gpio_get() should return DATAIN register value when the GPIO
is configured as input whereas it should return DATAOUT register
value when the GPIO is configured as output.
Now /sys/kernel/debug/gpio shows proper values for output GPIOs
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eliminates this compiler warning:
arch/powerpc/kvm/../../../virt/kvm/kvm_main.c:1178: error: integer overflow in expression
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Avi Kivity <avi@redhat.com>
There are two waitqueues in kvm for wait handling:
vcpu->wq for virt/kvm/kvm_main.c and
vpcu->arch.local_int.wq for the s390 specific wait code.
the wait handling in kvm_s390_handle_wait was broken by using different
wait_queues for add_wait queue and remove_wait_queue.
There are two options to fix the problem:
o move all the s390 specific code to vcpu->wq and remove
vcpu->arch.local_int.wq
o move all the s390 specific code to vcpu->arch.local_int.wq
This patch chooses the 2nd variant for two reasons:
o s390 does not use kvm_vcpu_block but implements its own enabled wait
handling.
Having a separate wait_queue make it clear, that our wait mechanism is
different
o the patch is much smaller
Report-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We have to disable preemption and IRQs on every exit from
handle_invalid_guest_state, otherwise we generate at least a
preempt_disable imbalance.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Release and re-acquire preemption and IRQ lock in the same order as
vcpu_enter_guest does.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
kvm_mmu_change_mmu_pages mishandles the case where n_alloc_mmu_pages is
smaller then n_free_mmu_pages, by not checking if the result of
the subtraction is negative.
Its a valid condition which can happen if a large number of pages has
been recently freed.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If a migrated vcpu matches the asid_generation value of the target pcpu,
there will be no TLB flush via TLB_CONTROL_FLUSH_ALL_ASID.
The check for vcpu.cpu in pre_svm_run is meaningless since svm_vcpu_load
already updated it on schedule in.
Such vcpu will VMRUN with stale TLB entries.
Based on original patch from Joerg Roedel (http://patchwork.kernel.org/patch/10021/)
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Do not allow invalid memory types in MTRR/PAT (generating a #GP
otherwise).
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Fix division by zero triggered by latch count command on uninitialized
counter.
Cc: stable@kernel.org
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
So far, KVM copied the emulated_msrs (only MSR_IA32_MISC_ENABLE) to a
wrong address in user space due to broken pointer arithmetic. This
caused subtle corruption up there (missing MSR_IA32_MISC_ENABLE had
probably no practical relevance). Moreover, the size check for the
user-provided kvm_msr_list forgot about emulated MSRs.
Cc: stable@kernel.org
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
With CONFIG_STACK_PROTECTOR turned on, VMI doesn't boot with
more than one processor. The problem is with the gs value not
being initialized correctly when registering the secondary
processor for VMI's case.
The patch below initializes the gs value for the AP to
__KERNEL_STACK_CANARY. Without this the secondary processor
keeps on taking a GP on every gs access.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Cc: <stable@kernel.org> # for v2.6.30.x
LKML-Reference: <1249425262.18955.40.camel@ank32.eng.vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Work around compilation warning in arch/x86/kernel/apm_32.c
x86, UV: Complete IRQ interrupt migration in arch_enable_uv_irq()
x86, 32-bit: Fix double accounting in reserve_top_address()
x86: Don't use current_cpu_data in x2apic phys_pkg_id
x86, UV: Fix UV apic mode
x86, UV: Fix macros for accessing large node numbers
x86, UV: Delete mapping of MMR rangs mapped by BIOS
x86, UV: Handle missing blade-local memory correctly
x86: fix assembly constraints in native_save_fl()
x86, msr: execute on the correct CPU subset
x86: Fix assert syntax in vmlinux.lds.S
x86: Make 64-bit efi_ioremap use ioremap on MMIO regions
x86: Add quirk to make Apple MacBook5,2 use reboot=pci
x86: Fix CPA memtype reserving in the set_pages_array*() cases
x86, pat: Fix set_memory_wc related corruption
x86: fix section mismatch for i386 init code
The following fix was initially inspired by David Howells fix
few days back:
http://lkml.org/lkml/2009/7/9/109
However, Ingo disapproves such fixes as it's dangerous (it can
hide future, relevant warnings) - in something as
performance-uncritical.
So, initialize 'err' to '0' to work around a GCC false positive
warning:
http://lkml.org/lkml/2009/7/18/89
Signed-off-by: Subrata Modak<subrata@linux.vnet.ibm.com>
Cc: Sachin P Sant <sachinp@linux.vnet.ibm.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <20090721023226.31855.67236.sendpatchset@subratamodak.linux.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In uv_setup_irq(), the call to create_irq() initially assigns
IRQ vectors to cpu 0. The subsequent call to
assign_irq_vector() in arch_enable_uv_irq() migrates the IRQ to
another cpu and frees the cpu 0 vector - at least it will be
freed as soon as the "IRQ move" completes.
arch_enable_uv_irq() needs to send a cleanup IPI to complete
the IRQ move. Otherwise, assignment of GRU interrupts on large
systems (>200 cpus) will exhaust the cpu 0 interrupt vectors
and initialization of the GRU driver will fail.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090720142840.GA8885@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With VMALLOC_END included in the calculation of MAXMEM (as of
2.6.28) it is no longer correct to also bump __VMALLOC_RESERVE
in reserve_top_address(). Doing so results in needlessly small
lowmem.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <4A71DD2A020000780000D482@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Change SGI UV default apicid mode to "physical". This is
required to match settings in the UV hub chip.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090727143856.GA8905@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The UV chipset automatically supplies the upper bits on nodes
being referenced by MMR accesses. These bit can be deleted from
the hub addressing macros.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20090727143808.GA8076@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The UV BIOS has added additional MMR ranges that are mapped via
EFI virtual mode mappings. These ranges should be deleted from
ranges mapped by uv_system_init().
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: linux-mm@kvack.org
LKML-Reference: <20090727143656.GA7698@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
UV blades may not have any blade-local memory. Add a field
(nid) to the UV blade structure to indicates whether the node
has local memory. This is needed by the GRU driver (pushed
separately).
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: linux-mm@kvack.org
LKML-Reference: <20090727143507.GA7006@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
From Gabe Black in bugzilla 13888:
native_save_fl is implemented as follows:
11static inline unsigned long native_save_fl(void)
12{
13 unsigned long flags;
14
15 asm volatile("# __raw_save_flags\n\t"
16 "pushf ; pop %0"
17 : "=g" (flags)
18 : /* no input */
19 : "memory");
20
21 return flags;
22}
If gcc chooses to put flags on the stack, for instance because this is
inlined into a larger function with more register pressure, the offset
of the flags variable from the stack pointer will change when the
pushf is performed. gcc doesn't attempt to understand that fact, and
address used for pop will still be the same. It will write to
somewhere near flags on the stack but not actually into it and
overwrite some other value.
I saw this happen in the ide_device_add_all function when running in a
simulator I work on. I'm assuming that some quirk of how the simulated
hardware is set up caused the code path this is on to be executed when
it normally wouldn't.
A simple fix might be to change "=g" to "=r".
Reported-by: Gabe Black <spamforgabe@umich.edu>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Stable Team <stable@kernel.org>
Make rdmsr_on_cpus/wrmsr_on_cpus execute on the current CPU only if it
is in the supplied bitmask.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Older versions of binutils did not accept the naked "ASSERT" syntax;
it is considered an expression whose value needs to be assigned to
something.
Reported-tested-and-fixed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The latest Apple MacBook (MacBook5,2) doesn't reboot successfully
under Linux; neither the EFI reboot method nor the default method
using the keyboard controller works (the system just hangs and doesn't
reset). However, the method using the "PCI reset register" at 0xcf9
does work.
This adds a quirk to detect this machine via DMI and force the
reboot_type to BOOT_CF9. With this it reboots successfully without
requiring a command-line option. Note that the EFI code forces
reboot_type to BOOT_EFI when the machine is booted via EFI, but this
overrides that since the core_initcall runs after the EFI
initialization code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
LKML-Reference: <19062.56420.501516.316181@cargo.ozlabs.ibm.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The code was incorrectly reserving memtypes using the page
virtual address instead of the physical address. Furthermore,
the code was not ignoring highmem pages as it ought to.
( upstream does not pass in highmem pages yet - but upcoming
graphics code will do it and there's no reason to not handle
this properly in the CPA APIs.)
