Enable pinctrl drivers for 64-bit Amlogic SoCs to be built as modules.
The default is still built-in, this only adds the option of building
as modules.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201026183025.31768-1-khilman@baylibre.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It has never been used.
Fixes the following W=1 kernel build warning(s):
drivers/pinctrl/meson/pinctrl-meson-a1.c:749:27: warning: ‘i2c_slave_groups’ defined but not used [-Wunused-const-variable=]
749 | static const char const i2c_slave_groups[] = {
| ^~~~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Qianggui Song <qianggui.song@amlogic.com>
Cc: linux-amlogic@lists.infradead.org
Link: https://lore.kernel.org/r/20200713144930.1034632-24-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a GPIO bank has greater than 16 pins, PAD_DS_REG is split into two
or more registers. However, when register and bit were calculated, the
first register defined in the bank was used, and the bit was calculated
based on the first pin. This causes problems in setting the driving
strength.
The following method was used to solve this problem:
A bit is calculated first using predefined strides. Then, If the bit is
32 or more, the register is changed by the quotient of the bit divided
by 32. And the bit is set to the remainder.
Signed-off-by: Hyeonki Hong <hhk7734@gmail.com>
Link: https://lore.kernel.org/r/20200618025916.GA19368@home-desktop
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use gpiochip_generic_config for the gpio_chip's set_config callback so
GPIO flags like GPIO_PULL_UP or GPIO_PULL_DOWN can be used in the board
.dts descriptions.
This is required for some Meson8m2 boards where GPIO_BSD_EN provides the
"MUTE" signal and requires enabling the internal pull-up resistor.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20200417183349.1283092-3-martin.blumenstingl@googlemail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement the get_direction callback so we read the direction from the
actual GPIO controller register. This is recommended by the gpio_chip
kernel doc.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20200417183349.1283092-2-martin.blumenstingl@googlemail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are no core changes this time, only driver developments.
- New driver for the Dialog Semiconductor DA9062 Power Management
Integrated Circuit (PMIC).
- Renesas SH-PFC has improved consistency, with group and
register checks in the configuration checker.
- New subdriver for the Qualcomm IPQ6018.
- Add the RGMII pin control functionality to Qualcomm IPQ8064.
- Performance and code quality cleanups in the Mediatek
driver.
- Improve the Broadcom BCM2835 support to cover all the GPIOs
that exist in it.
- The Allwinner/Sunxi driver properly masks non-wakeup IRQs on
suspend.
- Add some missing groups and functions to the Ingenic driver.
- Convert some of the Freescale device tree bindings to use the
new and all improved JSON YAML markup.
- Refactorings and support for the SFIO/GPIO in the Tegra194
SoC driver.
- Support high impedance mode in the Spreadtrum/Unisoc driver.
-----BEGIN PGP SIGNATURE-----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=1ZKq
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.7 kernel cycle.
There are no core changes this time, only driver developments:
- New driver for the Dialog Semiconductor DA9062 Power Management
Integrated Circuit (PMIC).
- Renesas SH-PFC has improved consistency, with group and register
checks in the configuration checker.
- New subdriver for the Qualcomm IPQ6018.
- Add the RGMII pin control functionality to Qualcomm IPQ8064.
- Performance and code quality cleanups in the Mediatek driver.
- Improve the Broadcom BCM2835 support to cover all the GPIOs that
exist in it.
- The Allwinner/Sunxi driver properly masks non-wakeup IRQs on
suspend.
- Add some missing groups and functions to the Ingenic driver.
- Convert some of the Freescale device tree bindings to use the new
and all improved JSON YAML markup.
- Refactorings and support for the SFIO/GPIO in the Tegra194 SoC
driver.
