With the dawn of MMIO gpio-regmap users, it is desirable to let
gpio-regmap ask the regmap if it might sleep during an access so
it can pass that information to gpiochip. Add a new regmap_might_sleep()
to query the regmap.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20221121150843.1562603-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit faa87ce919 ("regmap-irq: Introduce config registers for irq
types") added the num_config_regs, then commit 9edd4f5aee ("regmap-irq:
Deprecate type registers and virtual registers") suggested to replace
num_type_reg with it. However, regmap_add_irq_chip_fwnode wasn't modified
to use the new property. Later on, commit 255a03bb1b ("ASoC: wcd9335:
Convert irq chip to config regs") removed the old num_type_reg property
from the WCD9335 driver's struct regmap_irq_chip, causing a null pointer
dereference in regmap_irq_set_type when it tried to index d->type_buf as
it was never allocated in regmap_add_irq_chip_fwnode:
[ 39.199374] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
[ 39.200006] Call trace:
[ 39.200014] regmap_irq_set_type+0x84/0x1c0
[ 39.200026] __irq_set_trigger+0x60/0x1c0
[ 39.200040] __setup_irq+0x2f4/0x78c
[ 39.200051] request_threaded_irq+0xe8/0x1a0
Use num_config_regs in regmap_add_irq_chip_fwnode instead of num_type_reg,
and fall back to it if num_config_regs isn't defined to maintain backward
compatibility.
Fixes: faa87ce919 ("regmap-irq: Introduce config registers for irq types")
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Link: https://lore.kernel.org/r/20221107202114.823975-1-y.oudjana@protonmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This has been a busy release for regmap with one thing and other,
there's been an especially large interest in MMIO regmaps for some
reason. The bulk of the changes are cleanups but there are several user
visible changes too:
- Support for I/O ports in regmap-mmio.
- Support for accelerated noinc operations in regmap-mmio.
- Support for tracing the register values in bulk operations.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmM6sskACgkQJNaLcl1U
h9Bj1Qf+PLNz4gQq7ki06KI6+Liz6daN5j/bfUGSizx6rns5qOZxt1A/CwDFM5ZR
6aY+tGL4ksYfEUEZHsr7qaQKptWoLmwDVX0oYZqHdBf4Wf7I6iht8WCq68KwDCzz
zQoswzoLmVuRd6aplFifEF3SOqjBrTQO3gkXBteIeA6/i1pwO9wOJdM4ZU54FX+Q
zexv7H/E9uKVonrViBMLPczaPhge4+ILNEDekSUW4AZ0RmUZ6JjW3aOZbwR6ut1x
7bS3ric9xGhW4IQdOZISY+ARhPPworcgdK5GoqBfjWV2vYc0c1iCawvF73Wm/NJC
GMGc5FIBi3a82oCMmSR1dAcci9CRLw==
=TTeQ
-----END PGP SIGNATURE-----
Merge tag 'regmap-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This has been a busy release for regmap with one thing and other,
there's been an especially large interest in MMIO regmaps for some
reason. The bulk of the changes are cleanups but there are several
user visible changes too:
- Support for I/O ports in regmap-mmio
- Support for accelerated noinc operations in regmap-mmio
- Support for tracing the register values in bulk operations"
* tag 'regmap-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: mmio: replace return 0 with break in switch statement
regmap: spi-avmm: Use swabXX_array() helpers
regmap: mmio: Use swabXX_array() helpers
swab: Add array operations
regmap: trace: Remove unneeded blank lines
regmap: trace: Remove explicit castings
regmap: trace: Remove useless check for NULL for bulk ops
regmap: mmio: Fix rebase error
regmap: check right noinc bounds in debug print
regmap: introduce value tracing for regmap bulk operations
regmap/hexagon: Properly fix the generic IO helpers
regmap: mmio: Support accelerared noinc operations
regmap: Support accelerated noinc operations
regmap: Make use of get_unaligned_be24(), put_unaligned_be24()
regmap: mmio: Fix MMIO accessors to avoid talking to IO port
regmap: mmio: Introduce IO accessors that can talk to IO port
regmap: mmio: Get rid of broken 64-bit IO
regmap: mmio: Remove mmio_relaxed member from context
Variable min_stride is assigned a value that is never read, fix this by
replacing the return 0 with a break statement. This also makes the case
statement consistent with the other cases in the switch statement.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220922080445.818020-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we have a few helpers to swab elements of a given size in an array
use them instead of open coded variants.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220831212744.56435-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we have a few helpers to swab elements of a given size in an array
use them instead of open coded variants.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220831212744.56435-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a few unneeded blank lines in some of event definitions,
remove them in order to make those definitions consistent with
the rest.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220901132336.33234-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to have explicit castings to the same type the
variables are of. Remove the explicit castings.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Link: https://lore.kernel.org/r/20220901132336.33234-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If the buffer pointer is NULL we already are in troubles since
regmap bulk API expects caller to provide valid parameters,
it dereferences that without any checks before we call for
traces.
Moreover, the current code will print garbage in the case of
buffer is NULL and length is not 0.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220901132336.33234-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A dangling pointless "ret 0" was left in and some unneeded
whitespace can go too.
Fixes: 81c0386c13 ("regmap: mmio: Support accelerared noinc operations")
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220831141303.501548-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We were using the wrong bound in the debug prints: this
needs to be the number of elements, not the number of bytes,
since we're indexing into an element-size typed array.
Fixes: c20cc099b3 ("regmap: Support accelerated noinc operations")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220823135700.265019-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, only one-register io operations support tracepoints with
value logging. For the regmap bulk operations developer can view
hw_start/hw_done tracepoints with starting reg number and registers
count to be reading or writing. This patch injects tracepoints with
dumping registers values in the hex format to regmap bulk reading
and writing.
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Link: https://lore.kernel.org/r/20220816181451.5628-1-ddrokosov@sberdevices.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the max_raw_read and max_raw_write limits in regmap_spi struct
do not take into account the additional size of the transmitted register
address and padding. This may result in exceeding the maximum permitted
SPI message size, which could cause undefined behaviour, e.g. data
corruption.
Fix regmap_get_spi_bus() to properly adjust the above mentioned limits
by reserving space for the register address/padding as set in the regmap
configuration.
Fixes: f231ff38b7 ("regmap: spi: Set regmap max raw r/w from max_transfer_size")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220818104851.429479-1-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the newly added callback for accelerated noinc MMIO
to provide writesb, writesw, writesl, writesq, readsb, readsw,
readsl and readsq.
A special quirk is needed to deal with big endian regmaps: there
are no accelerated operations defined for big endian, so fall
back to calling the big endian operations itereatively for this
case.
The Hexagon architecture turns out to have an incomplete
<asm/io.h>: writesb() is not implemented. Fix this by doing
what other architectures do: include <asm-generic/io.h> into
the <asm/io.h> file.
Cc: Brian Cain <bcain@quicinc.com>
Cc: linux-hexagon@vger.kernel.org
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220816204832.265837-2-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Several architectures have accelerated operations for MMIO
operations writing to a single register, such as writesb, writesw,
writesl, writesq, readsb, readsw, readsl and readsq but regmap
currently cannot use them because we have no hooks for providing
an accelerated noinc back-end for MMIO.
Solve this by providing reg_[read/write]_noinc callbacks for
the bus abstraction, so that the regmap-mmio bus can use this.
Currently I do not see a need to support this for custom regmaps
so it is only added to the bus.
Callbacks are passed a void * with the array of values and a
count which is the number of items of the byte chunk size for
the specific register width.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220816204832.265837-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Andy Shevchenko <andriy.shevchenko@linux.intel.com>:
Currently regmap MMIO doesn't support IO ports, while being inconsistent
in used IO accessors. Fix the latter and extend framework with the
former.
Since we have a proper endianness converters for BE 24-bit data use
them. While at it, format the code using switch-cases as it's done
for the rest of the endianness handlers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220726151213.71712-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently regmap MMIO is inconsistent with IO accessors. I.e.
the Big Endian counterparts are using ioreadXXbe() / iowriteXXbe()
which are not clean implementations of readXXbe().
That said, reimplement current Big Endian MMIO accessors by replacing
ioread()/iowrite() with respective read()/write() and swab() calls.
Note, there are no current in-kernel users that may utilize the
functionality of the IO ports on Big Endian hardware. All drivers
that use regmap MMIO either Little Endian, or they don't map IO
ports in a way that ioreadXX()/iowriteXX() may be utilized.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/20220808203401.35153-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some users may use regmap MMIO for IO ports, and this can be done
by assigning ioreadXX()/iowriteXX() and their Big Endian counterparts
to the regmap context.
Add IO port support with a corresponding flag added.
While doing that, make sure that user won't select relaxed MMIO access
along with IO port because the latter have no relaxed variants.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/20220808203401.35153-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current implementation, besides having no active users, is broken
by design of regmap. For 64-bit IO we need to supply 64-bit value,
otherwise there is no way to handle upper 32 bits in 64-bit register.
