Registering Numark Party Mix II fails with error 'bogus bTerminalLink 1'.
The problem stems from the driver not being able to find input/output
terminals required to configure audio streaming. The information about
those terminals is stored in AudioControl Interface. Numark device
contains 2 AudioControl Interfaces and the driver checks only one of them.
According to the USB standard, a device can have multiple audio functions,
each represented by Audio Interface Collection. Every audio function is
considered to be closed box and will contain unique AudioControl Interface
and zero or more AudioStreaming and MIDIStreaming Interfaces.
The Numark device adheres to the standard and defines two audio functions:
- MIDIStreaming function
- AudioStreaming function
It starts with MIDI function, followed by the audio function. The driver
saves the first AudioControl Interface in `snd_usb_audio` structure
associated with the entire device. It then attempts to use this interface
to query for terminals and clocks. However, this fails because the correct
information is stored in the second AudioControl Interface, defined in the
second Audio Interface Collection.
This patch introduces a structure holding association between each
MIDI/Audio Interface and its corresponding AudioControl Interface,
instead of relying on AudioControl Interface defined for the entire
device. This structure is populated during usb probing phase and leveraged
later when querying for terminals and when sending USB requests.
Alternative solutions considered include:
- defining a quirk for Numark where the order of interface is manually
changed, or terminals are hardcoded in the driver. This solution would
have fixed only this model, though it seems that device is USB compliant,
and it also seems that other devices from this company may be affected.
What's more, it looks like products from other manufacturers have similar
problems, i.e. Rane One DJ console
- keeping a list of all AudioControl Interfaces and querying all of them
to find required information. That would have solved my problem and have
low probability of breaking other devices, as we would always start with
the same logic of querying first AudioControl Interface. This solution
would not have followed the standard though.
This patch preserves the `snd_usb_audio.ctrl_intf` variable, which holds
the first AudioControl Interface, and uses it as a fallback when some
interfaces are not parsed correctly and lack an associated AudioControl
Interface, i.e., when configured via quirks.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217865
Signed-off-by: Karol Kosik <k.kosik@outlook.com>
Link: https://patch.msgid.link/AS8P190MB1285893F4735C8B32AD3886BEC852@AS8P190MB1285.EURP190.PROD.OUTLOOK.COM
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For devices with multiple clock sources connected to a selector, we need
to check what a clock selector control request has returned. This is
needed to ensure that a requested clock source is indeed selected and for
autoclock feature to work.
For devices with single clock source connected, if we get an error there
is nothing else we can do about it. We can't skip clock selector setup as
it is required by some devices. So lets just ignore error in this case.
This should fix various buggy Mackie devices:
[ 649.109785] usb 1-1.3: parse_audio_format_rates_v2v3(): unable to find clock source (clock -32)
[ 649.111946] usb 1-1.3: parse_audio_format_rates_v2v3(): unable to find clock source (clock -32)
[ 649.113822] usb 1-1.3: parse_audio_format_rates_v2v3(): unable to find clock source (clock -32)
There is also interesting info from the Windows documentation [1] (this
is probably why manufacturers dont't even test this feature):
"The USB Audio 2.0 driver doesn't support clock selection. The driver
uses the Clock Source Entity, which is selected by default and never
issues a Clock Selector Control SET CUR request."
Link: https://learn.microsoft.com/en-us/windows-hardware/drivers/audio/usb-2-0-audio-drivers [1]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217314
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218175
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218342
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Link: https://lore.kernel.org/r/20240201115308.17838-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 67794f882a.
We need to explicitly set up the clock selector to workaround a problem
with the Behringer mixers. This was originally done in d2e8f64125
("ALSA: usb-audio: Explicitly set up the clock selector")
The problem with MOTU M Series mentioned in commit message was fixed in
a different way by checking control capabilities of clock selectors.
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Link: https://lore.kernel.org/r/20240128132338.819273-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clock selector control might be read-only. Add corresponding checks
to prevent sending control requests that would fail.
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Link: https://lore.kernel.org/r/20240125205457.28258-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since commit 086b957cc1 ("ALSA: usb-audio: Skip the clock selector
inquiry for single connections") we are already skipping clock selector
inquiry if only one clock source is connected, but we are still sending
a set request. Lets skip that too.
