These sub-commands are issued by another (FCoE) function requesting
an operation on a shared resource.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- TC35815_DMA_SYNC_ONDEMAND is always enabled.
- WORKAROUND_LOSTCAR is always enabled.
- WORKAROUND_100HALF_PROMISC is always enabled.
- GATHER_TXINT is always enabled.
- TC35815_USE_PACKEDBUFFER is always disabled.
- NO_CHECK_CARRIER is always disabled.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides basic hash rules programming via the ethtool
interface.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces multiple group support for etsec2.0
devices.
Multiple group support is provided by mapping the set of enabled
queues to different groups and then programming the per group
regsiters imask, ievent, rstat, tstat.
The queues corresponding to a group are indicated by programming
isrg (interrupt steering) registers.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for etsec2.0 regsiters
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds mdio support for etsec2.0 devices.
Modified the fsl_pq_mdio structure to include the new mdio
members.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces multiple Tx and Rx queues.
The incoming packets can be classified into different queues
based on filer rules (out of scope of this patch). The number
of queues enabled will be based on a DTS entries fsl,num_tx_queues
and fsl,num_rx_queues.
Although we are enabling multiple queues, the interrupt coalescing
is on per device level (etsec-1.7 doesn't support multiple rxics
and txics).
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the group structure. The elements of this
structure are the interrupt lines, their corresponding names,
the register memory map.
The elements for this group are factored out from the gfar_private
structure. The introduction of group structure will help in
providing support for newer versions of etsec.
Currently, the support is present only for single group and
single tx/rx queues.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces per tx and per rx queue structures.
Earlier the members of these structures were inside the
gfar_private structure.
Moving forward if we want to support multiple queues, we need
to refactor the gfar_private structure so that introduction of
multiple queues is easier.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.103.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to disable the TXC and RXC reference clocks if link
is not available.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an RXC auto power-down feature to the code that supports
the gphys.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5785 does not use the RXC reference clock. Turning it off is
desirable as it saves power.
By default, the 50610 enables the RXC reference clock and the 50610M
disables it. Presumably this is one of the reasons why the hardware
architect chose one over the other.
Adding a "rx reference clock disable" flag is not the ideal way to
describe the option, as it would force the MAC using a 50610M to set
the flag. Ideally we want the flags to represent opt-in behavior that
deviates from hardware defaults. Furthermore, the lack of a
"disable" flag implies that the requester wants the rx reference clock
enabled, which doesn't necessarily follow.
By presenting the option as a passive statement (rx reference clock
unused) rather than a command, I hope to convey an opt-in option to
disable the rx reference clock that falls back to hardware defaults if
not set. A secondary benefit of this is that it keeps the
intelligence about phy defaults in the broadcom module where it belongs
and allows the broadcom module more latitude should a bug arise.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Auto power-down (APD) support is a power-saving feature. It should be
selectively enabled since it might expose MAC bugs. This patch changes
the code to enable APD only if the PHY_BRCM_AUTO_PWRDWN_ENABLE flag is
set. The tg3 driver was changed to set this bit.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom 50610M parts changed the default definitions of the RGMII mode
shadow register. The 5785 needs the RGMII mode selection bits [4:3]
cleared.
The default value of the remaining bits in this register are zero.
Rather than unnecessarily burn an extra bit in the dev_flags member in
an attempt to enumerate all possible combinations, this patch take a
more course grained approach and labels the option as "clear all bits".
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves all the dev_flags enumerations outside the broadcom.c
file to include/linux/brcmphy.h. The existing flags were not used yet
and have been re-enumerated to avoid conflicts.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 50610M phy ID for 5785.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a 50610 or 50610M is paired against particular remote partners,
link is slow to come up. This patch works around the problem.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consolidates the code that requires the SMDSP clock to be
enabled into a single function that (hopefully) makes the dependency
obvious.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the loopback test timeout from 250 usec to 350 usec.
When the 5785 is paired against an AC131 phy, the older timeout is
just a little too close to the expected performance based on timings.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sets the port mode to MII when the link is down for the 5785.
Setting the port mode to MII instead of GMII saves power.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AC131 does not respect the power down bit (bit 11) of the MII
Control Register (reg 0x0). Instead, software is required to put the
phy into standby power down mode through the shadow register set. This
patch implements support for the AC131 standby power down mode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves 5785 performance by allowing the write DMA engine to
request larger DMA burst sizes than it otherwise would.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to check the status of pci_map_single() before
allowing rx buffers to be used. It also converts the pci_map_single()
call in tg3_run_loopback() to use skb_dma_map() instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prevents a PCIe tx glitch by allowing the transmitter to go
to a low power state.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames the PHY_ADDR preprocessor definition. The following
patch will identify a new member on the MDIO bus, so we want this
preprocessor definition to be a little more descriptive.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under certain power saving conditions, 57780 asic rev devices might
disappear from the system. The fix is to disallow the PCIe PLL from
powering down.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5906 has trouble with fragments that are less than 8 bytes in size.
