The R_INTC in the A31 and newer sun8i/sun50i SoCs is more similar to the
original sun4i interrupt controller than the sun7i/sun9i NMI controller.
It is used for two distinct purposes:
- To control the trigger, latch, and mask for the NMI input pin
- To provide the interrupt input for the ARISC coprocessor
As this interrupt controller is not documented, information about it
comes from vendor-provided firmware blobs and from experimentation.
Differences from the sun4i interrupt controller appear to be:
- It only has one or two registers of each kind (max 32 or 64 IRQs)
- Multiplexing logic is added to support additional inputs
- There is no FIQ-related logic
- There is no interrupt priority logic
In order to fulfill its two purposes, this hardware block combines four
types of IRQs. First, the NMI pin is routed to the "IRQ 0" input on this
chip, with a trigger type controlled by the NMI_CTRL_REG. The "IRQ 0
pending" output from this chip, if enabled, is then routed to a SPI IRQ
input on the GIC. In other words, bit 0 of IRQ_ENABLE_REG *does* affect
the NMI IRQ seen at the GIC.
The NMI is followed by a contiguous block of 15 "direct" (my name for
them) IRQ inputs that are connected in parallel to both R_INTC and the
GIC. Or in other words, these bits of IRQ_ENABLE_REG *do not* affect the
IRQs seen at the GIC.
Following the direct IRQs are the ARISC's copy of banked IRQs for shared
peripherals. These are not relevant to Linux. The remaining IRQs are
connected to a multiplexer and provide access to the first (up to) 128
SPIs from the ARISC. This range of SPIs overlaps with the direct IRQs.
Because of the 1:1 correspondence between R_INTC and GIC inputs, this is
a perfect scenario for using a stacked irqchip driver. We want to hook
into setting the NMI trigger type, but not actually handle any IRQ here.
To allow access to all multiplexed IRQs, this driver requires a new
binding where the interrupt number matches the GIC interrupt number.
(This moves the NMI from number 0 to 32 or 96, depending on the SoC.)
For simplicity, copy the three-cell GIC binding; this disambiguates
interrupt 0 in the old binding (the NMI) from interrupt 0 in the new
binding (SPI 0) by the number of cells.
Since R_INTC is in the always-on power domain, and its output is visible
to the power management coprocessor, a stacked irqchip driver provides a
simple way to add wakeup support to any of its IRQs. That is the next
patch; for now, just the NMI is moved over.
This commit mostly reverts commit 173bda53b3 ("irqchip/sunxi-nmi:
Support sun6i-a31-r-intc compatible").
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210118055040.21910-4-samuel@sholland.org
The Allwinner V3 SoC shares the same base as the V3s but comes with
extra pins and features available. As a result, it has its dedicated
compatible string (already used in device trees), which is added here.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201031182137.1879521-2-contact@paulk.fr
The Allwinner platform code is not a clock provider, and just needs to
call of_clk_init().
Hence it can include <linux/of_clk.h> instead of <linux/clk-provider.h>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
PRCM_PWROFF_GATING_REG has CPU0 at bit 4 on A83T. So without this
patch, instead of gating the CPU0, the whole cluster was power gated,
when shutting down first CPU in the cluster.
Fixes: 6961275e72 ("ARM: sun8i: smp: Add support for A83T")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Cc: stable@vger.kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The call to of_get_next_child returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./arch/arm/mach-sunxi/platsmp.c:55:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 46, but without a corresponding object release within this function.
./arch/arm/mach-sunxi/platsmp.c:138:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 129, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The call to of_get_next_child returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./arch/arm/mach-sunxi/mc_smp.c:110:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 97, but without a corresponding object release within this functio
./arch/arm/mach-sunxi/platsmp.c:138:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 129, but without a corresponding object release within this function
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org (open list)
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Avoid declaring extern functions in c files. To make sure function
definition and usage don't get out of sync, declare sun6i_reset_init
in a common header.
Suggested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add option for Allwinner ARMv5 SoCs and SoC F1C100s (which has a die
used for many new F-series products, including F1C100A, F1C100s, F1C200s,
F1C500, F1C600).
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Allwinner also has some ARMv5 SoCs.
In order to add support for them, check ARM_MULTI_V7 before enabling
ARMv7 SoC's. Add help text for ARCH_SUNXI menuconfig.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the support for A83T.