This should fix errors when setting a sample rate on devices that don't
have any controls present within the clock selector. An example of such
device is the new revision of MOTU M Series (07fd:000b):
AudioControl Interface Descriptor:
bLength 8
bDescriptorType 36
bDescriptorSubtype 11 (CLOCK_SELECTOR)
bClockID 1
bNrInPins 1
baCSourceID(0) 2
bmControls 0x00
iClockSelector 0
Perhaps we also should check if clock selectors are readable and writeable
like we already do for clock sources, but this is out of scope of this
patch.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217601
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Link: https://lore.kernel.org/r/20240123134635.54026-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Maris found out that the quirk for TEAC devices to work around the
clock setup is needed to apply only when the base clock is changed,
e.g. from 48000-based clocks (48000, 96000, 192000, 384000) to
44100-based clocks (44100, 88200, 176400, 352800), or vice versa,
while switching to another clock with the same base clock doesn't need
the (forcible) interface setup.
This patch implements the optimization for the TEAC clock quirk to
avoid the unnecessary interface re-setup.
Fixes: 5ce0b06ae5 ("ALSA: usb-audio: Workaround for clock setup on TEAC devices")
Reported-by: Maris Abele <maris7abele@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220531130749.30357-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Maris reported that TEAC UD-501 (0644:8043) doesn't work with the
typical "clock source 41 is not valid, cannot use" errors on the
recent kernels. The currently known workaround so far is to restore
(partially) what we've done unconditionally at the clock setup;
namely, re-setup the USB interface immediately after the clock is
changed. This patch re-introduces the behavior conditionally for TEAC
devices.
Further notes:
- The USB interface shall be set later in
snd_usb_endpoint_configure(), but this seems to be too late.
- Even calling usb_set_interface() right after
sne_usb_init_sample_rate() doesn't help; so this must be related
with the clock validation, too.
- The device may still spew the "clock source 41 is not valid" error
at the first clock setup. This seems happening at the very first
try of clock setup, but it disappears at later attempts.
The error is likely harmless because the driver retries the clock
setup (such an error is more or less expected on some devices).
Fixes: bf6313a0ff ("ALSA: usb-audio: Refactor endpoint management")
Reported-and-tested-by: Maris Abele <maris7abele@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220521064627.29292-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pointer cs_desc return from snd_usb_find_clock_source could
be null, so there is a potential null pointer dereference issue.
Fix this by adding a null check before dereference.
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Link: https://lore.kernel.org/r/20211024111736.11342-1-cyeaa@connect.ust.hk
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_usb_find_clock_source and snd_usb_find_clock_selector are helper
macros that look at an entity id and validate that this entity id is
in fact a clock source or a clock selector. The present comments
inside __uac_clock_find_source give the reader the impression we're
looking for an entity id.
We're looking for an entity id indeed, the clock source, but since
__uac_clock_find_source is recursive, we're also looking *at* the
entity ids, in the search for the one clock source.
Fix the comment so we don't give readers a wrong idea.
Signed-off-by: Geraldo Nascimento <geraldogabriel@gmail.com>
Link: https://lore.kernel.org/r/YU6Kj05oOqRmhJDf@geday
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As more and more device-specific workarounds came up and gathered in
various places, it becomes harder to manage. Now it's time to clean
up and collect workarounds more consistently and make them more easily
applicable.
This patch is the first step for that: a new field quirk_flags is
introduced in snd_usb_audio struct to contain the bit flags for
various device-specific quirks. Those are separate one from the
quirks in quirks-table.h; the quirks-table.h entries are for more
intrusive stuff that needs the descriptor override, while the new
quirk_flags is for easier ones that are tied with the vendor:product
IDs.
In this patch, as the first example, we convert the list of devices
and vendors to ignore GET_SAMPLE_RATE, formerly defined in
snb_usb_get_sample_rate_quirk().
Link: https://lore.kernel.org/r/20210729073855.19043-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The following scenario describes an echo test for
Samsung USBC Headset (AKG) with VID/PID (0x04e8/0xa051).
