Adds an entry for Creative USB X-Fi to the rc_config array in
mixer_quirks.c to allow use of volume knob on the device.
Adds support for newer X-Fi Pro card, known as "Model No. SB1095"
with USB ID "041e:3263"
Signed-off-by: Mirko Dietrich <buzz@l4m1.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200806124850.20334-1-buzz@l4m1.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is a spelling mistake in a usb_audio_dbg debug message. Also
replace "param" with "parameter". Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200806105134.46447-1-colin.king@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tegra HDA has audio data buffer for upto tens of frames, this buffer
can help to avoid underflow. HW will keep issuing new data fetch
request when buffers are not full and current BDL is not done. When SW
disable DMA RUN bit for a stream, HW can't cancel the already issued data
fetch request and hence it can't stop DMA. HW has to wait for all issued
data fetch request get data returned before it stops DMA.
This HW behavior is not in sync with HDA spec which says DMA RUN bit
should be cleared within 1 audio frame. For Tegra, DMA RUN bit was
active for more than one audio frame, due to this the timeout in
snd_hdac_stream_sync function is not helping. When Stream reset set
and clear happens during DMA RUN bit active state it results in Memory
Decode error.
Unfortunately, there is no way to detect when these data accesses have
completed, but testing has shown that a 100us delay between Stream reset
set and clear operation for Tegra avoids the memory decode error.
Therefore, adding a 100us dma stop delay.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20200805095221.5476-4-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A variable dma_stop_delay is added as a new member in hdac_bus
structure to avoid memory decode error incase DMA RUN bit is not
disabled in the given timeout from snd_hdac_stream_sync function and
followed by stream reset which results in memory decode error between
reset set and clear operation.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20200805095221.5476-3-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set chip->align_buffer_size to 1 for Tegra platforms to make the buffer
alignment to be multiple of 128 bytes. This fix is applied as gstreamer
alsasink gets stuck with the default buffer-time and latency-time
parameters with 4 byte buffer alignment.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20200805095221.5476-2-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some ioctls via OSS sequencer API may race and lead to UAF when the
port create and delete are performed concurrently, as spotted by a
couple of syzkaller cases. This patch is an attempt to address it by
serializing the ioctls with the existing register_mutex.
Basically OSS sequencer API is an obsoleted interface and was designed
without much consideration of the concurrency. There are very few
applications with it, and the concurrent performance isn't asked,
hence this "big hammer" approach should be good enough.
Reported-by: syzbot+1a54a94bd32716796edd@syzkaller.appspotmail.com
Reported-by: syzbot+9d2abfef257f3e2d4713@syzkaller.appspotmail.com
Suggested-by: Hillf Danton <hdanton@sina.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200804185815.2453-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDMI on some platforms doesn't enable audio support because its Port
Connectivity [31:30] is set to AC_JACK_PORT_NONE:
Node 0x05 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0b000094: OUT Detect HBR HDMI DP
Pin Default 0x58560010: [N/A] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Devices: 0
Connection: 3
0x02 0x03* 0x04
For now, use a quirk to force connectivity based on SSID. If there are
more platforms affected by the same issue, we can eye for a more generic
solution.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20200804155836.16252-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The dock sold from startech (PID: ICUSBAUDIO7D) has no friendly name
and shows up currently as "USB Sound Device" in ALSA.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20200804010616.3399256-1-cujomalainey@chromium.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo ThinkStation P620 is like other TRX40 boards, is equipped with
two USB audio cards.
USB device (17aa:104d) provides functionality for Internal Speaker and
Front Headset. It's UAC v2, so it supports insertion control (jack
detection). However, when trying to get the connector status of the
speaker, an error occurs:
[ 5.787405] usb 3-1: cannot get connectors status: req = 0x81, wValue = 0x200, wIndex = 0x1000, type = 0
Since the insertion control works perfectly for the headset, the error
for speaker is probably casued by connecting internally. So let's relax
the error for a bit if it's a speaker, and always reports it's connected.
