Add a host bridge driver for the Faraday Technology FPPCI100 host bridge,
used for Cortina Systems Gemini SoC (SL3516) PCI Host Bridge.
This code is inspired by the out-of-tree OpenWRT patch and then extensively
rewritten for device tree and using the modern helpers to cut down and
modernize the code to all new PCI frameworks. A driver exists in U-Boot as
well.
Tested on the ITian Square One SQ201 NAS with the following result in the
boot log (trimmed to relevant parts):
OF: PCI: host bridge /soc/pci@50000000 ranges:
OF: PCI: IO 0x50000000..0x500fffff -> 0x00000000
OF: PCI: MEM 0x58000000..0x5fffffff -> 0x58000000
ftpci100 50000000.pci: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [io 0x0000-0xfffff]
pci_bus 0000:00: root bus resource [mem 0x58000000-0x5fffffff]
ftpci100 50000000.pci:
DMA MEM1 BASE: 0x0000000000000000 -> 0x0000000007ffffff config 00070000
ftpci100 50000000.pci:
DMA MEM2 BASE: 0x0000000000000000 -> 0x0000000003ffffff config 00060000
ftpci100 50000000.pci:
DMA MEM3 BASE: 0x0000000000000000 -> 0x0000000003ffffff config 00060000
PCI: bus0: Fast back to back transfers disabled
pci 0000:00:00.0: of_irq_parse_pci() failed with rc=-22
pci 0000:00:0c.0: BAR 0: assigned [mem 0x58000000-0x58007fff]
pci 0000:00:09.2: BAR 0: assigned [mem 0x58008000-0x580080ff]
pci 0000:00:09.0: BAR 4: assigned [io 0x1000-0x101f]
pci 0000:00:09.1: BAR 4: assigned [io 0x1020-0x103f]
pci 0000:00:09.0: enabling device (0140 -> 0141)
pci 0000:00:09.0: HCRESET not completed yet!
pci 0000:00:09.1: enabling device (0140 -> 0141)
pci 0000:00:09.1: HCRESET not completed yet!
pci 0000:00:09.2: enabling device (0140 -> 0142)
rt61pci 0000:00:0c.0: enabling device (0140 -> 0142)
ieee80211 phy0: rt2x00_set_chip: Info - Chipset detected -
rt: 2561, rf: 0003, rev: 000c
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-pci: EHCI PCI platform driver
ehci-pci 0000:00:09.2: EHCI Host Controller
ehci-pci 0000:00:09.2: new USB bus registered, assigned bus number 1
ehci-pci 0000:00:09.2: irq 125, io mem 0x58008000
ehci-pci 0000:00:09.2: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:09.0: UHCI Host Controller
uhci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:09.0: HCRESET not completed yet!
uhci_hcd 0000:00:09.0: irq 123, io base 0x00001000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
uhci_hcd 0000:00:09.1: UHCI Host Controller
uhci_hcd 0000:00:09.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:09.1: HCRESET not completed yet!
uhci_hcd 0000:00:09.1: irq 124, io base 0x00001020
hub 3-0:1.0: USB hub found
hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19)
scsi 0:0:0:0: Direct-Access USB Flash Disk 1.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 7900336 512-byte logical blocks: (4.04 GB/3.77 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] No Caching mode page found
sd 0:0:0:0: [sda] Assuming drive cache: write through
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI removable disk
ieee80211 phy0: rt2x00lib_request_firmware: Info -
Loading firmware file 'rt2561s.bin'
ieee80211 phy0: rt2x00lib_request_firmware: Info -
Firmware detected - version: 0.8
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
$ lspci
00:00.0 Class 0600: 159b:4321
00:09.2 Class 0c03: 1106:3104
00:09.0 Class 0c03: 1106:3038
00:09.1 Class 0c03: 1106:3038
00:0c.0 Class 0280: 1814:0301
$ cat /proc/interrupts
CPU0
123: 0 PCI 0 Edge uhci_hcd:usb2
124: 0 PCI 1 Edge uhci_hcd:usb3
125: 159 PCI 2 Edge ehci_hcd:usb1
126: 1082 PCI 3 Edge rt61pci
$ cat /proc/iomem
50000000-500000ff : /soc/pci@50000000
58000000-5fffffff : Gemini PCI MEM
58000000-58007fff : 0000:00:0c.0
58000000-58007fff : 0000:00:0c.0
58008000-580080ff : 0000:00:09.2
58008000-580080ff : ehci_hcd
The EHCI USB hub works fine; I can mount and manage files and the IRQs just
keep ticking up. I can issue iwlist wlan0 scanning and see all the WLANs
here. I don't have wpa_supplicant so have not tried connecting to them.