Fixes: http://bugzilla.kernel.org/show_bug.cgi?id=13884
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: <stable@kernel.org>
Cc: dri-devel@lists.sourceforge.net
Cc: venkatesh.pallipadi@intel.com
LKML-Reference: <1249284345-7654-1-git-send-email-thellstrom@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There were three different errors resulting in a "dangerous relocation"
message. Add the relocation type to the messgages to make them more
useful.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In mm/slab.c the function do_ccupdate_local requires that interrupts be
disabled. If they are not, we panic with CONFIG_DEBUG_SLAB.
So we disable interrupts while processing IPIs. Also these are not shared
irqs, so get rid of the IRQF_SHARED flag.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression x,__divisor;
@@
- (((x) + ((__divisor) / 2)) / (__divisor))
+ DIV_ROUND_CLOSEST(x,__divisor)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the following warning at boot time:
WARNING: at drivers/gpio/gpiolib.c:83 0x8021d5e0()
autorequest GPIO-207
Modules linked in:
Call Trace:[<8011e0ec>] 0x8011e0ec
[<80110a28>] 0x80110a28
[<80110a28>] 0x80110a28
[..snip..]
The current code does not request the GPIO and attempts
to set its direction, which is a violation of the GPIO API.
This patch also unhardcode the GPIO we request and use
the one we defined in the button driver.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that we have removed all warnings from the ar7 board code we can use
-Werror like on other MIPS boards.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the following build failure when CONFIG_SERIAL_8250
is not enabled in the kernel configuration:
arch/mips/ar7/built-in.o: In function 'ar7_register_devices':
platform.c:(.init.text+0x61c): undefined reference to 'early_serial_setup'
platform.c:(.init.text+0x61c): relocation truncated to fit: R_MIPS_26 against 'early_serial_setup'
platform.c:(.init.text+0x68c): undefined reference to 'early_serial_setup'
platform.c:(.init.text+0x68c): relocation truncated to fit: R_MIPS_26 against 'early_serial_setup'
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the following build warning:
arch/mips/ar7/memory.c: In function 'memsize':
arch/mips/ar7/memory.c:55: warning: passing argument 1 of 'writel' makes integer from pointer without a cast
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some SiliconImage PCIe SATA controlers are not detected when the bus
numbers differ.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current interrupt handling code for the MSP4200 always masks an
interrupt before acknowledging it. This is not required, as that will be
handled by the level interrupt handler. This change simplifies the MSP4200
code to remove the masking in the ack routine, and makes sure that the
minimum required operation is performed for masking and acking, rather
than always both masking and acking the interrupt.
Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Trying to build a PMC-Sierra MSP4200 VoIP gateway defconfig will not work
since MIPS34K_MISSED_ITLB_WAR is not defined for all boards supported
within pmc-serria/msp71xx. This patch defines MIPS34K_MISSED_ITLB_WAR to
prevent such build failures:
CHK include/linux/version.h
CHK include/linux/utsrelease.h
SYMLINK include/asm -> include/asm-mips
CC arch/mips/kernel/asm-offsets.s
In file included fromlinux-msp71xx/linux-2.6.29/arch/mips/include/asm/bitops.h:24,
from include/linux/bitops.h:17,
from include/linux/kernel.h:15,
from include/linux/sched.h:52,
from arch/mips/kernel/asm-offsets.c:13:
linux-msp71xx/linux-2.6.29/arch/mips/include/asm/war.h:241:2: error: #error Check setting of MIPS34K_MISSED_ITLB_WAR for your
platform
This fixes a compile error when building for the MSP4200 boards. Identical
patches to fix this were send by
Florian Fainelli <florian@openwrt.org>
Shane McDonald <mcdonald.shane@gmail.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Trying to build MSP4200 VoIP defconfig also fails on msp_irq_slp.c with a
non-existing reference to mask_slp_irq, which is in turn mask_msp_slp_irq.
Passed that, we will also miss a comma when calling
set_irq_chip_and_handler. This patch fixes both issues.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Shane McDonald <mcdonald.shane@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loading of modules with unresolved weak symbols fails on MIPS
since '88173507e4fc1e7ecd111b0565e8cba0cb7dae6d'.
Modules: handle symbols that have a zero value
The module subsystem cannot handle symbols that are zero. If symbols
are present that have a zero value then the module resolver prints out a
message that these symbols are unresolved.
We have to use IS_ERR_VALUE() to check that a symbol has been resolved
or not.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit fc03bc1715ca0ad4ccfe97aab16bcc9e7129c1a4 breaks when SMTC support
is enabled on Malta.
Signed-off-by: Raghu Gandham <raghu@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The resume() implementation octeon_switch.S examines the saved cp0_status
register. We were clobbering the entire pt_regs structure in kernel
threads leading to random crashes.
When switching away from a kernel thread, the saved cp0_status is examined
and if bit 30 is set it is cleared and the CP2 state saved into the pt_regs
structure. Since the kernel thread stack overlaid the pt_regs structure
this resulted in a corrupt stack. When the kthread with the corrupt stack
was resumed, it could crash if it used any of the data in the stack that was
clobbered.
We fix it by moving the kernel thread stack down so it doesn't overlay
pt_regs.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
cc1: warnings being treated as errors
arch/mips/mipssim/sim_time.c: In function 'get_c0_compare_int':
arch/mips/mipssim/sim_time.c:103: warning: ISO C90 forbids mixed declarations and code
arch/mips/mipssim/sim_time.c:116: error: expected declaration or statement at end of input
make[1]: *** [arch/mips/mipssim/sim_time.o] Error 1
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the pagefault oom path which does not drop mm->mmap_sem.
This was introduced by commit c7c1e3846b
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
They tend to get not updated when files are moved around or copied and
lack any obvious use. While at it zap some only too obvious comments and
as per Shinya's suggestion, add a copyright header to extable.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
SPI pins are now allocated in pcm037.c, remove them from EET.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Changeset 3869c4aa18
that went in after 2.6.30-rc1 was a seemingly small change to _set_memory_wc()
to make it complaint with SDM requirements. But, introduced a nasty bug, which
can result in crash and/or strange corruptions when set_memory_wc is used.
One such crash reported here
http://lkml.org/lkml/2009/7/30/94
Actually, that changeset introduced two bugs.
* change_page_attr_set() takes &addr as first argument and can the addr value
might have changed on return, even for single page change_page_attr_set()
call. That will make the second change_page_attr_set() in this routine
operate on unrelated addr, that can eventually cause strange corruptions
and bad page state crash.
* The second change_page_attr_set() call, before setting _PAGE_CACHE_WC, should
clear the earlier _PAGE_CACHE_UC_MINUS, as otherwise cache attribute will not
be WC (will be UC instead).
The patch below fixes both these problems. Sending a single patch to fix both
the problems, as the change is to the same line of code. The change to have a
addr_copy is not very clean. But, it is simpler than making more changes
through various routines in pageattr.c.
A huge thanks to Jerome for reporting this problem and providing a simple test
case that helped us root cause the problem.
Reported-by: Jerome Glisse <glisse@freedesktop.org>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20090730214319.GA1889@linux-os.sc.intel.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: at_hdmac: add DMA slave transfers
dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller
dmaengine: dmatest: correct thread_count while using multiple thread per channel
dmaengine: dmatest: add a maximum number of test iterations
drivers/dma: Remove unnecessary semicolons
drivers/dma/fsldma.c: Remove unnecessary semicolons
dmaengine: move HIGHMEM64G restriction to ASYNC_TX_DMA
fsldma: do not clear bandwidth control bits on the 83xx controller
fsldma: enable external start for the 83xx controller
fsldma: use PCI Read Multiple command
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Update defconfigs for embedded 6xx/7xxx, 8xx, 8{3,5,6}xxx
powerpc/86xx: Update GE Fanuc sbc310 default configuration
powerpc/86xx: Update defconfig for GE Fanuc's PPC9A
cpm_uart: Don't use alloc_bootmem in cpm_uart_cpm2.c
powerpc/83xx: Fix PCI IO base address on MPC837xE-RDB boards
powerpc/85xx: Don't scan for TBI PHY addresses on MPC8569E-MDS boards
powerpc/85xx: Fix ethernet link detection on MPC8569E-MDS boards
powerpc/mm: Fix SMP issue with MMU context handling code
The pwm hardware only checks the compare register after a decrement,
so the pin never toggles if tcmp = tcnt.
This happens when a very low duty cycle is requested. Fix it by always
ensuring that tcmp < tcnt.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make software reset to avoid freeze if PCI bus was messed up
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After ftrace_trace_function is called r1 is probably clobbered so don't
try to use its value for restoring.
