We are going to track per-extent information, so it'll be necessary to
distinguish between inode infos and extent infos. Rename fscrypt_info
to fscrypt_inode_info, adjusting any lines that now exceed 80
characters.
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
[ebiggers: rebased onto fscrypt tree, renamed fscrypt_get_info(),
adjusted two comments, and fixed some lines over 80 characters]
Link: https://lore.kernel.org/r/20231005025757.33521-1-ebiggers@kernel.org
Reviewed-by: Neal Gompa <neal@gompa.dev>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Until now, fscrypt has always used the filesystem block size as the
granularity of file contents encryption. Two scenarios have come up
where a sub-block granularity of contents encryption would be useful:
1. Inline crypto hardware that only supports a crypto data unit size
that is less than the filesystem block size.
2. Support for direct I/O at a granularity less than the filesystem
block size, for example at the block device's logical block size in
order to match the traditional direct I/O alignment requirement.
(1) first came up with older eMMC inline crypto hardware that only
supports a crypto data unit size of 512 bytes. That specific case
ultimately went away because all systems with that hardware continued
using out of tree code and never actually upgraded to the upstream
inline crypto framework. But, now it's coming back in a new way: some
current UFS controllers only support a data unit size of 4096 bytes, and
there is a proposal to increase the filesystem block size to 16K.
(2) was discussed as a "nice to have" feature, though not essential,
when support for direct I/O on encrypted files was being upstreamed.
Still, the fact that this feature has come up several times does suggest
it would be wise to have available. Therefore, this patch implements it
by using one of the reserved bytes in fscrypt_policy_v2 to allow users
to select a sub-block data unit size. Supported data unit sizes are
powers of 2 between 512 and the filesystem block size, inclusively.
Support is implemented for both the FS-layer and inline crypto cases.
This patch focuses on the basic support for sub-block data units. Some
things are out of scope for this patch but may be addressed later:
- Supporting sub-block data units in combination with
FSCRYPT_POLICY_FLAG_IV_INO_LBLK_64, in most cases. Unfortunately this
combination usually causes data unit indices to exceed 32 bits, and
thus fscrypt_supported_policy() correctly disallows it. The users who
potentially need this combination are using f2fs. To support it, f2fs
would need to provide an option to slightly reduce its max file size.
- Supporting sub-block data units in combination with
FSCRYPT_POLICY_FLAG_IV_INO_LBLK_32. This has the same problem
described above, but also it will need special code to make DUN
wraparound still happen on a FS block boundary.
- Supporting use case (2) mentioned above. The encrypted direct I/O
code will need to stop requiring and assuming FS block alignment.
This won't be hard, but it belongs in a separate patch.
- Supporting this feature on filesystems other than ext4 and f2fs.
(Filesystems declare support for it via their fscrypt_operations.)
On UBIFS, sub-block data units don't make sense because UBIFS encrypts
variable-length blocks as a result of compression. CephFS could
support it, but a bit more work would be needed to make the
fscrypt_*_block_inplace functions play nicely with sub-block data
units. I don't think there's a use case for this on CephFS anyway.
Link: https://lore.kernel.org/r/20230925055451.59499-6-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Replace FS_CFLG_OWN_PAGES with a bit flag 'needs_bounce_pages' which has
the opposite meaning. I.e., filesystems now opt into the bounce page
pool instead of opt out. Make fscrypt_alloc_bounce_page() check that
the bounce page pool has been initialized.
I believe the opt-in makes more sense, since nothing else in
fscrypt_operations is opt-out, and these days filesystems can choose to
use blk-crypto which doesn't need the fscrypt bounce page pool. Also, I
happen to be planning to add two more flags, and I wanted to fix the
"FS_CFLG_" name anyway as it wasn't prefixed with "FSCRYPT_".
Link: https://lore.kernel.org/r/20230925055451.59499-3-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
fscrypt_initialize() is a "one-time init" function that is called
whenever the key is set up for any inode on any filesystem. Make it
implement "one-time init" more efficiently by not taking a global mutex
in the "already initialized case" and doing fewer pointer dereferences.
Link: https://lore.kernel.org/r/20230406181245.36091-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Try to make the filesystem-level decryption functions in fs/crypto/
aware of large folios. This includes making fscrypt_decrypt_bio()
support the case where the bio contains large folios, and making
fscrypt_decrypt_pagecache_blocks() take a folio instead of a page.
There's no way to actually test this with large folios yet, but I've
tested that this doesn't cause any regressions.
Note that this patch just handles *decryption*, not encryption which
will be a little more difficult.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Link: https://lore.kernel.org/r/20230127224202.355629-1-ebiggers@kernel.org
FS_CRYPTO_BLOCK_SIZE is neither the filesystem block size nor the
granularity of encryption. Rather, it defines two logically separate
constraints that both arise from the block size of the AES cipher:
- The alignment required for the lengths of file contents blocks
- The minimum input/output length for the filenames encryption modes
Since there are way too many things called the "block size", and the
connection with the AES block size is not easily understood, split
FS_CRYPTO_BLOCK_SIZE into two constants FSCRYPT_CONTENTS_ALIGNMENT and
FSCRYPT_FNAME_MIN_MSG_LEN that more clearly describe what they are.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20220405010914.18519-1-ebiggers@kernel.org
All filesystems have now been converted to use ->readahead, so
remove the ->readpages operation and fix all the comments that
used to refer to it.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Encrypted files traditionally haven't supported DIO, due to the need to
encrypt/decrypt the data. However, when the encryption is implemented
using inline encryption (blk-crypto) instead of the traditional
filesystem-layer encryption, it is straightforward to support DIO.
