This keyboard emits a few usages that are not handled properly by
hid-input.
The usages from MSVENDOR page are colliding with Chicony Tactical
Pad device, so we have to distinguish in runtime. Ugly ...
Also, the buttons 1-5 have to be handled in a non-standard way,
as they are emitted by the keyboard in a bitfield-like fashion, but
the field is not presented as bit-field by the keyboard. The keys can't
be pressed simultaneously, so the handling we have is correct.
This patch also extends hid_keyboard[] with KPLeftParenthesis and
KPRightParenthesis as defined by Keyboard page in HUT 1.12. The
corresponding usages are also emitted by this keyboard.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix the following warning:
drivers/mtd/ubi/eba.c: In function 'ubi_eba_init_scan':
drivers/mtd/ubi/eba.c:1116: warning: 'err' may be used uninitialized in this function
Pointed-to-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When the UBI device is nearly full, i.e. all LEBs are mapped, we have
only one spare LEB left - the one we reserved for WL purposes. Well,
I do not count the LEBs which were reserved for bad PEB handling -
suppose NOR flash for simplicity. If an "atomic LEB change operation"
is run, and the WL unit is moving a LEB, we have no spare LEBs to
finish the operation and fail, which is not good. Moreover, if there
are 2 or more simultanious "atomic LEB change" requests, only one of
them has chances to succeed, the other will fail with -ENOSPC. Not
good either.
This patch does 2 things:
1. Reserves one PEB for the "atomic LEB change" operation.
2. Serealize the operations so that only on of them may run
at a time (by means of a mutex).
Pointed-to-by: Brijesh Singh <brijesh.s.singh@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Similar reason as in case of the previous patch: it causes
deadlocks if a filesystem with writeback support works on top
of UBI. So pre-allocate needed buffers when attaching MTD device.
We also need mutexes to protect the buffers, but they do not
cause much contantion because they are used in recovery, torture,
and WL copy routines, which are called seldom.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Use GFP_NOFS flag when allocating memory on I/O path, because otherwise
we may deadlock the filesystem which works on top of us. We observed
the deadlocks with UBIFS. Example:
VFS->FS lock a lock->UBI->kmalloc()->VFS writeback->FS locks the same
lock again.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
I can't find anything guaranteeing that 'ubi_num' cannot be <0 in
drivers/mtd/ubi/kapi.c::ubi_open_volume(), and in fact the code
even tests for that and errors out if so. Unfortunately the test
for "ubi_num < 0" happens after we've already used 'ubi_num' as
an array index - bad thing to do if it is negative.
This patch moves the test earlier in the function and then moves
the indexing using that variable after the check. A bit safer :-)
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
I hit those situations and found out lack of print messages. Add more prints
when erase problems occur.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Fix "symbol shadows an earlier one" warnings. Although they are harmless
but it does not hurt to fix them and make sparse happy.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Coverity (1769) found the following problem: if the erase counter
overflow check triggers, ec_hdr is leaked.
Moving the allocation after the overflow check should take care of it.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch cleans up the driver a bit. It contains
coding style fixes (pointed by Lindent and checkpatch)
and white space clean ups.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds accelerated copyarea and sets READS_FAST flag.
This doubles scrolling speed on SparcStation20 85MHz.
It also fixes a comment in cg6_fillrect function.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch:
- corrects coding style errors pointed by Lindent and checkpatch
- replaces space chunks with tabs
- removes one redundant include
- improves indentations of defines
- removes from comments leftovers from skeletonfb
- adds __devinit attribute to two init functions
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
ohci_bus_{suspend,resume} exists only if we have CONFIG_PM; do the same
thing as other subdrivers...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The bank switching code assumes that the bank selector is set to 0
when the driver is loaded. This might not be the case. This is exactly
the same bug as was fixed in the w83627ehf driver two months ago:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=0956895aa6f8dc6a33210967252fd7787652537d
In practice, this bug was causing the sensor thermal types to be
improperly reported for my W83627THF the first time I was loading the
w83627hf driver. From the driver history, I'd say that it has been
broken since September 2005 (when we stopped resetting the chip by
default at driver load.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch is to add an abort function that will bring back the MCP51/55
controller if it was blocked by a block-read operation, in particular.
(When a slave sends a wrong byte count on a byte read, the host gets
locked up). I've only tested it on an MCP51 and MCP55. However, I'm
almost certain it will also work on MCP65, I just did not have the board
to test it on. Thus for now the abort function will only be called
if an MCP51/55 was detected.
Signed-off-by: Oleg Ryjkov <olegr@olegr.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is the first part of the patch that adds a function to reset the
nvidia MCP51/55 i2c controller, if something bad happens to it (e.g.
a slave sends a wrong byte count during a block transaction).
This patch just adds nforce2_check_status function. It was originally
written by Hans-Frieder Vogt.
The reason that I'm the one sending it is:
- I relied on it for the second part of the patch,
- It makes the driver code cleaner/better.
