Combine two end-cases in the same if statement with a single return value.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mlx4_en_reset_config, there was a redundant warn print that was left
from previous versions of this function. No warn is needed anymore.
This warn can be confusing when RX-FCS is changed:
Turn OFF RX-FCS:
mlx4_en: eth1: Changing device configuration rx filter(0) rx vlan(1)
Turn ON RX-FCS:
mlx4_en: eth1: Changing device configuration rx filter(0) rx vlan(1)
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add physical RX/TX packets/bytes counters into ethtool output to monitor
all traffic that was received and transmitted on the port. These
counters are available only for none Virtual Function.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to mirror-to-gretap, this enables mirroring to IPv6 gretap
netdevice.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a user requests mirror from a mlxsw physical port (possibly based
on an ACL match) to a gretap netdevice, the driver needs to resolve the
request to a particular physical port that the mirrored packets will
egress through, and a suite of configuration keys (importantly, IP and
MAC addresses). That means calling into routing and neighbor kernel code
to simulate the decisions made by the system for packets passing through
a gretap netdevice.
Add a new instance of mlxsw_sp_span_entry_ops to support this.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for whether a mirror port (which is a mlxsw front panel port)
belongs to the same mlxsw instance as the mirrored port, is currently
only done in spectrum_acl, even though it's applicable for the matchall
case as well. Thus move it to mlxsw_sp_span_entry_create().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some netdevices, for which mlxsw offloads mirroring, may have a
complex relationship between the declared intent and low-level
device configuration.
Trying to accurately track which changes might influence offloading
decisions is finicky and error-prone. Instead, this patch introduces a
function mlxsw_sp_span_entry_respin, which re-queries the configuration
anew and, if different, removes the existing offloads and installs new
ones.
Call this function strategically at event handlers that might influence
the mirroring configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support mirroring to different device types, the functions that
partake in configuring the port analyzer need to be extended to admit
non-trivial SPAN types.
Create a structure where all details of SPAN configuration are kept,
struct mlxsw_sp_span_parms. Also create struct mlxsw_sp_span_entry_ops
to keep per-SPAN-type operations.
Instantiate the latter once for MLXSW_REG_MPAT_SPAN_TYPE_LOCAL_ETH, and
once for a suite of NOP callbacks used for invalidated SPAN entry. Put
the formet as a sole member of a new array mlxsw_sp_span_entry_types,
where all known SPAN types are kept. Introduce a new function,
mlxsw_sp_span_entry_ops(), to look up the right ops suite given a
netdevice.
Change mlxsw_sp_span_mirror_add() to use both parms and ops structures.
Change mlxsw_sp_span_entry_get() and mlxsw_sp_span_entry_create() to
take these as arguments. Modify mlxsw_sp_span_entry_configure() and
mlxsw_sp_span_entry_deconfigure() to dispatch to ops.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the only mirror action supported by mlxsw is mirror to another
mlxsw physical port. Correspondingly, span_entry, which tracks each
mlxsw mirror in the system, currently holds a u8 number of the
destination port.
To extend this system to mirror to gretap and ip6gretap netdevices, have
struct mlxsw_sp_span_entry actually hold the destination netdevice
itself.
This change then trickles down in obvious manner to SPAN module API and
mirror-related interfaces in struct mlxsw_afa_ops.
To prevent use of invalid pointer, NETDEV_UNREGISTER needs to be hooked
and the corresponding SPAN entry invalidated.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuring the hardware for encapsulated SPAN involves more code than
the simple mirroring case. Extract the related code to a separate
function to separate it from the rest of SPAN entry creation. Extract
deconfigure as well for symmetry, even though disablement is the same
regardless of SPAN type.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is known statically ahead of time which SPAN entry will have which
ID. Just initialize it eagerly in mlxsw_sp_span_init(), don't wait until
the entry is actually created. This simplifies some code in
mlxsw_sp_span_entry_create()
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of removing span_entry by the port number, allow removing by
SPAN id. That simplifies some code right here, and for mirroring to soft
netdevices, avoids problems with netdevice pointer invalidation and
reuse.