This was introduced in v2.6.29~38^2~7
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Every so often, after code shuffles, I need to go through and unbitrot
the Lguest Journey (see drivers/lguest/README). Since we now use RCU in
a simple form in one place I took the opportunity to expand that explanation.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
I don't really notice it (except to begrudge the extra vertical
space), but Ingo does. And he pointed out that one excuse of lguest
is as a teaching tool, it should set a good example.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
General update of defconfig including the following notable changes:
- Enable Highmem support.
- Support for PCMCIA based daughter card.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
General update of defconfig including the following notable changes:
- Enable GPIO access via sysfs on GE Fanuc's PPC9A.
- Enable Highmem support.
- Support for PCMCIA based daughter card.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
U-Boot maps PCI IO at 0xe0300000, while current dts files specify
0xe2000000. This leads to the following oops with CONFIG_8139TOO_PIO=y.
8139too Fast Ethernet driver 0.9.28
Machine check in kernel mode.
Caused by (from SRR1=41000): Transfer error ack signal
Oops: Machine check, sig: 7 [#1]
MPC837x RDB
[...]
NIP [00000900] 0x900
LR [c0439df8] rtl8139_init_board+0x238/0x524
Call Trace:
[cf831d90] [c0439dcc] rtl8139_init_board+0x20c/0x524 (unreliable)
[cf831de0] [c043a15c] rtl8139_init_one+0x78/0x65c
[cf831e40] [c0235250] pci_call_probe+0x20/0x30
[...]
This patch fixes the issue by specifying the correct PCI IO base
address.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Sometimes (e.g. when there are no UEMs attached to a board)
fsl_pq_mdio_find_free() fails to find a spare address for a TBI PHY,
this is because get_phy_id() returns bogus 0x0000ffff values
(0xffffffff is expected), and therefore mdio bus probing fails with
the following message:
fsl-pq_mdio: probe of e0082120.mdio failed with error -16
And obviously ethernet doesn't work after this.
This patch solves the problem by adding tbi-phy node into mdio node,
so that we won't scan for spare addresses, we'll just use a fixed one.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Linux isn't able to detect link changes on ethernet ports that were
used by U-Boot. This is because U-Boot wrongly clears interrupt
polarity bit (INTPOL, 0x400) in the extended status register (EXT_SR,
0x1b) of Marvell PHYs.
There is no easy way for PHY drivers to know IRQ line polarity (we
could extract it from the device tree and pass it to phydevs, but
that'll be quite a lot of work), so for now just reset the PHYs to
their default states.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In switch_mmu_context() if we call steal_context_smp() to get a context
to use we shouldn't fall through and than call steal_context_up(). Doing
so can be problematic in that the 'mm' that steal_context_up() ends up
using will not get marked dirty in the stale_map[] for other CPUs that
might have used that mm. Thus we could end up with stale TLB entries in
the other CPUs that can cause all kinda of havoc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The value of armclk_mask needs to be inverted for use as a mask on
the register value when updating ARM_RATIO.
This is critical for cpufreq support, without it attempts to scale
the frequency of the core trash pretty much the entire clock tree.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
If the requested clock is faster than the parent clock then the
parent clock is the closest we can get to the request so we need
to return that instead of the requested clock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In the s3c_gpiolib_getchip implementation for s3c24xx the check whether a pin is
in the gpio banks range is reversed. Thus the function returns NULL for valid
pins and the gpio chip if its not valid.
As a result gpio states are not saved/restored properly during suspend/resume.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'drm-radeon-kms' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (35 commits)
drm/radeon: set fb aperture sizes for framebuffer handoff.
drm/ttm: fix highuser vs dma32 confusion.
drm/radeon: Fix size used for benchmarking BO copies.
drm/radeon: Add radeon.test parameter for running BO GPU copy tests.
drm/radeon/kms: allow interruptible waits for objects.
drm/ttm: powerpc: Fix Highmem cache flushing.
x86: Export kmap_atomic_prot() needed for TTM.
drm/ttm: Fix ttm in-kernel copying of pages with non-standard caching attributes.
drm/ttm: Fix an oops and sync object leak.
drm/radeon/kms: vram sizing on certain r100 chips needs workaround.
drm/radeon: Pay more attention to object placement requested by userspace.
drm/radeon: Fall back to evicting BOs with memcpy if necessary.
drm/radeon: Don't unreserve twice on failure to validate.
drm/radeon/kms: fix bandwidth computation on avivo hardware
drm/radeon/kms: add initial colortiling support.
drm/radeon/kms: fix hotspot handling on pre-avivo chips
drm/radeon/kms: enable frac fb divs on rs600/rs690/rs740
drm/radeon/kms: add PLL flag to prefer frequencies <= the target freq
drm/radeon/kms: block RN50 from using 3D engine.
drm/radeon/kms: fix VRAM sizing like DDX does it.
...
This functionality is needed to kmap_atomic() highmem pages that may
potentially have or are about to set up other mappings with
non-standard caching attributes.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- enable PCM043, MX31LILLY, ARMADILLO5X0 and MX35_3DS boards
- enable MXC nand driver
- enable UBI support
- disable cs89x0 support which broke all boards which do not have this chip
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The first thing sys_truncate() and sys_ftruncate() do is sign extend
the unsigned length arg to a signed type.
Thanks to Benjamin Herrenschmidt for the tip.
Signed-off-by: David S. Miller <davem@davemloft.net>
Those definitions are already provided by asm-generic
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Startup code for i386 in arch/x86/kernel/head_32.S is using the
reference variable initial_code that is located in the .cpuinit.data
section. If CONFIG_HOTPLUG_CPU is enabled, startup code is not in an
init section and can be called later too. In this case the reference
initial_code must be kept too. This patch fixes this. See below for
the section mismatch warning.
WARNING: vmlinux.o(.cpuinit.data+0x0): Section mismatch in reference
from the variable initial_code to the function
.init.text:i386_start_kernel()
The variable __cpuinitdata initial_code references
a function __init i386_start_kernel().
If i386_start_kernel is only used by initial_code then
annotate i386_start_kernel with a matching annotation.
Signed-off-by: Robert Richter <robert.richter@amd.com>
LKML-Reference: <1248716632-26844-1-git-send-email-robert.richter@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Makefile cleanup
microblaze: Typo fix for cpu param inconsistency
microblaze: Add support for R_MICROBLAZE_64_NONE
microblaze: Get module loading working
microblaze: remove sys_ipc
microblaze: Support unaligned address for put/get_user macros
microblaze: Detect new Microblaze 7.20 versions
microblaze: Fix do_page_fault for no context
microblaze: Add _PAGE_FILE macros to pgtable.h
microblaze: Fix put_user macro for 64bits arguments
microblaze: Clear print messages for DTB passing via r7
microblaze: Not to clear r7 after copying DTB to kernel
microblaze: Add messages about FDT blob
microblaze: Final support for statically linked DTB
microblaze: remove duplicated #include
microblaze: Define tlb_flush macro
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: geode: Mark mfgpt irq IRQF_TIMER to prevent resume failure
x86, amd: Don't probe for extended APIC ID if APICs are disabled
x86, mce: Rename incorrect macro name "CONFIG_X86_THRESHOLD"
x86-64: Fix bad_srat() to clear all state
x86, mce: Fix set_trigger() accessor
x86: Fix movq immediate operand constraints in uaccess.h
x86: Fix movq immediate operand constraints in uaccess_64.h
x86: Add reboot fixup for SBC-fitPC2
x86: Include all of .data.* sections in _edata on 64-bit
x86: Add quirk for Intel DG45ID board to avoid low memory corruption
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] zcrypt: fix scheduling of hrtimer ap_poll_timer
[S390] vdso: clock_gettime of CLOCK_THREAD_CPUTIME_ID with noexec=on
[S390] vdso: fix per cpu area allocation
[S390] hibernation: fix register corruption on machine checks
[S390] hibernation: fix lowcore handling
mm: Pass virtual address to [__]p{te,ud,md}_free_tlb()
Upcoming paches to support the new 64-bit "BookE" powerpc architecture
will need to have the virtual address corresponding to PTE page when
freeing it, due to the way the HW table walker works.
Basically, the TLB can be loaded with "large" pages that cover the whole
virtual space (well, sort-of, half of it actually) represented by a PTE
page, and which contain an "indirect" bit indicating that this TLB entry
RPN points to an array of PTEs from which the TLB can then create direct
entries. Thus, in order to invalidate those when PTE pages are deleted,
we need the virtual address to pass to tlbilx or tlbivax instructions.