Hence, remove the broken IO accessors for good and wait for real user
that can fix entire regmap API for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/20220808203401.35153-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to keep mmio_relaxed member in the context, it's
onetime used during generation of the context. Remove it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: William Breathitt Gray <william.gray@linaro.org>
Link: https://lore.kernel.org/r/20220808203401.35153-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A regmap may still require to set a custom reg_update_bits instead of
relying to the regmap_bus_read/write general function.
Permit to set it in the map if provided by the regmap config.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220715201032.19507-1-ansuelsmth@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In regmap_field_init() when a invalid mask is provided it still
initializes with any warnings.
An example of this is when the LSB is greater than MSB a mask of zero
is produced.
WARN_ONCE() is not ideal for this but requires less changes to core regmap
code.
Cc: Mark Brown <broonie@kernel.org>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Link: https://lore.kernel.org/r/20220708013125.313892-1-mranostay@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
irq_reg_stride in struct regmap_irq_chip is often 0, but that
actually means to use the default stride of 1. The effective
stride is stored in struct regmap_irq_chip_data->irq_reg_stride
and will get the corrected default value.
The default ->get_irq_reg() callback was using the stride from
the chip definition, which is wrong; fix it to use the effective
stride from the chip data instead.
Link: https://lore.kernel.org/lkml/acaaf77f-3282-8544-dd3c-7915fc1a6a4f@samsung.com/
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220704112847.23844-1-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Aidan MacDonald <aidanmacdonald.0x0@gmail.com>:
This series is an attempt at cleaning up the regmap-irq API in order
to simplify things and consolidate existing features, while at the
same time generalizing it to support a wider range of hardware.
There is a new system for IRQ type configuration, some tweaks to
unmask registers so they're more intuitive and useful, and a new
callback for calculating register addresses. There's also a few
minor code cleanups in here.
In v2 I've taken the approach of adding new features and deprecating
existing ones rather than removing them aggressively. Warnings will
be issued for any drivers that use deprecated features, but they'll
otherwise continue to function normally.
One important caveat: not all of these changes are tested beyond
compile testing, since I don't have hardware to exercise all of
the features.
When num_reg_defaults > 0 but reg_defaults is NULL, there will be a
NULL pointer exception.
Current code has no such usage, but as additional hardening, also
check this to prevent any chance of crashing.
Signed-off-by: Schspa Shi <schspa@gmail.com>
Link: https://lore.kernel.org/r/20220629130951.63040-1-schspa@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This flag is a bit of a hack and the same thing can be accomplished
using a custom ->get_irq_reg() callback. Add a warning to catch any
use of the flag.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-13-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace the internal sub_irq_reg() function with a public callback
that drivers can use when they have more complex register layouts.
The default implementation is regmap_irq_get_irq_reg_linear(), used
if the chip doesn't provide its own callback.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-12-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To me "unmask" suggests that we write 1s to the register when
an interrupt is enabled. This also makes sense because it's the
opposite of what the "mask" register does (write 1s to disable
an interrupt).
But regmap-irq does the opposite: for a disabled interrupt, it
writes 1s to "unmask" and 0s to "mask". This is surprising and
deviates from the usual way mask registers are handled.
Additionally, mask_invert didn't interact with unmask registers
properly -- it caused them to be ignored entirely.
Fix this by making mask and unmask registers orthogonal, using
the following behavior:
* Mask registers are written with 1s for disabled interrupts.
* Unmask registers are written with 1s for enabled interrupts.
This behavior supports both normal or inverted mask registers
and separate set/clear registers via different combinations of
mask_base/unmask_base.
The old unmask register behavior is deprecated. Drivers need to
opt-in to the new behavior by setting mask_unmask_non_inverted.
Warnings are issued if the driver relies on deprecated behavior.
Chips that only set one of mask_base/unmask_base don't have to
use the mask_unmask_non_inverted flag because that use case was
previously not supported.
The mask_invert flag is also deprecated in favor of describing
inverted mask registers as unmask registers.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-11-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Config registers can be used to replace both type and virtual
registers, so mark both features are deprecated and issue a
warning if they're used.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-10-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Config registers provide a more uniform approach to handling irq type
registers. They are essentially an extension of the virtual registers
used by the qcom-pm8008 driver.
Config registers can be represented as a 2D array:
config_base[0] reg0,0 reg0,1 reg0,2 reg0,3
config_base[1] reg1,0 reg1,1 reg1,2 reg1,3
config_base[2] reg2,0 reg2,1 reg2,2 reg2,3
There are 'num_config_bases' base registers, each of which is used to
address 'num_config_regs' registers. The addresses are calculated in
the same way as for other bases. It is assumed that an irq's type is
controlled by one column of registers; that column is identified by
the irq's 'type_reg_offset'.
The set_type_config() callback is responsible for updating the config
register contents. It receives an array of buffers (each represents a
row of registers) and the index of the column to update, along with
the 'struct regmap_irq' description and requested irq type.
Buffered values are written to registers in regmap_irq_sync_unlock().
Note that the entire register contents are overwritten, which is a
minor change in behavior from type registers via 'type_base'.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-9-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are several conditions that must be satisfied to support
bulk read of status registers. Move the check into a function
to avoid duplicating it in two places.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-8-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a71411dbf6 ("regmap: irq: add chip option mask_writeonly")
introduced the mask_writeonly option, but it isn't used now and it
appears it's never been used by any in-tree drivers. The motivation
for the option is mentioned in the commit message,
Some irq controllers have writeonly/multipurpose register
layouts. In those cases we read invalid data back. [...]
The option causes mask register updates to use regmap_write_bits()
instead of regmap_update_bits().
However, regmap_write_bits() doesn't solve the reading invalid data
problem. It's still a read-modify-write op like regmap_update_bits().
The difference is that 'update bits' will only write the new value
if it is different from the current value, while 'write bits' will
write the new value unconditionally, even if it's the same as the
current value.
This seems like a bit of a specialized use case and probably isn't
that useful for regmap-irq, so let's just remove the option and go
back to using an 'update bits' op for the mask registers. We can
always add the option back if some driver ends up needing it in the
future.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-7-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap_irq_update_bits() is misnamed and should only be used for
updating mask registers, since it checks the mask_writeonly flag.
However, it was also used for updating wake and type registers.
It's safe to replace these uses with regmap_update_bits() because
there are no users of the mask_writeonly flag.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-6-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Check types_supported instead of checking type_rising/falling_val
when using type_in_mask interrupts. This makes the intent clearer
and allows a type_in_mask irq to support level or edge triggers,
rather than only edge triggers.
Update the documentation and comments to reflect the new behavior.
This shouldn't affect existing drivers, because if they didn't
set types_supported properly the type buffer wouldn't be updated.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-5-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of mentioning unsigned int directly, use a sizeof(...)
involving the buffer we're allocating to ensure the types don't
get out of sync.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-4-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It appears that no chip ever required a nonzero type_reg_stride
and commit 1066cfbdfa ("regmap-irq: Extend sub-irq to support
non-fixed reg strides") broke support. Just remove the field.
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220623211420.918875-3-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For devices with no cache it can make sense to use cache only mode as a
mechanism for trapping writes to hardware which is inaccessible but since
no cache is equivalent to cache bypass we force such devices into bypass
mode. This means that our check that bypass and cache only mode aren't both
enabled simultanously is less sensible for devices without a cache so relax
it.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220622171723.1235749-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to divide the sub-irq status register offset by register
stride to get an index for the status buffer to avoid an out of
bounds write when the register stride is greater than 1.
Fixes: a2d21848d9 ("regmap: regmap-irq: Add main status register support")
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220620200644.1961936-3-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When enabling a type_in_mask irq, the type_buf contents must be
AND'd with the mask of the IRQ we're enabling to avoid enabling
other IRQs by accident, which can happen if several type_in_mask
irqs share a mask register.
Fixes: bc998a7303 ("regmap: irq: handle HW using separate rising/falling edge interrupts")
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220620200644.1961936-2-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are some functions that were missed by commit d77e745613 ("regmap:
Add bulk read/write callbacks into regmap_config") when support to define
bulk read/write callbacks in regmap_config was introduced.
The regmap_bulk_write() and regmap_noinc_write() functions weren't changed
to use the added map->write instead of the map->bus->write handler.
Also, the regmap_can_raw_write() was not modified to take map->write into
account. So will only return true if a bus with a .write callback is set.
Fixes: d77e745613 ("regmap: Add bulk read/write callbacks into regmap_config")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220616073435.1988219-4-javierm@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Before adding support to define bulk read/write callbacks in regmap_config
by the commit d77e745613 ("regmap: Add bulk read/write callbacks into
regmap_config"), the regmap_noinc_read() function returned an errno early
a map->bus->read callback wasn't set.
But that commit dropped the check and now a call to _regmap_raw_read() is
attempted even when bulk read operations are not supported. That function
checks for map->read anyways but there's no point to continue if the read
can't succeed.
Also is a fragile assumption to make so is better to make it fail earlier.
Fixes: d77e745613 ("regmap: Add bulk read/write callbacks into regmap_config")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220616073435.1988219-3-javierm@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Support for drivers to define bulk read/write callbacks in regmap_config
was introduced by the commit d77e745613 ("regmap: Add bulk read/write
callbacks into regmap_config"), but this commit wrongly dropped a check
in regmap_bulk_read() to determine whether bulk reads can be done or not.
