The liointc hardware provides separate Interrupt Status Registers (ISR) for
each core. The current code uses always the ISR of core #0, which works
during boot because by default all interrupts are routed to core #0.
When the interrupt routing changes in the firmware configuration then this
causes interrupts to be lost because they are not configured in the
corresponding core.
Use the core index to access the correct ISR instead of a hardcoded 0.
[ tglx: Massaged changelog ]
Fixes: 0858ed035a ("irqchip/loongson-liointc: Add ACPI init support")
Co-developed-by: Tianli Xiong <xiongtianli@loongson.cn>
Signed-off-by: Tianli Xiong <xiongtianli@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240622043338.1566945-1-chenhuacai@loongson.cn
Multi-bridge machines required that all eiointc controllers in the system
are initialized, otherwise the system does not boot.
The initialization happens on the boot CPU during early boot and relies on
cpu_to_node() for identifying the individual nodes.
That works when the number of possible CPUs is large enough, but with a
command line limit, e.g. "nr_cpus=$N" for kdump, but fails when the CPUs
of the secondary nodes are not covered.
During early ACPI enumeration all CPU to node mappings are recorded up to
CONFIG_NR_CPUS. These are accessible via early_cpu_to_node() even in the
case that "nr_cpus=N" truncates the number of possible CPUs and only
provides the possible CPUs via cpu_to_node() translation.
Change the node lookup in the driver to use early_cpu_to_node() so that
even with a limitation on the number of possible CPUs all eointc instances
are initialized.
This can't obviously cure the case where CONFIG_NR_CPUS is too small.
[ tglx: Massaged changelog ]
Fixes: 64cc451e45 ("irqchip/loongson-eiointc: Fix incorrect use of acpi_get_vec_parent")
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240623034113.1808727-1-chenhuacai@loongson.cn
its_vlpi_prop_update() calls lpi_write_config() which obtains the
mapping information for a VLPI without lock held. So it could race
with its_vlpi_unmap().
Since all calls from its_irq_set_vcpu_affinity() require the same
lock to be held, hoist the locking there instead of sprinkling the
locking all over the place.
This bug was discovered using Coverity Static Analysis Security Testing
(SAST) by Synopsys, Inc.
[ tglx: Use guard() instead of goto ]
Fixes: 015ec0386a ("irqchip/gic-v3-its: Add VLPI configuration handling")
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Hagar Hemdan <hagarhem@amazon.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240531162144.28650-1-hagarhem@amazon.com
Now that the PLIC uses a platform driver, the driver is probed later in the
boot process, where interrupts from peripherals might already be pending.
As a result, plic_handle_irq() may be called as early as the call to
irq_set_chained_handler() completes. But this call happens before the
per-context handler is completely set up, so there is a window where
plic_handle_irq() can see incomplete per-context state and crash.
Avoid this by delaying the call to irq_set_chained_handler() until all
handlers from all PLICs are initialized.
Fixes: 8ec99b0331 ("irqchip/sifive-plic: Convert PLIC driver into a platform driver")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Anup Patel <anup@brainfault.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240529215458.937817-1-samuel.holland@sifive.com
Closes: https://lore.kernel.org/r/CAMuHMdVYFFR7K5SbHBLY-JHhb7YpgGMS_hnRWm8H0KD-wBo+4A@mail.gmail.com/
- Core code:
- Interrupt storm detection for the lockup watchdog:
Lockups which are caused by interrupt storms are not easy to debug
because there is no information about the events which make the lockup
detector trigger.
To make this more user friendly, provide an extenstion to interrupt
statistics which allows to take snapshots and an interface to retrieve
the delta to the snapshot. Use this new mechanism in the watchdog code
to do a two stage lockup analysis by taking the snapshot and printing
the deltas for the topmost active interrupts on the second trigger.
Note: This contains both the interrupt and the watchdog changes as
the latter depend on the former obviously.
