The audio related clock support is missing from the existing zx296718
clock driver. Let's add it, so that the upstream ZX SPDIF driver can
work for HDMI audio support.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[sboyd@codeaurora.org: Staticize some more structures]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
It adds the compatible string for zx296718 audio clock controller.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Instead of using panic, we should give an error message and return error
code when of_clk_add_hw_provider() call fails.
Since we have error prompt for failures, the "init over" pr_info output
isn't really necessary but becomes a debug noise. So let's clean it up
along the way.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The delay here is not in atomic context and does not seem critical with
respect to precision, but usleep_range(min,max) with min==max results in
giving the timer subsystem no room to optimize uncritical delays. Fix
this by setting the range to 2000,3000 us.
Fixes: commit f05259a6ff ("clk: wm831x: Add initial WM831x clock driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
On vf610, PLL1 and PLL2 have registers to configure fractional part of
frequency multiplier.
This patch adds support for these registers.
This fixes "fast system clock" issue on boards where bootloader sets
fractional multiplier for PLL1.
Suggested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
CC: Chris Healy <cphealy@gmail.com>
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Tested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When we used to defer setting the "grf" member to
rockchip_clk_get_grf() it was important to init the "grf" member to an
error value in rockchip_clk_init(). With recent changes, we now set
"grf" right in rockchip_clk_init() (two lines below the place where we
initted it). That makes the old init useless. Get rid of it.
Fixes: 6f339dc271 ("clk: rockchip: lookup General Register Files in rockchip_clk_init")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the clock tree definition for the new rk3328 SoC.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add devicetree bindings for Rockchip cru which found on
Rockchip SoCs.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the dt-bindings header for the rk3328, that gets shared between
the clock controller and the clock references in the dts.
Add softreset ID for rk3328.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rk3328's pll and clock are similar with rk3036's,
it different with pll_mode_mask, the rk3328 soc
pll mode only one bit(rk3036 soc have two bits)
so these should be independent and separate from
the series of rk3328s.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With the newly introduced clk type for muxes in the grf we now can
describe some missing clocks, like the aclk_vcodec that selects between
aclk_vdpu and aclk_vepu based on a bit set in the general register files.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rockchip socs often have some tiny number of muxes not controlled from
the core clock controller but through bits set in the general register
files. Add a clock-type that can control these as well, so that we
don't need to work around them being absent.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull DAX updates from Dan Williams:
"The completion of Jan's DAX work for 4.10.
As I mentioned in the libnvdimm-for-4.10 pull request, these are some
final fixes for the DAX dirty-cacheline-tracking invalidation work
that was merged through the -mm, ext4, and xfs trees in -rc1. These
patches were prepared prior to the merge window, but we waited for
4.10-rc1 to have a stable merge base after all the prerequisites were
merged.
Quoting Jan on the overall changes in these patches:
"So I'd like all these 6 patches to go for rc2. The first three
patches fix invalidation of exceptional DAX entries (a bug which
is there for a long time) - without these patches data loss can
occur on power failure even though user called fsync(2). The other
three patches change locking of DAX faults so that ->iomap_begin()
is called in a more relaxed locking context and we are safe to
start a transaction there for ext4"
These have received a build success notification from the kbuild
robot, and pass the latest libnvdimm unit tests. There have not been
any -next releases since -rc1, so they have not appeared there"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
ext4: Simplify DAX fault path
dax: Call ->iomap_begin without entry lock during dax fault
dax: Finish fault completely when loading holes
dax: Avoid page invalidation races and unnecessary radix tree traversals
mm: Invalidate DAX radix tree entries only if appropriate
ext2: Return BH_New buffers for zeroed blocks
- A merge error on my part broke the DocBook build. I've requisitioned
one of tglx's frozen sharks for appropriate disciplinary action and
resolved to be more careful about testing the DocBook stuff as long as
it's still around.
- Fix an error in unaligned-memory-access.txt
-----BEGIN PGP SIGNATURE-----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=W4e5
-----END PGP SIGNATURE-----
Merge tag 'docs-4.10-rc1-fix' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"Two small fixes:
- A merge error on my part broke the DocBook build. I've
requisitioned one of tglx's frozen sharks for appropriate
disciplinary action and resolved to be more careful about testing
the DocBook stuff as long as it's still around.