Signed-off-by: Oleg Ryjkov <olegr@olegr.ca>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix a "mis-used register" problem on the AMD MIPS Alchemy au1550
I2C interface.
In summary, the programmable serial controller seems to hang the kernel
when I send a single 'address' byte on the I2C bus. The patch
essentially uses the PSC_SMBSTAT register's TE (transmit FIFO empty)
bit to check when the transmit FIFO is empty, instead of using the
PSC_SMBEVNT register's TU (transmit underflow) bit. Using the TE bit
fixed the hang problem.
Signed-off-by: Chris David <cd@chrisdavid.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Rename I2C_FUNC_SMBUS_HWPEC_CALC as I2C_FUNC_SMBUS_PEC, and list that
functionality as always available through the software implementation.
Update documentation accordingly (and list similar requirements).
The way it's currently packaged doesn't present the capability in a
useful way.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Mark the i2c-at91 driver BROKEN in Kconfig, and explain just
why it's broken. (Summary: hardware design issues.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This removes:
- An effectively unused hook: i2c_algorithm.algo_control.
- The i2c_control() call, used only by i2c-dev to call that
unused hook or set two barely supported adapter params.
(That param setting moves into i2c-dev.c ... still iffy
due to lack of locking, but no other changes.)
As shown by diffstat, this is a net code shrink. It also reduces the
complexity of the I2C adapter and /dev interfaces.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c_algorithm.algo_control is about to be removed.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This removes NOP implementations of i2c_algorithm.algo_control.
With this change, there are no implementations of this hook in
the kernel.org tree ... that hook seems about ripe to remove.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The I2C_M_RECV_LEN calling convention for i2c_mesg.flags involves
playing games with reported buffer lengths. (They start out less
than their actual size, and the length is then modified to reflect
how many bytes were delivered ... which one hopes is less than the
presumed actual size.) Refuse to play such error prone games across
the boundary between userspace and kernel.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for multiple chips to i2c-stub. I've changed the memory
allocation scheme from static to dynamic, so that we don't waste too
much memory.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mark M. Hoffman <mhoffman@lightlink.com>
Remove this unneeded mutex. Indeed it was used to serialize access to
the hardware, but this is already done by the i2c-core layer, see
'bus_lock' mutex used by i2c_transfer().
Signed-off-by: Francis Moreau <francis.moro@gmail.com>
Acked-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Clarify use of the I2C_M_* flags by highlighting the fact that
most of them depend on I2C_FUNC_PROTOCOL_MANGLING.
Also provide kerneldoc for i2c_smbus_read_block_data() and also
for "struct i2c_msg".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Do not initialize the PCF8574 with an arbitrary value. Users will have
to write the initial value to sysfs themselves.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Acked-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Use i2c_bit_add_numbered_adapter() if device id specified, so that the
i2c-ibm_iic adapter works well with new-style pre-declared devices.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Switch the tps65010 driver into a "new-style" I2C driver, and convert all
of its in-tree users (board support for OSK, H2, H3) accordingly.
That accounts for most of the board-specific code in this driver; the
rest of that code is now moved into board-specific initcalls.
Also remove some of the many now-superfluous #includes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Prepare to convert tps65010 driver to "new style" driver by changing
how it references the i2c_client. This lets the eventual patch with
driver and platform updates be smaller.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
We need to be able to flag I2C devices, such as RTCs, which can issue wake
events (usually through IRQ lines). This adds an i2c_board_info.flags bit,
and uses it to initialize the i2c device node. (And shrinks a few lines
that were overly long.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Commit 3d73c288 ("mlx4_core: Fix section mismatches") introduced a
stupid bug in device init: when some of mlx4_init_one() was split off
into __mlx4_init_one(), the call from the main mlx4_init_one()
function was back to mlx4_init_one() rather than to __mlx4_init_one(),
which leads to an obvious infinite loop if the function is every
called.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
RT guys alerted me to the fact that in their tree spinlocks
are preemptible and it is better to use full RCU API
(rcu_read_lock()/rcu_read_unlock()) to be safe.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
... and yes, caller wants it to return int.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: (106 commits)
KVM: Replace enum by #define
KVM: Skip pio instruction when it is emulated, not executed
KVM: x86 emulator: popf
KVM: x86 emulator: fix src, dst value initialization
KVM: x86 emulator: jmp abs
KVM: x86 emulator: lea
KVM: X86 emulator: jump conditional short
KVM: x86 emulator: imlpement jump conditional relative
KVM: x86 emulator: sort opcodes into ascending order
KVM: Improve emulation failure reporting
KVM: x86 emulator: pushf
KVM: x86 emulator: call near
KVM: x86 emulator: push imm8
KVM: VMX: Fix exit qualification width on i386
KVM: Move main vcpu loop into subarch independent code
KVM: VMX: Move vm entry failure handling to the exit handler
KVM: MMU: Don't do GFP_NOWAIT allocations
KVM: Rename kvm_arch_ops to kvm_x86_ops
KVM: Simplify memory allocation
KVM: Hoist SVM's get_cs_db_l_bits into core code.
