The Flash Interface Unit (FIU) is the SPI flash controller in the
Nuvoton WPCM450 BMC SoC. It supports four chip selects, and direct
(memory-mapped) access to 16 MiB per chip. Larger flash chips can be
accessed by software-defined SPI transfers.
The FIU in newer NPCM7xx SoCs is not compatible with the WPCM450 FIU.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20221124191400.287918-3-j.neuschaefer@gmx.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce Socionext F_OSPI controller driver. This controller is used to
communicate with slave devices such as SPI Flash memories. It supports
4 slave devices and up to 8-bit wide bus, but supports master mode only.
This driver uses spi-mem framework for SPI flash memory access, and
can only operate indirect access mode and single data rate mode.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20221124003351.7792-3-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Microchip pci1xxxx is a PCIe switch with a multi-function endpoint on one of its
downstream ports. SPI is one of the functions in the multi-function endpoint. This
function has 2 SPI masters, operates at a maximum frequency of 30 MHz and supports
7 client devices per master. This patch adds complete functionality to the SPI
function except for suspend and resume.
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Link: https://lore.kernel.org/r/20221006050514.115564-2-tharunkumar.pasumarthi@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a driver for Microchip FPGA QSPI controllers. This driver also
supports "hard" QSPI controllers on Polarfire SoC.
Signed-off-by: Naga Sureshkumar Relli <nagasuresh.relli@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220808064603.1174906-4-nagasuresh.relli@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The GXP supports 3 separate SPI interfaces to accommodate the system
flash, core flash, and other functions. The SPI engine supports variable
clock frequency, selectable 3-byte or 4-byte addressing and a
configurable x1, x2, and x4 command/address/data modes. The memory
buffer for reading and writing ranges between 256 bytes and 8KB. This
driver supports access to the core flash and bios part.
Signed-off-by: Nick Hawkins <nick.hawkins@hpe.com>
Link: https://lore.kernel.org/r/20220728161459.7738-2-nick.hawkins@hpe.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This SPI driver adds support for the Aspeed static memory controllers
of the AST2600, AST2500 and AST2400 SoCs using the spi-mem interface.
* AST2600 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. Only supports SPI type flash memory
. different segment register interface
. single, dual and quad mode.
* AST2600 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. different segment register interface
. single, dual and quad mode.
* AST2500 Firmware SPI Memory Controller (FMC)
. BMC firmware
. 3 chip select pins (CE0 ~ CE2)
. supports SPI type flash memory (CE0-CE1)
. CE2 can be of NOR type flash but this is not supported by the driver
. single, dual mode.
* AST2500 SPI Flash Controller (SPI1 and SPI2)
. host firmware
. 2 chip select pins (CE0 ~ CE1)
. single, dual mode.
* AST2400 New Static Memory Controller (also referred as FMC)
. BMC firmware
. New register set
. 5 chip select pins (CE0 ∼ CE4)
. supports NOR flash, NAND flash and SPI flash memory.
. single, dual and quad mode.
Each controller has a memory range on which flash devices contents are
mapped. Each device is assigned a window that can be changed at bootime
with the Segment Address Registers.
Each SPI flash device can then be accessed in two modes: Command and
User. When in User mode, SPI transfers are initiated with accesses to
the memory segment of a device. When in Command mode, memory
operations on the memory segment of a device generate SPI commands
automatically using a Control Register for the settings.
This initial patch adds support for User mode. Command mode needs a little
more work to check that the memory window on the AHB bus fits the device
size. It will come later when support for direct mapping is added.
Single and dual mode RX transfers are supported. Other types than SPI
are not supported.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Tao Ren <rentao.bupt@gmail.com>
Tested-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Link: https://lore.kernel.org/r/20220509175616.1089346-4-clg@kaod.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver implements support for the SPI-NAND mode of MTK NAND Flash
Interface as a SPI-MEM controller with pipelined ECC capability.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20220424032527.673605-3-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Mika Westerberg <mika.westerberg@linux.intel.com>:
Based on discussion on the patch I sent some time ago here:
http://lists.infradead.org/pipermail/linux-mtd/2021-June/086867.html
it turns out that the preferred way to deal with the SPI flash controller
drivers is through SPI MEM which is part of Linux SPI subsystem.
