In isl_38xx.c
In routine isl38xx_trigger-device
Move unnecessary udelay/register read.
This is only required when hand-compiling the driver and
setting VERBOSE > SHOW_ERROR_MESSAGES
Signed-off-by: Roger While <simrw@sim-basis.de>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This header file patch was missing from the recent SAA9730 patch.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch implements the UFO support in S2io driver. This patch uses the UFO
interface available in linux-2.6.15 kernel.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
For the four versions of hardware that we (currently) support microcode
download on, the default configuration of our receive interrupt mitigation
microcode was too aggressive, and caused unnecessary delays when pinging,
and low(er) throughput on single connection latency sensitive performance
tests.
This code adds microcode support, and sets the defaults to more reasonable
settings. It also explains the functionality in the code in more detail.
Compile and load tested, shows expected behavior for slight delay of ping
packets (1-2ms) when ucode is loaded, and decent interrupt moderation for
small packets, while maintaining good throughput.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The smc91x driver relies upon register bank 2 being selected whenever
the interrupt handler is called. This isn't always so, especially if
we have a link change event during PHY configuration.
This results in register bank 0 being selected when the interrupt
handler is called, causing the wrong registers to be read for the
IRQ mask and status. In turn, this causes us to spin with a
permanently asserted IRQ.
The patch ensures that smc_phy_configure always exits with register
bank 2 selected.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Not only SMC_ACK_INT(IM_TX_EMPTY_INT) in in smc_hardware_send_pkt)
appears to be unnecessary (tested with an SMC91C94 and SMC91C111), but
it seems to trigger spurious interrupts on some machines as well.
Removed.
While at it, let's log any remaining spurious interrupts if any (and
clean usage of the max IRQ loop count value).
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This fixes a slab corruption issue in the ipw2200 driver: it essentially
multiplied the error log number _twice_ by the size of the error element
entry (once explicitly in the code, and once implicitly as part of the
regular pointer arithmetic).
Cc: Henrik Brix Andersen <brix@gentoo.org>
Cc: Bernard Blackham <bernard@blackham.com.au>
Cc: Zilvinas Valinskas <zilvinas@gemtek.lt>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
--
The function ipw_request_direct_scan() should bail out when the device
is down. This fixes a lockup caused by wpa_supplicant triggering
ipw_request_direct_scan() while the driver was in a middle of a reset
due to firmware errors.
Thanks to Zilvinas Valinskas for reporting the bug and helping me
debug it.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The capabilities of the 8169 can be disabled but it is hardly a reason
to prevent the use the device. The (so far) unusual behavior has been
reported on a MIPS platform by Yoichi Yuasa.
Spotted-by: Yoichi Yuasa <yuasa@hh.iij4u.or.jp>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
I keep on getting "printk: N messages suppressed" messages. We need to test
netif_msg_intr() _before_ running printk_ratelimit(), because the latter
updates state.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
I wanted to remove the #include "hostap_ioctl.c" from hostap.c and
build hostap_ioctl.c separately, but this doesn't work since hostap.c
has the same name as the module.
After renaming hostap.c this will be possible.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Christophe Lucas <clucas@rotomalug.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reading this driver I noticed some trailing whitespaces and tabs so I
removed them with some 80th column fitting and a few more similar
things.
Signed-off-by: Carlo Perassi <carlo@linux.it>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"grep "lmc_prot\." -r ." didn't show anything.
lmc_proto.h seems to have the correct prototypes, and is actually used.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Making SkPciWriteCfgDWord a static inline produces a warning due to a
forward declaration in skdrv2nd.h. This patch removes that declaration.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No external user and that small - such a function should be static
inline and not a global function.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As we are currently unable to fix the problem with carrier and protocol
state signaling in net core I've to disable netif_carrier_off()
calls used by WAN protocol drivers. The attached patch should make
them working again.
The remaining netif_carrier_*() calls in hdlc_fr.c are fine as they
don't touch the physical device.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enablement patch for the new PowerBooks (late 2005 edition).
This enables the ATA controller, Gigabit ethernet and basic AGP setup.
Bluetooth works out-of-the box after running hid2hci.