[bhelgaas: fold in %pap change from Arnd Bergmann <arnd@arndb.de>]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Janos Laube <janos.dev@gmail.com>
CC: Paulius Zaleckas <paulius.zaleckas@gmail.com>
CC: Hans Ulli Kroll <ulli.kroll@googlemail.com>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: Feng-Hsin Chiang <john453@faraday-tech.com>
CC: Greentime Hu <green.hu@gmail.com>
Group all the PCI drivers that use DesignWare core in dwc directory.
dwc IP is capable of operating in both host mode and device mode and
keeping it inside the *host* directory is misleading.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Minghuan Lian <minghuan.Lian@freescale.com>
Cc: Mingkai Hu <mingkai.hu@freescale.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Niklas Cassel <niklas.cassel@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Add Makefile comments to explain the Kconfig and build strategy for ARM64
drivers that work around not-quite-ECAM issues. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCIe controllers in X-Gene SoCs are not ECAM compliant: software needs to
configure additional controller's register to address device at
bus:dev:function.
Add a quirk to discover controller MMIO register space and configure
controller registers to select and address the target secondary device.
The quirk will only be applied for X-Gene PCIe MCFG table with
OEM revison 1, 2, 3 or 4 (PCIe controller v1 and v2 on X-Gene SoCs).
Tested-by: Jon Masters <jcm@redhat.com>
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ThunderX pass1.x requires to emulate the EA headers for on-chip devices
hence it has to use custom pci_thunder_ecam_ops for accessing PCI config
space (pci-thunder-ecam.c). Add new entries to MCFG quirk array where it
can be applied while probing ACPI based PCI host controller.
ThunderX pass1.x is using the same way for accessing off-chip devices
(so-called PEM) as silicon pass-2.x so we need to add PEM quirk entries
too.
Quirk is considered for ThunderX silicon pass1.x only which is identified
via MCFG revision 2.
ThunderX pass 1.x requires the following accessors:
NUMA node 0 PCI segments 0- 3: pci_thunder_ecam_ops (MCFG quirk)
NUMA node 0 PCI segments 4- 9: thunder_pem_ecam_ops (MCFG quirk)
NUMA node 1 PCI segments 10-13: pci_thunder_ecam_ops (MCFG quirk)
NUMA node 1 PCI segments 14-19: thunder_pem_ecam_ops (MCFG quirk)
[bhelgaas: change Makefile/ifdefs so quirk doesn't depend on
CONFIG_PCI_HOST_THUNDER_ECAM]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ThunderX PCIe controller to off-chip devices (so-called PEM) is not fully
compliant with ECAM standard. It uses non-standard configuration space
accessors (see thunder_pem_ecam_ops) and custom configuration space
granulation (see bus_shift = 24). In order to access configuration space
and probe PEM as ACPI-based PCI host controller we need to add MCFG quirk
infrastructure. This involves:
1. A new thunder_pem_acpi_init() init function to locate PEM-specific
register ranges using ACPI.
2. Export PEM thunder_pem_ecam_ops structure so it is visible to MCFG quirk
code.
3. New quirk entries for each PEM segment. Each contains platform IDs,
mentioned thunder_pem_ecam_ops and CFG resources.
Quirk is considered for ThunderX silicon pass2.x only which is identified
via MCFG revision 1.