- Fix an error in unaligned-memory-access.txt"
* tag 'docs-4.10-rc1-fix' of git://git.lwn.net/linux:
Documentation/unaligned-memory-access.txt: fix incorrect comparison operator
docs: Fix build failure
Pull crypto fix from Herbert Xu:
"This fixes a boot failure on some platforms when crypto self test is
enabled along with the new acomp interface"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: testmgr - Use heap buffer for acomp test input
mm/filemap.c: In function 'clear_bit_unlock_is_negative_byte':
mm/filemap.c:933:9: error: too few arguments to function 'test_bit'
return test_bit(PG_waiters);
^~~~~~~~
Fixes: b91e1302ad ('mm: optimize PageWaiters bit use for unlock_page()')
Signed-off-by: Olof Johansson <olof@lixom.net>
Brown-paper-bag-by: Linus Torvalds <dummy@duh.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit 6290602709 ("mm: add PageWaiters indicating tasks are
waiting for a page bit") Nick Piggin made our page locking no longer
unconditionally touch the hashed page waitqueue, which not only helps
performance in general, but is particularly helpful on NUMA machines
where the hashed wait queues can bounce around a lot.
However, the "clear lock bit atomically and then test the waiters bit"
sequence turns out to be much more expensive than it needs to be,
because you get a nasty stall when trying to access the same word that
just got updated atomically.
On architectures where locking is done with LL/SC, this would be trivial
to fix with a new primitive that clears one bit and tests another
atomically, but that ends up not working on x86, where the only atomic
operations that return the result end up being cmpxchg and xadd. The
atomic bit operations return the old value of the same bit we changed,
not the value of an unrelated bit.
On x86, we could put the lock bit in the high bit of the byte, and use
"xadd" with that bit (where the overflow ends up not touching other
bits), and look at the other bits of the result. However, an even
simpler model is to just use a regular atomic "and" to clear the lock
bit, and then the sign bit in eflags will indicate the resulting state
of the unrelated bit #7.
So by moving the PageWaiters bit up to bit #7, we can atomically clear
the lock bit and test the waiters bit on x86 too. And architectures
with LL/SC (which is all the usual RISC suspects), the particular bit
doesn't matter, so they are fine with this approach too.
This avoids the extra access to the same atomic word, and thus avoids
the costly stall at page unlock time.
The only downside is that the interface ends up being a bit odd and
specialized: clear a bit in a byte, and test the sign bit. Nick doesn't
love the resulting name of the new primitive, but I'd rather make the
name be descriptive and very clear about the limitation imposed by
trying to work across all relevant architectures than make it be some
generic thing that doesn't make the odd semantics explicit.
So this introduces the new architecture primitive
clear_bit_unlock_is_negative_byte();
and adds the trivial implementation for x86. We have a generic
non-optimized fallback (that just does a "clear_bit()"+"test_bit(7)"
combination) which can be overridden by any architecture that can do
better. According to Nick, Power has the same hickup x86 has, for
example, but some other architectures may not even care.
All these optimizations mean that my page locking stress-test (which is
just executing a lot of small short-lived shell scripts: "make test" in
the git source tree) no longer makes our page locking look horribly bad.
Before all these optimizations, just the unlock_page() costs were just
over 3% of all CPU overhead on "make test". After this, it's down to
0.66%, so just a quarter of the cost it used to be.
(The difference on NUMA is bigger, but there this micro-optimization is
likely less noticeable, since the big issue on NUMA was not the accesses
to 'struct page', but the waitqueue accesses that were already removed
by Nick's earlier commit).
Acked-by: Nick Piggin <npiggin@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Exynos AUDSS clock driver has been already converted to platform driver,
so remove the dependency on the syscore ops - the last remaining
non-platform driver feature. Platform device's system sleep PM provides
all needed infrastructure for replacing syscore-based PM, so do it now.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The ACLK_BUS0/1/2 are used for NoC (Network on Chip). If NoC's clocks are
disabled, the system halt happens. Following clocks must be always enabled:
- CLK_ACLK_BUS0_400 : NoC's bus clock for PERIC/PERIS/FSYS/MSCL,
- CLK_ACLK_BUS1_400 : NoC's bus clock for MFC/HEVC/G3D,
- CLK_ACLK_BUS2_400 : NoC's bus clock for GSCL/DISP/G2D/CAM0/CAM1/ISP.
