The GLOBETROTTER.cis entry in serial_cs matches more devices than
intended and breaks them. Remove it.
Example: # pccardctl info
PRODID_1="Option International
"
PRODID_2="GSM-Ready 56K/ISDN
"
PRODID_3="021
"
PRODID_4="A
"
MANFID=0013,0000
FUNCID=0
result:
pcmcia 0.0: Direct firmware load for cis/GLOBETROTTER.cis failed with error -2
The GLOBETROTTER.cis is nowhere to be found. There's GLOBETROTTER.cis.ihex at
https://netdev.vger.kernel.narkive.com/h4inqdxM/patch-axnet-cs-fix-phy-id-detection-for-bogus-asix-chip#post41
It's from completely diffetent card:
vers_1 4.1, "Option International", "GSM/GPRS GlobeTrotter", "001", "A"
Signed-off-by: Ondrej Zary <linux@zary.sk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210611201940.23898-1-linux@zary.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle custom baud rates requested in the UPF_MAGIC_MULTIPLIER range
with BOTHER. Currently matching is exact, that is if a baud rate that
is not either of clk/4 or clk/8 is requested, then we fall through to
the default case, which will just divide the clock rate by 16 times the
rate requested, round it to closest integer, and possibly yield even
worse results then if clamping to the extra baud rates was chosen.
So for example if we have the usual base rate of 115200 and request a
rate of 230399, then the fall-through divisor calculation will yield 1,
and consequently the baud rate of 115200 will be programmed even though
obviously the magic rate of 230400 would be more appropriate.
Make the selection of the magic rates range-qualified then and use clk/4
for rates from clk/6 up (assuming `serial8250_get_baud_rate' has already
rejected any rates too far beyond clk/4), and otherwise use clk/8 for
rates from clk/12 up, and finally fall through to the standard divisor
calculation. Explicitly void using the undocumented rate of 153600bps
and stick to documented divisor values only.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2105200232090.29169@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for magic baud rate divisors of 32770 and 32769 used with SMSC
Super I/O chips for extra baud rates of 230400 and 460800 respectively
where base rate is 115200[1] has been added around Linux 2.5.64, which
predates our repo history, but the origin could be identified as commit
2a717aad772f ("Merge with Linux 2.5.64.") with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>.
Code that is now in `serial8250_do_get_divisor' was added back then to
`serial8250_get_divisor', but that code would only ever trigger if one
of the higher baud rates was actually requested, and that cannot ever
happen, because the earlier call to `serial8250_get_baud_rate' never
returns them. This is because it calls `uart_get_baud_rate' with the
maximum requested being the base rate, that is clk/16 or 115200 for SMSC
chips at their nominal clock rate.
Fix it then and allow UPF_MAGIC_MULTIPLIER baud rates to be selected, by
requesting the maximum baud rate of clk/4 rather than clk/16 if the flag
has been set. Also correct the minimum baud rate, observing that these
ports only support actual (non-magic) divisors of up to 32767 only.
References:
[1] "FDC37M81x, PC98/99 Compliant Enhanced Super I/O Controller with
Keyboard/Mouse Wake-Up", Standard Microsystems Corporation, Rev.
03/27/2000, Table 31 - "Baud Rates", p. 77
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2105190412280.29169@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Contrary to what SMSC documentation says and unlike NS16C550A UARTs the
SMSC Super I/O IC claims compatibility with the SMSC UART implementation
does not support dividing the internal PLL clock by any divisor from 1
to 65535[1], with the exception of two magic divisors of 32769 and 32770
used respectively to select the high-speed data rates of 460800bps and
230400bps[2] if enabled on a port-by-port basis in with the Serial Port
Mode Register in the Device Configuration Space[3][4].
Instead empirical evidence indicates that the divisor, as stored in the
DLL and DLM register pair, has the range of 1 to 32767 only, and bit 7
of the DLM register (bit 15 of the divisor) effectively serves as a
selection bit for the prescaler from the base frequency of 7.3728MHz,
either 4 if the bit is 0, or 1 if the bit is 1 and high-speed operation
has been enabled with the Serial Port Mode Register.
So if high-speed operation has not been enabled, then say the values of
1 and 32769 (0x8001) written into the combined DLL and DLM register pair
both select the divisor of 1 and the baud rate of 115200bps.
[1] "FDC37M81x, PC98/99 Compliant Enhanced Super I/O Controller with
Keyboard/Mouse Wake-Up", Standard Microsystems Corporation, Rev.