Before that commit, it was checked if map->bus was set. Now has to check
if a map->read callback has been set.
Fixes: d77e745613 ("regmap: Add bulk read/write callbacks into regmap_config")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20220616073435.1988219-2-javierm@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add simple bit operations for setting, clearing and testing specific
bits with regmap_field.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmKpskgACgkQJNaLcl1U
h9BF7Af7Bg1qhqvTJQKvfc1TU7pRnO2Mt90MJTTAFMgiMP/+FZhiaDrKm12SBTPh
w8Gomg8X+EYVpiqtywFoc0mZIUe03g9+8RpuKyK2EOReaguhU2qHQPDo2Dhx6x5p
VnNY9w/rhQsrX8153c6ICZ8YqrxNqCbgCh7eulMeXz74wbxwbrNdZbbCaM9+WCS/
fTWtNUwZ+3JtaSP55UCX/ITNrLct0gPdWqkRpLExv9HdOf1HaBRUTZH69ftQg82S
PHsxEBpPWKbViflSU7V5/UgeBCTS7FjRpwB6OEX69V+VGhRIey9IgZqbSsX9KoXX
RYPKj5DZD9JtPNA0W5Dzs0KyUIlDtA==
=vniQ
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmKqENwACgkQJNaLcl1U
h9D1pQf/cbMWcZeRe6eRxvDueIhyMYXwhahxEHMCL6EOR5SLLARB40klJq5DDPlM
D7SZlPES1oXXQ8zm8rpBahfQf3AAeiUMZ4+bOMMU45xaNTKeOGPuihiP69PQxzp1
RryrB6/AN+qKepHaWsnhOyarVnJ2XUDJ58QBmYwee5UFdxiPPIzjMLC0FVEgLhIc
Ng75dFIur3SknYyoYyd9gsH/VydlaEiYQ9s3GRKtq+D0P/fbsylPp1w5Lup3tXWh
kGYyJroz9doevY5K+TeMsVqSJhES3VJkz9GVxkdwCB6qhrXzGkbdnU7ZF1MZGlnf
bOC6+lE+CxoDWx/apLmdJg6ZmnHxdQ==
=CWeE
-----END PGP SIGNATURE-----
Merge tag 'regmap-field-bit-helpers' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into regmap-5.20
regmap: Add regmap_field helpers for simple bit operations
Add simple bit operations for setting, clearing and testing specific
bits with regmap_field.
We have set/clear/test operations for regmap, but not for regmap_field yet.
So let's introduce regmap_field helpers too.
In many instances regmap_field_update_bits() is used for simple bit setting
and clearing. In these cases the last argument is redundant and we can
hide it with a static inline function.
This adds three new helpers for simple bit operations: set_bits,
clear_bits and test_bits (the last one defined as a regular function).
Signed-off-by: Li Chen <lchen@ambarella.com>
Link: https://lore.kernel.org/r/180eef422c3.deae9cd960729.8518395646822099769@zohomail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The map->bus can be NULL here, add the missing NULL pointer check.
Fixes: d77e745613 ("regmap: Add bulk read/write callbacks into regmap_config")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Mark Brown <broonie@kernel.org>
To: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20220509003035.225272-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Marek Vasut:
This patch adds an API for custom bulk operations on a simple regmap,
the number of single use bus implementations shows there's a need for
this.
Currently the regmap_config structure only allows the user to implement
single element register read/write using .reg_read/.reg_write callbacks.
The regmap_bus already implements bulk counterparts of both, and is being
misused as a workaround for the missing bulk read/write callbacks in
regmap_config by a couple of drivers. To stop this misuse, add the bulk
read/write callbacks to regmap_config and call them from the regmap core
code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Link: https://lore.kernel.org/r/20220430025145.640305-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Current logic does not consider multi-stride cases,
the max_register have to calculate with reg_stride
because it is a kind of address range.
Signed-off-by: Jeongtae Park <jtp.park@samsung.com>
Link: https://lore.kernel.org/r/20220425114613.15934-1-jtp.park@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The only usage of these is to pass their address to __regmap_init() or
__devm_regmap_init(), both which takes pointers to const struct
regmap_bus. Make them const to allow the compiler to put them in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20220330214110.36337-1-rikard.falkeborn@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of small fixes, plus some new features that enable us to handle
devices that reformat register addresses depending on the bus used to
handle the control interface more gracefully.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmI4aVQACgkQJNaLcl1U
h9DH7Qf/UfcjSp9MbQ7vZ+uuSQFjcRSSKri0VzFSETAaXBSyDOF43L/3dk60xDo5
+4Om4LX3LZvA387I3bctPaij8fNp+X1bYr2pWUbh/FnJ+fS7PUfzXbQXkh/tKsMP
qhYCcrWVBnGTj0OZAuazYW79V1LolBGC5+YjDRipbcwZhqNVWZKuWVYUhLOduZ5G
5n5PxUyPnDEYF6ixJQq2QiCA6Pb/BSPgviaEHVxeLWxs8IOtq+9u69ijecfDYiwD
vMpFlOnPoy+Bpu7gnU2LhDZ/Nmxvi22BtRxt4qtmC3lTq9Cf/Xrtm2En3aaRsero
SsLc0ZaHkt6W9V5O0yFNrjWLslTAJg==
=3oe7
-----END PGP SIGNATURE-----
Merge tag 'regmap-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"A couple of small fixes, plus some new features that enable us to
handle devices that reformat register addresses depending on the bus
used to handle the control interface more gracefully"
* tag 'regmap-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: allow a defined reg_base to be added to every address
regmap: add configurable downshift for addresses
regmap: irq: cleanup comments
regmap-irq: Fix typo in comment
There's an inconsistency that arises when a register set can be accessed
internally via MMIO, or externally via SPI. The VSC7514 chip allows both
modes of operation. When internally accessed, the system utilizes __iomem,
devm_ioremap_resource, and devm_regmap_init_mmio.
For SPI it isn't possible to utilize memory-mapped IO. To properly operate,
the resource base must be added to the register before every operation.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20220313224524.399947-3-colin.foster@in-advantage.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an additional reg_downshift to be applied to register addresses before
any register accesses. An example of a device that uses this is a VSC7514
chip, which require each register address to be downshifted by two if the
access is performed over a SPI bus.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Link: https://lore.kernel.org/r/20220313224524.399947-2-colin.foster@in-advantage.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With the existing logic where clear_ack is true (HW doesn’t support
auto clear for ICR), interrupt clear register reset is not handled
properly. Due to this only the first interrupts get processed properly
and further interrupts are blocked due to not resetting interrupt
clear register.
Example for issue case where Invert_ack is false and clear_ack is true:
Say Default ISR=0x00 & ICR=0x00 and ISR is triggered with 2
interrupts making ISR = 0x11.
Step 1: Say ISR is set 0x11 (store status_buff = ISR). ISR needs to
be cleared with the help of ICR once the Interrupt is processed.
Step 2: Write ICR = 0x11 (status_buff), this will clear the ISR to 0x00.
Step 3: Issue - In the existing code, ICR is written with ICR =
~(status_buff) i.e ICR = 0xEE -> This will block all the interrupts
from raising except for interrupts 0 and 4. So expectation here is to
reset ICR, which will unblock all the interrupts.
if (chip->clear_ack) {
if (chip->ack_invert && !ret)
........
else if (!ret)
ret = regmap_write(map, reg,
~data->status_buf[i]);
So writing 0 and 0xff (when ack_invert is true) should have no effect, other
than clearing the ACKs just set.
Fixes: 3a6f0fb7b8 ("regmap: irq: Add support to clear ack registers")
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220217085007.30218-1-quic_pkumpatl@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is not a resource manager, it is a "Resource managed version of
regmap_add_irq_chip()". Fix the comment.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Link: https://lore.kernel.org/r/20220113144259.355845-1-luca@lucaceresoli.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit cffa4b2122 ("regmap: debugfs: Fix a memory leak when
calling regmap_attach_dev"), the following debugfs error is seen
on i.MX boards:
debugfs: Directory 'dummy-iomuxc-gpr@20e0000' with parent 'regmap' already present!
In the attempt to fix the memory leak, the above commit added a NULL check
for map->debugfs_name. For the first debufs entry, map->debugfs_name is NULL
and then the new name is allocated via kasprintf().
For the second debugfs entry, map->debugfs_name() is no longer NULL, so
it will keep using the old entry name and the duplicate name error is seen.
Quoting Mark Brown:
"That means that if the device gets freed we'll end up with the old debugfs
file hanging around pointing at nothing.
...
To be more explicit this means we need a call to regmap_debugfs_exit()
which will clean up all the existing debugfs stuff before we loose
references to it."
Call regmap_debugfs_exit() prior to regmap_debugfs_init() to fix
the problem.
Tested on i.MX6Q and i.MX6SX boards.
Fixes: cffa4b2122 ("regmap: debugfs: Fix a memory leak when calling regmap_attach_dev")
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20220107163307.335404-1-festevam@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some device requires a special handling for reg_update_bits and can't use
the normal regmap read write logic. An example is when locking is
handled by the device and rmw operations requires to do atomic operations.
