Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
[fixed direction enums and cyclic api based on changes
already merged]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Define a new api that could be used for doing fancy data transfers
like interleaved to contiguous copy and vice-versa.
Traditional SG_list based transfers tend to be very inefficient in
such cases as where the interleave and chunk are only a few bytes,
which call for a very condensed api to convey pattern of the transfer.
This api supports all 4 variants of scatter-gather and contiguous transfer.
Of course, neither can this api help transfers that don't lend to DMA by
nature, i.e, scattered tiny read/writes with no periodic pattern.
Also since now we support SLAVE channels that might not provide
device_prep_slave_sg callback but device_prep_interleaved_dma,
remove the BUG_ON check.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Acked-by: Barry Song <Baohua.Song@csr.com>
[renamed dmaxfer_template to dma_interleaved_template
did fixup after the enum dma_transfer_merge]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
On October 1 in 2011,
OKI SEMICONDUCTOR Co., Ltd. changed the company name in to LAPIS Semiconductor
Co., Ltd.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The individual SoC dependency in Kconfig hardly scales anymore.
Instead of having such a fine grained dependency just depend
on ARCH_MXC and risk that the uninformed user has to look in
the help text to figure out which driver is the correct one.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This patch adds to fix the build warning as following.
drivers/dma/pl330.c: In function 'pl330_probe':
drivers/dma/pl330.c:859: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add device tree probe support for atmel at_hdmac DMA driver.
Bindings are added to specify DMA controller configuration.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
We remove the use of platform data from DMA controller driver.
We now use of .id_table to distinguish between compatible
types. The two implementations allow to determine the
number of channels and the capabilities of the controller.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (63 commits)
dmaengine: mid_dma: mask_peripheral_interrupt only when dmac is idle
dmaengine/ep93xx_dma: add module.h include
pch_dma: Reduce wasting memory
pch_dma: Fix suspend issue
dma/timberdale: free_irq() on an error path
dma: shdma: transfer based runtime PM
dmaengine: shdma: protect against the IRQ handler
dmaengine i.MX DMA/SDMA: add missing include of linux/module.h
dmaengine: delete redundant chan_id and chancnt initialization in dma drivers
dmaengine/amba-pl08x: Check txd->llis_va before freeing dma_pool
dmaengine/amba-pl08x: Add support for sg len greater than one for slave transfers
serial: sh-sci: don't filter on DMA device, use only channel ID
ARM: SAMSUNG: Remove Samsung specific enum type for dma direction
ASoC: Samsung: Update DMA interface
spi/s3c64xx: Merge dma control code
spi/s3c64xx: Add support DMA engine API
ARM: SAMSUNG: Remove S3C-PL330-DMA driver
ARM: S5P64X0: Use generic DMA PL330 driver
ARM: S5PC100: Use generic DMA PL330 driver
ARM: S5PV210: Use generic DMA PL330 driver
...
Fix up fairly trivial conflicts in
- arch/arm/mach-exynos4/{Kconfig,clock.c}
- arch/arm/mach-s5p64x0/dma.c
To support multi-size buffers in the mx3_camera V4L2 driver we have to be
able to stop DMA on a channel without releasing descriptors and completely
halting the hardware. Use the DMA_PAUSE control to implement this mode.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix files that were implicitly using module.h but not
calling it out for inclusion directly. We'll break those
once we remove the implicit presence otherwise
[With input from Uwe Kleine-König <u.kleine-koenig@pengutronix.de>]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files aren't just exporting symbols -- they are also defining
a MODULE_LICENSE etc. so give them the full module.h file.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The mask_peripheral_interrupt is called when channel wants to mask the
interrupt. Move this to suspend as this masking affects other channels
as well. Not touching unmask here and unmask would still be done of
first channel use
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Due to module.h cleanup it is not anymore included implicitly. Drivers who
want to use it need to include it explicitly.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
nr_channels is defined in "struct pch_dma".
and struct pch_dma_chan is defined in "struct pch_dma".
