A negative devlength won't get noticed and clean up:
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
UBI ioctl's do not work when running 64-bit kernel and 32-bit
user-land. Fix this by adding the compat_ioctl method.
Also, UBI serializes all ioctls, so more than one ioctl at a time
is not a problem. Amd UBI does not seem to depend on anything else,
so use unlocked_ioctl instead of ioctl (no BKL needed).
Reported-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Some ioctl's in UBI are enabled only when debugging is switched
on. There is not particular reason for this, just noone needed
them. However, some people need the now for their user-space
development. Thus, allow these ioctl's even if UBI debugging
is disabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds ioctl to check if an LEB is mapped or not (as a
debugging option so far).
[Re-named ioctl to make it look the same as the other one and made
some minor stylistic changes. Artem Bityutskiy.]
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds ioctl for the LEB unmap operation (as a debugging
option so far).
[Re-named ioctl to make it look the same as the other one and made
some minor stylistic changes. Artem Bityutskiy.]
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch adds ioctl for the LEB map operation (as a debugging
option so far).
[Re-named ioctl to make it look the same as the other one and made
some minor stylistic changes. Artem Bityutskiy.]
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Fix compile by removing remaining omap specific gpio
calls. Based on earlier patches by Jarkko Nikula.
Also remove old GPIO key code, there is already a patch
to do this with gpio_keys.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Which means if inftl or similar are loaded with it (which is a dumb thing
to do admittedly) it may oops.
Closes#8108
[dwmw2: change error to -EROFS to match write-protected flash]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (67 commits)
[MTD] [MAPS] Fix printk format warning in nettel.c
[MTD] [NAND] add cmdline parsing (mtdparts=) support to cafe_nand
[MTD] CFI: remove major/minor version check for command set 0x0002
[MTD] [NAND] ndfc driver
[MTD] [TESTS] Fix some size_t printk format warnings
[MTD] LPDDR Makefile and KConfig
[MTD] LPDDR extended physmap driver to support LPDDR flash
[MTD] LPDDR added new pfow_base parameter
[MTD] LPDDR Command set driver
[MTD] LPDDR PFOW definition
[MTD] LPDDR QINFO records definitions
[MTD] LPDDR qinfo probing.
[MTD] [NAND] pxa3xx: convert from ns to clock ticks more accurately
[MTD] [NAND] pxa3xx: fix non-page-aligned reads
[MTD] [NAND] fix nandsim sched.h references
[MTD] [NAND] alauda: use USB API functions rather than constants
[MTD] struct device - replace bus_id with dev_name(), dev_set_name()
[MTD] fix m25p80 64-bit divisions
[MTD] fix dataflash 64-bit divisions
[MTD] [NAND] Set the fsl elbc ECCM according the settings in bootloader.
...
Fixed up trivial debug conflicts in drivers/mtd/devices/{m25p80.c,mtd_dataflash.c}
[dwmw2: updated and made to still register whole device first]
Signed-off-by: Philip Rakity <pakity@yahoo.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The NOR Flash memory K8P2815UQB from Samsung uses the major version
number '0'. Add a quirk to cope with it.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (53 commits)
serial: Add driver for the Cell Network Processor serial port NWP device
powerpc: enable dynamic ftrace
powerpc/cell: Fix the prototype of create_vma_map()
powerpc/mm: Make clear_fixmap() actually work
powerpc/kdump: Use ppc_save_regs() in crash_setup_regs()
powerpc: Export cacheable_memzero as its now used in a driver
powerpc: Fix missing semicolons in mmu_decl.h
powerpc/pasemi: local_irq_save uses an unsigned long
powerpc/cell: Fix some u64 vs. long types
powerpc/cell: Use correct types in beat files
powerpc: Use correct type in prom_init.c
powerpc: Remove unnecessary casts
mtd/ps3vram: Use _PAGE_NO_CACHE in memory ioremap
mtd/ps3vram: Use msleep in waits
mtd/ps3vram: Use proper kernel types
mtd/ps3vram: Cleanup ps3vram driver messages
mtd/ps3vram: Remove ps3vram debug routines
mtd/ps3vram: Add modalias support to the ps3vram driver
mtd/ps3vram: Add ps3vram driver for accessing video RAM as MTD
powerpc: Fix iseries drivers build failure without CONFIG_VIOPATH
...
When I review ocfs2 code, find there are 2 typos to "successfull". After
doing grep "successfull " in kernel tree, 22 typos found totally -- great
minds always think alike :)
This patch fixes all the similar typos. Thanks for Randy's ack and comments.
Signed-off-by: Coly Li <coyli@suse.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use _PAGE_NO_CACHE for gpu memory ioremap. Also,
add __iomem attribute to gpu memory pointer and
change use of memset() to memset_io().
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Replace the use of udelay() with msleep() in the looping wait routines
ps3vram_notifier_wait() and ps3vram_wait_ring().
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Replace the use of stdint.h types with kernel types
in the ps3vram driver.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cleanup the ps3vram driver messages. Add a new struct device pointer
variable dev to struct ps3vram_priv and use dev_dbg(), pr_dbg(), etc.
where appropriate.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove the ps3vram debug routines ps3vram_dump_ring() and
ps3vram_dump_reports(). These routines are not needed.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update ps3vram driver to use the new ps3 three id modalias support.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add ps3vram driver, which exposes unused video RAM on the PS3 as a MTD
device suitable for storage or swap. Fast data transfer is achieved
using a local cache in system RAM and DMA transfers via the GPU.
Signed-off-by: Vivien Chappelier <vivien.chappelier@free.fr>
Signed-off-by: Jim Paris <jim@jtan.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
The current ndfc driver only compiles under arch/ppc. This arch was
removed from the kernel. I notice the event entry for the ndfc in
Kconfig has been removed in 2.6.28.
This patch converts the ndfc to a proper OF (OpenFirmware) driver. I
can give a working example of the DTS if needed.
