- Fix endpoint driver sign extension problem when shifting page number to
phys_addr_t (Alan Mikhak)
* remotes/lorenzo/pci/endpoint:
PCI: endpoint: Cast the page number to phys_addr_t
- Refactor Cadence PCIe host controller to use as a library for both host
and endpoint (Tom Joseph)
* remotes/lorenzo/pci/cadence:
PCI: cadence: Move all files to per-device cadence directory
PCI: cadence: Refactor driver to use as a core library
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted before
the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi Pommarel)
- Don't rely on jiffies in Aardvark config access path since interrupts
may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
* remotes/lorenzo/pci/aardvark:
PCI: pci-bridge-emul: Fix big-endian support
PCI: aardvark: Fix big endian support
PCI: aardvark: Don't rely on jiffies while holding spinlock
PCI: aardvark: Fix PCI_EXP_RTCTL register configuration
PCI: aardvark: Wait for endpoint to be ready before training link
PCI: aardvark: Use LTSSM state to build link training flag
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the VFs,
but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and associated
VFs can be enabled independently (Kuppuswamy Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn Helgaas)
- Hide PRI and PASID state restoration functions used only inside the PCI
core (Bjorn Helgaas)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George Cherian)
- Unify ACS quirk implementations (Bjorn Helgaas)
* pci/virtualization:
PCI: Unify ACS quirk desired vs provided checking
PCI: Make ACS quirk implementations more uniform
PCI: Apply Cavium ACS quirk to ThunderX2 and ThunderX3
PCI/IOV: Serialize sysfs sriov_numvfs reads vs writes
PCI: Add DMA alias quirk for Intel VCA NTB
PCI: Fix Intel ACS quirk UPDCR register address
PCI/ATS: Make pci_restore_pri_state(), pci_restore_pasid_state() private
PCI/ATS: Remove unnecessary EXPORT_SYMBOL_GPL()
PCI/ATS: Remove unused PRI and PASID stubs
PCI/ATS: Consolidate ATS declarations in linux/pci-ats.h
PCI/ATS: Cache PRI PRG Response PASID Required bit
PCI/ATS: Cache PASID Capability offset
PCI/ATS: Cache PRI Capability offset
PCI/ATS: Disable PF/VF ATS service independently
PCI/ATS: Handle sharing of PF PASID Capability with all VFs
PCI/ATS: Handle sharing of PF PRI Capability with all VFs
PCI/ATS: Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI
iommu/vt-d: Select PCI_PRI for INTEL_IOMMU_SVM
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the
MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA devices
downstream (Subbaraya Sundeep)
* pci/resource:
PCI: Do not use bus number zero from EA capability
PCI: Avoid double hpmemsize MMIO window assignment
PCI: Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters
PCI: Add PCI_STD_NUM_BARS for the number of standard BARs
PCI: Fix missing bridge dma_ranges resource list cleanup
PCI: Protect pci_reassign_bridge_resources() against concurrent addition/removal
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we only
did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0) instead
of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
* pci/pm:
PCI/PM: Move pci_dev_wait() definition earlier
PCI/PM: Add missing link delays required by the PCIe spec
PCI/PM: Add pcie_wait_for_link_delay()
PCI/PM: Return error when changing power state from D3cold
PCI/PM: Decode D3cold power state correctly
PCI/PM: Fold __pci_complete_power_transition() into its caller
PCI/PM: Avoid exporting __pci_complete_power_transition()
PCI/PM: Fold __pci_start_power_transition() into its caller
PCI/PM: Use pci_power_up() in pci_set_power_state()
PCI/PM: Move power state update away from pci_power_up()
PCI/PM: Remove unused pci_driver.suspend_late() hook
PCI/PM: Remove unused pci_driver.resume_early() hook
xen-platform: Convert to generic power management
PCI/PM: Simplify pci_set_power_state()
PCI/PM: Expand PM reset messages to mention D3hot (not just D3)
PCI/PM: Apply D2 delay as milliseconds, not microseconds
PCI/PM: Use pci_WARN() to include device information
PCI/PM: Use PCI dev_printk() wrappers for consistency
PCI/PM: Wrap long lines in documentation
PCI/PM: Note that PME can be generated from D0
PCI/PM: Make power management op coding style consistent
PCI/PM: Run resume fixups before disabling wakeup events
PCI/PM: Clear PCIe PME Status even for legacy power management
PCI/PM: Correct pci_pm_thaw_noirq() documentation
PCI/PM: Always return devices to D0 when thawing
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk for
Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
* pci/msi:
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC even
if platform didn't grant control over AER (Olof Johansson)
* pci/aer:
PCI/DPC: Add "pcie_ports=dpc-native" to allow DPC without AER control
PCI/AER: Fix kernel-doc warnings
PCI/AER: Use for_each_set_bit() to simplify code
PCI/AER: Add PoisonTLPBlocked to Uncorrectable error counters
PCI/AER: Save AER Capability for suspend/resume
The only apparent reason for the PCI_MSI_IRQ_DOMAIN architecture
whitelist was that it requires msi.h. Now that msi.h is mandatory in
asm-generic/Kbuild, every arch should have at least the default version,
so remove the whitelist.
Built for all the architectures that play nice with make.cross, but not
boot tested anywhere.
Link: https://lore.kernel.org/r/514e7b040be8ccd69088193aba260da1b89e919c.1571983829.git.michal.simek@xilinx.com
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Waiman Long <longman@redhat.com>
When a driver enables MSI-X, msix_program_entries() reads the MSI-X Vector
Control register for each vector and saves it in desc->masked. Each
register is 32 bits and bit 0 is the actual Mask bit.
When we restored these registers during resume, we previously set the Mask
bit if *any* bit in desc->masked was set instead of when the Mask bit
itself was set:
pci_restore_state
pci_restore_msi_state
__pci_restore_msix_state
for_each_pci_msi_entry
msix_mask_irq(entry, entry->masked) <-- entire u32 word
__pci_msix_desc_mask_irq(desc, flag)
mask_bits = desc->masked & ~PCI_MSIX_ENTRY_CTRL_MASKBIT
if (flag) <-- testing entire u32, not just bit 0
mask_bits |= PCI_MSIX_ENTRY_CTRL_MASKBIT
writel(mask_bits, desc_addr + PCI_MSIX_ENTRY_VECTOR_CTRL)
This means that after resume, MSI-X vectors were masked when they shouldn't
be, which leads to timeouts like this:
nvme nvme0: I/O 978 QID 3 timeout, completion polled
On resume, set the Mask bit only when the saved Mask bit from suspend was
set.
This should remove the need for 19ea025e1d ("nvme: Add quirk for Kingston
NVME SSD running FW E8FK11.T").
[bhelgaas: commit log, move fix to __pci_msix_desc_mask_irq()]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=204887
Link: https://lore.kernel.org/r/20191008034238.2503-1-jian-hong@endlessm.com
Fixes: f2440d9acb ("PCI MSI: Refactor interrupt masking code")
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
27e20603c5 ("PCI/MSI: Move D0 check into pci_msi_check_device()")
moved the power state check into pci_msi_check_device(), which was
subsequently renamed to pci_msi_supported(). This didn't change the
behavior, since both callers checked the power state.
However, it doesn't fit the current "pci_msi_supported()" name, which
should return what the device is capable of, independent of the power
state.
Move the power state check back into the callers for readability. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The function pci_irq_get_node() is not used by anyone in the tree, so just
delete it.
Link: https://lore.kernel.org/r/20191014100452.GA6699@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
With the recent 59bb47985c ("mm, sl[aou]b: guarantee natural
alignment for kmalloc(power-of-two)"), kzalloc() is able to allocate
a 4KB buffer that is guaranteed to be 4KB-aligned. Here the size and
alignment of hbus is important because hbus's field
retarget_msi_interrupt_params must not cross a 4KB page boundary.
Here we prefer kzalloc to get_zeroed_page(), because a buffer
allocated by the latter is not tracked and scanned by kmemleak, and
hence kmemleak reports the pointer contained in the hbus buffer
(i.e. the hpdev struct, which is created in new_pcichild_device() and
is tracked by hbus->children) as memory leak (false positive).
If the kernel doesn't have 59bb47985c, get_zeroed_page() *must* be
used to allocate the hbus buffer and we can avoid the kmemleak false
positive by using kmemleak_alloc() and kmemleak_free() to ask
kmemleak to track and scan the hbus buffer.