This patch works around the problem by pivoting the 5906's transmit
routine to tg3_start_xmit_dma_bug() and introducing a new SHORT_DMA_BUG
flag that enables code to detect and react to the problematic condition.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a flag for each bug workaround in
tg3_start_xmit_dma_bug(). This is prep work for the following patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change name on vlan_rx_add, kill, register to match other driver API.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoids touching device refcount in datagram_send_ctl(), thanks to RCU
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoids touching device refcount in inet6_bind(), thanks to RCU
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using dev_get_by_index_rcu() in ip6_tnl_rcv_ctl() & ip6_tnl_xmit_ctl()
avoids touching device refcount.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- packet_sendmsg_spkt() can use dev_get_by_name_rcu() to avoid touching device refcount.
- packet_getname_spkt() & packet_getname() can use dev_get_by_index_rcu() to
avoid touching device refcount too.
tpacket_snd() & packet_snd() can not use RCU yet because they can sleep when
allocating skb.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_get_by_name_rcu() instead of dev_get_by_name(),
to avoid touching device refcount in hotpath.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All ioctls() implemented by dev_ifsioc_locked() :
SIOCGIFFLAGS, SIOCGIFMETRIC, SIOCGIFMTU, SIOCGIFHWADDR,
SIOCGIFSLAVE, SIOCGIFMAP, SIOCGIFINDEX & SIOCGIFTXQLEN
can use RCU lock instead of dev_base_lock rwlock
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can avoid touching device refcount in icmp_send(),
using dev_get_by_index_rcu()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_get_by_index_rcu() instead of __dev_get_by_index() and
dev_base_lock rwlock
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I tested the recent unregister many changes and got a weird,
nasty and seemingly unrelasted kernel oops. Changing
unregister_netdevice_queue to use list_move_tail fixes
the problem for me.
ip link add type veth
rmmod veth
ls /sys/class/net/
showed one of the veth devices still present.
A subsequent ip link oopsed the box.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some workloads hit dev_base_lock rwlock pretty hard.
We can use RCU lookups to avoid touching this rwlock
(and avoid touching netdevice refcount)
netdevices are already freed after a RCU grace period, so this patch
adds no penalty at device dismantle time.
However, it adds a synchronize_rcu() call in dev_change_name()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add API Add k8695_get_rx_enable_bit() for get Rx interrupt
enable/status bit.
2. add some comment or document about some functions and variables.
3. update driver version to "1.02"
4. add napi_enable() and napi_disable() in open/close file method.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move receive processing from event handler to a tasklet.
This should help prevent hangcheck timer from going off
when RDS is under heavy load.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was discovered by HP's Pradeep and fixed in OFED
1.3, but not fixed in later versions, since the fix's implementation
was not immediately applyable to the later code. This patch should
do the trick for 1.4+ codebases.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove explicit destruction of passive connection when destroying
active end of the connection. The passive end is also on the
device's connection list, and will thus be cleaned up properly.
Panic was caused by trying to clean it up twice.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"At rds_ib_recv_refill_one(), it first executes atomic_read(&rds_ib_allocation)
for if-condition checking,
and then executes atomic_inc(&rds_ib_allocation) if the condition was
not satisfied.
However, if any other code which updates rds_ib_allocation executes
between these two atomic operation executions,
it seems that it may result race condition. (especially when
rds_ib_allocation + 1 == rds_ib_sysctl_max_recv_allocation)"
This patch fixes this by using atomic_inc_unless to eliminate the
possibility of allocating more than rds_ib_sysctl_max_recv_allocation
and then decrementing the count if the allocation fails. It also
makes an identical change to the iwarp transport.
Reported-by: Shin Hong <hongshin@gmail.com>
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDS currently supports a GET_MR sockopt to establish a
memory region (MR) for a chunk of memory. However, the fastreg
method ties a MR to a particular destination. The GET_MR_FOR_DEST
sockopt allows the remote machine to be specified, and thus
support for fastreg (aka FRWRs).
Note that this patch does *not* do all of this - it simply
implements the new sockopt in terms of the old one, so applications
can begin to use the new sockopt in preparation for cutover to
FRWRs.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
