This reverts commit 53855d10f4.
It shouldn't have come in yet - it depends on the changes in linux-next
that will come in during the next merge window. As Matthew Wilcox says,
the test suite is broken with the current state without the revert.
Requested-by: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull parisc fixes from Helge Deller:
"Three important fixes for the parisc architecture.
Dave provided two patches: One which purges the TLB before setting a
PTE entry and a second one which drops unnecessary TLB flushes. Both
patches have been tested for one week on the debian buildd servers and
prevent random segmentation faults.
The patch from me fixes a crash at boot inside the TLB measuring code
on SMP machines with PA8000-PA8700 CPUs (specifically A500-44 and
J5000 servers)"
* 'parisc-4.9-5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix TLB related boot crash on SMP machines
parisc: Remove unnecessary TLB purges from flush_dcache_page_asm and flush_icache_page_asm
parisc: Purge TLB before setting PTE
At bootup we run measurements to calculate the best threshold for when we
should be using full TLB flushes instead of just flushing a specific amount of
TLB entries. This performance test is run over the kernel text segment.
But running this TLB performance test on the kernel text segment turned out to
crash some SMP machines when the kernel text pages were mapped as huge pages.
To avoid those crashes this patch simply skips this test on some SMP machines
and calculates an optimal threshold based on the maximum number of available
TLB entries and number of online CPUs.
On a technical side, this seems to happen:
The TLB measurement code uses flush_tlb_kernel_range() to flush specific TLB
entries with a page size of 4k (pdtlb 0(sr1,addr)). On UP systems this purge
instruction seems to work without problems even if the pages were mapped as
huge pages. But on SMP systems the TLB purge instruction is broadcasted to
other CPUs. Those CPUs then crash the machine because the page size is not as
expected. C8000 machines with PA8800/PA8900 CPUs were not affected by this
problem, because the required cache coherency prohibits to use huge pages at
all. Sadly I didn't found any documentation about this behaviour, so this
finding is purely based on testing with phyiscal SMP machines (A500-44 and
J5000, both were 2-way boxes).
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Helge Deller <deller@gmx.de>
One small fix for a regression in a prior fix (again). This time the
condition in the prior fix BUG_ON proved to be wrong under certain
circumstances causing a BUG to trigger where it shouldn't in the lpfc
driver.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=cyir
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"One small fix for a regression in a prior fix (again).
This time the condition in the prior fix BUG_ON proved to be wrong
under certain circumstances causing a BUG to trigger where it
shouldn't in the lpfc driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: fix oops/BUG in lpfc_sli_ringtxcmpl_put()
Merge more fixes from Andrew Morton:
"3 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
kcov: add missing #include <linux/sched.h>
radix tree test suite: fix compilation
zram: restrict add/remove attributes to root only
In __sanitizer_cov_trace_pc we use task_struct and fields within it, but
as we haven't included <linux/sched.h>, it is not guaranteed to be
defined. While we usually happen to acquire the definition through a
transitive include, this is fragile (and hasn't been true in the past,
causing issues with backports).
Include <linux/sched.h> to avoid any fragility.
[mark.rutland@arm.com: rewrote changelog]
Link: http://lkml.kernel.org/r/1481007384-27529-1-git-send-email-wangkefeng.wang@huawei.com
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch "lib/radix-tree: Convert to hotplug state machine" breaks the test
suite as it adds a call to cpuhp_setup_state_nocalls() which is not
currently emulated in the test suite. Add it, and delete the emulation
of the old CPU hotplug mechanism.
Link: http://lkml.kernel.org/r/1480369871-5271-36-git-send-email-mawilcox@linuxonhyperv.com
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Tested-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
zram hot_add sysfs attribute is a very 'special' attribute - reading
from it creates a new uninitialized zram device. This file, by a
mistake, can be read by a 'normal' user at the moment, while only root
must be able to create a new zram device, therefore hot_add attribute
must have S_IRUSR mode, not S_IRUGO.