In preparation for supporting this, add the following functions:
- fscrypt_dio_supported() checks whether a DIO request is supported as
far as encryption is concerned. Encrypted files will only support DIO
when inline encryption is used and the I/O request is properly
aligned; this function checks these preconditions.
- fscrypt_limit_io_blocks() limits the length of a bio to avoid crossing
a place in the file that a bio with an encryption context cannot
cross due to a DUN discontiguity. This function is needed by
filesystems that use the iomap DIO implementation (which operates
directly on logical ranges, so it won't use fscrypt_mergeable_bio())
and that support FSCRYPT_POLICY_FLAG_IV_INO_LBLK_32.
Co-developed-by: Satya Tangirala <satyat@google.com>
Signed-off-by: Satya Tangirala <satyat@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220128233940.79464-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Now that a fscrypt_info may be set up for inodes that are currently
being created and haven't yet had an inode number assigned, avoid
logging confusing messages about "inode 0".
Acked-by: Jeff Layton <jlayton@kernel.org>
Link: https://lore.kernel.org/r/20200917041136.178600-7-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
The name "FS_KEY_DERIVATION_NONCE_SIZE" is a bit outdated since due to
the addition of FSCRYPT_POLICY_FLAG_DIRECT_KEY, the file nonce may now
be used as a tweak instead of for key derivation. Also, we're now
prefixing the fscrypt constants with "FSCRYPT_" instead of "FS_".
Therefore, rename this constant to FSCRYPT_FILE_NONCE_SIZE.
Link: https://lore.kernel.org/r/20200708215722.147154-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Add support for inline encryption to fs/crypto/. With "inline
encryption", the block layer handles the decryption/encryption as part
of the bio, instead of the filesystem doing the crypto itself via
Linux's crypto API. This model is needed in order to take advantage of
the inline encryption hardware present on most modern mobile SoCs.
To use inline encryption, the filesystem needs to be mounted with
'-o inlinecrypt'. Blk-crypto will then be used instead of the traditional
filesystem-layer crypto whenever possible to encrypt the contents
of any encrypted files in that filesystem. Fscrypt still provides the key
and IV to use, and the actual ciphertext on-disk is still the same;
therefore it's testable using the existing fscrypt ciphertext verification
tests.
Note that since blk-crypto has a fallback to Linux's crypto API, and
also supports all the encryption modes currently supported by fscrypt,
this feature is usable and testable even without actual inline
encryption hardware.
Per-filesystem changes will be needed to set encryption contexts when
submitting bios and to implement the 'inlinecrypt' mount option. This
patch just adds the common code.
Signed-off-by: Satya Tangirala <satyat@google.com>
Reviewed-by: Jaegeuk Kim <jaegeuk@kernel.org>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20200702015607.1215430-3-satyat@google.com
Co-developed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
The eMMC inline crypto standard will only specify 32 DUN bits (a.k.a. IV
bits), unlike UFS's 64. IV_INO_LBLK_64 is therefore not applicable, but
an encryption format which uses one key per policy and permits the
moving of encrypted file contents (as f2fs's garbage collector requires)
is still desirable.
To support such hardware, add a new encryption format IV_INO_LBLK_32
that makes the best use of the 32 bits: the IV is set to
'SipHash-2-4(inode_number) + file_logical_block_number mod 2^32', where
the SipHash key is derived from the fscrypt master key. We hash only
the inode number and not also the block number, because we need to
maintain contiguity of DUNs to merge bios.
Unlike with IV_INO_LBLK_64, with this format IV reuse is possible; this
is unavoidable given the size of the DUN. This means this format should
only be used where the requirements of the first paragraph apply.
However, the hash spreads out the IVs in the whole usable range, and the
use of a keyed hash makes it difficult for an attacker to determine
which files use which IVs.
Besides the above differences, this flag works like IV_INO_LBLK_64 in
that on ext4 it is only allowed if the stable_inodes feature has been
enabled to prevent inode numbers and the filesystem UUID from changing.
Link: https://lore.kernel.org/r/20200515204141.251098-1-ebiggers@kernel.org
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Paul Crowley <paulcrowley@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Fix all kerneldoc warnings in fs/crypto/ and include/linux/fscrypt.h.
Most of these were due to missing documentation for function parameters.
Detected with:
scripts/kernel-doc -v -none fs/crypto/*.{c,h} include/linux/fscrypt.h
This cleanup makes it possible to check new patches for kerneldoc
warnings without having to filter out all the existing ones.
For consistency, also adjust some function "brief descriptions" to
include the parentheses and to wrap at 80 characters. (The latter
matches the checkpatch expectation.)