We first start a capture stream(USB IN transfer) in 96Khz/24bit/1ch mode.
In clock find source function, we get value 0x2 for clock selector
and 0x1 for clock source.
Kernel-4.14 behavior
Since clock source is valid so clock selector was not set again.
We pass through this function and start a playback stream(USB OUT transfer)
in 48Khz/32bit/2ch mode. This time we get value 0x1 for clock selector
and 0x1 for clock source. Finally clock id with this setting is 0x9.
Kernel-5.10 behavior
Clock selector was always set one more time even it is valid.
When we start a playback stream, we will get 0x2 for clock selector
and 0x1 for clock source. In this case clock id becomes 0xA.
This is an incorrect clock source setting and results in severe noises.
We see wrong data rate in USB IN transfer.
(From 288 bytes/ms becomes 144 bytes/ms) It should keep in 288 bytes/ms.
This earphone works fine on older kernel version load because
this is a newly-added behavior.
Fixes: d2e8f64125 ("ALSA: usb-audio: Explicitly set up the clock selector")
Signed-off-by: chihhao.chen <chihhao.chen@mediatek.com>
Link: https://lore.kernel.org/r/1627100621-19225-1-git-send-email-chihhao.chen@mediatek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This provides support for Denon DN-X1600 hardware mixer.
The device itself supports 44100, 48000 and 96000 (Hz)
sample rates, but switching rates via software is currently not working.
Therefore, this patch hardcodes the sample rate to 48000Hz which
enables all 8 channels to function correctly when the correct
sample rate is selected on the hardware itself.
MIDI also tested and works.
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Tested-by: xalmoxis@gmail.com
Link: https://lore.kernel.org/r/20210610083528.603942-2-damien@zamaudio.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The cur variable indicating the currently selected clock source can be
theoretically used as uninitialized after the recent commit
481f17c418 ("ALSA: usb-audio: Handle error for the current selector
gracefully"). For addressing it, initialize it before use.
Also, one place seems setting 0 to a wrong variable ret, instead of
cur; otherwise it makes little sense. Since the initialization is
done beforehand, we can get rid of this line, too.
Fixes: 481f17c418 ("ALSA: usb-audio: Handle error for the current selector gracefully")
Reported-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/4b261d68-f53f-240d-2d8a-2f88b337849d@canonical.com
Link: https://lore.kernel.org/r/s5hfsyhh97t.wl-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently we bail out when the device returns an error or an invalid
value for the current clock selector value via
uac_clock_selector_get_val(). But it's possible that the device is
really uninitialized and waits for the setup of the proper route at
first.
For handling such a case, this patch lets the driver dealing with the
error or the invalid error more gracefully, choosing the clock source
automatically instead.
Link: https://lore.kernel.org/r/20210518152112.8016-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch just does refactoring of the UAC2/3 clock setup code.
There should be no functional changes. The major changes are:
* Provide union objects for pointing both UAC2 and UAC3 objects
* Unify clock source, selector and multiplier helper functions
* Unify __uac_clock_find_source() to deal with both UAC2 and UAC3
equally
Link: https://lore.kernel.org/r/20210518152112.8016-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current code, we have some assumption that the audio clock
selector has been set up implicitly and don't want to touch it unless
it's really needed for the fallback autoclock setup. This works for
most devices but some seem having a problem. Partially this was
covered for the devices with a single connector at the initialization
phase (commit 086b957cc1 "ALSA: usb-audio: Skip the clock selector
inquiry for single connections"), but also there are cases where the
wrong clock set up is kept silently. The latter seems to be the cause
of the noises on Behringer devices.
In this patch, we explicitly set up the audio clock selector whenever
the appropriate node is found.
Reported-by: Geraldo Nascimento <geraldogabriel@gmail.com>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199327
Link: https://lore.kernel.org/r/CAEsQvcvF7LnO8PxyyCxuRCx=7jNeSCvFAd-+dE0g_rd1rOxxdw@mail.gmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210413084152.32325-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 93db51d06b ("ALSA: usb-audio: Check valid altsetting at
parsing rates for UAC2/3") changed the behavior of the function
set_sample_rate_v2v3() slightly to treat the inconsistent sample rate
as an error. It was done by assumption that the sample rate
validation should have been done at the parser phase as implemented in
that patch. But the validation is later selectively enabled only for
certain devices as it causes a regression (the commit fe773b8711
"ALSA: usb-audio: workaround for iface reset issue"), and now the
inconsistency surfaced as a fatal error while it worked in the past as
is, as reported for FiiO M3K DAC.