- Avoid summation loops in the /proc/interrupts output and use the global
counter when possible
- Skip suspended interrupts on CPU hotplug operations to ensure that they
are not delivered before the system resumes the device drivers when
coming out of suspend.
- On CPU hot-unplug interrupts which are affine to the outgoing CPU are
migrated to a different CPU in the affinity mask. This can fail when
the CPUs have no vectors left. Instead of giving up try to migrate it
to any online CPU and thereby breaking the affinity setting in order to
prevent a stale device interrupt which targets an offline CPU
- The usual small cleanups
- Driver code:
- Support for the RISCV AIA MSI controller
- Make the interrupt allocation for the Loongson PCH controller more
flexible to prevent vector exhaustion
- The usual set of cleanups and fixes all over the place
-----BEGIN PGP SIGNATURE-----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=jFLf
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2024-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt subsystem updates from Thomas Gleixner:
"Core code:
- Interrupt storm detection for the lockup watchdog:
Lockups which are caused by interrupt storms are not easy to debug
because there is no information about the events which make the
lockup detector trigger.
To make this more user friendly, provide an extenstion to interrupt
statistics which allows to take snapshots and an interface to
retrieve the delta to the snapshot. Use this new mechanism in the
watchdog code to do a two stage lockup analysis by taking the
snapshot and printing the deltas for the topmost active interrupts
on the second trigger.
Note: This contains both the interrupt and the watchdog changes as
the latter depend on the former obviously.
- Avoid summation loops in the /proc/interrupts output and use the
global counter when possible
- Skip suspended interrupts on CPU hotplug operations to ensure that
they are not delivered before the system resumes the device drivers
when coming out of suspend.
- On CPU hot-unplug interrupts which are affine to the outgoing CPU
are migrated to a different CPU in the affinity mask. This can fail
when the CPUs have no vectors left. Instead of giving up try to
migrate it to any online CPU and thereby breaking the affinity
setting in order to prevent a stale device interrupt which targets
an offline CPU
- The usual small cleanups
Driver code:
- Support for the RISCV AIA MSI controller
- Make the interrupt allocation for the Loongson PCH controller more
flexible to prevent vector exhaustion
- The usual set of cleanups and fixes all over the place"
* tag 'irq-core-2024-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
irqchip/gic-v3-its: Remove BUG_ON in its_vpe_irq_domain_alloc
cpuidle: Avoid explicit cpumask allocation on stack
irqchip/sifive-plic: Avoid explicit cpumask allocation on stack
irqchip/riscv-aplic-direct: Avoid explicit cpumask allocation on stack
irqchip/loongson-eiointc: Avoid explicit cpumask allocation on stack
irqchip/gic-v3-its: Avoid explicit cpumask allocation on stack
irqchip/irq-bcm6345-l1: Avoid explicit cpumask allocation on stack
cpumask: Introduce cpumask_first_and_and()
irqchip/irq-brcmstb-l2: Avoid saving mask on shutdown
genirq: Reuse irq_is_nmi()
genirq/cpuhotplug: Retry with cpu_online_mask when migration fails
genirq/cpuhotplug: Skip suspended interrupts when restoring affinity
arm64: dts: st: Add interrupt parent to pinctrl on stm32mp251
arm64: dts: st: Add exti1 and exti2 nodes on stm32mp251
ARM: dts: stm32: List exti parent interrupts on stm32mp131
ARM: dts: stm32: List exti parent interrupts on stm32mp151
arm64: Kconfig.platforms: Enable STM32_EXTI for ARCH_STM32
irqchip/stm32-exti: Mark events reserved with RIF configuration check
irqchip/stm32-exti: Skip secure events
irqchip/stm32-exti: Convert driver to standard PM
...
This BUG_ON() is useless, because the same effect will be obtained
by letting the code run its course and vm being dereferenced,
triggering an exception.
So just remove this check.
