This patch adds a driver for Microchips CAP1106, an I2C driven, 6-channel
capacitive touch sensor.
For now, only the capacitive buttons are supported, and no specific
settings that can be tweaked for individual channels, except for the
device-wide sensitivity gain. The defaults seem to work just fine out of
the box, so I'll leave configurable parameters for someone who's in need
of them and who can actually measure the impact. All registers are
prepared, however. Many of them are just not used for now.
The implementation does not make any attempt to be compatible to platform
data driven boards, but fully depends on CONFIG_OF.
Power management functions are also left for volounteers with the ability
to actually test them.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix checkpatch warning:
"WARNING: debugfs_remove_recursive(NULL) is safe this check is probably not required"
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's start checking return value of regulator_enable and pwm_enable to
avoid errors. Fixes the following warning:
drivers/input/misc/max8997_haptic.c:185:19: warning: ignoring return value of ‘regulator_enable’, declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchpad on the GIGABYTE U2442 not only stops communicating when we try
to set bit 3 (enable real hardware resolution) of reg_10, but on some BIOS
versions also when we set bit 1 (enable two finger mode auto correct).
I've asked the original reporter of:
https://bugzilla.kernel.org/show_bug.cgi?id=61151
To check that not setting bit 1 does not lead to any adverse effects on his
model / BIOS revision, and it does not, so this commit fixes the touchpad
not working on these versions by simply never setting bit 1 for laptop
models with the no_hw_res quirk.
Reported-and-tested-by: James Lademann <jwlademann@gmail.com>
Tested-by: Philipp Wolfer <ph.wolfer@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
At least the Dell Vostro 5470 elantech *clickpad* reports right button
clicks when clicked in the right bottom area:
https://bugzilla.redhat.com/show_bug.cgi?id=1103528
This is different from how (elantech) clickpads normally operate, normally
no matter where the user clicks on the pad the pad always reports a left
button event, since there is only 1 hardware button beneath the path.
It looks like Dell has put 2 buttons under the pad, one under each bottom
corner, causing this.
Since this however still clearly is a real clickpad hardware-wise, we still
want to report it as such to userspace, so that things like finger movement
in the bottom area can be properly ignored as it should be on clickpads.
So deal with this weirdness by simply mapping a right click to a left click
on elantech clickpads. As an added advantage this is something which we can
simply do on all elantech clickpads, so no need to add special quirks for
this weird model.
Reported-and-tested-by: Elder Marco <eldermarco@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver sends 3 bytes instead of 2 when accessing a register on the M09
firmware, so writing to gain seems to overflow into the offset register.
Signed-off-by: Robert Woerle <robert@linuxdevelopment.de>
Acked-By: Simon Budig <simon.budig@kernelconcepts.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is unused since all users (OMAP4/5) are DT only.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This has been unused since omap4 board files went away.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
New Cintiq tablets have a 200 tablet counts outside of screen area.
Add x/y_min for ABS_X/Y to pass this information to userland.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds support for the tsc2005 touchscreen
to the Nokia N900 DTS file.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds DT support to the tsc2005 touchscreen driver. It also adds
regulator support to the driver if booted via DT.
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add common DT binding documentation for touchscreen devices and
implement input_parse_touchscreen_of_params, which parses the common
properties and configures the input device accordingly.
The method currently does not interpret the axis inversion properties,
since there is no matching flag in the generic linux input device.
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify error
handling and allows us to get rid of da9034_touch_remove().
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fix a typo error in MELFAS MCS-5000 controller driver.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fix a typo error in mms114 touchscreen driver.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fix a typo error in MELFAS 5000/5080 controller driver.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By reading the touchscreen configuration from the settings that the
maXTouch chip is actually using, we can remove some platform data.
The matrix size is not used for anything, and results in some rather
confusing code to re-read it because it may change when configuration
is downloaded, so don't print it out.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Atmel supplies firmware files in ASCII HEX format (.enc) which must be
converted before they can be loaded by kernel driver. Try to detect
the error and print a friendly error message rather than feeding junk
to the bootloader.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By implementing a frame counter, print out fewer debug messages (the
firmware may contain hundreds of frames).
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Move bootloaders reads/writes into separate functions. Instead of switching
client->addr, define new field bootloader_addr in mxt_data. Implement
lookup calculation for bootloader addresses.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The configuration is stored in NVRAM on the maXTouch chip. When the device
is reset it reports a CRC of the stored configuration values. Therefore it
isn't necessary to send the configuration on each probe - we can check the
CRC matches and avoid a timeconsuming backup/reset cycle.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The delay before the chip can be accessed after reset varies between
different chips in maXTouch family. Waiting for an interrupt and a T6
status message with the RESET bit set is a better behaviour.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rather than msleep for MXT_RESET_TIME and MXT_FWRESET_TIME during the
transition to bootloader mode and the transition back from app, wait for
the CHG assert to indicate that the transition is done.
This change replaces the msleep with a wait for completion that the
mxt_interrupt handler signals.
Also add CHG poll after last firmware frame - some bootloader versions will
assert the interrupt line after the final frame, in testing this meant that
the driver attempts to read the info block too early whilst the chip is
still resetting.
This improves firmware update time as we no longer wait longer than
necessary for each reset.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver should not immediately read bootloader status when in
Application Update Mode. The CHG line will assert when the device has made
a state transition and is ready to report a new status via i2c.
This change adds a wait for completion in mxt_check_bootloader, and changes
the mxt_interrupt handler to signal the completion.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These two object table entry fields are reported 1 less than their value.
When used, however, we always want the actual size and instances.
To keep the object size and instances 1-byte fields, and thus preserve
the object-table struct's 6-byte packed alignment, add some convenient
accessor functions that do the +1 every time these fields are accessed.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* The mapping of the GPIO numbers into the T19 status byte varies between
different maXTouch chips. Some have up to 7 GPIOs. Allowing a keycode array
of up to 8 items is simpler and more generic. So replace #define with
configurable number of keys which also allows the removal of is_tp.
* Rename platform data parameters to include "t19" to prevent confusion with
T15 key array.
* Probe aborts early on when pdata is NULL, so no need to check.
* Move "int i" to beginning of function (mixed declarations and code)
* Use API calls rather than __set_bit()
* Remove unused dev variable.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is not necessary to download these values to the maXTouch chip on every
probe, since they are stored in NVRAM. It makes life difficult when tuning
the device to keep them in sync with the config array/file, and requires a
new kernel build for minor tweaks.
These parameters only represent a tiny subset of the available
configuration options, tracking all of these options in platform data would
be a endless task. In addition, different versions of maXTouch chips may
have these values in different places or may not even have them at all.
Having these values also makes life more complex for device tree and other
platforms where having to define a static configuration isn't helpful.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Improve the suspend and resume handlers to allow the device
to wakeup the system from suspend.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Get rid of the attb_read_val() platform hook. Instead, read the ATTB gpio
directly from the driver.
Fail if valid ATTB gpio is not provided by patform data.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Introduce helper functions to configure power and interrupt registers.
Default to IDLE mode on probe as device supports auto wakeup to ACVIE mode
on detecting finger touch.
Configure interrupt mode and polarity on start up. Power down on device
closure or module removal.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