Rename mlxsw_sp_span_entry_find() to mlxsw_sp_span_entry_find_by_port()
and keep it--follow-up patches will make use of it.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support encapsulated SPAN, extend mlxsw_reg_mpat_pack() with a field
to set the SPAN type.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPAT Register is used to query and configure the Switch Port Analyzer
Table. To configure Port Analyzer to encapsulate mirrored packets,
additional fields need to be specified for the MPAT register.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support mirroring to ip6gretap, the SPAN module needs to be able to
decode IPv6 addresses specified at that tunnel.
Extend mlxsw_sp_ipip_netdev_saddr() and mlxsw_sp_ipip_netdev_daddr() to
support IPv6 addresses. To that end, add and publish a support function
mlxsw_sp_ipip_netdev_parms6().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the logic for determining whether a given IPv4/IPv6 address is
all-zeroes from mlxsw_sp_ipip_tunnel_complete to a separate function.
Make that function public within the module.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a device reset fails for some reason, TX and RX queue resources
could be released. If a user attempts to open the device in this scenario,
it may result in a kernel panic as the driver tries to access this
memory. To fix this, include a check before device login that TX/RX
queues are still there before enabling the device. In addition, return a
value that can be checked in case of any errors to avoid waiting for a
completion that will never come.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not necessary to report each time a queue is stopped and restarted
as an informational message. Change that to be a debug message so that
it can be observed if needed but not printed by default.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver releases resources after a failed reset or some other
error, the driver might attempt to clean up and free memory that
isn't there anymore. Include some additional checks that RX/TX queues
along with their associated structures are still there before cleaning.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, buffers holding individual queue statistics are allocated
when the device is opened. If an ibmvnic interface is hotplugged or
initialized but never opened, an attempt to get statistics with
ethtool will result in a kernel panic.
Since the driver allocates a constant number, the maximum supported
queues, of buffers, these can be allocated during device probe and
freed when the device is hot-unplugged or the module is removed.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sorry, the previous change introduced a race condition between
transmit completion processing and tracking TX descriptors. If a
completion is received before the number of descriptors is logged,
the number of descriptors will be add but not removed. After enough
times, this could halt the transmit queue forever.
Log the number of descriptors used by a transmit before sending.
I stress tested the fix on two different systems running over the
weekend without any issues.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make dwmac4_release_tx_desc() clear all descriptor fields, not just
TDES2 and TDES3.
I'm suspecting that TDES0 and TDES1 wasn't cleared because the DMA
engine uses them to store the tx hardware timestamp (if PTP is enabled).
However, stmmac_tx_clean() calls stmmac_get_tx_hwtstamp(), which reads
and saves the timestamp, before it calls release_tx_desc(), so this
is not an issue.
stmmac_xmit() and stmmac_tso_xmit() both always overwrite TDES0,
however, stmmac_tso_xmit() sometimes sets TDES1, and since neither
stmmac_xmit() nor stmmac_tso_xmit() explicitly clears TDES1, both
functions might reuse a DMA descriptor with old TDES1 data.
I haven't observed any misbehavior even though TDES1 sometimes
point to an old skb, however, explicitly clearing both TDES0 and TDES1
in dwmac4_release_tx_desc() minimizes the chances of undefined behavior.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Documentation/memory-barriers.txt, we need to use a
dma_rmb() after reading the status/own bit, to ensure that all
descriptor fields are read after reading the own bit.
This way, we ensure that the DMA engine is done with the DMA
descriptor before we read the other descriptor fields, e.g. reading
the tx hardware timestamp (if PTP is enabled).
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last memory barrier in stmmac_xmit()/stmmac_tso_xmit() is placed
between a coherent memory write and a MMIO write:
The own bit is written in First Desc (TSO: MSS desc or First Desc).
<barrier>
The DMA engine is started by a write to the tx desc tail pointer/
enable dma transmission register, i.e. a MMIO write.
This barrier cannot be a simple dma_wmb(), since a dma_wmb() is only
used to guarantee the ordering, with respect to other writes,
to cache coherent DMA memory.
To guarantee that the cache coherent memory writes have completed
before we attempt to write to the cache incoherent MMIO region,
we need to use the more heavyweight barrier wmb().
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A dma_wmb() is used to guarantee the ordering, with respect to
other writes, to cache coherent DMA memory.
There is a dma_wmb() in prepare_tx_desc()/prepare_tso_tx_desc() which
ensures that TDES0/1/2 is written before TDES3 (which contains the own
bit), for First Desc.