Signed-off-by: Guanrui Huang <guanrui.huang@linux.alibaba.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240418061053.96803-3-guanrui.huang@linux.alibaba.com
The error handling path in its_vpe_irq_domain_alloc() causes a double free
when its_vpe_init() fails after successfully allocating at least one
interrupt. This happens because its_vpe_irq_domain_free() frees the
interrupts along with the area bitmap and the vprop_page and
its_vpe_irq_domain_alloc() subsequently frees the area bitmap and the
vprop_page again.
Fix this by unconditionally invoking its_vpe_irq_domain_free() which
handles all cases correctly and by removing the bitmap/vprop_page freeing
from its_vpe_irq_domain_alloc().
[ tglx: Massaged change log ]
Fixes: 7d75bbb4bc ("irqchip/gic-v3-its: Add VPE irq domain allocation/teardown")
Signed-off-by: Guanrui Huang <guanrui.huang@linux.alibaba.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240418061053.96803-2-guanrui.huang@linux.alibaba.com
In general it's preferable to avoid placing cpumasks on the stack, as
for large values of NR_CPUS these can consume significant amounts of
stack space and make stack overflows more likely.
Use cpumask_first_and_and() to avoid the need for a temporary cpumask on
the stack.
Signed-off-by: Dawei Li <dawei.li@shingroup.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20240416085454.3547175-7-dawei.li@shingroup.cn
In general it's preferable to avoid placing cpumasks on the stack, as
for large values of NR_CPUS these can consume significant amounts of
stack space and make stack overflows more likely.
Use cpumask_first_and_and() to avoid the need for a temporary cpumask on
the stack.
Signed-off-by: Dawei Li <dawei.li@shingroup.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20240416085454.3547175-6-dawei.li@shingroup.cn
In general it's preferable to avoid placing cpumasks on the stack, as
for large values of NR_CPUS these can consume significant amounts of
stack space and make stack overflows more likely.
Use cpumask_first_and_and() to avoid the need for a temporary cpumask on
the stack.
Signed-off-by: Dawei Li <dawei.li@shingroup.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Link: https://lore.kernel.org/r/20240416085454.3547175-5-dawei.li@shingroup.cn
In general it's preferable to avoid placing cpumasks on the stack, as
for large values of NR_CPUS these can consume significant amounts of
stack space and make stack overflows more likely.
Remove cpumask var on stack and use cpumask_any_and() to address it.
Signed-off-by: Dawei Li <dawei.li@shingroup.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240416085454.3547175-4-dawei.li@shingroup.cn
In general it's preferable to avoid placing cpumasks on the stack, as
for large values of NR_CPUS these can consume significant amounts of
stack space and make stack overflows more likely.
Use cpumask_first_and_and() to avoid the need for a temporary cpumask on
the stack.
Signed-off-by: Dawei Li <dawei.li@shingroup.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240416085454.3547175-3-dawei.li@shingroup.cn
The interrupt controller shutdown path does not need to save the mask of
enabled interrupts because the next state the system is going to be in is
akin to a cold boot, or a kexec'd kernel. Saving the mask only makes sense
if the software state needs to preserve the hardware state across a system
suspend/resume cycle.
As an optimization, and given that there are systems with dozens of such
interrupt controller, save a "slow" memory mapped I/O read in the shutdown
path where no saving/restoring is required.
Reported-by: Tim Ross <tim.ross@broadcom.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240424175732.1526531-1-florian.fainelli@broadcom.com
EXTI events availability depends on Resource Isolation Framework (RIF)
configuration.
RIF grants access to buses with Compartment ID (CID) filtering, secure and
privilege level. It also assigns EXTI events to one or several processors
(CID, Secure, Privilege).
EXTI events used by Linux must be CID-filtered (EnCIDCFGR.CFEN=1) and
statically assigned to CID1 (EnCIDCFR.CID=CID1).
EXTI events not filling these conditions are marked as reserved and can't
be used by Linux.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240415134926.1254428-7-antonio.borneo@foss.st.com
Secure OS can reserve some EXTI events, marking them as "secure" by setting
the corresponding bit in register SECCFGR (aka TZENR). These events cannot
be used by Linux.