- Support high impedance mode in the Spreadtrum/Unisoc driver"
* tag 'pinctrl-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (64 commits)
pinctrl: qcom: fix compilation error
pinctrl: qcom: use scm_call to route GPIO irq to Apps
pinctrl: sprd: Add pin high impedance mode support
pinctrl: sprd: Use the correct pin output configuration
pinctrl: tegra: Add SFIO/GPIO programming on Tegra194
pinctrl: tegra: Renumber the GG.0 and GG.1 pins
pinctrl: tegra: Do not add default pin range on Tegra194
pinctrl: tegra: Pass struct tegra_pmx for pin range check
pinctrl: tegra: Fix "Scmitt" -> "Schmitt" typo
pinctrl: tegra: Fix whitespace issues for improved readability
pinctrl: mediatek: Use scnprintf() for avoiding potential buffer overflow
pinctrl: freescale: drop the dependency on ARM64 for i.MX8M
Revert "pinctrl: mvebu: armada-37xx: use use platform api"
dt-bindings: pinctrl: at91: Fix a typo ("descibe")
pinctrl: meson: add tsin pinctrl for meson gxbb/gxl/gxm
pinctrl: sprd: Fix the kconfig warning
pinctrl: ingenic: add hdmi-ddc pin control group
pinctrl: sirf/atlas7: Replace zero-length array with flexible-array member
pinctrl: sprd: Allow the SPRD pinctrl driver building into a module
pinctrl: Export some needed symbols at module load time
...
In the gxl driver, the sdio cmd and clk pins are inverted. It has not caused
any issue so far because devices using these pins always take both pins
so the resulting configuration is OK.
Fixes: 0f15f500ff ("pinctrl: meson: Add GXL pinctrl definitions")
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Nicolas Belin <nbelin@baylibre.com>
Link: https://lore.kernel.org/r/1582204512-7582-1-git-send-email-nbelin@baylibre.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Dropped the chained IRQ setup callback into GPIOLIB as we
got rid of the last users of that in this changeset.
New drivers:
- New driver for Ingenic X1830.
- New driver for Freescale i.MX8MP.
Driver enhancements:
- Fix all remaining Intel drivers to pass their IRQ chips
along with the GPIO chips.
- Intel Baytrail allocates its irqchip dynamically.
- Intel Lynxpoint is thoroughly rewritten and modernized.
- Aspeed AST2600 pin muxing and configuration is much
improved.
- Qualcomm SC7180 functions are updated and wakeup interrupt
map is provided.
- A whole slew of Renesas SH-PFC cleanups and improvements.
- Fix up the Intel DT bindings to use the generic YAML
DT bindings schema. (A first user of this.)
-----BEGIN PGP SIGNATURE-----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=PnK5
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes, nothing too exciting about
this.
Some changes hit arch/sh and arch/arm but are well isolated and
acknowledged by the respective arch maintainers.
Core changes:
- Dropped the chained IRQ setup callback into GPIOLIB as we got rid
of the last users of that in this changeset.
New drivers:
- New driver for Ingenic X1830.
- New driver for Freescale i.MX8MP.
Driver enhancements:
- Fix all remaining Intel drivers to pass their IRQ chips along with
the GPIO chips.
- Intel Baytrail allocates its irqchip dynamically.
- Intel Lynxpoint is thoroughly rewritten and modernized.
- Aspeed AST2600 pin muxing and configuration is much improved.
- Qualcomm SC7180 functions are updated and wakeup interrupt map is
provided.
- A whole slew of Renesas SH-PFC cleanups and improvements.
- Fix up the Intel DT bindings to use the generic YAML DT bindings
schema (a first user of this)"
* tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: madera: Remove extra blank line
pinctrl: qcom: Don't lock around irq_set_irq_wake()
pinctrl: mvebu: armada-37xx: use use platform api
gpio: Drop the chained IRQ handler assign function
pinctrl: freescale: Add i.MX8MP pinctrl driver support
dt-bindings: imx: Add pinctrl binding doc for i.MX8MP
pinctrl: tigerlake: Tiger Lake uses _HID enumeration
pinctrl: sunrisepoint: Add Coffee Lake-S ACPI ID
pinctrl: iproc: Use platform_get_irq_optional() to avoid error message
pinctrl: dt-bindings: Fix some errors in the lgm and pinmux schema
pinctrl: intel: Pass irqchip when adding gpiochip
pinctrl: intel: Add GPIO <-> pin mapping ranges via callback
pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output
pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pins
pinctrl: sunrisepoint: Add missing Interrupt Status register offset
pinctrl: sh-pfc: Split R-Car H3 support in two independent drivers
pinctrl: artpec6: fix __iomem on reg in set
pinctrl: ingenic: Use devm_platform_ioremap_resource()
pinctrl: ingenic: Factorize irq_set_type function
pinctrl: ingenic: Remove duplicated ingenic_chip_info structures
...