This series does that for the intel-spi driver. This also renames the
driver to follow the convention used in the SPI subsystem. The first patch
improves the write protection handling to be slightly more safer. The
following two patches do the conversion itself. Note the Intel SPI flash
controller only allows commands such as read, write and so on and it
internally uses whatever addressing etc. it figured from the SFDP on the
flash device.
base-commit: e783362eb5
The preferred way to implement SPI-NOR controller drivers is through SPI
subsubsystem utilizing the SPI MEM core functions. This converts the
Intel SPI flash controller driver over the SPI MEM by moving the driver
from SPI-NOR subsystem to SPI subsystem and in one go make it use the
SPI MEM functions. The driver name will be changed from intel-spi to
spi-intel to match the convention used in the SPI subsystem.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mauro Lima <mauro.lima@eclypsium.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220209122706.42439-3-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds driver for Cadence's XSPI controller.
It supports 3 work modes.
1. ACMD (auto command) work mode
ACMD name is because it uses auto command engine in the controller.
It further has 2 modes PIO and CDMA (command DMA).
The CDMA work mode is dedicated for high-performance application
where very low software overhead is required. In this mode the
Command Engine is programmed by the series of linked descriptors
stored in system memory. These descriptors provide commands to execute
and store status information for finished commands.
The PIO mode work mode is dedicated for single operation where
constructing a linked list of descriptors would require too
much effort.
2. STIG (Software Triggered Instruction Generator) work mode
In STIG mode, controller sends low-level instructions to memory.
Each instruction is 128-bit width. There is special instruction
DataSequence which carries information about data phase.
Driver uses Slave DMA interface to transfer data as only this
interface can be used in STIG work mode.
3. Direct work mode
This work mode allows sending data without invoking any command through
the slave interface.
Currently only STIG work mode is enabled, remaining work modes will
be added later.
Signed-off-by: Konrad Kociolek <konrad@cadence.com>
Signed-off-by: Jayshri Pawar <jpawar@cadence.com>
Signed-off-by: Parshuram Thombare <pthombar@cadence.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/1632038734-23999-1-git-send-email-pthombar@cadence.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a driver to support the SPI controller found in Ingenic SoCs.
Co-developed-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Link: https://lore.kernel.org/r/20210830230139.21476-3-contact@artur-rojek.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the rockchip serial flash controller (SFC) driver.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20210812134546.31340-3-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a Device Feature List (DFL) bus driver for the
Altera SPI Master controller. The SPI master is connected to an
Intel SPI Slave to Avalon Bridge inside an Intel MAX10
BMC Chip.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Link: https://lore.kernel.org/r/20210416165720.554144-3-matthew.gerlach@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver supports SPI Controller for HiSilicon Kunpeng SoCs. This
driver supports SPI operations using FIFO mode of transfer.
DMA is not supported, and we just use IRQ mode for operation completion
notification.
Only ACPI firmware is supported.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1616836200-45827-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver likely also supports earlier (RTL8196) and later (RTL93xx)
SoCs.
The SPI hardware in these SoCs is specifically intended for connecting NOR
bootflash chips, and only used for that in dozens of examined devices.
However boiled down to basics, it's really just a half-duplex SPI
controller.
The hardware appears to have a vestigial second chip-select control, but
it hasn't been seen in the wild and is thus not supported.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Link: https://lore.kernel.org/r/20210120135928.246054-3-bert@biot.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <baohua@kernel.org>
Link: https://lore.kernel.org/r/20210120161658.3820610-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
Baikal-T1 is equipped with three DW APB SSI-based MMIO SPI controllers.