Read the list of reserved events and check it during interrupt domain
allocation.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240415134926.1254428-6-antonio.borneo@foss.st.com
All driver's dependencies for suspend/resume have been fixed long
ago. There are no more reasons to use syscore PM for the part of this
driver related to Cortex-A MPU.
Switch to standard PM using NOIRQ_SYSTEM_SLEEP_PM_OPS, so all the registers
of the interrupt controller get resumed before any irq gets enabled.
A side effect of this change is to drop the only global variable
'stm32_host_data', used to keep the driver's data for syscore_ops. This
makes the driver ready to support multiple EXTI instances.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240415134926.1254428-5-antonio.borneo@foss.st.com
The mapping of EXTI events to its parent interrupt controller is both SoC
and instance dependent.
The current implementation requires adding a new mapping table to the
driver's code and a new compatible for each new EXTI instance.
Check for the presence of the optional interrupts-extended property and use
it to map EXTI events to the parent's interrupts.
For old device trees without the optional interrupts-extended property, the
driver's behavior is unchanged, thus keeps backward compatibility.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240415134926.1254428-4-antonio.borneo@foss.st.com
Commit 046a6ee234 ("irqchip: Bulk conversion to
generic_handle_domain_irq()") incorrectly added a leading space character
in the line indentation.
Use only TAB for indentation, removing the leading space.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240415134926.1254428-2-antonio.borneo@foss.st.com
After commit 5bb578a0c1 ("ARM: 9298/1: Drop custom mdesc->handle_irq()")
the function icoll_handle_irq() is only used within irq-mxs.c. So declare
it as static to fix the warning about a missing prototype when building
with W=1.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The current code is using a fixed mapping between the LS7A interrupt source
and the HT interrupt vector. This prevents the utilization of the full
interrupt vector space and therefore limits the number of interrupt source
in a system.
Replace the fixed mapping with a dynamic mapping which allocates a
vector when an interrupt source is set up. This avoids that unused
sources prevent vectors from being used for other devices.
Introduce a mapping table in struct pch_pic, where each interrupt source
will allocate an index as a 'hwirq' number from the table in the order of
application and set table value as interrupt source number. This hwirq
number will be configured as vector in the HT interrupt controller. For an
interrupt source, the validity period of the obtained hwirq will last until
the system reset.
Co-developed-by: Biao Dong <dongbiao@loongson.cn>
Signed-off-by: Biao Dong <dongbiao@loongson.cn>
Co-developed-by: Tianyang Zhang <zhangtianyang@loongson.cn>
Signed-off-by: Tianyang Zhang <zhangtianyang@loongson.cn>
Signed-off-by: Baoqi Zhang <zhangbaoqi@loongson.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240422093830.27212-1-zhangtianyang@loongson.cn
Currently, the following warning is observed on the QEMU virt machine:
genirq: irq_chip APLIC-MSI-d000000.aplic did not update eff. affinity mask of irq 12
The above warning is because the IMSIC driver does not set the initial
value of effective affinity in the interrupt descriptor. To address this,
initialize the effective affinity in imsic_irq_domain_alloc().
Fixes: 027e125acd ("irqchip/riscv-imsic: Add device MSI domain support for platform devices")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240413065210.315896-1-apatel@ventanamicro.com
As per the GICv4.1 spec (Arm IHI 0069H, 5.3.19):
"A VMAPP with {V, Alloc}=={0, x} is self-synchronizing, This means the ITS
command queue does not show the command as consumed until all of its
effects are completed."
Furthermore, VSYNC is allowed to deliver an SError when referencing a
non existent VPE.
By these definitions, a VMAPP followed by a VSYNC is a bug, as the
later references a VPE that has been unmapped by the former.
Fix it by eliding the VSYNC in this scenario.