So, "sizeof(struct pch_dma_chan) * nr_channels" is unnecessary.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
There was an error path that skipped the free_irq() step by mistake.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently the shdma dmaengine driver uses runtime PM to save power, when
no channel on the specific controller is requested by a user. This patch
switches the driver to count individual DMA transfers. That way the
controller can be powered down between transfers, even if some of its
channels are in use.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
The IRQ handler of the shdma driver accesses common hardware registers,
that are also accessed from other contexts. Therefore access to them
has to be performed with interrupts disabled, not only with disabled
bottom halves.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Add missing include of linux/module.h to fix build error.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_async_device_register will re-init chan_id and chancnt,
so whatever chan_id and chancnt are set in drivers, they will
be re-written by dma_async_device_register.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Viresh Kumar <viresh.kumar@st.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Piotr Ziecik <kosmo@semihalf.com>
Cc: Yong Wang <yong.y.wang@intel.com>
Cc: Jaswinder Singh <jassi.brar@samsung.com>
Cc: Pelagicore AB <info@pelagicore.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In pl08x_free_txd(), check if pool is allocated successfully before freeing it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Untill now, sg_len greater than one is not supported. This patch adds support to
do that.
Note: Still, if peripheral is flow controller, sg_len can't be greater that one.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds DMA_CYCLIC capability that is used for audio driver.
DMA driver activated with it reuses the dma requests that were submitted
through tx_submit().
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Original code carries out the start operation after flush operation.
But start operation is not required for DMA_TERMINATE_ALL command.
So, this patch removes the unnecessary start operation and only carries out
the flush operation for handling DMA_TERMINATE_ALL command.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[Fixed typos in changelog]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch updates following 3 items.
1. Removes unneccessary code.
2. Add AMBA, PL330 configuration
3. Change the meaning of 'peri_id' variable
from PL330 event number to specific dma id by user.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The bank_lock can be taken in atomic context (irq handling)
and therefore cannot be preempted on -rt - annotate it.
In mainline this change documents the low level nature of
the lock - otherwise there's no functional difference. Lockdep
and Sparse checking will work as usual.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: kernel@pengutronix.de
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Link: http://lkml.kernel.org/r/1311949627-13260-1-git-send-email-u.kleine-koenig@pengutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Before converting the dma channel to our private data structure, first
check that the channel is indeed one which our driver registered. We
do this by ensuring that the underlying device is bound to our driver.
This avoids potential oopses if we try to reference 'plchan->name'
against a foreign drivers dma channel.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Prepared descriptors that are not submitted will not be freed. Add
prepared descriptor to a list to be able to release them upon
dmaengine_terminate_all().
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The client list may exist in two lists at the same time. This makes free
fail since the same desc is freed multiple times. Remove desc from
client list when adding it to the pending queue. Move free of client owned
descriptors from free_dma() to terminate_all().
Unable to handle kernel paging request at virtual address 00100104
pgd = dea8c000
[00100104] *pgd=1ea62831, *pte=00000000, *ppte=00000000
Internal error: Oops: 817 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 Not tainted (3.1.0-rc3+ #58)
PC is at d40_free_chan_resources+0x64/0x330
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Prepared descriptors that are not submitted will not be freed. Add
prepared descriptor to a list to be able to release them upon
dmaengine_terminate_all().
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The client list may exist in two lists at the same time. This makes free
fail since the same desc is freed multiple times. Remove desc from
client list when adding it to the pending queue. Move free of client owned
descriptors from free_dma() to terminate_all().
Unable to handle kernel paging request at virtual address 00100104
pgd = dea8c000
[00100104] *pgd=1ea62831, *pte=00000000, *ppte=00000000
Internal error: Oops: 817 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 Not tainted (3.1.0-rc3+ #58)
PC is at d40_free_chan_resources+0x64/0x330
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The firmware blob may not be available when the driver
probes. Instead of blocking the whole kernel use
request_firmware_nowait() and continue without firmware.
The ROM scripts can already be used then if available.
For the devicetree case the ROM scripts are not available,
still the probe function should not block. The driver
will be unusable in this case, but we have no way of
detecting this properly. The configuration of the dma
channels will fail, so nothing bad should happen.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
If we do not have a firmare script for a given transfer,
the setup of this channel must fail. For this the script
addresses have to be < 0 initially, not 0.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
channel0 of the sdma engine is the configuration channel. It
is a shared resource and thus must be protected by a mutex.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Making dmatest threads freezable allows its use for system PM testing.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
At least, on SPEAr platforms there is one peripheral, JPEG, which can be flow
controller for DMA transfer. Currently DMA controller driver didn't support
peripheral flow controller configurations.