ThunderX pass 2.x requires the following accessors:
NUMA Node 0 PCI segments 0- 3: pci_generic_ecam_ops (ECAM-compliant)
NUMA Node 0 PCI segments 4- 9: thunder_pem_ecam_ops (MCFG quirk)
NUMA Node 1 PCI segments 10-13: pci_generic_ecam_ops (ECAM-compliant)
NUMA Node 1 PCI segments 14-19: thunder_pem_ecam_ops (MCFG quirk)
[bhelgaas: adapt to use acpi_get_rc_resources(), update Makefile/ifdefs so
quirk doesn't depend on CONFIG_PCI_HOST_THUNDER_PEM]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe controller in Hip05/Hip06/Hip07 SoCs is not completely
ECAM-compliant. It is non-ECAM only for the RC bus config space; for any
other bus underneath the root bus it does support ECAM access.
Add specific quirks for PCI config space accessors. This involves:
1. New initialization call hisi_pcie_init() to obtain RC base
addresses from PNP0C02 at the root of the ACPI namespace (under \_SB).
2. New entry in common quirk array.
[bhelgaas: move to pcie-hisi.c and change Makefile/ifdefs so quirk doesn't
depend on CONFIG_PCI_HISI]
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/host-vmd:
x86/PCI: VMD: Move VMD driver to drivers/pci/host
x86/PCI: VMD: Synchronize with RCU freeing MSI IRQ descs
x86/PCI: VMD: Eliminate index member from IRQ list
x86/PCI: VMD: Eliminate vmd_vector member from list type
x86/PCI: VMD: Convert to use pci_alloc_irq_vectors() API
x86/PCI: VMD: Allocate IRQ lists with correct MSI-X count
PCI: Use positive flags in pci_alloc_irq_vectors()
PCI: Update "pci=resource_alignment" documentation
Conflicts:
drivers/pci/host/Kconfig
drivers/pci/host/Makefile
Move the driver source and Kconfig to the PCI host bridge drivers directory
and move the config option to a more appropriate sub-menu instead of
occupying the top-level location.
Update the Kconfig option with the X86_64 dependency that was implicitly
included from the previous location, and add information about the module
name when built as a loadable module.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Jon Derrick <jonathan.derrick@intel.com>
Add support for the Rockchip PCIe controller found on RK3399 SoC platform.
[bhelgaas: fold in Brian's rockchip_pcie_client_irq_handler() OR fix, other
fixes and cleanups from Guenter Roeck <linux@roeck-us.net> and me,
uninitialized variable fix from Arnd Bergmann <arnd@arndb.de>]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
* pci/host-aardvark:
arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700
PCI: aardvark: Add Aardvark PCI host controller driver
dt-bindings: add DT binding for the Aardvark PCIe controller
* pci/host-altera:
PCI: altera: Poll for link up status after retraining the link
PCI: altera: Check link status before retrain link
PCI: altera: Reorder read/write functions
* pci/host-dra7xx:
PCI: dra7xx: Fix return value in case of error
* pci/host-hv:
PCI: hv: Fix interrupt cleanup path
PCI: hv: Handle all pending messages in hv_pci_onchannelcallback()
PCI: hv: Don't leak buffer in hv_pci_onchannelcallback()
* pci/host-vmd:
x86/PCI: VMD: Separate MSI and MSI-X vector sharing
x86/PCI: VMD: Use x86_vector_domain as parent domain
x86/PCI: VMD: Use lock save/restore in interrupt enable path
x86/PCI: VMD: Initialize list item in IRQ disable
x86/PCI: VMD: Select device dma ops to override
* pci/host-xilinx:
PCI: xilinx: Fix return value in case of error
Manually apply changes from pci/demodularize-hosts and
pci/host-request-windows to drivers/pci/host/pci-aardvark.c
Add a driver for the Aardvark PCIe controller used on the Marvell Armada
3700 ARM64 SoC.
Based on work done by Hezi Shahmoon <hezi.shahmoon@marvell.com> and Marcin
Wojtas <mw@semihalf.com>.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Axis ARTPEC-6 SoC integrates a PCIe controller from Synopsys. Add a
new driver that provides the small glue needed to use the existing
DesignWare driver to make it work on the Axis ARTPEC-6 SoC.