...
Breaks on any target that has copy_to_user() defined as a non-trivial
macro.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (124 commits)
sh: allow building for both r2d boards in same binary.
sh: fix r2d board detection
sh: Discard .exit.text/.exit.data at runtime.
sh: Fix up some section alignments in linker script.
sh: Fix SH-4 DMAC CHCR masking.
sh: Rip out left-over nommu cond syscall cruft.
sh: Make kgdb i-cache flushing less inept.
sh: kgdb section mismatches and tidying.
sh: cleanup struct irqaction initializers.
sh: early_printk tidying.
video: pvr2fb: Add TV (RGB) support to Dreamcast PVR driver.
sh: Conditionalize gUSA support.
sh: Follow gUSA preempt changes in __switch_to().
sh: Tidy up gUSA preempt handling.
sh: __copy_user() optimizations for small copies.
sh: clkfwk: Support multi-level clock propagation.
sh: Fix URAM start address on SH7785.
sh: Use boot_cpu_data for CPU probe.
sh: Support extended mode TLB on SH-X3.
sh: Bump MAX_ACTIVE_REGIONS for SH7785.
...
We need to read the fan clock dividers at initialization time,
otherwise the code in store_fan_min() may use uninitialized values.
That's pretty much the same bug and same fix as for the w83627ehf
driver last month.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
ssb bus needs <linux/io.h>
linux/drivers/ssb/main.c: In function 'ssb_ssb_read16':
linux/drivers/ssb/main.c:518: error: implicit declaration of function 'readw'
linux/drivers/ssb/main.c: In function 'ssb_ssb_read32':
linux/drivers/ssb/main.c:526: error: implicit declaration of function 'readl'
linux/drivers/ssb/main.c: In function 'ssb_ssb_write16':
linux/drivers/ssb/main.c:534: error: implicit declaration of function 'writew'
linux/drivers/ssb/main.c: In function 'ssb_ssb_write32':
linux/drivers/ssb/main.c:542: error: implicit declaration of function 'writel'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
b43 wireless needs <linux/io.h>
linux/drivers/net/wireless/b43/pio.h: In function 'b43_pio_write':
linux/drivers/net/wireless/b43/pio.h:89: error: implicit declaration of function 'mmiowb'
linux/drivers/net/wireless/b43/phy.c: In function 'b43_phy_write':
linux/drivers/net/wireless/b43/phy.c:301: error: implicit declaration of function 'mmiowb'
linuxdrivers/net/wireless/b43/sysfs.c: In function 'b43_attr_interfmode_store':
linuxdrivers/net/wireless/b43/sysfs.c:147: error: implicit declaration of function 'mmiowb'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
emc_endio returns void:
linux/drivers/md/dm-emc.c: In function 'emc_endio':
linux/drivers/md/dm-emc.c:58: warning: 'return' with a value, in function returning void
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch to drivers/hwmon/w83627hf converts many sysfs items from DEVICE_ATTRs
to SENSOR_DEVICE_ATTRs, and replaces macros which expand to define redundant
callbacks, with callbacks which use the SENSOR_DEV.nr to know what to do.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
init_dma_ali15x3() guarantees that hwif->dma_base will never be set for
m5229_revision < 0x20 so remove redundant m5229_revision >= 0x20 check from
init_hwif_common_ali15x3().
While at it remove incorrect comment.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Set hwif->atapi_dma/{ultra,mwdma}_mask and drive->autodma after checking that
->dma_base exists. If ->dma_base is not set (== PCI BAR4 cannot be reserved)
then DMA hooks shouldn't be initialized or bad things will happen.
OTOH hwif->set_{pio,dma}_mode hooks should be set even if hwif->dma_base == 0.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Set hwif->ide_dma_{check,on} and hwif->autodma to 1 after checking that
->dma_base exists. If ->dma_base is not set (== PCI BAR4 cannot be reserved)
then DMA hooks shouldn't be initialized or bad things will happen.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Devices which don't set word 93 validation bit should be now handled by
ide-iops.c::ivb_list[] and for debugging purposes cable detection can be
completely overriden with "idex=ata66" parameter.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Need to probe slave device first to make it release PDIAG-
(this is required for correct device side cable detection).
Based on libata commit f31f0cc2f0.
Thanks to Craig for testing this patch.
Cc: Craig Block <chblock3@yahoo.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.
* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program
the host for the transfer mode after programming the device. Set it
in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
and via82cxxx host drivers.
* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
skip programming of host/device for the transfer mode ("smart" hosts).
Set it in it821x host driver and check it in ide_tune_dma().
* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
direct ->set_pio_mode/->speedproc users to use these helpers.
* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
methods to callers.
* Rename ->speedproc method to ->set_dma_mode, make it void and update
all implementations accordingly.
* Update ide_set_xfer_rate() comments.