This patch adds device_fc field in struct pl08x_channel_data, which will be used
only for slave transfers and is not used in case of mem2mem transfers.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When we have DMA transfers between peripheral and memory, then we shouldn't
reduce width of peripheral at all, as that may be a strict requirement. But we
can always reduce width of memory access, with some compromise in performance.
Thus, we must select peripheral as master and not memory.
Also this rearranges code to make it shorter.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently lli_len is aligned to min of two widths, which looks to be incorrect.
Instead it should be aligned to max of both widths.
Lets say, total_size = 441 bytes
MIN: lets check if min() suits or not:
CASE 1: srcwidth = 1, dstwidth = 4
min(src, dst) = 1
i.e. We program transfer size in control reg to 441.
Now, till 440 bytes everything is fine, but on the last byte DMAC can't transfer
1 byte to dst, as its width is 4.
CASE 2: srcwidth = 4, dstwidth = 1
min(src, dst) = 1
i.e. we program transfer size in control reg to 110 (data transferred = 110 * srcwidth).
So, here too 1 byte is left, but on the source side.
MAX: Lets check if max() suits or not:
CASE 3: srcwidth = 1, dstwidth = 4
max(src, dst) = 4
Aligned size is 440
i.e. We program transfer size in control reg to 440.
Now, all 440 bytes will be transferred without any issues.
CASE 4: srcwidth = 4, dstwidth = 1
max(src, dst) = 4
Aligned size is 440
i.e. We program transfer size in control reg to 110 (data transferred = 110 * srcwidth).
Now, also all 440 bytes will be transferred without any issues.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Code for creating single byte llis is present at several places. Create a
routine to avoid code redundancy.
Also, we don't need one lli per single byte transfer, we can have single lli to
do all single byte transfer.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
max_bytes_per_lli = bd.srcbus.buswidth * PL080_CONTROL_TRANSFER_SIZE_MASK;
This is confirmed by ARM support guys.
Below is summary of mail exchange with them:
[Viresh] What is the total data to be transferred in case source and destination
bus widths are different. Suppose, source bus width is 2 bytes and destination
is 4 bytes. Now in order to transfer 80 bytes, what should be value of
TransferSize field in control reg: 40? or 20?.
[David from ARM] The value that is programmed into the TransferSize field should
be the number of <SourceWidth> transfers needed to achieve the required data
transfer.
So, to transfer 80 bytes, with a Source Width of 2, the TransferSize field =
should be programmed with:
Total transfer size
------------------- = 40
<source width>
[Viresh] Will this change if source is 4 bytes and dest is 2?
[David] Yes - the calculation then becomes:
Total transfer size
------------------- =20
<source width>
Also, max_bytes_per_lli must be calculated after fixing src and dest widths not
before that. So move this code to the correct place.
This patch also removes max_bytes_per_lli from earlier print message, as till
that point max_bytes_per_lli is unknown.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pl080 Manual says: "Bursts do not cross the 1KB address boundary"
We can program the controller to cross 1 KB boundary on a burst and controller
can take care of this boundary condition by itself.
Following is the discussion with ARM Technical Support Guys (David):
[Viresh] Manual says: "Bursts do not cross the 1KB address boundary"
What does that actually mean? As, Maximum size transferable with a single LLI is
4095 * 4 =16380 ~ 16KB. So, if we don't have src/dest address aligned to burst
size, we can't use this big of an LLI.
[David] There is a difference between bursts describing the total data
transferred by the DMA controller and AHB bursts. Bursts described by the
programmable parameters in the PL080 have no direct connection with the bursts
that are seen on the AHB bus.
The statement that "Bursts do not cross the 1KB address boundary" in the TRM is
referring to AHB bursts, where this limitation is a requirement of the AHB spec.
You can still issue bursts within the PL080 that are in excess of 1KB. The
PL080 will make sure that its bursts are broken down into legal AHB bursts which
will be formatted to ensure that no AHB burst crosses a 1KB boundary.
Based on above discussion, this patch removes all code related to 1 KB boundary
as we are not required to handle this in driver.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently, if error interrupt occurs, nothing is done in interrupt handler (just
clearing the interrupts). We must somehow indicate this to the user that DMA is
over, due to ERR interrupt or TC interrupt.
So, this patch just schedules existing tasklet, with a print showing error
interrupt has occurred on which channels.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We have just executed following in pl08x_get_phy_channel():
ch->signal = -1;
We don't have to compare "ch->signal < 0", as this will always be true.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Simply writing 1 on bit 0 is sufficient instead of reading and clearing bits.
