-blocking state.
This patch unifies the user- and kernel-space stp multicast port enable
path and enables it in all states different from blocking. Note that when a
port goes in BR_STATE_DISABLED it's not enabled because that is handled
in the beginning of the port list loop.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one only contains a one liner fix for a typo that I
introduced while cleaning some of the nfcmrvl patches that
were part of the 1st 4.2 pull request.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4H3o
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
NFC 4.2 2nd pull request
This one only contains a one liner fix for a typo that I
introduced while cleaning some of the nfcmrvl patches that
were part of the 1st 4.2 pull request.
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-06-18
Here's the final bluetooth-next pull request for 4.2.
- Cleanups & fixes to 802.15.4 code and related drivers
- Fix btusb driver memory leak
- New USB IDs for Atheros controllers
- Support for BCM4324B3 UART based Broadcom controller
- Fix for Bluetooth encryption key size handling
- Broadcom controller initialization fixes
- Support for Intel controller DDC parameters
- Support for multiple Bluetooth LE advertising instances
- Fix for HCI user channel cleanup path
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Actor and Partner details can be accessed via proc-fs, sys-fs
entries or netlink interface. These interfaces are world readable
at this moment. The earlier patch-series made the LACP communication
secure to avoid nuisance attack from within the same L2 domain but
it did not prevent "someone unprivileged" looking at that information
on host and perform the same act.
This patch essentially avoids spitting those entries if the user
in question does not have enough privileges.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Ferre says:
====================
net/macb: add sama5d2 support
This series is basically the support for another flavor of the GEM IP
configuration. It ended up being a series because of some little fixes made to
the binding documentation before adding the new compatibility string.
Bye,
v2: - fix bindings
- add sama5d2 compatibility string to the binding documentation
====================
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the compatible string for Atmel sama5d2 SoC family as the configuration
options differ from other instances of the GEM.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sama5d2 to the biding documentation for this use of the GEM IP.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On sama5d4, we only have a GEM IP that is configured to do 10/100 Mbits. So the
use of "Gigabit" can be confusing.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the driver and the DT bindings we use the "atmel" prefix. Fix it in the
binding documentation.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_diag_dump_reqs() is called from inet_diag_dump_icsk() with BH
disabled. So no need to disable BH in inet_diag_dump_reqs().
Signed-off-by: Hiroaki Shimoda <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8211F has different register definitions from RTL8211E.
Specially it needs to enable TXDLY in case of RGMII.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mwifiex:
* enhancements for AP mode: support verbose information in station
dump command and also information about AP link.
* enable power save by default
brcmfmac:
* fix module reload issue for PCIe
* improving msgbuf protocol for PCIe devices
* rework .get_station() cfg80211 callback operation
* determine interface combinations upon device feature support
ath9k:
* ath9k_htc: add support of channel switch
wil6210:
* add modparam for bcast ring size
* support hidden SSID
* add per-MCS Rx stats
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVglpWAAoJEG4XJFUm622bkT0H+QE/T3i44l6SEAxHEgW6Z2JP
MsAVHFV8q2jPCGfg4oCozk3fo2WPdBKwhUy7xzAg/LfxuTn0CtIzl+KuEnhsBBsx
+cNBFgBzIvHaMwfb/vxmuLK7zUROtDgOK7Kt4HF9p/Mn/JH8yTCrRy96hpnVKnuQ
h6HFO8Qx0l0pd6lbosaSPvjM8qBPy3ZfvriEHV3BTV+AXgSPWwnFkY188G2CNK5J
yYK0C2PkEX368m/qpmcbhlYrn3ZiJviiWhFmQZMW8eXe0k/pfBidXt6QGmKA7loT
p09skJk+qQtZjK4p2Hzy/3KOLU7YGFVHzww5gXqrZSxhluyhEdbOVLvKfB5jR68=
=3lke
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-06-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
mwifiex:
* enhancements for AP mode: support verbose information in station
dump command and also information about AP link.
* enable power save by default
brcmfmac:
* fix module reload issue for PCIe
* improving msgbuf protocol for PCIe devices
* rework .get_station() cfg80211 callback operation
* determine interface combinations upon device feature support
ath9k:
* ath9k_htc: add support of channel switch
wil6210:
* add modparam for bcast ring size
* support hidden SSID
* add per-MCS Rx stats
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the filter_dev check when dumping fdb entries, otherwise dump
returns empty list. filter_dev is always passed as NULL when dumping fdbs
on SELF. We want the fdbs installed on the device to be listed in the
dump.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Fixes: 45d4122c ("switchdev: add support for fdb add/del/dump via switchdev_port_obj ops")
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Vecera says:
====================
bna: clean-up 2
Next round of cleaning patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
BIT value is already unsigned so casting is not necessary.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds NLM_F_APPEND flag to struct nlmsg_hdr->nlmsg_flags
in newroute notifications if the route add was an append.
(This is similar to how NLM_F_REPLACE is already part of new
route replace notifications today)
This helps userspace determine if the route add operation was
an append.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds getsockopt(SOL_NETLINK, NETLINK_LIST_MEMBERSHIPS) to
retrieve all groups a socket is a member of. Currently, we have to use
getsockname() and look at the nl.nl_groups bitmask. However, this mask is
limited to 32 groups. Hence, similar to NETLINK_ADD_MEMBERSHIP and
NETLINK_DROP_MEMBERSHIP, this adds a separate sockopt to manager higher
groups IDs than 32.
This new NETLINK_LIST_MEMBERSHIPS option takes a pointer to __u32 and the
size of the array. The array is filled with the full membership-set of the
socket, and the required array size is returned in optlen. Hence,
user-space can retry with a properly sized array in case it was too small.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