[bhelgaas: return errors directly without gotos, fold in section mismatch
fix]
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Enumeration
Refine PCI support check in pcibios_init() (Adrian-Ken Rueegsegger)
Provide common functions for ECAM mapping (Jayachandran C)
Allow all PCIe services on non-ACPI host bridges (Jon Derrick)
Remove return values from pcie_port_platform_notify() and relatives (Jon Derrick)
Widen portdrv service type from 4 bits to 8 bits (Keith Busch)
Add Downstream Port Containment portdrv service type (Keith Busch)
Add Downstream Port Containment driver (Keith Busch)
Resource management
Identify Enhanced Allocation (EA) BAR Equivalent resources in sysfs (Alex Williamson)
Supply CPU physical address (not bus address) to iomem_is_exclusive() (Bjorn Helgaas)
alpha: Call iomem_is_exclusive() for IORESOURCE_MEM, but not IORESOURCE_IO (Bjorn Helgaas)
Mark Broadwell-EP Home Agent 1 as having non-compliant BARs (Prarit Bhargava)
Disable all BAR sizing for devices with non-compliant BARs (Prarit Bhargava)
Move PCI I/O space management from OF to PCI core code (Tomasz Nowicki)
PCI device hotplug
acpiphp_ibm: Avoid uninitialized variable reference (Dan Carpenter)
Use cached copy of PCI_EXP_SLTCAP_HPC bit (Lukas Wunner)
Virtualization
Mark Intel i40e NIC INTx masking as broken (Alex Williamson)
Reverse standard ACS vs device-specific ACS enabling (Alex Williamson)
Work around Intel Sunrise Point PCH incorrect ACS capability (Alex Williamson)
IOMMU
Add pci_add_dma_alias() to abstract implementation (Bjorn Helgaas)
Move informational printk to pci_add_dma_alias() (Bjorn Helgaas)
Add support for multiple DMA aliases (Jacek Lawrynowicz)
Add DMA alias quirk for mic_x200_dma (Jacek Lawrynowicz)
Thunderbolt
Fix double free of drom buffer (Andreas Noever)
Add Intel Thunderbolt device IDs (Lukas Wunner)
Fix typos and magic number (Lukas Wunner)
Support 1st gen Light Ridge controller (Lukas Wunner)
Generic host bridge driver
Use generic ECAM API (Jayachandran C)
Cavium ThunderX host bridge driver
Don't clobber read-only bits in bridge config registers (David Daney)
Use generic ECAM API (Jayachandran C)
Freescale i.MX6 host bridge driver
Use enum instead of bool for variant indicator (Andrey Smirnov)
Implement reset sequence for i.MX6+ (Andrey Smirnov)
Factor out ref clock enable (Bjorn Helgaas)
Add initial imx6sx support (Christoph Fritz)
Add reset-gpio-active-high boolean property to DT (Petr Štetiar)
Add DT property for link gen, default to Gen1 (Tim Harvey)
dts: Specify imx6qp version of PCIe core (Andrey Smirnov)
dts: Fix PCIe reset GPIO polarity on Toradex Apalis Ixora (Petr Štetiar)
Marvell Armada host bridge driver
add DT binding for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
Add driver for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
Marvell MVEBU host bridge driver
Constify mvebu_pcie_pm_ops structure (Jisheng Zhang)
Use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS for mvebu_pcie_pm_ops (Jisheng Zhang)
Microsoft Hyper-V host bridge driver
Report resources release after stopping the bus (Vitaly Kuznetsov)
Add explicit barriers to config space access (Vitaly Kuznetsov)
Renesas R-Car host bridge driver
Select PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
Synopsys DesignWare host bridge driver
Remove incorrect RC memory base/limit configuration (Gabriele Paoloni)
Move Root Complex setup code to dw_pcie_setup_rc() (Jisheng Zhang)
TI Keystone host bridge driver
Add error IRQ handler (Murali Karicheri)
Remove unnecessary goto statement (Murali Karicheri)
Miscellaneous
Fix spelling errors (Colin Ian King)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=68Iz
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Refine PCI support check in pcibios_init() (Adrian-Ken Rueegsegger)
- Provide common functions for ECAM mapping (Jayachandran C)
- Allow all PCIe services on non-ACPI host bridges (Jon Derrick)