Allow to declare a dedicated function in regmap_config for
reg_update_bits in no bus configuration.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20211104150040.1260-1-ansuelsmth@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Remove socket skb caches
- Add a SO_RESERVE_MEM socket op to forward allocate buffer space
and avoid memory accounting overhead on each message sent
- Introduce managed neighbor entries - added by control plane and
resolved by the kernel for use in acceleration paths (BPF / XDP
right now, HW offload users will benefit as well)
- Make neighbor eviction on link down controllable by userspace
to work around WiFi networks with bad roaming implementations
- vrf: Rework interaction with netfilter/conntrack
- fq_codel: implement L4S style ce_threshold_ect1 marking
- sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()
BPF:
- Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
as implemented in LLVM14
- Introduce bpf_get_branch_snapshot() to capture Last Branch Records
- Implement variadic trace_printk helper
- Add a new Bloomfilter map type
- Track <8-byte scalar spill and refill
- Access hw timestamp through BPF's __sk_buff
- Disallow unprivileged BPF by default
- Document BPF licensing
Netfilter:
- Introduce egress hook for looking at raw outgoing packets
- Allow matching on and modifying inner headers / payload data
- Add NFT_META_IFTYPE to match on the interface type either from
ingress or egress
Protocols:
- Multi-Path TCP:
- increase default max additional subflows to 2
- rework forward memory allocation
- add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS
- MCTP flow support allowing lower layer drivers to configure msg
muxing as needed
- Automatic Multicast Tunneling (AMT) driver based on RFC7450
- HSR support the redbox supervision frames (IEC-62439-3:2018)
- Support for the ip6ip6 encapsulation of IOAM
- Netlink interface for CAN-FD's Transmitter Delay Compensation
- Support SMC-Rv2 eliminating the current same-subnet restriction,
by exploiting the UDP encapsulation feature of RoCE adapters
- TLS: add SM4 GCM/CCM crypto support
- Bluetooth: initial support for link quality and audio/codec
offload
Driver APIs:
- Add a batched interface for RX buffer allocation in AF_XDP
buffer pool
- ethtool: Add ability to control transceiver modules' power mode
- phy: Introduce supported interfaces bitmap to express MAC
capabilities and simplify PHY code
- Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks
New drivers:
- WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)
- Ethernet driver for ASIX AX88796C SPI device (x88796c)
Drivers:
- Broadcom PHYs
- support 72165, 7712 16nm PHYs
- support IDDQ-SR for additional power savings
- PHY support for QCA8081, QCA9561 PHYs
- NXP DPAA2: support for IRQ coalescing
- NXP Ethernet (enetc): support for software TCP segmentation
- Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
Gigabit-capable IP found on RZ/G2L SoC
- Intel 100G Ethernet
- support for eswitch offload of TC/OvS flow API, including
offload of GRE, VxLAN, Geneve tunneling
- support application device queues - ability to assign Rx and Tx
queues to application threads
- PTP and PPS (pulse-per-second) extensions
- Broadcom Ethernet (bnxt)
- devlink health reporting and device reload extensions
- Mellanox Ethernet (mlx5)
- offload macvlan interfaces
- support HW offload of TC rules involving OVS internal ports
- support HW-GRO and header/data split
- support application device queues
- Marvell OcteonTx2:
- add XDP support for PF
- add PTP support for VF
- Qualcomm Ethernet switch (qca8k): support for QCA8328
- Realtek Ethernet DSA switch (rtl8366rb)
- support bridge offload
- support STP, fast aging, disabling address learning
- support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch
- Mellanox Ethernet/IB switch (mlxsw)
- multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
- offload root TBF qdisc as port shaper
- support multiple routing interface MAC address prefixes
- support for IP-in-IP with IPv6 underlay
- MediaTek WiFi (mt76)
- mt7921 - ASPM, 6GHz, SDIO and testmode support
- mt7915 - LED and TWT support
- Qualcomm WiFi (ath11k)
- include channel rx and tx time in survey dump statistics
- support for 80P80 and 160 MHz bandwidths
- support channel 2 in 6 GHz band
- spectral scan support for QCN9074
- support for rx decapsulation offload (data frames in 802.3
format)
- Qualcomm phone SoC WiFi (wcn36xx)
- enable Idle Mode Power Save (IMPS) to reduce power consumption
during idle
- Bluetooth driver support for MediaTek MT7922 and MT7921
- Enable support for AOSP Bluetooth extension in Qualcomm WCN399x
and Realtek 8822C/8852A
- Microsoft vNIC driver (mana)
- support hibernation and kexec
- Google vNIC driver (gve)
- support for jumbo frames
- implement Rx page reuse
Refactor:
- Make all writes to netdev->dev_addr go thru helpers, so that we
can add this address to the address rbtree and handle the updates
- Various TCP cleanups and optimizations including improvements
to CPU cache use
- Simplify the gnet_stats, Qdisc stats' handling and remove
qdisc->running sequence counter
- Driver changes and API updates to address devlink locking
deficiencies
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=srde
-----END PGP SIGNATURE-----
Merge tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Remove socket skb caches
- Add a SO_RESERVE_MEM socket op to forward allocate buffer space and
avoid memory accounting overhead on each message sent
- Introduce managed neighbor entries - added by control plane and
resolved by the kernel for use in acceleration paths (BPF / XDP
right now, HW offload users will benefit as well)
- Make neighbor eviction on link down controllable by userspace to
work around WiFi networks with bad roaming implementations
- vrf: Rework interaction with netfilter/conntrack
- fq_codel: implement L4S style ce_threshold_ect1 marking
- sch: Eliminate unnecessary RCU waits in mini_qdisc_pair_swap()
BPF:
- Add support for new btf kind BTF_KIND_TAG, arbitrary type tagging
as implemented in LLVM14
- Introduce bpf_get_branch_snapshot() to capture Last Branch Records
- Implement variadic trace_printk helper
- Add a new Bloomfilter map type
- Track <8-byte scalar spill and refill
- Access hw timestamp through BPF's __sk_buff
- Disallow unprivileged BPF by default
- Document BPF licensing
Netfilter:
- Introduce egress hook for looking at raw outgoing packets
- Allow matching on and modifying inner headers / payload data
- Add NFT_META_IFTYPE to match on the interface type either from
ingress or egress
Protocols:
- Multi-Path TCP:
- increase default max additional subflows to 2
- rework forward memory allocation
- add getsockopts: MPTCP_INFO, MPTCP_TCPINFO, MPTCP_SUBFLOW_ADDRS
- MCTP flow support allowing lower layer drivers to configure msg
muxing as needed
- Automatic Multicast Tunneling (AMT) driver based on RFC7450
- HSR support the redbox supervision frames (IEC-62439-3:2018)
- Support for the ip6ip6 encapsulation of IOAM
- Netlink interface for CAN-FD's Transmitter Delay Compensation
- Support SMC-Rv2 eliminating the current same-subnet restriction, by
exploiting the UDP encapsulation feature of RoCE adapters
- TLS: add SM4 GCM/CCM crypto support
- Bluetooth: initial support for link quality and audio/codec offload
Driver APIs:
- Add a batched interface for RX buffer allocation in AF_XDP buffer
pool
- ethtool: Add ability to control transceiver modules' power mode
- phy: Introduce supported interfaces bitmap to express MAC
capabilities and simplify PHY code
- Drop rtnl_lock from DSA .port_fdb_{add,del} callbacks
New drivers:
- WiFi driver for Realtek 8852AE 802.11ax devices (rtw89)
- Ethernet driver for ASIX AX88796C SPI device (x88796c)
Drivers:
- Broadcom PHYs
- support 72165, 7712 16nm PHYs
- support IDDQ-SR for additional power savings
- PHY support for QCA8081, QCA9561 PHYs
- NXP DPAA2: support for IRQ coalescing
- NXP Ethernet (enetc): support for software TCP segmentation
- Renesas Ethernet (ravb) - support DMAC and EMAC blocks of
Gigabit-capable IP found on RZ/G2L SoC
- Intel 100G Ethernet
- support for eswitch offload of TC/OvS flow API, including
offload of GRE, VxLAN, Geneve tunneling
- support application device queues - ability to assign Rx and Tx
queues to application threads
- PTP and PPS (pulse-per-second) extensions
- Broadcom Ethernet (bnxt)
- devlink health reporting and device reload extensions
- Mellanox Ethernet (mlx5)
- offload macvlan interfaces
- support HW offload of TC rules involving OVS internal ports
- support HW-GRO and header/data split
- support application device queues
- Marvell OcteonTx2:
- add XDP support for PF
- add PTP support for VF
- Qualcomm Ethernet switch (qca8k): support for QCA8328
- Realtek Ethernet DSA switch (rtl8366rb)
- support bridge offload
- support STP, fast aging, disabling address learning
- support for Realtek RTL8365MB-VC, a 4+1 port 10M/100M/1GE switch
- Mellanox Ethernet/IB switch (mlxsw)
- multi-level qdisc hierarchy offload (e.g. RED, prio and shaping)
- offload root TBF qdisc as port shaper
- support multiple routing interface MAC address prefixes
- support for IP-in-IP with IPv6 underlay
- MediaTek WiFi (mt76)
- mt7921 - ASPM, 6GHz, SDIO and testmode support
- mt7915 - LED and TWT support
- Qualcomm WiFi (ath11k)
- include channel rx and tx time in survey dump statistics
- support for 80P80 and 160 MHz bandwidths
- support channel 2 in 6 GHz band
- spectral scan support for QCN9074
- support for rx decapsulation offload (data frames in 802.3
format)
- Qualcomm phone SoC WiFi (wcn36xx)
- enable Idle Mode Power Save (IMPS) to reduce power consumption
during idle
- Bluetooth driver support for MediaTek MT7922 and MT7921
- Enable support for AOSP Bluetooth extension in Qualcomm WCN399x and
Realtek 8822C/8852A
- Microsoft vNIC driver (mana)
- support hibernation and kexec
- Google vNIC driver (gve)
- support for jumbo frames
- implement Rx page reuse
Refactor:
- Make all writes to netdev->dev_addr go thru helpers, so that we can
add this address to the address rbtree and handle the updates
- Various TCP cleanups and optimizations including improvements to
CPU cache use
- Simplify the gnet_stats, Qdisc stats' handling and remove
qdisc->running sequence counter
- Driver changes and API updates to address devlink locking
deficiencies"
* tag 'net-next-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2122 commits)
Revert "net: avoid double accounting for pure zerocopy skbs"
selftests: net: add arp_ndisc_evict_nocarrier
net: ndisc: introduce ndisc_evict_nocarrier sysctl parameter
net: arp: introduce arp_evict_nocarrier sysctl parameter
libbpf: Deprecate AF_XDP support
kbuild: Unify options for BTF generation for vmlinux and modules
selftests/bpf: Add a testcase for 64-bit bounds propagation issue.