A83T SoC has an additional register than A80 to handle CPU configurations:
R_CPUS_CFG. Information about the register comes from Allwinner's BSP
driver.
An important difference is the Power Off Gating register for clusters
which is BIT(4) in case of SUN9I-A80 and BIT(0) in case of SUN8I-A83T.
There is also a bit swap between sun8i-a83t and sun9i-a80 that must be
handled.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
To prepare the support of sun8i-a83t, add a field in the smp_data
structure to know if we are on sun9i-a80 or sun8i-a83t.
Add also a global variable to retrieve which architecture we are
having.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
To prepare the support for sun8i-a83t, rename the macro that handles
the power-off of clusters because it is different from sun9i-a80 to
sun8i-a83t.
The power off register for clusters are different from a80 and a83t.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add the initialization of CNTVOFF for sun8i-a83t.
For boot CPU, create a new machine that handles this
function's call in an "init_early" callback. We need to initialize
CNTVOFF before the arch timer's initialization otherwise, it will
not be taken into account and fails to boot correctly.
Because of that, this function can't be called in SMP's early_initcall
function which is called after timer's init.
For secondary CPUs, add this function into secondary_startup
assembly entry.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Move the assembly code for cluster cache enabling and resuming
into an assembly file instead of having it directly in C code.
Remove the CFLAGS because we are using the ARM directive "arch"
instead.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The multi-cluster SMP code maps the address spaces of several hardware
control blocks. The device nodes for them are SoC-specific. To help with
supporting other SoCs to re-use this code, these bits should be split
out to a separate function tied to the enable-method string.
This patch splits out and groups the device node lookup sequence, and
adds new data structures to have the newly created function tied to
the enable method string. This structure can also be used to encode
other differences between the SoCs.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Instead of having an early init function check the machine compatible
and installing multi-cluster SMP support for the A80 if it matches,
use a new cpu enable-method string. This makes the platform support
future proof in case anyone manages to add PSCI support.
The original init code for the SMP support is changed into the
.prepare_cpus callback in the smp_operations structure. Instead of
panicing when resources are missing like on some platforms, our code
merely guards against engaging SMP or CPU hotplug and returns an error.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The sunxi_mc_smp_lookback function is modeled after the mcpm_loopback
function in the MCPM framework. "lookback" was a typo introduced when
the new function was added.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The BROM has a branch that checks if the primary core is hotplugging.
If the magic flag is set, execution jumps to the address set in the
software entry register. (Secondary cores always branch to the that
address.)
This patch sets the flags that makes BROM jump execution on the
primary core (cpu0) to the SMP software entry code when the core is
powered back up. After it is re-integrated into the system, the flag
is cleared.
A custom .cpu_can_disable callback that returns true for all cpus,
so that cpu0 can really be brought down.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
This patch adds common code used to power down all cores and clusters.
The code was previously based on the MCPM framework. It has now been
adapted to hook into struct smp_operations directly, but the code
structure still shows signs of prior work.
The primary core (cpu0) requires setting flags to have the BROM bounce
execution to the SMP software entry code. This is done in a subsequent
patch to keep the changes cleanly separated. By default the ARM SMP code
blocks cpu0 from being turned off, so splitting this out is safe.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The A80 is a big.LITTLE SoC with 1 cluster of 4 Cortex-A7s and
1 cluster of 4 Cortex-A15s.
This patch adds support to bring up the second cluster and thus all
cores using custom platform SMP code. Core/cluster power down has not
been implemented, thus CPU hotplugging is not supported.
Parts of the trampoline and re-entry code for the boot cpu was adapted
from the MCPM framework.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Allwinner R40 is a new SoC, with Quad Core Cortex-A7 and peripherals
like A20.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The function name is now renamed to 'timer_probe' for consistency with
the CLOCKSOURCE_OF_DECLARE => TIMER_OF_DECLARE change.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Device frequency scaling is implemented through devfreq in the kernel,
which requires CONFIG_PM_OPP.