USB device (17aa:1046) is for rear Line-in, Line-out and Microphone.
The insertion control works for all three jacks. However, there's an
Function Unit that doesn't work:
[ 5.905415] usb 3-6: cannot get ctl value: req = 0x83, wValue = 0xc00, wIndex = 0x1300, type = 4
[ 5.905418] usb 3-6: 19:0: cannot get min/max values for control 12 (id 19)
So turn off the FU to avoid the error.
Also, add specific card name for both devices, so userspace can easily
indentify both cards.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20200803142612.17156-1-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The biggest changes here one again come from Mormioto-san who has
continued his dilligent work cleaning up long standing issues in the
APIs, it's particularly nice to see the transition from digital_mute()
to mute_stream() finally completed. There's also been a lot of work on
the x86 code again, this time a big focus has been on cleaning up some
issues identified by various static tests, and on the Freescale systems.
Otherwise the biggest thing has been a lot of driver additions:
- Convert users of digital_mute() to mute_stream().
- Simplify I/O helper functions.
- Add a helper for getting the RTD from a substream.
- Many, many fixes and cleanups to the x86 code.
- New drivers for Freescale MQS and i.MX6sx, Intel KeemBay I2S, Maxim
MAX98360A and MAX98373 Soundwire, several Mediatek boards, nVidia
Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries boards (some
of the first phones I worked on!) and TI J721e EVM.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl8n96MTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0FApB/sFAbX/RWXiH5fBRQnGsfvLznORx9pA
90xR+BgpybawRgTk4Bi87sY5lBI44S4OwUqqI58D+/GD7uchgY2Z2m+4flF9GbDU
VTOvChqL0ZpDh2Crr2+BkSlVjZsA3h0e86W/0qoq3/q4dgb7ZfcLJ2w7A+UDq+kP
tKKqi3mTxXuM78N3Vp8/IobIRpo/fi3Oy2aB+WOiAUD6rV88yzx+QgNkvzwvTcpm
y8ejr2zYPYLHLshUh2S7HJaGyX7NjggGVaUolJtfGT+ArAP6j3JIxikC3Mr9TImd
qaX2BsHNE1XARK8KQXA5qTP7++RlewSSxblpoVRFZwV70On9/L5W4GPp
=OO0s
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.9' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.9
The biggest changes here one again come from Mormioto-san who has
continued his dilligent work cleaning up long standing issues in the
APIs, it's particularly nice to see the transition from digital_mute()
to mute_stream() finally completed. There's also been a lot of work on
the x86 code again, this time a big focus has been on cleaning up some
issues identified by various static tests, and on the Freescale systems.
Otherwise the biggest thing has been a lot of driver additions:
- Convert users of digital_mute() to mute_stream().
- Simplify I/O helper functions.
- Add a helper for getting the RTD from a substream.
- Many, many fixes and cleanups to the x86 code.
- New drivers for Freescale MQS and i.MX6sx, Intel KeemBay I2S, Maxim
MAX98360A and MAX98373 Soundwire, several Mediatek boards, nVidia
Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries boards (some
of the first phones I worked on!) and TI J721e EVM.
This reverts commit 9a6418487b ("ALSA: hda: call runtime_allow()
for all hda controllers").
The reverted patch already introduced some regressions on some
machines:
- on gemini-lake machines, the error of "azx_get_response timeout"
happens in the hda driver.
- on the machines with alc662 codec, the audio jack detection doesn't
work anymore.
Fixes: 9a6418487b ("ALSA: hda: call runtime_allow() for all hda controllers")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208511
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Link: https://lore.kernel.org/r/20200803064638.6139-1-hui.wang@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ca0113 command had the wrong group_id, 0x48 when it should've been
0x30. The front microphone selection should now work.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200803002928.8638-3-conmanx360@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the ZxR headphone gain control was added, the ca0132_switch_get
function was not updated, which meant that the changes to the control
state were not saved when entering/exiting alsamixer.