The patch has been in production use on the PIKA Warp Appliance and is
in use by others. The Warp basically boots from NAND, so the ndfc driver
is very important to us.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Acked-By: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We have two components to manage LPDDR flash memories in Linux.
1. It is a driver for chip probing and reading its capabilities
2. It is a device operations driver.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Acked-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Physmap is a generic map driver for different platforms and flash types.
We added support of LPDDR to physmap.
All changes here are related to introduction of new pfow_base parameter.
This parameter is valid in case of LPDDR chips only.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Acked-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Driver which handles device command operation.
Details on device operations are available here:
http://www.numonyx.com/Documents/Datasheets/DS-315768_Velocity-Discrete.pdf
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Acked-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
LPDDR flash chips are based on completely new kind of chips probing.
Device capabilities are available via special request.
We sent field request command which contains Major and Minor numbers - and
recieve corresponend value.
All requests are performed within PFOW window.
Detailed information about qinfo records can be found here:
http://www.numonyx.com/Documents/Datasheets/DS-315768_Velocity-Discrete.pdf
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Acked-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The various fields in NDTR{01} are in units of clock ticks minus one, but the
ns2cycle macro mistakenly adds one, inflating the number of clock ticks and
making it impossible to set any of these fields to zero.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Reads from non-page-aligned addresses were broken because while the
address to read from was correctly written to NDCB*, a full page was
always read. Fix this by ignoring the column and only using the page
address.
I suspect this whole-page behavior is due to the controller's need to
read the entire page in order to generate correct ECC. In the non-ECC
case this could be optimized to use the column address, and to set the
read length to what is being requested rather than the length of an
entire page.
Signed-off-by: Matt Reimer <mreimer@vpop.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix sched.h references:
build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1326: error: dereferencing pointer to incomplete type
build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1326: error: 'PF_MEMALLOC' undeclared (first use in this function)
build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1328: error: dereferencing pointer to incomplete type
build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1335: error: dereferencing pointer to incomplete type
build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1335: error: 'PF_MEMALLOC' undeclared (first use in this function)
build-r7149.out:make[4]: *** [drivers/mtd/nand/nandsim.o] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This set of patches introduces calls to the following set of functions:
usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)
In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:
USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC
An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)
@r5@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
- \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)
@inc@
@@
#include <linux/usb.h>
@depends on !inc && (r1||r5)@
@@
+ #include <linux/usb.h>
#include <linux/usb/...>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
MTD has recently been upgraded for 64-bit support, see commit
number 69423d99fc in the
mtd-2.6.git tree (git://git.infradead.org/mtd-2.6.git)
or see this URL:
http://git.infradead.org/mtd-2.6.git?a=commit;h=69423d99fc182a81f3c5db3eb5c140acc6fc64be
Some variables in MTD data structures which were 32-bit
became 64-bit. Namely, the 'size' field in 'struct mtd_info'
and the 'addr'/'len' fields in 'struct erase_info'. This
means we have to use 'do_div' to divide them.
This patch fixes the following linking error:
ERROR: "__umoddi3" [drivers/mtd/devices/m25p80.ko] undefined!
This patch changes divisions of 64-bit variable so that they use
'do_div'. This patch also change some print placeholders to
get rid of gcc warnings.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
MTD has recently been upgraded for 64-bit support, see commit
number 69423d99fc in the
mtd-2.6.git tree (git://git.infradead.org/mtd-2.6.git)
or see this URL:
http://git.infradead.org/mtd-2.6.git?a=commit;h=69423d99fc182a81f3c5db3eb5c140acc6fc64be
Some variables in MTD data structures which were 32-bit
became 64-bit. Namely, the 'size' field in 'struct mtd_info'
and the 'addr'/'len' fields in 'struct erase_info'. This
means we have to use 'do_div' to divide them.
This patch fixes the following linking error:
ERROR: "__udivdi3" [drivers/mtd/devices/mtd_dataflash.ko] undefined!
ERROR: "__umoddi3" [drivers/mtd/devices/mtd_dataflash.ko] undefined!
This patch changes divisions of 64-bit variable so that they use
'do_div'. This patch also change some print placeholders to
get rid of gcc warnings.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
UBI has 2 RB-trees to implement PEB protection, which is too
much for simply prevent PEB from being moved for some time.
This patch implements this using lists. The benefits:
1. No need to allocate protection entry on each PEB get.
2. No need to maintain balanced trees and walk them.
Signed-off-by: Xiaochuan-Xu <xiaochuan-xu@cqu.edu.cn>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch modifies @struct ubi_wl_entry and adds union which
contains only one element so far. This is just a preparation
for further changes which will kill the protection tree and
make UBI use a list instead.
Signed-off-by: Xiaochuan-Xu <xiaochuan-xu@cqu.edu.cn>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Netwinder was using gpio_xxx names which could clash with the GPIO
layer. Add a 'nw_' prefix to ensure that these remain separate.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Have most uses of OMAP_GPIO_IRQ() use gpio_to_irq() instead.
Calls used for table initialization are left alone, at least
this time around.
(This patch is for code in both the OMAP tree and mainline.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
More switchover to the cross-platform GPIO interface:
use gpio_direction_input(), not an OMAP-specific call.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch replaces some legacy OMAP GPIO calls with the "new" (not
really, any more!) calls that work on most platforms.
The calls addressed by this patch are the simple ones to get and set
values ... for code that's in mainline, including the implementations
of those calls.
Except for the declarations and definitions of those calls, all of
these changes were performed by a simple SED script. Plus, a few
"if() set() else set()" branches were merged by hand.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ECCM maybe set in bootloader, Get ECCM settings from the bootloader,
can avoid the image written by bootloader cannot read out by kernel.