This patch also adds the CLK_SET_RATE_PARENT flag to the CLK_SCLK_JPEG_MSCL
because this clock should be used for bus frequency scaling. This clock need
to be changed on the fly with CLK_SET_RATE_PARENT flag.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Add cpu clock configuration data for Exynos4412 Prime SoC
(it supports additional PLL rates & CPU frequencies).
Based on Hardkernel's kernel for ODROID-X2/U2/U3 boards.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Pull crypto fix from Herbert Xu:
"This fixes a hash corruption bug in the marvell driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: marvell - Copy IVDIG before launching partial DMA ahash requests
Pull networking fixes from David Miller:
1) Various ipvlan fixes from Eric Dumazet and Mahesh Bandewar.
The most important is to not assume the packet is RX just because
the destination address matches that of the device. Such an
assumption causes problems when an interface is put into loopback
mode.
2) If we retry when creating a new tc entry (because we dropped the
RTNL mutex in order to load a module, for example) we end up with
-EAGAIN and then loop trying to replay the request. But we didn't
reset some state when looping back to the top like this, and if
another thread meanwhile inserted the same tc entry we were trying
to, we re-link it creating an enless loop in the tc chain. Fix from
Daniel Borkmann.
3) There are two different WRITE bits in the MDIO address register for
the stmmac chip, depending upon the chip variant. Due to a bug we
could set them both, fix from Hock Leong Kweh.
4) Fix mlx4 bug in XDP_TX handling, from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: stmmac: fix incorrect bit set in gmac4 mdio addr register
r8169: add support for RTL8168 series add-on card.
net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
openvswitch: upcall: Fix vlan handling.
ipv4: Namespaceify tcp_tw_reuse knob
net: korina: Fix NAPI versus resources freeing
net, sched: fix soft lockup in tc_classify
net/mlx4_en: Fix user prio field in XDP forward
tipc: don't send FIN message from connectionless socket
ipvlan: fix multicast processing
ipvlan: fix various issues in ipvlan_process_multicast()
The current driver code gives the crash or gets hang while switching
the CPU frequency some time. The APSS CPU Clock divider is not glitch
free so it the APPS clock need to be switched for stable clock during
the change.
This patch adds the frequency change notifier for APSS CPU clock. It
changes the parent of this clock to stable PLL FEPLL500 for
PRE_RATE_CHANGE event. This event will be generated before actual
clock set operations. The clock set operation will again change its
corresponding parent by getting the same from frequency table.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
[sboyd@codeaurora.org: Indent less in probe]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In the actual implementation ether_addr_equal function tests for equality to 0
when returning. It seems in commit 0d74c4 it is somehow overlooked to change
this operator to reflect the actual function.
Signed-off-by: Cihangir Akturk <cakturk@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The 80211.tmpl DocBook file was removed in commit 819bf59376 ("docs-rst:
sphinxify 802.11 documentation"), but the 80211.xml target was re-added to
the Makefile by commit 7ddedebb03 ("ALSA: doc: ReSTize
writing-an-alsa-driver document"), leading to a failure when building the
documentation:
*** No rule to make target 'Documentation/DocBook/80211.xml', needed by
'Documentation/DocBook/80211.aux.xml'.
cc: stable@vger.kernel.org
Signed-off-by: John Brooks <john@fastquake.com>
Mea-culpa-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Fixing the gmac4 mdio write access to use MII_GMAC4_WRITE only instead of
OR together with MII_WRITE.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip is the same as RTL8168, but its device id is 0x8161.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 73b62bd085 ("virtio-net:
remove the warning before XDP linearizing"), there's no users for
bpf_warn_invalid_xdp_buffer(), so remove it. This is a revert for
commit f23bc46c30.
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Networking stack accelerate vlan tag handling by
keeping topmost vlan header in skb. This works as
long as packet remains in OVS datapath. But during
OVS upcall vlan header is pushed on to the packet.
When such packet is sent back to OVS datapath, core
networking stack might not handle it correctly. Following
patch avoids this issue by accelerating the vlan tag
during flow key extract. This simplifies datapath by
bringing uniform packet processing for packets from
all code paths.
Fixes: 5108bbaddc ("openvswitch: add processing of L3 packets").
CC: Jarno Rajahalme <jarno@ovn.org>
CC: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different namespaces might have different requirements to reuse
TIME-WAIT sockets for new connections. This might be required in
cases where different namespace applications are in place which
require TIME_WAIT socket connections to be reduced independently
of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Christopher Covington reported a crash on aarch64 on recent Fedora
kernels:
kernel BUG at ./include/linux/scatterlist.h:140!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 2 PID: 752 Comm: cryptomgr_test Not tainted 4.9.0-11815-ge93b1cc #162
Hardware name: linux,dummy-virt (DT)
task: ffff80007c650080 task.stack: ffff800008910000
PC is at sg_init_one+0xa0/0xb8
LR is at sg_init_one+0x24/0xb8
...