However, in the rare case that MSS changes, there will be a MSS
context descriptor in front of the regular DMA descriptors:
<MSS desc> <- DMA Next Descriptor
<First Desc>
<desc n>
<Last Desc>
Thus, for this special case, we need a dma_wmb()
after prepare_tso_tx_desc()/before writing the own bit to the MSS desc,
so that we flush the write to TDES3 for First Desc,
in order to ensure that the MSS descriptor is the last descriptor to
set the own bit.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-02-26
This series contains updates to i40e and i40evf only.
Mariusz adds a new ethtool private flag for forcing true link state with
the requested changes from Jakub Kicinski.
Paweł fixes an issue where we were double locking the same resource
which would generate a kernel panic after bringing an interface up for
i40evf.
Alan modifies both drivers to use software values to determine if there
are packets stalled on the ring with the added benefit of being less CPU
intensive since we do not need to reach into the hardware to get the
values.
Colin Ian King provides a few fixes detected by Coverity, first was to
pass a struct by reference versus by value to be more efficient. Then
verify the VSI pointer is not NULL before trying to dereference it.
Cleaned up redundant checks that always return true.
Dan Carpenter fixes over indented lines of code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves few aspects of interrupt handling:
- update to current interrupt allocation API
(use pci_alloc_irq_vectors() instead of deprecated pci_enable_msi())
- this implicitly will allocate a MSI-X interrupt if available
- get rid of flag RTL_FEATURE_MSI
- remove some dead code, intentionally disabling (unreliable) MSI
being partially available on old PCI chips.
The patch works fine on a RTL8168evl (chip version 34) and on a
RTL8169SB (chip version 04).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds allmulticast option for memac, dtsec
and 10GEC controllers.
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code and avoid some Rx errors not being
accounted.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An issue in the code mapping the skb fragments into
scatter-gather frames was evidentiated by netperf
TCP_SENDFILE tests. The size was set wrong for all
fragments but the first, affecting the transmission
of any skb with more than one fragment.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Schmidt says:
====================
pull-request: ieee802154-next 2018-02-26
An update from ieee802154 for *net-next*
Alexander corrected a setting which got lost during some 6lowpan rework
a while back and Xue Liu provided us with a new driver for the MCR20A
transceiver.
If there are any issues let me know. If not, please pull.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations unregister ipvlan net hooks.
nf_unregister_net_hooks() removes hooks one-by-one,
and then frees the memory via rcu. This looks similar
to that happens, when a new hooks is added: allocation
of bigger memory region, copy of old content, and rcu
freeing the old memory. So, all of net code should be
well with this behavior. Also at the time of hook
unregistering, there are no packets, and foreign net
pernet_operations are not interested in others hooks.
So, we mark them as async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations are similar to bond_net_ops. Exit method
unregisters all net vlanx devices, and it looks like another
pernet_operations are not interested in foreign net vlanx list.
So, it's possible to mark them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations are similar to bond_net_ops. Exit method
unregisters all net ppp devices, and it looks like another
pernet_operations are not interested in foreign net ppp list.
So, it's possible to mark them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations are similar to bond_net_ops. Exit method
unregisters all net gtp devices, and it looks like another
pernet_operations are not interested in foreign net gtp list.
So, it's possible to mark them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations are similar to bond_net_ops. Exit method
unregisters all net geneve devices, and it looks like another
pernet_operations are not interested in foreign net geneve list.
So, it's possible to mark them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations populate/depopulate /proc and /sys
entries. Exit method unregisters all net bond devices, and
it seems another pernet_operations are not interested in
foreign net bond list. So, it's possible to mark them async.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations make pretty simple actions
like variable initialization on init, debug checks
on exit, and so on, and they obviously are able
to be executed in parallel with any others:
vrf_net_ops
lockd_net_ops
grace_net_ops
xfrm6_tunnel_net_ops
kcm_net_ops
tcf_net_ops
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These pernet_operations just create and destroy /proc entries,
and they can safely marked as async:
pppoe_net_ops
vlan_net_ops
canbcm_pernet_ops
kcm_net_ops
pfkey_net_ops
pppol2tp_net_ops
phonet_net_ops
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer depend on IPV6, but that now causes a link error with
CONFIG_IPV6=m and CONFIG_IPVLAN=y:
drivers/net/ipvlan/ipvlan_core.o: In function `ipvlan_queue_xmit':
ipvlan_core.c:(.text+0x1440): undefined reference to `ip6_route_output_flags'
drivers/net/ipvlan/ipvlan_core.o: In function `ipvlan_l3_rcv':
ipvlan_core.c:(.text+0x1818): undefined reference to `ip6_route_input_lookup'
This adds back the dependency on IPV6, with the option of building without
IPV6, but forcing IPVLAN to be a module when IPV6 is a module.