But the limitation of doing it this way is that, it could break large page
NAND if it is written with NAND disabled in u-boot and read with NAND
enabled, or vice versa.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Delete extra kernel-doc notation for struct fields and function
parameters that don't exist:
Warning(include/linux/mtd/nand.h:428): Excess struct/union/enum/typedef member 'wq' description in 'nand_chip'
Warning(include/linux/mtd/nand.h:428): Excess struct/union/enum/typedef member 'datbuf' description in 'nand_chip'
Warning(include/linux/mtd/nand.h:428): Excess struct/union/enum/typedef member 'oobbuf' description in 'nand_chip'
Warning(include/linux/mtd/nand.h:428): Excess struct/union/enum/typedef member 'oobdirty' description in 'nand_chip'
Warning(include/linux/mtd/nand.h:428): Excess struct/union/enum/typedef member 'data_poi' description in 'nand_chip'
Warning(drivers/mtd/nand/nand_base.c:2527): Excess function parameter 'maxchips' description in 'nand_scan_tail'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The mtd partition parser returns an allocated pointer array of
mtd_partition. The caller must free it. The array is used only for
add_mtd_partitions(), so free it just after the call.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
ARRAY_SIZE is more concise to use when the size of an array is divided by
the size of its type or the size of its first element.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@i@
@@
#include <linux/kernel.h>
@depends on i using "paren.iso"@
type T;
T[] E;
@@
- (sizeof(E)/sizeof(E[...]))
+ ARRAY_SIZE(E)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The current method for always showing physmap compat address, size, and
width is a bit confusing. If length is set to 0, then the address and
width are still shown but silently unused. The physmap code itself
already has logic which sets compat based on length, so just pull that out
and into the Kconfig to make everything clear.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Bryan Wu <Bryan.Wu@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Base versions handle constant folding just fine.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
MTD internal API presently uses 32-bit values to represent
device size. This patch updates them to 64-bits but leaves
the external API unchanged. Extending the external API
is a separate issue for several reasons. First, no one
needs it at the moment. Secondly, whether the implementation
is done with IOCTLs, sysfs or both is still debated. Thirdly
external API changes require the internal API to be accepted
first.
Note that although the MTD API will be able to support 64-bit
device sizes, existing drivers do not and are not required
to do so, although NAND base has been updated.
In general, changing from 32-bit to 64-bit values cause little
or no changes to the majority of the code with the following
exceptions:
- printk message formats
- division and modulus of 64-bit values
- NAND base support
- 32-bit local variables used by mtdpart and mtdconcat
- naughtily assuming one structure maps to another
in MEMERASE ioctl
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Nandsim consumes ~2x more RAM than the density of simulated device.
It becomes critical if we need to simulate 256MB NAND and run stress tests
on it.
We investigated the reasons. nandsim allocates space for pages using kmalloc
function. The size of LP nand page is 2112 bytes.
kmalloc gets space from slab pools by chunks 2^n. So if we need to kmalloc
2112 bytes, 4096 bytes will be consumed by system.
The best way to avoid this issue would be using kmem_cache allocations. AFAIK
this mechanism specially designed to handle cases when arrays of allocations
are used.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Tested-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a new module parameter 'cache_file' which causes nandsim
to use that file instead of memory to cache nand data.
Using a file allows the simulation of NAND that is bigger
than the available memory.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
nand_base sometimes reads only 2 bytes of a 4 byte id.
It is OK. Do not print a warning in that case.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function init_impa7 does not need to be global, and
this patch makes it static by adding the needed keyword
to drivers/mtd/maps/impa7.c.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function init_redwood_flash is needlessly defined global,
make it static by this patch.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function init_msp_flash, which is not used outside of
drivers/mtd/maps/pmcmsp-flash.c, can become static. This
patch adds the needed keyword.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function h720x_mtd_init is not used outside of the file
drivers/mtd/maps/h720x-flash.c and can therefore become static.
This patch adds the necessary keyword.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function init_mbx can become static, because it is not used
outside the file drivers/mtd/maps/mbx860.c. This patch adds the
needed keyword.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function init_vmax301 is needlessly defined global in
drivers/mtd/maps/vmax301.c, and this patch makes it static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The symbol init_fortunet is needlessly defined global in
drivers/mtd/maps/fortunet.c. Make it static and clean up
the kernel global namespace.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The symbol alchemy_mtd_init does not need to be global, so make it
static in drivers/mtd/maps/alchemy-flash.c.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The symbol ipaq_mtd_init is not used anywhere outside of
drivers/mtd/maps/ipaq-flash.c, so make it static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The symbol init_dbox2_flash is not used outside of the file
drivers/mtd/maps/dbox2-flash.c, so make it static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The module init function init_flagadm does not need to be global,
so add the needed keyword to drivers/mtd/maps/cfi_flagadm.c.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function init_oct5066 is needlessly defined global in
drivers/mtd/maps/octagon-5066.c. Make it static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The init_edb7312nor function is needlessly defined global in
drivers/mtd/maps/edb7312.c, and this patch makes it static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function init_sbc82xx_flash is needlessly defined global in
drivers/mtd/maps/wr_sbc82xx_flash.c, and this patch makes it static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function init_rpxlite, which is not used outside of
drivers/mtd/maps/rpxlite.c, can become static. Add the
needed keyword.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The init_tqm_mtd function does not need to be defined globally
in drivers/mtd/maps/tqm8xxl.c. Make it static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The functions uclinux_mtd_cleanup and uclinux_mtd_init do
not heed to be global. Add the needed keyword to the file
drivers/mtd/maps/uclinux.c to make these functions static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The symbols lart_flash_init, lart_flash_exit are needlessly
defined global in drivers/mtd/devices/lart.c, so make them
static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function init_sbc8240_mtd is not called from outside the
module drivers/mtd/maps/sbc8240.c where it is defined, so it
can become static. Add the needed keyword.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The function init_sharpsl is needlessly defined global.