For recovering from the regression, change set_sample_rate_v2v3()
again to ignore the sample rate difference as non-error.
BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1182633
Fixes: 93db51d06b ("ALSA: usb-audio: Check valid altsetting at parsing rates for UAC2/3")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210227082002.21185-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current USB-audio driver gets an error at probing NUX MG-300 about
parsing the clocks. This is because the firmware doesn't return the
proper connection of the clock selector that is connected to a single
clock; it's likely that the firmware was lazy^w optimized and the
inquiry wasn't handled. Actually it makes little sense to inquire and
set up the single connection explicitly.
This patch fixes the issue by simply skipping the clock selector
inquiry if it's a single connection.
Reported-by: Mike Oliphant <oliphant@nostatic.org>
Link: https://lore.kernel.org/r/20210120213932.1971-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current sample rate setup function for UAC1 assumes only the first
endpoint retrieved from the interface:altset pair, but the rate set up
may be needed also for the secondary endpoint. Also, retrieving the
endpoint number from the interface descriptor is redundant; we have
already the target endpoint in the given audioformat object.
This patch simplifies the code and corrects the target endpoint as
described in the above. It simply refers to fmt->endpoint directly.
Also, this patch drops the pioneer_djm_set_format_quirk() that is
caleld from snd_usb_set_format_quirk(); this function does the sample
rate setup but for the capture endpoint (0x82), and that's exactly
what the change above fixes.
Link: https://lore.kernel.org/r/20210118075816.25068-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some buggy firmware don't give the current sample rate but leaves
zero. Handle this case more gracefully without warning but just skip
the current rate verification from the next time.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201218145858.2357-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The audioformat is referred in many places but most of usages are
read-only. Let's add const prefix in the possible places.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-28-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is an intensive surgery for the endpoint and stream management
for achieving more robust and clean code.
The goals of this patch are:
- More clear endpoint resource changes
- The interface altsetting control in a single place
Below are brief description of the whole changes.
First off, most of the endpoint operations are moved into endpoint.c,
so that the snd_usb_endpoint object is only referred in other places.
The endpoint object is acquired and released via the new functions
snd_usb_endpoint_open() and snd_usb_endpoint_close() that are called
at PCM hw_params and hw_free callbacks, respectively. Those are
ref-counted and EPs can manage the multiple opens.
The open callback receives the audioformat and hw_params arguments,
and those are used for initializing the EP parameters; especially the
endpoint, interface and altset numbers are read from there, as well as
the PCM parameters like the format, rate and channels. Those are
stored in snd_usb_endpoint object. If it's the secondary open, the
function checks whether the given parameters are compatible with the
already opened EP setup, too.
The coupling with a sync EP (including an implicit feedback sync) is
done by the sole snd_usb_endpoint_set_sync() call.
The configuration of each endpoint is done in a single shot via
snd_usb_endpoint_configure() call. This is the place where most of
PCM configurations are done. A few flags and special handling in the
snd_usb_substream are dropped along with this change.
A significant difference wrt the configuration from the previous code
is the order of USB host interface setups. Now the interface is
always disabled at beginning and (re-)enabled at the last step of
snd_usb_endpoint_configure(), in order to be compliant with the
standard UAC2/3. For UAC1, the interface is set before the parameter
setups since there seem devices that require it (e.g. Yamaha THR10),
just like how it was done in the previous driver code.
The start/stop are almost same as before, also single-shots. The URB
callbacks need to be set via snd_usb_endpoint_set_callback() like the
previous code at the trigger phase, too.
