Shifting a u8 by 24 will cause the value to be promoted to an integer. If
the top bit of the u8 is set then the following conversion to an unsigned
long will sign extend the value causing the upper 32 bits to be set in
the result.
Fix this by casting the u8 value to an unsigned long before the shift.
Detected by CoverityScan, CID#1309693 ("Unintended sign extension")
Fixes: 9a9a54ad7a ("drivers/rtc: add support for Qualcomm PMIC8xxx RTC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Shifting a u8 by 24 will cause the value to be promoted to an integer. If
the top bit of the u8 is set then the following conversion to an unsigned
long will sign extend the value causing the upper 32 bits to be set in
the result.
Fix this by casting the u8 value to an unsigned long before the shift.
Detected by CoverityScan, CID#714646-714649 ("Unintended sign extension")
Fixes: 2985c29c19 ("rtc: Add rtc support to 88PM80X PMIC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Shifting a u8 by 24 will cause the value to be promoted to an integer. If
the top bit of the u8 is set then the following conversion to an unsigned
long will sign extend the value causing the upper 32 bits to be set in
the result.
Fix this by casting the u8 value to an unsigned long before the shift.
Detected by CoverityScan, CID#144925-144928 ("Unintended sign extension")
Fixes: 008b30408c ("mfd: Add rtc support to 88pm860x")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When the EXTENSION.WADA bit is set, register 0x19 contains a bitmap of
week days, not a day of month. As Linux only handles a single alarm
without repetition using day of month is more flexible, so clear this
bit. (Otherwise a value depending on time.tm_wday would have to be
written to register 0x19.)
Also optimize setting the AIE bit to use a single register write instead
of a bulk write of three registers.
Fixes: ee0981be77 ("rtc: ds1307: Add support for Epson RX8130CE")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When voltage dropped since the RTC was last set the reported time is not
reliable. In this case return an error indicator instead of a bogus
time.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
While rx8130 has a register offset of 0x10 in its chip_desc, this isn't
used when regmap accesses are done. So add 0x10 to access the right
locations.
Fixes: ee0981be77 ("rtc: ds1307: Add support for Epson RX8130CE")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There used to be 16 declarations for static functions. By just adding a
declaration for the chips array and reordering the functions the 16
function declarations can be dropped.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This allows to use the register offsets in all functions
which is needed in one of the next patches.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patch adds i.MX system controller RTC set time support, the
RTC set time is implemented via SIP(silicon provider) runtime
service call and ARM-Trusted-Firmware will communicate with system
controller via MU(message unit) IPC to set RTC time.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Ricoh chips have slightly different register layouts
and the r2221 chip uses bit 5 as the oscillator halt sensor bit.
Signed-off-by: Olive Rohe <oliver.rohe@wago.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
During system suspend, the SNVS RTC's clock will be disabled in
noirq suspend phase, but SNVS RTC's alarm interrupt could still
arrive, system will hang if SNVS RTC driver tries to access register
without clock enabled, this patch fixes the issue of this scenario.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Shifting a u8 by 24 will cause the value to be promoted to an integer. If
the top bit of the u8 is set then the following conversion to an unsigned
long will sign extend the value causing the upper 32 bits to be set in
the result.
Fix this by casting the u8 value to an unsigned long before the shift.
Detected by CoverityScan, CID#138801 ("Unintended sign extension")
Fixes: edf1aaa31f ("[PATCH] RTC subsystem: DS1672 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RV1805 uses smaller package than the AB1805, discern those two
chips based on the compatible value and configure reserved bits in
the RV1805 to prevent current leakage and accidental test mode entry.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
To: linux-rtc@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patch adds a driver for Cadence RTC controller.
It can be enabled with RTC_DRV_CADENCE Kconfig option.
It supports waking system from sleep modes.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Older versions of Libreboot and Coreboot had an invalid value
(`3' in my case) in the century byte affecting the GM45 in
the Thinkpad X200. Not everybody's updated their firmwares,
and Linux <= 4.2 was able to read the RTC without problems,
so workaround this by ignoring invalid values.
Fixes: 3c217e51d8 ("rtc: cmos: century support")
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sylvain Chouleur <sylvain.chouleur@intel.com>
Cc: Patrick McDermott <patrick.mcdermott@libiquity.com>
Cc: linux-rtc@vger.kernel.org
Signed-off-by: Eric Wong <e@80x24.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When i2c_smbus_read_i2c_block_data() fails, the read data in "buf" could
be incorrect and should not be used. The fix checks if
i2c_smbus_read_i2c_block_data fails, and if so, return its error code
upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
clk_prepare() could fail, so let's check its status and if it fails
return its error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add support for specifying the xtal load capacitance in the DT node.