Link: https://lore.kernel.org/r/20200511191358.53096-2-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Document that fscrypt_encrypt_pagecache_blocks() allocates the bounce
page from a mempool, and document what this means for the @gfp_flags
argument.
Link: https://lore.kernel.org/r/20191231181026.47400-1-ebiggers@kernel.org
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Biggers <ebiggers@google.com>
fscrypt_d_revalidate() and fscrypt_d_ops really belong in fname.c, since
they're specific to filenames encryption. crypto.c is for contents
encryption and general fs/crypto/ initialization and utilities.
Link: https://lore.kernel.org/r/20191209204359.228544-1-ebiggers@kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Inline encryption hardware compliant with the UFS v2.1 standard or with
the upcoming version of the eMMC standard has the following properties:
(1) Per I/O request, the encryption key is specified by a previously
loaded keyslot. There might be only a small number of keyslots.
(2) Per I/O request, the starting IV is specified by a 64-bit "data unit
number" (DUN). IV bits 64-127 are assumed to be 0. The hardware
automatically increments the DUN for each "data unit" of
configurable size in the request, e.g. for each filesystem block.
Property (1) makes it inefficient to use the traditional fscrypt
per-file keys. Property (2) precludes the use of the existing
DIRECT_KEY fscrypt policy flag, which needs at least 192 IV bits.
Therefore, add a new fscrypt policy flag IV_INO_LBLK_64 which causes the
encryption to modified as follows:
- The encryption keys are derived from the master key, encryption mode
number, and filesystem UUID.
- The IVs are chosen as (inode_number << 32) | file_logical_block_num.
For filenames encryption, file_logical_block_num is 0.
Since the file nonces aren't used in the key derivation, many files may
share the same encryption key. This is much more efficient on the
target hardware. Including the inode number in the IVs and mixing the
filesystem UUID into the keys ensures that data in different files is
nevertheless still encrypted differently.
Additionally, limiting the inode and block numbers to 32 bits and
placing the block number in the low bits maintains compatibility with
the 64-bit DUN convention (property (2) above).
Since this scheme assumes that inode numbers are stable (which may
preclude filesystem shrinking) and that inode and file logical block
numbers are at most 32-bit, IV_INO_LBLK_64 will only be allowed on
filesystems that meet these constraints. These are acceptable
limitations for the cases where this format would actually be used.
Note that IV_INO_LBLK_64 is an on-disk format, not an implementation.
This patch just adds support for it using the existing filesystem layer
encryption. A later patch will add support for inline encryption.
Reviewed-by: Paul Crowley <paulcrowley@google.com>
Co-developed-by: Satya Tangirala <satyat@google.com>
Signed-off-by: Satya Tangirala <satyat@google.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Now that ext4 and f2fs implement their own post-read workflow that
supports both fscrypt and fsverity, the fscrypt-only workflow based
around struct fscrypt_ctx is no longer used. So remove the unused code.
This is based on a patch from Chandan Rajendra's "Consolidate FS read
I/O callbacks code" patchset, but rebased onto the latest kernel, folded
__fscrypt_decrypt_bio() into fscrypt_decrypt_bio(), cleaned up
fscrypt_initialize(), and updated the commit message.
Originally-from: Chandan Rajendra <chandan@linux.ibm.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Instead of open-coding the calculations for ESSIV handling, use an ESSIV
skcipher which does all of this under the hood. ESSIV was added to the
crypto API in v5.4.
This is based on a patch from Ard Biesheuvel, but reworked to apply
after all the fscrypt changes that went into v5.4.
Tested with 'kvm-xfstests -c ext4,f2fs -g encrypt', including the
ciphertext verification tests for v1 and v2 encryption policies.
Originally-from: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Add a new fscrypt policy version, "v2". It has the following changes
from the original policy version, which we call "v1" (*):
- Master keys (the user-provided encryption keys) are only ever used as
input to HKDF-SHA512. This is more flexible and less error-prone, and
it avoids the quirks and limitations of the AES-128-ECB based KDF.
Three classes of cryptographically isolated subkeys are defined:
- Per-file keys, like used in v1 policies except for the new KDF.
- Per-mode keys. These implement the semantics of the DIRECT_KEY
flag, which for v1 policies made the master key be used directly.
These are also planned to be used for inline encryption when
support for it is added.
- Key identifiers (see below).
- Each master key is identified by a 16-byte master_key_identifier,
which is derived from the key itself using HKDF-SHA512. This prevents
users from associating the wrong key with an encrypted file or
directory. This was easily possible with v1 policies, which
identified the key by an arbitrary 8-byte master_key_descriptor.
- The key must be provided in the filesystem-level keyring, not in a
process-subscribed keyring.
The following UAPI additions are made:
- The existing ioctl FS_IOC_SET_ENCRYPTION_POLICY can now be passed a
fscrypt_policy_v2 to set a v2 encryption policy. It's disambiguated
from fscrypt_policy/fscrypt_policy_v1 by the version code prefix.
- A new ioctl FS_IOC_GET_ENCRYPTION_POLICY_EX is added. It allows
getting the v1 or v2 encryption policy of an encrypted file or
directory. The existing FS_IOC_GET_ENCRYPTION_POLICY ioctl could not
be used because it did not have a way for userspace to indicate which
policy structure is expected. The new ioctl includes a size field, so
it is extensible to future fscrypt policy versions.