Signed-off-by: Connor McAdams <conmanx360@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200803002928.8638-1-conmanx360@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are several Loongson-3 based laptops produced by CZC or Lemote,
they use alc269/alc662 codecs and need specific pin-tables, this patch
add their pin-tables.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1596360400-32425-1-git-send-email-chenhc@lemote.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Provide a mechanism for true two-step component registration. This
mimics device registration flow where initialization is the first step
while addition goes as second in line. Drivers may choose to modify
component's fields before registering component to ASoC subsystem via
snd_soc_add_component.
Patchset achieves status quo - behavior of snd_soc_register_component
remains unchanged.
Cezary Rojewski (3):
ASoC: core: Relocate and expose snd_soc_component_initialize
ASoC: core: Simplify snd_soc_component_initialize declaration
ASoC: core: Two step component registration
include/sound/soc-component.h | 3 --
include/sound/soc.h | 11 +++---
sound/soc/soc-component.c | 16 ---------
sound/soc/soc-core.c | 52 +++++++++++++++++----------
sound/soc/soc-generic-dmaengine-pcm.c | 14 +++++---
sound/soc/stm/stm32_adfsdm.c | 9 +++--
6 files changed, 55 insertions(+), 50 deletions(-)
--
2.17.1
Modify snd_soc_add_component so it calls snd_soc_component_initialize
no longer and thus providing true two-step registration. Drivers may
choose to change component's fields before actually adding it to ASoC
subsystem.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20200731144146.6678-4-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move 'name' field initialization responsibility back to
snd_soc_component_initialize to prepare snd_soc_add_component function
for being called separatelly as a second registration step.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20200731144146.6678-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To allow for two-step component registration, expose
snd_soc_component_initialize function and move it back to soc-core.c.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20200731144146.6678-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Enabling a whole subsystem from a single driver 'select' is frowned
upon and won't be accepted in new drivers, that need to use 'depends on'
instead. Existing selection of DMADEVICES will then cause circular
dependencies. Replace them with a dependency.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20200731152433.1297-3-laurent.pinchart@ideasonboard.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The fifo_depth is 64 on i.MX8QM/i.MX8QXP, 128 on i.MX8MQ, 16 on
i.MX7ULP.
Original FSL_SAI_CR1_RFW_MASK value 0x1F is not suitable for
these platform, the FIFO watermark mask should be updated
according to the fifo_depth.
Fixes: a860fac420 ("ASoC: fsl_sai: Add support for imx7ulp/imx8mq")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/1596176895-28724-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit b73287f0b0 ("ASoC: soc-pcm: dpcm: fix playback/capture checks")
changed the meaning of dpcm_playback/dpcm_capture and now requires the
CPU DAI BE to aligned with those flags.
This broke all Amlogic cards with uni-directional backends (All gx and
most axg cards).
While I'm still confused as to how this change is an improvement, those
cards can't remain broken forever. Hopefully, next time an API change is
done like that, all the users will be updated as part of the change, and
not left to fend for themselves.
Fixes: b73287f0b0 ("ASoC: soc-pcm: dpcm: fix playback/capture checks")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200731120603.2243261-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Previous updates to set dailink capabilities and check dailink
capabilities were based on a flawed assumption that all dais support
the same capabilities as the dailink. This is true for TDM
configurations but existing configurations use an amplifier and a
capture device on the same dailink, and the tests would prevent the
card from probing.
This patch modifies the snd_soc_dai_link_set_capabilities()
helper so that the dpcm_playback (resp. dpcm_capture) dailink
capabilities are set if at least one dai supports playback (resp. capture).
Likewise the checks are modified so that an error is reported only
when dpcm_playback (resp. dpcm_capture) is set but none of the CPU
DAIs support playback (resp. capture).
Fixes: 25612477d2 ('ASoC: soc-dai: set dai_link dpcm_ flags with a helper')
Fixes: b73287f0b0 ('ASoC: soc-pcm: dpcm: fix playback/capture checks')
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200723180533.220312-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The various list iterators are able to handle an empty list.