Let's select it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pull ARM updates from Russell King:
- nommu updates from Afzal Mohammed cleaning up the vectors support
- allow DMA memory "mapping" for nommu Benjamin Gaignard
- fixing a correctness issue with R_ARM_PREL31 relocations in the
module linker
- add strlen() prototype for the decompressor
- support for DEBUG_VIRTUAL from Florian Fainelli
- adjusting memory bounds after memory reservations have been
registered
- unipher cache handling updates from Masahiro Yamada
- initrd and Thumb Kconfig cleanups
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (23 commits)
ARM: mm: round the initrd reservation to page boundaries
ARM: mm: clean up initrd initialisation
ARM: mm: move initrd init code out of arm_memblock_init()
ARM: 8655/1: improve NOMMU definition of pgprot_*()
ARM: 8654/1: decompressor: add strlen prototype
ARM: 8652/1: cache-uniphier: clean up active way setup code
ARM: 8651/1: cache-uniphier: include <linux/errno.h> instead of <linux/types.h>
ARM: 8650/1: module: handle negative R_ARM_PREL31 addends correctly
ARM: 8649/2: nommu: remove Hivecs configuration is asm
ARM: 8648/2: nommu: display vectors base
ARM: 8647/2: nommu: dynamic exception base address setting
ARM: 8646/1: mmu: decouple VECTORS_BASE from Kconfig
ARM: 8644/1: Reduce "CPU: shutdown" message to debug level
ARM: 8641/1: treewide: Replace uses of virt_to_phys with __pa_symbol
ARM: 8640/1: Add support for CONFIG_DEBUG_VIRTUAL
ARM: 8639/1: Define KERNEL_START and KERNEL_END
ARM: 8638/1: mtd: lart: Rename partition defines to be prefixed with PART_
ARM: 8637/1: Adjust memory boundaries after reservations
ARM: 8636/1: Cleanup sanity_check_meminfo
ARM: add CPU_THUMB_CAPABLE to indicate possible Thumb support
...
All low-level PM/SMP code using virt_to_phys() should actually use
__pa_symbol() against kernel symbols. Update code where relevant to move
away from virt_to_phys().
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allwinner V3s is a low-end single-core Cortex-A7 SoC, with 64MB
integrated DRAM, and several peripherals.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner H2+ is a quad-core Cortex-A7 SoC.
It is very like H3, that they share the same SoC ID (0x1680), and H3
memory maps as well as drivers works well on the SoC.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The GR8 is an SoC made by Nextthing Co, loosely based on the sun5i family.
It has a number of new controllers compared to the A10s and A13 (SPDIF, I2S),
but some controllers missing too (Ethernet, less I2C, less UARTs).
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With previous fixes to stmmac, sun4i-emac and sun4i-mmc at least the
Cubieboard2 incarnation of sunxi works correctly in big-endian mode.
Allow the selection of big-endian.
Tested using a Cubieboard2 DualCard and the following
hardware-components:
- GMAC (stmmac)
- EMAC (sun4i-emac)
- SATA
- SPI
- UART
- security system
- touchscreen controller hwmon functionality
- pinctrl (custom interrupt for SPI ethernet controller)
- watchdog as reset controller
- onboard RTC
- DS1307 I2C RTC
- sound codec and with this indirectly the DMA engine
Signed-off-by: Michael Weiser <michael.weiser@gmx.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This replaces:
- "select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB" as this can
now be selected directly.
- "select ARCH_WANT_OPTIONAL_GPIOLIB" with no dependency: GPIOLIB
is now selectable by everyone, so we need not declare our
intent to select it.
When ordering the symbols the following rationale was used:
if the selects were in alphabetical order, I moved select GPIOLIB
to be in alphabetical order, but if the selects were not
maintained in alphabetical order, I just replaced
"select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB".
Cc: Michael Büsch <m@bues.ch>
Cc: arm@kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Allwinner A83T is octa-core cortex-a7 based SoC.
It's clock control unit and prcm, pinmux are different from previous sun8i
series.
Its processor cores are arragned in two clusters 4 cores each,
similar to A80.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
[maxime: Removed the clock protection code]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Many ARM sub-architectures use prompts followed by "if" conditional,
but it is wrong.
Please notice the difference between
config ARCH_FOO
bool "Foo SoCs" if ARCH_MULTI_V7
and
config ARCH_FOO
bool "Foo SoCs"
depends on ARCH_MULTI_V7
These two are *not* equivalent!