Still remaining is to get the touchpad to work, the simple change of just
adding the new USB ids isn't enough.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Changed jobs and the Freescale address is no longer valid.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since few people need the support anymore, this moves the legacy
pm_xxx functions to CONFIG_PM_LEGACY, and include/linux/pm_legacy.h.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bonding source files still have changelogs in the comments. This, then,
is an update to that changelog.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Minor spelling and whitespace corrections.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the version number for the bonding module. Since we've just
added a significant new feature (sysfs support), bump the major number.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This large patch adds sysfs functionality to the channel bonding module.
Bonds can be added, removed, and reconfigured at runtime without having
to reload the module. Multiple bonds with different configurations are
easily configured, and ifenslave is no longer required to configure bonds.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the /proc files show which ARP targets are in use by each bond.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the sysfs interface, the user can remove entries from the ARP table
at runtime. The ARP monitor code now allows for empty entries in the
table.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sysfs interface can create bonds at runtime, and __init code goes away
after module init.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sysfs interface can create bonds at runtime, so we need a separate
function to do this, instead of just doing it in the module init code.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sysfs code needs access these functions, so make them
not static, and move the protos to the header file.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sysfs code needs to know what these structs look like, so make them
not static, and move the definition to the header.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Explicitly clear RLB flag during ALB init. This is needed for sysfs
support, since the bond mode can be changed at runtime via sysfs.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move memory allocations out of the spinlock during ALB init. This gets
rid of a sleeping-inside-spinlock warning and accompanying stack dump.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Take the primary slave name shown in /proc from the actual slave dev
instead of from the command-line parameter, which won't be present
if the bond is created via sysfs.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adds information about the recently-added transmit policy setting to each
bond's /proc file.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Expand and correct the parameter descriptions shown by modinfo.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the bond name to all error messages so we can tell which one is
complaining. Also reformats some error messages to be more consistent.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the ISO C9x conversion gcc deprecates concatenation with
__FUNCTION__ because __FUNCTION__ is not a preprocessor macro.
Signed-off-by: Clemens Buchacher <drizzd@aon.at>
Signed-off-by: Maximilian Attems <janitor@sternwelten.at>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The following patch support the SMC9111 present on DB1200 boards.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
o Try to work around some of the undocumented "features" of the SAA9730
o Use netdev_priv() instead of the previous broken mechanism to allocate
the private data structure.
o Try to make sure we don't leak resources on exit.
o No more need to call SET_MODULE_OWNER in 2.6.
o Use pci_free_consistent instead of homegrown architecture-specific
allocation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/saa9730.c | 531 +++++++++++++++++++++++---------------------------
1 files changed, 249 insertions(+), 282 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch contains support for different modes of interrupt mitigation
of forcedeth. It includes changes based on Jeff's comments. Currently,
the modes are changed through module parameters since ethtool does not
support something similar.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
To ensure that phy_mask and any future elements of the mii_bus
structure are initialized use kzalloc() instead of kmalloc().
This fixes an issue in which phy_mask was not being initialized
and we would skip random phy addresses when scanning.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
* Merge PCMCIA card table with new Brodowski PCMCIA id table.
* Add missing entries to PCMCIA id table.
* Other tweaks to conform with Documentation/driver-changes.txt
(types, call request_region, etc)
* Fix size of requested IO region.
* Reduce printk verbosity.
* Remove EXPERIMENTAL
* tweak to association code - don't force shared key authentication
when wep in use.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
On alpha:
drivers/net/sky2.c: In function `sky2_probe':
drivers/net/sky2.c:2819: error: `DMA_64BIT_MASK' undeclared (first use in this function)
drivers/net/sky2.c:2819: error: (Each undeclared identifier is reported only once
drivers/net/sky2.c:2819: error: for each function it appears in.)
drivers/net/sky2.c:2825: error: `DMA_32BIT_MASK' undeclared (first use in this function)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
At the moment ibmveth has DEBUG enabled which is rather verbose. Disable
it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove the superfluous parameter checking in bnx2_{get,set}_eeprom.
The parameters are already validated in ethtool_{get,set}_eeprom.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check return of dev_alloc_skb in bnx2_test_loopback, and handle
appropriately.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Output driver name as prefix to "Unknown flash/EEPROM type." message.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rtl8139 thread is triggered only on rare 8139 hardware, the race
itself is unlikely, and the impact of racing is low. We don't care
enough to create a more-complex race-free solution.