- Remove return values from pcie_port_platform_notify() and relatives (Jon Derrick)
- Widen portdrv service type from 4 bits to 8 bits (Keith Busch)
- Add Downstream Port Containment portdrv service type (Keith Busch)
- Add Downstream Port Containment driver (Keith Busch)
Resource management:
- Identify Enhanced Allocation (EA) BAR Equivalent resources in sysfs (Alex Williamson)
- Supply CPU physical address (not bus address) to iomem_is_exclusive() (Bjorn Helgaas)
- alpha: Call iomem_is_exclusive() for IORESOURCE_MEM, but not IORESOURCE_IO (Bjorn Helgaas)
- Mark Broadwell-EP Home Agent 1 as having non-compliant BARs (Prarit Bhargava)
- Disable all BAR sizing for devices with non-compliant BARs (Prarit Bhargava)
- Move PCI I/O space management from OF to PCI core code (Tomasz Nowicki)
PCI device hotplug:
- acpiphp_ibm: Avoid uninitialized variable reference (Dan Carpenter)
- Use cached copy of PCI_EXP_SLTCAP_HPC bit (Lukas Wunner)
Virtualization:
- Mark Intel i40e NIC INTx masking as broken (Alex Williamson)
- Reverse standard ACS vs device-specific ACS enabling (Alex Williamson)
- Work around Intel Sunrise Point PCH incorrect ACS capability (Alex Williamson)
IOMMU:
- Add pci_add_dma_alias() to abstract implementation (Bjorn Helgaas)
- Move informational printk to pci_add_dma_alias() (Bjorn Helgaas)
- Add support for multiple DMA aliases (Jacek Lawrynowicz)
- Add DMA alias quirk for mic_x200_dma (Jacek Lawrynowicz)
Thunderbolt:
- Fix double free of drom buffer (Andreas Noever)
- Add Intel Thunderbolt device IDs (Lukas Wunner)
- Fix typos and magic number (Lukas Wunner)
- Support 1st gen Light Ridge controller (Lukas Wunner)
Generic host bridge driver:
- Use generic ECAM API (Jayachandran C)
Cavium ThunderX host bridge driver:
- Don't clobber read-only bits in bridge config registers (David Daney)
- Use generic ECAM API (Jayachandran C)
Freescale i.MX6 host bridge driver:
- Use enum instead of bool for variant indicator (Andrey Smirnov)
- Implement reset sequence for i.MX6+ (Andrey Smirnov)
- Factor out ref clock enable (Bjorn Helgaas)
- Add initial imx6sx support (Christoph Fritz)
- Add reset-gpio-active-high boolean property to DT (Petr Štetiar)
- Add DT property for link gen, default to Gen1 (Tim Harvey)
- dts: Specify imx6qp version of PCIe core (Andrey Smirnov)
- dts: Fix PCIe reset GPIO polarity on Toradex Apalis Ixora (Petr Štetiar)
Marvell Armada host bridge driver:
- add DT binding for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
- Add driver for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
Marvell MVEBU host bridge driver:
- Constify mvebu_pcie_pm_ops structure (Jisheng Zhang)
- Use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS for mvebu_pcie_pm_ops (Jisheng Zhang)
Microsoft Hyper-V host bridge driver:
- Report resources release after stopping the bus (Vitaly Kuznetsov)
- Add explicit barriers to config space access (Vitaly Kuznetsov)
Renesas R-Car host bridge driver:
- Select PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
Synopsys DesignWare host bridge driver:
- Remove incorrect RC memory base/limit configuration (Gabriele Paoloni)
- Move Root Complex setup code to dw_pcie_setup_rc() (Jisheng Zhang)
TI Keystone host bridge driver:
- Add error IRQ handler (Murali Karicheri)
- Remove unnecessary goto statement (Murali Karicheri)
Miscellaneous:
- Fix spelling errors (Colin Ian King)"
* tag 'pci-v4.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (48 commits)
PCI: Disable all BAR sizing for devices with non-compliant BARs
x86/PCI: Mark Broadwell-EP Home Agent 1 as having non-compliant BARs
PCI: Identify Enhanced Allocation (EA) BAR Equivalent resources in sysfs
PCI, of: Move PCI I/O space management to PCI core code
PCI: generic, thunder: Use generic ECAM API
PCI: Provide common functions for ECAM mapping
PCI: hv: Add explicit barriers to config space access