The old trick of sticking it somewhere in the PTE page struct page sucks
too much, the address is almost readily available in all call sites and
almost everybody implemets these as macros, so we may as well add the
argument everywhere. I added it to the pmd and pud variants for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Howells <dhowells@redhat.com> [MN10300 & FRV]
Acked-by: Nick Piggin <npiggin@suse.de>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
correct GPIO freed in treo680_irda_shutdown()
Signed-off-by: Tomáš ?ech <sleep_walker@suse.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ezLCD+101 board (to which an favr-32 is fitted) has a long,
unshielded, nasty lead between the touch panel and the ads7843 touch
controller. In order to get satisfactory response then, we need to
employ every noise-reduction trick in the driver's arsenal. After
extensive fiddling I've found some good settings:
1) We keep vref on all the time to dramatically reduce settling times
(at the cost of a tiny increase in power consumption).
2) Despite 1 the settling time is still non-zero. 500uS is plenty of
time for the signals to settle
3) Despite 1 and 2 there's still a little bit of noise around. By
setting a pen recheck delay we make the panel feel less touchy and
twitchy.
Someone with more time and patience myself might be able to tune this
numbers further but these settings are now perfectly acceptable for
normal use.
Tested on ezLCD+101 though should only improve response on other ezLCD+/
favr-32 boards too.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
in case of memcpy(p, unaligned, 1..3) we get 1..3 as the
return value instead of p
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
memcpy(p, unaligned, 4..) returns (p + num_of_unaligned_by_copied)
instead of p because p is not preserved in the unaligned case.
Noticed by Herbert Xu's superior parameter recycling coding technique
which let the md4 self-test fail on avr32.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Reviewed the Makefile on request by Michal and this is the resulting changes.
o Use ':=' for assignmnet so we do not re-evaluate for each use
o Use $(shell echo xxx) to remove ""
o Replaced CFLAGS_KERNEL with KBUILD_CFLAGS
The settings are equally relevant for modules and the linked kernel
o Dropped LDFLAGS_BLOB - it is no longer used
o Refactored assignmnets to libs-y and core-y
o Use MMU for the MMU specific extension. "MMUEXT" was hurting my eyes
and I did not wanted it spread to m68k
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Michal Simek <monstr@monstr.eu>
New reloc type R_MICROBLAZE_32_PCREL_LO requires a null handler (no work to do).
Remove legacy hack for broken linker pre gcc-4.1.1, that required us to extract
an offset from the code, add it to the addend, then rewrite the instruction.
Fixup the invalid reloc type error output.
Boot tested with the xilinx_emaclite ethernet driver.
Signed-off-by: John Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
The ipc system call is now unused in microblaze,
as the system call table points directly to the
indidual system calls for IPC.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michal Simek <monstr@monstr.eu>
This patch add support for cases where load/store instruction
in put/get_user macro gets unaligned pointer to data and this
address is not valid. I prevent all cases which can failed.
I had to disable first stage of unaligned handler which is used
only for noMMU kernel and the whole work is done when interrupt
is enabled.
You have enable HW support for detect unaligned access in Microblaze.
This patch fixed three LTP tests:
getpeername01, getsockname01, socketpair01
Signed-off-by: Michal Simek <monstr@monstr.eu>
Calling fixup when we are in kernel mode. This
prevent fault for copy_to/from_user. This fault
was find thanks to writev01/03/04 LTP tests.
Signed-off-by: Michal Simek <monstr@monstr.eu>
We need to define _PAGE_FILE macro and change pte
functions. Microblaze use the same MMU as PowerPC
that's why we define _PAGE_FILE in the same style.
This change fixed remap_file_pages01 LTP test.
Signed-off-by: Michal Simek <monstr@monstr.eu>
For 64bits arguments gcc caused that put_user macro
works with wrong value because of optimalization.
Adding volatile caused that gcc not optimized it.
It is possible to use (as Blackfin do) two put_user
macros with 32bits arguments but there is one more
instruction which is due to duplication zero return
value which is called put_user_asm macro.
Signed-off-by: Michal Simek <monstr@monstr.eu>
It is necessary to zeroed r7 when r7 points to bad
dtb - this caused that we have correct messages
about compiled-in dtb or passing via r7
Signed-off-by: Michal Simek <monstr@monstr.eu>
If r7 is zero at kernel boot, or does not point to a valid DTB, then
we fall back to a DTB (assumed to be) linked statically in the kernel, instead
of blindly copying bogus cruft into the kernel DTB memory region
Signed-off-by: John Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
This fix remove bug which we had till now in all
Microblaze MMU code. Primary tested on mmap01 LTP test.
We forget to flush invalid tlb which were changed - we
used them and there were wrong old data which wasn't correct.
Signed-off-by: Michal Simek <monstr@monstr.eu>
fix the following 'make includecheck' warning:
arch/arm/plat-stmp3xxx/pinmux.c: linux/sysdev.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: dmitry pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/plat-s3c64xx/pm.c: plat/regs-gpio.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-omap2/mcbsp.c: mach/irqs.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-omap1/mcbsp.c: mach/irqs.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-sffsdr.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm646x-evm.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm644x-evm.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm355-leopard.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/mach-davinci/board-dm355-evm.c: mach/common.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/include/asm/atomic.h: asm/system.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
fix the following 'make includecheck' warning:
arch/arm/boot/compressed/misc.c: linux/compiler.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix two bugs in the OMAP3 clock tree pertaining to the SSI, DSS,
USBHOST, and HSOTGUSB devices. These devices are both interconnect
initiators and targets. Without this patch, clk_enable()s on clocks for
these modules can be very high latency (potentially up to ~200
milliseconds) and message such as the following are generated:
Clock usbhost_48m_fck didn't enable in 100000 tries
Two bugs are fixed by this patch. First, OMAP hardware only supports
target CM_IDLEST register bits on ES2+ chips and beyond. ES1 chips
should not wait for these clocks to enable. So, split the appropriate
clocks into ES1 and ES2+ variants, so that kernels running on ES1
devices won't try to wait.
Second, the current heuristic in omap2_clk_dflt_find_idlest() will
fail for these clocks. It assumes that the CM_IDLEST bit to wait upon
is the same as the CM_*CLKEN bit, which is false[1]. Fix by
implementing custom clkops .find_idlest function pointers for the
appropriate clocks that return the correct slave IDLEST bit shift.
This was originally fixed in the linux-omap kernel during 2.6.29 in a
slightly different manner[2][3].
In the medium-term future, all of the module IDLEST code will
eventually be moved to the omap_hwmod code.
Problem reported by Jarkko Nikula <jhnikula@gmail.com>:
http://marc.info/?l=linux-omap&m=124306184903679&w=2
...
1. See for example 34xx TRM Revision P Table 4-213 and 4-217 (for the
DSS case).
2. http://www.spinics.net/lists/linux-omap/msg05512.html et seq.
3. http://lkml.indiana.edu/hypermail/linux/kernel/0901.3/01498.html
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the CM_*CLKEN bits
are in CM_{I,F}CLKEN2_CORE [1]. Fix by implementing a custom clkops
.find_idlest function to return the correct slave IDLEST register.
...
1. OMAP2430 Multimedia Device Package-on-Package (POP) Silicon Revision 2.1
(Rev. V) Technical Reference Manual, tables 4-99 and 4-105.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some OMAP2/3 hardware modules have CM_IDLEST attributes that are not
handled by the current omap2_wait_clock_ready() code. In preparation
for patches that fix the unusual devices, rename the function
omap2_wait_clock_ready() to omap2_wait_module_ready() and split it
into three parts:
1. A clkops-specific companion clock return function (by default,
omap2_clk_dflt_find_companion())
2. A clkops-specific CM_IDLEST register address and bit shift return
function (by default, omap2_clk_dflt_find_idlest())
3. Code to wait for the CM to indicate that the module is ready
(omap2_cm_wait_idlest())
Clocks can now specify their own custom find_companion() and find_idlest()
functions; used in subsequent patches.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The clock stabilization delay post a M2 divider change is needed
even before a SDRC interface clock re-enable and not only before
jumping back to SDRAM.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch fixes a bug in the CORE dpll scaling sequence which was
errouneously clearing some bits in the SDRC DLLA CTRL register and
hence causing a freeze. The issue was observed only on platforms
which scale CORE dpll to < 83Mhz and hence program the DLL in fixed
delay mode.
Issue reported by Limei Wang <E12499@motorola.com>, with debugging
assistance from Richard Woodruff <r-woodruff2@ti.com> and Girish
Ghongdemath <girishsg@ti.com>.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Limei Wang <E12499@motorola.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Girish Ghongdemath <girishsg@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: updated patch description to include collaboration credits]
Stop setting SDRC_POWER.PWDENA on boot. There is a nasty erratum
(34xx erratum 1.150) that can cause memory corruption if PWDENA is
enabled.