Also as per manual, for bit 3-31 of DMACConfiguration register:
"read undefined, write as 0"
So, we must not rely on values read from this registers bit 3-31.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Insert notifiers for the runtime PM API. With this the runtime PM layer kicks in
to action where used.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
For 8 memory and 16 slave channels 35 boot print lines are printed. And that is
too much. Most of this would be more useful for debugging. So moving few of them
to dev_dbg instead of dev_info. Now only 3 prints will be printed.
This also rearrange one of the debug message to fit into two lines.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Similar comment is present over routine also pl08x_choose_master_bus(). Keeping
one of them. Also rewrite that comment to convey message clearly.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
As mentioned in Documentation/CodingStyle,
The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
The alternative form where struct name is spelled out hurts readability and
introduces an opportunity for a bug when the pointer variable type is changed
but the corresponding sizeof that is passed to a memory allocator is not.
This patch replaces (struct xyz) with *ptr at several occurrences in driver.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Header files included in driver are not present in alphabetical order. Rearrange
them in alphabetical order.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There were few formatting related issues in code. This patch fixes them.
Fixes include:
- Remove extra blank lines
- align code to 80 cols
- combine several lines to one line
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In this driver, we can trigger cyclic transfer on peripherals-DMA interfaces.
It is dependent on driver implementation but cannot depend on a platform
property: we remove the dma_has_cap(DMA_CYCLIC, ) test which has no meaning.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Cyclic property and paused state are encoded as bits in the channel status
bitfield. Tests of those bits are wrapped in convenient helper functions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Save/restore dma controller state across a suspend-resume sequence.
The prepare() function will wait for the non-cyclic channels to become idle.
It also deals with cyclic operations with the start at next period while
resuming.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dmaengine routines can be called from interrupt context and with
interrupts disabled. Whereas spin_unlock_bh can't be called from
such contexts. So this patch converts all spin_lock* routines
to irqsave variants.
Also, spin_lock() used in tasklet is converted to irqsave variants,
as tasklet can be interrupted, and dma requests from such interruptions
may also call spin_lock.
Idea from dw_dmac patch by Viresh Kumar.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
After calling mxs_dma_disable_chan() for a channel, that channel
becomes unusable because some controller registers can only be written
when the clock is enabled via CLKGATE.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: drop experimental status for ARM_PATCH_PHYS_VIRT
ARM: 7008/1: alignment: Make SIGBUS sent to userspace POSIXly correct
ARM: 7007/1: alignment: Prevent ignoring of faults with ARMv6 unaligned access model
ARM: 7010/1: mm: fix invalid loop for poison_init_mem
ARM: 7005/1: freshen up mm/proc-arm946.S
dmaengine: PL08x: Fix trivial build error
ARM: Fix build error for SMP=n builds
Something changed during the 3.1 merge window in the include files
which now causes the pl08x DMA engine driver to fail to build. Fix
this by adding the now necessary dma-mapping.h include:
drivers/dma/amba-pl08x.c: In function ■pl08x_unmap_buffers■:
drivers/dma/amba-pl08x.c:1524: error: implicit declaration of function ■dma_unmap_single■
drivers/dma/amba-pl08x.c:1527: error: implicit declaration of function ■dma_unmap_page■
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In case, some error occurs while doing memcpy transfers, we must terminate all
transfers physically too. This is achieved by calling device_control() routine
with TERMINATE_ALL as parameter.
This is also required to be done in case module is removed while we are in
middle of some transfers.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: use DEFINE_IDR for static initialization
ioat: fix xor_idx_to_desc
Avoid section type conflict in dma/ioat/dma_v3.c
ioat: Adding PCI IDs for IOAT devices on SandyBridge platforms
We could use DEFINE_IDR for statically allocated idr
that allow us to save a few lines of code.
And also remove unneeded mutex_init() for dma_list_mutex, as
dma_list_mutex is initialized automatically by DEFINE_MUTEX().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For versions of the device that implement operation-types 0x87, 0x88
(IOAT_OP_XOR, IOAT_OP_XOR_VAL) this map determines whether a given
source is located in the base or extended descriptor. Source addresses
6 through 8 require an extended descriptor, hence 0xe0, not 0xd0. No
shipping hardware currently implements these operation types.