Reported-by: Lili Deng <v-lide@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
A VM can have multiple Hyper-V hbus. It's incorrect to set the global
variable 'pci_protocol_version' when *every* hbus is initialized in
hv_pci_protocol_negotiation(). This is not an issue in practice since
every hbus should have the same value of hbus->protocol_version, but
we should make the variable per-hbus, so in case we have busses
with different protocol versions, the driver can still work correctly.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Add suspend() and resume() functions so that Hyper-V virtual PCI devices
are handled properly when the VM hibernates and resumes from
hibernation.
Note that the suspend() function must make sure there are no pending
work items before calling vmbus_close(), since it runs in a process
context as a callback in dpm_suspend(). When it starts to run, the
channel callback hv_pci_onchannelcallback(), which runs in a tasklet
context, can be still running concurrently and scheduling new work items
onto hbus->wq in hv_pci_devices_present() and hv_pci_eject_device(), and
the work item handlers can access the vmbus channel, which can be being
closed by hv_pci_suspend(), e.g. the work item handler
pci_devices_present_work() -> new_pcichild_device() writes to the vmbus
channel.
To eliminate the race, hv_pci_suspend() disables the channel callback
tasklet, sets hbus->state to hv_pcibus_removing, and re-enables the
tasklet. This way, when hv_pci_suspend() proceeds, it knows that no new
work item can be scheduled, and then it flushes hbus->wq and safely
closes the vmbus channel.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
There is no functional change. This is just preparatory for a later
patch which adds the hibernation support for the pci-hyperv driver.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Some more development work for v5.5. Highlights include:
- More cleanups from Morimoto-san.
- Trigger word detection for RT5677.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl3bzrQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0LkMB/4/MkpN4F2WudNCKgmYay2gw3hq8aOR
5Xh/SE6N3BEgBpQiMEUdePRT6LqnQMsSpOaUoKfd4nFvCyLaV7itaYzQuUpo+UJ/
a4UDHJPVfrDJeFghWqSngfEW/N66mpO3UuAvhSRTR3ku0T31v9FkcLsMbdxVUpLC
ablSaFfPCOtTQOsG9blRUL/GAWUhGzPI/Hl4VldS0FvKDmMDY2fxt7QxXRaEYItc
i1Uthklxd0BfRmDqv0WEpduUhbwzg6Uir9pXSisux7DpMk1Li0IyPST5UcRl0Zf4
CKL/qfdQANpufj9kGmrlCOnXB9P5/XYVwfYV430WqMyw0QaOzzSrxT7C
=CZ/+
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: More updates for v5.5
Some more development work for v5.5. Highlights include:
- More cleanups from Morimoto-san.
- Trigger word detection for RT5677.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Previously, CONFIG_PCIEASPM_DEBUG enabled "link_state" and "clk_ctl" sysfs
files that controlled ASPM. We believe these files were rarely if ever
used.
We recently added sysfs ASPM controls that are always present, so the debug
code is no longer needed. Removing this debug code has been discussed for
quite some time, see e.g. [0].
Remove PCIEASPM_DEBUG and the related code.
[0] https://lore.kernel.org/lkml/20180727202619.GD173328@bhelgaas-glaptop.roam.corp.google.com/
Link: https://lore.kernel.org/r/ec935d8e-c084-3938-f1d1-748617596b25@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add sysfs attributes to Endpoints and other Upstream Ports to control ASPM,
Clock PM, and L1 PM Substates. The new attributes are:
/sys/devices/pci*/.../link/clkpm
/sys/devices/pci*/.../link/l0s_aspm
/sys/devices/pci*/.../link/l1_aspm
/sys/devices/pci*/.../link/l1_1_aspm
/sys/devices/pci*/.../link/l1_2_aspm
/sys/devices/pci*/.../link/l1_1_pcipm
/sys/devices/pci*/.../link/l1_2_pcipm
An attribute is only visible if both ends of the Link leading to the device
support the state. Writing y/1/on to the file enables the state; n/0/off
disables it.
These attributes can be used to tune the power/performance tradeoff for
individual devices.
[bhelgaas: commit log, rename directory to "link"]
Link: https://lore.kernel.org/r/b1c83f8a-9bf6-eac5-82d0-cf5b90128fbf@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
[bhelgaas: do same in vmd.c]
Link: https://lore.kernel.org/r/20191120134036.14502-1-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Set the mode register to host(RC) mode so that the host controller
mode is set-up consistently across SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
[lorenzo.pieralisi@arm.com: updated log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Some things in drivers/pci/pcie (aspm.c and ptm.c) do not depend on the
PCIe portdrv, so we should be able to build them even if PCIEPORTBUS is not
selected. Remove the PCIEPORTBUS guard from building pcie/.
Link: https://lore.kernel.org/r/20191106222420.10216-6-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
drivers/pci/pcie/Kconfig is only sourced by drivers/pci/Kconfig, and only
when PCI is defined, so there's no need to depend on PCI again. Remove the
unnecessary dependencies.
Link: https://lore.kernel.org/r/20191106222420.10216-5-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
The PTM support does not depend on the portdrv, so remove the Kconfig
dependency.
Link: https://lore.kernel.org/r/20191106222420.10216-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Jonathan Yong <jonathan.yong@intel.com>
The granularity message has an extra "d":
pci 0000:02:00.0: PTM enabled, 4dns granularity
Remove the "d" so the message is simply "PTM enabled, 4ns granularity".
Fixes: 8b2ec318ee ("PCI: Add PTM clock granularity information")
Link: https://lore.kernel.org/r/20191106222420.10216-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Jonathan Yong <jonathan.yong@intel.com>
56c1af4606 ("PCI: Add sysfs max_link_speed/width,
current_link_speed/width, etc") added the following objects, but they are
unused, so remove them:
pci_bridge_group
pci_bridge_groups
pcie_dev_group
pcie_dev_groups
This fixes the following warnings from sparse:
drivers/pci/pci-sysfs.c:1546:30: warning: symbol 'pci_bridge_groups' was not declared. Should it be static?
drivers/pci/pci-sysfs.c:1555:30: warning: symbol 'pcie_dev_groups' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20191016080324.12864-1-ben.dooks@codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove <linux/pci.h> and <linux/msi.h> from being included directly as part
of the include/linux/of_pci.h, and remove superfluous declaration of struct
of_phandle_args.
Move users of include <linux/of_pci.h> to include <linux/pci.h> and
<linux/msi.h> directly rather than rely on both being included transitively
through <linux/of_pci.h>.
Link: https://lore.kernel.org/r/20190903113059.2901-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Change:
drivers/pci/controller/pcie-cadence.h
drivers/pci/controller/pcie-rockchip.h
to use the correct SPDX comment style per section 2 of
Documentation/process/license-rules.rst.
These resolve the following checkpatch.pl warning:
WARNING: Missing or malformed SPDX-License-Identifier tag in line 1
[bhelgaas: split to separate patch]
Link: https://lore.kernel.org/r/20190828135322.10370-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move the definition of pci_dev_wait() above pci_power_up() so that it can
be called from the latter with no change in functionality. This is a pure
code move with no functional change.
Link: https://lore.kernel.org/r/20191120051743.23124-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently Linux does not follow PCIe spec regarding the required delays
after reset. A concrete example is a Thunderbolt add-in-card that consists
of a PCIe switch and two PCIe endpoints:
+-1b.0-[01-6b]----00.0-[02-6b]--+-00.0-[03]----00.0 TBT controller
+-01.0-[04-36]-- DS hotplug port
+-02.0-[37]----00.0 xHCI controller
\-04.0-[38-6b]-- DS hotplug port
The root port (1b.0) and the PCIe switch downstream ports are all PCIe Gen3
so they support 8GT/s link speeds.
We wait for the PCIe hierarchy to enter D3cold (runtime):
pcieport 0000:00:1b.0: power state changed by ACPI to D3cold
When it wakes up from D3cold, according to the PCIe 5.0 section 5.8 the
PCIe switch is put to reset and its power is re-applied. This means that we
must follow the rules in PCIe 5.0 section 6.6.1.
For the PCIe Gen3 ports we are dealing with here, the following applies:
With a Downstream Port that supports Link speeds greater than 5.0 GT/s,
software must wait a minimum of 100 ms after Link training completes
before sending a Configuration Request to the device immediately below
that Port. Software can determine when Link training completes by polling
the Data Link Layer Link Active bit or by setting up an associated
interrupt (see Section 6.7.3.3).