Fixes: 64edfaa9a2 ("irqchip/gic-v4.1: Implement the v4.1 flavour of VMAPP")
Signed-off-by: Nianyao Tang <tangnianyao@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20240406022737.3898763-1-tangnianyao@huawei.com
An interrupt's effective affinity can only be different from its configured
affinity if there are multiple CPUs. Make it clear that this option is only
meaningful when SMP is enabled. Otherwise, there exists "WARNING: unmet
direct dependencies detected for GENERIC_IRQ_EFFECTIVE_AFF_MASK" when make
menuconfig if CONFIG_SMP is not set on LoongArch.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240326121130.16622-3-yangtiezhu@loongson.cn
According to the code comment of "struct irq_chip", the member
"irq_set_affinity" is to set the CPU affinity on SMP machines, so define
and call eiointc_set_irq_affinity() only under CONFIG_SMP.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240326121130.16622-4-yangtiezhu@loongson.cn
When pch_msi_parent_domain_alloc() returns an error, there is an off-by-one
in the number of interrupts to be freed.
Fix it by passing the number of successfully allocated interrupts, instead of the
relative index of the last allocated one.
Fixes: 632dcc2c75 ("irqchip: Add Loongson PCH MSI controller")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Link: https://lore.kernel.org/r/20240327142334.1098-1-yuzenghui@huawei.com
When alpine_msix_gic_domain_alloc() fails, there is an off-by-one in the
number of interrupts to be freed.
Fix it by passing the number of successfully allocated interrupts, instead
of the relative index of the last allocated one.
Fixes: 3841245e84 ("irqchip/alpine-msi: Fix freeing of interrupts on allocation error path")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240327142305.1048-1-yuzenghui@huawei.com
armada_370_xp_msi_reenable_percpu() is only defined when CONFIG_PCI_MSI is
enabled, and only called when SMP is enabled.
Without CONFIG_SMP, there are no callers, which results in a build time
warning instead:
drivers/irqchip/irq-armada-370-xp.c:319:13: error: 'armada_370_xp_msi_reenable_percpu' defined but not used [-Werror=unused-function]
319 | static void armada_370_xp_msi_reenable_percpu(void) {}
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Mark the function as __maybe_unused to avoid adding more complexity
to the #ifdefs.
Fixes: 8ca61cde32 ("irqchip/armada-370-xp: Enable MSI affinity configuration")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240322125838.901649-1-arnd@kernel.org
Since commit 021a8ca2ba ("genirq/generic-chip: Fix the irq_chip name for
/proc/interrupts"), the chip name of all chip types are set to the same
name by irq_init_generic_chip() now. So the initialization to the same
irq_chip name are no longer needed. Drop them.
Signed-off-by: Keguang Zhang <keguang.zhang@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20240311115344.72567-1-keguang.zhang@gmail.com
The RISC-V advanced platform-level interrupt controller (APLIC) has
two modes of operation: 1) Direct mode and 2) MSI mode.
(For more details, refer https://github.com/riscv/riscv-aia)
In APLIC MSI-mode, wired interrupts are forwared as message signaled
interrupts (MSIs) to CPUs via IMSIC.
Extend the existing APLIC irqchip driver to support MSI-mode for
RISC-V platforms having both wired interrupts and MSIs.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20240307140307.646078-8-apatel@ventanamicro.com
The RISC-V advanced interrupt architecture (AIA) specification defines
advanced platform-level interrupt controller (APLIC) which has two modes
of operation: 1) Direct mode and 2) MSI mode.
(For more details, refer https://github.com/riscv/riscv-aia)
In APLIC direct-mode, wired interrupts are forwared to CPUs (or HARTs)
as a local external interrupt.
Add a platform irqchip driver for the RISC-V APLIC direct-mode to
support RISC-V platforms having only wired interrupts.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20240307140307.646078-7-apatel@ventanamicro.com
The Linux PCI framework supports per-device MSI domains for PCI devices
so extend the IMSIC driver to allow PCI per-device MSI domains.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20240307140307.646078-5-apatel@ventanamicro.com
The Linux platform MSI support allows per-device MSI domains so add
a platform irqchip driver for RISC-V IMSIC which provides a base IRQ
domain with MSI parent support for platform device domains.