Rather, if the trylock fails, we now simply poll twice a second until
we do get the lock.
Due to the recent update of the platform code, some platform device
drivers fail to compile. This fix is for fs_enet, adding #include of a
new header, to which a number of platform stuff has been relocated.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows us to eliminate the casts in the drivers, and eventually
remove the use of the device_driver function pointer methods for
platform device drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes almost all inclusions of linux/version.h. The 3
#defines are unused in most of the touched files.
A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is
unfortunatly in linux/version.h.
There are also lots of #ifdef for long obsolete kernels, this was not
touched. In a few places, the linux/version.h include was move to where
the LINUX_VERSION_CODE was used.
quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'`
search pattern:
/UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes compiler warnings when CONFIG_ISA and CONFIG_PCI are not
enabled in the dgrc network driver.
Signed-off-by: Ashutosh Naik <ashutosh.naik@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Usual fix:
- b44_interrupt() does not schedule NAPI polling when the device is
going down;
- b44_close() waits for any scheduled NAPI polling before it starts
to release the private structures of the device.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Increase the driver version number and print version when
probing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use prefetch() in the interrupt path to try and look ahead
at the next place will be looking at in the ring.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When skge is booted up, the PHY may be stuck in power down state
by the previous OS. So we may need to turn it on.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Update the support for the 16550 present on most IOC3 configurations to use
the current API.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Andrew Morton <akpm@osdl.org>
Two missing unlocks, as noted by Ted Unangst <tedu@coverity.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Matt Domsch <Matt_Domsch@dell.com>
The patch below implements the Microsoft Point-to-Point Encryption method
as a PPP compressor/decompressor. This is necessary for Linux clients and
servers to interoperate with Microsoft Point-to-Point Tunneling Protocol
(PPTP) servers (either Microsoft PPTP servers or the poptop project) which
use MPPE to encrypt data when creating a VPN.
This patch differs from the kernel_ppp_mppe DKMS pacakge at
pptpclient.sourceforge.net by utilizing the kernel crypto routines rather
than providing its own SHA1 and arcfour implementations.
Minor changes to ppp_generic.c try to prevent a link from disabling
compression (in our case, the encryption) after it has started using
compression (encryption).
Feedback to <pptpclient-devel@lists.sourceforge.net> please.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Cc: James Cameron <james.cameron@hp.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: "Philippe De Muyter" <phdm@macqel.be>
This patch avoids ppp-generated kernel crashes on machines where unaligned
accesses are forbidden (ie: m68000), by fixing ppp alignment setting for
reused skb's.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
More conversions of kmalloc/memset to kzalloc
Signed-off-by: Panagiotis Issaris <takis@issaris.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Specify the correct range when calling memset in atmel_get_range.
Do this by specifying the size of the structure, rather than the size
of the pointer.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch below fixes the following sparse warnings:
drivers/net/e100.c:1481:13: warning: Using plain integer as NULL pointer
drivers/net/e100.c:1767:27: warning: Using plain integer as NULL pointer
drivers/net/e100.c:1847:27: warning: Using plain integer as NULL pointer
Signed-off-by: Luiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move update of the transmit statistics to the correct place. This
would be just before starting transmission rather than (potentially
long) afterward.
Signed-off-by: Roger While <simrw@sim-basis.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In isl_38xx.c :
The variable "counter" is defined and incremented but never
used except if the driver is hand-compiled setting
VERBOSE > SHOW_ERROR_MESSAGES.
Move the definition and the increment to within the
#if VERBOSE .. block.
Remove extraneous udelay's.
These are not required when triggering the device.
Signed-off-by: Roger While <simrw@sim-basis.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch kills include/linux/eeprom.h .
Rationale:
- it was only used by one single driver
- even this driver didn't do anything useful with it
- most of this file are non-inline and non-static functions (sic)
This removes include/linux/eeprom.h and cleans drivers/net/ns83820.c up.
If you think eeprom.h should be used more extensively, please consider:
- the code has to be moved from the header file to a .c file
- the currently empty write function has to be implemented
- ns83820.c or any other driver should actually use it
Noone did any of these during the more than 3 years eeprom.h already
exists...