GPIOH_5 and GPIOH_6 can have two Ethernet related functions:
- GPIOH_5 can be ETH_TXD1 or ETH_RXD3
- GPIOH_6 can be ETH_TXD0 or ETH_RXD2
Add the bits for eth_rxd3_h and eth_rxd2_h so the ETH_RXD function can
be disabled when using the ETH_TXD function of GPIOH_{5,6}. No problem
was observed so far, but in theory this could lead to two different
signals being routed to the same pad (which could break Ethernet).
These settings were found in the public "Amlogic Ethernet controller
user guide":
http://openlinux.amlogic.com/@api/deki/files/75/=Amlogic_Ethenet_controller_user_Guide.pdf
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20191226191425.3797490-1-martin.blumenstingl@googlemail.com
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In meson_pinconf_get_drive_strength, variable bit is calculated by
meson_calc_reg_and_bit, this value is the offset from the first pin of a
certain bank to current pin, while Meson SoCs use two bits for each pin
to depict drive-strength. So a left shift by 1 should be done or node
pinconf-pins shows wrong message.
Fixes: 6ea3e3bbef ("pinctrl: meson: add support of drive-strength-microamp")
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Link: https://lore.kernel.org/r/20191226023734.9631-1-qianggui.song@amlogic.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Meson A1 SoC share the same register layout of pinmux with previous
Meson-G12A, however there is difference for gpio and pin config register
in A1. The main difference is that registers before A1 are grouped by
function while those of A1 are by bank. The new register layout is as
below:
/* first bank */ /* addr */
- P_PADCTRL_GPIOP_I base + 0x00 << 2
- P_PADCTRL_GPIOP_O base + 0x01 << 2
- P_PADCTRL_GPIOP_OEN base + 0x02 << 2
- P_PADCTRL_GPIOP_PULL_EN base + 0x03 << 2
- P_PADCTRL_GPIOP_PULL_UP base + 0x04 << 2
- P_PADCTRL_GPIOP_DS base + 0x05 << 2
/* second bank */
- P_PADCTRL_GPIOB_I base + 0x10 << 2
- P_PADCTRL_GPIOB_O base + 0x11 << 2
- P_PADCTRL_GPIOB_OEN base + 0x12 << 2
- P_PADCTRL_GPIOB_PULL_EN base + 0x13 << 2
- P_PADCTRL_GPIOB_PULL_UP base + 0x14 << 2
- P_PADCTRL_GPIOB_DS base + 0x15 << 2
Each bank contains at least 6 registers to be configured, if one bank
has more than 16 gpios, an extra P_PADCTRL_GPIO[X]_DS_EXT is included.
Between two adjacent P_PADCTRL_GPIO[X]_I, there is an offset 0x10, that
is to say, for third bank, the offsets will be 0x20,0x21,0x22,0x23,0x24
,0x25 according to above register layout. For previous chips, registers
are grouped according to their functions while registers of A1 are
according to bank.Also note that there is no AO bank any more in A1.
Current Meson pinctrl driver can cover such change by using base address
of GPIO as that of drive-strength. While simply giving reg_ds = reg_pullen
make wrong value to reg_ds for Socs that do not support drive-strength
like AXG.To make things simple, add an extra dt parser function for
a1 and remain the old dt parser function for only reg parsing.
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Link: https://lore.kernel.org/r/1573819429-6937-3-git-send-email-qianggui.song@amlogic.com
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In meson_pinctrl_parse_dt, it contains two parts: reg parsing and
SoC relative fixup for AO. Several fixups in the same code make it hard
to maintain, so move all fixups to each SoC's callback and make
meson_pinctrl_parse_dt just do the reg parsing, separate these two
parts.Overview of all current Meson SoCs fixup is as below:
+------+--------------------------------------+--------------------------+
| | | |
| SoC | EE domain | AO domain |
+------+--------------------------------------+--------------------------+
|m8 | parse regs: | parse regs: |
|m8b | gpio,mux,pull,pull-enable(skip ds) | gpio,mux,pull(skip ds)|
|gxl | fixup: | fixup: |
|gxbb | no | pull-enable = pull; |
|axg | | |
+------+--------------------------------------+--------------------------+
|g12a | parse regs: | parse regs: |
|sm1 | gpio,mux,pull,pull-enable,ds | gpio,mux,ds |
| | fixup: | fixup: |
| | no | pull = gpio; |
| | | pull-enable = gpio; |
+------+--------------------------------------+--------------------------+
|a1 or | parse regs: |
|later | gpio/mux (without ao domain) |
|SoCs | fixup: |
| | pull = gpio; pull-enable = gpio; ds = gpio; |
+------+-----------------------------------------------------------------+
Since m8-axg share the same ao fixup, make a common function
meson8_aobus_parse_dt_extra to do the job.