Based originally on a patch from Samu P. Onkalo <samu.p.onkalo@nokia.com>.
Tested on BeagleBoard rev C2.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Samu P. Onkalo <samu.p.onkalo@nokia.com>
This patches ensures the MUX settings are correct for the SDRC
CKE signals to SDRAM. This allows the self-refresh to work when
2 chip-selects are in use.
A warning is thrown away in case the initial muxing is incorrect,
in order to track faulty or old-dated bootloaders.
Note: The CONFIG_OMAP_MUX and CONFIG_OMAP_MUX_WARNINGS options
must be enabled for the mux code to have effect.
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.
This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS
Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers
Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The combination of noexec=on and a clock_gettime call with clock id
CLOCK_THREAD_CPUTIME_ID is broken. The vdso code switches to the
access register mode to get access to the per-cpu data structure to
execute the magic ectg instruction. After the ectg instruction the
code always switches back to the primary mode but for noexec=on the
correct mode is the secondary mode. The effect of the bug is that the
user space program looses the access to all mappings without PROT_EXEC,
e.g. the stack. The problem is fixed by restoring the mode that has
been active before the switch to the access register mode.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
vdso per cpu area allocation in smp_prepare_cpus() happens with GFP_KERNEL
but irqs disabled. Triggers this one:
Badness at kernel/lockdep.c:2280
Modules linked in:
CPU: 0 Not tainted 2.6.30 #2
Process swapper (pid: 1, task: 000000003fe88000, ksp: 000000003fe87eb8)
Krnl PSW : 0400c00180000000 0000000000083360 (lockdep_trace_alloc+0xec/0xf8)
[...]
Call Trace:
([<00000000000832b6>] lockdep_trace_alloc+0x42/0xf8)
[<00000000000b1880>] __alloc_pages_internal+0x3e8/0x5c4
[<00000000000b1b4a>] __get_free_pages+0x3a/0xb0
[<0000000000026546>] vdso_alloc_per_cpu+0x6a/0x18c
[<00000000005eff82>] smp_prepare_cpus+0x322/0x594
[<00000000005e8232>] kernel_init+0x76/0x398
[<000000000001bb1e>] kernel_thread_starter+0x6/0xc
[<000000000001bb18>] kernel_thread_starter+0x0/0xc
Fix this by moving the allocation out of the irqs disabled section.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
swsusp_arch_suspend() actually saves all cpu register contents on
hibernation.
Machine checks must be disabled since swsusp_arch_suspend() stores
register contents to their lowcore save areas. That's the same
place where register contents on machine checks would be saved.
To avoid register corruption disable machine checks.
We must also disable machine checks in the new psw mask for
program checks, since swsusp_arch_suspend() may generate program
checks.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Our swsusp_arch_suspend() backend implementation disables prefixing
by setting the contents of the prefix register to 0.
However afterwards common code functions are called which might
access percpu data structures.
Since the lowcore contains e.g. the percpu base pointer this isn't
a good idea. So fix this by copying the hibernating cpu's lowcore to
absolute address zero.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Timer interrupts are excluded from being disabled during suspend. The
clock events code manages the disabling of clock events on its own
because the timer interrupt needs to be functional before the resume
code reenables the device interrupts.
The mfgpt timer request its interrupt without setting the IRQF_TIMER
flag so suspend_device_irqs() disables it as well which results in a
fatal resume failure.
Adding IRQF_TIMER to the interupt flags when requesting the mrgpt
timer interrupt solves the problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Cc: Andres Salomon <dilinger@debian.org>
Cc: stable@kernel.org
Update the NOR flash support for TS-7200.
The TS-7200 models all have 16-bit NOR flash. Update the platform
init to support this.
Remove the private TS72XX_NOR_* defines and use the common ep93xx
defines for the external chip select physical base address instead.
Move the NOR flash registration into a static __init function. When
the NAND flash support is updated this function will also be used
to register the NAND flash for the TS-7250 and TS-7260.
Tested-by: Matthieu Crapet <mcrapet@gmail.com>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch for at_hdmac adds the slave transfers capability to the Atmel DMA
controller available on some AT91 SOCs. This allow peripheral to memory and
memory to peripheral transfers with hardware handshaking.
Slave structure for controller specific information is passed through channel
private data. This at_dma_slave structure is defined in at_hdmac.h header file
and relative hardware definition are moved to this file from at_hdmac_regs.h.
Doing this we allow the channel configuration from platform definition code.
This work is intensively based on dw_dmac and several slave implementations.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on
at91sam9rl chip. It will be used on other products in the future.
This first release covers only the memory-to-memory tranfer type. This is the
only tranfer type supported by this chip. On other products, it will be used
also for peripheral DMA transfer (slave API support to come).
I used dmatest client without problem in different configurations to test it.
Full documentation for this controller can be found in the SAM9RL datasheet:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4243
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If CONFIG_APM_EMULATION=n em-x270 build fails with linker error:
arch/arm/mach-pxa/built-in.o: In function `em_x270_battery_critical': em-x270.c:(.text+0x12c0): undefined reference to `apm_queue_event'
arch/arm/mach-pxa/built-in.o: In function `em_x270_battery_low': em-x270.c:(.text+0x12c8): undefined reference to `apm_queue_event'
make: *** [.tmp_vmlinux1] Error 1
Fix it.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'perf-counters-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/peterz/linux-2.6-perf: (31 commits)
perf_counter tools: Give perf top inherit option
perf_counter tools: Fix vmlinux symbol generation breakage
perf_counter: Detect debugfs location
perf_counter: Add tracepoint support to perf list, perf stat
perf symbol: C++ demangling
perf: avoid structure size confusion by using a fixed size
perf_counter: Fix throttle/unthrottle event logging
perf_counter: Improve perf stat and perf record option parsing
perf_counter: PERF_SAMPLE_ID and inherited counters
perf_counter: Plug more stack leaks
perf: Fix stack data leak
perf_counter: Remove unused variables
perf_counter: Make call graph option consistent
perf_counter: Add perf record option to log addresses
perf_counter: Log vfork as a fork event
perf_counter: Synthesize VDSO mmap event
perf_counter: Make sure we dont leak kernel memory to userspace
perf_counter tools: Fix index boundary check
perf_counter: Fix the tracepoint channel to perfcounters
perf_counter, x86: Extend perf_counter Pentium M support
...
If we've logically disabled apics, don't probe the PCI space for the
AMD extended APIC ID.
[ Impact: prevent boot crash under Xen. ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Reported-by: Bastian Blank <bastian@waldi.eu.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
CONFIG_X86_THRESHOLD used in arch/x86/kernel/irqinit.c is always
undefined. Rename it to the correct name "CONFIG_X86_MCE_THRESHOLD".
Signed-off-by: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <4A667FD4.3010509@hitachi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Need to clear both nodes and nodes_add state for start/end.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <20090718065657.GA2898@basil.fritz.box>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
Fix the condition checking the result of strchr() (which previously
could result in an oops), and make the function return the number of
bytes actively used.
[ Impact: fix oops ]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
LKML-Reference: <4A5F04B7020000780000AB59@vpn.id2.novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The movq instruction, generated by __put_user_asm() when used for
64-bit data, takes a sign-extended immediate ("e") not a zero-extended
immediate ("Z").
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Uros Bizjak <ubizjak@gmail.com>
Cc: stable@kernel.org
arch/x86/include/asm/uaccess_64.h uses wrong asm operand constraint
("ir") for movq insn. Since movq sign-extends its immediate operand,
"er" constraint should be used instead.
Attached patch changes all uses of __put_user_asm in uaccess_64.h to use
"er" when "q" insn suffix is involved.
Patch was compile tested on x86_64 with defconfig.
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
The CompuLab SBC-fitPC2 board needs to reboot via BIOS.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (21 commits)
Blackfin: define HARDIRQ_BITS again for now
arch/blackfin: Add kmalloc NULL tests
Blackfin: add CPLB entries for Core B on-chip L1 SRAM regions
Blackfin: work around anomaly 05000189
Blackfin: drop per-cpu loops_per_jiffy tracking
Blackfin: fix bugs in GPIO resume code
Blackfin: bf537-stamp: fix irq decl for AD7142
Blackfin: fix handling of IPEND in interrupt context save
Blackfin: drop duplicate runtime checking of anomaly 05000448
Blackfin: fix incomplete renaming of the bfin-twi-lcd driver
Blackfin: fix wrong CTS inversion
Blackfin: update handling of anomaly 364 (wrong rev id in BF527-0.1)
Blackfin: fix early_dma_memcpy() handling of busy channels
Blackfin: handle BF561 Core B memory regions better when SMP=n
Blackfin: fix miscompilation in lshrdi3
Blackfin: fix silent crash when no uClinux MTD filesystem exists
Blackfin: restore exception banner when dumping crash info
Blackfin: work around anomaly 05000281
Blackfin: update anomaly lists to match latest sheets/usage
Blackfin: drop dead flash_probe call
...