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should resolve http://bugzilla.kernel.org/show_bug.cgi?id=5519
The current feature computation loses bits that it doesn't know about,
resulting in an inability to add VLANs and possibly other havoc.
Rewrote function to preserve bits it doesn't know about, remove an
unneeded state variable, and simplify the code.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
configured.
Countermeasures default to being turned off when wpa_supplicant runs,
regardless of if TKIP is being used. They are only turned on if a TKIP
is running. The warning we were printing is therefore not needed.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Wireless extensions moved the get_wireless_stats handler from being
in net_device into wireless_handler.
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
The problem is caused by the patch in bug455 -- Channel change flood
generates fatal error.
The patch set the DISASSOCIATING status bit after sending the command.
The process was scheduled out when waiting for the command to be sent to
the card. The disassociated notification clears the DISASSOCIATING bit
in the tasklet before the process set the bit.
Move the bit setting code before sending the command now.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
The PF_SYNCTHREAD check was introduced to try and remain compatible with
SWSUSP2. This check is no longer needed with newer versions.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
error when it tries to auth to a WPA ap. The patch filters out WPA
networks if the card is not wpa enabled when selecting network to
associate to.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Because of the frequent channel change, it is possible that when we are
try to associate with channel 1 (authenticated but not associated).
Another channel change comes at this time, then the driver will issue
disassociate command to the firmware which will cause the fatal error.
It seems that the association/disassociation procedure should not be
interrupted.
The patch attached adds test on STATUS_ASSOCIATING | STATUS_DISASSOCIATING
in ipw_send_cmd(), when ensures that commands will not be sent to firmware
when we are in these two status.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
(handle_probe_response, handle_beacon, handle_association_response).
Fixed a problem with ipw_send_cmd() returning non-zero on success.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
You can now specify via the module parameter 'cmdlog' to allocate a
ring buffer for caching host commands sent to the firmware. They can
then be dumped at any time via the sysfs entry 'cmd_log'
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
codes to the caller and changed ipw_send_cmd itself to print the error
message to the syslog indicating which command failed to be sent.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
via sysfs even if debugging disabled. When a firmware error is
captured, it will be dumped to the kernel log (if debug enabled) and
captured in memory to be retrieved via sysfs.
If an error has already been captured, subsequent errors will be
dropped.
The existing error can be cleared by writing to the error log entry.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
with request_scan being called before initialized if invoked from
insmod, resulting in no association occurring during boot until iwlist
scan is run.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
If we configure the wep keys after creating the ibss network, the
beacons of this network will not show correctly (it still shows "key
off" in iwlist scan report). This is because we don't update the
beacon info in firmware.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
iwconfig matches what their hardware can actually do in regard to
supported channel maps, etc.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
We send SYSTEM_CONFIG command after the TGI_KEY command if hardware
encryption is enabled. It sometimes causes a firmware stall (firmware
doesn't respond to any request) and finally bungs up the Tx send queue.
The solution is to send SYSTEM_CONFIG command in the post association
stage from a workqueue.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
* Fixed#452 problem with setting retry limit (thanks to Hong Liu)
* Fixed#592 race condition during association causing firmware errors
* Fixed#602 problem with building in 64-bit environment
* Fixed#625 problem with SCAN_REQUEST_EXT sometimes failing
* Fixed#645 problem with bit rate not decreasing when moving laptop
farther from AP
* Fixed#656 problem with 'iwconfig eth1 mode auto' and 'modprobe'
locking the system
* Fixed#667 problem with "No space for Tx" for hwcrypto=1
* Fixed#685 kernel panic in rmmod caused by led work is still queued
* Fixed#695 problem with network doesn't reassociate after suspend/resume
* Fixed#701 problem with 'iwprvi sw_reset' not resetting the card from
monitor mode
* Fixed#710 problem with monitor mode being used after a WEP key has
been configured
* Fixed network->mode vs. priv->ieee->iw_mode checking (thanks to Ben Cahill)
* Fixed "Unknown management packet %d" warning
* Fixed setting channels multiple times in monitor mode causes scan stopped
* Fixed ipw_wx_sw_reset doesn't switch firmware if mode is changed.