Finally, the flag for the re-setup is set at the device suspend
through the full EP list, instead of PCM trigger. This catches the
overlooked cases where the PCM hasn't been running yet but the device
needs the full setup after resume.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-26-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A preliminary change for the later big changes. This is a minor code
refactoring to drop the unnecessary arguments that can be retrieved in
a different way.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-20-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A preliminary patch for the later big change. Just a minor code
refactoring.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-19-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current driver code assumes blindly that all found sample rates for
the same endpoint from the UAC2 and UAC3 descriptors can be used no
matter which altsetting, but actually this was wrong: some devices
accept only limited sample rates in each altsetting. For determining
which altsetting supports which rate, we need to verify each sample rate
and check the validity via UAC2_AS_VAL_ALT_SETTINGS. This control
reports back the available altsettings as a bitmap.
This patch implements the missing piece above, the verification and
reconstructs the sample rate tables based on the result.
An open question is how to deal with the altsettings that ended up
with no valid sample rates after verification. At least, there is a
device that showed this problem although the sample rates did work in
the later usage (see bug link). For now, we accept such an altset as
is, assuming that it's a firmware bug.
Reported-by: Dylan Robinson <dylan_robinson@motu.com>
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1178203
Link: https://lore.kernel.org/r/20201123085347.19667-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MicroBook IIc operates in UAC2 mode by default. This patch addresses
several issues with it:
- MicroBook II and IIc shares the same USB ID. We can distinguish them
by interface class.
- MaxPacketsOnly attribute is erroneously set in endpoint descriptors.
As a result this card produces noise with all sample rates other than
96 KHz. This also causes issues like IOMMU page faults and other
problems with host controller.
- Sample rate changes takes more than 2 seconds for this device. Clock
validity request returns false during that period, so the clock validity
quirk is required.
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Link: https://lore.kernel.org/r/20200229151815.14199-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It should be safe to ignore clock validity check result if the following
conditions are met:
- only one single sample rate is supported;
- the terminal is directly connected to the clock source;
- the clock type is internal.
This is to deal with some Denon DJ controllers that always reports that
clock is invalid.
Tested-by: Tobias Oszlanyi <toszlanyi@yahoo.de>
Signed-off-by: Alexander Tsoy <alexander@tsoy.me>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200212235450.697348-1-alexander@tsoy.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use true/false for bool type return in uac_clock_source_is_valid().
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Link: https://lore.kernel.org/r/20191029175200.GA7320@saurav
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that we got the more comprehensive validation code for USB-audio
descriptors, the check of overflow in each descriptor unit parser
became superfluous. Drop some of the obvious cases.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the audio device is externally clocked and set to a rate that does
not match the external clock, the clock will never be valid and we cannot
set the rate successfully. To fix this, allow a rate change even if
the clock is initially invalid, and validate again after the rate is
changed.
This fixes problems with MOTU UltraLite AVB hardware over USB.
Signed-off-by: Adam Goode <agoode@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Avoid if ((err = ...) style and expand to multiple lines instead.
No change in the end result, but just the beautification.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently released USB Audio Class 3.0 specification
contains BADD (Basic Audio Device Definition) document
which describes pre-defined UAC3 configurations.
BADD support is mandatory for UAC3 devices, it should be
implemented as a separate USB device configuration.
As per BADD document, class-specific descriptors
shall not be included in the Device’s Configuration
descriptor ("inferred"), but host can guess them
from BADD profile number, number of endpoints and
their max packed sizes.
This patch adds support of all BADD profiles from the spec
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Tested-by: Jorge Sanjuan <jorge.sanjuan@codethink.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The UAC3 clock parser codes lack of the sanity checks for malformed
descriptors like UAC2 parser does. Without it, the driver may lead to
a potential crash.
Fixes: 9a2fe9b801 ("ALSA: usb: initial USB Audio Device Class 3.0 support")
Tested-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Reviewed-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The sanity checks introduced for malformed descriptors loosely check
the given descriptor size, although the size greater than the defined
description is invalid. It was due to a concern of any funky firmware
in the actual products. But this doesn't look hitting, and any sane
products must have the defined descriptors.
So in this patch, we make the validators more strict, allowing only
with the defined descriptor sizes. The value in clock selector
validator is corrected from 5 to 7 to count the two unlisted fields
after baCSourceID[].