The Blackfin serial headers were inverting the CTS value leading to wrong
handling of the CTS line which broke CTS/RTS handling completely.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix i2c_board_info definitions - we were defining the 'type' field
of these structures twice since the first argument of I2C_BOARD_INFO
sets this field. Move the second definition into I2C_BOARD_INFO().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
The .data.read_mostly and .data.cacheline_aligned sections
aren't covered by the _sdata .. _edata range on x86-64. This
affects kmemleak reporting leading to possible false
positives by not scanning the whole data section.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Alexey Fisher <bug-track@fisher-privat.net>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
LKML-Reference: <1247565175.28240.37.camel@pc1117.cambridge.arm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Sam Ravnborg <sam@ravnborg.org>
AMI BIOS with low memory corruption was found on Intel DG45ID
board (Bug 13710). Add this board to the blacklist - in the
(somewhat optimistic) hope of future boards/BIOSes from Intel
not having this bug.
Also see:
http://bugzilla.kernel.org/show_bug.cgi?id=13736
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Cc: ykzhao <yakui.zhao@intel.com>
Cc: alan@lxorguk.ukuu.org.uk
Cc: <stable@kernel.org>
LKML-Reference: <1247660169-4503-1-git-send-email-bug-track@fisher-privat.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
WARNING: at drivers/gpio/gpiolib.c:83 gpio_ensure_requested+0x58/0xbc()
autorequest GPIO-71
Modules linked in:
[<c0028bd0>] (unwind_backtrace+0x0/0xe8) from [<c003c328>] (warn_slowpath_common+0x48/0x78)
[<c003c328>] (warn_slowpath_common+0x48/0x78) from [<c003c394>] (warn_slowpath_fmt+0x28/0x38)
[<c003c394>] (warn_slowpath_fmt+0x28/0x38) from [<c0146128>] (gpio_ensure_requested+0x58/0xbc)
[<c0146128>] (gpio_ensure_requested+0x58/0xbc) from [<c0146308>] (gpio_direction_input+0x80/0xf4)
[<c0146308>] (gpio_direction_input+0x80/0xf4) from [<c000c668>] (zylonite_pxa300_init+0x108/0x214)
[<c000c668>] (zylonite_pxa300_init+0x108/0x214) from [<c000c4e4>] (zylonite_init+0x8/0x84)
[<c000c4e4>] (zylonite_init+0x8/0x84) from [<c00097cc>] (customize_machine+0x18/0x24)
[<c00097cc>] (customize_machine+0x18/0x24) from [<c00222e0>] (do_one_initcall+0x30/0x1b0)
[<c00222e0>] (do_one_initcall+0x30/0x1b0) from [<c00083f4>] (kernel_init+0xa4/0x11c)
[<c00083f4>] (kernel_init+0xa4/0x11c) from [<c0023f3c>] (kernel_thread_exit+0x0/0x8)
---[ end trace 1b75b31a2719ed1c ]---
This issue is caused by using gpio pin without request. Add gpio_request()
into zylonite. To simplify the code, error checking is omitted since this
is being performed early.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The BSS section macros in vmlinux.lds.h currently place the .sbss
input section outside the bounds of [__bss_start, __bss_end]. On all
architectures except for microblaze that handle both .sbss and
__bss_start/__bss_end, this is wrong: the .sbss input section is
within the range [__bss_start, __bss_end]. Relatedly, the example
code at the top of the file actually has __bss_start/__bss_end defined
twice; I believe the right fix here is to define them in the
BSS_SECTION macro but not in the BSS macro.
Another problem with the current macros is that several
architectures have an ALIGN(4) or some other small number just before
__bss_stop in their linker scripts. The BSS_SECTION macro currently
hardcodes this to 4; while it should really be an argument. It also
ignores its sbss_align argument; fix that.
mn10300 is the only user at present of any of the macros touched by
this patch. It looks like mn10300 actually was incorrectly converted
to use the new BSS() macro (the alignment of 4 prior to conversion was
a __bss_stop alignment, but the argument to the BSS macro is a start
alignment). So fix this as well.
I'd like acks from Sam and David on this one. Also CCing Paul, since
he has a patch from me which will need to be updated to use
BSS_SECTION(0, PAGE_SIZE, 4) once this gets merged.
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/fyu/linux-2.6:
Revert "Neither asm/types.h nor linux/types.h is required for arch/ia64/include/asm/fpu.h"
Add dma_debug_init() for ia64
Fix ia64 compilation IS_ERR and PTE_ERR errors.
asm/fpu.h uses the __IA64_UL macro which is declared in asm/types.h, so
this include is really required. Without it, GNU libc fails to build.
This reverts commit 2678c07b07.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
The commit 9916219579 was supposed to
add CONFIG_DMA_API_DEBUG support to IA64 however I forgot to add
dma_debug_init().
Signed-off-by: fujita <fujita@tulip.osrg.net>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
When building ia64 kernel with CONFIG_XEN_SYS_HYPERVISOR, compiler reports
errors:
drivers/xen/sys-hypervisor.c: In function ‘uuid_show’:
drivers/xen/sys-hypervisor.c:125: error: implicit declaration of function ‘IS_ERR’
drivers/xen/sys-hypervisor.c:126: error: implicit declaration of function ‘PTR_ERR’
This patch fixes the errors.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Isaku Yamahata <yamahata@valinux.co.jp>
Removed the LBD support that isn't of any use right now at least,
then remove remnants of the TCM config flags that somehow crept
in by mistake (not yet merged patch for 2.6.32) and then the usual
defconfig noise from updated menus.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid the following:
[ 0.012093] WARNING: at arch/x86/kernel/apic/apic.c:249 native_apic_write_dummy+0x2f/0x40()
Rather than chase each new cpuid-detected feature, just lie about the highest
valid CPUID so this code is never run.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The default values of HARDIRQ_BITS and PREEMPT_BITS in common code leads to
build failure:
In file included from include/linux/interrupt.h:12,
from include/linux/kernel_stat.h:8,
from arch/blackfin/kernel/asm-offsets.c:32:
include/linux/hardirq.h:66:2: error: #error PREEMPT_ACTIVE is too low!
So until that gets resolved, just declare our own default value again.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Check that the result of kmalloc is not NULL before passing it to other
functions.
In the first two cases, the new code returns -ENOMEM, which seems
compatible with what is done for similar functions for other architectures.
In the last two cases, the new code fails silently, ie just returns,
because the function has void return type.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression *x;
identifier f;
constant char *C;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
... when != x == NULL
when != x != NULL
when != (x || ...)
(
kfree(x)
|
f(...,C,...,x,...)
|
*f(...,x,...)
|
*x->f
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin SMP port was missing CPLB entries for Core B on-chip L1 SRAM
regions. Any code that attempted to use these would wrongly crash due to
a CPLB miss.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Similar to anomaly 05000281 but not as bad, we cannot return to the
instruction causing a fault otherwise we'll trigger a second false
exception. The system can still recover, but it isn't correct.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
On Blackfin SMP, a per-cpu loops_per_jiffy is pointless since both cores
always run at the same CCLK. In addition, the current implementation has
flaws since the main consumer for loops_per_jiffy (asm/delay.h) uses the
global kernel loops_per_jiffy and not the per_cpu one. So punt all of the
per-cpu handling and go back to the global shared one.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Change the bfin_gpio_pm_hibernate_restore() function to:
1) AND restored DATA with DIR (not OR) to get correct final state
2) Restore DATA before setting DIR to avoid glitches
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The AD7142 add-on card hooks the IRQ line up to PG5, not PF5.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The interrupt context save logic incorrectly stored the address of the
IPEND register rather than its value due to a missing dereference. While
we're here, also enable this code for all kernel debugging scenarios and
not just when KGDB is enabled.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We already catch this anomaly at compile time, and the runtime version is
such that it ends up checking on all parts rather than just the ones that
might actually have it.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The sed used to rename the bfin-twi-lcd only replaced the first instance
rather than all which led to the resources not being enabled when the
driver was built as a module.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin serial headers were inverting the CTS value leading to wrong
handling of the CTS line which broke CTS/RTS handling completely.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This anomaly only applies to the BF527-0.1, not the BF526-0.1, and not any
other revision of the BF527. So make sure we don't go returning 0xffff
for other cases.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The early logic to locate a free DMA channel and then set it up was broken
in a few ways that only manifested itself when we needed to set up more
than 2 on chip SRAM regions (most board defaults setup 1 or 2). First, we
checked the wrong status register (the destination gets updated, not the
source) and second, we did the ssync before rather than after resetting a
DMA config register.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than assume Core B is always run with caches turned on, let people
load into any of the on-chip memory regions. It is their business how the
SRAM/Cache regions are utilized, so don't prevent them from being able to
load into them.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The code used in the Blackfin lshrdi3 utilizes gcc constructs. However,
the structures declared don't line up with the code gcc generates, so
under certain optimizations, we get bad code and things crap out in fun
random ways. So rather than trying to maintain different gcc definitions
ourselves, just use the ones available in gcclib.h.