* Add duplicate packet checking code (kill ping DUP! and TKIP replay warning)
* Fix hardware encryption (both WEP and AES) doesn't work with fragmentation.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
support wpa_supplicant with open AP. We need this to make driver_ipw
work.
driver_ext has already had the similar code with the WE-18 support
added.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
* Added WE-18 support. This allows the use of -Dext with wpa_supplicant
> 0.4.x (thanks to Hong Liu)
* Fixed#339 problem with iwconfig set/get txpower (thanks to Hong Liu)
* Fixed#598 problem when with error messages when module loaded with
'disable=1' (thanks to Hong Liu)
* Fixed#640 problem with 'iwlist retry' now showing min/max retry
* Fixed compatibility with wpa_supplicant and the new -Dipw interface
(that included a fix for 64-bit compatibility)
* Added CFG_CRC_CHECK which allows passing through packets with bad
CRCs while in monitor mode.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
* Fixed#627 problem with open APs not working with wpa_supplicant
* Fixed#632 problem with 'txpower auto' setting power incorrectly (thanks
to Kai Groner)
* Fixed#634 problem with 'iwconfig eth1 frag 0' hanging the shell
* Fixed problem with adapter not fully powering off during suspend to RAM or
when module unloaded.
* Fixed#645 problem with turning fixed rates off not taking effect until
you reload the driver
* Fixed problem with firmware restart if wpa_supplicant was used to set a key
that wasn't exactly 5 or 13 bytes in length.
* Fixed#623 Added iwpriv sw_reset extension to reset sw parameters
* Added managment frame export to user space with frame statistics
* Fixed#652 Modified the driver to load the EEPROM data even if RF KILL is
active during driver load
* Global s:CX2_:IPW_:g to make code more consistent
* Fixed#572 problem with setting txpower to auto
* Fixed#656 problem with kernel oops if mode auto; modprobe -r ipw2200
* Added QoS (CONFIG_IPW_QOS) support. This is being actively developed but
is the first step in getting WMM support into the driver and the kernel.
* Fixed some race conditions with channel changes, association, and scan
abort that could periodically cause a firmware restart.
* Added some extensions to export scan and network statistics to user space
(exposed through speed_scan and net_stats sysfs entries)
* Fixed a few bugs in how monitor mode was supported (scan lists
weren't quite right)
* Updated the firmware requirement from 2.2 to 2.3 which supports
monitor mode.
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
* Fix#616 problem with OOPS on module load (thanks to Yi Zhu)
* Fixed problem with led module parameter being described as
'auto_create'
* Added support to merge between adhoc networks (thanks to Mohamed Abbas)
* Added semaphore lock at the driver's entry points to protect against
re-entry (thanks to Mohamed Abbas)
* Added semaphore lock to background scheduled driver actions (thanks to
Mohamed Abbas)
* Changed how signal quality is reported for scan output (thanks to
Peter Jones)
* Fixed how high/low clamp values of signal quality are reported so a
more consistent ramp is provided (thanks to Bill Moss)
* Fix#624 problem with duplicate addresses (again) (thanks to Bernard
Blackham)
* Fix#385 problem with fragmentation and certain sized packets (thanks
to Mohamed Abbas)
* Modified iwconfig network name if RF kill is enabled to say 'radio off'
* Fix#382 problem with driver not responding to probe requests in Ad-Hoc
mode (thanks to Mohamed Abbas)
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Removed unneeded parenthesis around numeric constant defines
Added support for iwspy
Put in fix for Ad-Hoc mode not passing through all packets (thanks to KKH)
Put in fix for fragmentation not working for fragment sizes between
441-464 bytes (thanks to Mohamed Abbas)
Fixed#592 problem of CONFIG_IEEE80211_WPA_MODULE not including WPA
support into the driver -- fixed as a result of no longer limiting WPAs
inclusion
Fixed#594 problem with user rates mask causing lack of association if
AP mandatory rate is masked out. We now add back in as a supported rate
any mandatory rate.
Fixed#597 kernel oops due to calling dev_kfree_skb on an skb multiple times.
Added code to control LEDs that can be controlled through the wireless
NIC (vs. non-wireless HW interfaces) -- this is currently disabled by
default due to reports by some users of it hanging their laptop.