bpf: Fix propagation of signed bounds from 64-bit min/max into 32-bit.
bpf: Fix propagation of bounds from 64-bit min/max into 32-bit and var_off.
net: vmxnet3: remove multiple false checks in vmxnet3_ethtool.c
net: avoid double accounting for pure zerocopy skbs
tcp: rename sk_wmem_free_skb
netdevsim: fix uninit value in nsim_drv_configure_vfs()
selftests/bpf: Fix also no-alu32 strobemeta selftest
bpf: Add missing map_delete_elem method to bloom filter map
selftests/bpf: Add bloom map success test for userspace calls
bpf: Add alignment padding for "map_extra" + consolidate holes
bpf: Bloom filter map naming fixups
selftests/bpf: Add test cases for struct_ops prog
bpf: Add dummy BPF STRUCT_OPS for test purpose
...
This update has a single change which will use the maximum transfer and
message sizes advertised by SPI controllers to configure limits within
the regmap core, ensuring better interoperation.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmF/6F8ACgkQJNaLcl1U
h9Calgf+PaI6wr17nU0/m4N50Vjat0bL7iBuEQYPKFWu963M0QasPZEKteJV7sa+
8XVxcBh43E2unQkY+iMfldmBIEfZJwmsaWecdxSair6cWcm8MT6agOOkl6KjiCHM
AQiPI2+UbXDHnPociBmyA+MqI3hWSPZIMirVC+3WAFGLs8wHuRe0G97egkcPh88a
doQ5f2Ei7eCgP4uy+p93S4QWXbsbQVm/yszw0BH0gaqnBylwUfQtU1vdlLyBXW4y
9bB1MnzCdlLbKf4bQd7NcjB2bA8lgAuZ3t5rJoRjZtnf+//fRTB1cu/UkLRFlZme
vsrt60wo52r2v5tiLKA4wrgcvEFR+A==
=8MR4
-----END PGP SIGNATURE-----
Merge tag 'regmap-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap update from Mark Brown:
"A single change to use the maximum transfer and message sizes
advertised by SPI controllers to configure limits within the
regmap core, ensuring better interoperation"
* tag 'regmap-v5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: spi: Set regmap max raw r/w from max_transfer_size
This converts users of mdiobus to mdiodev using the following semantic
patch:
@@
identifier mdiodev;
expression regnum;
@@
- mdiobus_read(mdiodev->bus, mdiodev->addr, regnum)
+ mdiodev_read(mdiodev, regnum)
@@
identifier mdiodev;
expression regnum, val;
@@
- mdiobus_write(mdiodev->bus, mdiodev->addr, regnum, val)
+ mdiodev_write(mdiodev, regnum, val)
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set regmap raw read/write from spi max_transfer_size
so regmap_raw_read/write can split the access into chunks
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
[André: fix build warning]
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Link: https://lore.kernel.org/r/20211021132721.13669-1-andrealmeid@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In regcache_rbtree_insert_to_block(), when 'present' realloc failed,
the 'blk' which is supposed to assign to 'rbnode->block' will be freed,
so 'rbnode->block' points a freed memory, in the error handling path of
regcache_rbtree_init(), 'rbnode->block' will be freed again in
regcache_rbtree_exit(), KASAN will report double-free as follows:
BUG: KASAN: double-free or invalid-free in kfree+0xce/0x390
Call Trace:
slab_free_freelist_hook+0x10d/0x240
kfree+0xce/0x390
regcache_rbtree_exit+0x15d/0x1a0
regcache_rbtree_init+0x224/0x2c0
regcache_init+0x88d/0x1310
__regmap_init+0x3151/0x4a80
__devm_regmap_init+0x7d/0x100
madera_spi_probe+0x10f/0x333 [madera_spi]
spi_probe+0x183/0x210
really_probe+0x285/0xc30
To fix this, moving up the assignment of rbnode->block to immediately after
the reallocation has succeeded so that the data structure stays valid even
if the second reallocation fails.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 3f4ff561bc ("regmap: rbtree: Make cache_present bitmap per node")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211012023735.1632786-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ls-extirq irqchip driver accesses regmap inside its implementation
of the struct irq_chip :: irq_set_type method, and currently regmap
only knows to lock using normal spinlocks. But the method above wants
raw spinlock context, so this isn't going to work and triggers a
"[ BUG: Invalid wait context ]" splat.
The best we can do given the arrangement of the code is to patch regmap
and the syscon driver: regmap to support raw spinlocks, and syscon to
request them on behalf of its ls-extirq consumer.
Link: https://lore.kernel.org/lkml/20210825135438.ubcuxm5vctt6ne2q@skbuf/T/#u
Vladimir Oltean (2):
regmap: teach regmap to use raw spinlocks if requested in the config
mfd: syscon: request a regmap with raw spinlocks for some devices
drivers/base/regmap/internal.h | 4 ++++
drivers/base/regmap/regmap.c | 35 +++++++++++++++++++++++++++++-----
drivers/mfd/syscon.c | 16 ++++++++++++++++
include/linux/regmap.h | 2 ++
4 files changed, 52 insertions(+), 5 deletions(-)
--
2.25.1
base-commit: 6efb943b86
Some drivers might access regmap in a context where a raw spinlock is
held. An example is drivers/irqchip/irq-ls-extirq.c, which calls
regmap_update_bits() from struct irq_chip :: irq_set_type, which is a
method called by __irq_set_trigger() under the desc->lock raw spin lock.
Since desc->lock is a raw spin lock and the regmap internal lock for
mmio is a plain spinlock (which can become sleepable on RT), this is an
invalid locking scheme and we get a splat stating that this is a
"[ BUG: Invalid wait context ]".
It seems reasonable for regmap to have an option use a raw spinlock too,
so add that in the config such that drivers can request it.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210825205041.927788-2-vladimir.oltean@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The reg_fields array fed to {devm_}regmap_field_bulk_alloc is currently
not const, which is not correct on semantics (the functions shouldn't
change reg_field contents) and prevents pre-defined const reg_field
array to be used.
As the implementation of this function doesn't change the content of it,
just add const to its prototype.
Signed-off-by: Icenowy Zheng <icenowy@sipeed.com>
Link: https://lore.kernel.org/r/20210802063741.76301-1-icenowy@sipeed.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A const qualifier was omitted in the declaration of the regmap_bus
pointer, resulting in the following errors:
drivers/base/regmap/regmap-mdio.c: In function ‘__regmap_init_mdio’:
drivers/base/regmap/regmap-mdio.c:87:7: warning: assignment discards
‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers]
87 | bus = ®map_mdio_c22_bus;
| ^
drivers/base/regmap/regmap-mdio.c:89:7: warning: assignment discards
‘const’ qualifier from pointer target type [-Wdiscarded-qualifiers]
89 | bus = ®map_mdio_c45_bus;
| ^
Fix this by ensuring the pointer has the same qualifiers as the assigned
values.
Fixes: f083be9db0 ("regmap: mdio: Add clause-45 support")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Link: https://lore.kernel.org/r/f304ca638ffdc66d4803a6df1f75436894bd1d5f.1623244066.git.sander@svanheule.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Modern ethernet phys support the so-called clause-45 register access
mode, which allows for register address widths of 16 bit.