* Unexport ide_config_drive_speed().
v2:
* Fix issues noticed by Sergei:
- export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
to setting DMA modes from sc1200_set_pio_mode() to do_special()
- check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
- check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
- check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
- return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
- don't set ->set_{pio,dma}_mode on it821x in "smart" mode
- fix build problem in pmac.c
- minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
- improve patch description
Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
the device (not really an issue since 0x00 is not supported correctly by
any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Check ide_config_drive_speed() return value.
* While at also call ide_config_drive_speed() if the transfer mode is
XFER_PIO_SLOW (this case happens iff the transfer mode has already been
set on the device by ide-proc.c::set_xfer_rate()) and remove redundant
setting of ->{init,current}_speed.
* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Set transfer mode on the device before programming the host controller for
the new timings (matches what auide_tune_chipset() is doing wrt DMA modes).
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add "good DMA drives" hack for icside to ide-dma.c::ide_find_dma_mode()
(in the long-term it should be either removed or generalized for all hosts).
* Use ide_tune_dma() in icside.c::icside_dma_check().
This results in the following changes in behavior:
- pre-EIDE SWDMA modes are now also respected
- drive->autodma is checked instead of hwif->autodma
(doesn't really matter as icside sets both to "1")
* Make ide-dma.c::__ide_dma_good_drive() static and drop "__" prefix.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add missing initialization of hwif->autodma and drive->autodma to
pmac_ide_setup_dma().
* Use ide_tune_dma() in pmac_ide_dma_check().
While at it:
* Fix pmac_ide_dma_check() return value if DMA mode is not programmed
(should be "-1" otherwise ide_set_dma() will try to enable DMA).
* Remove unnecessary drive->using_dma fiddling (->dma_off_quietly is always
called before ide_set_dma() call and ide_set_dma() calls ->ide_dma_on if
->ide_dma_check returns "0").
v2:
* No reason to blacklist all ide_floppy devices and the old code was always
enabling DMA anyway (without even programming controller/device if the
device was ide_floppy).
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ide_config_drive_speed() instead of pmac_ide_do_setfeature() and remove
the latter, also ide-iops.c::__ide_wait_stat() could be static again.
Since for IDE PMAC host driver IDE_CONTROL_REG is always true, device's
->quirk_list is always zero and ->ide_dma_host_{on,off} are nops than
the only changes in behavior are:
* if PIO mode is set then ->dma_off_queitly is called to disable DMA
* if setting transfer mode fails ide_dump_status() is called to dump status
v2:
* IDE PMAC controllers allow separate PIO and DMA timings and PPC userland
depends on this fact, and calls "hdparm -p" without calling "hdparm -d".
Therefore to compensate for DMA being disabled by ide_config_drive_speed()
for PIO modes:
- add IDE_HFLAG_SET_PIO_MODE_KEEP_DMA flag and set it in PMAC host driver
- add handling of the new flag to ide-io.c::do_special()
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Upper layers are responsible for controlling nIEN so don't clear nIEN after
command execution in pmac_ide_do_setfeature().
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use __ide_wait_stat() instead of wait_for_ready() in pmac_ide_do_setfeature().
While at it do following changes to match __ide_wait_stat() call in
ide_config_drive_speed():
* Wait WAIT_CMD time (20 sec) instead of 2 sec for device to clear BUSY_STAT.
* Check DRQ_STAT bit (shouldn't be set for good device status).
Also remove no longer needed wait_for_ready() from ide-iops.c.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't check for good device status before executing the command in
pmac_ide_do_setfeature() (ide_config_drive_speed() doesn't do this).
It is a job of upper layers to guarantee that the device is ready to
accept new command before we get here.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Split off checking of the status register from ide_wait_stat() to
__ide_wait_stat() helper.
* Use the new helper in ide_config_drive_speed(). The only change in the
functionality is that the function now fails if after 20 sec (WAIT_CMD)
device is still busy (BUSY_STAT bit is set) while previously instead of
failing the function continued with checking for the correct device status
(which would give the device additional 10 usec to clear BUSY_STAT bit).
* Remove stale comment for ide_config_drive_speed().
* Remove duplicate comment for ide_wait_stat() from <linux/ide.h>.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Fix pmac_ide_dma_check() to use pmac_ide_tune_chipset() and remove no longer
necessary pmac_ide_{m,u}dma_enable().
* While at it remove some dead code from pmac_ide_dma_check() (leftovers from
conversion to use ide_max_dma_mode()).
There should be no functionality changes caused by this patch.
v2:
* Fix compile by replacing "id" with "drive->id" in pmac_ide_dma_check()
(Noticed by Ben).
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
pmac_ide_do_setfeature() contains matching nIEN setting/clearing so this
Device Control register messing in pmac_ide_dma_check() is totally unnecessary.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Move adjusting of cycle time for devices providing explicit DMA cycle time
from pmac_ide_mdma_enable() to set_timings_mdma().
* Remove no longer needed drive_cycle_time argument.
* BUG() if unsupported speed argument value is passed (shouldn't happen).
* Matching access/recovery timings always exist so remove redundant check.
* Make set_timings_mdma() void.
* Update pmac_ide_tune_chipset()'s comment.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Don't check check for pmif == NULL (it should never be NULL if we got here).