Signed-off-by: Qianggui Song <qianggui.song@amlogic.com>
Link: https://lore.kernel.org/r/1573819429-6937-2-git-send-email-qianggui.song@amlogic.com
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190815060718.3286-1-nishkadg.linux@gmail.com
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the missing pinmux for the pwm_a function on the GPIOE_2 pin.
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20190729125838.6498-1-narmstrong@baylibre.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
Core changes:
- Device links can optionally be added between a pin control
producer and its consumers. This will affect how the system
power management is handled: a pin controller will not suspend
before all of its consumers have been suspended. This was
necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense
to make this default in the long run. Right now it is
opt-in per driver.
- Drive strength can be specified in microamps. With decreases
in silicon technology, milliamps isn't granular enough, let's
make it possible to select drive strengths in microamps. Right
now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a
product line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in
addition to muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken
aside and not usable for users. This is used in ACPI systems
to take out some GPIO lines used by the BIOS so that
noone else (neither kernel nor userspace) will play with them
by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board
management controllers for servers) in preparation for the
new Aspeed AST2600 SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=Wdw1
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.3 kernel cycle:
Core changes:
- Device links can optionally be added between a pin control producer
and its consumers. This will affect how the system power management
is handled: a pin controller will not suspend before all of its
consumers have been suspended.
This was necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense to make
this default in the long run.
Right now it is opt-in per driver.
- Drive strength can be specified in microamps. With decreases in
silicon technology, milliamps isn't granular enough, let's make it
possible to select drive strengths in microamps.
Right now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a product
line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in addition to
muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken aside and
not usable for users. This is used in ACPI systems to take out some
GPIO lines used by the BIOS so that noone else (neither kernel nor
userspace) will play with them by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board management
controllers for servers) in preparation for the new Aspeed AST2600
SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes"
* tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits)
pinctrl: aspeed: Strip moved macros and structs from private header
pinctrl: aspeed: Fix missed include
pinctrl: baytrail: Use GENMASK() consistently
pinctrl: baytrail: Re-use data structures from pinctrl-intel.h
pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux()
pinctrl: qcom: Add SM8150 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding
dt-bindings: pinctrl: qcom: Document missing gpio nodes
pinctrl: aspeed: Add implementation-related documentation
pinctrl: aspeed: Split out pinmux from general pinctrl
pinctrl: aspeed: Clarify comment about strapping W1C
pinctrl: aspeed: Correct comment that is no longer true
MAINTAINERS: Add entry for ASPEED pinctrl drivers
dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema
dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema
dt-bindings: pinctrl: aspeed: Split bindings document in two
pinctrl: qcom: Add irq_enable callback for msm gpio
pinctrl: madera: Fixup SPDX headers
pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard
pinctrl: tegra: Add bitmask support for parked bits
...
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation you should have received a
copy of the gnu general public license along with this program if
not see http www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 30 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.962665879@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add pinconf support for PIN_CONFIG_OUTPUT_ENABLE and PIN_CONFIG_OUTPUT
in the meson pinctrl driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
add drive-strength bank regiter and bit value for G12A SoC
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
drive-strength-microamp is a new feature needed for G12A SoC.
the default DS setting after boot is usually 500uA and it is not enough for
many functions. We need to be able to set the drive strength to reliably
enable things like MMC, I2C, etc ...
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
rework bias enable/disable part to prepare drive-strength integration
no functional changes
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No core changes.
New drivers:
- NXP (ex Freescale) i.MX 8QM driver.
- NXP (ex Freescale) i.MX 8MM driver.
- AT91 SAM9X60 subdriver.
Improvements:
- Support for external interrups (EINT) on Mediatek virtual GPIOs.
- Make BCM2835 pin config fully generic.
- Lots of Renesas SH-PFC incremental improvements.