Also allow for 16-bit register address widths, and return a regmap for
clause-45 access in that case.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Link: https://lore.kernel.org/r/9cc263e3e7d5865edd90453b4183f1cf363cb636.1622743333.git.sander@svanheule.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently a regmap configuration for regmap-mdio must have a register
address width of 5 bits (cf. clause-22 register access). This is not
enforced on the provided register addresses, which would enable
clause-45 MDIO bus access, if the right bit packing is used.
Prevent clause-45 access, and other invalid addresses, by masking the
provided register address.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Link: https://lore.kernel.org/r/f7013f67e6d6ff56ec98660f18320f6ffcc1a777.1622743333.git.sander@svanheule.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Some interrupt controllers have inverted status register:
cleared bits is active interrupts and set bits is inactive interrupts,
so add inverted status support to the framework.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Link: https://lore.kernel.org/r/20210525034204.5272-1-fido_max@inbox.ru
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for 7 bits register, 17 bits value type register
formating. This is used, for example, by the Analog Devices
ADMV1013/ADMV1014.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Signed-off-by: Andrei Drimbarean <andrei.drimbarean@analog.com>
Message-Id: <20210526085223.14896-1-antoniu.miclaus@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap_mdio_read() breaks the principle of "no touch output till it's known
that the operation succeeds". Refactor it accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210520120518.30490-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The RTL8231 GPIO and LED expander can be configured for use as an MDIO or SMI
bus device. Currently only the MDIO mode is supported, although SMI mode
support should be fairly straightforward, once an SMI bus driver is available.
Provided features by the RTL8231:
- Up to 37 GPIOs
- Configurable drive strength: 8mA or 4mA (currently unsupported)
- Input debouncing on high GPIOs (currently unsupported)
- Up to 88 LEDs in multiple scan matrix groups
- On, off, or one of six toggling intervals
- "single-color mode": 2×36 single color LEDs + 8 bi-color LEDs
- "bi-color mode": (12 + 2×6) bi-color LEDs + 24 single color LEDs
- Up to one PWM output (currently unsupported)
- Fixed duty cycle, 8 selectable frequencies (1.2kHz - 4.8kHz)
Register access is provided through a new MDIO regmap provider. The GPIO
controller uses gpio-regmap, although a patch is required to support a
limitation of the chip.
There remain some log warnings when probing the device, possibly due to the way
I'm using the MFD subsystem. Would it be possible to avoid these?
[ 2.602242] rtl8231-pinctrl: Failed to locate of_node [id: -2]
[ 2.609380] rtl8231-pinctrl rtl8231-pinctrl.0.auto: no of_node; not parsing pinctrl DT
When no 'leds' sub-node is specified:
[ 2.922262] rtl8231-leds: Failed to locate of_node [id: -2]
[ 2.967149] rtl8231-leds rtl8231-leds.1.auto: no of_node; not parsing pinctrl DT
[ 2.975673] rtl8231-leds rtl8231-leds.1.auto: scan mode missing or invalid
[ 2.983531] rtl8231-leds: probe of rtl8231-leds.1.auto failed with error -22
Changes since v1:
- Reintroduce MDIO regmap, with fixed Kconfig dependencies
- Add configurable dir/value order for gpio-regmap direction_out call
- Drop allocations for regmap fields that are used only on init
- Move some definitions to MFD header
- Add PM ops to replace driver remove for MFD
- Change pinctrl driver to (modified) gpio-regmap
- Change leds driver to use fwnode
Link: https://lore.kernel.org/lkml/cover.1620735871.git.sander@svanheule.net/
Changes since RFC:
- Dropped MDIO regmap interface. I was unable to resolve the Kconfig
dependency issue, so have reverted to using regmap_config.reg_read/write.
- Added pinctrl support
- Added LED support
- Changed root device to MFD, with pinctrl and leds child devices. Root
device is now an mdio_device driver.
Link: https://lore.kernel.org/linux-gpio/cover.1617914861.git.sander@svanheule.net/
Sander Vanheule (7):
regmap: Add MDIO bus support
gpio: regmap: Add configurable dir/value order
dt-bindings: leds: Binding for RTL8231 scan matrix
dt-bindings: mfd: Binding for RTL8231
mfd: Add RTL8231 core device
pinctrl: Add RTL8231 pin control and GPIO support
leds: Add support for RTL8231 LED scan matrix
.../bindings/leds/realtek,rtl8231-leds.yaml | 159 ++++++++
.../bindings/mfd/realtek,rtl8231.yaml | 202 ++++++++++
drivers/base/regmap/Kconfig | 6 +-
drivers/base/regmap/Makefile | 1 +
drivers/base/regmap/regmap-mdio.c | 57 +++
drivers/gpio/gpio-regmap.c | 20 +-
drivers/leds/Kconfig | 10 +
drivers/leds/Makefile | 1 +
drivers/leds/leds-rtl8231.c | 293 ++++++++++++++
drivers/mfd/Kconfig | 9 +
drivers/mfd/Makefile | 1 +
drivers/mfd/rtl8231.c | 153 +++++++
drivers/pinctrl/Kconfig | 11 +
drivers/pinctrl/Makefile | 1 +
drivers/pinctrl/pinctrl-rtl8231.c | 377 ++++++++++++++++++
include/linux/gpio/regmap.h | 3 +
include/linux/mfd/rtl8231.h | 57 +++
include/linux/regmap.h | 36 ++
18 files changed, 1393 insertions(+), 4 deletions(-)
create mode 100644 Documentation/devicetree/bindings/leds/realtek,rtl8231-leds.yaml
create mode 100644 Documentation/devicetree/bindings/mfd/realtek,rtl8231.yaml
create mode 100644 drivers/base/regmap/regmap-mdio.c
create mode 100644 drivers/leds/leds-rtl8231.c
create mode 100644 drivers/mfd/rtl8231.c
create mode 100644 drivers/pinctrl/pinctrl-rtl8231.c
create mode 100644 include/linux/mfd/rtl8231.h
base-commit: 6efb943b86
--
2.31.1
The clean up of struct d can potentiallly index into a null array
d->virt_buf causing errorenous pointer dereferencing issues on
kfree calls. Fix this by adding a null check on d->virt_buf before
attempting to traverse the array to kfree the objects.
Addresses-Coverity: ("Dereference after null check")
Fixes: 4c50144563 ("regmap-irq: Introduce virtual regs to handle more config regs")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210406164002.430221-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable drivers to configure and modify "virtual" registers, which are
non-standard registers that further configure irq type on some devices.
Since they are non-standard, enable drivers to configure them according
to their particular idiosyncrasies by specifying an optional callback
function while registering with the framework.
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Link: https://lore.kernel.org/r/07e058cdec2297d15c95c825aa0263064d962d5a.1616613838.git.gurus@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Add "virtual" registers support to handle any irq configuration
registers in addition to the ones the framework currently supports
(status, mask, unmask, wake, type and ack). These are non-standard
registers that further configure irq type on some devices, so enable the
framework to add a variable number of them.
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Link: https://lore.kernel.org/r/a1787067004b0e11cb960319082764397469215a.1616613838.git.gurus@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Qualcomm's MFD chips have a top level interrupt status register and
sub-irqs (peripherals). When a bit in the main status register goes
high, it means that the peripheral corresponding to that bit has an
unserviced interrupt. If the bit is not set, this means that the
corresponding peripheral does not.
Commit a2d21848d9 ("regmap: regmap-irq: Add main status register
support") introduced the sub-irq logic that is currently applied only
when reading status registers, but not for any other functions like acking
or masking. Extend the use of sub-irq to all other functions, with two
caveats regarding the specification of offsets:
- Each member of the sub_reg_offsets array should be of length 1
- The specified offsets should be the unequal strides for each sub-irq
device.
In QCOM's case, all the *_base registers are to be configured to the
base addresses of the first sub-irq group, with offsets of each
subsequent group calculated as a difference from these addresses.
Continuing from the example mentioned in the cover letter:
/*
* Address of MISC_INT_MASK = 0x1011
* Address of TEMP_ALARM_INT_MASK = 0x2011
* Address of GPIO01_INT_MASK = 0x3011
*
* Calculate offsets as:
* offset_0 = 0x1011 - 0x1011 = 0 (to access MISC's
* registers)
* offset_1 = 0x2011 - 0x1011 = 0x1000
* offset_2 = 0x3011 - 0x1011 = 0x2000
*/
static unsigned int sub_unit0_offsets[] = {0};
static unsigned int sub_unit1_offsets[] = {0x1000};
static unsigned int sub_unit2_offsets[] = {0x2000};
static struct regmap_irq_sub_irq_map chip_sub_irq_offsets[] = {
REGMAP_IRQ_MAIN_REG_OFFSET(sub_unit0_offsets),
REGMAP_IRQ_MAIN_REG_OFFSET(sub_unit0_offsets),
REGMAP_IRQ_MAIN_REG_OFFSET(sub_unit0_offsets),
};
static struct regmap_irq_chip chip_irq_chip = {
--------8<--------
.not_fixed_stride = true,
.mask_base = MISC_INT_MASK,
.type_base = MISC_INT_TYPE,
.ack_base = MISC_INT_ACK,
.sub_reg_offsets = chip_sub_irq_offsets,
--------8<--------
};
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Link: https://lore.kernel.org/r/526562423eaa58b4075362083f561841f1d6956c.1615423027.git.gurus@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a upstream commit cffa4b2122f5("regmap:debugfs:
Fix a memory leak when calling regmap_attach_dev") that
adds a if condition when create name for debugfs_name.