* Make a local copy of the timings and set the pmif->timings[] only after
setting the transfer mode on the device (otherwise SELECT_DRIVE() call in
pmac_ide_do_setfeature() will program new timings before the transfer mode
is set on the device - this was pointed out by Sergei). This change makes
pmac_ide_tune_chipset() behavior match this of pmac_ide_{m,u}dma_enable().
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
kauai_lookup_timing() should always return non-zero return value:
* BUG() in kauai_lookup_timing() if the timing info cannot be found.
* Remove code checking for zero return value from all callers.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This patch removes the unused EXPORT_SYMBOL_GPL(ide_acpi_set_state)
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We need to set hwif->chipset or IDE PCI host drivers may try to claim
our ide_hwifs[] slot.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is the driver for latest Blackfin on-chip nand flash controller
- use nand_chip and mtd_info common nand driver interface
- provide both PIO and dma operation
- compiled with ezkit bf548 configuration
- use hardware 1-bit ECC
- tested with YAFFS2 and can mount YAFFS2 filesystem as rootfs
ChangeLog from try#1
- use hweight32() instead of count_bits()
- replace bf54x with bf5xx and BF54X with BF5XX
- compare against plat->page_size in 2 cases when enable hardware ECC
ChangeLog from try#2
- passed nand_test suites
- use cpu_relax() instead of busy wait loop
- some coding style issue pointed out by Andrew
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When we press ctrl-alt-del,kernel_restart_prepare will invoke
cfi_intelext_reboot which will set flash to read array mode, but later
when device_shutdown is invoked which may put current work queue to
sleep and other process may be scheduled to running and programming
flash in not FL_READY mode again. So we can't boot up if this flash is
used for bootloader.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/nand/alauda.c: In function 'alauda_bounce_read':
drivers/mtd/nand/alauda.c:412: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
If we defer updating rip until pio instructions are executed, we have a
problem with reset: a pio reset updates rip, and when the instruction
completes we skip the emulated instruction, pointing rip somewhere completely
unrelated.
Fix by updating rip when we see decode the instruction, not after emulation.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Some operand fetches are less than the machine word size and can result in
stale bits if used together with operands of different sizes.
Signed-off-by: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Implement emulation of instruction
lea r16/r32, m
opcode: 0x8d:
Signed-off-by: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
According to Intel Software Developer's Manual, Vol. 3B, Appendix H.4.2,
exit qualification should be of natural width. However, current code
uses u64 as the data type for this register, which occasionally
introduces invalid value to VMExit handling logics. This patch fixes
this bug.
I have tested Windows and Linux guest on i386 host, and they can boot
successfully with this patch.
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Before preempt notifiers, kvm needed to allocate memory with GFP_NOWAIT so
as not to have to enable preemption and take a heavyweight exit. On oom, we'd
fall back to a GFP_KERNEL allocation.
With preemption notifiers, we can do a GFP_KERNEL allocation, and perform
the heavyweight exit only if the kernel decides to put us to sleep.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch just renames the current (misnamed) _arch namings to _x86 to
ensure better readability when a real arch layer takes place.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The mutex->splinlock convertion alllows us to make some code simplifications.
As we can keep the lock longer, we don't have to release it and then
have to check if the environment has not been modified before re-taking it. We
can remove kvm->busy and kvm->memory_config_version.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
SVM gets the DB and L bits for the cs by decoding the segment. This
is in fact the completely generic code, so hoist it for kvm-lite to use.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
We don't update the vcpu control registers in various places. We
should do so.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
invlpg shouldn't fetch the "src" address, since it may not be valid,
however SVM's "solution" which neuters emulation of all group 7
instruction is horrible and breaks kvm-lite. The simplest fix is to
put a special check in for invlpg.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This was missed when moving stuff around in fbc4f2e
Fixes Solaris guests and bug #1773613
Signed-off-by: Amit Shah <amit.shah@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch enables INIT/SIPI handling using in-kernel APIC by
introducing a ->mp_state field to emulate the SMP state transition.
[avi: remove smp_processor_id() warning]
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Xin Li <xin.b.li@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch changes the PIC interrupts delivery. Now it is only delivered
to vcpu0 when either condition is met (on vcpu0):
1. local APIC is hardware disabled
2. LVT0 is unmasked and configured to delivery mode ExtInt
It fixes the 2x faster wall clock on x86_64 and SMP i386 Linux guests
Signed-off-by: Eddie (Yaozu) Dong <eddie.dong@intel.com>
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This reduces overhead by accessing cachelines from the wrong node, as well
as simplifying locking.
[Qing: fix for inactive or expired one-shot timer]
Signed-off-by: Yaozu (Eddie) Dong <Eddie.Dong@intel.com>
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
APIC timer IRQ is set every time when a certain period
expires at host time, but the guest may be descheduled
at that time and thus the irq be overwritten by later fire.
This patch keep track of firing irq numbers and decrease
only when the IRQ is injected to guest or buffered in
APIC.