Added some more debug messages around fragmentation logic
Added locking around STATUS_HCMD_ACTIVE to prevent re-entry race
conditions
Moved ipw_adapter_restart to only execute on the priv->workqueue to
keep keyboard errors from occuring during adapter restart
Added CFG_BACKGROUND_SCAN to easily allow people to play with
background scanning implementations
Modified WPA logic to send WPA IE if one is set (vs. being based on
wpa_enabled)
Modified scan result logic to report WPA and RSN IEs if set (vs. being
based on wpa_enabled)
Fixed issues with endianess compatability between the host and
wireless adapter (thanks to York Liu and Yi Zhu)
Fixed problem with Ad-Hoc network creation causing a firmware error if
a scan was actively running (thanks to Mohamed Abbas)
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
This commit contains the following fixes:
Fixed#559: iwconfig rate support (thanks to Florian Hackenberger)
Improved link signal quality calculation (thanks to Bill Moss)
Fixed a problem with sensitivity threshold during association
Added iwpriv for turning forcing long preamble support:
% iwpriv eth1 set_preamble 1|0
Fixed#542 and #377 support for short preamble
Fixed locked BSSID reporting channel number (thanks to Pedro
Ramalhais)
Fixed type-o with scan watchdog timeout message (thanks to Pedro
Ramalhais)
Changed logic for displaying get_mode output so the code is easier to
follow (thanks to Pedro Ramalhais)
Added initial support for WPA (thanks to Yi Zhu) -- tested with
wpa_supplicant (either tip w/ ipw driver, or with -Dipw2100) with
both CCMP and TKIP
Fixed problem with CCMP not working due to uninitialized 802.11
header fields (thanks to Pedro Ramalhais)
Bug references are to defects stored on http://bughost.org
Signed-off-by: James Ketrenos <jketreno@linux.intel.com>
Add support for the new 5208 ColdFire (Matt Waddel / Mike Lavender)
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
I also re-ordered the init code to avoid interrupt lockups on
some platforms (at least the 5275, but others have reported it on
the 5235 as well).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the new 5208 ColdFire in the FEC ethernet header.
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is not valid to enable scatter/gather without hardware checksum support
of some kind. (akpm: applies only to the old boomerang cards).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add capability for 3c59x driver to use memory-mapped PCI I/O resources.
This may improve performance for those devices so equipped. This will be
the default behaviour for IS_CYCLONE and IS_TORNADO devices. Additionally,
it can be enabled/disabled individually for up to MAX_UNITS number of
devices via the use_mmio module option or for all units via the
global_use_mmio option. The use_mmio option overrides the global_use_mmio
option for those devices specified.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only increment rx_dropped in case of lack of resources (i.e. not for
frames with errors).
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for ETHTOOL_GPERMADDR to 3c59x.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Correct several (apparently cut & paste) grammatical typos in module
parameter descriptions. They seem to have originated as copies of the
description for "global_options".
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Beautify the array initilizations for the module parameters.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add bounds checking to usage of hw_checksums module parameter array.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In order to spare some I/O operations, be more intelligent about when to
read from the PHY.
Pointed out by Bogdan Costescu.
Signed-off-by: Tommy S. Christensen <tommy.christensen@tpack.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up mdio_read routines in 3c59x.c to use the MII_* macros defined in
include/linux/mii.h
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert 3c59x driver to use pci_iomap API. This makes it easier to enable
the use of memory-mapped PCI I/O resources.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't request_irq before the registers are reset/init.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
There is no need to save/restore the irq state as the irq are always
locally disabled when b44_interrupt is issued.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- remove unneeded forward declarations
- s/kmalloc + memset/kzalloc/
- whitespace readjustement can't hurt
- wrong comment: b44_init_rings _is_ called with a spinlock held in
b44_{open/set_ringparam/set_pauseparam/etc}.
Actually, it does not need to be able to sleep
- b44_remove_one() can not be issued with a NULL device in its
private member: remove the test.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The patch simply factors out the release of the lock.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch creates a file airo.h containing prototypes of the global
functions in airo.c used by airo_cs.c .
If you got strange problems with either airo_cs devices or in any other
completely unrelated part of the kernel shortly or long after a airo_cs
device was detected by the kernel, this might have been caused by the
fact that caller and callee disagreed regarding the size of the first
argument to init_airo_card()...