Two of them are pretty much normal: with IRQ, DMA, FIFOs of 64 words
depth, 4x CSs, but the third one as being a part of the Baikal-T1 System
Boot Controller has got a very limited resources: no IRQ, no DMA, only a
single native chip-select and Tx/Rx FIFO with just 8 words depth
available. In order to provide a transparent initial boot code execution
the Boot SPI controller is also utilized by an vendor-specific IP-block,
which exposes an SPI flash direct mapping interface. Since both direct
mapping and SPI controller normal utilization are mutual exclusive only
one of these interfaces can be used to access an external SPI slave
device. That's why a dedicated mux is embedded into the System Boot
Controller. All of that is taken into account in the Baikal-T1-specific DW
APB SSI glue driver implemented by means of the DW SPI core module.
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20201007235511.4935-22-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
The fiq handler needs access to some register definitions that
should not be used directly by device drivers.
Since this is closely related to the irqchip driver anyway,
move it into the same place.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[krzk: Add a header guard in include/linux/spi/s3c24xx-fiq.h, fix
SPDX comment style, update maintainer's entry]
Co-developed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-23-krzk%40kernel.org
Acked-by: Mark Brown <broonie@kernel.org>
This series is a subset of "[PATCH v12 0/4] spi: cadence-quadspi: Add
support for the Cadence QSPI controller" by Ramuthevar,Vadivel MuruganX
<vadivel.muruganx.ramuthevar@linux.intel.com> that intended to move
cadence-quadspi driver to spi-mem framework
Those patches were trying to accomplish too many things in a single set
of patches and need to split into smaller patches. This is reduced
version of above series.
Changes that are intended to make migration easy are split into separate
patches. Patches 1 to 3 drop features that cannot be supported under
spi-mem at the moment (backward compatibility is maintained).
Patch 4-5 are trivial cleanups. Patch 6 does the actual conversion to
spi-mem and patch 7 moves the driver to drivers/spi folder.
I have tested both INDAC mode (used by non TI platforms like Altera
SoCFPGA) and DAC mode (used by TI platforms) on TI EVMs.
Patches to move move bindings over to
"Documentation/devicetree/bindings/spi/" directory and also conversion
of bindig doc to YAML will be posted separately. Support for Intel
platform would follow that.
Resend v3:
Rebased onto v5.7-c1
v3:
Split handling of probe deferral into separate patch (out of 5/6)
Split dropping of redundant WREN to separate patch (out of 5/6)
Fix a possible memleak due to lack of spi_master_put()
Parse all SPI slave nodes in cqspi_setup_flash()
Address misc comments from Tudor on v2
Rebase onto latest spi-nor/next
v2:
Rework patch 1/6 to keep "cdns,is-decoded-cs" property supported.
Ramuthevar Vadivel Murugan (2):
mtd: spi-nor: Convert cadence-quadspi to use spi-mem framework
spi: Move cadence-quadspi driver to drivers/spi/
Vignesh Raghavendra (6):
mtd: spi-nor: cadence-quadspi: Make driver independent of flash
geometry
mtd: spi-nor: cadence-quadspi: Provide a way to disable DAC mode
mtd: spi-nor: cadence-quadspi: Don't initialize rx_dma_complete on
failure
mtd: spi-nor: cadence-quadspi: Fix error path on failure to acquire
reset lines
mtd: spi-nor: cadence-quadspi: Handle probe deferral while requesting
DMA channel
mtd: spi-nor: cadence-quadspi: Drop redundant WREN in erase path
drivers/mtd/spi-nor/controllers/Kconfig | 11 -
drivers/mtd/spi-nor/controllers/Makefile | 1 -
drivers/spi/Kconfig | 11 +
drivers/spi/Makefile | 1 +
.../spi-cadence-quadspi.c} | 541 +++++++-----------
5 files changed, 222 insertions(+), 343 deletions(-)
rename drivers/{mtd/spi-nor/controllers/cadence-quadspi.c => spi/spi-cadence-quadspi.c} (74%)
base-commit: b3a9e3b962
--
2.26.2
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
Now that cadence-quadspi has been converted to use spi-mem framework,
move it under drivers/spi/
Update license header to match SPI subsystem style
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200601070444.16923-9-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the SPI driver for the Renesas RPC-IF. It's the "front end" driver
using the "back end" APIs in the main driver to talk to the real hardware.