[akpm@linux-foundation.org: s/sence/sense/, reflow comment to use 80 cols]
Fixes: 6566d1a32b ("zram: add dynamic device add/remove functionality")
Link: http://lkml.kernel.org/r/20161205155845.20129-1-sergey.senozhatsky@gmail.com
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Reported-by: Steven Allen <steven@stebalien.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: <stable@vger.kernel.org> [4.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 fixes from Ingo Molnar:
"Misc fixes: a core dumping crash fix, a guess-unwinder regression fix,
plus three build warning fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/unwind: Fix guess-unwinder regression
x86/build: Annotate die() with noreturn to fix build warning on clang
x86/platform/olpc: Fix resume handler build warning
x86/apic/uv: Silence a shift wrapping warning
x86/coredump: Always use user_regs_struct for compat_elf_gregset_t
Pull perf fixes from Ingo Molnar:
"A bogus warning fix, a counter width handling fix affecting certain
machines, plus a oneliner hw-enablement patch for Knights Mill CPUs"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Remove invalid warning from list_update_cgroup_even()t
perf/x86: Fix full width counter, counter overflow
perf/x86/intel: Enable C-state residency events for Knights Mill
Pull locking fixes from Ingo Molnar:
"Two rtmutex race fixes (which miraculously never triggered, that we
know of), plus two lockdep printk formatting regression fixes"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lockdep: Fix report formatting
locking/rtmutex: Use READ_ONCE() in rt_mutex_owner()
locking/rtmutex: Prevent dequeue vs. unlock race
locking/selftest: Fix output since KERN_CONT changes
Pull objtool fix from Ingo Molnar:
"A single late breaking fix for objtool"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix bytes check of lea's rex_prefix
Pull fuse fix from Miklos Szeredi:
"Fix a regression spotted by Jeff Layton"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix clearing suid, sgid for chown()
This reverts commit 8ab2ae655b.
I loved that commit because of how it explained what the problem with
newer versions of binutils were, but the actual patch itself turns out
to not work very well.
It has two problems:
- a zero CRC value isn't actually right. It happens to work for the
case where both sides of the equation fail at giving the symbol a
crc, but there are cases where the users of the exported symbol get
the right crc (due to seeing the C declarations), but the actual
exporting itself does not (due to the whole weak asm symbol issue).
So then the module load fails after all - we did have a crc for the
symbol, but we couldn't match it with the loaded module.
- it seems that the alpha assembler has special semantics for the
'.set' directive, and on alpha it doesn't actually set the value of
the specified symbol at all, it is instead used to set various
assembly modes (eg ".set noat" and ".set noreorder").
So using ".set" to set the symbol value would just cause build
failures on alpha.
I'm sure we'll find some other workaround for these issues (hopefully
that involves getting rid of modversions entirely some day, but people
are also talking about just using smarter tools). But for now we'll
just fall back on commit faaae2a581 ("Re-enable CONFIG_MODVERSIONS in
a slightly weaker form") that just let's a missing crc through.
Reported-by: Jan Stancek <jstancek@redhat.com>
Reported-by: Philip Müller <philm@manjaro.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In theory we could map other things, but there's a reason that function
is called "user_iov". Using anything else (like splice can do) just
confuses it.
Reported-and-tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have four routines in pacache.S that use temporary alias pages:
copy_user_page_asm(), clear_user_page_asm(), flush_dcache_page_asm() and
flush_icache_page_asm(). copy_user_page_asm() and clear_user_page_asm()
don't purge the TLB entry used for the operation.
flush_dcache_page_asm() and flush_icache_page_asm do purge the entry.
Presumably, this was thought to optimize TLB use. However, the
operation is quite heavy weight on PA 1.X processors as we need to take
the TLB lock and a TLB broadcast is sent to all processors.
This patch removes the purges from flush_dcache_page_asm() and
flush_icache_page_asm.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Helge Deller <deller@gmx.de>
The attached change interchanges the order of purging the TLB and
setting the corresponding page table entry. TLB purges are strongly
ordered. It occurred to me one night that setting the PTE first might
have subtle ordering issues on SMP machines and cause random memory
corruption.
A TLB lock guards the insertion of user TLB entries. So after the TLB
is purged, a new entry can't be inserted until the lock is released.
This ensures that the new PTE value is used when the lock is released.
Since making this change, no random segmentation faults have been
observed on the Debian hppa buildd servers.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Helge Deller <deller@gmx.de>
Pull sparc fix from David Miller:
"A use-before-NULL-check from Dan Carpenter"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
dbri: move dereference after check for NULL
We accidentally introduced a dereference before the NULL check in
xmit_descs() as part of silencing a GCC warning.