- The ioctls FS_IOC_ADD_ENCRYPTION_KEY, FS_IOC_REMOVE_ENCRYPTION_KEY,
and FS_IOC_GET_ENCRYPTION_KEY_STATUS now support managing keys for v2
encryption policies. Such keys are kept logically separate from keys
for v1 encryption policies, and are identified by 'identifier' rather
than by 'descriptor'. The 'identifier' need not be provided when
adding a key, since the kernel will calculate it anyway.
This patch temporarily keeps adding/removing v2 policy keys behind the
same permission check done for adding/removing v1 policy keys:
capable(CAP_SYS_ADMIN). However, the next patch will carefully take
advantage of the cryptographically secure master_key_identifier to allow
non-root users to add/remove v2 policy keys, thus providing a full
replacement for v1 policies.
(*) Actually, in the API fscrypt_policy::version is 0 while on-disk
fscrypt_context::format is 1. But I believe it makes the most sense
to advance both to '2' to have them be in sync, and to consider the
numbering to start at 1 except for the API quirk.
Reviewed-by: Paul Crowley <paulcrowley@google.com>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Add a new fscrypt ioctl, FS_IOC_ADD_ENCRYPTION_KEY. This ioctl adds an
encryption key to the filesystem's fscrypt keyring ->s_master_keys,
making any files encrypted with that key appear "unlocked".
Why we need this
~~~~~~~~~~~~~~~~
The main problem is that the "locked/unlocked" (ciphertext/plaintext)
status of encrypted files is global, but the fscrypt keys are not.
fscrypt only looks for keys in the keyring(s) the process accessing the
filesystem is subscribed to: the thread keyring, process keyring, and
session keyring, where the session keyring may contain the user keyring.
Therefore, userspace has to put fscrypt keys in the keyrings for
individual users or sessions. But this means that when a process with a
different keyring tries to access encrypted files, whether they appear
"unlocked" or not is nondeterministic. This is because it depends on
whether the files are currently present in the inode cache.
Fixing this by consistently providing each process its own view of the
filesystem depending on whether it has the key or not isn't feasible due
to how the VFS caches work. Furthermore, while sometimes users expect
this behavior, it is misguided for two reasons. First, it would be an
OS-level access control mechanism largely redundant with existing access
control mechanisms such as UNIX file permissions, ACLs, LSMs, etc.
Encryption is actually for protecting the data at rest.
Second, almost all users of fscrypt actually do need the keys to be
global. The largest users of fscrypt, Android and Chromium OS, achieve
this by having PID 1 create a "session keyring" that is inherited by
every process. This works, but it isn't scalable because it prevents
session keyrings from being used for any other purpose.
On general-purpose Linux distros, the 'fscrypt' userspace tool [1] can't
similarly abuse the session keyring, so to make 'sudo' work on all
systems it has to link all the user keyrings into root's user keyring
[2]. This is ugly and raises security concerns. Moreover it can't make
the keys available to system services, such as sshd trying to access the
user's '~/.ssh' directory (see [3], [4]) or NetworkManager trying to
read certificates from the user's home directory (see [5]); or to Docker
containers (see [6], [7]).
By having an API to add a key to the *filesystem* we'll be able to fix
the above bugs, remove userspace workarounds, and clearly express the
intended semantics: the locked/unlocked status of an encrypted directory
is global, and encryption is orthogonal to OS-level access control.
Why not use the add_key() syscall
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We use an ioctl for this API rather than the existing add_key() system
call because the ioctl gives us the flexibility needed to implement
fscrypt-specific semantics that will be introduced in later patches:
- Supporting key removal with the semantics such that the secret is
removed immediately and any unused inodes using the key are evicted;
also, the eviction of any in-use inodes can be retried.
- Calculating a key-dependent cryptographic identifier and returning it
to userspace.
- Allowing keys to be added and removed by non-root users, but only keys
for v2 encryption policies; and to prevent denial-of-service attacks,
users can only remove keys they themselves have added, and a key is
only really removed after all users who added it have removed it.
Trying to shoehorn these semantics into the keyrings syscalls would be
very difficult, whereas the ioctls make things much easier.
However, to reuse code the implementation still uses the keyrings
service internally. Thus we get lockless RCU-mode key lookups without
having to re-implement it, and the keys automatically show up in
/proc/keys for debugging purposes.
References:
[1] https://github.com/google/fscrypt
[2] https://goo.gl/55cCrI#heading=h.vf09isp98isb
[3] https://github.com/google/fscrypt/issues/111#issuecomment-444347939
[4] https://github.com/google/fscrypt/issues/116
[5] https://bugs.launchpad.net/ubuntu/+source/fscrypt/+bug/1770715
[6] https://github.com/google/fscrypt/issues/128
[7] https://askubuntu.com/questions/1130306/cannot-run-docker-on-an-encrypted-filesystem
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Update fs/crypto/ to use the new names for the UAPI constants rather
than the old names, then make the old definitions conditional on
!__KERNEL__.
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Most of the warning and error messages in fs/crypto/ are for situations
related to a specific inode, not merely to a super_block. So to make
things easier, make fscrypt_msg() take an inode rather than a
super_block, and make it print the inode number.