The pcf85063 supports xtal load capacitance of 7pF or 12.5pF.
If the rtc has the wrong configuration the time will
drift several hours/week.
The driver use the default value 7pF.
The DT may specify either 7000fF or 12500fF.
(The DT uses femto Farad to avoid decimal numbers).
Other values are warned and the driver uses the default value.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Urs Fässler <urs.fassler@bbv.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add support for specifying the xtal load capacitance in the DT node.
The pcf8523 supports xtal load capacitance of 7pF or 12.5pF.
If the rtc has the wrong configuration the time will
drift several hours/week.
The driver use the default value 12.5pF.
The DT may specify either 7000fF or 12500fF.
(The DT uses femto Farad to avoid decimal numbers).
Other values are warned and the driver uses the default value.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Replace of_match_node() with of_device_get_match_data(), which removes a
few lines of code from the driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
s3c_rtc_enable/disable_clk() functions were designed to be called multiple
times without reference counting, because they were initially only used in
alarm setting/clearing functions, which can be called both when alarm is
already set or not. Later however, calls to those functions have been added to
other places in the driver - like time and /proc reading callbacks, what
results in broken alarm if any of such events happens after the alarm has
been set. Fix this by simplifying s3c_rtc_enable/disable_clk() functions
to rely on proper reference counting in clock core and move alarm enable
counter to s3c_rtc_setaie() function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fixes the following sparse warning:
drivers/rtc/rtc-sd3078.c:218:19: warning:
symbol 'sd3078_driver' was not declared. Should it be static?
Fixes: 1d67a23210 ("rtc: sd3078: new driver.")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
isl1208_i2c_get_dtr() was returning the dtr value directly, but could
also return a negative error code. Negative trimming values, e.g. -20,
would get interpreted as an error code, e.g. -ENOTDIR.
This patch offsets the dtr value by 100 so it's positive and won't alias
an error code.
Also fix check that considered a return value of -1 to be success.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Users may call 'ioctl' and pass a very big value on 'tm->tm_year'.
It can be overflowed in 'int' after add 1900.
In function 'rtc_month_days' and 'mktime64', also treated it as an
'unsigned' parameter.
UBSAN: Undefined behaviour in drivers/rtc/rtc-lib.c:103:59
signed integer overflow:
2147483647 + 1900 cannot be represented in type 'int'
UBSAN: Undefined behaviour in drivers/rtc/rtc-lib.c:119:30
signed integer overflow:
2147483647 + 1900 cannot be represented in type 'int'
So, covert it to 'unsigned' explicitly.
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The sd3078 is a combination RTC and SRAM device with I2C interface.
Signed-off-by: Dianlong Li <long17.cool@163.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Subsystem:
- new %ptR printk format
- rename core files
- allow registration of multiple nvmem devices
New driver:
- i.MX system controller RTC
Drivers:
- abx80x: handle voltage ioctls, correct binding doc
- m41t80: correct month in alarm reads
- pcf85363: add pcf85263 support
- pcf8523: properly handle battery low flag
- s3c: limit alarm to one year in the future as ALMYEAR is broken
- sun6i: rework clock output binding
-----BEGIN PGP SIGNATURE-----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=5He5
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- new %ptR printk format
- rename core files
- allow registration of multiple nvmem devices
New driver:
- i.MX system controller RTC
Driver updates:
- abx80x: handle voltage ioctls, correct binding doc
- m41t80: correct month in alarm reads
- pcf85363: add pcf85263 support
- pcf8523: properly handle battery low flag
- s3c: limit alarm to one year in the future as ALMYEAR is broken
- sun6i: rework clock output binding"
* tag 'rtc-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (54 commits)
rtc: rename core files
rtc: nvmem: fix possible use after free
rtc: add i.MX system controller RTC support
dt-bindings: fsl: scu: add rtc binding
rtc: pcf2123: Add Microcrystal rv2123
rtc: class: reimplement devm_rtc_device_register
rtc: enforce rtc_timer_init private_data type
rtc: abx80x: Implement RTC_VL_READ,CLR ioctls
rtc: pcf85363: Add support for NXP pcf85263 rtc
dt-bindings: rtc: pcf85363: Document pcf85263 real-time clock
rtc: pcf8523: don't return invalid date when battery is low
dt-bindings: rtc: use a generic node name for ds1307
PM: Switch to use %ptR
m68k/mac: Switch to use %ptR
Input: hp_sdc_rtc - Switch to use %ptR
rtc: tegra: Switch to use %ptR
rtc: s5m: Switch to use %ptR
rtc: s3c: Switch to use %ptR
rtc: rx8025: Switch to use %ptR
rtc: rx6110: Switch to use %ptR
...