With below function invoking logical, debugfs_name is
freed in regmap_debugfs_exit(), but it is not created again
because of the if condition introduced by above commit.
regmap_reinit_cache()
regmap_debugfs_exit()
...
regmap_debugfs_init()
So, set debugfs_name to NULL after it is freed.
Fixes: cffa4b2122 ("regmap: debugfs: Fix a memory leak when calling regmap_attach_dev")
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Link: https://lore.kernel.org/r/20210226021737.7690-1-Meng.Li@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the large set of char/misc/whatever driver subsystem updates for
5.12-rc1. Over time it seems like this tree is collecting more and more
tiny driver subsystems in one place, making it easier for those
maintainers, which is why this is getting larger.
Included in here are:
- coresight driver updates
- habannalabs driver updates
- virtual acrn driver addition (proper acks from the x86
maintainers)
- broadcom misc driver addition
- speakup driver updates
- soundwire driver updates
- fpga driver updates
- amba driver updates
- mei driver updates
- vfio driver updates
- greybus driver updates
- nvmeem driver updates
- phy driver updates
- mhi driver updates
- interconnect driver udpates
- fsl-mc bus driver updates
- random driver fix
- some small misc driver updates (rtsx, pvpanic, etc.)
All of these have been in linux-next for a while, with the only reported
issue being a merge conflict in include/linux/mod_devicetable.h that you
will hit in your tree due to the dfl_device_id addition from the fpga
subsystem in here. The resolution should be simple.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYDZf9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk3xgCcCEN+pCJTum+uAzSNH3YKs/onaDgAnRSVwOUw
tNW6n1JhXLYl9f5JdhvS
=MOHs
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc/whatever driver subsystem updates
for 5.12-rc1. Over time it seems like this tree is collecting more and
more tiny driver subsystems in one place, making it easier for those
maintainers, which is why this is getting larger.
Included in here are:
- coresight driver updates
- habannalabs driver updates
- virtual acrn driver addition (proper acks from the x86 maintainers)
- broadcom misc driver addition
- speakup driver updates
- soundwire driver updates
- fpga driver updates
- amba driver updates
- mei driver updates
- vfio driver updates
- greybus driver updates
- nvmeem driver updates
- phy driver updates
- mhi driver updates
- interconnect driver udpates
- fsl-mc bus driver updates
- random driver fix
- some small misc driver updates (rtsx, pvpanic, etc.)
All of these have been in linux-next for a while, with the only
reported issue being a merge conflict due to the dfl_device_id
addition from the fpga subsystem in here"
* tag 'char-misc-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (311 commits)
spmi: spmi-pmic-arb: Fix hw_irq overflow
Documentation: coresight: Add PID tracing description
coresight: etm-perf: Support PID tracing for kernel at EL2
coresight: etm-perf: Clarify comment on perf options
ACRN: update MAINTAINERS: mailing list is subscribers-only
regmap: sdw-mbq: use MODULE_LICENSE("GPL")
regmap: sdw: use no_pm routines for SoundWire 1.2 MBQ
regmap: sdw: use _no_pm functions in regmap_read/write
soundwire: intel: fix possible crash when no device is detected
MAINTAINERS: replace my with email with replacements
mhi: Fix double dma free
uapi: map_to_7segment: Update example in documentation
uio: uio_pci_generic: don't fail probe if pdev->irq equals to IRQ_NOTCONNECTED
drivers/misc/vmw_vmci: restrict too big queue size in qp_host_alloc_queue
firewire: replace tricky statement by two simple ones
vme: make remove callback return void
firmware: google: make coreboot driver's remove callback return void
firmware: xilinx: Use explicit values for all enum values
sample/acrn: Introduce a sample of HSM ioctl interface usage
virt: acrn: Introduce an interface for Service VM to control vCPU
...
Some late changes for sdw:
- fix for crash on intel driver
- support for _no_pm IO calls in sdw regmap
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+vs47OPLdNbVcHzyfBQHDyUjg0cFAmAmYhAACgkQfBQHDyUj
g0fs5xAAz/seDccbDQrpV99ZcLYyBqP3kH3SKykIzAy4d9UOYKsrL2dwwKmc+y/r
J6cUZ05m0OjcJPEJZayI+tvn1sl3qIuNAAk+0KLZ++jy03LajENloArk13T/xhGq
GiRlgcCiB1pp1qRk7abAvQWfApeq77Mq3dwKG5lZbOrFZTc+lu78poMnpFfMHF9O
cn9h5TrQ1tbqU4gj93DAjI4OOQSq7bxHbz1P38GlYP32ZYZW3WF4Fu0fNk6ZQp52
eraUVO3+2PqbtB8t6PhENCIIJDnO1rgo8Bf//4Fpx3Sa2fECk0TPjOdHH4G7DITI
GV8Ar9uG8tb/EyNfS4/R0lHDAaVGnicry2BDFUy3bv7fqnIp/Py8to3L0w3Kx+RF
flm3QMEFPUkoDj65n0Vf1E7y6hxT8Kh1VX81ssFKzkc7vBgtWjba+dQDn+Ym46H5
Njsp/KovokK5MwMkfh5mrN+kmayEhwwltzdMb5OTw2y9NgChDNxXML8JsHTXtoLL
05lKOgXzVQLcALagjZKmkiVt9KtCgDJW2Kmsp/FBO9hOA/dCA5aMcWiYhRarkl8q
z80DunYtA+RUBm+2P4tpntCCxlWZIvjbtpggmmJ6r5m3eB5m5Ud/lOEauyvADUT6
eT+JsgEZr31Yt4s9K1UBB6OiQatIxKwvB2PZDiBSKWUJpl00H0g=
=eJnY
-----END PGP SIGNATURE-----
Merge tag 'soundwire-2_5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-next
Vinod writes:
soundwire second update for 5.12-rc1
Some late changes for sdw:
- fix for crash on intel driver
- support for _no_pm IO calls in sdw regmap
* tag 'soundwire-2_5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
regmap: sdw-mbq: use MODULE_LICENSE("GPL")
regmap: sdw: use no_pm routines for SoundWire 1.2 MBQ
regmap: sdw: use _no_pm functions in regmap_read/write
soundwire: intel: fix possible crash when no device is detected
"GPL v2" is the same as "GPL". It exists for historic reasons.
See Documentation/process/license-rules.rst
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210122070634.12825-8-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use no_pm versions for write and read.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210122070634.12825-7-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
sdw_update_slave_status will be invoked when a codec is attached,
and the codec driver will initialize the codec with regmap functions
while the codec device is pm_runtime suspended.
regmap routines currently rely on regular SoundWire IO functions,
which will call pm_runtime_get_sync()/put_autosuspend.
This causes a deadlock where the resume routine waits for an
initialization complete signal that while the initialization complete
can only be reached when the resume completes.
The only solution if we allow regmap functions to be used in resume
operations as well as during codec initialization is to use _no_pm
routines. The duty of making sure the bus is operational needs to be
handled above the regmap level.
Fixes: 7c22ce6e21 ('regmap: Add SoundWire bus support')
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210122070634.12825-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix the following coccicheck warnings:
./drivers/base/regmap/regcache.c:71:3-18: WARNING: Assignment of
0/1 to bool variable.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Zhong <abaci-bugfix@linux.alibaba.com>
Link: https://lore.kernel.org/r/1611215961-33725-1-git-send-email-abaci-bugfix@linux.alibaba.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This code will leak "map->debugfs_name" because the if statement is
reversed so it only frees NULL pointers instead of non-NULL. In
fact the if statement is not required and should just be removed
because kfree() accepts NULL pointers.
Fixes: cffa4b2122 ("regmap: debugfs: Fix a memory leak when calling regmap_attach_dev")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X/RQpfAwRdLg0GqQ@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
After initializing the regmap through
syscon_regmap_lookup_by_compatible, then regmap_attach_dev to the
device, because the debugfs_name has been allocated, there is no
need to redistribute it again
unreferenced object 0xd8399b80 (size 64):
comm "swapper/0", pid 1, jiffies 4294937641 (age 278.590s)
hex dump (first 32 bytes):
64 75 6d 6d 79 2d 69 6f 6d 75 78 63 2d 67 70 72
dummy-iomuxc-gpr
40 32 30 65 34 30 30 30 00 7f 52 5b d8 7e 42 69
@20e4000..R[.~Bi
backtrace:
[<ca384d6f>] kasprintf+0x2c/0x54
[<6ad3bbc2>] regmap_debugfs_init+0xdc/0x2fc
[<bc4181da>] __regmap_init+0xc38/0xd88
[<1f7e0609>] of_syscon_register+0x168/0x294
[<735e8766>] device_node_get_regmap+0x6c/0x98
[<d96c8982>] imx6ul_init_machine+0x20/0x88
[<0456565b>] customize_machine+0x1c/0x30
[<d07393d8>] do_one_initcall+0x80/0x3ac
[<7e584867>] kernel_init_freeable+0x170/0x1f0
[<80074741>] kernel_init+0x8/0x120
[<285d6f28>] ret_from_fork+0x14/0x20
[<00000000>] 0x0
Fixes: 9b947a13e7 ("regmap: use debugfs even when no device")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Link: https://lore.kernel.org/r/20201229105046.41984-1-xiaolei.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This is quite a busy release for regmap with two substantial features
being added:
- Support for register maps Soundwire 1.2 multi-byte operations,
allowing atomic support for registers larger than a single byte.