Fixes: 16f46050e7 ("dbri: Fix compiler warning")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) When dcbnl_cee_fill() fails to be able to push a new netlink
attribute, it return 0 instead of an error code. From Pan Bian.
2) Two suffix handling fixes to FIB trie code, from Alexander Duyck.
3) bnxt_hwrm_stat_ctx_alloc() goes through all the trouble of setting
and maintaining a return code 'rc' but fails to actually return it.
Also from Pan Bian.
4) ping socket ICMP handler needs to validate ICMP header length, from
Kees Cook.
5) caif_sktinit_module() has this interesting logic:
int err = sock_register(...);
if (!err)
return err;
return 0;
Just return sock_register()'s return value directly which is the
only possible correct thing to do.
6) Two bnx2x driver fixes from Yuval Mintz, return a reasonable
estimate from get_ringparam() ethtool op when interface is down and
avoid trying to use UDP port based tunneling on 577xx chips.
7) Fix ep93xx_eth crash on module unload from Florian Fainelli.
8) Missing uapi exports, from Stephen Hemminger.
9) Don't schedule work from sk_destruct(), because the socket will be
freed upon return from that function. From Herbert Xu.
10) Buggy drivers, of which we know there is at least one, can send a
huge packet into the TCP stack but forget to set the gso_size in the
SKB, which causes all kinds of problems.
Correct this when it happens, and emit a one-time warning with the
device name included so that it can be diagnosed more easily.
From Marcelo Ricardo Leitner.
11) virtio-net does DMA off the stack causes hiccups with VMAP_STACK,
fix from Andy Lutomirski.
12) Fix fec driver compilation with CONFIG_M5272, from Nikita
Yushchenko.
13) mlx5 fixes from Kamal Heib, Saeed Mahameed, and Mohamad Haj Yahia.
(erroneously flushing queues on error, module parameter validation,
etc)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
net/mlx5e: Change the SQ/RQ operational state to positive logic
net/mlx5e: Don't flush SQ on error
net/mlx5e: Don't notify HW when filling the edge of ICO SQ
net/mlx5: Fix query ISSI flow
net/mlx5: Remove duplicate pci dev name print
net/mlx5: Verify module parameters
net: fec: fix compile with CONFIG_M5272
be2net: Add DEVSEC privilege to SET_HSW_CONFIG command.
virtio-net: Fix DMA-from-the-stack in virtnet_set_mac_address()
tcp: warn on bogus MSS and try to amend it
uapi glibc compat: fix outer guard of net device flags enum
net: stmmac: clear reset value of snps, wr_osr_lmt/snps, rd_osr_lmt before writing
netlink: Do not schedule work from sk_destruct
uapi: export nf_log.h
uapi: export tc_skbmod.h
net: ep93xx_eth: Do not crash unloading module
bnx2x: Prevent tunnel config for 577xx
bnx2x: Correct ringparam estimate when DOWN
isdn: hisax: set error code on failure
net: bnx2x: fix improper return value
...
The shmem hole punching with fallocate(FALLOC_FL_PUNCH_HOLE) does not
want to race with generating new pages by faulting them in.
However, the wait-queue used to delay the page faulting has a serious
problem: the wait queue head (in shmem_fallocate()) is allocated on the
stack, and the code expects that "wake_up_all()" will make sure that all
the queue entries are gone before the stack frame is de-allocated.
And that is not at all necessarily the case.
Yes, a normal wake-up sequence will remove the wait-queue entry that
caused the wakeup (see "autoremove_wake_function()"), but the key
wording there is "that caused the wakeup". When there are multiple
possible wakeup sources, the wait queue entry may well stay around.
And _particularly_ in a page fault path, we may be faulting in new pages
from user space while we also have other things going on, and there may
well be other pending wakeups.
So despite the "wake_up_all()", it's not at all guaranteed that all list
entries are removed from the wait queue head on the stack.
Fix this by introducing a new wakeup function that removes the list
entry unconditionally, even if the target process had already woken up
for other reasons. Use that "synchronous" function to set up the
waiters in shmem_fault().