PCI: Use cached copy of PCI_EXP_SLTCAP_HPC bit
PCI: Add Downstream Port Containment driver
PCI: Add Downstream Port Containment portdrv service type
PCI: Widen portdrv service type from 4 bits to 8 bits
PCI: designware: Remove incorrect RC memory base/limit configuration
PCI: hv: Report resources release after stopping the bus
ARM: dts: imx6qp: Specify imx6qp version of PCIe core
PCI: imx6: Implement reset sequence for i.MX6+
PCI: imx6: Use enum instead of bool for variant indicator
PCI: thunder: Don't clobber read-only bits in bridge config registers
thunderbolt: Fix double free of drom buffer
PCI: rcar: Select PCI_MSI_IRQ_DOMAIN
PCI: armada: Add driver for Marvell Armada 7K/8K PCIe controller
...
The Marvell Armada 7K/8K SoCs integrate a PCIe controller from Synopsys.
Add a new driver that provides the small glue needed to use the existing
Designware driver to make it work on Marvell Armada 7K/8K SoCs.
The MSI support will be enabled at a later point.
[bhelgaas: use dev_dbg(), dw_pcie_wait_for_link()]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It appears that Gen2 is a misnomer for the R-Car PCIE driver
which also supports Gen 1 and Gen 3 SoCs. Accordingly, drop Gen 2
from the help text and Kconfig symbol.
Also, re-arange the Kconfig symbol name to use PCIE as the prefix.
This appears to be in keeping with other PCIE Kconfig symbols.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
* pci/host-hv:
PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs
PCI: Look up IRQ domain by fwnode_handle
PCI: Add fwnode_handle to x86 pci_sysdata
* pci/host-designware:
PCI: designware: Add driver for prototyping kits based on ARC SDP
PCI: designware: Add default link up check if sub-driver doesn't override
PCI: designware: Add generic dw_pcie_wait_for_link()
ARC: Add PCI support
The cavium,pci-thunder-ecam devices are exactly ECAM-based PCI root
complexes. These root complexes (loosely referred to as ECAM units in the
hardware manuals) are used to access the Thunder on-chip devices. They
are special in that all the BARs on devices behind these root complexes are
at fixed addresses.
Add a driver for these devices that synthesizes Enhanced Allocation (EA)
capability entries for each BAR.
Since this EA synthesis is needed for exactly two chip models, we can hard-
code some assumptions about the device topology and the layout of the
config space of specific DEVFNs in the driver.
[bhelgaas: changelog, whitespace]
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
The root complexes used to access off-chip PCIe devices (called PEM units
in the hardware manuals) on some Cavium ThunderX processors require quirky
access methods for the config space of the PCIe bridge.
Add a driver to provide these config space accessor functions. Use the
pci-host-common code to configure the PCI machinery.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Move pci_host_common_probe() and associated functions to pci-host-common.c,
where it can be shared with other drivers. Make it public (not static)
and update Kconfig and Makefile to build it. No functional change
intended.
[bhelgaas: split into separate patch, changelog]
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Will Deacon <will.deacon@arm.com>
Add a new driver which exposes a root PCI bus whenever a PCI Express device
is passed through to a guest VM under Hyper-V. The device can be single-
or multi-function. The interrupts for the devices are managed by an IRQ
domain, implemented within the driver.
[bhelgaas: fold in race condition fix (http://lkml.kernel.org/r/1456340196-13717-1-git-send-email-jakeo@microsoft.com)]
Signed-off-by: Jake Oshins <jakeo@microsoft.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add PCIe MSI support for both PAXB and PAXC interfaces on all iProc-based
platforms.
The iProc PCIe MSI support deploys an event queue-based implementation.
