Steven Noonan reported a boot hang when using irqpoll and
CONFIG_HAVE_SPARSE_IRQ=y.
The irqpoll loop needs to be updated to not iterate from 1 to nr_irqs
but to iterate via for_each_irq_desc(). (in the former case desc can
be NULL which crashes the box)
Reported-by: Steven Noonan <steven@uplinklabs.net>
Tested-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Change the IRQ affinity in the process context when the IRQ is disabled.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Extraneous call to irq_to_desc().
Signed-off-by: Dean Nelson <dcn@sgi.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Suresh Siddha noticed that we should have a spinlock around it.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This has been deprecated for years, the user space irqbalanced utility
works better with numa, has configurable policies, etc...
Signed-off-by: Yinghai Lu <yhlu.kernel@gmai.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
change names:
irq_desc() ==> irq_desc_alloc
__irq_desc() ==> irq_desc
Also split a few of the uses in lowlevel x86 code.
v2: need to check if desc is null in smp_irq_move_cleanup
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
So we could remove some duplicated calling to irq_desc
v2: make sure irq_desc in init/main.c is not used without generic_hardirqs
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
remove irq limit checks - nr_irqs is dynamic and we expand anytime.
v2: fix checking about result irq_cfg_without_new, so could use msi again
v3: use irq_desc_without_new to check irq is valid
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are a handful of loops that go from 0 to nr_irqs and use
get_irq_desc() on them. These would allocate all the irq_desc
entries, regardless of the need for them.
Use the smarter for_each_irq_desc() iterator that will only iterate
over the present ones.
v2: make sure arch without GENERIC_HARDIRQS work too
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
add an irq_desc accessor that will not allocate any sparse entry
but returns failure if there's no entry present.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
based on Eric's patch ...
together mold it with dyn_array for irq_desc, will allcate kstat_irqs for
nr_irq_desc alltogether if needed. -- at that point nr_cpus is known already.
v2: make sure system without generic_hardirqs works they don't have irq_desc
v3: fix merging
v4: [mingo@elte.hu] fix typo
[ mingo@elte.hu ] irq: build fix
fix:
arch/x86/xen/spinlock.c: In function 'xen_spin_lock_slow':
arch/x86/xen/spinlock.c:90: error: 'struct kernel_stat' has no member named 'irqs'
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
add CONFIG_HAVE_SPARSE_IRQ to for use condensed array.
Get rid of irq_desc[] array assumptions.
Preallocate 32 irq_desc, and irq_desc() will try to get more.
( No change in functionality is expected anywhere, except the odd build
failure where we missed a code site or where a crossing commit itroduces
new irq_desc[] usage. )
v2: according to Eric, change get_irq_desc() to irq_desc()
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
at this point nr_irqs is equal NR_IRQS
convert a few easy users from NR_IRQS to dynamic nr_irqs.
v2: according to Eric, we need to take care of arch without generic_hardirqs
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Genirq hasn't previously recorded the trigger type used by any given IRQ,
although some irq_chip support has done so. That data can be useful when
troubleshooting. This patch records it in the relevant irq_desc.status
bits, and improves consistency between the two driver-visible calls
affected:
- Make set_irq_type() usage match request_irq() usage:
* IRQ_TYPE_NONE should be a NOP; succeed, so irq_chip methods
won't have to handle that case any more (many do it wrong).
* IRQ_TYPE_PROBE is ignored; any buggy out-of-tree callers
might need to switch over to the real IRQ probing code.
* emit the same diagnostics (from shared utility code)
- Their kerneldoc now reflects usage:
* request_irq() flags include IRQF_TRIGGER_* to specify
active edge(s)/level ... docs previously omitted that
* set_irq_type() is declared in <linux/irq.h> so callers
should use the (bit-equivalent) IRQ_TYPE_* symbols there
Also: adds a warning about shared IRQs that don't end up using the
requested trigger mode; and fix an unrelated "sparse" warning.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch clarifies usage of irq_chip->startup() callback:
1. The "if (startup) startup(); else enabled();" code in setup_irq()
is unnecessary, as startup() falls back to enabled() via
default callbacks, set by irq_chip_set_defaults().
2. When using set_irq_chained_handler() the startup() was never called,
which is not good at all... Fixed. And again - when startup() is not
defined the call will fall back to enable() than to unmask() via
default callbacks.