This problem has never been seen in the wild afaik, but Dave Jones has
reported it on and off while running trinity. We thought we fixed the
stack corruption with the blk-mq rq_list locking fix (commit
7fe311302f7d: "blk-mq: update hardware and software queues for sleeping
alloc"), but it turns out there was _another_ stack corruptor hiding
in the trinity runs.
Vegard Nossum (also running trinity) was able to trigger this one fairly
consistently, and made us look once again at the shmem code due to the
faults often being in that area.
Reported-and-tested-by: Vegard Nossum <vegard.nossum@oracle.com>.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Saeed Mahameed says:
====================
Mellanox 100G mlx5 fixes 2016-12-04
Some bug fixes for mlx5 core and mlx5e driver.
v1->v2:
- replace "uint" with "unsigned int"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the negative logic (i.e. FLUSH state), after the RQ/SQ reopen
we will have a time interval that the RQ/SQ is not really ready and the
state indicates that its not in FLUSH state because the initial SQ/RQ struct
memory starts as zeros.
Now we changed the state to indicate if the SQ/RQ is opened and we will
set the READY state after finishing preparing all the SQ/RQ resources.
Fixes: 6e8dd6d6f4 ("net/mlx5e: Don't wait for SQ completions on close")
Fixes: f2fde18c52 ("net/mlx5e: Don't wait for RQ completions on close")
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are doing SQ descriptors cleanup in driver.
Fixes: 6e8dd6d6f4 ("net/mlx5e: Don't wait for SQ completions on close")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to do this a couple of steps ahead anyway.
Fixes: d3c9bc2743 ("net/mlx5e: Added ICO SQs")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In old FWs query ISSI command is not supported and for some of those FWs
it might fail with status other than "MLX5_CMD_STAT_BAD_OP_ERR".
In such case instead of failing the driver load, we will treat any FW
status other than 0 for Query ISSI FW command as ISSI not supported and
assume ISSI=0 (most basic driver/FW interface).
In case of driver syndrom (query ISSI failure by driver) we will fail
driver load.
Fixes: f62b8bb8f2 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicate pci dev name printing from mlx5_core_warn/dbg.
Fixes: 5a7883989b ('net/mlx5_core: Improve mlx5 messages')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify the mlx5_core module parameters by making sure that they are in
the expected range and if they aren't restore them to their default
values.
Fixes: 9603b61de1 ('mlx5: Move pci device handling from mlx5_ib to mlx5_core')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 80cca775cd ("net: fec: cache statistics while device is down")
introduced unconditional statistics-related actions.
However, when driver is compiled with CONFIG_M5272, staticsics-related
definitions do not exist, which results into build errors.
Fix that by adding explicit handling of !defined(CONFIG_M5272) case.
Fixes: 80cca775cd ("net: fec: cache statistics while device is down")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OPCODE_COMMON_GET_FN_PRIVILEGES is returning only DEVSEC
privilege (Unrestricted Administrative Privilege) for Lancer NIC functions.
So, driver is failing SET_HSW_CONFIG command, as DEVSEC privilege was not
set in the privilege bitmap. This patch fixes the problem by setting DEVSEC
privilege in SET_HSW_CONFIG’s privilege bitmap.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_VMAP_STACK=y, virtnet_set_mac_address() can be passed a
pointer to the stack and it will OOPS. Copy the address to the heap
to prevent the crash.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Laura Abbott <labbott@redhat.com>
Reported-by: zbyszek@in.waw.pl
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been some reports lately about TCP connection stalls caused
by NIC drivers that aren't setting gso_size on aggregated packets on rx
path. This causes TCP to assume that the MSS is actually the size of the
aggregated packet, which is invalid.
Although the proper fix is to be done at each driver, it's often hard
and cumbersome for one to debug, come to such root cause and report/fix
it.
This patch amends this situation in two ways. First, it adds a warning
on when this situation occurs, so it gives a hint to those trying to
debug this. It also limit the maximum probed MSS to the adverised MSS,
as it should never be any higher than that.
The result is that the connection may not have the best performance ever
but it shouldn't stall, and the admin will have a hint on what to look
for.