[<ffff000008398db8>] sg_init_one+0xa0/0xb8
[<ffff000008350a44>] test_acomp+0x10c/0x438
[<ffff000008350e20>] alg_test_comp+0xb0/0x118
[<ffff00000834f28c>] alg_test+0x17c/0x2f0
[<ffff00000834c6a4>] cryptomgr_test+0x44/0x50
[<ffff0000080dac70>] kthread+0xf8/0x128
[<ffff000008082ec0>] ret_from_fork+0x10/0x50
The test vectors used for input are part of the kernel image. These
inputs are passed as a buffer to sg_init_one which eventually blows up
with BUG_ON(!virt_addr_valid(buf)). On arm64, virt_addr_valid returns
false for the kernel image since virt_to_page will not return the
correct page. Fix this by copying the input vectors to heap buffer
before setting up the scatterlist.
Reported-by: Christopher Covington <cov@codeaurora.org>
Fixes: d7db7a882d ("crypto: acomp - update testmgr with support for acomp")
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now that dax_iomap_fault() calls ->iomap_begin() without entry lock, we
can use transaction starting in ext4_iomap_begin() and thus simplify
ext4_dax_fault(). It also provides us proper retries in case of ENOSPC.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently ->iomap_begin() handler is called with entry lock held. If the
filesystem held any locks between ->iomap_begin() and ->iomap_end()
(such as ext4 which will want to hold transaction open), this would cause
lock inversion with the iomap_apply() from standard IO path which first
calls ->iomap_begin() and only then calls ->actor() callback which grabs
entry locks for DAX (if it faults when copying from/to user provided
buffers).
Fix the problem by nesting grabbing of entry lock inside ->iomap_begin()
- ->iomap_end() pair.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The only case when we do not finish the page fault completely is when we
are loading hole pages into a radix tree. Avoid this special case and
finish the fault in that case as well inside the DAX fault handler. It
will allow us for easier iomap handling.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently dax_iomap_rw() takes care of invalidating page tables and
evicting hole pages from the radix tree when write(2) to the file
happens. This invalidation is only necessary when there is some block
allocation resulting from write(2). Furthermore in current place the
invalidation is racy wrt page fault instantiating a hole page just after
we have invalidated it.
So perform the page invalidation inside dax_iomap_actor() where we can
do it only when really necessary and after blocks have been allocated so
nobody will be instantiating new hole pages anymore.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently invalidate_inode_pages2_range() and invalidate_mapping_pages()
just delete all exceptional radix tree entries they find. For DAX this
is not desirable as we track cache dirtiness in these entries and when
they are evicted, we may not flush caches although it is necessary. This
can for example manifest when we write to the same block both via mmap
and via write(2) (to different offsets) and fsync(2) then does not
properly flush CPU caches when modification via write(2) was the last
one.
Create appropriate DAX functions to handle invalidation of DAX entries
for invalidate_inode_pages2_range() and invalidate_mapping_pages() and
wire them up into the corresponding mm functions.
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
So far we did not return BH_New buffers from ext2_get_blocks() when we
allocated and zeroed-out a block for DAX inode to avoid racy zeroing in
DAX code. This zeroing is gone these days so we can remove the
workaround.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If mce_device_init() fails then the mce device pointer is NULL and the
AMD mce code happily dereferences it.
Add a sanity check.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The attempt to prevent overwriting an active state resulted in a
disaster which effectively disables all dynamically allocated hotplug
states.
Cleanup the mess.
Fixes: dc280d9362 ("cpu/hotplug: Prevent overwriting of callbacks")
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit beb0babfb7 ("korina: disable napi on close and restart")
introduced calls to napi_disable() that were missing before,
unfortunately this leaves a small window during which NAPI has a chance
to run, yet we just freed resources since korina_free_ring() has been
called:
Fix this by disabling NAPI first then freeing resource, and make sure
that we also cancel the restart task before doing the resource freeing.
Fixes: beb0babfb7 ("korina: disable napi on close and restart")
Reported-by: Alexandros C. Couloumbis <alex@ozo.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