Make it static by adding the needed keyword to the file
drivers/mtd/maps/sharpsl-flash.c, where the function is
defined.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Return with correct error code (-ENOMEM) from ubi_attach_mtd_dev() upon
failing vmalloc().
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When a PEB is moved and a write error happens, UBI switches
to R/O mode, which is wrong, because we just copy the data
and may select a different PEB and re-try this. This patch
fixes WL worker's behavior.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Make sure the resources had not already been freed before
freeing them in the error path of the WL worker function.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
We cannot call 'ubi_wl_get_peb()' with @ubi->buf_mutex locked,
because 'ubi_wl_get_peb()' may force erasure, which, in turn,
may call 'torture_peb()' which also locks the @ubi->buf_mutex
and deadlocks.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The 'ubi_io_read_vid_hdr()' and 'ubi_io_read_ec_hdr()' function
have the 'verbose' argument which controls whether they should
print a warning if the VID/EC header was not found or was corrupted.
Some callers require the headers to be OK, and pass 1. Some allow
a corrupted/not present header, and pass 0.
if (UBI_IO_DEBUG)
verbose = 1;
And UBI_IO_DEBUG is 1 if CONFIG_MTD_UBI_DEBUG_MSG_BLD is true. So in
this case the warning is printed all the time. This confuses people.
Thus, do not print the messages as warnings if UBI_IO_DEBUG is true,
but print them as debugging messages instead.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
STM 2Gb flash is a large-page NAND flash. Set operations accordingly.
This field is dereferenced without a check in several places resulting in
OOPS.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Eric Miao <ymiao3@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
pci_get_device increments a reference count that should be decremented
using pci_dev_put.
The semantic patch that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S,S1;
position p1,p2,p3;
expression E,E1;
type T,T1;
expression *ptr != NULL;
@@
(
if ((x@p1 = pci_get_device(...)) == NULL) S
|
x@p1 = pci_get_device(...);
)
... when != pci_dev_put(...,(T)x,...)
when != if (...) { <+... pci_dev_put(...,(T)x,...) ...+> }
when != true x == NULL || ...
when != x = E
when != E = (T)x
when any
(
if (x == NULL || ...) S1
|
if@p2 (...) {
... when != pci_dev_put(...,(T1)x,...)
when != if (...) { <+... pci_dev_put(...,(T1)x,...) ...+> }
when != x = E1
when != E1 = (T1)x
(
return \(0\|<+...x...+>\|ptr\);
|
return@p3 ...;
)
}
)
@ script:python @
p1 << r.p1;
p3 << r.p3;
@@
print "* file: %s pci_get_device: %s return: %s" % (p1[0].file,p1[0].line,p3[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'linux-next' of git://git.infradead.org/~dedekind/ubi-2.6:
UBI: Don't exit from ubi_thread until kthread_should_stop() is true
UBI: fix EBADMSG handling
Where devices only have one consumer, passing a consumer clock ID
has no real benefit. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As suggested by Andrew Morton, remove memzero() - it's not supported
on other architectures so use of it is a potential build breaking bug.
Since the compiler optimizes memset(x,0,n) to __memzero() perfectly
well, we don't miss out on the underlying benefits of memzero().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch fixes following build error:
CC drivers/mtd/nand/fsl_upm.o
drivers/mtd/nand/fsl_upm.c: In function 'fun_chip_init':
drivers/mtd/nand/fsl_upm.c:168: warning: passing argument 2 of 'of_mtd_parse_partitions' from incompatible pointer type
drivers/mtd/nand/fsl_upm.c:168: warning: passing argument 3 of 'of_mtd_parse_partitions' from incompatible pointer type
drivers/mtd/nand/fsl_upm.c:168: error: too many arguments to function 'of_mtd_parse_partitions'
make[1]: *** [drivers/mtd/nand/fsl_upm.o] Error 1
The breakage was introduced in 69fd3a8d09
("[MTD] remove unused mtd parameter in of_mtd_parse_partitions()").
While at it, also add a check for the of_mtd_parse_partitions() return
value.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
physmap_flash_remove releases only last memory region. This causes
memory leak if multiple resources were provided.
This patch fixes this leakage by using devm_ functions.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes broken terminology added in the "m25p80.c erase enhance" patch,
which added a chip erase command but called it "block erase". There are
already two block erase commands; blocks are 4KiB or 32KiB. There's also
a sector erase (usually 64 KiB). Chip erase typically covers Megabytes.
OPCODE_BE ==> OPCODE_CHIP_ERASE
erase_block ==> erase_chip
[dbrownell@users.sourceforge.net: update sector erase comments too ]
Signed-off-by: Chen Gong <clumsycg@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit d0e8c47c58 ("m25p80.c extended jedec
support") added support for extended ids but seems to break on flashes
which don't have an extended id defined. If the table does not have an
extid defined, then we should ignore it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Michael Hennerich <Michael.Hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit d0e8c47c58 ("m25p80.c extended jedec
support") added support for extended ids but in the process managed to
break detection of all flashes.
The ext jedec id check was inserted into an if statement that lacked
braces, and it did not add the required braces. As such, the detection
routine always returns the first entry in the SPI flash list.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Include <linux/dma-mapping.h> and <linux/io.h>, not files from <asm/*>
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If ubi_thread() exits but kthread_should_stop() is not true
then kthread_stop() will never return and cleanup thread
will forever stay in "D" state.
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
'ubi_io_read_data()' may return EBADMSG in case of an ECC error,
and we should not panic because of this. We have CRC32 checksum
and may check the data. So just ignore the EBADMSG error.
This patch also fixes a minor spelling error at the same time.
Signed-off-by: Zoltan Sogor <weth@inf.u-szeged.hu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
For "unlock" cycles to 16bit devices in 8bit compatibility mode we need
to use the byte addresses 0xaaa and 0x555. These effectively match
the word address 0x555 and 0x2aa, except the latter has its low bit set.