Tested with virtio by forcing gso_size to 0.
v2: updated msg per David's suggestion
v3: use skb_iif to find the interface and also log its name, per Eric
Dumazet's suggestion. As the skb may be backlogged and the interface
gone by then, we need to check if the number still has a meaning.
v4: use helper tcp_gro_dev_warn() and avoid pr_warn_once inside __once, per
David's suggestion
Cc: Jonathan Maxwell <jmaxwell37@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a wrong condition preventing the higher net device flags
IFF_LOWER_UP etc to be defined if net/if.h is included before
linux/if.h.
The comment makes it clear the intention was to allow partial
definition with either parts.
This fixes compilation of userspace programs trying to use
IFF_LOWER_UP, IFF_DORMANT or IFF_ECHO.
Fixes: 4a91cb61bb ("uapi glibc compat: fix compile errors when glibc net/if.h included before linux/if.h")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
WR_OSR_LMT and RD_OSR_LMT have a reset value of 1.
Since the reset value wasn't cleared before writing, the value in the
register would be incorrect if specifying an uneven value for
snps,wr_osr_lmt/snps,rd_osr_lmt.
Zero is a valid value for the properties, since the databook specifies:
maximum outstanding requests = WR_OSR_LMT + 1.
We do not want to change the behavior for existing users when the
property is missing. Therefore, default to 1 if the property is missing,
since that is the same as the reset value.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basically, the pjdfstests set the ownership of a file to 06555, and then
chowns it (as root) to a new uid/gid. Prior to commit a09f99edde ("fuse:
fix killing s[ug]id in setattr"), fuse would send down a setattr with both
the uid/gid change and a new mode. Now, it just sends down the uid/gid
change.
Technically this is NOTABUG, since POSIX doesn't _require_ that we clear
these bits for a privileged process, but Linux (wisely) has done that and I
think we don't want to change that behavior here.
This is caused by the use of should_remove_suid(), which will always return
0 when the process has CAP_FSETID.
In fact we really don't need to be calling should_remove_suid() at all,
since we've already been indicated that we should remove the suid, we just
don't want to use a (very) stale mode for that.
This patch should fix the above as well as simplify the logic.
Reported-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: a09f99edde ("fuse: fix killing s[ug]id in setattr")
Cc: <stable@vger.kernel.org>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Since commit:
4bcc595ccd ("printk: reinstate KERN_CONT for printing continuation lines")
printk() requires KERN_CONT to continue log messages. Lots of printk()
in lockdep.c and print_ip_sym() don't have it. As the result lockdep
reports are completely messed up.
Add missing KERN_CONT and inline print_ip_sym() where necessary.
Example of a messed up report:
0-rc5+ #41 Not tainted
-------------------------------------------------------
syz-executor0/5036 is trying to acquire lock:
(
rtnl_mutex
){+.+.+.}
, at:
[<ffffffff86b3d6ac>] rtnl_lock+0x1c/0x20
but task is already holding lock:
(
&net->packet.sklist_lock
){+.+...}
, at:
[<ffffffff873541a6>] packet_diag_dump+0x1a6/0x1920
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3
(
&net->packet.sklist_lock
+.+...}
...
Without this patch all scripts that parse kernel bug reports are broken.
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: andreyknvl@google.com
Cc: aryabinin@virtuozzo.com
Cc: joe@perches.com
Cc: syzkaller@googlegroups.com
Link: http://lkml.kernel.org/r/1480343083-48731-1-git-send-email-dvyukov@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The warning introduced in commit:
864c2357ca ("perf/core: Do not set cpuctx->cgrp for unscheduled cgroups")
assumed that a cgroup switch always precedes list_del_event. This is
not the case. Remove warning.
Make sure that cpuctx->cgrp is NULL until a cgroup event is sched in
or ctx->nr_cgroups == 0.
Signed-off-by: David Carrillo-Cisneros <davidcc@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi V Shankar <ravi.v.shankar@intel.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Vikas Shivappa <vikas.shivappa@linux.intel.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1480841177-27299-1-git-send-email-davidcc@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Lukasz reported that perf stat counters overflow handling is broken on KNL/SLM.
Both these parts have full_width_write set, and that does indeed have
a problem. In order to deal with counter wrap, we must sample the
counter at at least half the counter period (see also the sampling
theorem) such that we can unambiguously reconstruct the count.
However commit:
069e0c3c40 ("perf/x86/intel: Support full width counting")
sets the sampling interval to the full period, not half.