Suggested-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Reviewed-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are lots of open-coded functions to find a clock source,
selector and multiplier. Now there are both v2 and v3, so six
variants.
This patch refactors the code to use a common helper for the main
loop, and define each validator function for each target.
There is no functional change.
Fixes: 9a2fe9b801 ("ALSA: usb: initial USB Audio Device Class 3.0 support")
Reviewed-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes code readability and should have no functional change.
Correct uac control query functions to account for the 1-based indexing
of USB Audio Class control identifiers.
The function parameter, u8 control, should be the
constant defined in audio-v2.h to identify the control to be checked for
readability or writeability.
This patch fixes all callers that had adjusted, and makes explicit
the mapping between audio_feature_info[] array index and the associated
control identifier.
Signed-off-by: Andrew Chant <achant@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently released USB Audio Class 3.0 specification
introduces many significant changes comparing to
previous versions, like
- new Power Domains, support for LPM/L1
- new Cluster descriptor
- changed layout of all class-specific descriptors
- new High Capability descriptors
- New class-specific String descriptors
- new and removed units
- additional sources for interrupts
- removed Type II Audio Data Formats
- ... and many other things (check spec)
It also provides backward compatibility through
multiple configurations, as well as requires
mandatory support for BADD (Basic Audio Device
Definition) on each ADC3.0 compliant device
This patch adds initial support of UAC3 specification
that is enough for Generic I/O Profile (BAOF, BAIF)
device support from BADD document.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The helper functions to parse and look for the clock source, selector
and multiplier unit may return the descriptor with a too short length
than required, while there is no sanity check in the caller side.
Add some sanity checks in the parsers, at least, to guarantee the
given descriptor size, for avoiding the potential crashes.
Fixes: 79f920fbff ("ALSA: usb-audio: parse clock topology of UAC2 devices")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are many USB audio devices with buggy firmware that don't react
with the sample rate reading properly. This often results in the
flood of error messages and slowing down the operation.
The sample rate read back is basically only for confirming the sample
rate setup, and it's not critically important. As a compromise, in
this patch, we stop the sample rate read back once when the device
gives errors more than tolerance (twice, as of now). This should
improve most of error cases while we still can catch the firmware
bugginess.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add some sanity check codes before actually accessing the endpoint via
get_endpoint() in order to avoid the invalid access through a
malformed USB descriptor. Mostly just checking bNumEndpoints, but in
one place (snd_microii_spdif_default_get()), the validity of iface and
altsetting index is checked as well.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=971125
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adds a quirk to disable the check that the sample rate has been set correctly, as the Lifecam does not support getting the sample rate.
This means that we don't need to wait for the USB timeout when attempting to get the sample rate. Waiting for the timeout causes problems in some applications, which give up on the device acquisition process before it has had time to complete, resulting in no sound.
[minor tidy up by tiwai]
Signed-off-by: Joe Turner <joe@oampo.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert with dev_err() and co from snd_printk(), etc.
As there are too deep indirections (e.g. ep->chip->dev->dev),
a few new local macros, usb_audio_err() & co, are introduced.
Also, the device numbers in some messages are dropped, as they are
shown in the prefix automatically.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of reading bInterfaceProtocol from the descriptor whenever it's
needed, store this value in the audioformat structure. Besides
simplifying some code, this will allow us to correctly handle vendor-
specific devices where the descriptors are marked with other values.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
The Scarlett 2i2 seems to take almost 500 ms to set the sample rate,
even if the clock is currently set to that value. This patch speeds
up prepare of the device, by avoiding setting the clock to something
it already is.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It turns out the devices from Playback Design need the delay quirk
after usb_set_interface from clocks.c as well. Make it a proper
quirks function and factor out the code to quirks.c.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some clocks might be read-only, e.g., external clocks (see also
UAC2 4.7.2.1).
In this case, setting the sample frequency will always fail
(even if the rate is equal to the current clock rate),
therefore do not write, but read the value and compare to the
requested rate.
If the clock is read only, avoid reading it twice.
If it doesn't match, return -ENXIO since the clock is invalid for
this configuration.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Show the error code returned from the USB subsystem in
the debug messages.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