Most chips don't care about the value of the 'A-1' pin in x8 mode,
but some -- like the ST M29W320D -- do. So we need to be careful to
set it where appropriate.
cfi_send_gen_cmd is only ever passed addresses where the low byte
is 0x00, 0x55 or 0xaa. Of those, only addresses ending 0xaa are
affected by this patch, by masking in the extra low bit when the device
is known to be in compatibility mode.
[dwmw2: Do it only when (cmd_ofs & 0xff) == 0xaa]
v4: Fix stupid typo in cfi_build_cmd_addr that failed to compile
I'm writing this patch way to late at night.
v3: Bring all of the work back into cfi_build_cmd_addr
including calling of map_bankwidth(map) and cfi_interleave(cfi)
So every caller doesn't need to.
v2: Only modified the address if we our device_type is larger than our
bus width.
Cc: stable@kernel.org
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Finally move registration of sharpsl-nand device to board-specific code.
sharpsl nand driver is now clean and simple.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Merge mtd_info and nand_chip info special struct and
make it drvdata instead of plain static variable.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Start cleanup of sharpsl_nand driver. Convert it to platform driver.
Corresponding device is temprorary registered in sharpsl.c but will be
later moved to corresponding board files.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
replace open_bdev_excl/close_bdev_excl with variants taking fmode_t.
superblock gets the value used to mount it stored in sb->s_mode
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
To keep the size of changesets sane we split the switch by drivers;
to keep the damn thing bisectable we do the following:
1) rename the affected methods, add ones with correct
prototypes, make (few) callers handle both. That's this changeset.
2) for each driver convert to new methods. *ALL* drivers
are converted in this series.
3) kill the old (renamed) methods.
Note that it _is_ a flagday; all in-tree drivers are converted and by the
end of this series no trace of old methods remain. The only reason why
we do that this way is to keep the damn thing bisectable and allow per-driver
debugging if anything goes wrong.
New methods:
open(bdev, mode)
release(disk, mode)
ioctl(bdev, mode, cmd, arg) /* Called without BKL */
compat_ioctl(bdev, mode, cmd, arg)
locked_ioctl(bdev, mode, cmd, arg) /* Called with BKL, legacy */
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* git://git.infradead.org/mtd-2.6: (69 commits)
Revert "[MTD] m25p80.c code cleanup"
[MTD] [NAND] GPIO driver depends on ARM... for now.
[MTD] [NAND] sh_flctl: fix compile error
[MTD] [NOR] AT49BV6416 has swapped erase regions
[MTD] [NAND] GPIO NAND flash driver
[MTD] cmdlineparts documentation change - explain where mtd-id comes from
[MTD] cfi_cmdset_0002.c: Add Macronix CFI V1.0 TopBottom detection
[MTD] [NAND] Fix compilation warnings in drivers/mtd/nand/cs553x_nand.c
[JFFS2] Write buffer offset adjustment for NOR-ECC (Sibley) flash
[MTD] mtdoops: Fix a bug where block may not be erased
[MTD] mtdoops: Add a magic number to logged kernel oops
[MTD] mtdoops: Fix an off by one error
[JFFS2] Correct parameter names of jffs2_compress() in comments
[MTD] [NAND] sh_flctl: add support for Renesas SuperH FLCTL
[MTD] [NAND] Bug on atmel_nand HW ECC : OOB info not correctly written
[MTD] [MAPS] Remove unused variable after ROM API cleanup.
[MTD] m25p80.c extended jedec support (v2)
[MTD] remove unused mtd parameter in of_mtd_parse_partitions()
[MTD] [NAND] remove dead Kconfig associated with !CONFIG_PPC_MERGE
[MTD] [NAND] driver extension to support NAND on TQM85xx modules
...
This reverts commit 75d0ee2202.
Although it seems ObviouslyCorrect™, the spi_write() call uses DMA,
while spi_write_then_read() does not. Since our buffer is on the stack,
we must use the latter even though we don't actually want to read
anything back.
Pointed out by David Brownell <david-b@pacbell.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Not all architectures provide readsb(). We should probably move to using
ioread8_rep() instead.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix compile error because the first patch was broken -- the file got
truncated.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The CFI information read from AT49BV6416 lists the erase regions in the
wrong order, causing problems when trying to erase or update the first
or last 64KiB block.
Work around this by inverting the "top boot" flag, which will
effectively reverse the order of the erase regions.
This chip is obsolete, but it's used in some existing designs.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The patch adds support for NAND flashes connected to GPIOs.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds TopBottom detection for most Macronix chips with CFI V1.0.
The main purpose of this patch is to add detection of the MX29LV400C B
used on the LaCie Ethernet Disk mini V2 NAS.
It detects the following parts correctly:-
MX28F640C3B T
MX29LV002C B
MX29LV002NC B
MX29LV004C T
MX29LV400C T/B
MX29LV800C T/B
MX29LV160C T/B
MX29SL800C T/B
MX29SL802C T/B
It detects the following uniform part as bottom but it should work
correctly:-
MX29LV040C
For T parts it causes the erase block table to be reversed correctly.
For other parts it avoids the bogus "Assuming top" message.
It does not detect the following correctly:-
MX28F640C3B B
MX29LV002C T
MX29LV002NC T
MX29LV004C B
MX29SL400C T/B
MX29SL402C T/B
If desired I could supply a more complicated patch to handle these as
well.
Only the MX29LV400C B has been physically tested; others were checked
against their data sheets.
Signed-off-by: Christopher Moore <moore@free.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This makes the driver erase a block when it doesn't find any
existing saved log messages which is safer than assuming the
flash was already erased.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a magic number to logged kernel oops messages so that they
can be more accurately detected rather than just having to rely
on the sequence number. This also allows easier detection of
saved crashes by userspace.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix an off by one error in the mtdoops driver
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
USB should not be having it's own printk macros, so remove info() and
use the system-wide standard of dev_info() wherever possible.