Signed-off-by: Pawel Moll <pawel.moll@st.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When DEBUG_SHIRQ is selected, a spurious IRQ is issued before
the setup_irq() initializes the desc->depth. An IRQ handler may
call disable_irq_nosync(), but then setup_irq() will overwrite
desc->depth, and upon enable_irq() we'll catch this WARN:
------------[ cut here ]------------
Badness at kernel/irq/manage.c:180
NIP: c0061ab8 LR: c0061f10 CTR: 00000000
REGS: cf83be50 TRAP: 0700 Not tainted (2.6.27-rc3-23450-g74919b0)
MSR: 00021032 <ME,IR,DR> CR: 22042022 XER: 20000000
TASK = cf829100[5] 'events/0' THREAD: cf83a000
GPR00: c0061f10 cf83bf00 cf829100 c038e674 00000016 00000000 cf83bef8 00000038
GPR08: c0298910 00000000 c0310d28 cf83a000 00000c9c 1001a1a8 0fffe000 00800000
GPR16: ffffffff 00000000 007fff00 00000000 007ffeb0 c03320a0 c031095c c0310924
GPR24: cf8292ec cf807190 cf83a000 00009032 c038e6a4 c038e674 cf99b1cc c038e674
NIP [c0061ab8] __enable_irq+0x20/0x80
LR [c0061f10] enable_irq+0x50/0x70
Call Trace:
[cf83bf00] [c038e674] irq_desc+0x630/0x9000 (unreliable)
[cf83bf10] [c0061f10] enable_irq+0x50/0x70
[cf83bf30] [c01abe94] phy_change+0x68/0x108
[cf83bf50] [c0046394] run_workqueue+0xc4/0x16c
[cf83bf90] [c0046834] worker_thread+0x74/0xd4
[cf83bfd0] [c004ab7c] kthread+0x48/0x84
[cf83bff0] [c00135e0] kernel_thread+0x44/0x60
Instruction dump:
4e800020 3d20c031 38a94214 4bffffcc 9421fff0 7c0802a6 93e1000c 7c7f1b78
90010014 8123001c 2f890000 409e001c <0fe00000> 80010014 83e1000c 38210010
That trace corresponds to this line:
WARN(1, KERN_WARNING "Unbalanced enable for IRQ %d\n", irq);
The patch fixes the problem by moving the SHIRQ code below the
setup_irq().
Unfortunately we can't easily move the SHIRQ code inside the
setup_irq(), since it grabs a spinlock, so to prvent a 'real'
IRQ from interfere us we should disable that IRQ.
p.s. The driver in question is drivers/net/phy/phy.c.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Switch /proc/irq/*/smp_affinity , /proc/irq/default_smp_affinity to
seq_files.
cat(1) reads with 1024 chunks by default, with high enough NR_CPUS, there
will be -EINVAL.
As side effect, there are now two less users of the ->read_proc interface.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Paul Jackson <pj@sgi.com>
Cc: Mike Travis <travis@sgi.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While I'm glad to finally see the hole fixed whereby passing an invalid
IRQ trigger type to request_irq() would be ignored, the current diagnostic
isn't quite useful. Fixed by also listing the trigger type which was
rejected.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use WARN() instead of a printk+WARN_ON() pair; this way the message
becomes part of the warning section for better reporting/collection.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace a printk+WARN_ON() by a WARN(); this increases the chance of the
string making it into the bugreport (ie: it goes inside the
---[ cut here ]--- section)
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace a printk+WARN_ON() by a WARN(); this increases the chance of the
string making it into the bugreport (ie: it goes inside the
---[ cut here ]--- section)
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
set_type returns an int indicating success or failure, but up to now
setup_irq ignores that.
In my case this resulted in a machine hang:
gpio-keys requested IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING, but
arm/ns9xxx can only trigger on one direction so set_type didn't touch
the configuration which happens do default to a level sensitiveness and
returned -EINVAL. setup_irq ignored that and unmasked the irq. This
resulted in an endless triggering of the gpio-key interrupt service
routine which effectively killed the machine.
With this patch applied setup_irq propagates the error to the caller.
Note that before in the case
chip && !chip->set_type && !chip->name
a NULL pointer was feed to printk. This is fixed, too.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since 15a647eba9 set_irq_wake returned -ENXIO
if another device had it already enabled. Zero is the right value to
return in this case. Moreover the change to desc->status was not reverted
if desc->chip->set_wake returned an error.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we disable a screaming irq we never see it again. If the irq
line is shared or if the driver half works this is a real pain. So
periodically poll the handlers for screaming interrupts.