-----BEGIN PGP SIGNATURE-----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=EfXK
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is a calm cycle, not much happened this time around: not even
much incremental development. Some three new drivers, that is all.
No core changes.
New drivers:
- NXP (ex Freescale) i.MX 8QM driver.
- NXP (ex Freescale) i.MX 8MM driver.
- AT91 SAM9X60 subdriver.
Improvements:
- Support for external interrups (EINT) on Mediatek virtual GPIOs.
- Make BCM2835 pin config fully generic.
- Lots of Renesas SH-PFC incremental improvements"
* tag 'pinctrl-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (70 commits)
pinctrl: imx: fix scu link errors
dt-bindings: pinctrl: Document the i.MX50 IOMUXC binding
pinctrl: qcom: spmi-gpio: Reorder debug print
pinctrl: nomadik: fix possible object reference leak
pinctrl: stm32: return error upon hwspinlock failure
pinctrl: stm32: fix memory leak issue
pinctrl: sh-pfc: r8a77965: Add DRIF pins, groups and functions
pinctrl: sh-pfc: r8a77965: Add TMU pins, groups and functions
pinctrl: sh-pfc: Validate fixed-size field widths at build time
pinctrl: sh-pfc: sh73a0: Fix fsic_spdif pin groups
pinctrl: sh-pfc: r8a7792: Fix vin1_data18_b pin group
pinctrl: sh-pfc: r8a7791: Fix scifb2_data_c pin group
pinctrl: sh-pfc: emev2: Add missing pinmux functions
pinctrl: sunxi: Support I/O bias voltage setting on A80
pinctrl: ingenic: Add LCD pins for the JZ4725B SoC
pinctrl: samsung: Remove legacy API for handling external wakeup interrupts mask
pinctrl: bcm2835: Direct GPIO config changes to generic pinctrl
pinctrl: bcm2835: declare pin config as generic
pinctrl: qcom: qcs404: Drop unused UFS_RESET macro
dt-bindings: add documentation for slew rate
...
Fix the mismatch between the "sdxc_d13_1_a" pin group definition from
meson8b_cbus_groups and the entry in sdxc_a_groups ("sdxc_d0_13_1_a").
This makes it possible to use "sdxc_d13_1_a" in device-tree files to
route the MMC data 1..3 pins to GPIOX_1..3.
Fixes: 0fefcb6876 ("pinctrl: Add support for Meson8b")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On the G12a, there is a new 'region' to handle the drive-strength.
This is optional since the older do not have this.
Fixes: 29ae0952e8 ("pinctrl: meson-g12a: add pinctrl driver support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since Meson G12A SoC, Introduce new ao registers AO_RTI_PULL_UP_EN_REG
and AO_GPIO_O.
These bits of controlling output level are remapped to the new register
AO_GPIO_O, and the AO_GPIO_O_EN_N support only controlling output enable.
These bits of controlling pull enable are remapped to the new register
AO_RTI_PULL_UP_EN_REG, and the AO_RTI_PULL_UP_REG support only controlling
pull type(up/down).
The new layout of ao gpio/pull registers is as follows:
- AO_GPIO_O_EN_N [offset: 0x9 << 2]
- AO_GPIO_I [offset: 0xa << 2]
- AO_RTI_PULL_UP_REG [offset: 0xb << 2]
- AO_RTI_PULL_UP_EN_REG [offset: 0xc << 2]
- AO_GPIO_O [offset: 0xd << 2]
From above, we can see ao GPIO registers region has been separated by the
ao pull registers. In order to ensure the continuity of the region on
software, the ao GPIO and ao pull registers use the same base address, but
can be identified by the offset.
Fixes: 29ae0952e8 ("pinctrl: meson-g12a: add pinctrl driver support")
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Gigabit Ethernet requires the Ethernet TXD0..3 and RXD0..3 data lines.
Add the missing eth_rxd2 and eth_rxd3 definitions so we don't have to
rely on the bootloader to set them up correctly.