Rename core files so there is a clearer separation between the RTC core and
the RTC drivers.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In cas of probe failure, devres may free the memory allocated for
rtc->nvram before devm_rtc_release_device() is called. This leads to
rtc_nvram_unregister using it after being freed which may lead to a crash.
This has been shown to happen after commit 461e557b97 ("rtc: nvmem: use
devm_nvmem_register()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
i.MX8QXP is an ARMv8 SoC which has a Cortex-M4 system controller
inside, the system controller is in charge of controlling power,
clock and secure rtc etc..
This patch adds i.MX system controller RTC driver support,
Linux kernel has to communicate with system controller via MU
(message unit) IPC to set/get RTC time and other alarm functions,
since the RTC set time needs to be done in secure EL3 mode (required
by system controller firmware) and alarm functions needs to be done
with general MU IRQ handle, these depend on other components which
are NOT ready, so this patch ONLY enables the RTC time read.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add a compatible string for Microcrystal rv2123 as the reset procedure seem
to be differing. However, the current driver works just fine.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Implement devm_rtc_device_register using devm_rtc_allocate_device and
__rtc_register_device so there is only one path left to register rtc
devices.
Also mark it as deprecated so new drivers will hopefully use
devm_rtc_allocate_device and rtc_register_device that are less race prone
and allow avoiding the 2038, 2070, 2100 and 2106 bugs properly.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
All the remaining users of rtc_timers are passing the rtc_device as private
data. Enforce that and rename private_data to rtc.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Implement standard ioctls for polling the battery status and clearing
the battery low indication from userspace.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add support for NXP pcf85263 real-time clock. pcf85263 rtc is compatible
with pcf85363,except that pcf85363 has additional 64 bytes of RAM.
1 byte of nvmem is supported and exposed in sysfs (# is the instance
number,starting with 0): /sys/bus/nvmem/devices/pcf85x63-#/nvmem
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC_VL_READ ioctl reports the low battery condition. Still,
pcf8523_rtc_read_time() happily returns invalid dates in this case.
Check the battery health on pcf8523_rtc_read_time() to avoid that.
Reported-by: Erik Čuk <erik.cuk@domel.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Note, we drop the validation option. This is only used in
a deprecated ABI and is mostly wrong as many RTCs will still be valid
after 2100.
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The bindings have been updated to expose the RTC's internal oscillator,
for some SoCs that have it directly feeding the PRCM block. The changes
include the index 2 for the clock outputs, as well as the clock output
names.
This patch adds the internal oscillator to the list of clocks exposed
through of_clk_add_hw_provider(), and also have the driver optionally
fetch the name of the clock from the device tree if it's available.
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There are different variants to the RTC hardware first seen on sun6i
(A31). The differences we care about in this driver are the clock rate
for the internal oscillator, prescalers, and the presence of an external
clock output.
This patch adds support for all the known pre-H6 base compatibles using
the variants data structure previously introduced.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Amongst the Allwinner SoCs that have seen some kind of coverage by the
linux-sunxi community, whether it be mainline Linux or U-boot support,
or just available datasheets, most newer chips use the RTC design first
seen in the A31 (sun6i).
Overall there have been some minor differences. This patch covers the
following:
- average clock rate of the internal RC oscillator
+ presence of fixed and adjustable prescaler for this clock
- availability of an external (to the SoC) clock output
One major difference regarding the H6 is the 24 MHz crystal is now
routed through the RTC, as a digitally compensated oscillator (DCXO).
This is not covered in this patch and will be supported later.
Other differences are either unrelated to RTC or clock functionality,
such as boot or crypto related registers, or the driver simply doesn't
use the feature in question. One example of the latter is the
calibration function for the RC oscillator. We consider this clock to
be very bad and avoid using it.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC's main clock, used internally and exported to the rest of the
SoC, is called "LOSC" (low speed oscillator) through the hardware
documentation.