Fixing that exposes another issue, in that we must not sign extend the
delta value when we shift it right; the counter cannot have
decremented after all.
With both these issues fixed, counter overflow functions correctly
again.
Reported-by: Lukasz Odzioba <lukasz.odzioba@intel.com>
Tested-by: Liang, Kan <kan.liang@intel.com>
Tested-by: Odzioba, Lukasz <lukasz.odzioba@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: stable@vger.kernel.org
Fixes: 069e0c3c40 ("perf/x86/intel: Support full width counting")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Knights Mill is enough close to Knights Landing so the path reuses
C-state residency support of the latter.
Signed-off-by: Piotr Luc <piotr.luc@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/20161201000853.18260-1-piotr.luc@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For the "lea %(rsp), %rbp" case, we check if there is a rex_prefix.
But we check 'bytes' which is insn_byte_t[4] in rex_prefix (insn_field
structure). Therefore, the check is always true.
Instead, check 'nbytes' which is the right one.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20161205105551.25917-1-jslaby@suse.cz
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It is wrong to schedule a work from sk_destruct using the socket
as the memory reserve because the socket will be freed immediately
after the return from sk_destruct.
Instead we should do the deferral prior to sk_free.
This patch does just that.
Fixes: 707693c8a4 ("netlink: Call cb->done from a worker thread")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
File is in uapi directory but not being copied on
make install_headers
Fixes commit 4ec9c8fbbc22 ("netfilter: nft_log: complete
NFTA_LOG_FLAGS attr support").
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes commit 735cffe5d800 ("net_sched: Introduce skbmod action")
Not used by iproute2 but maybe in future.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we unload the ep93xx_eth, whether we have opened the network
interface or not, we will either hit a kernel paging request error, or a
simple NULL pointer de-reference because:
- if ep93xx_open has been called, we have created a valid DMA mapping
for ep->descs, when we call ep93xx_stop, we also call
ep93xx_free_buffers, ep->descs now has a stale value
- if ep93xx_open has not been called, we have a NULL pointer for
ep->descs, so performing any operation against that address just won't
work
Fix this by adding a NULL pointer check for ep->descs which means that
ep93xx_free_buffers() was able to successfully tear down the descriptors
and free the DMA cookie as well.
Fixes: 1d22e05df8 ("[PATCH] Cirrus Logic ep93xx ethernet driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yuval Mintz says:
====================
bnx2x: fixes series
Two unrelated fixes for bnx2x - the first one is nice-to-have,
while the other fixes fatal behaviour in older adapters.
Please consider applying them to `net'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the 578xx adapters are capable of configuring UDP ports for
the purpose of tunnelling - doing the same on 577xx might lead to
a firmware assertion.
We're already not claiming support for any related feature for such
devices, but we also need to prevent the configuration of the UDP
ports to the device in this case.
Fixes: f34fa14cc0 ("bnx2x: Add vxlan RSS support")
Reported-by: Anikina Anna <anikina@gmail.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until interface is up [and assuming ringparams weren't explicitly
configured] when queried for the size of its rings bnx2x would
claim they're the maximal size by default.
That is incorrect as by default the maximal number of buffers would
be equally divided between the various rx rings.
This prevents the user from actually setting the number of elements
on each rx ring to be of maximal size prior to transitioning the
interface into up state.
To fix this, make a rough estimation about the number of buffers.
It wouldn't always be accurate, but it would be much better than
current estimation and would allow users to increase number of
buffers during early initialization of the interface.
Reported-by: Seymour, Shane <shane.seymour@hpe.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function hfc4s8s_probe(), the value of return variable err should be
negative on failures. However, when the call to request_region() returns
NULL, the value of err is 0. This patch fixes the bug, assigning
"-EBUSY" to err on the path that request_region() fails.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188931
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macro BNX2X_ALLOC_AND_SET(arr, lbl, func) calls kmalloc() to allocate
memory, and jumps to label "lbl" if the allocation fails. Label "lbl"
first cleans memory and then returns variable rc. Before calling the
macro, the value of variable rc is 0. Because 0 means no error, the
callers of bnx2x_init_firmware() may be misled. This patch fixes the bug,
assigning "-ENOMEM" to rc before calling macro NX2X_ALLOC_AND_SET().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189141
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