The only effect of avoiding the loop is not initializing some
index variables.
Drop list_empty tests in cases where these variables are not
used.
The semantic patch that makes these changes is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@
expression x,e;
iterator name list_for_each_entry;
statement S;
identifier i;
@@
-if (!(list_empty(x))) {
list_for_each_entry(i,x,...) S
- }
... when != i
? i = e
@@
expression x,e;
iterator name list_for_each_entry_safe;
statement S;
identifier i,j;
@@
-if (!(list_empty(x))) {
list_for_each_entry_safe(i,j,x,...) S
- }
... when != i
when != j
(
i = e;
|
? j = e;
)
@@
expression x,e;
iterator name list_for_each;
statement S;
identifier i;
@@
-if (!(list_empty(x))) {
list_for_each(i,x) S
- }
... when != i
? i = e
@@
expression x,e;
iterator name list_for_each_safe;
statement S;
identifier i,j;
@@
-if (!(list_empty(x))) {
list_for_each_safe(i,j,x) S
- }
... when != i
when != j
(
i = e;
|
? j = e;
)
// -------------------
@@
expression x,e;
statement S;
identifier i;
@@
-if (!(list_empty(x)))
list_for_each_entry(i,x,...) S
... when != i
? i = e
@@
expression x,e;
statement S;
identifier i,j;
@@
-if (!(list_empty(x)))
list_for_each_entry_safe(i,j,x,...) S
... when != i
when != j
(
i = e;
|
? j = e;
)
@@
expression x,e;
statement S;
identifier i;
@@
-if (!(list_empty(x)))
list_for_each(i,x) S
... when != i
? i = e
@@
expression x,e;
statement S;
identifier i,j;
@@
-if (!(list_empty(x)))
list_for_each_safe(i,j,x) S
... when != i
when != j
(
i = e;
|
? j = e;
)
</smpl>
---
drivers/media/pci/saa7134/saa7134-core.c | 14 ++---
drivers/media/usb/cx231xx/cx231xx-core.c | 16 ++----
drivers/media/usb/tm6000/tm6000-core.c | 24 +++-------
drivers/net/ethernet/mellanox/mlx5/core/steering/dr_matcher.c | 13 ++---
drivers/net/ethernet/mellanox/mlx5/core/steering/dr_rule.c | 5 --
drivers/net/ethernet/sfc/ptp.c | 20 +++-----
drivers/net/wireless/ath/dfs_pattern_detector.c | 15 ++----
sound/soc/intel/atom/sst/sst_loader.c | 10 +---
sound/soc/intel/skylake/skl-pcm.c | 8 +--
sound/soc/intel/skylake/skl-topology.c | 5 --
10 files changed, 53 insertions(+), 77 deletions(-)
PulseAudio (and perhaps other userspace utilities) can not detect any
jack for rk3399_gru_sound as the driver doesn't expose related Jack
kcontrols.
This patch adds two DAPM pins to the headset jack, where the
snd_soc_card_jack_new() call automatically creates "Headphones Jack" and
"Headset Mic Jack" kcontrols from them.
With an appropriate ALSA UCM config specifying JackControl fields for
the "Headphones" and "Headset" (mic) devices, PulseAudio can detect
plug/unplug events for both of them after this patch.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Link: https://lore.kernel.org/r/20200721182709.6895-1-alpernebiyasak@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the WM8962 datasheet, there is no register at address 0x200.
WM8962_GPIO_BASE is just a base address for the GPIO registers and not a
real register, so remove it from wm8962_readable_register().
Also, Register 515 (WM8962_GPIO_BASE + 3) does not exist, so skip
its access.
This fixes the following errors:
wm8962 0-001a: ASoC: error at soc_component_read_no_lock on wm8962.0-001a: -16
wm8962 0-001a: ASoC: error at soc_component_read_no_lock on wm8962.0-001a: -16
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200717135959.19212-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use resource_size rather than a verbose computation on
the end and start fields.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@ struct resource ptr; @@
- (ptr.end - ptr.start + 1)
+ resource_size(&ptr)
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1595751933-4952-1-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
list_for_each_entry_safe is able to handle an empty list.