In the former statement, it is not ARCH_FOO, but its prompt that
depends on ARCH_MULTI_V7. So, it is completely valid that ARCH_FOO
is selected by another, but ARCH_MULTI_V7 is still disabled. As it is
not unmet dependency, Kconfig never warns. This is probably not what
you want.
The former should be used only when you need to do so, and you really
understand what you are doing. (In most cases, it should be wrong!)
For enabling/disabling sub-architectures, the latter is always correct.
As a good side effect, this commit fixes some entries over 80 columns
(mach-imx, mach-integrator, mach-mbevu).
[Arnd: I note that there is not really a bug here, according to
the discussion that followed, but I can see value in being consistent
and in making the lines shorter]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Krzysztof Halasa <khc@piap.pl>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
New and/or improved SoC support for this release:
- Marvell Berlin:
* Enable standard DT-based cpufreq
* Add CPU hotplug support
- Freescale:
* Ethernet init for i.MX7D
* Suspend/resume support for i.MX6UL
- Allwinner:
* Support for R8 chipset (used on NTC's $9 C.H.I.P board)
- Mediatek:
* SMP support for some platforms
- Uniphier:
* L2 support
* Cleaned up SMP support, etc.
+ A handful of other patches around above functionality, and a few other
smaller changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=h5xk
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New and/or improved SoC support for this release:
Marvell Berlin:
- Enable standard DT-based cpufreq
- Add CPU hotplug support
Freescale:
- Ethernet init for i.MX7D
- Suspend/resume support for i.MX6UL
Allwinner:
- Support for R8 chipset (used on NTC's $9 C.H.I.P board)
Mediatek:
- SMP support for some platforms
Uniphier:
- L2 support
- Cleaned up SMP support, etc.
plus a handful of other patches around above functionality, and a few
other smaller changes"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
ARM: uniphier: rework SMP operations to use trampoline code
ARM: uniphier: add outer cache support
Documentation: EXYNOS: Update bootloader interface on exynos542x
ARM: mvebu: add broken-idle option
ARM: orion5x: use mac_pton() helper
ARM: at91: pm: at91_pm_suspend_in_sram() must be 8-byte aligned
ARM: sunxi: Add R8 support
ARM: digicolor: select pinctrl/gpio driver
arm: berlin: add CPU hotplug support
arm: berlin: use non-self-cleared reset register to reset cpu
ARM: mediatek: add smp bringup code
ARM: mediatek: enable gpt6 on boot up to make arch timer working
soc: mediatek: Fix random hang up issue while kernel init
soc: ti: qmss: make acc queue support optional in the driver
soc: ti: add firmware file name as part of the driver
Documentation: dt: soc: Add description for knav qmss driver
ARM: S3C64XX: Use PWM lookup table for mach-smartq
ARM: S3C64XX: Use PWM lookup table for mach-hmt
ARM: S3C64XX: Use PWM lookup table for mach-crag6410
ARM: S3C64XX: Use PWM lookup table for smdk6410
...
The R8 is a new Allwinner SoC based on the A13. While both are very
similar, there's still a few differences. Introduce a new compatible to
deal with them.
In order to have a consistent naming, instead of mentioning the Allwinner
A series as the machine name, switch to sun4i/sun5i like what is done for
the other families.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Seeing the 'of' characters in a symbol that is being called from
ACPI seems to freak out people. So let's do a bit of pointless
renaming so that these folks do feel at home.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A bunch of defconfig changes, and some patches to make the Allwinner H3 and
A33 boot properly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=m0CY
-----END PGP SIGNATURE-----
Merge tag 'sunxi-late-for-4.2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner late changes for 4.2" from Maxime Ripard:
Allwinner late changes for 4.2
A bunch of defconfig changes, and some patches to make the Allwinner H3 and
A33 boot properly.