Each event queue is serviced by a GIC interrupt and can support up to 64
MSI vectors. Host memory is allocated for the event queues, and each event
queue consists of 64 word-sized entries. MSI data is written to the lower
16-bit of each entry, whereas the upper 16-bit of the entry is reserved for
the controller for internal processing.
Each event queue is tracked by a head pointer and tail pointer. Head
pointer indicates the next entry in the event queue to be processed by
the driver and is updated by the driver after processing is done.
The controller uses the tail pointer as the next MSI data insertion
point. The controller ensures MSI data is flushed to host memory before
updating the tail pointer and then triggering the interrupt.
MSI IRQ affinity is supported by evenly distributing the interrupts to each
CPU core. MSI vector is moved from one GIC interrupt to another in order
to steer to the target CPU.
Therefore, the actual number of supported MSI vectors is:
M * 64 / N
where M denotes the number of GIC interrupts (event queues), and N denotes
the number of CPU cores.
This iProc event queue-based MSI support should not be used with newer
platforms with integrated MSI support in the GIC (e.g., giv2m or
gicv3-its).
[bhelgaas: fold in Kconfig fixes from Arnd Bergmann <arnd@arndb.de>]
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Vikram Prakash <vikramp@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
The PCIe driver reuses the Designware common code for host and MSI
initialization, and also programs the Qualcomm application specific
registers.
[bhelgaas: remove COMPILE_TEST Kconfig dependency]
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add Altera PCIe MSI driver. This soft IP supports a configurable number of
vectors, which is a DTS parameter.
[bhelgaas: Kconfig depend on PCIE_ALTERA, typos, whitespace]
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Add the Altera PCIe host controller driver.
[bhelgaas: whitespace, fold in DT and maintainer updates, OF_PCI
dependency from Arnd]
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <robh@kernel.org> (DT binding)
APM X-Gene v1 SoC supports its own implementation of MSI, which is not
compliant to GIC V2M specification for MSI Termination.
There is a single MSI block in X-Gene v1 SOC which serves all 5 PCIe ports.
This MSI block supports 2048 MSI termination ports coalesced into 16
physical HW IRQ lines and shared across all 5 PCIe ports.
As there are only 16 HW IRQs to serve 2048 MSI vectors, to support
set_affinity correctly for each MSI vectors, the 16 HW IRQs are statically
allocated to 8 X-Gene v1 cores (2 HW IRQs for each cores). To steer MSI
interrupt to target CPU, MSI vector is moved around these HW IRQs lines.
With this approach, the total MSI vectors this driver supports is reduced
to 256.
[bhelgaas: squash doc, driver, maintainer update]
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
This driver adds support for the PCIe 2.0 controller found on the BCMA bus.
This controller can be found on (mostly) all Broadcom BCM470X / BCM5301X
ARM SoCs.
The driver found in the Broadcom SDK does some more stuff, like setting up
some DMA memory areas, chaining MPS and MRRS to 512 and also some PHY
changes like "improving" the PCIe jitter and doing some special
initialization for the 3rd PCIe port.
This was tested on a bcm4708 board with 2 PCIe ports and wireless cards
connected to them.
PCI_DOMAINS is needed by this driver, because normally there is more than
one PCIe controller and without PCI_DOMAINS only the first controller gets
registered. This controller gets 6 IRQs; the last one is trigged by all
IRQ events.
[bhelgaas: fix "GPLv2" MODULE_LICENSE typo]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Ray Jui <rjui@broadcom.com.com>
Add support for the Broadcom iProc PCIe controller.
pcie-iproc.c is the common core driver, and a front-end bus interface needs
to be added to support different bus interfaces.
pcie-iproc-platform.c contains the support for the platform bus interface.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This converts the Versatile PCI host code to a platform driver using the
commom DT parsing and setup. The driver uses only an empty ARM
pci_sys_data struct and does not use pci_common_init_dev init function.
The old host code will be removed in a subsequent commit when Versatile is
completely converted to DT.
