This makes this code common to both the nv04 and nv50 paths.
For the moment, we keep the previous behaviour with HDMI/eDP connectors
and report them as DVI-D/DP instead. This will be fixed once the rest
of the code has been fixed to deal with those types.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Found by sparse.
Signed-off-by: Luca Barbieri <luca@luca-barbieri.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
i2c_entries seems to be the number of i2c entries,
so with index equal to this number, we could read
invalid data from i2ctable. Fix it.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
get_tmds_index_reg reads some value from stack when mlv happens
to be equal to size of pramdac_table array. Fix it.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This commit breaks the userspace interface, and requires a new libdrm for
nouveau to operate again.
The multiple GEM_PUSHBUF ioctls that were present in 0.0.15 for
compatibility purposes are now gone, and replaced with the new ioctl which
allows for multiple push buffers to be submitted (necessary for hw index
buffers in the nv50 3d driver) and relocations to be applied on any buffer.
A number of other ioctls (CARD_INIT, GEM_PIN, GEM_UNPIN) that were needed
for userspace modesetting have also been removed.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
This allows us to submit push buffers from any memtype to the hardware.
We'll need this ability for VRAM index buffers at some point.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
PFIFO on G80 and up has a new mode where the main ring buffer is simply a
ring of pointers to indirect buffers containing the actual command/data
packets. In order to be able to implement index buffers in the 3D driver
we need to be able to submit data-only push buffers right after the cmd
packet header, which is only possible using the new command submission
method.
This commit doesn't make it possible to implement index buffers yet, some
userspace interface changes will be required, but it does allow for
testing/debugging of the hardware-side support in the meantime.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The nv50 pgraph handler (for example) could reenable pgraph fifo access
and that would be bad when pgraph context is being unloaded (we need the
guarantee a ctxprog isn't running).
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This also modifies the unused PRAMIN PT entries to be all zeroes, can't
really recall why I used 9/0 initially, just that it didn't work for
some reason. It was likely masking a bug elsewhere that's since been
fixed.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This commit changes nouveau to construct PTEs which look very much like
the ones the binary driver creates.
I presume that filling multiple PTEs identically with length flags and
the physical address of the start of a block of VRAM is a hint to the
memory controller that it need not perform additional page table lookups
for that range of addresses.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Unset the bit that indicates that a ctxprog can continue at the end.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
ramfc is zero'ed upon destruction, so it's safer to do things in the right
order.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
- We need to disable pgraph fifo access before checking the current channel,
otherwise we could still hit a running ctxprog.
- The writes to 0x400500 are already handled by pgraph->fifo_access and are
therefore redundant, moreover pgraph fifo access should not be reenabled
before current context is set as invalid. So remove them altogether.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
- In the current situation the padding that is added is dangerous to write
to, userspace could potentially overwrite parts of another bo.
- Depth and stencil buffers are supposed to be large enough in general so
the waste of memory should be acceptable.
- Alternatives are hiding the padding from users or splitting vram into 2
zones.
Signed-off-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes DVI+VGA on my 9400, and likely a lot of other configurations that
got broken by the previos DVI-over-DP fix.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
With DVI and DP plugged, the DVI clock change interrupts being run can
cause DP link training to fail. This adds a spinlock around init table
parsing to prevent this.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It appears we aren't required to do memory sizing ourselves on nv40
either. NV40 init tables read a strap from PEXTDEV_BOOT_0 into a
CRTC register, and then later use that value to select a memory
configuration (written to PFB_CFG0, just like INIT_COMPUTE_MEM on
earlier cards) with INIT_IO_RESTRICT_PROG.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We used single shared fbops struct and patched it at fb init time with
pointers to the right variant. On mixed multicard, this meant that
it was either sending NV50-style commands to all cards, or NV04-style
commands to all cards.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Test the just-allocated value for NULL rather than some other value.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,y;
statement S;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
(
if ((x) == NULL) S
|
if (
- y
+ x
== NULL)
S
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: David Airlie <airlied@linux.ie>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nouveau_gem_ioctl_cpu_prep calls ttm_bo_wait without the bo lock held.
ttm_bo_wait unlocks that lock, and so must be called with it held.
Currently this bug causes libdrm nouveau_bo_busy() to hang the machine.
Signed-off-by: Luca Barbieri <luca at luca-barbieri.com>
Acked-by: Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Apparently, they generate a PFIFO interrupt each time one of the
semaphore methods is executed if its ctxdma wasn't manually marked as
valid. This patch makes it flip the valid bit in response to the
DMA_SEMAPHORE method (which triggers the IRQ even for a valid ctxdma).
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On nv50, this will be needed by applications using CUDA to know
how much stack/local memory to allocate.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
noaccel=1 disables all acceleration and doesn't even attempt
initialising PGRAPH+PFIFO, nofbaccel=1 only makes fbcon unaccelerated.
Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Due to a thinko, these were previously forced to VRAM even if we allocated
them in GART.
This commit fixes that bug, but keeps the previous behaviour of using VRAM
by default until it's been tested properly across more chipsets.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Another hack because of us exposing each encoder block's function as
an encoder rather than exposing a single encoder that deals with them
all.
A proper fix will come, it's just rather invasive so this hack will
do until then.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We need to add the buffer to the list even if we fail, otherwise the
validate_fini() call won't unreserve + unreference the GEM object,
making TTM very unhappy.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Also adds a module option to ignore the status reported via ACPI, in case
we hit systems with broken ACPI.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On most cards the DisplayPort connector is created with 2 encoders sharing
a single SOR (for native DP, and for DVI-over-DP). The previous logic
for turning off unused encoders didn't take into account that we could
have multiple drm_encoders on a single hw encoder and ended up turning off
encoders that were actually being used still.
This patch fixes that issue. We probably want to look at something a bit
better later on, and only expose one drm_encoder per hw encoder block.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