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
UIO: Fix mapping of logical and virtual memory
UIO: add automata sercos3 pci card support
UIO: Change driver name of uio_pdrv
UIO: Add alignment warnings for uio-mem
Driver core: add bus_sort_breadthfirst() function
NET: convert the phy_device file to use bus_find_device_by_name
kobject: Cleanup kobject_rename and !CONFIG_SYSFS
kobject: Fix kobject_rename and !CONFIG_SYSFS
sysfs: Make dir and name args to sysfs_notify() const
platform: add new device registration helper
sysfs: use ilookup5() instead of ilookup5_nowait()
PNP: create device attributes via default device attributes
Driver core: make bus_find_device_by_name() more robust
usb: turn dev_warn+WARN_ON combos into dev_WARN
debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
debug: Introduce a dev_WARN() function
sysfs: fix deadlock
device model: Do a quickcheck for driver binding before doing an expensive check
Driver core: Fix cleanup in device_create_vargs().
Driver core: Clarify device cleanup.
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
module: remove CONFIG_KMOD in comment after #endif
remove CONFIG_KMOD from fs
remove CONFIG_KMOD from drivers
Manually fix conflict due to include cleanups in drivers/md/md.c
This updates most of the OMAP drivers which are in mainline to switch to
using the cross-platform GPIO calls instead of the older OMAP-specific
ones.
This is all fairly brainless/obvious stuff. Probably the most interesting
bit is to observe that the omap-keypad code seems to now have a portable
core that could work with non-OMAP matrix keypads. (That would improve
with hardware IRQ debouncing enabled, of course...)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Straight forward conversions to CONFIG_MODULE; many drivers
include <linux/kmod.h> conditionally and then don't have any
other conditional code so remove it from those.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: video4linux-list@redhat.com
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-ppp@vger.kernel.org
Cc: dm-devel@redhat.com
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Several Renesas SuperH CPU has FLCTL. The FLCTL support NAND Flash.
This driver support SH7723.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The functions that write the OOB info (on hardware ECC only) use the
HW_SYNDROME method.
This is not correct : the start position is "pos = eccsize + chunk" and
should be eccsize. So, the standard (nand_write_oob_std) function should
be used. This patch corrects this by using NAND_ECC_HW instead of
NAND_ECC_HW_SYNDROME.
This has only been tested on small pages nand flash.
(if anyone can test it on large pages that would be great).
kernel version : 2.6.27-rc2 (current git mtd-2.6)
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
Removed the Kconfig associated with 'NDFC NanD Flash Controller'.
We can't enable !CONFIG_PPC_MERGE so there is no way to enable
this. Additionally the code needs to get updated for arch/powerpc.
For the time being lets just remove the Kconfig option so we can
actually remove CONFIG_PPC_MERGE.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch extends the FSL UPM NAND driver from Anton Vorontsov to
support hardware which does not have the R/B pin of the NAND chip
connected, like the TQM8548 module:
- The OF_GPIO dependency has been removed from the Kconfig option
because GPIO is not needed. The relevant gpio_* function are then
stubbed out in <linux/gpio.h>.
- It re-introduces the chip-delay property to define an appropriate
maximum delay time (tR) required for read operations. The binding
will be documented in a separate patch.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
- Get rid of fsl,wait-pattern and fsl,wait-write. I think this isn't
chip-specific, and we should always do waits. I saw one board that
didn't need fsl,wait-pattern, but I assume this was the exception
that proves the rule;
- Get rid of chip-delay. Today there are no users for this, and if
anyone really need this they should push the OF bindings beforehand;
- Now flash chips should be child nodes of the FSL UPM NAND controller;
- Implement OF partition parsing.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch makes debugging a missconfigured UBI a bit easier
by providing the needed information in the boot log.
Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
We can benefit from knowing that the file system no longer cares about
the contents of certain sectors, by throwing them away immediately and
then never having to garbage collect them, and using the extra free
space to make our operations more efficient. Do so.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When iterating over a chain in reverse (oldest block first), this
patch correctly marks the PUtable[] entry of the second to last erase
block of a chain as BLOCK_NIL, regardless of whether or not it can
format the last block successfully. Before, the second to last block
was only marked as pointing to BLOCK_NIL if INFTL_formatblock()
succeeded on the last block of the chain, which could potentially
result in an infinite loop if the block was worn out and refused to
format.
Signed-off-by: Daniel Rosenthal <danielrosenthal@acm.org>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
...since it only probes that
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Now that the needed helpers are exported, it becomes a nice simple
switch over. Closes#9420
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The patch fixes CFI issue with multipartitional devices leading to the
set of errors or even deadlock. The problem is CFI FL_SYNCING state race
with flash operations (e.g. erase suspend). It is reproduced by running
intensive writes on one JFFS2 partition and simultaneously performing
mount/unmount cycle on another partition of the same chip.
Signed-off-by: Alexander Belyakov <abelyako@googlemail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In case of error, the function add_volume returns an ERR pointer. The
result of IS_ERR, which is supposed to be used in a test as it is, is
here checked to be less than zero, which seems odd. We suggest to
replace this test by a simple IS_ERR test.
A simplified version of the semantic match that finds this problem is
as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@def0@
expression x;
position p0;
@@
x@p0 = add_volume(...)
@protected@
expression def0.x,E;
position def0.p0;
position p;
statement S;
@@
x@p0
... when != x = E
if (!IS_ERR(x) && ...) {<... x@p ...>} else S
@unprotected@
expression def0.x,E;
identifier fld;
position def0.p0;
position p != protected.p;
@@
x@p0
... when != x = E
* x@p->fld
// </smpl>
Signed-off-by: Julien Brunel <brunel@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Add copyright information for some of the AT91 header files.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some chips require a RESET after power-up (e.g. Micron MT29FxGxxxxx).
The first command sent is NAND_CMD_READID.
Issue a NAND_CMD_RESET in nand_scan_ident before reading the device id.