I've tested this on QEMU with the sym53c8xx driver in both i/o and memory
mapped modes.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: Peter Maydell <peter.maydell@linaro.org>
Add the AppliedMicro X-Gene SOC PCIe host controller driver. The X-Gene
PCIe controller supports up to 8 lanes and GEN3 speed. The X-Gene SOC
supports up to 5 PCIe ports.
[bhelgaas: folded in MAINTAINERS and bindings updates]
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Dann Frazier <dann.frazier@canonical.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com> (driver)
* pci/misc:
PCI/AER: Make <linux/aer.h> standalone includable
PCI: Remove unnecessary variable in pci_add_dynid()
* pci/pm:
PCI/PM: Allow PCI devices to be put into D3cold during system suspend
PCI/PM: Drop unused runtime PM support code for PCIe ports
* pci/host-designware:
PCI: designware: Check private_data validity in single place
PCI: designware: Remove pci_assign_unassigned_resources() from dw_pcie_host_init()
PCI: designware: Use pci_create_root_bus() instead of pci_scan_root_bus()
PCI: designware: Parse bus-range property from devicetree
PCI: designware: Add support for v3.65 hardware
* pci/host-imx6:
PCI: imx6: Probe in module_init(), not fs_initcall()
PCI: designware: Remove pci_assign_unassigned_resources() from dw_pcie_host_init()
PCI: designware: Use pci_create_root_bus() instead of pci_scan_root_bus()
PCI: designware: Parse bus-range property from devicetree
PCI: imx6: Put LTSSM in "Detect" state before disabling it
MAINTAINERS: Add Lucas Stach as co-maintainer for i.MX6 PCI driver
PCI: designware: Add support for v3.65 hardware
* pci/host-keystone:
PCI: keystone: Add TI Keystone PCIe driver
PCI: designware: Add support for v3.65 hardware
* pci/host-tegra:
PCI: tegra: Implement a proper resource hierarchy
PCI: tegra: Add missing cleanup in error path and tegra_msi_teardown_irq()
resources: Add device-managed request/release_resource()
* pci/host-xilinx:
PCI: xilinx: Add Xilinx AXI PCIe Host Bridge IP driver
Conflicts:
drivers/pci/host/Kconfig
drivers/pci/host/Makefile
The Keystone PCIe controller is based on v3.65 version of the Designware
h/w. Main differences are:
1. No ATU support
2. Legacy and MSI IRQ functions are implemented in application register
space
3. MSI interrupts are multiplexed over 8 IRQ lines to the Host side.
All of the application register space handing code is organized into
pci-keystone-dw.c and the functions are called from pci-keystone.c to
implement PCI controller driver. Also add necessary DT documentation and
update the MAINTAINERS file for the driver.
[bhelgaas: spelling and whitespace fixes]
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Mohit Kumar <mohit.kumar@st.com>
CC: Pratyush Anand <pratyush.anand@st.com>
CC: Jingoo Han <jg1.han@samsung.com>
CC: Richard Zhu <r65037@freescale.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Marek Vasut <marex@denx.de>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
CC: Randy Dunlap <rdunlap@infradead.org>
CC: Grant Likely <grant.likely@linaro.org>
Add support for PCIe controller in DRA7xx. This driver re-uses the
designware core code that is already present in kernel.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
ARM based ST Microelectronics's SPEAr1310 and SPEAr1340 SOCs have onchip
designware PCIe controller. To make that usable, this patch adds a wrapper
driver based on existing designware driver.
Adds bindings for this new driver and update MAINTAINERS as well.
Cc: linux-pci@vger.kernel.org
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
[viresh: fixed logs/cclist/checkpatch warnings, broken into smaller patches]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Add support for a generic PCI host controller, such as a
firmware-initialised device with static windows or an emulation by
something such as kvmtool.
The controller itself has no configuration registers and has its address
spaces described entirely by the device-tree (using the bindings from
ePAPR). Both CAM and ECAM are supported for Config Space accesses.
Add corresponding documentation for the DT binding.
[bhelgaas: currently uses the ARM-specific pci_common_init_dev() interface]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
This PCIe Host driver currently does not support MSI, so cards fall back to
INTx interrupts.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