Translating this into the above topology we would need to do this (DLLLA
stands for Data Link Layer Link Active):
0000:00:1b.0: wait for 100 ms after DLLLA is set before access to 0000:01:00.0
0000:02:00.0: wait for 100 ms after DLLLA is set before access to 0000:03:00.0
0000:02:02.0: wait for 100 ms after DLLLA is set before access to 0000:37:00.0
I've instrumented the kernel with some additional logging so we can see the
actual delays performed:
pcieport 0000:00:1b.0: power state changed by ACPI to D0
pcieport 0000:00:1b.0: waiting for D3cold delay of 100 ms
pcieport 0000:00:1b.0: waiting for D3hot delay of 10 ms
pcieport 0000:02:01.0: waiting for D3hot delay of 10 ms
pcieport 0000:02:04.0: waiting for D3hot delay of 10 ms
For the switch upstream port (01:00.0 reachable through 00:1b.0 root port)
we wait for 100 ms but not taking into account the DLLLA requirement. We
then wait 10 ms for D3hot -> D0 transition of the root port and the two
downstream hotplug ports. This means that we deviate from what the spec
requires.
Performing the same check for system sleep (s2idle) transitions it turns
out to be even worse. None of the mandatory delays are performed. If this
would be S3 instead of s2idle then according to PCI FW spec 3.2 section
4.6.8. there is a specific _DSM that allows the OS to skip the delays but
this platform does not provide the _DSM and does not go to S3 anyway so no
firmware is involved that could already handle these delays.
On this particular platform these delays are not actually needed because
there is an additional delay as part of the ACPI power resource that is
used to turn on power to the hierarchy but since that additional delay is
not required by any of standards (PCIe, ACPI) it is not present in the
Intel Ice Lake, for example where missing the mandatory delays causes
pciehp to start tearing down the stack too early (links are not yet
trained). Below is an example how it looks like when this happens:
pcieport 0000:83:04.0: pciehp: Slot(4): Card not present
pcieport 0000:87:04.0: PME# disabled
pcieport 0000:83:04.0: pciehp: pciehp_unconfigure_device: domain🚌dev = 0000:86:00
pcieport 0000:86:00.0: Refused to change power state, currently in D3
pcieport 0000:86:00.0: restoring config space at offset 0x3c (was 0xffffffff, writing 0x201ff)
pcieport 0000:86:00.0: restoring config space at offset 0x38 (was 0xffffffff, writing 0x0)
...
There is also one reported case (see the bugzilla link below) where the
missing delay causes xHCI on a Titan Ridge controller fail to runtime
resume when USB-C dock is plugged. This does not involve pciehp but instead
the PCI core fails to runtime resume the xHCI device:
pcieport 0000:04:02.0: restoring config space at offset 0xc (was 0x10000, writing 0x10020)
pcieport 0000:04:02.0: restoring config space at offset 0x4 (was 0x100000, writing 0x100406)
xhci_hcd 0000:39:00.0: Refused to change power state, currently in D3
xhci_hcd 0000:39:00.0: restoring config space at offset 0x3c (was 0xffffffff, writing 0x1ff)
xhci_hcd 0000:39:00.0: restoring config space at offset 0x38 (was 0xffffffff, writing 0x0)
...
Add a new function pci_bridge_wait_for_secondary_bus() that is called on
PCI core resume and runtime resume paths accordingly if the bridge entered
D3cold (and thus went through reset).
This is second attempt to add the missing delays. The previous solution in
c2bf1fc212 ("PCI: Add missing link delays required by the PCIe spec") was
reverted because of two issues it caused:
1. One system become unresponsive after S3 resume due to PME service
spinning in pcie_pme_work_fn(). The root port in question reports that
the xHCI sent PME but the xHCI device itself does not have PME status
set. The PME status bit is never cleared in the root port resulting
the indefinite loop in pcie_pme_work_fn().
2. Slows down resume if the root/downstream port does not support Data
Link Layer Active Reporting because pcie_wait_for_link_delay() waits
1100 ms in that case.
This version should avoid the above issues because we restrict the delay to
happen only if the port went into D3cold.
Link: https://lore.kernel.org/linux-pci/SL2P216MB01878BBCD75F21D882AEEA2880C60@SL2P216MB0187.KORP216.PROD.OUTLOOK.COM/
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203885
Link: https://lore.kernel.org/r/20191112091617.70282-3-mika.westerberg@linux.intel.com
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add pcie_wait_for_link_delay(). Similar to pcie_wait_for_link() but allows
passing custom activation delay in milliseconds.
Link: https://lore.kernel.org/r/20191112091617.70282-2-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pci_raw_set_power_state() uses the Power Management capability to change a
device's power state. The capability is in config space, which is
accessible in D0, D1, D2, and D3hot, but not in D3cold.
If we call pci_raw_set_power_state() on a device that's in D3cold, config
reads fail and return ~0 data, which we erroneously interpreted as "the
device is in D3hot", leading to messages like this:
pcieport 0000:03:00.0: Refused to change power state, currently in D3
The PCI_PM_CTRL has several RsvdP fields, so ~0 is never a valid register
value. If we get that value, print a more informative message and return
an error.
Changing the power state of a device from D3cold must be done by a platform
power management method or some other non-config space mechanism.
Link: https://lore.kernel.org/r/20190822200551.129039-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use pci_power_name() to print pci_power_t correctly. This changes:
"state 0" or "D0" to "D0"
"state 1" or "D1" to "D1"
"state 2" or "D2" to "D2"
"state 3" or "D3" to "D3hot"
"state 4" or "D4" to "D3cold"
Changes dmesg logging only, no other functional change intended.
Link: https://lore.kernel.org/r/20190822200551.129039-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Because pci_set_power_state() has become the only caller of
__pci_complete_power_transition(), there is no need for the latter to
be a separate function any more, so fold it into the former, drop a
redundant check and reduce the number of lines of code somewhat.
Code rearrangement, no intentional functional impact.
Link: https://lore.kernel.org/r/15576968.k611qn3UU0@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Notice that radeon_set_suspend(), which is the only caller of
__pci_complete_power_transition() outside of pci.c, really only
cares about the pci_platform_power_transition() invoked by it,
so export the latter instead of it, update the radeon driver to
call pci_platform_power_transition() directly and make
__pci_complete_power_transition() static.
Code rearrangement, no intentional functional impact.
Link: https://lore.kernel.org/r/1731661.ykamz2Tiuf@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Because pci_power_up() has become the only caller of
__pci_start_power_transition(), there is no need for the latter to
be a separate function any more, so fold it into the former, drop a
redundant check and reduce the number of lines of code somewhat.
Code rearrangement, no intentional functional impact.
Link: https://lore.kernel.org/r/3458080.lsoDbfkST9@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Make it explicitly clear that the code to put devices into D0 in
pci_set_power_state() and in pci_pm_default_resume_early() is the
same by making the latter use pci_power_up() for transitions into D0.
Code rearrangement, no intentional functional impact.
Link: https://lore.kernel.org/r/2520019.OZ1nXS5aSj@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Move the invocation of pci_update_current_state() from pci_power_up() to
pci_pm_default_resume_early(), which is the only caller of that function.
Preparatory change, no functional impact.
Link: https://lore.kernel.org/r/37482337.udjOGdOKNb@kreacher
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The struct pci_driver.suspend_late() hook is one of the legacy PCI power
management callbacks, and there are no remaining users of it. Remove it.
Link: https://lore.kernel.org/r/20191101204558.210235-7-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The struct pci_driver.resume_early() hook is one of the legacy PCI power
management callbacks, and there are no remaining users of it. Remove it.
Link: https://lore.kernel.org/r/20191101204558.210235-6-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Check for the PCI_DEV_FLAGS_NO_D3 quirk early, before calling
__pci_start_power_transition(). This way all the cases where we don't need
to do anything at all are checked up front.
This doesn't fix anything because if the caller requested D3hot or D3cold,
__pci_start_power_transition() is a no-op. But calling it is pointless and
makes the code harder to analyze.
Link: https://lore.kernel.org/r/20191101204558.210235-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pci_pm_reset() resets a device by putting it in D3hot and bringing it back
to D0. Clarify related messages to mention "D3hot" explicitly instead of
just "D3".
Link: https://lore.kernel.org/r/20191101204558.210235-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PCI_PM_D2_DELAY is defined as 200, which is milliseconds, but previously we
used udelay(), which only waited for 200 microseconds. Use msleep()
instead so we wait the correct amount of time. See PCIe r5.0, sec 5.9.
Link: https://lore.kernel.org/r/20191101204558.210235-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use the PCI dev_printk() wrappers for consistency with the rest of the PCI
core. No functional change intended.
Link: https://lore.kernel.org/r/20191017212851.54237-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some of the power management ops use this style:
struct device_driver *drv = dev->driver;
if (drv && drv->pm && drv->pm->prepare(dev))
drv->pm->prepare(dev);
while others use this:
const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
if (pm && pm->runtime_resume)
pm->runtime_resume(dev);
Convert the first style to the second so they're all consistent. Remove
local "error" variables when unnecessary. No functional change intended.