Note: This is the same approach I'm taking for fsverity_msg().
Signed-off-by: Eric Biggers <ebiggers@google.com>
Since commit 643fa9612b ("fscrypt: remove filesystem specific build
config option"), fs/crypto/ can no longer be built as a loadable module.
Thus it no longer needs a module_exit function, nor a MODULE_LICENSE.
So remove them, and change module_init to late_initcall.
Reviewed-by: Chandan Rajendra <chandan@linux.ibm.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Rename fscrypt_decrypt_page() to fscrypt_decrypt_pagecache_blocks() and
redefine its behavior to decrypt all filesystem blocks in the given
region of the given page, rather than assuming that the region consists
of just one filesystem block. Also remove the 'inode' and 'lblk_num'
parameters, since they can be retrieved from the page as it's already
assumed to be a pagecache page.
This is in preparation for allowing encryption on ext4 filesystems with
blocksize != PAGE_SIZE.
This is based on work by Chandan Rajendra.
Reviewed-by: Chandan Rajendra <chandan@linux.ibm.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Currently fscrypt_decrypt_page() does one of two logically distinct
things depending on whether FS_CFLG_OWN_PAGES is set in the filesystem's
fscrypt_operations: decrypt a pagecache page in-place, or decrypt a
filesystem block in-place in any page. Currently these happen to share
the same implementation, but this conflates the notion of blocks and
pages. It also makes it so that all callers have to provide inode and
lblk_num, when fscrypt could determine these itself for pagecache pages.
Therefore, move the FS_CFLG_OWN_PAGES behavior into a new function
fscrypt_decrypt_block_inplace(). This mirrors
fscrypt_encrypt_block_inplace().
This is in preparation for allowing encryption on ext4 filesystems with
blocksize != PAGE_SIZE.
Reviewed-by: Chandan Rajendra <chandan@linux.ibm.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Rename fscrypt_encrypt_page() to fscrypt_encrypt_pagecache_blocks() and
redefine its behavior to encrypt all filesystem blocks from the given
region of the given page, rather than assuming that the region consists
of just one filesystem block. Also remove the 'inode' and 'lblk_num'
parameters, since they can be retrieved from the page as it's already
assumed to be a pagecache page.
This is in preparation for allowing encryption on ext4 filesystems with
blocksize != PAGE_SIZE.
This is based on work by Chandan Rajendra.
Reviewed-by: Chandan Rajendra <chandan@linux.ibm.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
fscrypt_encrypt_page() behaves very differently depending on whether the
filesystem set FS_CFLG_OWN_PAGES in its fscrypt_operations. This makes
the function difficult to understand and document. It also makes it so
that all callers have to provide inode and lblk_num, when fscrypt could
determine these itself for pagecache pages.
Therefore, move the FS_CFLG_OWN_PAGES behavior into a new function
fscrypt_encrypt_block_inplace().
This is in preparation for allowing encryption on ext4 filesystems with
blocksize != PAGE_SIZE.
Reviewed-by: Chandan Rajendra <chandan@linux.ibm.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Replace some BUG_ON()s with WARN_ON_ONCE() and returning an error code,
and move the check for len divisible by FS_CRYPTO_BLOCK_SIZE into
fscrypt_crypt_block() so that it's done for both encryption and
decryption, not just encryption.
Reviewed-by: Chandan Rajendra <chandan@linux.ibm.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
fscrypt_do_page_crypto() only does a single encryption or decryption
operation, with a single logical block number (single IV). So it
actually operates on a filesystem block, not a "page" per se. To
reflect this, rename it to fscrypt_crypt_block().
Reviewed-by: Chandan Rajendra <chandan@linux.ibm.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Now that fscrypt_ctx is not used for writes, remove the 'w' fields.
Reviewed-by: Chandan Rajendra <chandan@linux.ibm.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Currently, bounce page handling for writes to encrypted files is
unnecessarily complicated. A fscrypt_ctx is allocated along with each
bounce page, page_private(bounce_page) points to this fscrypt_ctx, and
fscrypt_ctx::w::control_page points to the original pagecache page.
However, because writes don't use the fscrypt_ctx for anything else,
there's no reason why page_private(bounce_page) can't just point to the
original pagecache page directly.
Therefore, this patch makes this change. In the process, it also cleans
up the API exposed to filesystems that allows testing whether a page is
a bounce page, getting the pagecache page from a bounce page, and
freeing a bounce page.
Reviewed-by: Chandan Rajendra <chandan@linux.ibm.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make various improvements to fscrypt dentry revalidation:
- Don't try to handle the case where the per-directory key is removed,
as this can't happen without the inode (and dentries) being evicted.
- Flag ciphertext dentries rather than plaintext dentries, since it's
ciphertext dentries that need the special handling.
- Avoid doing unnecessary work for non-ciphertext dentries.
- When revalidating ciphertext dentries, try to set up the directory's
i_crypt_info to make sure the key is really still absent, rather than
invalidating all negative dentries as the previous code did. An old
comment suggested we can't do this for locking reasons, but AFAICT
this comment was outdated and it actually works fine.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
->i_crypt_info starts out NULL and may later be locklessly set to a
non-NULL value by the cmpxchg() in fscrypt_get_encryption_info().