We only implement the 'spi-mem' interface -- there's no need to implement
the usual SPI driver methods...
Based on the original patch by Mason Yang <masonccyang@mxic.com.tw>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Link: https://lore.kernel.org/r/1ece0e6c-71af-f0f1-709e-571f4b0b4853@cogentembedded.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a preparation patch before adding the DW DMA support into the
DW SPI MMIO driver. We need to unpin the Non-DMA-specific code from the
intended to be generic DW APB SSI DMA code. This isn't that hard,
since the most part of the spi-dw-mid.c driver in fact implements a
generic DMA interface for the DW SPI controller driver. The only Intel
MID specifics concern getting the max frequency from the MRST Clock
Control Unit and fetching the DMA controller channels from
corresponding PCIe DMA controller. Since first one is related with the
SPI interface configuration we moved it' implementation into the
DW PCIe-SPI driver module. After that former spi-dw-mid.c file
can be just renamed to be the DW SPI DMA module optionally compiled in to
the DW APB SSI core driver.
Co-developed-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Co-developed-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Signed-off-by: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-11-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Generic DMA support is going to be part of the DW APB SSI core object.
In order to preserve the kernel loadable module name as spi-dw.ko, let's
add the "-core" suffix to the object with generic DW APB SSI code and
build it into the target spi-dw.ko driver.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru>
Cc: Ramil Zaripov <Ramil.Zaripov@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Link: https://lore.kernel.org/r/20200529131205.31838-10-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver supports SPI Controller for AMD SOCs.This driver
supports SPI operations using FIFO mode of transfer.
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/1587844788-33997-1-git-send-email-sanju.mehta@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patchset from Chuanhong Guo <gch981213@gmail.com> adds a spi-mem
driver for Mediatek SPI-NOR controller, which already has limited
support by mtk-quadspi. This new driver can make use of full quadspi
capability of this controller.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl5pQmYTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0D9sB/9PBy5hYIWLJOqP3Tegy+si7eEjgYQe
32DvHZRYYL+Oc8OQMGnJYUY5grfriS300TjxeB4MNx8ajVyuaH7e2aIhgTz3oJ6a
YrygFcxEi0LmRT82HyLVxptyblMSo3A8QWOTOqe1aFvJRZjDDKvEIcGCW2RPmtxT
r/EoVVkSv4X+k3GUtYnRBrq12hL+vr1YIjZM05MVu2sDtFXLO2+wotFIODDv15zi
ByBtwhKumKawUOETzGDw4EDV5MJx9nZtswRC4x3hDrLS6au39F/MyP78gpHm8vw+
YfiS5/39rkB6j1QltcP3B9n7joxrgaFAYsLBTZUoE3IjeVTggcKCOSVX
=q5ml
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl5pQt4THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0BFqB/9jBg5bNy9mNXljELZ7RKCtbn9CThYk
NvccckUJnjaTxSccGcGEetfFtoVvM4IJ8ffiL6gBrNDgvuSbedLkboqlftRRbkE2
tvxnfjKGeiVIHXcXG0kzrVMDPPncYy+o8nQMJ8b/v+VFeLah6LCo0nT4t54LPvfZ
52Nncdr8jAnjoet7t2CX2nJrhTOPUGhC7HxbwOyu2HOOd5nWmYAdT4UZo4Vdv1g9
L1knLoZctpvCpql/mUWdOAqQbD0bD0vT3FKQaq6C6kAeE+kMWSGdPgYxyFdBEVXi
uOmaqU7lHt2bsr6TRbOpw4ON0PzQtzZ/YhW2XEPJd6uc3GWy//qEyqgO
=qoqi
-----END PGP SIGNATURE-----
Merge tag 'mtk-mtd-spi-move' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into spi-5.7
spi: Rewrite mtk-quadspi spi-nor driver with spi-mem
This patchset from Chuanhong Guo <gch981213@gmail.com> adds a spi-mem
driver for Mediatek SPI-NOR controller, which already has limited
support by mtk-quadspi. This new driver can make use of full quadspi
capability of this controller.