Link: https://lore.kernel.org/r/20191014230016.240912-6-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pci_pm_resume() and pci_pm_restore() call pci_pm_default_resume(), which
runs resume fixups before disabling wakeup events:
static void pci_pm_default_resume(struct pci_dev *pci_dev)
{
pci_fixup_device(pci_fixup_resume, pci_dev);
pci_enable_wake(pci_dev, PCI_D0, false);
}
pci_pm_runtime_resume() does both of these, but in the opposite order:
pci_enable_wake(pci_dev, PCI_D0, false);
pci_fixup_device(pci_fixup_resume, pci_dev);
We should always use the same ordering unless there's a reason to do
otherwise. Change pci_pm_runtime_resume() to call pci_pm_default_resume()
instead of open-coding this, so the fixups are always done before disabling
wakeup events.
pci_pm_default_resume() is called from pci_pm_runtime_resume(), which is
under #ifdef CONFIG_PM. If SUSPEND and HIBERNATION are disabled, PM_SLEEP
is disabled also, so move pci_pm_default_resume() from #ifdef
CONFIG_PM_SLEEP to #ifdef CONFIG_PM.
Link: https://lore.kernel.org/r/20191014230016.240912-5-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Previously, pci_pm_resume_noirq() cleared the PME Status bit in the Root
Status register only if the device had no driver or the driver did not
implement legacy power management. It should clear PME Status regardless
of what sort of power management the driver supports, so do this before
checking for legacy power management.
This affects Root Ports and Root Complex Event Collectors, for which the
usual driver is the PCIe portdrv, which implements new power management, so
this change is just on principle, not to fix any actual defects.
Fixes: a39bd851dc ("PCI/PM: Clear PCIe PME Status bit in core, not PCIe port driver")
Link: https://lore.kernel.org/r/20191014230016.240912-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pci_pm_thaw_noirq() is supposed to return the device to D0 and restore its
configuration registers, but previously it only did that for devices whose
drivers implemented the new power management ops.
Hibernation, e.g., via "echo disk > /sys/power/state", involves freezing
devices, creating a hibernation image, thawing devices, writing the image,
and powering off. The fact that thawing did not return devices with legacy
power management to D0 caused errors, e.g., in this path:
pci_pm_thaw_noirq
if (pci_has_legacy_pm_support(pci_dev)) # true for Mellanox VF driver
return pci_legacy_resume_early(dev) # ... legacy PM skips the rest
pci_set_power_state(pci_dev, PCI_D0)
pci_restore_state(pci_dev)
pci_pm_thaw
if (pci_has_legacy_pm_support(pci_dev))
pci_legacy_resume
drv->resume
mlx4_resume
...
pci_enable_msix_range
...
if (dev->current_state != PCI_D0) # <---
return -EINVAL;
which caused these warnings:
mlx4_core a6d1:00:02.0: INTx is not supported in multi-function mode, aborting
PM: dpm_run_callback(): pci_pm_thaw+0x0/0xd7 returns -95
PM: Device a6d1:00:02.0 failed to thaw: error -95
Return devices to D0 and restore config registers for all devices, not just
those whose drivers support new power management.
[bhelgaas: also call pci_restore_state() before pci_legacy_resume_early(),
update comment, add stable tag, commit log]
Link: https://lore.kernel.org/r/KU1P153MB016637CAEAD346F0AA8E3801BFAD0@KU1P153MB0166.APCP153.PROD.OUTLOOK.COM
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org # v4.13+
The 0V9 and 1V8 supplies power the PCIe block in the SoC itself, and
are thus fundamental to PCIe being usable at all. As such, it makes
sense to treat them as non-optional and rely on dummy regulators if
not explicitly described.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Now that all the PCI host drivers are using pci_parse_request_of_pci_ranges(),
make devm_of_pci_get_host_bridge_resources() static.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that the helpers provide the inbound resources in the host bridge
'dma_ranges' resource list, convert Renesas R-Car PCIe host bridge to
use the resource list to setup the inbound addresses.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that the helpers provide the inbound resources in the host bridge
'dma_ranges' resource list, convert Broadcom iProc host bridge to use
the resource list to setup the inbound addresses.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Now that the helpers provide the inbound resources in the host bridge
'dma_ranges' resource list, convert the Xgene host bridge to use the
resource list to setup the inbound addresses.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that the helpers provide the inbound resources in the host bridge
'dma_ranges' resource list, convert the v3-semi host bridge to use
the resource list to setup the inbound addresses.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that the helpers provide the inbound resources in the host bridge
'dma_ranges' resource list, convert Faraday ftpci100 host bridge to use
the resource list to setup the inbound addresses.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Extend devm_of_pci_get_host_bridge_resources() and
pci_parse_request_of_pci_ranges() helpers to also parse the inbound
addresses from DT 'dma-ranges' and populate a resource list with the
translated addresses. This will help ensure 'dma-ranges' is always
parsed in a consistent way.
Tested-by: Srinath Mannam <srinath.mannam@broadcom.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> # for AArdvark
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Will Deacon <will@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Tom Joseph <tjoseph@cadence.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: rfi@lists.rocketboards.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
This patch adds support for this VMD device which supports the bus
restriction mode.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
VMD bus restrictions are required when IO fabric is multiplexed such
that VMD cannot use the entire bus range. This patch adds another bus
restriction decode bit that can be set by firmware to restrict the VMD
bus range to between 224-255.
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Most of the ACS quirks have a similar pattern of:
acs_flags &= ~( <controls provided by this device> );
return acs_flags ? 0 : 1;
Pull this out into a helper function to simplify the quirks slightly. The
helper function is also a convenient place for comments about what the list
of ACS controls means. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
The ACS quirks differ in needless ways, which makes them look more
different than they really are.
Reorder the ACS flags in order of definitions in the spec:
PCI_ACS_SV Source Validation
PCI_ACS_TB Translation Blocking
PCI_ACS_RR P2P Request Redirect
PCI_ACS_CR P2P Completion Redirect
PCI_ACS_UF Upstream Forwarding
PCI_ACS_EC P2P Egress Control
PCI_ACS_DT Direct Translated P2P
(PCIe r5.0, sec 7.7.8.2) and use similar code structure in all. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
As per PCIe r5.0, sec 7.8.5.2, fixed bus numbers of a bridge must be zero
when no function that uses EA is located behind it. Hence, if EA supplies
bus numbers of zero, assign bus numbers normally. A secondary bus can
never have a bus number of zero, so setting a bridge's Secondary Bus Number
to zero makes downstream devices unreachable.
[bhelgaas: retain bool return value so "zero is invalid" logic is local]
Fixes: 2dbce59011 ("PCI: Assign bus numbers present in EA capability for bridges")
Link: https://lore.kernel.org/r/1572850664-9861-1-git-send-email-sundeep.lkml@gmail.com
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v5.2+
Previously, the kernel sometimes assigned more MMIO or MMIO_PREF space than
desired. For example, if the user requested 128M of space with
"pci=realloc,hpmemsize=128M", we sometimes assigned 256M:
pci 0000:06:01.0: BAR 14: assigned [mem 0x90100000-0xa00fffff] = 256M
pci 0000:06:04.0: BAR 14: assigned [mem 0xa0200000-0xb01fffff] = 256M
With this patch applied:
pci 0000:06:01.0: BAR 14: assigned [mem 0x90100000-0x980fffff] = 128M
pci 0000:06:04.0: BAR 14: assigned [mem 0x98200000-0xa01fffff] = 128M
This happened when in the first pass, the MMIO_PREF succeeded but the MMIO
failed. In the next pass, because MMIO_PREF was already assigned, the
attempt to assign MMIO_PREF returned an error code instead of success
(nothing more to do, already allocated). Hence, the size which was actually
allocated, but thought to have failed, was placed in the MMIO window.
The bug resulted in the MMIO_PREF being added to the MMIO window, which
meant doubling if MMIO_PREF size = MMIO size. With a large MMIO_PREF, the
MMIO window would likely fail to be assigned altogether due to lack of
32-bit address space.
Change find_free_bus_resource() to do the following:
- Return first unassigned resource of the correct type.
- If there is none, return first assigned resource of the correct type.
- If none of the above, return NULL.
Returning an assigned resource of the correct type allows the caller to
distinguish between already assigned and no resource of the correct type.
Add checks in pbus_size_io() and pbus_size_mem() to return success if
resource returned from find_free_bus_resource() is already allocated.