This patch adds a default name for this clock, in case the device tree
does not provide one. This shouldn't happen, but lets play it safe.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Here are some small IIO and Staging driver fixes for 4.20-rc5.
Nothing major, the IIO fix ended up touching the HID drivers at the same
time, but the HID maintainer acked it. The staging fixes are all minor
patches for reported issues and regressions, full details are in the
shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXAFeeA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykZSQCgm8wafCzK2b9YjeUmAxFJQCKkK7YAnjHSqa8N
FwSpP/zei0mtZgw6Rzj9
=cBhw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here are some small IIO and staging driver fixes for 4.20-rc5.
Nothing major, the IIO fix ended up touching the HID drivers at the
same time, but the HID maintainer acked it. The staging fixes are all
minor patches for reported issues and regressions, full details are in
the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.20-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio/hid-sensors: Fix IIO_CHAN_INFO_RAW returning wrong values for signed numbers
staging: vchiq_arm: fix compat VCHIQ_IOC_AWAIT_COMPLETION
staging: mt7621-pinctrl: fix uninitialized variable ngroups
staging: rtl8723bs: Add missing return for cfg80211_rtw_get_station
staging: most: use format specifier "%s" in snprintf
staging: rtl8723bs: Fix incorrect sense of ether_addr_equal
staging: mt7621-dma: fix potentially dereferencing uninitialized 'tx_desc'
staging: comedi: clarify/unify macros for NI macro-defined terminals
drivers: staging: cedrus: find ctx before dereferencing it ctx
staging: rtl8723bs: Fix the return value in case of error in 'rtw_wx_read32()'
staging: comedi: ni_mio_common: scale ao INSN_CONFIG_GET_CMD_TIMING_CONSTRAINTS
iio:st_magn: Fix enable device after trigger
The Linux i2c layer has functions to execute common SMBUS/I2C
transactions. The register access code here is identical to the I2C
read/write block data routines.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In case of error, we return 0.
This is spurious and not consistent with the other functions of the driver.
Propagate the error code instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Using devm_nvmem_register allows to avoid tracking the nvmem pointer in the
rtc_device structure.
This ultimately allows to register multiple nvmem devices from an RTC
driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Before this commit sensor_hub_input_attr_get_raw_value() failed to take
the signedness of 16 and 8 bit values into account, returning e.g.
65436 instead of -100 for the z-axis reading of an accelerometer.
This commit adds a new is_signed parameter to the function and makes all
callers pass the appropriate value for this.
While at it, this commit also fixes up some neighboring lines where
statements were needlessly split over 2 lines to improve readability.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In case of error, we return 0.
This is spurious and not consistent with the other functions of the driver.
Commit e115a2bf14 has modified more than what is said in the commit
message. Reverse part of it znd return an error when needed, as it was
previously.
Fixes: e115a2bf14 ("rtc: max77686: stop validating rtc_time in .read_time")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
(RTC,ALM)YEAR registers of Exynos built-in RTC device contains 3 BCD
characters. s3c-rtc driver uses only 2 lower of them and supports years
from 2000..2099 range. The third BCD value is typically set to 0, but it
looks that handling of it is broken in the hardware. It sometimes
defaults to a random (even non-BCD) value. This is not an issue
for handling RTCYEAR register, because bcd2bin() properly handles only
8bit values (2 BCD characters, the third one is skipped). The problem
is however with ALMYEAR register and proper RTC alarm operation. When
YEAREN bit is set for the configured alarm, RTC hardware triggers alarm
only when ALMYEAR and RTCYEAR matches. This usually doesn't happen
because of the random noise on the third BCD character.
Fix this by simply skipping setting ALMYEAR register in alarm
configuration. This workaround fixes broken alarm operation on Exynos
built-in rtc device. My tests revealed that the issue happens on the
following Exynos series: 3250, 4210, 4412, 5250 and 5410.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Complement commit 85d77047c4 ("drivers/rtc/rtc-m41t80.c: propagate
error value from smbus functions") and correct the remaining places that
fail to propagate the error code from SMBus calls.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
References: 85d77047c4 ("drivers/rtc/rtc-m41t80.c: propagate error value from smbus functions")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add the missing adjustment of the month range on alarm reads from the
RTC, correcting an issue coming from commit 9c6dfed92c ("rtc: m41t80:
add alarm functionality"). The range is 1-12 for hardware and 0-11 for
`struct rtc_time', and is already correctly handled on alarm writes to
the RTC.