Signed-off-by: Yaozu (Eddie) Dong <Eddie.Dong@intel.com>
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch enables TPR shadow of VMX on CR8 access. 64bit Windows using
CR8 access TPR frequently. The TPR shadow can improve the performance of
access TPR by not causing vmexit.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds a new vcpu-based IOCTL to save and restore the local
apic registers for a single vcpu. The kernel only copies the apic page as
a whole, extraction of registers is left to userspace side. On restore, the
APIC timer is restarted from the initial count, this introduces a little
delay, but works fine.
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds support for in-kernel ioapic save and restore (to
and from userspace). It uses the same get/set_irqchip ioctl as
in-kernel PIC.
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
vcpu->irq_pending is saved in get/set_sreg IOCTL, but when in-kernel
local APIC is used, doing this may occasionally overwrite vcpu->apic to
an invalid value, as in the vm restore path.
Signed-off-by: Qing He <qing.he@intel.com>
This patch adds two new ioctls to dump and write kernel irqchips for
save/restore and live migration. PIC s/r and l/m is implemented in this
patch.
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
pio operation and IRQ_LINE kvm_vm_ioctl is not kvm->lock
protected. Add lock to same with IOAPIC MMIO operations.
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
By sleeping in the kernel when hlt is executed, we simplify the in-kernel
guest interrupt path considerably.
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Because lightweight exits (exits which don't involve userspace) are many
times faster than heavyweight exits, it makes sense to emulate high usage
devices in the kernel. The local APIC is one such device, especially for
Windows and for SMP, so we add an APIC model to kvm.
It also allows in-kernel host-side drivers to inject interrupts without
going through userspace.
[compile fix on i386 from Jindrich Makovicka]
Signed-off-by: Yaozu (Eddie) Dong <Eddie.Dong@intel.com>
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch is to wrap APIC base register and CR8 operation which can
provide a unique API for user level irqchip and kernel irqchip.
This is a preparation of merging lapic/ioapic patch.
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
vmx_load_host_state() bundles fs, gs, ldt, and tss reloading into
one in the hope that it is infrequent. With smp guests, fs reloading is
frequent due to fs being used by threads.
Unbundle the reloads so reduce expensive gs reloads.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Implement emulation of instruction
and al imm8 (opcode 0x24)
and ax/eax imm16/imm32 (opcode 0x25)
Signed-off-by: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
We need to check for signals inside the critical section, otherwise a
signal can be sent which we will not notice. Also move the check
before entry, so that if the signal happens before the first entry,
we exit immediately instead of waiting for something to happen to the
guest.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Split kvm_setup_pio() into two functions, one to setup in/out pio
(kvm_emulate_pio()) and one to setup ins/outs pio (kvm_emulate_pio_string()).
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Both vmx and svm decode the I/O instructions, and both botch the job,
requiring the instruction prefixes to be fetched in order to completely
decode the instruction.
So, if we see a string I/O instruction, use the x86 emulator to decode it,
as it already has all the prefix decoding machinery.
This patch defines ins/outs opcodes in x86_emulate.c and calls
emulate_instruction() from io_interception() (svm.c) and from handle_io()
(vmx.c). It removes all vmx/svm prefix instruction decoders
(get_addr_size(), io_get_override(), io_address(), get_io_count())
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Line 1809 of kvm_main.c is useless, value is overwritten in line 1815:
1809 now = min(count, PAGE_SIZE / size);
1810
1811 if (!down)
1812 in_page = PAGE_SIZE - offset_in_page(address);
1813 else
1814 in_page = offset_in_page(address) + size;
1815 now = min(count, (unsigned long)in_page / size);
1816 if (!now) {
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Remove a duplicated ia32e mode VM Entry control definition and use the
proper one.
Signed-off-by: Xin Li <xin.b.li@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
We use kfree in svm.c and vmx.c, and this works, but it could break at
any time. kfree() is supposed to match up with kmalloc().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
All guest-invokable printks should be ratelimited to prevent malicious
guests from flooding logs. This is a start.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
We shouldn't define stat_set on the debug attributes, since that will
cause silent failure on writing: without a set argument, userspace
will get -EACCESS.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
move_msr_up() is used only on X86_64 and generates a warning on !X86_64
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
alloc_vmcs_cpu is already declared (static) above, no need to
redeclare.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
set_msr_interception() is used by svm to set up which MSRs should be
intercepted. It can only fail if someone has changed the code to try
to intercept an MSR without updating the array of ranges.
The return value is ignored anyway: it should just BUG() if it doesn't
work. (A build-time failure would be better, but that's tricky).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
For some reason, mark_page_dirty open-codes __gfn_to_memslot().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
All the physical CPUs on the board should support the same VMX feature
set. Add check_processor_compatibility to kvm_arch_ops for the consistency
check.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
kvm_vm_ioctl_get_dirty_log scans bitmap to see it it's all zero, but
doesn't use that information.
Avi says:
Looks like it was used to guard kvm_mmu_slot_remove_write_access();
optimizing the case where the guest just leaves the screen alone (which
it usually does, especially in benchmarks).