This avoids pbus_size_io() and pbus_size_mem() returning error code to
__pci_bus_size_bridges() when a resource has been successfully assigned in
a previous pass. This fixes the existing behaviour where space for a
resource could be reserved multiple times in different parent bridge
windows.
Link: https://lore.kernel.org/lkml/20190531171216.20532-2-logang@deltatee.com/T/#u
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203243
Link: https://lore.kernel.org/r/PS2P216MB075563AA6AD242AA666EDC6A80760@PS2P216MB0755.KORP216.PROD.OUTLOOK.COM
Reported-by: Kit Chow <kchow@gigaio.com>
Reported-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Valerio and others reported that commit 84c8b58ed3 ("ACPI / hotplug /
PCI: Don't scan bridges managed by native hotplug") prevents some recent
LG and HP laptops from booting with endless loop of:
ACPI Error: No handler or method for GPE 08, disabling event (20190215/evgpe-835)
ACPI Error: No handler or method for GPE 09, disabling event (20190215/evgpe-835)
ACPI Error: No handler or method for GPE 0A, disabling event (20190215/evgpe-835)
...
What seems to happen is that during boot, after the initial PCI enumeration
when EC is enabled the platform triggers ACPI Notify() to one of the root
ports. The root port itself looks like this:
pci 0000:00:1b.0: PCI bridge to [bus 02-3a]
pci 0000:00:1b.0: bridge window [mem 0xc4000000-0xda0fffff]
pci 0000:00:1b.0: bridge window [mem 0x80000000-0xa1ffffff 64bit pref]
The BIOS has configured the root port so that it does not have I/O bridge
window.
Now when the ACPI Notify() is triggered ACPI hotplug handler calls
acpiphp_native_scan_bridge() for each non-hotplug bridge (as this system is
using native PCIe hotplug) and pci_assign_unassigned_bridge_resources() to
allocate resources.
The device connected to the root port is a PCIe switch (Thunderbolt
controller) with two hotplug downstream ports. Because of the hotplug ports
__pci_bus_size_bridges() tries to add "additional I/O" of 256 bytes to each
(DEFAULT_HOTPLUG_IO_SIZE). This gets further aligned to 4k as that's the
minimum I/O window size so each hotplug port gets 4k I/O window and the
same happens for the root port (which is also hotplug port). This means
3 * 4k = 12k I/O window.
Because of this pci_assign_unassigned_bridge_resources() ends up opening a
I/O bridge window for the root port at first available I/O address which
seems to be in range 0x1000 - 0x3fff. Normally this range is used for ACPI
stuff such as GPE bits (below is part of /proc/ioports):
1800-1803 : ACPI PM1a_EVT_BLK
1804-1805 : ACPI PM1a_CNT_BLK
1808-180b : ACPI PM_TMR
1810-1815 : ACPI CPU throttle
1850-1850 : ACPI PM2_CNT_BLK
1854-1857 : pnp 00:05
1860-187f : ACPI GPE0_BLK
However, when the ACPI Notify() happened this range was not yet reserved
for ACPI/PNP (that happens later) so PCI gets it. It then starts writing to
this range and accidentally stomps over GPE bits among other things causing
the endless stream of messages about missing GPE handler.
This problem does not happen if "pci=hpiosize=0" is passed in the kernel
command line. The reason is that then the kernel does not try to allocate
the additional 256 bytes for each hotplug port.
Fix this by allocating resources directly below the non-hotplug bridges
where a new device may appear as a result of ACPI Notify(). This avoids the
hotplug bridges and prevents opening the additional I/O window.
Fixes: 84c8b58ed3 ("ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203617
Link: https://lore.kernel.org/r/20191030150545.19885-1-mika.westerberg@linux.intel.com
Reported-by: Valerio Passini <passini.valerio@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: stable@vger.kernel.org
The newer ibm,drc-info property is a condensed description of the old
ibm,drc-* properties (ie. names, types, indexes, and power-domains).
When matching a drc-index to a drc-name we need to verify that the
index is within the start and last drc-index range and map it to a
drc-name using the drc-name-prefix and logical index.
Fix the mapping by checking that the index is within the range of the
current drc-info entry, and build the name from the drc-name-prefix
concatenated with the starting drc-name-suffix value and the sequential
index obtained by subtracting ibm,my-drc-index from this entries
drc-start-index.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-10-git-send-email-tyreld@linux.ibm.com
The device tree is in big endian format and any properties directly
retrieved using OF helpers that don't explicitly byte swap should
be annotated. In particular there are several places where we grab
the opaque property value for the old ibm,drc-* properties and the
ibm,my-drc-index property.
Fix this for better static checking by annotating values we know to
explicitly big endian, and byte swap where appropriate.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-9-git-send-email-tyreld@linux.ibm.com
Split physical PCI slot registration scanning into separate routines
that support the old ibm,drc-* properties and one that supports the
new compressed ibm,drc-info property.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-7-git-send-email-tyreld@linux.ibm.com
In the event that the partition is migrated to a platform with older
firmware that doesn't support the ibm,drc-info property the device
tree is modified to remove the ibm,drc-info property and replace it
with the older style ibm,drc-* properties for types, names, indexes,
and power-domains. One of the requirements of the drc-info firmware
feature is that the client is able to handle both the new property,
and old style properties at runtime. Therefore we can't rely on the
firmware feature alone to dictate which property is currently
present in the device tree.
Fix this short coming by checking explicitly for the ibm,drc-info
property, and falling back to the older ibm,drc-* properties if it
doesn't exist.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-6-git-send-email-tyreld@linux.ibm.com
The first entry of the ibm,drc-info property is an int encoded count
of the number of drc-info entries that follow. The "value" pointer
returned by of_prop_next_u32() is still pointing at the this value
when we call of_read_drc_info_cell(), but the helper function
expects that value to be pointing at the first element of an entry.
Fix up by incrementing the "value" pointer to point at the first
element of the first drc-info entry prior.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1573449697-5448-5-git-send-email-tyreld@linux.ibm.com
This addresses deadlocks in these common cases in hierarchies containing
two switches:
- All involved ports are runtime suspended and they are unplugged. This
can happen easily if the drivers involved automatically enable runtime
PM (xHCI for example does that).
- System is suspended (e.g., closing the lid on a laptop) with a dock +
something else connected, and the dock is unplugged while suspended.
These cases lead to the following deadlock:
INFO: task irq/126-pciehp:198 blocked for more than 120 seconds.
irq/126-pciehp D 0 198 2 0x80000000
Call Trace:
schedule+0x2c/0x80
schedule_timeout+0x246/0x350
wait_for_completion+0xb7/0x140
kthread_stop+0x49/0x110
free_irq+0x32/0x70
pcie_shutdown_notification+0x2f/0x50
pciehp_remove+0x27/0x50
pcie_port_remove_service+0x36/0x50
device_release_driver+0x12/0x20
bus_remove_device+0xec/0x160
device_del+0x13b/0x350
device_unregister+0x1a/0x60
remove_iter+0x1e/0x30
device_for_each_child+0x56/0x90
pcie_port_device_remove+0x22/0x40
pcie_portdrv_remove+0x20/0x60
pci_device_remove+0x3e/0xc0
device_release_driver_internal+0x18c/0x250
device_release_driver+0x12/0x20
pci_stop_bus_device+0x6f/0x90
pci_stop_bus_device+0x31/0x90
pci_stop_and_remove_bus_device+0x12/0x20
pciehp_unconfigure_device+0x88/0x140
pciehp_disable_slot+0x6a/0x110
pciehp_handle_presence_or_link_change+0x263/0x400
pciehp_ist+0x1c9/0x1d0
irq_thread_fn+0x24/0x60
irq_thread+0xeb/0x190
kthread+0x120/0x140
INFO: task irq/190-pciehp:2288 blocked for more than 120 seconds.
irq/190-pciehp D 0 2288 2 0x80000000
Call Trace:
__schedule+0x2a2/0x880
schedule+0x2c/0x80
schedule_preempt_disabled+0xe/0x10
mutex_lock+0x2c/0x30
pci_lock_rescan_remove+0x15/0x20
pciehp_unconfigure_device+0x4d/0x140
pciehp_disable_slot+0x6a/0x110
pciehp_handle_presence_or_link_change+0x263/0x400
pciehp_ist+0x1c9/0x1d0
irq_thread_fn+0x24/0x60
irq_thread+0xeb/0x190
kthread+0x120/0x140
What happens here is that the whole hierarchy is runtime resumed and the
parent PCIe downstream port, which got the hot-remove event, starts
removing devices below it, taking pci_lock_rescan_remove() lock. When the
child PCIe port is runtime resumed it calls pciehp_check_presence() which
ends up calling pciehp_card_present() and pciehp_check_link_active(). Both
of these use pcie_capability_read_word(), which notices that the underlying
device is already gone and returns PCIBIOS_DEVICE_NOT_FOUND with the
capability value set to 0. When pciehp gets this value it thinks that its
child device is also hot-removed and schedules its IRQ thread to handle the
event.