This is a driver for mtk spi-nor controller using spi-mem interface.
The same controller already has limited support provided by mtk-quadspi
driver under spi-nor framework and this new driver is a replacement
for the old one.
Comparing to the old driver, this driver has following advantages:
1. It can handle any full-duplex spi transfer up to 6 bytes, and
this is implemented using generic spi interface.
2. It take account into command opcode properly. The reading routine
in this controller can only use 0x03 or 0x0b as opcode on 1-1-1
transfers, but old driver doesn't implement this properly. This
driver checks supported opcode explicitly and use (1) to perform
unmatched operations.
3. It properly handles SFDP reading. Old driver can't read SFDP
due to the bug mentioned in (2).
4. It can do 1-2-2 and 1-4-4 fast reading on spi-nor. These two ops
requires parsing SFDP, which isn't possible in old driver. And
the old driver is only flagged to support 1-1-2 mode.
5. It takes advantage of the DMA feature in this controller for
long reads and supports IRQ on DMA requests to free cpu cycles
from polling status registers on long DMA reading. It achieves
up to 17.5MB/s reading speed (1-4-4 mode) which is way faster
than the old one. IRQ is implemented as optional to maintain
backward compatibility.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200306085052.28258-3-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There exists a set of SPI controllers on some POWER processors that may
be accessed through the FSI bus. Add a driver to traverse the FSI CFAM
engine that can access and drive the SPI controllers. This driver would
typically be used by a baseboard management controller (BMC).
The SPI controllers operate by means of programming a sequencing engine
which automatically manages the usual SPI protocol buses. The driver
programs each transfer into the sequencer as various operations
specifying the slave chip and shifting data in and out on the lines.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20200306194118.18581-3-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a SPI device driver that sits in-band and provides a SPI controller
which supports chip selects via a mux-control. This enables extra SPI
devices to be connected with limited native chip selects.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200204032838.20739-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds driver for SPI controller found in Qualcomm Atheros
AR934x/QCA95xx SoCs.
This controller is a superset of the already supported qca,ar7100-spi.
Besides the bit-bang mode in spi-ath79.c, this new controller added
a new "shift register" mode, allowing faster spi operations.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/20200210034152.49063-2-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the driver for the HiSilicon v3xx SPI NOR flash controller, commonly
found in hi16xx chipsets.
This is a different controller than that in drivers/mtd/spi-nor/hisi-sfc.c;
indeed, the naming for that driver is poor, since it is really known as
FMC, and can support other memory technologies.
The driver module name is "hisi-sfc-v3xx", as recommended by HW designer,
being an attempt to provide a distinct name - v3xx being the unique
controller versioning.
Only ACPI firmware is supported.
DMA is not supported, and we just use polling mode for operation
completion notification.
The driver uses the SPI MEM OPs.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1575900490-74467-3-git-send-email-john.garry@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The branch contains driver changes that are tightly
connected to SoC specific code. Aside from smaller
cleanups and bug fixes, here is a list of the notable
changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver
for its on-board pluggable extension bus. The
same platform also gains a firmware driver.
- The Samsung Exynos family gains a new Chipid driver
exporting using the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon
chips.
- A firmware driver for the NXP i.MX DSP IPC protocol
using shared memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the
NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for
the S905X3 and A311D chips
- A rework of the TI Davinci framebuffer driver to
allow important cleanups in the platform code
- A couple of device drivers for removed ARM SoC
platforms are removed. Most of the removals were
picked up by other maintainers, this contains
whatever was left.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lxFi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This contains driver changes that are tightly connected to SoC
specific code. Aside from smaller cleanups and bug fixes, here is a
list of the notable changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver for its
on-board pluggable extension bus. The same platform also gains a
firmware driver.
- The Samsung Exynos family gains a new Chipid driver exporting using
the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon chips.