URL: http://blackfin.uclinux.org/gf/tracker/5286
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since we need to relocate the attached filesystem with the uClinux MTD map
(to handle some anomalies), we need to know its real filesize. If we boot
a kernel without a filesystem actually attached, we end up blindly reading
and copying garbage (since there is no magic value to detect validity).
Often times this results in an early crash and no output. So add a few
basic sanity checks before operating on things to catch the majority of
cases.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Previous unification code put the exception banner behind the "is oops"
logic when it should have been printed all the time.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add missing anomaly workaround for anomaly 05000281 - we can't return to
instructions which cause hardware errors otherwise we trigger the error
again which means we go into an infinite loop of handling, returning, and
retriggering. This work around confuses gdb when the error occurs as the
PC will seemed to have moved, so a better long term fix will need to be
figured out, but for now this is better than an infinite crash loop.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
There are no CONFIG_{BLK,CHR}_DEV_FLASH Kconfig options, and there is no
flash_probe() function, so not really sure what this code is all about.
Seems to be dead code that stretches way back to the start of the Blackfin
port.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Improve the assembly with a few explanatory comments and use symbolic
defines rather than numeric values for bit positions.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When moving load_up_altivec to vector.S a typo in a comment caused a
thinko setting the wrong variable.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On booke processors, gdb is seeing spurious SIGTRAPs when setting a
watchpoint.
user_disable_single_step() simply quits when the DAC is non-zero. It should
be clearing the DBCR0_IC and DBCR0_BT bits from the dbcr0 register and
TIF_SINGLESTEP from the thread flag.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
when building 32-bit, I see this ..
arch/x86/kernel/pvclock.c:63:7: warning: "__x86_64__" is not defined
Signed-off-by: Dave Jones <davej@redhat.com>
LKML-Reference: <20090713201437.GA12165@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The variable apic_numaq placed in noninit section references the
function wakeup_secondary_cpu_via_nmi(), which is in __cpuinit
section. Thus causes a section mismatch warning. To avoid such
mismatch we mark apic_numaq as __refdata.
We were warned by the following warning:
WARNING: arch/x86/kernel/built-in.o(.data+0x932c): Section mismatch in
reference from the variable apic_numaq to the function
.cpuinit.text:wakeup_secondary_cpu_via_nmi()
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
LKML-Reference: <b9df5fa10907120407p6b4f67dtf4d563155488188a@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The variable apic_es7000_cluster references the function __cpuinit
wakeup_secondary_cpu_via_mip() from a noninit section. So we've been
warned by the following warning. To avoid possible collision between
init/noninit, its best to mark the variable as __refdata.
We were warned by the following warning:
LD arch/x86/kernel/apic/built-in.o
WARNING: arch/x86/kernel/apic/built-in.o(.data+0x198c): Section
mismatch in reference from the variable apic_es7000_cluster to the
function .cpuinit.text:wakeup_secondary_cpu_via_mip()
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
LKML-Reference: <b9df5fa10907120404k6279a10ch5e9682432272706f@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I've attached a patch to remove the Pentium M special casing of
EMON and as noticed at least with my Pentium M the hardware PMU
now works:
Performance counter stats for '/bin/ls /var/tmp':
1.809988 task-clock-msecs # 0.125 CPUs
1 context-switches # 0.001 M/sec
0 CPU-migrations # 0.000 M/sec
224 page-faults # 0.124 M/sec
1425648 cycles # 787.656 M/sec
912755 instructions # 0.640 IPC
Vince suggested that this code was trying to address erratum
Y17 in Pentium-M's:
http://download.intel.com/support/processors/mobile/pm/sb/25266532.pdf
But that erratum (related to IA32_MISC_ENABLES.7) does not
affect perfcounters as we dont use this toggle to disable RDPMC
and WRMSR/RDMSR access to performance counters. We keep cr4's
bit 8 (X86_CR4_PCE) clear so unprivileged RDPMC access is not
allowed anyway.
Cc: Vince Weaver <vince@deater.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@googlemail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The name size limit is gone from the driver-core, the BUS_ID_SIZE
value will be removed.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 5fd29d6c ("printk: clean up handling of log-levels
and newlines"), the kernel logs segfaults like:
<6>gnome-power-man[24509]: segfault at 20 ip 00007f9d4950465a sp 00007fffbb50fc70 error 4 in libgobject-2.0.so.0.2103.0[7f9d494f7000+45000]
with the extra "<6>" being KERN_INFO. This happens because the
printk in show_signal_msg() started with KERN_CONT and then
used "%s" to pass in the real level; and KERN_CONT is no longer
an empty string, and printk only pays attention to the level at
the very beginning of the format string.
Therefore, remove the KERN_CONT from this printk, since it is
now actively causing problems (and never really made any
sense).
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <874otjitkj.fsf@shaolin.home.digitalvampire.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'core-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
dma-debug: Fix the overlap() function to be correct and readable
oprofile: reset bt_lost_no_mapping with other stats
x86/oprofile: rename kernel parameter for architectural perfmon to arch_perfmon
signals: declare sys_rt_tgsigqueueinfo in syscalls.h
rcu: Mark Hierarchical RCU no longer experimental
dma-debug: Put all hash-chain locks into the same lock class
dma-debug: fix off-by-one error in overlap function
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (50 commits)
perf report: Add "Fractal" mode output - support callchains with relative overhead rate
perf_counter tools: callchains: Manage the cumul hits on the fly
perf report: Change default callchain parameters
perf report: Use a modifiable string for default callchain options
perf report: Warn on callchain output request from non-callchain file
x86: atomic64: Inline atomic64_read() again
x86: atomic64: Clean up atomic64_sub_and_test() and atomic64_add_negative()
x86: atomic64: Improve atomic64_xchg()
x86: atomic64: Export APIs to modules
x86: atomic64: Improve atomic64_read()
x86: atomic64: Code atomic(64)_read and atomic(64)_set in C not CPP
x86: atomic64: Fix unclean type use in atomic64_xchg()
x86: atomic64: Make atomic_read() type-safe
x86: atomic64: Reduce size of functions
x86: atomic64: Improve atomic64_add_return()
x86: atomic64: Improve cmpxchg8b()
x86: atomic64: Improve atomic64_read()
x86: atomic64: Move the 32-bit atomic64_t implementation to a .c file
x86: atomic64: The atomic64_t data type should be 8 bytes aligned on 32-bit too
perf report: Annotate variable initialization
...
Pull the initial preempt_count value into a single
definition site.
Maintainers for: alpha, ia64 and m68k, please have a look,
your arch code is funny.
The header magic is a bit odd, but similar to the KERNEL_DS
one, CPP waits with expanding these macros until the
INIT_THREAD_INFO macro itself is expanded, which is in
arch/*/kernel/init_task.c where we've already included
sched.h so we're good.
Cc: tony.luck@intel.com
Cc: rth@twiddle.net
Cc: geert@linux-m68k.org
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen reported that his DL585 G2 needed noapic after 2.6.22 (?)
Dann bisected it down to:
commit 30a18d6c3f
Date: Tue Feb 19 03:21:20 2008 -0800
x86: multi pci root bus with different io resource range, on
64-bit
It turns out that:
1. that AMD-based systems have two HT chains.
2. BIOS doesn't allocate resources for BAR 6 of devices under 8132 etc
3. that multi-peer-root patch will try to split root resources to peer
root resources according to PCI conf of NB
4. PCI core assigns unassigned resources, but they overlap with BARs
that are used by ioapic addr of io4 and 8132.
The reason: at that point ioapic address are not inserted yet. Solution
is to insert ioapic resources into the tree a bit earlier.