The deadlock happens when the child's IRQ thread runs and tries to acquire
pci_lock_rescan_remove() which is already taken by the parent and the
parent waits for the child's IRQ thread to finish.
Prevent this from happening by checking the return value of
pcie_capability_read_word() and if it is PCIBIOS_DEVICE_NOT_FOUND stop
performing any hot-removal activities.
[bhelgaas: add common scenarios to commit log]
Link: https://lore.kernel.org/r/20191029170022.57528-2-mika.westerberg@linux.intel.com
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We try to keep PCIe hotplug ports runtime suspended when entering system
suspend. Because the PCIe portdrv sets the DPM_FLAG_NEVER_SKIP flag, the PM
core always calls system suspend/resume hooks even if the device is left
runtime suspended. Since PCIe hotplug driver re-used the same function for
both runtime suspend and system suspend, it ended up disabling hotplug
interrupt twice and the second time following was printed:
pciehp 0000:03:01.0:pcie204: pcie_do_write_cmd: no response from device
Prevent this from happening by checking whether the device is already
runtime suspended when the system suspend hook is called.
Fixes: 9c62f0bfb8 ("PCI: pciehp: Implement runtime PM callbacks")
Link: https://lore.kernel.org/r/20191029170022.57528-1-mika.westerberg@linux.intel.com
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The R-Car Gen2/3 manual - available at:
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg1m.html#documents
"RZ/G Series User's Manual: Hardware" section
strictly enforces the MACCTLR inizialization value - 39.3.1 - "Initial
Setting of PCI Express":
"Be sure to write the initial value (= H'80FF 0000) to MACCTLR before
enabling PCIETCTLR.CFINIT".
To avoid unexpected behavior and to match the SW initialization sequence
guidelines, this patch programs the MACCTLR with the correct value.
Note that the MACCTLR.SPCHG bit in the MACCTLR register description
reports that "Only writing 1 is valid and writing 0 is invalid" but this
"invalid" has to be interpreted as a write-ignore aka "ignored", not
"prohibited".
Reported-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Fixes: c25da47788 ("PCI: rcar: Add Renesas R-Car PCIe driver")
Fixes: be20bbcb0a ("PCI: rcar: Add the initialization of PCIe link in resume_noirq()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: <stable@vger.kernel.org> # v5.2+
Infinite timeout loops are hard to read. Refactor it to plausible 'do {}
while ()'.
Note, the supplied timeout can't be negative for current use, though if
it's not dividable to 10, we may go below 0, that's why type of the
parameter is int. And thus, we may move the check to the loop condition.
No functional change intended.
Link: https://lore.kernel.org/r/20191108111855.85866-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Enhance the ACS quirk for Cavium Processors. Add the root port vendor IDs
for ThunderX2 and ThunderX3 series of processors.
[bhelgaas: add Fixes: and stable tag]
Fixes: f2ddaf8dfd ("PCI: Apply Cavium ThunderX ACS quirk to more Root Ports")
Link: https://lore.kernel.org/r/20191111024243.GA11408@dc5-eodlnx05.marvell.com
Signed-off-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Robert Richter <rrichter@marvell.com>
Cc: stable@vger.kernel.org # v4.12+
Cadence core library files may be used by various platform drivers.
Add a new directory "cadence" to group all the Cadence core library files
and the platforms using Cadence core library.
Signed-off-by: Tom Joseph <tjoseph@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cadence PCIe host and endpoint IP may be embedded into a variety of
SoCs/platforms. Let's extract the platform related APIs/Structures in the
current driver to a separate file (pcie-cadence-plat.c), such that the
common functionality can be used by future platforms.
Signed-off-by: Tom Joseph <tjoseph@cadence.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Due to hardware constraints, the size of each inbound range entry
populated into the controller cannot be larger than the alignment
of the entry's start address. Currently, the alignment for each
"dma-ranges" inbound range is calculated only once for each range
and the increment for programming the controller is also derived
from it only once. Thus, a "dma-ranges" entry describing a memory
at 0x48000000 and size 0x38000000 would lead to multiple controller
entries, each 0x08000000 long.
This is inefficient, especially considering that by adding the size
to the start address, the alignment increases. This patch moves the
alignment calculation into the loop populating the controller entries,
thus updating the alignment for each controller entry.
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
Since the 'idx' variable value is stored across multiple calls to
rcar_pcie_inbound_ranges() function, and the 'idx' value is used to
index registers which are written, subsequent calls might cause
the 'idx' value to be high enough to trigger writes into nonexistent
registers.
Fix this by moving the 'idx' value check to the beginning of the loop.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
Remove unnecessary header include (../pci.h) since it doesn't
provide any needed symbols.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for the LS1028a PCIe controller.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <Andrew.Murray@arm.com>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
Since commit a574795bc3 ("PCI: generic,versatile: Remove unused
pci_sys_data structures") the build dependency on ARM is gone, so let's
enable COMPILE_TEST for versatile.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
PHYS_OFFSET is not universally defined on all arches and using it prevents
enabling COMPILE_TEST. PAGE_OFFSET and __pa() are always available, so use
them to get the physical start of memory address.
This should have probably used 'dma-ranges' to get the address, but we
don't want to force a DT update to do that. At least in QEMU, the SMAP
registers have no effect (or perhaps the only value that is handled is 0).
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert ARM Versatile host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert the xilinx-nwl host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Convert the Xilinx host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Convert the xgene host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert V3 host bridge to use the common
pci_parse_request_of_pci_ranges().
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The Rockchip host bridge driver doesn't need to store outboard resources
in its private struct as they are already stored in struct
pci_host_bridge.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Convert the Rockchip host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Convert the Mobiveil host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert Mediatek host bridge to use the common
pci_parse_request_of_pci_ranges().
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-mediatek@lists.infradead.org
Convert the iProc host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list, so just use
bridge->windows directly.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Convert the Faraday host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert the Designware host bridge to use the common
pci_parse_request_of_pci_ranges().
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Convert altera host bridge to use the common
pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
If an I/O range is present, then it will now be mapped. It's expected
that h/w which doesn't support I/O range will not define one.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: rfi@lists.rocketboards.org
Convert aardvark to use the common pci_parse_request_of_pci_ranges().
There's no need to assign the resources to a temporary list first. Just
use bridge->windows directly and remove all the temporary list handling.
Tested-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
pci_parse_request_of_pci_ranges() is missing a module export, so add it.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Prior to eed85ff4c0 ("PCI/DPC: Enable DPC only if AER is available"),
Linux handled DPC events regardless of whether firmware had granted it
ownership of AER or DPC, e.g., via _OSC.
PCIe r5.0, sec 6.2.10, recommends that the OS link control of DPC to
control of AER, so after eed85ff4c0, Linux handles DPC events only if it
has control of AER.
On platforms that do not grant OS control of AER via _OSC, Linux DPC
handling worked before eed85ff4c0 but not after.
To make Linux DPC handling work on those platforms the same way they did
before, add a "pcie_ports=dpc-native" kernel parameter that makes Linux
handle DPC events regardless of whether it has control of AER.
[bhelgaas: commit log, move pcie_ports_dpc_native to drivers/pci/]
Link: https://lore.kernel.org/r/20191023192205.97024-1-olof@lixom.net
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Invalidate PAXB inbound/outbound address mapping on probe before
programming it.
Kernel relies on outbound/inbound windows VALID bit in OARR registers to
detect if a window was programmed and if it is set it does not overwrite
it.
This causes issues on soft reboot (eg kexec) since the host controller
does not go through a HW reset on softboot so the kernel detects valid
outbound/inbound windows configuration and is not able to reprogramme
it as expected.
Therefore, in order to make sure outbound/inbound windows are
reprogrammed on soft reboot (eg kexec), invalidate memory windows on
each probe to fix the issue.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
In pci_call_probe(), we try to run driver probe functions on the node where
the device is attached. If we don't know which node the device is attached
to, the driver will likely run on the wrong node. This will still work,
but performance will not be as good as it could be.
On NUMA systems, warn if we don't know which node a PCI host bridge is
attached to. This is likely an indication that ACPI didn't supply a _PXM
method or the DT didn't supply a "numa-node-id" property.