It was correct up until commit 48e9766726 ("drivers/rtc/rtc-m41t80.c:
remove disabled alarm functionality") too, which removed the previous
implementation of alarm support.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Fixes: 9c6dfed92c ("rtc: m41t80: add alarm functionality")
References: 48e9766726 ("drivers/rtc/rtc-m41t80.c: remove disabled alarm functionality")
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
devm_rtc_device_unregister is not used by any driver and should not be used
by any new driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
As original license mentioned, it is GPL-2.0 in SPDX.
Then, MODULE_LICENSE() should be "GPL v2" instead of "GPL".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Trivial fix to clean up indentation issues, remove spaces, add missing
tabs
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Clang warns when one enumerated type is implicitly converted to another:
drivers/rtc/rtc-omap.c:574:21: warning: implicit conversion from
enumeration type 'enum rtc_pin_config_param' to different enumeration
type 'enum pin_config_param' [-Wenum-conversion]
{"ti,active-high", PIN_CONFIG_ACTIVE_HIGH, 0},
~ ^~~~~~~~~~~~~~~~~~~~~~
drivers/rtc/rtc-omap.c:579:12: warning: implicit conversion from
enumeration type 'enum rtc_pin_config_param' to different enumeration
type 'enum pin_config_param' [-Wenum-conversion]
PCONFDUMP(PIN_CONFIG_ACTIVE_HIGH, "input active high", NULL, false),
~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
./include/linux/pinctrl/pinconf-generic.h:163:11: note: expanded from
macro 'PCONFDUMP'
.param = a, .display = b, .format = c, .has_arg = d \
^
2 warnings generated.
It is expected that pinctrl drivers can extend pin_config_param because
of the gap between PIN_CONFIG_END and PIN_CONFIG_MAX so this conversion
isn't an issue. Most drivers that take advantage of this define the
PIN_CONFIG variables as constants, rather than enumerated values. Do the
same thing here so that Clang no longer warns.
Link: https://github.com/ClangBuiltLinux/linux/issues/144
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix an issue with the 32-bit range error path in `rtc_hctosys' where no
error code is set and consequently the successful preceding call result
from `rtc_read_time' is propagated to `rtc_hctosys_ret'. This in turn
makes any subsequent call to `hctosys_show' incorrectly report in sysfs
that the system time has been set from this RTC while it has not.
Set the error to ERANGE then if we can't express the result due to an
overflow.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Fixes: b3a5ac42ab ("rtc: hctosys: Ensure system time doesn't overflow time_t")
Cc: stable@vger.kernel.org # 4.17+
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When there is no IRQ configured for the RTC, the rtc-cmos code does not
support alarms, all alarm rtc_ops fail with -EIO / -EINVAL.
The rtc-core expects a rtc driver which does not support rtc alarms to
not have alarm ops at all. Otherwise the wakealarm sysfs attr will read
as empty rather then returning an error, making it impossible for
userspace to find out beforehand if alarms are supported.
A system without an IRQ for the RTC before this patch:
[root@localhost ~]# cat /sys/class/rtc/rtc0/wakealarm
[root@localhost ~]#
After this patch:
[root@localhost ~]# cat /sys/class/rtc/rtc0/wakealarm
cat: /sys/class/rtc/rtc0/wakealarm: No such file or directory
[root@localhost ~]#
This fixes gnome-session + systemd trying to use suspend-then-hibernate,
which causes systemd to abort the suspend when writing the RTC alarm fails.
BugLink: https://github.com/systemd/systemd/issues/9988
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When registering one RTC device, it will check to see if there is an
alarm already set in RTC hardware by reading RTC alarm, at this time
we should always read the normal alarm put in always-on region by
checking the rtc->registered flag.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC interrupt enable register is not put in always-power-on region
supplied by VDDRTC, so we should check if we need enable the alarm
interrupt when system booting.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When registering one rtc device, it will check to see if there is an
alarm already set in rtc hardware by issuing __rtc_read_alarm(). So
we should not disable the RTC interrupts and clear the interrupts
status in probe() function.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
We should clear the SPG value update interrupt status once the SPG value
is updated successfully, in case incorrect status validation for next time.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Set wakeup capability before registering rtc device, in case the alarmtimer
can find one available rtc device.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Clang warns:
drivers/rtc/rtc-s35390a.c:124:27: warning: implicit conversion from
'int' to 'char' changes value from 192 to -64 [-Wconstant-conversion]
buf = S35390A_FLAG_RESET | S35390A_FLAG_24H;
~ ~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~
1 warning generated.