The IMSIC platform driver assumes that the IMSIC state is already
initialized by the IMSIC early driver.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20240307140307.646078-4-apatel@ventanamicro.com
The RISC-V advanced interrupt architecture (AIA) specification
defines a new MSI controller called incoming message signalled
interrupt controller (IMSIC) which manages MSI on per-HART (or
per-CPU) basis. It also supports IPIs as software injected MSIs.
(For more details refer https://github.com/riscv/riscv-aia)
Add an early irqchip driver for RISC-V IMSIC which sets up the
IMSIC state and provide IPIs.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Reviewed-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/r/20240307140307.646078-3-apatel@ventanamicro.com
Simplify rzg2l_irqc_irq_{en,dis}able() by moving common code to
rzg2l_tint_irq_endisable().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
As per the hardware team, TIEN and TINT source should not set at the same
time due to a possible hardware race leading to spurious IRQ.
Currently on some scenarios hardware settings for TINT detection is not in
sync with TINT source as the enable/disable overrides source setting value
leading to hardware inconsistent state. For eg: consider the case GPIOINT0
is used as TINT interrupt and configuring GPIOINT5 as edge type. During
rzg2l_irq_set_type(), TINT source for GPIOINT5 is set. On disable(),
clearing of the entire bytes of TINT source selection for GPIOINT5 is same
as GPIOINT0 with TIEN disabled. Apart from this during enable(), the
setting of GPIOINT5 with TIEN results in spurious IRQ as due to a HW race,
it is possible that IP can use the TIEN with previous source value
(GPIOINT0).
So, just update TIEN during enable/disable as TINT source is already set
during rzg2l_irq_set_type(). This will make the consistent hardware
settings for detection method tied with TINT source and allows to simplify
the code.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
RZ/G2L interrupt chips require that the interrupt is masked before changing
the NMI, IRQ, TINT interrupt settings. Aside of that, after setting an edge
trigger type it is required to clear the interrupt status register in order
to avoid spurious interrupts.
The current implementation fails to do either of that and therefore is
prone to generate spurious interrupts when setting the trigger type.
Address this by:
- Ensuring that the interrupt is masked at the chip level across the
update for the TINT chip
- Clearing the interrupt status register after updating the trigger mode
for edge type interrupts
[ tglx: Massaged changelog and reverted the spin_lock_irqsave() change as
the set_type() callback is always called with interrupts disabled. ]
Fixes: 3fed09559c ("irqchip: Add RZ/G2L IA55 Interrupt Controller driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename rzg2l_irq_eoi()->rzg2l_clear_irq_int() and simplify the code by
removing redundant priv local variable.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename rzg2l_tint_eoi()->rzg2l_clear_tint_int() and simplify the code by
removing redundant priv and hw_irq local variables.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The irq_eoi() callback of the RZ/G2L interrupt chip clears the relevant
interrupt cause bit in the TSCR register by writing to it.
This write is not sufficient because the write is posted and therefore not
guaranteed to immediately clear the bit. Due to that delay the CPU can
raise the just handled interrupt again.
Prevent this by reading the register back which causes the posted write to
be flushed to the hardware before the read completes.
Fixes: 3fed09559c ("irqchip: Add RZ/G2L IA55 Interrupt Controller driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
riscv_intc_custom_base is initialized to BITS_PER_LONG, so the second
check passes even though AIA provides 64 interrupts. Adjust the condition to
only check the custom range for interrupts outside the standard range, and
adjust the standard range when AIA is available.