The vendor u-boot sources for Odroid-C1 use the following Ethernet
pinmux configuration:
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f);
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000);
This translates to the following pin groups in the mainline kernel:
- register 6 bit 0: eth_rxd1 (DIF_0_P)
- register 6 bit 1: eth_rxd0 (DIF_0_N)
- register 6 bit 2: eth_rx_dv (DIF_1_P)
- register 6 bit 3: eth_rx_clk (DIF_1_N)
- register 6 bit 6: eth_tx_en (DIF_3_P)
- register 6 bit 8: eth_ref_clk (DIF_3_N)
- register 6 bit 9: eth_mdc (DIF_4_P)
- register 6 bit 10: eth_mdio_en (DIF_4_N)
- register 6 bit 11: eth_tx_clk (GPIOH_9)
- register 6 bit 12: eth_txd2 (GPIOH_8)
- register 6 bit 13: eth_txd3 (GPIOH_7)
- register 7 bit 20: eth_txd0_0 (GPIOH_6)
- register 7 bit 21: eth_txd1_0 (GPIOH_5)
- register 7 bit 22: eth_rxd3 (DIF_2_P)
- register 7 bit 23: eth_rxd2 (DIF_2_N)
All functions except eth_rxd2 and eth_rxd3 are already supported by the
pinctrl-meson8b driver.
Suggested-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Reviewed-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No core changes this time.
New drivers:
- NXP (ex Freescale) i.MX 8 QXP SoC driver.
- Mediatek MT6797 SoC driver.
- Mediatek MT7629 SoC driver.
- Actions Semiconductor S700 SoC driver.
- Renesas RZ/A2 SoC driver.
- Allwinner sunxi suniv F1C100 SoC driver.
- Qualcomm PMS405 PMIC driver.
- Microsemi Ocelot Jaguar2 SoC driver.
Improvements:
- Some RT improvements (using raw spinlocks where appropriate).
- A lot of new pin sets on the Renesas PFC pin controllers.
- GPIO hogs now work on the Qualcomm SPMI/SSBI pin controller GPIO
chips, and Xway.
- Major modernization of the Intel pin control drivers.
- STM32 pin control driver will now synchronize usage of pins
with another CPU using a hardware spinlock.
-----BEGIN PGP SIGNATURE-----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=cm6m
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"We have no core changes but lots of incremental development in drivers
all over the place: Renesas, NXP, Mediatek and Actions Semiconductor
keep churning out new SoCs.
I have some subtree maintainers for Renesas and Intel helping out to
keep down the load, it's been working smoothly (Samsung also have a
subtree but it was not used this cycle.)
New drivers:
- NXP (ex Freescale) i.MX 8 QXP SoC driver.
- Mediatek MT6797 SoC driver.
- Mediatek MT7629 SoC driver.
- Actions Semiconductor S700 SoC driver.
- Renesas RZ/A2 SoC driver.
- Allwinner sunxi suniv F1C100 SoC driver.
- Qualcomm PMS405 PMIC driver.
- Microsemi Ocelot Jaguar2 SoC driver.
Improvements:
- Some RT improvements (using raw spinlocks where appropriate).
- A lot of new pin sets on the Renesas PFC pin controllers.
- GPIO hogs now work on the Qualcomm SPMI/SSBI pin controller GPIO
chips, and Xway.
- Major modernization of the Intel pin control drivers.
- STM32 pin control driver will now synchronize usage of pins with
another CPU using a hardware spinlock"
* tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (145 commits)
dt-bindings: arm: fsl-scu: add imx8qm pinctrl support
pinctrl: freescale: Break dependency on SOC_IMX8MQ for i.MX8MQ
pinctrl: imx-scu: Depend on IMX_SCU
pinctrl: ocelot: Add dependency on HAS_IOMEM
pinctrl: ocelot: add MSCC Jaguar2 support
pinctrl: bcm: ns: support updated DT binding as syscon subnode
dt-bindings: pinctrl: bcm4708-pinmux: rework binding to use syscon
MAINTAINERS: merge at91 pinctrl entries
pinctrl: imx8qxp: break the dependency on SOC_IMX8QXP
pinctrl: uniphier: constify uniphier_pinctrl_socdata
pinctrl: mediatek: improve Kconfig dependencies
pinctrl: msm: mark PM functions as __maybe_unused
dt-bindings: pinctrl: sunxi: Add supply properties
pinctrl: meson: meson8b: add the missing GPIO_GROUPs for BOOT and CARD
pinctrl: meson: meson8: add the missing GPIO_GROUPs for BOOT and CARD
pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"
pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"
pinctrl: meson: meson8b: fix the GPIO function for the GPIOAO pins
pinctrl: meson: meson8: fix the GPIO function for the GPIOAO pins
pinctrl: sh-pfc: Make pinmux_cfg_reg.var_field_width[] variable-length
...