Update buf to be an unsigned 8-bit integer, which matches the buf member
in struct i2c_msg.
https://github.com/ClangBuiltLinux/linux/issues/145
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced "Fall" with a proper
"Fall through" comment.
Addresses-Coverity-ID: 1373875 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Instead of confusingly returning -EBUSY on failure to obtain an
interrupt, propagate the real error code. While at it, let the user know
why the interrupt could not be acquired.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix a problem with commit 311ee9c151 ("rtc: cmos: allow using ACPI for
RTC alarm instead of HPET") defining `use_acpi_alarm' module parameter
even for non-ACPI platforms, which ignore it. Wrap the definition into
#ifdef CONFIG_ACPI and use a static inline wrapper function, hardcoded
to return 0 and consequently optimized away for !ACPI, following the
existing pattern with HPET handling functions.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Fixes: 311ee9c151 ("rtc: cmos: allow using ACPI for RTC alarm instead of HPET")
Cc: stable@vger.kernel.org # 4.18+
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix a commit 311ee9c151 ("rtc: cmos: allow using ACPI for RTC alarm
instead of HPET") `rtc-cmos' regression causing a link error:
drivers/rtc/rtc-cmos.o: In function `cmos_platform_probe':
rtc-cmos.c:(.init.text+0x33c): undefined reference to `hpet_rtc_interrupt'
rtc-cmos.c:(.init.text+0x3f4): undefined reference to `hpet_rtc_interrupt'
with non-ACPI platforms using this driver. The cause is the change of
the condition guarding the use of `hpet_rtc_interrupt'.
Previously it was a call to `is_hpet_enabled'. That function is static
inline and has a hardcoded 0 result for non-ACPI platforms, which imply
!HPET_EMULATE_RTC. Consequently the compiler optimized the whole block
away including the reference to `hpet_rtc_interrupt', which never made
it to the link stage.
Now the guarding condition is a call to `use_hpet_alarm', which is not
static inline and therefore the compiler may not be able to prove that
it actually always returns 0 for non-ACPI platforms. Consequently the
build breaks with an unsatisfied reference, because `hpet_rtc_interrupt'
is nowhere defined at link time.
Fix the problem by marking `use_hpet_alarm' inline. As the `inline'
keyword serves as an optimization hint rather than a requirement the
compiler is still free to choose whether inlining will be beneficial or
not for ACPI platforms.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Fixes: 311ee9c151 ("rtc: cmos: allow using ACPI for RTC alarm instead of HPET")
Cc: stable@vger.kernel.org # 4.18+
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Instead of lying to the core when the alarm is invalid, let it handle that
by returning the error.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com> (on Armada 375 DB)
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call the 64bit versions of rtc_time_to_tm now that the range is enforced by
the core.
Also remove the open coded rtc_tm_to_time64.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
rtc_time_to_tm always rturns a valid tm, there is no need to validate it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Let the core handle offsetting and windowing the RTC range.
The RTC has a 24 bit counter for minutes plus a seconds counter.
Keep the epoch at the beginning of 2000.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use rtc_add_group to add the sysfs group in a race free manner.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Instead of resetting the RTC to an bogus valid time, let userspace know
that the time is invalid when XSTP is set. Reset XSTP when setting the time
again.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The name passed to devm_rtc_device_register is now unused. anyway, switch
to devm_rtc_allocate_device to avoid forward declaring rs5c348_driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Call the 64bit versions of rtc_time_to_tm and rtc_tm_to_time now that the
range is enforced by the core.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The IRQ is requested before the struct rtc is allocated and registered, but
this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
before requesting the IRQ.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Register frequency test using rtc_add_group to avoid a possible race
condition and simplify the code.
This also moves the attribute to its proper location under the rtc device
instead of the i2c parent device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Instead of adding a binary sysfs attribute from the driver, use the core to
register an nvmem device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
/proc is not the correct ABI to display debugging info. Remove
RTC_DS1685_PROC_REGS as the driver hasn't seen any real development since
it was included.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The license text is specifying GPL v2 only but the MODULE_LICENSE is set to
GPL which means GNU Public License v2 or later. When MODULE_LICENSE and
boiler plate does not match, go for boiler plate license.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The default word_size and stride of 1 are correct for the tx4939. Also fix
the nvmem folder name.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The core header file is reserved for the core, stop including it.
