Add support for probing the pwm-jz4740 directly from devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This permits clients of this driver to specify the polarity to use for
their PWM channel.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
On the JZ4750 and later SoCs, channel 1 and 2 operate in a different
way (TCU2 mode) as the other channels. If a TCU2 mode counter is
stopped before its PWM functionality is disabled, the output is not
guaranteed to return to the initial level.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Now that the JZ4740 and similar SoCs have a pinctrl driver, we rely on
the pins being properly configured before the driver probes.
One inherent problem of this new approach is that the pinctrl framework
does not allow us to configure each pin on demand, when the various PWM
channels are requested or released. For instance, the PWM channels can
be configured from sysfs, which would require all PWM pins to be configured
properly beforehand for the PWM function, eventually causing conflicts
with other platform or board drivers.
The proper solution here would be to modify the pwm-jz4740 driver to
handle only one PWM channel, and create an instance of this driver
for each one of the 8 PWM channels. Then, it could use the pinctrl
framework to dynamically configure the PWM pin it controls.
Until this can be done, the only jz4740 board supported upstream
(Qi lb60) can configure all of its connected PWM pins in PWM function
mode, since those are not used by other drivers nor by GPIOs on the
board.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using the managed version of clk_get() makes the code a bit shorter and the
error paths less complicated.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
In preparation to switching the jz4740 clk driver to the common clk framework
make sure to pass the device to clk_get().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit moves the driver to drivers/pwm and converts it to the new
PWM framework.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
