We weren't unmapping DMA memory, which will break when gianfar gets used
on systems with more than 32-bits of memory. Also, it's just plain wrong.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The link may be up already via the chip's reset strapping, or though action
of U-Boot, or from the last time the interface was brought up. Resetting
the link causes it to go down for several seconds. This can significantly
increase the time from power-on to DHCP completion and a device being
accessible to the network.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The init_phy() function attaches to the PHY, then configures the
SerDes<->TBI link (in SGMII mode). The TBI is on the MDIO bus with the PHY
(sort of) and is accessed via the gianfar's MDIO registers, using the
functions gfar_local_mdio_read/write(), which don't do any locking.
The previously attached PHY will start a work-queue on a timer, and
probably an irq handler as well, which will talk to the PHY and thus use
the MDIO bus. This uses phy_read/write(), which have locking, but not
against the gfar_local_mdio versions.
The result is that PHY code will try to use the MDIO bus at the same time
as the SerDes setup code, corrupting the transfers.
Setting up the SerDes before attaching to the PHY will insure that there is
no race between the SerDes code and *our* PHY, but doesn't fix everything.
Typically the PHYs for all gianfar devices are on the same MDIO bus, which
is associated with the first gianfar device. This means that the first
gianfar's SerDes code could corrupt the MDIO transfers for a different
gianfar's PHY.
The lock used by phy_read/write() is contained in the mii_bus structure,
which is pointed to by the PHY. This is difficult to access from the
gianfar drivers, as there is no link between a gianfar device and the
mii_bus which shares the same MDIO registers. As far as the device layer
and drivers are concerned they are two unrelated devices (which happen to
share registers).
Generally all gianfar devices' PHYs will be on the bus associated with the
first gianfar. But this might not be the case, so simply locking the
gianfar's PHY's mii bus might not lock the mii bus that the SerDes setup
code is going to use.
We solve this by having the code that creates the gianfar platform device
look in the device tree for an mdio device that shares the gianfar's
registers. If one is found the ID of its platform device is saved in the
gianfar's platform data.
A new function in the gianfar mii code, gfar_get_miibus(), can use the bus
ID to search through the platform devices for a gianfar_mdio device with
the right ID. The platform device's driver data is the mii_bus structure,
which the SerDes setup code can use to lock the current bus.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
platform_get_irq*() returns on -ENXIO when the resource cannot be
found, but this remains unnoticed if stored in an unsigned.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The device's carrier status is controlled via the functions
netif_carrier_on() and netif_carrier_off(). These set or clear a bit
indicating the carrier (aka lower level link) is down, and if the state
changed, they fire off a routing netlink event.
Add a call to netif_carrier_off() before register_netdev() so that the
newly created device will be set to carrier down. Then when the carrier
comes up for the first time, a netlink event will be generated, as the
carrier changed from down to up. Otherwise the initial carrier up will
appear to be changing the status from up to up, and so no event is
generated since that's not a change.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gfar_halt() was factored out into halting and disabling by commit
d87eb12785, as the suspend() method
only wants to do the former. However, the call to gfar_halt_nodisable()
from gfar_halt() apparently got lost during the patch respin process.
This adds it back.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The commit that made the CONFIG_GFAR_NAPI code unconditional was
included at the same time as a new CONFIG_GFAR_NAPI user, resulting
in these bugus #ifdef's.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The loop that unmaps all of the TX Buffer Descriptors never actually
moves the txbd pointer, so we were just repeatedly unmapping the first one.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
During sparse cleanup, found a locking bug. Some of the sysfs functions were
acquiring a lock, and then returning in the event of an error. We rearrange
the code so that the lock is released in error conditions, too.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
TBIPA needs to be set to a value (on connected MDIO buses) that
doesn't conflict with PHYs on the bus. By hardcoding it to 0x1f,
we were preventing boards with PHYs at 0x1f from working properly.
Instead, scan the bus when it comes up, and find an address that
doesn't have a PHY on it. The TBI PHY configuration code then
trusts that the value in TBIPA is either safe, or doesn't matter
(ie - it's not an active bus with other PHYs).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
gianfar was unable to handle failed skb allocation for rx buffers, so
we were spinning until it succeeded. Actually, it was worse--we were
spinning for a long time, and then silently failing. Instead, we take
Stephen Hemminger's suggestion to try the allocation earlier, and drop the
packet if it failed.
We also make a couple of tweaks to how buffer descriptors are set up.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since 43cc71eed1, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable network
platform drivers, to re-enable auto loading.
NOTE: didn't change drivers/net/fs_enet/fs_enet-main.c "old binding" support.
That looks problematic in the first place (it even uses the ancient "struct
device_driver" binding scheme for platform_bus!) and I suspect it will vanish
soonish when arch/powerpc rules the world. Also, drivers/net/ne.c would have
needed more thought to sort out.
[akpm@linux-foundation.org: fix sgiseeq.c]
[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Dale Farnsworth <dale@farnsworth.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Poll the completed TX frames in gfar_poll(). This prevents the tx
completion interrupt from interfering with processing of received
frames.
We also disable hardware rx coalescing when NAPI is enabled.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- Fix Rx/Tx HW interrupt coalescing counter reset logic. Disabling
is required before resetting the counter.