I'd rather reinstate that optimization. See
90cb0529dd where the damage was done.
It's pretty simple: if the bitmap is all zero, we don't need to do anything to
clean it.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Now we use a kmem cache for allocating vcpus, we can get the 16-byte
alignment required by fxsave & fxrstor instructions, and avoid
manually aligning the buffer.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Avi wants the allocations of vcpus centralized again. The easiest way
is to add a "size" arg to kvm_init_arch, and expose the thus-prepared
cache to the modules.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
... in favor of the more general emulator_{read,write}_*.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
... instead of a x86_emulate_ctxt, so that other callers can use it easily.
Signed-off-by: Laurent Vivier <Laurent.Vivier@bull.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Changes some svm.c internal function names:
1) io_adress -> io_address (de-germanify the spelling)
2) kvm_reput_irq -> reput_irq (it's not a generic kvm function)
3) kvm_do_inject_irq -> (it's not a generic kvm function)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
container_of is wonderful, but not casting at all is better. This
patch changes svm.c's internal functions to pass "struct vcpu_svm"
instead of "struct kvm_vcpu" and using container_of.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
There are several places where hardcoded numbers are used in place of
the easily-available constant, which is poor form.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
container_of is wonderful, but not casting at all is better. This
patch changes vmx.c's internal functions to pass "struct vcpu_vmx"
instead of "struct kvm_vcpu" and using container_of.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Now that kvm generally runs with preemption enabled, we need to protect
the fpu intialization sequence.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This allows the kvm mmu to perform sleepy operations, such as memory
allocation.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Current kvm disables preemption while the new virtualization registers are
in use. This of course is not very good for latency sensitive workloads (one
use of virtualization is to offload user interface and other latency
insensitive stuff to a container, so that it is easier to analyze the
remaining workload). This patch re-enables preemption for kvm; preemption
is now only disabled when switching the registers in and out, and during
the switch to guest mode and back.
Contains fixes from Shaohua Li <shaohua.li@intel.com>.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Add the hypercall number to kvm_run and initialize it. This changes the ABI,
but as this particular ABI was unusable before this no users are affected.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Put cpu feature detecting part in hardware_setup, and stored the vmcs
condition in global variable for further check.
[glommer: fix for some i386-only machines not supporting CR8 load/store
exiting]
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch converts the vcpus array in "struct kvm" to a pointer
array, and changes the "vcpu_create" and "vcpu_setup" hooks into one
"vcpu_create" call which does the allocation and initialization of the
vcpu (calling back into the kvm_vcpu_init core helper).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
struct kvm_vcpu has vmx-specific members; remove them to a private structure.
Signed-off-by: Gregory Haskins <ghaskins@novell.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
load_pdptrs can be handed an invalid cr3, and it should not oops.
This can happen because we injected #gp in set_cr3() after we set
vcpu->cr3 to the invalid value, or from kvm_vcpu_ioctl_set_sregs(), or
memory configuration changes after the guest did set_cr3().
We should also copy the pdpte array once, before checking and
assigning, otherwise an SMP guest can potentially alter the values
between the check and the set.
Finally one nitpick: ret = 1 should be done as late as possible: this
allows GCC to check for unset "ret" should the function change in
future.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The writeback fixes (02c03a326a) let
some dead code in the cmpxchg instruction emulation. Remove it.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch mainly imports some constants and rename two exist constants
of vmcs according to IA32 SDM.
It also adds two constants to indicate Lock bit and Enable bit in
MSR_IA32_FEATURE_CONTROL, and replace the hardcode _5_ with these two
bits.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
gfn_to_page might sleep with swap support. Move it out of the kmap calls.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
vmx_cpu_run doesn't handle error correctly and kvm_mmu_reload might
sleep with mutex changes, so I move it above.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Right now, the bug is harmless as we never emulate one-byte 0xb6 or 0xb7.
But things may change.
Noted by the mysterious Gabriel C.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Intel manual (and KVM definition) say the TPR is 4 bits wide. Also fix
CR8_RESEVED_BITS typo.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Creating one's own BITMAP macro seems suboptimal: if we use manual
arithmetic in the one place exposed to userspace, we can use standard
macros elsewhere.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
On this machine (Intel), writing to the CR4 bits 0x00000800 and
0x00001000 cause a GPF. The Intel manual is a little unclear, but
AFIACT they're reserved, too.
Also fix spelling of CR4_RESEVED_BITS.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The kernel now has asm/cpu-features.h: use those macros instead of inventing
our own.
Also spell out definition of CR3_RESEVED_BITS, fix spelling and
tighten it for the non-PAE case.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The kernel now has asm/cpu-features.h: use those macros instead of
inventing our own.
Also spell out definition of CR0_RESEVED_BITS (no code change) and fix typo.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
I have shied away from touching x86_emulate.c (it could definitely use
some love, but it is forked from the Xen code, and it would be more
productive to cross-merge fixes).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Add string pio write support to support some version of Windows.