Reported-by: Stephen Frost <sfrost@snowman.net>
Reported-and-Tested-by: dann frazier <dannf@hp.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@jbarnes-g45.(none)>
Commit 1faa16d228 accidentally broke
the bdi congestion wait queue logic, causing us to wait on congestion
for WRITE (== 1) when we really wanted BLK_RW_ASYNC (== 0) instead.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Ingo noticed that both AMD and P6 call
x86_pmu_disable_counter() on *_pmu_enable_counter(). This is
because we rely on the side effect of that call to program
the event config but not touch the EN bit.
We change that for AMD by having enable_all() simply write
the full config in, and for P6 by explicitly coding it.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The P6 doesn't seem to support cache ref/hit/miss counts, so
we extend the generic hardware event codes to have 0 and -1
mean the same thing as for the generic cache events.
Furthermore, it turns out the 0 event does not count
(that is, its reported that on PPro it actually does count
something), therefore use a event configuration that's
specified not to count to disable the counters.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add basic P6 PMU support. The P6 uses the EVNTSEL0 EN bit to
enable/disable both its counters. We use this for the
global enable/disable, and clear all config bits (except EN)
to disable individual counters.
Actual ia32 hardware doesn't support lfence, so use a locked
op without side-effect to implement a full barrier.
perf stat and perf record seem to function correctly.
[a.p.zijlstra@chello.nl: cleanups and complete the enable/disable code]
Signed-off-by: Vince Weaver <vince@deater.net>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <Pine.LNX.4.64.0907081718450.2715@pianoman.cluster.toy>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
cxgb3: Fix crash caused by stashing wrong netdev_queue
ixgbe: Fix coexistence of FCoE and Flow Director in 82599
memory barrier: adding smp_mb__after_lock
net: adding memory barrier to the poll and receive callbacks
netpoll: Fix carrier detection for drivers that are using phylib
includecheck fix: include/linux, rfkill.h
p54: tx refused but queue active
Atheros Kconfig needs to be dependent on WLAN_80211
mac80211: fix docbook
mac80211_hwsim: avoid NULL access
ssb: Add support for 4318E
b43: Add support for 4318E
zd1211rw: adding SONY IFU-WLM2 (054c:0257) as a zd1211b device
zd1211rw: 07b8:6001 is a ZD1211B
r6040: bump driver version to 0.24 and date to 08 July 2009
r6040: restore MIER register correctly when IRQ line is shared
ipv4: Fix fib_trie rebalancing, part 4 (root thresholds)
davinci_emac: fix kernel oops when changing MAC address while interface is down
igb: set lan id prior to configuring phy
mac80211: minstrel: avoid accessing negative indices in rix_to_ndx()
...
The short name of the achitecture is 'arch_perfmon'. This patch
changes the kernel parameter to use this name.
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Adding smp_mb__after_lock define to be used as a smp_mb call after
a lock.
Making it nop for x86, since {read|write|spin}_lock() on x86 are
full memory barriers.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the VIC resume from suspend flagged IRQ:s identical to
the flags indicating all possible interrupts. This is perhaps not
the optimal setting but setting it to 0 makes the system suspend
and never come back again (all IRQ sources masked off).
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
<linux/io.h> was getting included by <mach/ts72xx.h>, is should be
included by this file.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Alex found that specjbb2005 still can not run with hugepages on an
x86-64 machine. This only happens when numa is not compiled in.
The root cause: node_set_state will not set it back for us in that case,
so don't clear that when numa is not select in config
[ v2: use node_clear_state instead ]
Reported-and-Tested-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 5fd29d6ccb ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Powernow-k8: support family 0xf with 2 low p-states
[CPUFREQ] fix (utter) cpufreq_add_dev mess
[CPUFREQ] Cleanup locking in conservative governor
[CPUFREQ] Cleanup locking in ondemand governor
[CPUFREQ] Mark policy_rwsem as going static in cpufreq.c wont be exported
[CPUFREQ] Eliminate the recent lockdep warnings in cpufreq
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM: Clear -EAGAIN in dpm_prepare
x86: Fix resume from suspend when CONFIG_CC_STACKPROTECTOR
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Don't use alloc_bootmem() in init_IRQ() path
powerpc: Fix spin_event_timeout() to be robust over context switches
powerpc: Use pr_devel() in do_dcache_icache_coherency()
powerpc/cell: Use pr_devel() in axon_msi.c
powerpc: Use pr_devel() in arch/powerpc/mm/gup.c
powerpc: Cleanup & use pr_devel() in arch/powerpc/mm/slb.c
powerpc/perf_counter: Remove duplicated #include
powerpc: Use pr_devel() in arch/powerpc/mm/mmu_context_nohash.c
powerpc/pseries: Use pr_devel() in xics.c
powerpc: Remove unnecessary semicolons
powerpc/pseries: Use pr_devel() in pseries LPAR HPTE routines
powerpc/44x: Fix build error with -Werror for Warp platform
powerpc/4xx: Have Warp take advantage of GPIO LEDs default-state = keep
powerpc/44x: Update Warp defconfig
Patch 08687aec71bc9134fe336e561f6did877bacf74fc0a (x86: unify
power/cpu_(32|64).c) renamed cpu_32.c to cpu.c, but did not update
the special compilation flags for the file for the new name.
This patch fixes the compilation flags, and therefore fixes resume
from suspend on my Acer Aspire One.
[rjw: The regression from 2.6.30 fixed by this patch is tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=13661]
Signed-off-by: Peter Chubb <peterc@nicta.com.au>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Current implementation of spin_event_timeout can be interrupted by an
IRQ or context switch after testing the condition, but before checking
the timeout. This can cause the loop to report a timeout when the
condition actually became true in the middle.
This patch adds one final check of the condition upon exit of the loop
if the last test of the condition was still false.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
2036 368 8 2412 96c arch/powerpc/mm/pgtable.o
size after:
text data bss dec hex filename
1677 248 8 1933 78d arch/powerpc/mm/pgtable.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
7083 1616 0 8699 21fb arch/powerpc/../axon_msi.o
size after:
text data bss dec hex filename
5772 1208 0 6980 1b44 arch/powerpc/../axon_msi.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
3252 384 0 3636 e34 arch/powerpc/mm/gup.o
size after:
text data bss dec hex filename
2576 96 0 2672 a70 arch/powerpc/mm/gup.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
3261 416 4 3681 e61 arch/powerpc/mm/slb.o
size after:
text data bss dec hex filename
2861 248 4 3113 c29 arch/powerpc/mm/slb.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
1508 48 28 1584 630 powerpc/mm/mmu_context_nohash.o
size after:
text data bss dec hex filename
1088 0 28 1116 45c powerpc/mm/mmu_context_nohash.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
7720 5488 296 13504 34c0 platforms/pseries/xics.o
size after:
text data bss dec hex filename
7535 5456 296 13287 33e7 platforms/pseries/xics.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pr_debug() can now result in code being generated even when DEBUG
is not defined. That's not really desirable in some places.
In particular, pSeries_lpar_hpte_insert() goes from 185 instructions
to 77 instructions as a result of this patch. Luckily that code
isn't called very often ...
With CONFIG_DYNAMIC_DEBUG=y:
size before:
text data bss dec hex filename
7284 1552 296 9132 23ac platforms/pseries/lpar.o
size after:
text data bss dec hex filename
5806 1096 296 7198 1c1e platforms/pseries/lpar.o
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
32-bit s390 has efficient support for 64/32-bit conversions, define
KTIME_SCALAR to enable the use of the plain scalar nanosecond based
representation of ktime.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Performance counters need 64 bit atomic operations.
To keep the patch small we use the simple generic atomic64_t implementation.
The native implementation follows with the next kernel.
Fixes this build bug:
In file included from kernel/sched.c:42:
include/linux/perf_counter.h:427: error: expected specifier-qualifier-list before 'atomic64_t'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide __ucmpdi2() helper function on 31 bit so we don't run
again and again in compile errors like this one:
kernel/built-in.o: In function `T.689':
perf_counter.c:(.text+0x56c86): undefined reference to `__ucmpdi2'
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add PERF_COUNTER_INDEX_OFFSET define to fix this build bug:
kernel/perf_counter.c: In function 'perf_counter_index':
kernel/perf_counter.c:1889: error: 'PERF_COUNTER_INDEX_OFFSET' undeclared
Same fix as for FRV since s390 doesn't support hw counters.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We always returned -EINVAL when setting of a shutdown action failed. This was
misleading, if for example the hardware did not support the shutdown action.
Now we save each shutdown action's init return code and return it when the
action is being set.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