03/27/2000, Section "Programmable Baud Rate Generator (and Divisor
Latches DLH, DLL)", p. 75
[2] same, Table 31 - "Baud Rates", p. 77
[3] same, Table 60 - "Serial Port 1, Logical Device 4 [Logical Device
Number = 0x04]", p. 153
[4] same, Table 61 - "Serial Port 2, Logical Device 5 [Logical Device
Number = 0x05]", p. 153
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106092330530.5469@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oxford Semiconductor PCIe (Tornado) serial port devices are driven by a
fixed 62.5MHz clock input derived from the 100MHz PCI Express clock.
In the enhanced (650) mode, which we select in `autoconfig_has_efr' by
setting the ECB bit in the EFR register, and in the absence of clock
reconfiguration, which we currently don't do, the clock rate is divided
only by the oversampling rate of 16 as it is supplied to the baud rate
generator, yielding the baud base of 3906250. This comes from the reset
values of the TCR and MCR[7] registers which are both zero[1][2][3][4],
choosing the oversampling rate of 16 and the normal (divide by 1) baud
rate generator prescaler respectively. This is the rate that is divided
by the value held in the divisor latch to determine the baud rate used.
Replace the incorrect baud base of 4000000 with the right value of
3906250 then.
References:
[1] "OXPCIe200 PCI Express Multi-Port Bridge", Oxford Semiconductor,
Inc., DS-0045, 10 Nov 2008, Section "Reset Configuration", p. 72
[2] "OXPCIe952 PCI Express Bridge to Dual Serial & Parallel Port",
Oxford Semiconductor, Inc., DS-0046, Mar 06 08, Section "Reset
Configuration", p. 27
[3] "OXPCIe954 PCI Express Bridge to Quad Serial Port", Oxford
Semiconductor, Inc., DS-0047, Feb 08, Section "Reset Configuration",
p. 28
[4] "OXPCIe958 PCI Express Bridge to Octal Serial Port", Oxford
Semiconductor, Inc., DS-0048, Feb 08, Section "Reset Configuration",
p. 28
Fixes: 7106b4e333 ("8250: Oxford Semiconductor Devices")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106100203510.5469@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oxford Semiconductor PCIe (Tornado) serial port devices have their baud
base set incorrectly, however their `pciserial_board' entries have been
reused for Titan serial port devices. Define own entries for the latter
devices then, carrying over the settings, so that Oxford entries can be
fixed.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106100142310.5469@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the previous patch, we introduced tty_get_char_size() and
tty_get_frame_size() for computing character and frame sizes,
respectively. Here, we make use of them in various tty drivers where
applicable.
The stats look nice: 12 insertions, 169 deletions.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Oliver Neukum <oneukum@suse.com>
Acked-by: Alex Elder <elder@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's a bit illogical to take magic constants in AUART_LINECTRL_WLEN.
Like in auart_console_get_options(), 2 means 7 bits. Switch
AUART_LINECTRL_WLEN to accept bit length, i.e. let it subtract 5 from
the parameter before doing the logic.
This will ease conversion from CSIZE to bits in mxs_auart_settermios()
in the next patch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many tty drivers contain code to compute bits count depending on termios
cflags. So extract this code from serial core to two separate tty helper
functions:
* tty_get_char_size -- only size of a character, without flags,
* tty_get_frame_size -- complete size of a frame including flags.
In the next patch, calls to these new functions replace many copies of
this code.
Note that we accept only cflag as a parameter. That's because some
callers like pch_uart_startup or sunsab_console_setup don't have at hand
termios which we could pass around.
Cc: Joe Perches <joe@perches.com>
Cc: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Defer device probe operation when a DMA channel request probe deferral.
With this change both DMA channels are acquired before DMA channels are
configured. Once no probe deferral is expected, DMAs are
configured and any failure in their configuration will make the driver
to fallback to interrupt mode as prior this change.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Link: https://lore.kernel.org/r/20210610100020.2318-1-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Request the RX mailbox only after initializing the UART data
structures. Otherwise it can rarely happen that the receive
callback is called before the UART is ready.
Fixes: 2d908b38d4 ("serial: Add Tegra Combined UART driver")
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Link: https://lore.kernel.org/r/20210609155655.3567545-1-mperttunen@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop dmaengine transfer in sci_stop_tx(). Otherwise, the following
message is possible output when system enters suspend and while
transferring data, because clearing TIE bit in SCSCR is not able to
stop any dmaengine transfer.
sh-sci e6550000.serial: ttySC1: Unable to drain transmitter
Note that this driver has already used some #ifdef in the .c file
so that this patch also uses #ifdef to fix the issue. Otherwise,
build errors happens if the CONFIG_SERIAL_SH_SCI_DMA is disabled.