Add the BOOT and CARD pins as GROUP_GROUPs as well so they can be
configured in devicetree using groups = BOOTx or groups = CARDx. This
makes the behavior consistent with other pins inside the same driver as
well as with the BOOT and CARD pins of the GXBB and GXL pinctrl drivers.
Fixes: 0fefcb6876 ("pinctrl: Add support for Meson8b")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the BOOT and CARD pins as GROUP_GROUPs as well so they can be
configured in devicetree using groups = BOOTx or groups = CARDx. This
makes the behavior consistent with other pins inside the same driver as
well as with the BOOT and CARD pins of the GXBB and GXL pinctrl drivers.
Fixes: 6ac7309511 ("pinctrl: add driver for Amlogic Meson SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the existing "gpio" function to "gpio_periphs". This makes it
consistent with the "gpio_aobus" function. Also GXBB and GXL are also
using the "gpio_periphs" naming, so this makes the code here consistent
with other Amlogic pinctrl drivers.
No functional changes since thee "gpio" function is currently not used.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the existing "gpio" function to "gpio_periphs". This makes it
consistent with the "gpio_aobus" function. Also GXBB and GXL are also
using the "gpio_periphs" naming, so this makes the code here consistent
with other Amlogic pinctrl drivers.
No functional changes since thee "gpio" function is currently not used.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N)
only belong to the pin controller in the AO domain. With the current
definition these pins cannot be referred to in .dts files as group
(which is possible on GXBB and GXL for example).
Add a separate "gpio_aobus" function to fix the mapping between the pin
controller and the GPIO pins in the AO domain. This is similar to how
the GXBB and GXL drivers implement this functionality.
Fixes: 9dab1868ec ("pinctrl: amlogic: Make driver independent from two-domain configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N)
only belong to the pin controller in the AO domain. With the current
definition these pins cannot be referred to in .dts files as group
(which is possible on GXBB and GXL for example).
Add a separate "gpio_aobus" function to fix the mapping between the pin
controller and the GPIO pins in the AO domain. This is similar to how
the GXBB and GXL drivers implement this functionality.
Fixes: 9dab1868ec ("pinctrl: amlogic: Make driver independent from two-domain configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We just changed the code so we apply bias disable on the correct
register but forgot to align the register calculation. The result
is that we apply the change on the correct register, but possibly
at the incorrect offset/bit
This went undetected because offsets tends to be the same between
REG_PULL and REG_PULLEN for a given pin the EE controller. This
is not true for the AO controller.
Fixes: e39f9dd820 ("pinctrl: meson: fix pinconf bias disable")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOX tsin_a pins wrongly uses the SDCard pinctrl bits, this
patch completely removes these pins entries until we find out what
are the correct bits and registers to be used instead.
Fixes: 5a6ae9b801 ("pinctrl: meson-gxl: add tsin_a pins")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AO pull register definition is inverted between pull (up/down) and
pull enable. Fixing this allows to properly apply bias setting
through pinconf
Fixes: 0fefcb6876 ("pinctrl: Add support for Meson8b")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AO pull register definition is inverted between pull (up/down) and
pull enable. Fixing this allows to properly apply bias setting
through pinconf
Fixes: 6ac7309511 ("pinctrl: add driver for Amlogic Meson SoCs")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AO pull register definition is inverted between pull (up/down) and
pull enable. Fixing this allows to properly apply bias setting
through pinconf
Fixes: 468c234f9e ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a bias is enabled on a pin of an Amlogic SoC, calling .pin_config_set()
with PIN_CONFIG_BIAS_DISABLE will not disable the bias. Instead it will
force a pull-down bias on the pin.
Instead of the pull type register bank, the driver should access the pull
enable register bank.
Fixes: 6ac7309511 ("pinctrl: add driver for Amlogic Meson SoCs")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These drivers are GPIO drivers, and the do not need to use the
legacy header in <linux/gpio.h>, go directly for
<linux/gpio/driver.h> instead.
Replace any use of GPIOF_* with 0/1, these flags are for
consumers, not drivers.