Fixes: 3c46fc5b55 ("irqchip/riscv-intc: Add support for RISC-V AIA")
Fixes: 678c607ecf ("irqchip/riscv-intc: Fix low-level interrupt handler setup for AIA")
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20240312212813.2323841-1-samuel.holland@sifive.com
- Core and platform-MSI
The core changes have been adopted from previous work which converted
ARM[64] to the new per device MSI domain model, which was merged to
support multiple MSI domain per device. The ARM[64] changes are being
worked on too, but have not been ready yet. The core and platform-MSI
changes have been split out to not hold up RISC-V and to avoid that
RISC-V builds on the scheduled for removal interfaces.
The core support provides new interfaces to handle wire to MSI bridges
in a straight forward way and introduces new platform-MSI interfaces
which are built on top of the per device MSI domain model.
Once ARM[64] is converted over the old platform-MSI interfaces and the
related ugliness in the MSI core code will be removed.
- Drivers:
- Add a new driver for the Andes hart-level interrupt controller
- Rework the SiFive PLIC driver to prepare for MSI suport
- Expand the RISC-V INTC driver to support the new RISC-V AIA
controller which provides the basis for MSI on RISC-V
- A few fixup for the fallout of the core changes.
The actual MSI parts for RISC-V were finalized late and have been
post-poned for the next merge window.
-----BEGIN PGP SIGNATURE-----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=7aXj
-----END PGP SIGNATURE-----
Merge tag 'irq-msi-2024-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI updates from Thomas Gleixner:
"Updates for the MSI interrupt subsystem and initial RISC-V MSI
support.
The core changes have been adopted from previous work which converted
ARM[64] to the new per device MSI domain model, which was merged to
support multiple MSI domain per device. The ARM[64] changes are being
worked on too, but have not been ready yet. The core and platform-MSI
changes have been split out to not hold up RISC-V and to avoid that
RISC-V builds on the scheduled for removal interfaces.
The core support provides new interfaces to handle wire to MSI bridges
in a straight forward way and introduces new platform-MSI interfaces
which are built on top of the per device MSI domain model.
Once ARM[64] is converted over the old platform-MSI interfaces and the
related ugliness in the MSI core code will be removed.
The actual MSI parts for RISC-V were finalized late and have been
post-poned for the next merge window.
Drivers:
- Add a new driver for the Andes hart-level interrupt controller
- Rework the SiFive PLIC driver to prepare for MSI suport
- Expand the RISC-V INTC driver to support the new RISC-V AIA
controller which provides the basis for MSI on RISC-V
- A few fixup for the fallout of the core changes"
* tag 'irq-msi-2024-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (29 commits)
irqchip/riscv-intc: Fix low-level interrupt handler setup for AIA
x86/apic/msi: Use DOMAIN_BUS_GENERIC_MSI for HPET/IO-APIC domain search
genirq/matrix: Dynamic bitmap allocation
irqchip/riscv-intc: Add support for RISC-V AIA
irqchip/sifive-plic: Improve locking safety by using irqsave/irqrestore
irqchip/sifive-plic: Parse number of interrupts and contexts early in plic_probe()
irqchip/sifive-plic: Cleanup PLIC contexts upon irqdomain creation failure
irqchip/sifive-plic: Use riscv_get_intc_hwnode() to get parent fwnode
irqchip/sifive-plic: Use devm_xyz() for managed allocation
irqchip/sifive-plic: Use dev_xyz() in-place of pr_xyz()
irqchip/sifive-plic: Convert PLIC driver into a platform driver
irqchip/riscv-intc: Introduce Andes hart-level interrupt controller
irqchip/riscv-intc: Allow large non-standard interrupt number
genirq/irqdomain: Don't call ops->select for DOMAIN_BUS_ANY tokens
irqchip/imx-intmux: Handle pure domain searches correctly
genirq/msi: Provide MSI_FLAG_PARENT_PM_DEV
genirq/irqdomain: Reroute device MSI create_mapping
genirq/msi: Provide allocation/free functions for "wired" MSI interrupts
genirq/msi: Optionally use dev->fwnode for device domain
genirq/msi: Provide DOMAIN_BUS_WIRED_TO_MSI
...