Reported-by: Evgueni Smogailov <evgueni.smogailov@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
It does not need to allocate space and copy fw_name in function
sdma_get_firmware().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
It might be not good to use software defined version to identify sdma
device type, when hardware does not define such version. Instead,
soc name is stable enough to define the device type.
The patch uses platform_device_id rather than version number passed
by platform data to identify sdma device type/version.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Vinod Koul <vinod.koul@intel.com>
pl08x_width function does not handle rest of enums for DMA_SLAVE_BUSWIDTH_xxxx
which causes gcc to emit below warining
drivers/dma/amba-pl08x.c: In function 'pl08x_width':
drivers/dma/amba-pl08x.c:1119: warning: enumeration value
'DMA_SLAVE_BUSWIDTH_UNDEFINED' not handled in switch
drivers/dma/amba-pl08x.c:1119: warning: enumeration value
'DMA_SLAVE_BUSWIDTH_8_BYTES' not handled in switch
this patch adds a default case which returns error
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now that we have separate cctl values for M>P and P>M transfers, we can
avoid calculating the cctl value each time we prepare a transaction.
Move the bus selection and increment setting to the slave configuration
and initialization functions.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Store the source/destination cctl values into the channel structure.
This moves us towards being able to avoid a configuration call each
time we use the channel.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Store the source/destination slave address separately into the channel
structure. This moves us towards being able to avoid a configuration
call each time we use the channel.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Clean up debugging when setting up the LLI list. This reduces the
amount of output while preserving the information, and makes it easier
to read.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Avoid re-selecting the LLI bus each time we create an LLI. Move it out
of the LLI setup loops.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
PL08X_WQ_PERIODMIN and PL08X_MAX_ALLOCS are not used, remove them.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We met some channels in abnormal state after disable.
Reset it to get a clean state.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Call pci_set_drvdata() once in intel_mid_dma_probe() is enough.
Remove redundant pci_set_drvdata() calls in dma_suspend() and dma_resume().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pl330 needs platform data for describing peripheral connections, but
some platforms may only support memory to memory dma channels. In this
case, we can probe for how many channels there are and don't need the
platform data.
As memcpy requests don't need channel private data to hold peripheral
info, allow private data to be NULL in this case.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Vinod Koul <vkoul@infradead.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
* 'next/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (35 commits)
ARM: msm: platsmp: determine number of CPU cores at boot time
ARM: Tegra: Seaboard: Fix I2C bus numbering for ADT7461
ARM: Tegra: Trimslice: Tri-state DAP3 pinmux
ARM: orion5x: fixup 5181 MPP mask check
ARM: mxs-dma: include <linux/dmaengine.h>
ARM: i.MX53: consistently use MX53_UART_PAD_CTRL for uart txd/rxd/rts/cts
ARM: i.MX53: UARTn_CTS pin should not change RTS input select
ARM: i.MX53: UARTn_TXD pin should not change RXD input select
ARM: mx25: Fix typo on CAN1_RX pad setting
iomux-mx53: add missing 'IOMUX_CONFIG_SION' for some I2C pad definitions
ARM: NUC93X: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: LPC32XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: CNS3XXX: add UL suffix to VMALLOC_END to ensure it is properly typed
ARM: i.MX53: Fix IOMUX type o's
ARM i.MX dma: Fix burstsize settings
mach-mx5: fix the I2C clock parents
ARM: mxs/tx28: according to the TX28's datasheet D4-D7 are not used for MMC0
ARM i.MX23/28: platform-mxsfb: Add missing include of linux/dma-mapping.h
ARM: mx53: Fix some interrupts marked as reserved.
MXC: iomux-v3: correct NO_PAD_CTRL definition
...
Fix up trivial conflict in arch/arm/mach-imx/mach-mx31_3ds.c
Currently, Mode-Control register is accessed by read-modify-write.
According to DMA hardware specifications datasheet, prohibits this method.
Because this register resets to 0 by DMA HW after DMA transfer completes.
Thus, current read-modify-write processing can cause unexpected behavior.
The datasheet says in case of writing Mode-Control register, set the value for only target channel, the others must set '11b'.
e.g. Set DMA0=01b DMA11=10b
CTL0=33333331h
CTL2=00002333h
NOTE:
CTL0 includes DMA0~7 Mode-Control register.
CTL2 includes DMA8~11 Mode-Control register.
This patch modifies the issue.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