Fixes: 73a19e4c03 ("serial: sh-sci: Add DMA support.")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210610110806.277932-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into tty-next
We want the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We would like to use DMI matching in other functions as well.
Hence, extract it as exar_get_platform() helper function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210608144239.12697-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible that during ->exit() the private_data is NULL,
for instance when there was no GPIO device instantiated.
Due to this we may not dereference it. Add a respective check.
Note, for now ->exit() only makes sense when GPIO device
was instantiated, that's why we may use the check for entire
function.
Fixes: 81171e7d31 ("serial: 8250_exar: Constify the software nodes")
Reported-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Maxim Levitsky <mlevitsk@redhat.com>
Link: https://lore.kernel.org/r/20210608144239.12697-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add serial support for RZ/G2L SoC with earlycon and
extended mode register support.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210603221758.10305-11-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the hack to assign the global console_port variable at probe time.
This assumption that cons->index is -1 is wrong for systems that specify
'console=' in the cmdline (or 'stdout-path' in dts). Hence, on such system
the actual console assignment is ignored, and the first UART that happens
to be probed is used as console instead.
Move the logic to console_setup() and map the console to the correct port
through the array of available ports instead.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20210528133321.1859346-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to optimize serial communication (performance/throughput VS
latency), we may need to tweak DMA period number and size. This adds
DT properties to configure those values before initialising DMA.
The defaults will stay the same as before.
[update documentation and commit message, rebase to current master,
switch back to DT instead of sysfs]
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210430175038.103226-2-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small fixes for reported problems for tty and serial
drivers for 5.13-rc4.
They consist of:
- 8250 bugfixes and new device support
- lockdown security mode fixup
- syzbot found problems fixed
- 8250_omap fix for interrupt storm
- revert of 8250_omap driver fix as it caused worse problem than
the original issue
All but the last patch have been in linux-next for a while, the last one
is a revert of a problem found in linux-next with the 8250_omap driver
change.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYLJODQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yna7gCgmKIssymva29JpQb54HuzRooD8jcAn3XeMVWI
E4TQzaTFC1mNAQy8GU4F
=cLjq
-----END PGP SIGNATURE-----
Merge tag 'tty-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver fixes from Greg KH:
"Here are some small fixes for reported problems for tty and serial
drivers for 5.13-rc4.
They consist of:
- 8250 bugfixes and new device support
- lockdown security mode fixup
- syzbot found problems fixed
- 8250_omap fix for interrupt storm
- revert of 8250_omap driver fix as it caused worse problem than the
original issue
All but the last patch have been in linux-next for a while, the last
one is a revert of a problem found in linux-next with the 8250_omap
driver change"
* tag 'tty-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250: 8250_omap: Fix possible interrupt storm"
serial: 8250_pci: handle FL_NOIRQ board flag
serial: rp2: use 'request_firmware' instead of 'request_firmware_nowait'
serial: 8250_pci: Add support for new HPE serial device
serial: 8250: 8250_omap: Fix possible interrupt storm
serial: 8250: Use BIT(x) for UART_{CAP,BUG}_*
serial: 8250: Add UART_BUG_TXRACE workaround for Aspeed VUART
serial: 8250_dw: Add device HID for new AMD UART controller
serial: sh-sci: Fix off-by-one error in FIFO threshold register setting
serial: core: fix suspicious security_locked_down() call
serial: tegra: Fix a mask operation that is always true
This reverts commit 31fae7c8b1.
Tony writes:
I just noticed this causes the following regression in Linux
next when pressing a key on uart console after boot at least on
omap3. This seems to happen on serial_port_in(port, UART_RX) in
the quirk handling.
So let's drop this.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/YLCCJzkkB4N7LTQS@atomide.com
Fixes: 31fae7c8b1 ("serial: 8250: 8250_omap: Fix possible interrupt storm")
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 8428413b1d ("serial: 8250_pci: Implement MSI(-X) support")
the way the irq gets allocated was changed. With that change the
handling FL_NOIRQ got lost. Restore the old behaviour.
Fixes: 8428413b1d ("serial: 8250_pci: Implement MSI(-X) support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Link: https://lore.kernel.org/r/20210527095529.26281-1-christian.gmeiner@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for new HPE serial device. It is MSI enabled,
but otherwise similar to legacy HP server serial devices.