Tested with an MT29F4G08AAC.
Signed-off-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Very occasionally, (about one in a million) read operations are
ongoing after the timeout has expired. So, retry three times
while the ongoing bit remains set.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix offset of second word used for programming base address of memory
window. Also program tmio with offset of the FCR, not with physical
memory location.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for the integrated NAND flash controller of the
i.MX2 and i.MX3 family. It is tested on MX27 but should work on MX3
aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The MEMGETREGIONINFO ioctl() in mtdchar.c was clobbering user memory by
overwriting more than intended, due the size of struct mtd_erase_region_info
changing in commit 0ecbc81adf ('Support
for auto locking flash on power up').
Fix avoids this by copying struct members one by one with put_user(), as there
is no longer a convenient struct to use the size of as the length argument to
copy_to_user().
Signed-off-by: Zev Weiss <zevweiss@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Minor patch to help debugging of NAND detection.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch moves some attributes out from the platform data into the
dynamically created nand device. This results into a cleaner interface
and allows to use constant pxa3xx_nand_flash definitions.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch marks some attributes as 'const' which are set only once and
never be modified by the driver. There are some changes in parameter
list and variable declarations too which mark them as 'const'.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a MTD_NAND_PXA3xx_BUILTIN configuration variables which
allows to disable usage of builtin flash-type table. Not enabling this
option saves some space in the generated driver.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds 'flash' and 'num_flash' attributes to the platform data.
There was added code in the driver to iterate across these attributes in the
detect-flash routine. This is done similarly to the existing method
which uses a 'builtin_flash_types' field.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch moves the exported datastructures from the pxa3xx_nand.c driver
into the <mach/pxa3xx_nand.h> header. This is a plain movement without
any modification of the attributes.
This is the first one of a set of patches which:
* allows to specify used NAND flash in the platform code and allows to turn
off the old way to specify NAND characteristics in the driver. This way did
not worked well as these characteristics depend on the platform and can not be
derived from NAND id alone.
E.g. some NAND chips share the same ID (e.g. K9K8G08U0A and K9NBG08U5A) but
have different timings (which are written in the common driver currently and
must be modified there).
* adds 'const' annotations at various places
Further patches will be sent to the mtd-list.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Semun Lee <semun.lee@samsung.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since we're just parsing the tuple being passed to this function, we don't
need any device-specific information.
Also, remove the call to pcmcia_validate_cis() from pcmciamtd.c, since it
is already called by the PCMCIA core.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
It doesn't use LINUX_VERSION_CODE nor KERNEL_VERSION.
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of using own error or success codes, the PCMCIA code should rely on
the generic return values. Therefore, replace all occurrences of CS_SUCCESS
with 0.
CC: netdev@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Remove the three remaining pcmcia_get_configuration_info() users:
- pcmciamtd is marked broken anyway.
- serial_cs.c can access the relevant structs directly
- ipwireless didn't use the output
CC: linux-serial@vger.kernel.org
CC: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch for nand_ecc.c fixes three issues
- fix code so it also works on big endian architectures
- added a printk in case of an uncorrectable ecc error
- strengthen the test for correctable errors (decreasing the chance
that multiple bit faults by accident will be seen as correctable)
Note: the big endian code is only tested in a testbed (running on big endian
hardware) as I cannot rebuild and test a big endian kernel at the moment.
However the only thing that can go wrong is if <asm/byteorder.h> does not
give __BIG_ENDIAN in that case. In my eyes very unlikely.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/mtd/maps/amd76xrom.c
drivers/mtd/maps/ck804xrom.c
drivers/mtd/maps/esb2rom.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* master.kernel.org:/home/rmk/linux-2.6-arm: (38 commits)
[ARM] 5191/1: ARM: remove CVS keywords
[ARM] pxafb: fix the warning of incorrect lccr when lcd_conn is specified
[ARM] pxafb: add flag to specify output format on LDD pins when base is RGBT16
[ARM] pxafb: fix the incorrect configuration of GPIO77 as ACBIAS for TFT LCD
[ARM] 5198/1: PalmTX: PCMCIA fixes
[ARM] Fix a pile of broken watchdog drivers
[ARM] update mach-types
[ARM] 5196/1: fix inline asm constraints for preload
[ARM] 5194/1: update .gitignore
[ARM] add proc-macros.S include to proc-arm940 and proc-arm946
[ARM] 5192/1: ARM TLB: add v7wbi_{possible,always}_flags to {possible,always}_tlb_flags
[ARM] 5193/1: Wire up missing syscalls
[ARM] traps: don't call undef hook functions with spinlock held
[ARM] 5183/2: Provide Poodle LoCoMo GPIO names
[ARM] dma-mapping: provide sync_range APIs
[ARM] dma-mapping: improve type-safeness of DMA translations
[ARM] Kirkwood: instantiate the orion_spi driver in the platform code
[ARM] prevent crashing when too much RAM installed
[ARM] Kirkwood: Instantiate mv_xor driver
[ARM] Orion: Instantiate mv_xor driver for 5182
...
This patch improves the performance of the ecc generation code by a
factor of 18 on an INTEL D920 CPU, a factor of 7 on MIPS and a factor of 5
on ARM (NSLU2)
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
On OMAP3, the driver was occasionally not seeing the GPIO
interrupt. Adding a small delay of one register read
eliminates the problem.
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver had resided in the OMAP tree but is now to be in MTD.
Original authors were:
Jarkko Lavinen <jarkko.lavinen@nokia.com> and Juha Yrjölä
IRQ and DMA support written by Timo Teras
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
- add extended device information support
- add s25sl128 device support
Signed-off-by: Chen Gong <g.chen@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds an erase_block command to enhance erase operation
Signed-off-by: Chen Gong <g.chen@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Removed duplicated include <asm/div64.h> in
drivers/mtd/nand/nandsim.c.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The TMIO chips are only found (and thus tested) on ARM machines.