Also reorder includes alphabetically.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Move rtc_add_group and rtc_add_groups definition to rtc.h that is available
for all RTC drivers.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
On m41txx you can enable open-drain OUT pin to check if offset is ok.
Enabling OUT pin with frequency_test_enable attribute, OUT pin will tick
512 times faster than 1s tick base.
Enable or Disable FT bit on CONTROL register if freq_test is 1 or 0.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
m41txx chips can hold a calibration value to get correct clock bias.
Add offset handling (ranging between -63ppm and 126ppm) via sysfs.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use rtc_add_group to add the common sysfs group to avoid a possible race
condition.
[Denis.Osterland@diehl.com: use to_i2c_client(dev->parent)]
Signed-off-by: Denis Osterland <Denis.Osterland@diehl.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The move of atrim, dtrim usr sysfs properties from i2c device
to rtc device require to access them via dev->parent.
This patch also aligns timestamp0.
Stale mentions of irq_task are left in the kerneldoc after its removal.
Remove them.
There is still one indirect mention left but commit 3c8bb90efb ("rtc: Fix
hrtimer deadlock") can probably be reverted now.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Ensure the non managed version of the un/registration functions is not used
anymore. No driver is using it anymore and they should not be necessary.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The abx804 and abx805 chips have support for a simple watchdog
function that can trigger an external reset.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This will allow additional data to be tracked, for future
improvements.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Switch to devm_rtc_allocate_device to simplify the erro and driver removal
paths.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The IRQ is requested before the struct rtc is allocated and registered, but
this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
before requesting the IRQ.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The IRQ is requested before the struct rtc is allocated and registered, but
this struct is used in the IRQ handler. This may lead to a NULL pointer
dereference.
Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
before requesting the IRQ.
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/rtc/rtc-mrst.c: In function 'mrst_procfs':
drivers/rtc/rtc-mrst.c:264:29: warning:
variable 'valid' set but not used [-Wunused-but-set-variable]
unsigned char rtc_control, valid;
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Epson rx8803 is mostly similar to the Microcrystal RV8803 but the size
of the offset register is 4 bits vs 6 bits but it has a configurable
temperature compensation.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
devm_kcalloc() returns NULL, it never returns error pointers. In the
current code we would return PTR_ERR(NULL) which is success, instead of
returning the -ENOMEM error code.
Fixes: a0a1a1ba30 ("rtc: sysfs: facilitate attribute add to rtc device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Depending on MACH_INGENIC prevent us from creating a generic kernel that
works on more than one MIPS board. Instead, we just depend on MIPS being
set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cut down the shutdown time from 2 seconds to 1 sec. In case of roll
over try again.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use of_device_is_system_power_controller instead of manually reading
the system-power-controller property from the device tree node.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
mrst_read_time() is never called in atomic context.
It calls mdelay() to busily wait, which is not necessary.
mdelay() can be replaced with msleep().
This is found by a static analysis tool named DCNS written by myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Subsystem:
- new helpers to add custom sysfs attributes
- struct rtc_task removal along with rtc_irq_register/rtc_irq_unregister
- rtc_irq_set_state and rtc_irq_set_freq are not exported anymore
Drivers:
- armada38x: reset after rtc power loss
- ds1307: now supports m41t11
- isl1208: now supports isl1219 and tamper detection
- pcf2127: internal SRAM support
-----BEGIN PGP SIGNATURE-----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=cAQ9
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"It is now possible to add custom sysfs attributes while avoiding a
possible race condition. Unused code has been removed resulting in a
nice reduction of the code base. And more drivers have been switched
to SPDX by their maintainers.