* tag 'sunxi-late-for-4.2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: Enable simplefb in the defconfig
ARM: Remove deprecated symbol from defconfig files
ARM: sunxi: Add Machine support for A33
ARM: sunxi: Introduce Allwinner H3 support
Documentation: sunxi: Update Allwinner SoC documentation
Add machine support for the Allwinner A33 quad core cortex-a7 based SoC,
which is similar to the A23 SoC.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Chen-Yu Tsai <wens@csie.org>
The Allwinner H3 is a quad-core Cortex-A7-based SoC. It is very similar
to other sun8i family SoCs like the A23.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A23 is a dual Cortex-A7. Add the logic to use the IPs used to
control the CPU configuration and the CPU power so that we can
bring up secondary CPUs at boot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As the sunxi usb clocks all contain a reset controller, it is not
possible to build the sunxi clock driver without RESET_CONTROLLER
enabled. Doing so results in an undefined symbol error:
drivers/built-in.o: In function `sunxi_gates_clk_setup':
linux/drivers/clk/sunxi/clk-sunxi.c:1071: undefined reference to
`reset_controller_register'
This is possible if building a minimal kernel without PHY_SUN4I_USB.
The dependency issue is made visible at compile time instead of
link time by the new A80 mmc clocks, which also use a reset control
itself.
This patch makes ARCH_SUNXI select ARCH_HAS_RESET_CONTROLLER and
RESET_CONTROLLER.
Fixes: 559482d1f9 ARM: sunxi: Split the various SoCs support in Kconfig
Cc: <stable@vger.kernel.org> # 3.16+
Reported-by: Lourens Rozema <ik@lourensrozema.nl>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On sun[45678]i, we have one cluster of identical cores sharing a
clock, which is ideal for using cpufreq-dt. Register a platform
device for cpufreq-dt.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
So far the A31s is 100% compatible with the A31, still lets do the same
as what we've done for the A13 / A10s and give it its own compatible string,
in case we need to differentiate later.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Removed unusude CPU_OF_DECLARE_METHOD]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The sun6i SMP ops are currently not marked as static, as reported by
sparse. Let's mark it as such.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 SoC has reset controls matching bus clock gates.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A80 is a new Cortex octo-core A7/A15 big.LITTLE SoC.
While it's processor cores and interconnecting bus are new, it
re-uses many peripherals found in earlier Allwinner SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Now that the restart code has been merged in the watchdog driver, we don't need
the restart code in the mach-sunxi directory anymore.
Remove it entirely.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This is the bulk of new SoC enablement and other platform changes for 3.17:
* Samsung S5PV210 has been converted to DT and multiplatform
* Clock drivers and bindings for some of the lower-end i.MX 1/2 platforms
* Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood.
* Hwmod data for TI AM43xx and DRA7 platforms.
* More additions of Renesas shmobile platform support
* Removal of plat-samsung contents that can be removed with S5PV210 being
multiplatform/DT-enabled and the other two old platforms being removed.
New platforms (most with only basic support right now):
* Hisilicon X5HD2 settop box chipset is introduced
* Mediatek MT6589 (mobile chipset) is introduced
* Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=5TJ6
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This is the bulk of new SoC enablement and other platform changes for
3.17:
- Samsung S5PV210 has been converted to DT and multiplatform
- Clock drivers and bindings for some of the lower-end i.MX 1/2
platforms
- Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood
- Hwmod data for TI AM43xx and DRA7 platforms
- More additions of Renesas shmobile platform support
- Removal of plat-samsung contents that can be removed with S5PV210
being multiplatform/DT-enabled and the other two old platforms
being removed
New platforms (most with only basic support right now):
- Hisilicon X5HD2 settop box chipset is introduced
- Mediatek MT6589 (mobile chipset) is introduced
- Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code"
* tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits)
ARM: hisi: remove smp from machine descriptor
power: reset: move hisilicon reboot code
ARM: dts: Add hix5hd2-dkb dts file.
ARM: debug: Rename Hi3716 to HIX5HD2
ARM: hisi: enable hix5hd2 SoC
ARM: hisi: add ARCH_HISI
MAINTAINERS: add entry for Broadcom ARM STB architecture
ARM: brcmstb: select GISB arbiter and interrupt drivers
ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
ARM: configs: enable SMP in bcm_defconfig
ARM: add SMP support for Broadcom mobile SoCs
Documentation: arm: misc updates to Marvell EBU SoC status
Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC
ARM: mvebu: fix build without platforms selected
ARM: mvebu: add cpuidle support for Armada 38x
ARM: mvebu: add cpuidle support for Armada 370
cpuidle: mvebu: add Armada 38x support
cpuidle: mvebu: add Armada 370 support
cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7
ARM: mvebu: export the SCU address
...