Moreover, we don't want the TMIO cells to be built if one of the TMIO
driver is not selected (which indirectly make the TMIO cells drivers
depend on ARM as well).
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch adds support for the NAND controller commonly found in
TMIO based MFDs.
Signed-off-by: Ian Molton <spyro@f2s.com>
Acked-By: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch performs the equivalent include directory shuffle for
plat-orion, and fixes up all users.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
They need to be exported, so let's give them less generic-sounding names
while we're at it.
Original export patch, along with the suggestion about the nomenclature,
from Stephen Rothwell.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This adds a WRITE_VERIFY Kconfig option to the DataFlash driver,
closely mirroring the similar NAND and ONENAND options, giving
an option to disable some code that's currently always enabled.
Removing this step probably saves a millisecond or so per page
when writing data, which will add up quickly since these pages
are small (the largest is 1 KiB). It doesn't seem to add a
lot in terms of reliability, and wouldn't detect errors which
crop up when transferring data to the on-chip SRAM buffer.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
> > linux-next-20080805/drivers/mtd/devices/mtd_dataflash.c: In function 'add_dataflash_otp':
> > linux-next-20080805/drivers/mtd/devices/mtd_dataflash.c:670: error: too many arguments to function 'otp_setup'
Whoops, sorry ... I see what was going on. My bad.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Timeouts are currently given by the typical operation time times 8.
It works in the general well-behaved case but not when an erase block is
failing. For erase operations, it seems that a failing erase block will
keep the device state machine in erasing state until the vendor
specified maximum timeout period has passed. By this time the driver
would have long since timed out, left erasing state and attempted
further operations which all fail. This patch implements timeouts using
values from the CFI Query structure when available.
The patch also sets a longer timeout for locking operations. The current
value used for locking/unlocking given by 1000000/HZ microseconds is too
short for devices like J3 and J5 Strataflash which have a typical clear
lock-bits time of 0.5 seconds.
Signed-off-by: Anders Grafström <grfstrm@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There are some CFI chips which require non standard procedures to get
into QRY mode. The possible way to support them would be trying
different modes till QRY will be read. This patch introduce two new
functions qry_mode_on qry_mode_off. qry_mode_on tries different commands
in order switch chip into QRY mode.
So if we have one more "odd" chip - we just could add several lines to
qry_mode_on. Also using these functions remove unnecessary code
duplicaton in porbe procedure.
Currently there are two "odd" cases
1. Some old intel chips which require 0xFF before 0x98
2. ST M29DW chip which requires 0x98 to be sent at 0x555 (according to
CFI should be 0x55)
This patch is partialy based on the patch from Uwe
(see "[PATCH 2/4] [RFC][MTD] cfi_probe: remove Intel chip workaround"
thread )
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: Alexander Belyakov <abelyako@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This long overdue trivial change to the MTD_CFI_AMDSTD kconfig menu
description is intended to help clarify that this option also supports
Spansion flash devices.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This was a reference board for which support never got merged upstream.
Kill it off, at rmk's suggestion.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
No file should be explicitly referencing its own platform headers
by specifying an absolute include path. Fix these paths to use
standard <asm/arch/...> includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As reported by Adrian Bunk, commit d5686b444f
(switch mtd and dm-table to lookup_bdev()) causes the following compile
error with CONFIG_BLOCK=n:
CC drivers/mtd/mtdsuper.o
drivers/mtd/mtdsuper.c: In function `get_sb_mtd':
drivers/mtd/mtdsuper.c:184: error: implicit declaration of function 'lookup_bdev'
drivers/mtd/mtdsuper.c:184: warning: assignment makes pointer from integer without a cast
drivers/mtd/mtdsuper.c:197: error: implicit declaration of function 'bdput'
make[3]: *** [drivers/mtd/mtdsuper.o] Error 1
Fix it by putting the block device lookup inside #ifdef CONFIG_BLOCK
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore
remove the dead code associated with !CONFIG_PPC_MERGE.
The mtd maps should be using the OF based mechanism.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Now that we can tell when we have one of the newer DataFlash chips,
optionally expose the 128 bytes of OTP memory they provide. Tested
on at45db642 revision B and D chips.
Switch mtdchar over to a generic HAVE_MTD_OTP flag instead of adding
another #ifdef for each type of chip whose driver has OTP support.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6:
[MTD] [NAND] drivers/mtd/nand/nandsim.c: fix printk warnings
[MTD] [NAND] Blackfin NFC Driver: Cleanup the error exit path of bf5xx_nand_probe function
[MTD] [NAND] Blackfin NFC Driver: use standard dev_err() rather than printk()
[MTD] [NAND] Blackfin NFC Driver: enable Blackfin nand HWECC support by default
[MTD] [NAND] Blackfin NFC Driver: add proper devinit/devexit markings to probe/remove functions
[MTD] [NAND] Blackfin NFC Driver: add support for the ECC layout the Blackfin bootrom uses
[MTD] [NAND] Blackfin NFC Driver: fix bug - hw ecc calc by making sure we extract 11 bits from each register instead of 10
[MTD] [NAND] Blackfin NFC Driver: fix bug - do not clobber the status from the first 256 bytes if operating on 512 pages
[MTD] [NAND] diskonchip.c fix sparse endian warnings
[MTD] [NAND] drivers/mtd/nand/nandsim.c needs div64.h
[JFFS2] Fix allocation of summary buffer
Fix rename of at91_nand -> atmel_nand
[MTD] [NOR] drivers/mtd/chips/jedec_probe.c: fix Am29DL800BB device ID
[MTD] MTD_DEBUG always does compile-time typechecks
[MTD] DataFlash: bugfix, binary page sizes now handled
[MTD] [NAND] fsl_elbc_nand.c: fix printk warning
[MTD] [NAND] nandsim: support random page read command
[MTD] [NAND] fix subpage read for small page NAND