Signed-off-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds a `vcpu_id' field in `struct vcpu', so we can
differentiate BSP and APs without pointer comparison or arithmetic.
Signed-off-by: Qing He <qing.he@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
*nopage() in kvm_main.c should only store the type of mmap() fault if
the pointers are not NULL. This patch fixes the problem.
Signed-off-by: Nguyen Anh Quynh <aquynh@gmail.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Make sure we reset idlecount when we get a good (non-empty) packet.
Signed-off-by: Soeren Sonnenburg <kernel@nn7.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Switch to using input-polldev skeleton instead of implementing polling loop
by itself. This also fixes problem with trylock on a mutex in atomic
context.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (119 commits)
[libata] struct pci_dev related cleanups
libata: use ata_exec_internal() for PMP register access
libata: implement ATA_PFLAG_RESETTING
libata: add @timeout to ata_exec_internal[_sg]()
ahci: fix notification handling
ahci: clean up PORT_IRQ_BAD_PMP enabling
ahci: kill leftover from enabling NCQ over PMP
libata: wrap schedule_timeout_uninterruptible() in loop
libata: skip suppress reporting if ATA_EHI_QUIET
libata: clear ehi description after initial host report
pata_jmicron: match vendor and class code only
libata: add ST9160821AS / 3.ALD to NCQ blacklist
pata_acpi: ACPI driver support
libata-core: Expose gtm methods for driver use
libata: add HDT722516DLA380 to NCQ blacklist
libata: blacklist NCQ on Seagate Barracuda ST380817AS
[libata] Turn on ACPI by default
libata_scsi: Fix ATAPI transfer lengths
libata: correct handling of SRST reset sequences
libata: Integrate ACPI-based PATA/SATA hotplug - version 5
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (37 commits)
PCI: merge almost all of pci_32.h and pci_64.h together
PCI: X86: Introduce and enable PCI domain support
PCI: Add 'nodomains' boot option, and pci_domains_supported global
PCI: modify PCI bridge control ISA flag for clarity
PCI: use _CRS for PCI resource allocation
PCI: avoid P2P prefetch window for expansion ROMs
PCI: skip ISA ioresource alignment on some systems
PCI: remove transparent bridge sizing
pci: write file size to inode on proc bus file write
pci: use size stored in proc_dir_entry for proc bus files
pci: implement "pci=noaer"
PCI: fix IDE legacy mode resources
MSI: Use correct data offset for 32-bit MSI in read_msi_msg()
PCI: Fix incorrect argument order to list_add_tail() in PCI dynamic ID code
PCI: i386: Compaq EVO N800c needs PCI bus renumbering
PCI: Remove no longer correct documentation regarding MSI vector assignment
PCI: re-enable onboard sound on "MSI K8T Neo2-FIR"
PCI: quirk_vt82c586_acpi: Omit reading PCI revision ID
PCI: quirk amd_8131_mmrbc: Omit reading pci revision ID
cpqphp: Use PCI_CLASS_REVISION instead of PCI_REVISION_ID for read
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (75 commits)
PM: merge device power-management source files
sysfs: add copyrights
kobject: update the copyrights
kset: add some kerneldoc to help describe what these strange things are
Driver core: rename ktype_edd and ktype_efivar
Driver core: rename ktype_driver
Driver core: rename ktype_device
Driver core: rename ktype_class
driver core: remove subsystem_init()
sysfs: move sysfs file poll implementation to sysfs_open_dirent
sysfs: implement sysfs_open_dirent
sysfs: move sysfs_dirent->s_children into sysfs_dirent->s_dir
sysfs: make sysfs_root a regular directory dirent
sysfs: open code sysfs_attach_dentry()
sysfs: make s_elem an anonymous union
sysfs: make bin attr open get active reference of parent too
sysfs: kill unnecessary NULL pointer check in sysfs_release()
sysfs: kill unnecessary sysfs_get() in open paths
sysfs: reposition sysfs_dirent->s_mode.
sysfs: kill sysfs_update_file()
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (142 commits)
USB: fix race in autosuspend reschedule
atmel_usba_udc: Keep track of the device status
USB: Nikon D40X unusual_devs entry
USB: serial core should respect driver requirements
USB: documentation for USB power management
USB: skip autosuspended devices during system resume
USB: mutual exclusion for EHCI init and port resets
USB: allow usbstorage to have LUNS greater than 2Tb
USB: Adding support for SHARP WS011SH to ipaq.c
USB: add atmel_usba_udc driver
USB: ohci SSB bus glue
USB: ehci build fixes on au1xxx, ppc-soc
USB: add runtime frame_no quirk for big-endian OHCI
USB: funsoft: Fix termios
USB: visor: termios bits
USB: unusual_devs entry for Nikon DSC D2Xs
USB: re-remove <linux/usb_sl811.h>
USB: move <linux/usb_gadget.h> to <linux/usb/gadget.h>
USB: Export URB statistics for powertop
USB: serial gadget: Disable endpoints on unload
...