- Core:
- Make affinity changes immediately effective for interrupt
threads. This reduces the impact on isolated CPUs as it pulls over the
thread right away instead of doing it after the next hardware
interrupt arrived.
- Cleanup and improvements for the interrupt chip simulator
- Deduplication of the interrupt descriptor initialization code so the
sparse and non-sparse mode share more code.
- Drivers:
- A set of conversions to platform_drivers::remove_new() which gets rid
of the pointless return value.
- A new driver for the Starfive JH8100 SoC
- Support for Amlogic-T7 SoCs
- Improvement for the interrupt handling and EOI management for the
loongson interrupt controller.
- The usual fixes and improvements all over the place.
-----BEGIN PGP SIGNATURE-----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=AbVv
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2024-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Core:
- Make affinity changes take effect immediately for interrupt
threads. This reduces the impact on isolated CPUs as it pulls over
the thread right away instead of doing it after the next hardware
interrupt arrived.
- Cleanup and improvements for the interrupt chip simulator
- Deduplication of the interrupt descriptor initialization code so
the sparse and non-sparse mode share more code.
Drivers:
- A set of conversions to platform_drivers::remove_new() which gets
rid of the pointless return value.
- A new driver for the Starfive JH8100 SoC
- Support for Amlogic-T7 SoCs
- Improvement for the interrupt handling and EOI management for the
loongson interrupt controller.
- The usual fixes and improvements all over the place"
* tag 'irq-core-2024-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (33 commits)
irqchip/ts4800: Convert to platform_driver::remove_new() callback
irqchip/stm32-exti: Convert to platform_driver::remove_new() callback
irqchip/renesas-rza1: Convert to platform_driver::remove_new() callback
irqchip/renesas-irqc: Convert to platform_driver::remove_new() callback
irqchip/renesas-intc-irqpin: Convert to platform_driver::remove_new() callback
irqchip/pruss-intc: Convert to platform_driver::remove_new() callback
irqchip/mvebu-pic: Convert to platform_driver::remove_new() callback
irqchip/madera: Convert to platform_driver::remove_new() callback
irqchip/ls-scfg-msi: Convert to platform_driver::remove_new() callback
irqchip/keystone: Convert to platform_driver::remove_new() callback
irqchip/imx-irqsteer: Convert to platform_driver::remove_new() callback
irqchip/imx-intmux: Convert to platform_driver::remove_new() callback
irqchip/imgpdc: Convert to platform_driver::remove_new() callback
irqchip: Add StarFive external interrupt controller
dt-bindings: interrupt-controller: Add starfive,jh8100-intc
arm64: dts: Add gpio_intc node for Amlogic-T7 SoCs
irqchip/meson-gpio: Add support for Amlogic-T7 SoCs
dt-bindings: interrupt-controller: Add support for Amlogic-T7 SoCs
irqchip/vic: Fix a kernel-doc warning
genirq: Wake interrupt threads immediately when changing affinity
...
Use riscv_intc_aia_irq() as the low-level interrupt handler instead of the
existing riscv_intc_irq() default handler to make demultiplexing work
correctly.
Also print "using AIA" in the INTC boot banner when AIA is available.
Fixes: 3c46fc5b55 ("irqchip/riscv-intc: Add support for RISC-V AIA")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240226040746.1396416-2-apatel@ventanamicro.com
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/0bdce86b50e5aa50cffbc4add332cbfbad87521e.1703284359.git.u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Antonio Borneo <antonio.borneo@foss.st.com>
Link: https://lore.kernel.org/r/ac551b89025bafadce05102b94596f8cd3564a32.1703284359.git.u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/1a80e31525d0b02063d2ff1baaaa5e87418f54b6.1703284359.git.u.kleine-koenig@pengutronix.de
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/2d367ab738ed2e4cf58cffc10d64b0cbe8a1322c.1703284359.git.u.kleine-koenig@pengutronix.de