But ->i_crypt_info is used directly, which technically is incorrect.
It's a data race, and it doesn't include the data dependency barrier
needed to safely dereference the pointer on at least one architecture.
Fix this by using READ_ONCE() instead. Note: we don't need to use
smp_load_acquire(), since dereferencing the pointer only requires a data
dependency barrier, which is already included in READ_ONCE(). We also
don't need READ_ONCE() in places where ->i_crypt_info is unconditionally
dereferenced, since it must have already been checked.
Also downgrade the cmpxchg() to cmpxchg_release(), since RELEASE
semantics are sufficient on the write side.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The only reason the inode is being passed to fscrypt_get_ctx() is to
verify that the encryption key is available. However, all callers
already ensure this because if we get as far as trying to do I/O to an
encrypted file without the key, there's already a bug.
Therefore, remove this unnecessary argument.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Add support for the Adiantum encryption mode to fscrypt. Adiantum is a
tweakable, length-preserving encryption mode with security provably
reducible to that of XChaCha12 and AES-256, subject to a security bound.
It's also a true wide-block mode, unlike XTS. See the paper
"Adiantum: length-preserving encryption for entry-level processors"
(https://eprint.iacr.org/2018/720.pdf) for more details. Also see
commit 059c2a4d8e ("crypto: adiantum - add Adiantum support").
On sufficiently long messages, Adiantum's bottlenecks are XChaCha12 and
the NH hash function. These algorithms are fast even on processors
without dedicated crypto instructions. Adiantum makes it feasible to
enable storage encryption on low-end mobile devices that lack AES
instructions; currently such devices are unencrypted. On ARM Cortex-A7,
on 4096-byte messages Adiantum encryption is about 4 times faster than
AES-256-XTS encryption; decryption is about 5 times faster.
In fscrypt, Adiantum is suitable for encrypting both file contents and
names. With filenames, it fixes a known weakness: when two filenames in
a directory share a common prefix of >= 16 bytes, with CTS-CBC their
encrypted filenames share a common prefix too, leaking information.
Adiantum does not have this problem.
Since Adiantum also accepts long tweaks (IVs), it's also safe to use the
master key directly for Adiantum encryption rather than deriving
per-file keys, provided that the per-file nonce is included in the IVs
and the master key isn't used for any other encryption mode. This
configuration saves memory and improves performance. A new fscrypt
policy flag is added to allow users to opt-in to this configuration.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
In this round, we've mainly focused on discard, aka unmap, control along with
fstrim for Android-specific usage model. In addition, we've fixed writepage flow
which returned EAGAIN previously resulting in EIO of fsync(2) due to mapping's
error state. In order to avoid old MM bug [1], we decided not to use __GFP_ZERO
for the mapping for node and meta page caches. As always, we've cleaned up many
places for future fsverity and symbol conflicts.
Enhancement:
- do discard/fstrim in lower priority considering fs utilization
- split large discard commands into smaller ones for better responsiveness
- add more sanity checks to address syzbot reports
- add a mount option, fsync_mode=nobarrier, which can reduce # of cache flushes
- clean up symbol namespace with modified function names
- be strict on block allocation and IO control in corner cases
Bug fix:
- don't use __GFP_ZERO for mappings
- fix error reports in writepage to avoid fsync() failure
- avoid selinux denial on CAP_RESOURCE on resgid/resuid
- fix some subtle race conditions in GC/atomic writes/shutdown
- fix overflow bugs in sanity_check_raw_super
- fix missing bits on get_flags
Clean-up:
- prepare the generic flow for future fsverity integration
- fix some broken coding standard
[1] https://lkml.org/lkml/2018/4/8/661
-----BEGIN PGP SIGNATURE-----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=JrW7
-----END PGP SIGNATURE-----
Merge tag 'f2fs-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"In this round, we've mainly focused on discard, aka unmap, control
along with fstrim for Android-specific usage model. In addition, we've
fixed writepage flow which returned EAGAIN previously resulting in EIO
of fsync(2) due to mapping's error state. In order to avoid old MM bug
[1], we decided not to use __GFP_ZERO for the mapping for node and
meta page caches. As always, we've cleaned up many places for future
fsverity and symbol conflicts.