Get rid of a few gpio_to_irq() users that was littering
around the place, use local callbacks or avoid using it at
all.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pinctrl driver for Meson-G12A SoC which share the similar IP as
the previous Meson-AXG SoC, both use same pinmux ops (register layout).
A new driver is needed here due to the differences in the pins.
Starting from Meson-AXG SoC, the pinctrl controller block use 4
continues register bits to specific the pin mux function, while comparing
to old generation SoC which using variable length register bits for
the pin mux definition. The new design greatly simplify the software model.
For the detail example, one 32bit register can be divided into 8 parts,
each has 4 bits whose value start from 0 - 7, each can describe one pin,
the value 0 is always devoted to GPIO function, while 1 - 7 devoted to
the mux pin function.
Please note, the GPIOE is actually located at AO (always on) bank.
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pinctrl configuration for gen_clk on gxbb and axg.
gen_clk allows to output and devide several internal clocks of SoC,
including most of the plls.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No core changes this time! Just a calm all-over-the-place
drivers, updates and fixes cycle as it seems.
New drivers/subdrivers:
- Actions Semiconductor S900 driver with more Actions
variants for S700, S500 in the pipe. Also generic GPIO
support on top of the same driver and IRQ support is in
the pipe.
- Renesas r8a77470 PFC support.
- Renesas r8a77990 PFC support.
- Allwinner Sunxi H6 R_PIO support.
- Rockchip PX30 support.
- Meson Meson8m2 support.
- Remove support for the ill-fated Samsung Exynos 5440 SoC.
Improvements:
- Context save/restore support in pinctrl-single.
- External interrupt support for the Mediatek MT7622.
- Qualcomm ACPI HID QCOM8002 supported.
Fixes:
- Fix up suspend/resume support for Exynos 5433.
- Fix Strago DMI fixes on the Intel Cherryview.
-----BEGIN PGP SIGNATURE-----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=6On2
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for v4.18.
No core changes this time! Just a calm all-over-the-place drivers,
updates and fixes cycle as it seems.
New drivers/subdrivers:
- Actions Semiconductor S900 driver with more Actions variants for
S700, S500 in the pipe. Also generic GPIO support on top of the
same driver and IRQ support is in the pipe.
- Renesas r8a77470 PFC support.
- Renesas r8a77990 PFC support.
- Allwinner Sunxi H6 R_PIO support.
- Rockchip PX30 support.
- Meson Meson8m2 support.
- Remove support for the ill-fated Samsung Exynos 5440 SoC.
Improvements:
- Context save/restore support in pinctrl-single.
- External interrupt support for the Mediatek MT7622.
- Qualcomm ACPI HID QCOM8002 supported.
Fixes:
- Fix up suspend/resume support for Exynos 5433.
- Fix Strago DMI fixes on the Intel Cherryview"
* tag 'pinctrl-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: cherryview: limit Strago DMI workarounds to version 1.0
pinctrl: at91-pio4: add missing of_node_put
pinctrl: armada-37xx: Fix spurious irq management
gpiolib: discourage gpiochip_add_pin[group]_range for DT pinctrls
pinctrl: msm: fix gpio-hog related boot issues
MAINTAINERS: update entry for Mediatek pin controller
pinctrl: mediatek: remove unused fields in struct mtk_eint_hw
pinctrl: mediatek: use generic EINT register maps for each SoC
pinctrl: mediatek: add EINT support to MT7622 SoC
pinctrl: mediatek: refactor EINT related code for all MediaTek pinctrl can fit
dt-bindings: pinctrl: add external interrupt support to MT7622 pinctrl
pinctrl: freescale: Switch to SPDX identifier
pinctrl: samsung: Fix suspend/resume for Exynos5433 GPF1..5 banks
pinctrl: sh-pfc: rcar-gen3: Fix grammar in static pin comments
pinctrl: sh-pfc: r8a77965: Add I2C pin support
pinctrl: sh-pfc: r8a77990: Add EthernetAVB pins, groups and functions
pinctrl: sh-pfc: r8a77990: Add I2C{1,2,4,5,6,7} pins, groups and functions
pinctrl: sh-pfc: r8a77990: Add SCIF pins, groups and functions
pinctrl: sh-pfc: r8a77990: Add bias pinconf support
pinctrl: sh-pfc: Initial R8A77990 PFC support
...