The only effect of avoiding the loop is not initializing the
index variable.
Drop list_empty tests in cases where these variables are not
used.
Note that list_for_each_entry_safe is defined in terms of
list_first_entry, which indicates that it should not be used on an
empty list. But in list_for_each_entry_safe, the element obtained by
list_first_entry is not really accessed, only the address of its
list_head field is compared to the address of the list head, so the
list_first_entry is safe.
The semantic patch that makes this change is as follows (with another
variant for the no brace case): (http://coccinelle.lip6.fr/)
<smpl>
@@
expression x,e;
iterator name list_for_each_entry_safe;
statement S;
identifier i,j;
@@
-if (!(list_empty(x))) {
list_for_each_entry_safe(i,j,x,...) S
- }
... when != i
when != j
(
i = e;
|
? j = e;
)
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1595761112-11003-2-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Passing specific snd_soc_card structure depending on the ACPI ID.
In future we can add other IDs in the ACPI table and pass the structure.
Signed-off-by: Ravulapati Vishnu vardhan rao <Vishnuvardhanrao.Ravulapati@amd.com>
Link: https://lore.kernel.org/r/20200728160255.31020-3-Vishnuvardhanrao.Ravulapati@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As in future our machine driver supports multiple codecs
So changing naming convention of snd_soc_card struct and its fields.
Signed-off-by: Ravulapati Vishnu vardhan rao <Vishnuvardhanrao.Ravulapati@amd.com>
Link: https://lore.kernel.org/r/20200728160255.31020-2-Vishnuvardhanrao.Ravulapati@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for voice and BT calls, along with standard
audio output via the speaker, earpiece, headphone jack, HDMI, and
any accessories compatible with Midas boards. This patch also supports
headphone/headset detection and headsets with inline buttons.
[m.szyprowski: adaptation to v5.1+ kernels (DAI links initialization)]
[s.nawrocki: removal of the clk API calls for CODEC MCLK, the jack data
structure moved to struct midas_priv, coding style and typo fixes,
conversion to new cpu/codec/dai-node binding]
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200728131111.14334-2-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Reset the device before programming the registers or all programming
will be lost as the device resets registers to default settings.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200730142419.28205-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The header was updated to align with the data sheet to start the GPO_CFG
at GPO_CFG0. The code was not updated to the change and therefore the
GPO_CFG0 register was not written to.
Fixes: 6617cff6a0 ("ASoC: tlv320adcx140: Add GPO configuration and drive output config")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200730142419.28205-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
All channels are enabled at boot up, this patch ensures that all
channels are disabled at boot and whenever the function is called.
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Reviewed-by: Sia Jee Heng <jee.heng.sia@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200730055319.1522-3-michael.wei.hong.sit@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable 8kHz audio support for Intel Keem Bay platform.
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Reviewed-by: Sia Jee Heng <jee.heng.sia@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200730055319.1522-2-michael.wei.hong.sit@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The allocation order of things in soc_new_pcm_runtime was changed to
move the device_register before the allocation of the rtd structure.
This was to allow the rtd allocation to be managed by devm. However
currently the sysfs entries are added by device_register and their
visibility depends on variables within the rtd structure, this causes
the pmdown_time and dapm_widgets sysfs entries to be missing for all
rtds.
Correct this issue by manually calling device_add_groups after the
appropriate information is available.
Fixes: d918a37610 ("ASoC: soc-core: tidyup soc_new_pcm_runtime() alloc order")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200730120715.637-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Standard dai format property don't need the "amlogic," prefix.
There nothing amlogic specific about them. Just remove it.
Fixes: 435857e015 ("ASoC: meson: align axg card driver with DT bindings documentation")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200729154456.1983396-5-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
