The flag of RTL8152_UNPLUG should only be set when the device is
unplugged, not each time the rtl8152_disconnect() is called.
Otherwise, the device wouldn't be stopped normally.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_carrier_off would be called when autoresuming, even though
the cable is plugged. This causes some applications do relative
actions when detecting the carrier off. Keep the status of the
carrier, and let it be modified when the linking change occurs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hw is in ALDPS mode, the hw may have no response for accessing
the most registers. Therefore, the ALDPS should be disabled before
accessing the hw in rtl_ops.init(), rtl_ops.disable(), rtl_ops.up(),
and rtl_ops.down(). Regardless of rtl_ops.enable(), because the hw
wouldn't enter ALDPS mode when linking on. The hw would enter the
ALDPS mode after several seconds when link down occurs and the ALDPS
is enabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the usb speed of the RTL8152 is not high speed, the USB_DEV_STAT[2:1]
should be equal to [0 1]. That is, the STAT_SPEED_FULL should be equal
to 2.
There is a easy way to check the usb speed by the speed field of the
struct usb_device. Use it to replace the original metheod.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Spotted-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The transport offset of the IPv4 packet should be fixed and wouldn't
be out of the hw limitation, so the r8152_csum_workaround() should
be used for IPv6 packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum jumbo frame size for RTL8153 is 9K bytes.
Change the max rx packet size to 9K.
Change the use of the shared fifo from 6K (default) to 12K for tx.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device should be waked up from runtime suspend before dumping
the hw counter.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the system is too busy to complete the urb, the tx timout function
would be called. This causes the other tx urbs would be killed, too.
Increase the tx timeout to avoid it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device is unplugged, the driver would try to disable the
device. Add checking the flag of RTL8152_UNPLUG to skip setting
the device when it is unplugged. This could shorten the time of
unloading the driver.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_cow_head() before editing the tx packet header. The header
would be reallocated if it is shared.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support hw IPv6 checksum for TCP and UDP packets.
Note that the hw has the limitation of the range of the transport
offset. Besides, the TCP Pseudo Header of the IPv6 TSO of the hw
bases on the Microsoft document which excludes the packet length.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support scatter gather and TSO.
Adjust the tx checksum function and set the max gso size to fix the
size of the tx aggregation buffer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Continue dealing with the remain rx packets, even though the allocation
of the skb fail. This could calculate the correct dropped packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
move the tx_bottom() from delayed_work to tasklet. It makes the rx
and tx balanced. If the device is in runtime suspend when getting
the tx packet, wakeup the device before trasmitting.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check tx agg list before spin lock to avoid doing spin lock every
times.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use spin_lock and spin_unlock in interrupt context.
The ndo_start_xmit would not be called in interrupt context, so
replace the relative spin_lock_irqsave and spin_unlock_irqrestore
with spin_lock_bh and spin_unlock_bh.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rtl8152_get_stats() returns the point address of the struct
net_device_stats. This could be got from struct net_device directly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add or remove some empty lines. Replace the spaces with the tabs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are known issues for switching the drivers between ECM mode and
vendor mode. The interrup transfer may become abnormal. The hardware
may have the opportunity to die if you change the configuration without
unloading the current driver first, because all the control transfers
of the current driver would fail after the command of switching the
configuration.
Although to use the ecm driver and vendor driver independently is fine,
it may have problems to change the driver from one to the other by
switching the configuration. Additionally, now the vendor mode driver
is more powerful than the ECM driver. Thus, disable the ECM mode driver,
and let r8152 to set the configuration to vendor mode and reset the
device automatically.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace netif_rx with netif_receive_skb to avoid disabling irq frequently
for increasing the efficiency.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support runtime suspend for RTL8152 and RTL8153.
Move tx_bottom() from tasklet to delayed_work. That avoids to
transmit tx packets after calling autosuspend.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add up method for rtl_ops and asign relative functions. Move
clear_bp() and hw_phy_cfg() from init method to up method of rtl_ops.
Call rtl_ops.up() for ndo_open() and rtl_ops.down for ndo_stop().
Replace allocating the memory in probe() with in ndo_open().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY reset is necessary after some hw settings. However, it would
cause the linking down, and so does the set_speed function. Combine
the PHY reset with set_speed function. That could reduce the frequency
of linking down and accessing the PHY register.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the method of enabling the PHY to clear BMCR_PDOWN only.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace getting one item from a list with getting the whole list one time.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for RTL_VER_01, replace loading the MAC address from PLA_IDR
with from PLA_BACKUP. The default MAC address may be modified by
the other OS, so the PLA_IDR may be not the default MAC address.
The data in the PLA_BACKUP address of the RTL_VER_01 may be destoryed,
so load MAC address from PLA_IDR for RTL_VER_01.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the following functions.
- r8153_u1u2en
- r8153_u2p3en
- r8153_power_cut_en
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace some codes with the following three functions.
- rtl_drop_queued_tx
- rxdy_gated_en
- r8152_power_cut_en
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the following functions which is for the further coding.
- rtl_clear_bp
- r8153_clear_bp
- r8153_teredo_off
- r8152b_disable_aldps
- r8152b_enable_aldps
- r8152b_hw_phy_cfg
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The submission of the interrupt transfer should be done after setting
the bit of WORK_ENABLE, otherwise the callback function would have
the opportunity to be returned directly.
Clear the bit of WORK_ENABLE before killing the interrupt transfer.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the limitation that the ecm and r8152 drivers couldn't coexist.
- Remove the devices from the blacklist of relative drivers.
- Remove usb_driver_set_configuration() from r8152 driver.
- Modify the id_table of the r8152 driver for the vendor mode only.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warnings and error:
- WARNING: usb_free_urb(NULL) is safe this check is probably not required
- WARNING: kfree(NULL) is safe this check is probably not required
- ERROR: do not use C99 // comments
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The r8152 could support RTL8153. Update the relative descriptor.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Replace pr_warn_ratelimited() with net_ratelimit() and netdev_warn().
- Adjust the algnment of some messages.
- Remove the peroid.
- Fix some messages don't have terminating newline.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the boolean value with the error code for the return value
of the rtl_ops_init().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some information of the device may be used in other functions. Move
the relative code to make sure it would be initialzed correctly
before using it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the tabs of the variables declaration with the spaces.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