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Refine bnx2_poll() logic to write back the most up-to-date status tag
when all work has been processed. This eliminates some occasional
extra interrupts when a older status tag is written even though all
work has been processed.
The idea is to read the status tag just before exiting bnx2_poll() and
then check again for any new work. If no new work is pending, the
status tag written back will not generate any extra interrupt. This
logic is similar to the changes David Miller did to tg3_poll().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dynamically determine the shared memory location where eeprom
parameters are stored instead of using a fixed location.
Add speed reporting to management firmware. This allows management
firmware to know the current speed without contending for MII
registers.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update bnx2 nvram code with support for 5708.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add 5708 copper and serdes basic support, including 2.5 Gbps support
on 5708 serdes. SPEED_2500 is also added to ethtool.h
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last patch I sent in ("prism54: Free skb after disabling
interrupts") included a redundant NULL assignment. Thanks to Herbert
Xu for pointing it out.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems dmascc_setup() is a leftover time before dmascc_init() was
there.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains the following possible cleanups:
- make needlessly global code static
- #if 0 the following unused global functions:
- e1000_hw.c: e1000_mc_addr_list_update
- e1000_hw.c: e1000_read_reg_io
- e1000_hw.c: e1000_enable_pciex_master
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes some needlessly global code static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device. If the module is unloaded, the module
text will be freed. Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device. If the module is unloaded, the module
text will be freed. Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Release code in driver modules is a potential cause of oopsen.
The device may be in use by a userspace process, which will keep
a reference to the device. If the module is unloaded, the module
text will be freed. Subsequently, when the last reference is
dropped, the release code will be called, which no longer exists.
Use generic platform device allocation/release code in modules.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds a phy_mask field to struct mii_bus and uses it. This field
indicates each phy address to be ignored when probing the mdio bus.
This support is needed for the fs_enet and ibm_emac drivers to be
converted to the generic phy layer among other drivers. Many systems
lock up on probing certain phy addresses or probing doesn't return
0xffff when nothing is found at the address. A new driver I'm
working on also makes use of this mask.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some boards using the 79c976 pcnet32 chip will hang the system if the
ethtool --register-dump is performed with the device operational. The
request to read bcr30 is retried by the PCI device infinitely without
returning data, hanging the system.
Tested ia32 and ppc64.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch is a better fix for Allied Telesyn 2700/2701 FX boards than
the change made in early January this year. It allows the user to
select the speed/duplex via module_param, but if no selection is made,
forces the speed to 100 FD. It fixes both Bugzilla bugs 2669 and 4551.
Tested ia32 and ppc64 by myself, and by the originator of bug 2669.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Display the name eth%d or pci_name() of device which fails to allocate
memory. When changing ring size via ethtool, it also releases the
lock before returning on error. Added comment that the caller of
pcnet32_alloc_ring must call pcnet32_free_ring on error, to avoid leak.
Tested ia32 by forcing allocation errors.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch provides dynamic two buffer-mode and 3 buffer-mode options.
Previously 2 buffer-mode was compilation option. Now with this patch applied
one can load driver in 2 buffer-mode with module-load parameter
ie.
#insmod s2io.ko rx_ring_mode=2
This patch also provides 3 buffer-mode which provides header separation
functionality. In 3 buffer-mode skb->data will have L2/L3/L4 headers and
"skb_shinfo(skb)->frag_list->data" will have have L4 payload.
one can load driver in 3 buffer-mode with same above module-load parameter
ie.
#insmod s2io.ko rx_ring_mode=3
Please review the patch.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
fid is declared as a u32 (unsigned int), and then a few lines later, it is checked for a value < 0, which is clearly useless.
In the two locations this function is used, in one it is *explicitly* given a negative number, which would be ignored with the
current definition.
Thanks to LinuxICC (http://linuxicc.sf.net).
Signed-off-by: Gabriel A. Devenyi <ace@staticwave.ca>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch fixes a panic in the current tree caused by a race condition between the initial replenish cycle and the rx processing of the first packets trying to replenish the buffers.
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Gone are the days when 8139too was a shining example of how to use
kernel threads. Delayed workqueues are easier, and map precisely to
our task: running code from a kernel thread, after a periodic sleep.