Summary:
Subsystem:
- new helpers to add custom sysfs attributes
- struct rtc_task removal along with rtc_irq_[un]register()
- rtc_irq_set_state and rtc_irq_set_freq are not exported anymore
Drivers:
- armada38x: reset after rtc power loss
- ds1307: now supports m41t11
- isl1208: now supports isl1219 and tamper detection
- pcf2127: internal SRAM support"
* tag 'rtc-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (34 commits)
rtc: ds1307: simplify hwmon config
rtc: s5m: Add SPDX license identifier
rtc: maxim: Add SPDX license identifiers
rtc: isl1219: add device tree documentation
rtc: isl1208: set ev-evienb bit from device tree
rtc: isl1208: Add "evdet" interrupt source for isl1219
rtc: isl1208: add support for isl1219 with tamper detection
rtc: sysfs: facilitate attribute add to rtc device
rtc: remove struct rtc_task
char: rtc: remove task handling
rtc: pcf85063: preserve control register value between stop and start
rtc: sh: remove unused variable rtc_dev
rtc: unexport rtc_irq_set_*
rtc: simplify rtc_irq_set_state/rtc_irq_set_freq
rtc: remove irq_task and irq_task_lock
rtc: remove rtc_irq_register/rtc_irq_unregister
rtc: sh: remove dead code
rtc: sa1100: don't set PIE frequency
rtc: ds1307: support m41t11 variant
rtc: ds1307: fix data pointer to m41t0
...
We don't have to define an extra config symbol, IS_REACHABLE does
what we need. And having this config symbol just to save the few
bytes of hwmon support on non-DS3231 chips isn't worth it IMO
(especially as the symbol is set per default).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add support to disable event in pull-up.
Signed-off-by: Denis Osterland <Denis.Osterland@diehl.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add support for "evdet" named interrupt source.
The check if i2c client irq matches evdet irq is needed
for the case that there is only one interrupt named "evdet".
In this case i2c client code handles this like an unnamed
interrupt souce and assigns the value.
Signed-off-by: Denis Osterland <Denis.Osterland@diehl.com>
Reviewed-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
We add support for the ISL1219 chip that got an integrated tamper
detection function. This patch implements the feature by adding
an additional timestamp0 file to sysfs device path.
This file contains seconds since epoch, if an event occurred,
or is empty, if none occurred.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Denis Osterland <Denis.Osterland@diehl.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patches addresses following problem:
rtc_allocate_device
devm_device_add_group <-- kernel oops / null pointer, because
sysfs entry does not yet exist
rtc_register_device
rc = devm_device_add_group
if (rc)
return rc; <-- forbidden to return error code
after device register
This patch adds rtc_add_group(s) functions.
The functions store the sum of attribute groups as device resource.
Signed-off-by: Denis Osterland <Denis.Osterland@diehl.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix a bug that caused the Control_1 register to get zeroed whenever the
RTC time is set. The problem occurred between stopping and starting the
RTC clock, wherein the return value of a successful I2C write function
would get written to the register.
Also update variables of the start and stop functions to be more
consistent with the rest of the driver.
Signed-off-by: Alvin Šipraga <alvin@airtame.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When building rtc-sh, rtc_dev isn't used in function __sh_rtc_periodic.
drivers/rtc/rtc-sh.c: In function ‘__sh_rtc_periodic’:
drivers/rtc/rtc-sh.c:146:21: warning: unused variable ‘rtc_dev’ [-Wunused-variable]
struct rtc_device *rtc_dev = rtc->rtc_dev;
^~~~~~~
Remove the declaration of rtc_dev to dispose the warning.
Fixes: ec623ff014 ("rtc: sh: remove dead code")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Since commit 80d4bb515b ("RTC: Cleanup rtc_class_ops->irq_set_state") and
commit 696160fec1 ("RTC: Cleanup rtc_class_ops->irq_set_freq()"),
sh_rtc_irq_set_state and sh_rtc_irq_set_freq are never called. Remove them
along with task handling.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
It doesn't make sense to set the PIE frequency from the driver. Let
userspace do its job.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The m41t11 variant is very similar to the already supported m41t00 and
m41t0, but it has also 56 bytes of NVRAM.
Add it to driver taking into account NVRAM section.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
data field points to m41t00, instead it should point to m41t0.
Driver works correctly because on both cases(m41t0 and m41t00) chip_desc
are equal.
Point to right enum m41t0 instead of m41t00.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
getnstimeofday64() is just a wrapper around the ktime accessor, so
we should use that directly.
I considered using ktime_get_boottime_ts64() (to avoid leap second
problems) or ktime_get_real_seconds() (to simplify the calculation,
but in the end concluded that the existing interface is probably
the most appropriate in this case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The offset needs to be added after reading the alarm value.
It also needs to be subtracted after the now < alarm test.
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Pointer 'name' is being assigned but is never used hence it is redundant
and can be removed.
Cleans up clang warning:
warning: variable 'name' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