- A firmware driver for the NXP i.MX DSP IPC protocol using shared
memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for the S905X3 and A311D
chips
- A rework of the TI Davinci framebuffer driver to allow important
cleanups in the platform code
- A couple of device drivers for removed ARM SoC platforms are
removed. Most of the removals were picked up by other maintainers,
this contains whatever was left"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
bus: uniphier-system-bus: use devm_platform_ioremap_resource()
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
bus: imx-weim: remove incorrect __init annotations
fbdev: remove w90x900/nuc900 platform drivers
spi: remove w90x900 driver
net: remove w90p910-ether driver
net: remove ks8695 driver
firmware: turris-mox-rwtm: Add sysfs documentation
firmware: Add Turris Mox rWTM firmware driver
dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
bus: moxtet: fix unsigned comparison to less than zero
bus: moxtet: remove set but not used variable 'dummy'
ARM: scoop: Use the right include
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
...
The ARM w90x900 platform is getting removed, so this driver is obsolete.
Link: https://lore.kernel.org/r/20190809202749.742267-8-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add Nuvoton NPCM BMC Flash Interface Unit(FIU) SPI master
controller driver using SPI-MEM interface.
The FIU supports single, dual or quad communication interface.
the FIU controller can operate in following modes:
- User Mode Access(UMA): provides flash access by using an
indirect address/data mechanism.
- direct rd/wr mode: maps the flash memory into the core
address space.
- SPI-X mode: used for an expansion bus to an ASIC or CPLD.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/20190828142513.228556-3-tmaimon77@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for controller found on synquacer platforms.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for QSPI controller driver used by Xilinx Zynq SOC.
Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch moves the MT7621 SPI driver, which is used on some Ralink /
MediaTek MT76xx MIPS SoC's, out of the staging directory. No changes to
the source code are done in this patch.
This driver version was tested successfully on an MT7688 based platform
with an SPI NOR on CS0 and an SPI NAND on CS1 without any issues (so
far).
This patch also documents the devicetree bindings for the MT7621 SPI
device driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: NeilBrown <neil@brown.name>
Cc: Sankalp Negi <sankalpnegi2310@gmail.com>
Cc: Chuanhong Guo <gch981213@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: Armando Miraglia <arma2ff0@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add driver for the SiFive SPI controller
on the HiFive Unleashed board.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Add driver for NXP FlexSPI host controller
(0) What is the FlexSPI controller?
FlexSPI is a flexsible SPI host controller which supports two SPI
channels and up to 4 external devices. Each channel supports
Single/Dual/Quad/Octal mode data transfer (1/2/4/8 bidirectional
data lines) i.e. FlexSPI acts as an interface to external devices,
maximum 4, each with up to 8 bidirectional data lines.
It uses new SPI memory interface of the SPI framework to issue
flash memory operations to up to four connected flash
devices (2 buses with 2 CS each).
(1) Tested this driver with the mtd_debug and JFFS2 filesystem utility
on NXP LX2160ARDB and LX2160AQDS targets.
LX2160ARDB is having two NOR slave device connected on single bus A
i.e. A0 and A1 (CS0 and CS1).
LX2160AQDS is having two NOR slave device connected on separate buses
one flash on A0 and second on B1 i.e. (CS0 and CS3).
Verified this driver on following SPI NOR flashes:
Micron, mt35xu512ab, [Read - 1 bit mode]
Cypress, s25fl512s, [Read - 1/2/4 bit mode]
Signed-off-by: Yogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Tested-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is derived from the SPI NOR driver at
mtd/spi-nor/fsl-quadspi.c. It uses the new SPI memory interface
of the SPI framework to issue flash memory operations to up to
four connected flash chips (2 buses with 2 CS each).
The controller does not support generic SPI messages.
This patch also disables the build of the "old" driver and reuses
its Kconfig option CONFIG_SPI_FSL_QUADSPI to replace it.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Tested-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Tested-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kernel contains QSPI driver strongly tied to MTD and nor-flash memory.
New spi-mem interface allows usage also other memory types, especially
much larger NAND with SPI interface. This driver works as SPI controller
and is not related to MTD, however can work with NAND-flash or other
peripherals using spi-mem interface.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Piotr Bugalski <bugalski.piotr@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