Tested-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Randy Wright <rwright@hpe.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1621009614-28836-1-git-send-email-rwright@hpe.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that RX TIMEOUT is signalled after RX FIFO has been
drained, in which case a dummy read of RX FIFO is required to clear RX
TIMEOUT condition. Otherwise, RX TIMEOUT condition is not cleared
leading to an interrupt storm
Cc: stable@vger.kernel.org
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210511151955.28071-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aspeed Virtual UARTs directly bridge e.g. the system console UART on the
LPC bus to the UART interface on the BMC's internal APB. As such there's
no RS-232 signalling involved - the UART interfaces on each bus are
directly connected as the producers and consumers of the one set of
FIFOs.
The APB in the AST2600 generally runs at 100MHz while the LPC bus peaks
at 33MHz. The difference in clock speeds exposes a race in the VUART
design where a Tx data burst on the APB interface can result in a byte
lost on the LPC interface. The symptom is LSR[DR] remains clear on the
LPC interface despite data being present in its Rx FIFO, while LSR[THRE]
remains clear on the APB interface as the host has not consumed the data
the BMC has transmitted. In this state, the UART has stalled and no
further data can be transmitted without manual intervention (e.g.
resetting the FIFOs, resulting in loss of data).
The recommended work-around is to insert a read cycle on the APB
interface between writes to THR.
Cc: ChiaWei Wang <chiawei_wang@aspeedtech.com>
Tested-by: ChiaWei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210520021334.497341-2-andrew@aj.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/st-asc.c:73: warning: expecting prototype for Some of status comes from higher bits of the character and some come from(). Prototype was for ASC_RXBUF_DUMMY_RX() instead
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210520121906.3468725-10-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the previous patch, we can make port passed to
serial8250_find_match_or_unused const. And then we can make const also
port of serial8250_register_8250_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210519072153.3859-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* make parameters const (as they are only read)
* return bool (as comparison results are returned)
* add \n before final return
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210519072153.3859-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most litex boards using RISC-V soft cores us the sbi earlycon, however
this is not available for non RISC-V litex SoC's. This patch enables
earlycon for liteuart which is available on all Litex SoC's making
support for earycon debugging more widely available.
Cc: Florent Kermarrec <florent@enjoy-digital.fr>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Gabriel L. Somlo <gsomlo@gmail.com>
Reviewed-and-tested-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Link: https://lore.kernel.org/r/20210517115453.24365-1-shorne@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some configurations, mainly ACPI-based, the clock frequency of the device
is supplied by very well established 'clock-frequency' property. Hence, try
to get it from the property at last if no other providers are available.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210517172930.83353-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to initialise irq-flags variables before saving the
interrupt state.
Drop the redundant initialisations from drivers that got this wrong.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210519092541.10137-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable c is being initialized with a value that is never
read, it is being updated later on. The assignment is redundant and
can be removed.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/r/20210513230224.138859-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add serial support for RZ/G2L SoC with earlycon and
extended mode register support.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210514192218.13022-11-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the DT bindings has a property to get the FIFO size for a particular port,
retrieve it and use to setup the FIFO interrupts threshold.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210518075833.3736038-3-narmstrong@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include the more general linux/io.h instead of asm/io.h
as checkpatch suggests.
Signed-off-by: Zihao Tang <tangzihao1@hisilicon.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1620874904-39285-13-git-send-email-f.fangjian@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include the more general linux/io.h instead of asm/io.h
as checkpatch suggests.
Signed-off-by: Zihao Tang <tangzihao1@hisilicon.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1620874904-39285-12-git-send-email-f.fangjian@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include the more general linux/io.h instead of asm/io.h
as checkpatch suggests.
Signed-off-by: Zihao Tang <tangzihao1@hisilicon.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1620874904-39285-11-git-send-email-f.fangjian@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include the more general linux/io.h instead of asm/io.h
as checkpatch suggests.
Signed-off-by: Zihao Tang <tangzihao1@hisilicon.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1620874904-39285-10-git-send-email-f.fangjian@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include the more general linux/io.h instead of asm/io.h
as checkpatch suggests.
Signed-off-by: Zihao Tang <tangzihao1@hisilicon.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1620874904-39285-9-git-send-email-f.fangjian@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include the more general linux/io.h instead of asm/io.h
as checkpatch suggests.
Signed-off-by: Zihao Tang <tangzihao1@hisilicon.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1620874904-39285-8-git-send-email-f.fangjian@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include the more general linux/io.h instead of asm/io.h
as checkpatch suggests.
Signed-off-by: Zihao Tang <tangzihao1@hisilicon.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1620874904-39285-7-git-send-email-f.fangjian@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Include the more general linux/io.h instead of asm/io.h
as checkpatch suggests.
Signed-off-by: Zihao Tang <tangzihao1@hisilicon.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1620874904-39285-6-git-send-email-f.fangjian@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