[bhelgaas: commit log, check bus node]
Link: https://lore.kernel.org/r/1571467543-26125-1-git-send-email-linyunsheng@huawei.com
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The existing "pci=hpmemsize=nn[KMG]" kernel parameter overrides the default
size of both the non-prefetchable and the prefetchable MMIO windows for
hotplug bridges.
Add "pci=hpmmiosize=nn[KMG]" to override the default size of only the
non-prefetchable MMIO window.
Add "pci=hpmmioprefsize=nn[KMG]" to override the default size of only the
prefetchable MMIO window.
Link: https://lore.kernel.org/r/SL2P216MB0187E4D0055791957B7E2660806B0@SL2P216MB0187.KORP216.PROD.OUTLOOK.COM
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The .ioctl and .compat_ioctl file operations have the same prototype so
they can both point to the same function, which works great almost all
the time when all the commands are compatible.
One exception is the s390 architecture, where a compat pointer is only
31 bit wide, and converting it into a 64-bit pointer requires calling
compat_ptr(). Most drivers here will never run in s390, but since we now
have a generic helper for it, it's easy enough to use it consistently.
I double-checked all these drivers to ensure that all ioctl arguments
are used as pointers or are ignored, but are not interpreted as integer
values.
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Darren Hart (VMware) <dvhart@infradead.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A driver may want to know the existence of _PR3, to choose different
runtime suspend behavior. A user will be add in next patch.
This is mostly the same as nouveau_pr3_present().
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20191018073848.14590-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kernel-doc validator complains:
aer.c:207: warning: Function parameter or member 'str' not described in 'pcie_ecrc_get_policy'
aer.c:1209: warning: Function parameter or member 'irq' not described in 'aer_isr'
aer.c:1209: warning: Function parameter or member 'context' not described in 'aer_isr'
aer.c:1209: warning: Excess function parameter 'work' description in 'aer_isr'
Fix the above accordingly.
Link: https://lore.kernel.org/r/20190827151823.75312-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
The elements in the aer_uncorrectable_error_string[] refer to the bit names
in Uncorrectable Error Status Register. Add PoisonTLPBlocked, which was
added in PCIe r3.1, sec 7.10.2.
Link: https://lore.kernel.org/r/20190827222145.32642-1-rajatja@google.com
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we did not save and restore the AER configuration on
suspend/resume, so the configuration may be lost after resume.
Save the AER configuration during suspend and restore it during resume.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/92EBB4272BF81E4089A7126EC1E7B28492C3B007@IRSMSX101.ger.corp.intel.com
Signed-off-by: Mayurkumar Patel <mayurkumar.patel@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Corrects the programming to provide REFCLK to the downstream device
when there is no CLKREQ sideband signal routing present from root port
to the endpont.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Perform conversion to little-endian before every write to configuration
space and convert it back to CPU endianness on reads.
Additionally, initialise every multiple byte field of config space with
the cpu_to_le* macro, which is required since the structure describing
config space of emulated bridge assumes little-endian convention.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Initialise every multiple-byte field of emulated PCI bridge config
space with proper cpu_to_le* macro. This is required since the structure
describing config space of emulated bridge assumes little-endian
convention.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fix the return type of mvebu_pcie_map_registers in the
error path to have __iomem on it. Fixes the following
sparse warning:
drivers/pci/controller/pci-mvebu.c:716:31: warning: incorrect type in return expression (different address spaces)
drivers/pci/controller/pci-mvebu.c:716:31: expected void [noderef] <asn:2> *
drivers/pci/controller/pci-mvebu.c:716:31: got void *
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
The mvebu_pci_bridge_emul_ops is not exported outside
of the driver, so make it static to avoid the following
sparse warning:
drivers/pci/controller/pci-mvebu.c:557:28: warning: symbol 'mvebu_pci_bridge_emul_ops' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
There is an arbitrary difference between the system resume and
runtime resume code paths for PCI devices regarding the delay to
apply when switching the devices from D3cold to D0.
Namely, pci_restore_standard_config() used in the runtime resume
code path calls pci_set_power_state() which in turn invokes
__pci_start_power_transition() to power up the device through the
platform firmware and that function applies the transition delay
(as per PCI Express Base Specification Revision 2.0, Section 6.6.1).
However, pci_pm_default_resume_early() used in the system resume
code path calls pci_power_up() which doesn't apply the delay at
all and that causes issues to occur during resume from
suspend-to-idle on some systems where the delay is required.
Since there is no reason for that difference to exist, modify
pci_power_up() to follow pci_set_power_state() more closely and
invoke __pci_start_power_transition() from there to call the
platform firmware to power up the device (in case that's necessary).
Fixes: db288c9c5f ("PCI / PM: restore the original behavior of pci_set_power_state()")
Reported-by: Daniel Drake <drake@endlessm.com>
Tested-by: Daniel Drake <drake@endlessm.com>
Link: https://lore.kernel.org/linux-pm/CAD8Lp44TYxrMgPLkHCqF9hv6smEurMXvmmvmtyFhZ6Q4SE+dig@mail.gmail.com/T/#m21be74af263c6a34f36e0fc5c77c5449d9406925
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: 3.10+ <stable@vger.kernel.org> # 3.10+
When sriov_numvfs is being updated, we call the driver->sriov_configure()
function, which may enable VFs and call probe functions, which may make new
devices visible. This all happens before before sriov_numvfs_store()
updates sriov->num_VFs, so previously, concurrent sysfs reads of
sriov_numvfs returned stale values.
Serialize the sysfs read vs the write so the read returns the correct
num_VFs value.
[bhelgaas: hold device_lock instead of checking mutex_is_locked()]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202991
Link: https://lore.kernel.org/r/20190911072736.32091-1-pierre.cregut@orange.com
Signed-off-by: Pierre Crégut <pierre.cregut@orange.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Intel Visual Compute Accelerator (VCA) is a family of PCIe add-in devices
exposing computational units via Non Transparent Bridges (NTB, PEX 87xx).
Similarly to MIC x200, we need to add DMA aliases to allow buffer access
when IOMMU is enabled.
Add aliases to allow computational unit access to host memory. These
aliases mark the whole VCA device as one IOMMU group.
All possible slot numbers (0x20) are used, since we are unable to tell what
slot is used on other side. This quirk is intended for both host and
computational unit sides. The VCA devices have up to five functions: four
for DMA channels and one additional.
Link: https://lore.kernel.org/r/5683A335CC8BE1438C3C30C49DCC38DF637CED8E@IRSMSX102.ger.corp.intel.com
Signed-off-by: Slawomir Pawlowski <slawomir.pawlowski@intel.com>
Signed-off-by: Przemek Kitszel <przemyslawx.kitszel@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
According to documentation [0] the correct offset for the Upstream Peer
Decode Configuration Register (UPDCR) is 0x1014. It was previously defined
as 0x1114.
d99321b63b ("PCI: Enable quirks for PCIe ACS on Intel PCH root ports")
intended to enforce isolation between PCI devices allowing them to be put
into separate IOMMU groups. Due to the wrong register offset the intended
isolation was not fully enforced. This is fixed with this patch.
Please note that I did not test this patch because I have no hardware that
implements this register.
[0] https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/4th-gen-core-family-mobile-i-o-datasheet.pdf (page 325)
Fixes: d99321b63b ("PCI: Enable quirks for PCIe ACS on Intel PCH root ports")
Link: https://lore.kernel.org/r/7a3505df-79ba-8a28-464c-88b83eefffa6@kernkonzept.com
Signed-off-by: Steffen Liebergeld <steffen.liebergeld@kernkonzept.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Cc: stable@vger.kernel.org # v3.15+
These interfaces:
void pci_restore_pri_state(struct pci_dev *pdev);
void pci_restore_pasid_state(struct pci_dev *pdev);
are only used in drivers/pci and do not need to be seen by the rest of the
kernel. Most them to drivers/pci/pci.h so they're private to the PCI
subsystem.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The following functions are only used by the PCI core or by IOMMU drivers
that cannot be modular, so there's no need to export them at all:
pci_enable_ats()
pci_disable_ats()
pci_restore_ats_state()
pci_ats_queue_depth()
pci_ats_page_aligned()
pci_enable_pri()
pci_restore_pri_state()
pci_reset_pri()
pci_prg_resp_pasid_required()
pci_enable_pasid()
pci_disable_pasid()
pci_restore_pasid_state()
pci_pasid_features()
pci_max_pasids()
Remove the unnecessary EXPORT_SYMBOL_GPL()s.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The PRG Response PASID Required bit in the PRI Capability is read-only.