Fixes: 94333fac44 ("ipvlan: drop ipv6 dependency")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2018-02-26
This series contains updates to ixgbe and ixgbevf only.
Colin Ian King cleans up redundant variable assignments.
Tonghao Zhang updates ixgbe to avoid writing to the hardware when the
redirection table has not changed.
Jake fixes the driver logic for checking and clearing receive timestamp
hangs so that when the PTP_RX_TIMESTAMP_IN_REGISTER flag is set, we no
longer need to check for receive timestamp hangs, which in turn will
stop the spurious log messages.
Emil updates ixgbevf with several features and improvements done in
other drivers, starting with the handling of page addresses so that we
always refer to them using a void pointer. Added a 'legacy-rx' flag to
allow switching between the old and new receive code paths. Added
support for using 3K buggers in order 1 page. Updated the driver to
ensure that calls to ixgbevf_open() are rtnl lock protected and improved
the error handling when setting up multiple queues. Added support for
providing a buffer with head room and tail room to allow for shared
info, NET_SKB_PAD, and NET_IP_ALIGN, so that we can start using
build_skb to build frames instead of using memcpy() the headers.
Updated the logic of handling rings closer to ixgbe. Consolidated the
receive paths to reduce duplication when we expand them in the future.
Added build_skb() support to ixgbevf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These two lines are indented too far.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The checks to see if key->dst.s6_addr and key->src.s6_addr are null
pointers are redundant because these are constant size arrays and
so the checks always return true. Fix this by removing the redundant
checks. Also replace filter->f with vf, allowing wide lines to be
condensed and to rejoin some split wide lines.
Detected by CoverityScan, CID#1465279 ("Array compared to 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Function i40e_find_vsi_from_id can potentially return null, hence
VSI may be null, so defensively check it is non-null before
dereferencing it to check the seid.
Fixes: e284fc2804 ("i40e: Add and delete cloud filter")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Passing struct virtchnl_filter f by value requires a 272 byte copy
on x86_64, so instead pass it by reference is much more efficient. Also
adjust some lines that are over 80 chars.
Detected by CoverityScan, CID#1465285 ("Big parameter passed by value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40e_detect_recover_hung function uses the i40e_get_tx_pending
function to determine if there are packets stalled on the ring.
i40e_get_tx_pending calculates the pending packets using the head
writeback value and HW tail. If the queue is stopped and we lose the
interrupt to update our next_to_clean then we a) won't get another
interrupt to clean because queue is stopped b) we won't catch the
problem with i40e_detect_recover_hung because the HW values look like
there's no packets waiting to be transmitted. Using the SW values we
can catch the issue because next_to_clean will be out of sync with head
writeback.
This has the added benefit being less CPU intensive because we don't
need to reach into the hardware to get the values.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removes the locking of adapter->mac_vlan_list_lock resource in
i40evf_add_filter(). The locking part is moved above i40evf_add_filter().
i40evf_add_filter(), called by i40evf_addr_sync(), was trying to lock the
resource again and double locking generated a kernel panic after bringing
an interface up.
Fixes: 8946b56354 ("i40evf: use __dev_[um]c_sync routines in
.set_rx_mode")
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces new ethtool private flag used for
forcing true link state. Function i40e_force_link_state that implements
this functionality was added, it sets phy_type = 0 in order to
work-around firmware's LESM. False positive error messages were
suppressed.
The ndo_open() should not succeed if there were issues with forcing link
state to be UP.
Added I40E_PHY_TYPES_BITMASK define with all phy types OR-ed together in
one bitmask. Added after phy type definition, so it will be hard to
forget to include new phy types to the bitmask.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eliminate duplicated debug code by moving it into the core driver.
Don't log the only valid silicon revision number (it's in the source).
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Chris Zankel <chris@zankel.net>
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