I use a timer instead of the classic irq poll technique of working off
the timer interrupt because when we use the local apic timers
note_interrupt is never called (bug?). Further on a system with
dynamic ticks the timer interrupt might not even fire unless there is
a timer telling it it needs to.
I forced this case on my test system with an e1000 nic and my ssh
session remained responsive despite the interrupt handler only being
called every 10th of a second.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In http://bugzilla.kernel.org/show_bug.cgi?id=9580 it was pointed out
that the desc->chip checks are extraneous. In fact these are left
overs from early development and can be removed safely.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Current IRQ affinity interface does not provide a way to set affinity
for the IRQs that will be allocated/activated in the future.
This patch creates /proc/irq/default_smp_affinity that lets users set
default affinity mask for the newly allocated IRQs. Changing the default
does not affect affinity masks for the currently active IRQs, they
have to be changed explicitly.
Updated based on Paul J's comments and added some more documentation.
Signed-off-by: Max Krasnyansky <maxk@qualcomm.com>
Cc: pj@sgi.com
Cc: a.p.zijlstra@chello.nl
Cc: tglx@linutronix.de
Cc: rdunlap@xenotime.net
Cc: mingo@elte.hu
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Uwe Kleine-Koenig has some strange hardware where one of the shared
interrupts can be asserted during boot before the appropriate driver
loads. Requesting the shared irq line from another driver result in a
spurious interrupt storm which finally disables the interrupt line.
I have seen similar behaviour on resume before (the hardware does not
work anymore so I can not verify).
Change the spurious disable logic to increment the disable depth and
mark the interrupt with an extra flag which allows us to reenable the
interrupt when a new driver arrives which requests the same irq
line. In the worst case this will disable the irq again via the
spurious trap, but there is a decent chance that the new driver is the
one which can handle the already asserted interrupt and makes the box
usable again.
Eric Biederman said further: This case also happens on a regular basis
in kdump kernels where we deliberately don't shutdown the hardware
before starting the new kernel. This patch should reduce the need for
using irqpoll in that situation by a small amount.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-and-Acked-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Following an experimental deletion of the unnecessary directive
#include <linux/slab.h>
from the header file <linux/percpu.h>, these files under kernel/ were exposed
as needing to include one of <linux/slab.h> or <linux/gfp.h>, so explicit
includes were added where necessary.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Replace usages of CPU_MASK_NONE, CPU_MASK_ALL, NODE_MASK_NONE,
NODE_MASK_ALL to reduce stack requirements for large NR_CPUS
and MAXNODES counts.
* In some cases, the cpumask variable was initialized but then overwritten
with another value. This is the case for changes like this:
- cpumask_t oldmask = CPU_MASK_ALL;
+ cpumask_t oldmask;
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The default_disable() function was changed in commit:
76d2160147
genirq: do not mask interrupts by default
It removed the mask function in favour of the default delayed
interrupt disabling. Unfortunately this also broke the shutdown in
free_irq() when the last handler is removed from the interrupt for
those architectures which rely on the default implementations. Now we
can end up with a enabled interrupt line after the last handler was
removed, which can result in spurious interrupts.
Fix this by adding a default_shutdown function, which is only
installed, when the irqchip implementation does provide neither a
shutdown nor a disable function.
[@stable: affected versions: .21 - .24 ]
Pointed-out-by: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: stable@kernel.org
Tested-by: Michael Hennerich <Michael.Hennerich@analog.com>
The functions time_before, time_before_eq, time_after, and
time_after_eq are more robust for comparing jiffies against other
values.
So following patch implements usage of the time_after() macro, defined
at linux/jiffies.h, which deals with wrapping correctly
Signed-off-by: S.Caglar Onur <caglar@pardus.org.tr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Probing non-ISA interrupts using the handle_percpu_irq as their handle_irq
method may crash the system because handle_percpu_irq does not check
IRQ_WAITING. This for example hits the MIPS Qemu configuration.
This patch provides two helper functions set_irq_noprobe and set_irq_probe to
set rsp. clear the IRQ_NOPROBE flag. The only current caller is MIPS code
but this really belongs into generic code.
As an aside, interrupt probing these days has become a mostly obsolete if not
dangerous art. I think Linux interrupts should be changed to default to
non-probing but that's subject of this patch.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-and-tested-by: Rob Landley <rob@landley.net>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