Convert most of the remaining "Using plain integer as NULL pointer" sparse
warnings to use NULL. (Not duplicating patches that are already in -mm,
-bird, or -kj.)
Convert isdn driver struct initializer to use C99 syntax.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Typo fix: dots appearing after a newline in printk strings.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed some more references to check_region().
I checked these changes into the 'checkreg' branch of
rsync://rsync.kernel.org/pub/scm/linux/kernel/git/jgarzik/misc-2.6.git
The only valid references remaining are in:
drivers/scsi/advansys.c
drivers/scsi/BusLogic.c
drivers/cdrom/sbpcd.c
sound/oss/pss.c
Remove last vestiges of ide_check_region()
drivers/char/specialix: trim trailing whitespace
drivers/char/specialix: eliminate use of check_region()
Remove outdated and unused references to check_region()
[sound oss] remove check_region() usage from cs4232, wavfront
[netdrvr eepro] trim trailing whitespace
[netdrvr eepro] remove check_region() usage
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
smsc-ircc2 - avoid closing network device when suspending; just release
interrupt and disable DMA ourselves. Also make sure to reset chip when
resuming.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Jean Tourrilhes <jt@bougret.hpl.hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update SMC91x driver for m32r.
- Remove needless NONCACHE_OFFSET adjustment.
> [PATCH 2.6.14-rc4] m32r: NONCACHE_OFFSET in _port2addr
> Change _port2addr() not to add NONCACHE_OFFSET.
> Adding NONCACHE_OFFSET requires needless address adjusting by a driver
> using ioremap() like a SMC91x driver.
- Fix lots of warnings as following:
/usr/src/ctest/git/kernel/drivers/net/smc91x.c: In function `smc_reset':
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:324: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:325: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:341: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:342: warning: passing arg 2 of `_outw' makes integer from pointer without a cast
:
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:1915: warning: passing arg 1 of `_inw' makes integer from pointer without a cast
/usr/src/ctest/git/kernel/drivers/net/smc91x.c:1915: warning: passing arg 1 of `_inw' makes integer from pointer without a cast
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Update the PXA irda driver to match the recent platform device
suspend/resume level changes.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch rewrites various occurences of &sg[0] where sg is an array
of length one to simply sg.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch uses sg_set_buf/sg_init_one in some places where it was
duplicated.
Signed-off-by: David Hardeman <david@2gen.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The following patch removes the dependency of the fec_8xx driver on
the NETTA & NETPHONE boards. Other people use the driver too, and
we await their board support patches.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The following patches fixes a bug with erroneous calling of
dma_unmap_single. It never triggered because on normal ppc32
the calls is a NOP. Out of tree drivers need this fix however.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
* MII registers must override strap pins
* disable "echo" mode to make 10/HDX work (Franz Sirl)
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
For some reason, the hardware designers made the polarity of one bit
in the 440SPe's PHY interface register the opposite of all other PPC
440 chips. To handle this, abstract our access to this bit and do the
right thing based on the configured CPU type.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The dev_kfree_skb in islpci_eth_transmit happens while irqs are still
disabled, so either dev_kfree_skb_irq needs to be used or the skb
needs to be freed after irqs have been enabled again. This patch
should fix it.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This one from my DMA_{32,64}BIT_MASK series did not seem to make it
through to upstream.
Use the DMA_{32,64}BIT_MASK constants from dma-mapping.h when calling
pci_set_dma_mask() or pci_set_consistent_dma_mask()
This patch includes dma-mapping.h explicitly because it caused errors
on some architectures otherwise.
See http://marc.theaimsgroup.com/?t=108001993000001&r=1&w=2 for details
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Added information message when using the SRAM in mv643xx_eth_probe()
Signed-off-by: Nicolas DET <det.nicolas@free.fr>
Signed-off-by: Sven Luther <sl@bplan-gmbh.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
mesh, mac53c94 and airport already have an entry. Add the network drivers
for pmac.
Signed-off-by: Olaf Hering <olh@suse.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
drivers/net/e1000/e1000_main.c:3645: warning: `e1000_suspend' defined
but not used
Signed-off-by: Ashutosh Naik <ashutosh_naik@adaptec.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