Read it once when we enumerate the device and cache the value so we don't
need to read it again.
Based-on-patch-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we didn't disable the PF ATS until all associated VFs had
disabled it. But per PCIe spec r5.0, sec 9.3.7.8, the ATS Capability in
VFs and associated PFs may be enabled independently. Leaving ATS enabled
in the PF unnecessarily may have power and performance impacts.
Remove this dependency logic in the ATS enable/disable code.
[bhelgaas: commit log]
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Link: https://lore.kernel.org/r/8163ab8fa66afd2cba514ae95d29ab12104781aa.1567029860.git.sathyanarayanan.kuppuswamy@linux.intel.com
Link: https://lore.kernel.org/r/20190905193146.90250-4-helgaas@kernel.org
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Per PCIe r5.0, sec 9.3.7.14, if a PF implements the PASID Capability, the
PF PASID configuration is shared by its VFs. VFs must not implement their
own PASID Capability. Since VFs don't have a PASID Capability,
pci_enable_pasid() always failed, which caused IOMMU setup to fail.
Update the PASID interfaces so for VFs they reflect the state of the PF
PASID.
[bhelgaas: rebase without pasid_cap caching, commit log]
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Link: https://lore.kernel.org/r/8ba1ac192e4ac737508b6ac15002158e176bab91.1567029860.git.sathyanarayanan.kuppuswamy@linux.intel.com
Link: https://lore.kernel.org/r/20190905193146.90250-3-helgaas@kernel.org
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Per PCIe r5.0, sec 9.3.7.11, VFs must not implement the PRI Capability. If
the PF implements PRI, it is shared by the VFs. Since VFs don't have a PRI
Capability, pci_enable_pri() always failed, which caused IOMMU setup to
fail.
Update the PRI interfaces so for VFs they reflect the state of the PF PRI.
[bhelgaas: rebase without pri_cap caching, commit log]
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Link: https://lore.kernel.org/r/b971e31f8695980da8e4a7f93e3b6a3edba3edaa.1567029860.git.sathyanarayanan.kuppuswamy@linux.intel.com
Link: https://lore.kernel.org/r/20190905193146.90250-2-helgaas@kernel.org
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
pci_prg_resp_pasid_required() returns the value of the "PRG Response PASID
Required" bit from the PRI capability, but the interface was previously
defined under #ifdef CONFIG_PCI_PASID.
Move it from CONFIG_PCI_PASID to CONFIG_PCI_PRI so it's with the other
PRI-related things.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Factor out getting the link associated with a pci_dev and use this helper
where appropriate. In addition this helper will be used in a subsequent
patch of this series.
Link: https://lore.kernel.org/r/19d33770-29de-a9af-4d85-f2b30269d383@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously Clock PM could not be re-enabled after being disabled by
pci_disable_link_state() because clkpm_capable was reset. Change this by
adding a clkpm_disable field similar to aspm_disable.
Link: https://lore.kernel.org/r/4e8a66db-7d53-4a66-c26c-f0037ffaa705@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for disabling states L1.1 and L1.2 to pci_disable_link_state().
Allow separate control of ASPM and PCI PM L1 substates.
Link: https://lore.kernel.org/r/d81f8036-c236-6463-48e7-ebcdcda85bba@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The lifetime of the link_state structure (bridge->link_state) is not the
same as the lifetime of "bridge" itself. The link_state is allocated by
pcie_aspm_init_link_state() after children of the bridge have been
enumerated, and it is deallocated by pcie_aspm_exit_link_state() after all
children of the bridge (but not the bridge itself) have been removed.
Previously pcie_aspm_enabled() acquired aspm_lock to ensure that
link_state was not deallocated while we're looking at it. But the fact
that the caller of pcie_aspm_enabled() holds a reference to @pdev means
there's always at least one child of the bridge, which means link_state
can't be deallocated.
Remove the unnecessary locking in pcie_aspm_enabled().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
find_next_bit() takes a parameter of size long, and performs arithmetic
that assumes that the argument is of size long.
Therefore we cannot pass a u32, since this will cause find_next_bit()
to read outside the stack buffer and will produce the following print:
BUG: KASAN: stack-out-of-bounds in find_next_bit+0x38/0xb0
Fixes: 1b497e6493 ("PCI: dwc: Fix uninitialized variable in dw_handle_msi_irq()")
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
RISCV has csr_read()/write() macros in arch/riscv/include/asm/csr.h.
The same function naming is used in the PCI mobiveil driver thus
causing build error.
Rename csr_[read,write][l,] to mobiveil_csr_read()/write() to fix it.
drivers/pci/controller/pcie-mobiveil.c:238:69: error: macro "csr_read" passed 3 arguments, but takes just 1
static u32 csr_read(struct mobiveil_pcie *pcie, u32 off, size_t size)
drivers/pci/controller/pcie-mobiveil.c:253:80: error: macro "csr_write" passed 4 arguments, but takes just 2
static void csr_write(struct mobiveil_pcie *pcie, u32 val, u32 off, size_t size)
Fixes: bcbe0d9a8d ("PCI: mobiveil: Unify register accessors")
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Minghuan Lian <Minghuan.Lian@nxp.com>
Cc: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Cc: Andrew Murray <andrew.murray@arm.com>
Modify pci_epc_mem_alloc_addr() to cast the variable 'pageno'
from type 'int' to 'phys_addr_t' before shifting left. This
cast is needed to avoid treating bit 31 of 'pageno' as the
sign bit which would otherwise get sign-extended to produce
a negative value. When added to the base address of PCI memory
space, the negative value would produce an invalid physical
address which falls before the start of the PCI memory space.
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for the Amlogic G12A SoC using a separate shared PHY.
This adds support for fetching a PHY phandle and call the PHY init,
reset and power on/off calls instead of writing in the PHY register or
toggling the PHY reset line.
The MIPI clock and the PHY memory resource are only required for the
Amlogic AXG SoC PCIe PHY setup, thus these elements are ignored for
the Amlogic G12A having a separate shared PHY.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Fix the clock names used in the probe function according
to the bindings.
Fixes: 9c0ef6d34f ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Normally asserting reset signal on gpio would be achieved with:
gpiod_set_value_cansleep(reset_gpio, 1);
Meson PCI driver set reset value to '0' instead of '1' as it takes into
account the PERST# signal polarity. The polarity should be taken care
in the device tree instead.
This fixes the reset assertion meaning and moves out the polarity
configuration in DT (please note that there is no DT currently using
this driver).
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
advk_pcie_wait_pio() can be called while holding a spinlock (from
pci_bus_read_config_dword()), then depends on jiffies in order to
timeout while polling on PIO state registers. In the case the PIO
transaction failed, the timeout will never happen and will also cause
the cpu to stall.
This decrements a variable and wait instead of using jiffies.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
PCI_EXP_RTCTL is used to activate PME interrupt only, so writing into it
should not modify other interrupts' mask. The ISR mask polarity was also
inverted, when PCI_EXP_RTCTL_PMEIE is set PCIE_MSG_PM_PME_MASK mask bit
should actually be cleared.
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
When configuring pcie reset pin from gpio (e.g. initially set by
u-boot) to pcie function this pin goes low for a brief moment
asserting the PERST# signal. Thus connected device enters fundamental
reset process and link configuration can only begin after a minimal
100ms delay (see [1]).
Because the pin configuration comes from the "default" pinctrl it is
implicitly configured before the probe callback is called:
driver_probe_device()
really_probe()
...
pinctrl_bind_pins() /* Here pin goes from gpio to PCIE reset
function and PERST# is asserted */
...
drv->probe()
[1] "PCI Express Base Specification", REV. 4.0
PCI Express, February 19 2014, 6.6.1 Conventional Reset
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Aardvark's PCI_EXP_LNKSTA_LT flag in its link status register is not
implemented and does not reflect the actual link training state (the
flag is always set to 0). In order to support link re-training feature
this flag has to be emulated. The Link Training and Status State
Machine (LTSSM) flag in Aardvark LMI config register could be used as
a link training indicator. Indeed if the LTSSM is in L0 or upper state
then link training has completed (see [1]).
Unfortunately because after asking a link retraining it takes a while
for the LTSSM state to become less than 0x10 (due to L0s to recovery
state transition delays), LTSSM can still be in L0 while link training
has not finished yet. So this waits for link to be in recovery or lesser
state before returning after asking for a link retrain.
[1] "PCI Express Base Specification", REV. 4.0
PCI Express, February 19 2014, Table 4-14
Fixes: 8a3ebd8de3 ("PCI: aardvark: Implement emulated root PCI bridge config space")
Tested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