Enhancements:
- do discard/fstrim in lower priority considering fs utilization
- split large discard commands into smaller ones for better responsiveness
- add more sanity checks to address syzbot reports
- add a mount option, fsync_mode=nobarrier, which can reduce # of cache flushes
- clean up symbol namespace with modified function names
- be strict on block allocation and IO control in corner cases
Bug fixes:
- don't use __GFP_ZERO for mappings
- fix error reports in writepage to avoid fsync() failure
- avoid selinux denial on CAP_RESOURCE on resgid/resuid
- fix some subtle race conditions in GC/atomic writes/shutdown
- fix overflow bugs in sanity_check_raw_super
- fix missing bits on get_flags
Clean-ups:
- prepare the generic flow for future fsverity integration
- fix some broken coding standard"
[1] https://lkml.org/lkml/2018/4/8/661
* tag 'f2fs-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (79 commits)
f2fs: fix to clear FI_VOLATILE_FILE correctly
f2fs: let sync node IO interrupt async one
f2fs: don't change wbc->sync_mode
f2fs: fix to update mtime correctly
fs: f2fs: insert space around that ':' and ', '
fs: f2fs: add missing blank lines after declarations
fs: f2fs: changed variable type of offset "unsigned" to "loff_t"
f2fs: clean up symbol namespace
f2fs: make set_de_type() static
f2fs: make __f2fs_write_data_pages() static
f2fs: fix to avoid accessing cross the boundary
f2fs: fix to let caller retry allocating block address
disable loading f2fs module on PAGE_SIZE > 4KB
f2fs: fix error path of move_data_page
f2fs: don't drop dentry pages after fs shutdown
f2fs: fix to avoid race during access gc_thread pointer
f2fs: clean up with clear_radix_tree_dirty_tag
f2fs: fix to don't trigger writeback during recovery
f2fs: clear discard_wake earlier
f2fs: let discard thread wait a little longer if dev is busy
...
Use a common function for fscrypt warning and error messages so that all
the messages are consistently ratelimited, include the "fscrypt:"
prefix, and include the filesystem name if applicable.
Also fix up a few of the log messages to be more descriptive.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
skcipher_request_alloc() can only fail due to lack of memory, and in
that case the memory allocator will have already printed a detailed
error message. Thus, remove the redundant error messages from fscrypt.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Now that all filesystems have been converted to use
fscrypt_prepare_lookup(), we can remove the fscrypt_set_d_op() and
fscrypt_set_encrypted_dentry() functions as well as un-export
fscrypt_d_ops.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Improve fscrypt read performance by switching the decryption workqueue
from bound to unbound. With the bound workqueue, when multiple bios
completed on the same CPU, they were decrypted on that same CPU. But
with the unbound queue, they are now decrypted in parallel on any CPU.
Although fscrypt read performance can be tough to measure due to the
many sources of variation, this change is most beneficial when
decryption is slow, e.g. on CPUs without AES instructions. For example,
I timed tarring up encrypted directories on f2fs. On x86 with AES-NI
instructions disabled, the unbound workqueue improved performance by
about 25-35%, using 1 to NUM_CPUs jobs with 4 or 8 CPUs available. But
with AES-NI enabled, performance was unchanged to within ~2%.
I also did the same test on a quad-core ARM CPU using xts-speck128-neon
encryption. There performance was usually about 10% better with the
unbound workqueue, bringing it closer to the unencrypted speed.
The unbound workqueue may be worse in some cases due to worse locality,
but I think it's still the better default. dm-crypt uses an unbound
workqueue by default too, so this change makes fscrypt match.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Currently, fscrypt provides fscrypt_decrypt_bio_pages() which decrypts a
bio's pages asynchronously, then unlocks them afterwards. But, this
assumes that decryption is the last "postprocessing step" for the bio,
so it's incompatible with additional postprocessing steps such as
authenticity verification after decryption.
Therefore, rename the existing fscrypt_decrypt_bio_pages() to
fscrypt_enqueue_decrypt_bio(). Then, add fscrypt_decrypt_bio() which
decrypts the pages in the bio synchronously without unlocking the pages,
nor setting them Uptodate; and add fscrypt_enqueue_decrypt_work(), which
enqueues work on the fscrypt_read_workqueue. The new functions will be
used by filesystems that support both fscrypt and fs-verity.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
fscrypt.h included way too many other headers, given that it is included
by filesystems both with and without encryption support. Trim down the
includes list by moving the needed includes into more appropriate
places, and removing the unneeded ones.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAloI8AUACgkQ8vlZVpUN
gaMdjgf8CCW7UhPjoZYwF8sUNtAaX9+JZT1maOcXUhpJ3vRQiRn+AzRH6yBYMm79
+NZBwVlk4dlEe55Wh4yFIStMAstqzCrke4C9CSbExjgHNsJdU4znyYuLRMbLfyO0
6c4NObiAIKJdW1/te1aN90keGC6min8pBZot+FqZsRr+Kq2+IOtM43JAv7efOLev
v3LCjUf9JKxatoB8tgw4AJRa1p18p7D2APWTG05VlFq63TjhVIYNvvwcQlizLwGY
cuEq3X59FbFdX06fJnucujU3WP3ES4/3rhufBK4NNaec5e5dbnH2KlAx7J5SyMIZ
0qUFB/dmXDSb3gsfScSGo1F71Ad0CA==
=asAm
-----END PGP SIGNATURE-----
Merge tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/fscrypt
Pull fscrypt updates from Ted Ts'o:
"Lots of cleanups, mostly courtesy by Eric Biggers"
* tag 'fscrypt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/fscrypt:
fscrypt: lock mutex before checking for bounce page pool
fscrypt: add a documentation file for filesystem-level encryption
ext4: switch to fscrypt_prepare_setattr()
ext4: switch to fscrypt_prepare_lookup()
ext4: switch to fscrypt_prepare_rename()
ext4: switch to fscrypt_prepare_link()
ext4: switch to fscrypt_file_open()
fscrypt: new helper function - fscrypt_prepare_setattr()
fscrypt: new helper function - fscrypt_prepare_lookup()
fscrypt: new helper function - fscrypt_prepare_rename()
fscrypt: new helper function - fscrypt_prepare_link()
fscrypt: new helper function - fscrypt_file_open()
fscrypt: new helper function - fscrypt_require_key()
fscrypt: remove unneeded empty fscrypt_operations structs
fscrypt: remove ->is_encrypted()
fscrypt: switch from ->is_encrypted() to IS_ENCRYPTED()
fs, fscrypt: add an S_ENCRYPTED inode flag
fscrypt: clean up include file mess
fscrypt starts several async. crypto ops and waiting for them to
complete. Move it over to generic code doing the same.
Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
fscrypt_initialize(), which allocates the global bounce page pool when
an encrypted file is first accessed, uses "double-checked locking" to
try to avoid locking fscrypt_init_mutex. However, it doesn't use any
memory barriers, so it's theoretically possible for a thread to observe
a bounce page pool which has not been fully initialized. This is a
classic bug with "double-checked locking".
While "only a theoretical issue" in the latest kernel, in pre-4.8
kernels the pointer that was checked was not even the last to be
initialized, so it was easily possible for a crash (NULL pointer
dereference) to happen. This was changed only incidentally by the large
refactor to use fs/crypto/.
Solve both problems in a trivial way that can easily be backported: just
always take the mutex. It's theoretically less efficient, but it
shouldn't be noticeable in practice as the mutex is only acquired very
briefly once per encrypted file.
Later I'd like to make this use a helper macro like DO_ONCE(). However,
DO_ONCE() runs in atomic context, so we'd need to add a new macro that
allows blocking.
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
IS_ENCRYPTED() now gives the same information as
i_sb->s_cop->is_encrypted() but is more efficient, since IS_ENCRYPTED()
is just a simple flag check. Prepare to remove ->is_encrypted() by
switching all callers to IS_ENCRYPTED().
Acked-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
fscrypt provides facilities to use different encryption algorithms which
are selectable by userspace when setting the encryption policy. Currently,
only AES-256-XTS for file contents and AES-256-CBC-CTS for file names are
implemented. This is a clear case of kernel offers the mechanism and
userspace selects a policy. Similar to what dm-crypt and ecryptfs have.
This patch adds support for using AES-128-CBC for file contents and
AES-128-CBC-CTS for file name encryption. To mitigate watermarking
attacks, IVs are generated using the ESSIV algorithm. While AES-CBC is
actually slightly less secure than AES-XTS from a security point of view,
there is more widespread hardware support. Using AES-CBC gives us the
acceptable performance while still providing a moderate level of security
for persistent storage.
Especially low-powered embedded devices with crypto accelerators such as
CAAM or CESA often only support AES-CBC. Since using AES-CBC over AES-XTS
is basically thought of a last resort, we use AES-128-CBC over AES-256-CBC
since it has less encryption rounds and yields noticeable better
performance starting from a file size of just a few kB.
Signed-off-by: Daniel Walter <dwalter@sigma-star.at>
[david@sigma-star.at: addressed review comments]
Signed-off-by: David Gstir <david@sigma-star.at>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Filesystem encryption ostensibly supported revoking a keyring key that
had been used to "unlock" encrypted files, causing those files to become
"locked" again. This was, however, buggy for several reasons, the most
severe of which was that when key revocation happened to be detected for
an inode, its fscrypt_info was immediately freed, even while other
threads could be using it for encryption or decryption concurrently.
This could be exploited to crash the kernel or worse.
This patch fixes the use-after-free by removing the code which detects
the keyring key having been revoked, invalidated, or expired. Instead,
an encrypted inode that is "unlocked" now simply remains unlocked until
it is evicted from memory. Note that this is no worse than the case for
block device-level encryption, e.g. dm-crypt, and it still remains
possible for a privileged user to evict unused pages, inodes, and
dentries by running 'sync; echo 3 > /proc/sys/vm/drop_caches', or by
simply unmounting the filesystem. In fact, one of those actions was
already needed anyway for key revocation to work even somewhat sanely.
This change is not expected to break any applications.
In the future I'd like to implement a real API for fscrypt key
revocation that interacts sanely with ongoing filesystem operations ---
waiting for existing operations to complete and blocking new operations,
and invalidating and sanitizing key material and plaintext from the VFS
caches. But this is a hard problem, and for now this bug must be fixed.
This bug affected almost all versions of ext4, f2fs, and ubifs
encryption, and it was potentially reachable in any kernel configured
with encryption support (CONFIG_EXT4_ENCRYPTION=y,
CONFIG_EXT4_FS_ENCRYPTION=y, CONFIG_F2FS_FS_ENCRYPTION=y, or
CONFIG_UBIFS_FS_ENCRYPTION=y). Note that older kernels did not use the
shared fs/crypto/ code, but due to the potential security implications
of this bug, it may still be worthwhile to backport this fix to them.
Fixes: b7236e21d5 ("ext4 crypto: reorganize how we store keys in the inode")
Cc: stable@vger.kernel.org # v4.2+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: Michael Halcrow <mhalcrow@google.com>