- Update the Default both Rx and Tx coalescing timer
threshold. Formerly 4 is set which is equal to 1.5 frame at the line
rate of 1GbE interface, and it doesn't match to the coalescing frame
count which is set to 16. Threashold 21 is matched to frame count 16.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If the LAST bit is not set in the RxBD, it's possible we're processing
an incomplete frame, which is bad. While we're at it, add a constant
for the error bitmask, so the whole if-clause fits on one line,
and is more legible.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In gfar_change_mtu(), the frame size needs to be increased to account
for the extra 4 bytes VLAN adds to the ethernet header. However,
it was being increased by the length of the whole header (18 bytes),
which is wrong.
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change all dma op invocations in gianfar.c to actually pass in the
device pointer. Currently, the value is ignored, but it will be
used going forward as we implement archdata for 32-bit powerpc.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Eliminate an uninitialized variable warning. The code is correct, but
a pointer to the automatic variable 'addr' is passed to dma_alloc_coherent.
Since addr has never been initialized, and the compiler doesn't know
what dma_alloc_coherent will do with it, it complains.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Protect all new napi function calls with CONFIG_GFAR_NAPI. Otherwise
the driver will stop working when CONFIG_GFAR_NAPI disabled.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We now have struct net_device_stats embedded in struct net_device,
and the default ->get_stats() hook does the obvious thing for us.
Run through drivers/net/* and remove the driver-local storage of
statistics, and driver-local ->get_stats() hook where applicable.
This was just the low-hanging fruit in drivers/net; plenty more drivers
remain to be updated.
[ Resolved conflicts with napi_struct changes and fix sunqe build
regression... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.
In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.
The signature of the ->poll() call back goes from:
int foo_poll(struct net_device *dev, int *budget)
to
int foo_poll(struct napi_struct *napi, int budget)
The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract). The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.
The napi_struct is to be embedded in the device driver private data
structures.
Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler. Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.
With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.
Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.
[ Ported to current tree and all drivers converted. Integrated
Stephen's follow-on kerneldoc additions, and restored poll_list
handling to the old style to fix mutual exclusion issues. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSEC/eTSEC can detect the interface to the PHY automatically,
but it isn't able to detect whether the RGMII connection needs internal
delay. So we need to detect that change in the device tree, propagate
it to the platform data, and then check it if we're in RGMII. This fixes
a bug on the 8641D HPCN board where the Vitesse PHY doesn't use the delay
for RGMII.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add code for initialising and configuring TBI interface and
programming it for connecting to on-chip SERDES (Lynx PHY)
in case of SGMII mode selected through HRCW at reset.
also add defines for TBI register configuration. TBI
interface is programmed towards the SERDES.
refactored mdio read/write functions to differentiate
programming local interface MII regs (e.g., for TBI) from
always programming the mdio master (TSEC1, for programming
the PHYs).
Signed-off-by: Kapil Juneja <Kapil.Juneja@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In commit 4bedb45203 both the udp and tcp
cases where changed to use udp_hdr() instead of leaving the tcp case
alone and fixing with tcp_hdr().
This ended up causing random behavior with TCP connections because
of looking for tcp_hdr()->check in the wrong place.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Many drivers had code that did kill_vid, but they weren't doing vlan
filtering. With new API the stub is unneeded unless device sets
NETIF_F_HW_VLAN_FILTER.
Bad habit: I couldn't resist fixing a couple of nearby style things
in acenic, and forcedeth.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The hardware must not see that is given ownership of a buffer until it is
completely written, and when the driver receives ownership of a buffer,
it must ensure that any other reads to the buffer reflect its final
state. Thus, I/O barriers are added where required.
Without this patch, I have observed GCC reordering the setting of
bdp->length and bdp->status in gfar_new_skb. Hardware reordering
was also theoretically possible.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For the common sequence "skb->h.raw - skb->nh.raw", similar to skb->mac_len,
that is precalculated tho, don't think we need to bloat skb with one more
member, so just use this new helper, reducing the number of non-skbuff.h
references to the layer headers even more.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the quite common 'skb->nh.raw - skb->data' sequence.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One less thing for drivers writers to worry about.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I recognized a compile error in latest git:
/here/workdir/git/drivers/net/gianfar.c: In function `gfar_vlan_rx_kill_vid':
/here/workdir/git/drivers/net/gianfar.c:1135: error: structure has no member named `vgrp'
This error was introduced in commit:
commit 6d04e3b04b
...
[VLAN]: Avoid a 4-order allocation.
Signed-off-by: Jan Altenberg <jan@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits the vlan_group struct into a multi-allocated struct. On
x86_64, the size of the original struct is a little more than 32KB, causing
a 4-order allocation, which is prune to problems caused by buddy-system
external fragmentation conditions.
I couldn't just use vmalloc() because vfree() cannot be called in the
softirq context of the RCU callback.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was hardly necessary to repeat most of the code from gfar_error() in
gfar_interrupt(), especially having some inconsistencies between the two.
So, make the gfar_interrupt() just call gfar_error(), and not acknowledge
the interrupts itself as gfar_{receive/transmit/error}() do it anyway.
While at it, also clarify/cleanup debug messages in gfar_error()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