- Support for relaxed I/O without barriers in MMIO regmaps, allowing
them to be used efficiently on systems where default MMIO operations
include barriers.
There was also an addition and revert of use of the new Soundwire
support for RT715 due to build issues with the driver built in, my tests
only covered building it as a module, the patch wasn't just dropped as
it had already been merged elsewhere.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl/XdOYACgkQJNaLcl1U
h9DKWwf7BVgrH1vcgOdZ/8xbVnu2pmNGJzHydfV2XD2fHuEgkuVN1dv756HFCzBj
XpHGa+XRGt1j39KsBqhcBOGuCLiTmjmoxWXq4MnBFVHcXBNRk1z6YFtkeZBkRi0j
ZxZNlrrCCaFp8KmqyqMeIU9DbiQ/ITTH/1VBcffnprYI1J9gK4JQE0iisaMIap90
XwKx4VUwT63yVZQGJPW4t65uMUbPTRqcZQzfj3DGhjmkhNI/EvpPU44K11I+op/6
7J9enekMlbOR5t7606h9gAapW1Qt+YrvTwciT9mzGNsmO8MmyUIRQUYuZAzp5RIT
BH5aIRfTUb6lYuktSKI8STrbOUdi/A==
=194Y
-----END PGP SIGNATURE-----
Merge tag 'regmap-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This is quite a busy release for regmap with two substantial features
being added:
- Support for register maps Soundwire 1.2 multi-byte operations,
allowing atomic support for registers larger than a single byte.
- Support for relaxed I/O without barriers in MMIO regmaps, allowing
them to be used efficiently on systems where default MMIO
operations include barriers.
There was also an addition and revert of use of the new Soundwire
support for RT715 due to build issues with the driver built in, my
tests only covered building it as a module, the patch wasn't just
dropped as it had already been merged elsewhere"
* tag 'regmap-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
ASoC: rt715: Fix build
regmap: sdw: add required header files
regmap: Remove duplicate `type` field from regmap `regcache_sync` trace event
regmap: Fix order of regmap write log
regmap: mmio: add config option to allow relaxed MMIO accesses
Core:
- Consolidation and robustness changes for irq time accounting
- Cleanup and consolidation of irq stats
- Remove the fasteoi IPI flow which has been proved useless
- Provide an interface for converting legacy interrupt mechanism into
irqdomains
Drivers:
The rare event of not having completely new chip driver code, just new
DT bindings and extensions of existing drivers to accomodate new
variants!
- Preliminary support for managed interrupts on platform devices
- Correctly identify allocation of MSIs proxyied by another device
- Generalise the Ocelot support to new SoCs
- Improve GICv4.1 vcpu entry, matching the corresponding KVM optimisation
- Work around spurious interrupts on Qualcomm PDC
- Random fixes and cleanups
Thanks,
tglx
-----BEGIN PGP SIGNATURE-----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=iytv
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-12-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Generic interrupt and irqchips subsystem updates. Unusually, there is
not a single completely new irq chip driver, just new DT bindings and
extensions of existing drivers to accomodate new variants!
Core:
- Consolidation and robustness changes for irq time accounting
- Cleanup and consolidation of irq stats
- Remove the fasteoi IPI flow which has been proved useless
- Provide an interface for converting legacy interrupt mechanism into
irqdomains
Drivers:
- Preliminary support for managed interrupts on platform devices
- Correctly identify allocation of MSIs proxyied by another device
- Generalise the Ocelot support to new SoCs
- Improve GICv4.1 vcpu entry, matching the corresponding KVM
optimisation
- Work around spurious interrupts on Qualcomm PDC
- Random fixes and cleanups"
* tag 'irq-core-2020-12-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
irqchip/qcom-pdc: Fix phantom irq when changing between rising/falling
driver core: platform: Add devm_platform_get_irqs_affinity()
ACPI: Drop acpi_dev_irqresource_disabled()
resource: Add irqresource_disabled()
genirq/affinity: Add irq_update_affinity_desc()
irqchip/gic-v3-its: Flag device allocation as proxied if behind a PCI bridge
irqchip/gic-v3-its: Tag ITS device as shared if allocating for a proxy device
platform-msi: Track shared domain allocation
irqchip/ti-sci-intr: Fix freeing of irqs
irqchip/ti-sci-inta: Fix printing of inta id on probe success
drivers/irqchip: Remove EZChip NPS interrupt controller
Revert "genirq: Add fasteoi IPI flow"
irqchip/hip04: Make IPIs use handle_percpu_devid_irq()
irqchip/bcm2836: Make IPIs use handle_percpu_devid_irq()
irqchip/armada-370-xp: Make IPIs use handle_percpu_devid_irq()
irqchip/gic, gic-v3: Make SGIs use handle_percpu_devid_irq()
irqchip/ocelot: Add support for Jaguar2 platforms
irqchip/ocelot: Add support for Serval platforms
irqchip/ocelot: Add support for Luton platforms
irqchip/ocelot: prepare to support more SoC
...
The MIPI SoundWire Device Class standard will define audio functionality
beyond the scope of the existing SoundWire 1.2 standard, which is limited
to the bus and interface.
The description is inspired by the USB Audio Class, with "functions",
"entities", "control selectors", "audio clusters". The main difference
with the USB Audio class is that the devices are typically on a motherboard
and descriptors stored in platform firmware instead of being retrieved
from the device.
The current set of devices managed in this patchset are conformant with the
SDCA 0.6 specification and require dedicated drivers since the descriptors
and platform firmware specification is not complete at this time. They do
however rely on the hierarchical addressing required by the SDCA standard.
Future devices conformant with SDCA 1.0 should rely on a class driver.
This series adds support for the hierarchical SDCA addressing and extends
regmap. It then provides 3 codecs for RT711-sdca headset codec, RT1316
amplifier and RT715-scda microphone codec.
Note that the release of this code before the formal adoption of the
SDCA 1.0 specification was formally endorsed by the MIPI Board to make
sure there is no delay for Linux-based support of this specification.
Jack Yu (1):
ASoC/SoundWire: rt715-sdca: First version of rt715 sdw sdca codec
driver
Pierre-Louis Bossart (2):
soundwire: SDCA: add helper macro to access controls
regmap/SoundWire: sdw: add support for SoundWire 1.2 MBQ
Shuming Fan (2):
ASoC/SoundWire: rt1316: Add RT1316 SDCA vendor-specific driver
ASoC/SoundWire: rt711-sdca: Add RT711 SDCA vendor-specific driver
drivers/base/regmap/Kconfig | 6 +-
drivers/base/regmap/Makefile | 1 +
drivers/base/regmap/regmap-sdw-mbq.c | 101 ++
include/linux/regmap.h | 35 +
include/linux/soundwire/sdw_registers.h | 32 +
sound/soc/codecs/Kconfig | 20 +
sound/soc/codecs/Makefile | 6 +
sound/soc/codecs/rt1316-sdw.c | 756 ++++++++++++
sound/soc/codecs/rt1316-sdw.h | 115 ++
sound/soc/codecs/rt711-sdca-sdw.c | 424 +++++++
sound/soc/codecs/rt711-sdca-sdw.h | 101 ++
sound/soc/codecs/rt711-sdca.c | 1481 +++++++++++++++++++++++
sound/soc/codecs/rt711-sdca.h | 246 ++++
sound/soc/codecs/rt715-sdca-sdw.c | 278 +++++
sound/soc/codecs/rt715-sdca-sdw.h | 170 +++
sound/soc/codecs/rt715-sdca.c | 936 ++++++++++++++
sound/soc/codecs/rt715-sdca.h | 124 ++
17 files changed, 4831 insertions(+), 1 deletion(-)
create mode 100644 drivers/base/regmap/regmap-sdw-mbq.c
create mode 100644 sound/soc/codecs/rt1316-sdw.c
create mode 100644 sound/soc/codecs/rt1316-sdw.h
create mode 100644 sound/soc/codecs/rt711-sdca-sdw.c
create mode 100644 sound/soc/codecs/rt711-sdca-sdw.h
create mode 100644 sound/soc/codecs/rt711-sdca.c
create mode 100644 sound/soc/codecs/rt711-sdca.h
create mode 100644 sound/soc/codecs/rt715-sdca-sdw.c
create mode 100644 sound/soc/codecs/rt715-sdca-sdw.h
create mode 100644 sound/soc/codecs/rt715-sdca.c
create mode 100644 sound/soc/codecs/rt715-sdca.h
base-commit: 3650b228f8
--
2.17.1
The SoundWire 1.1 specification only allowed for reads and writes of
bytes. The SoundWire 1.2 specification adds a new capability to
transfer "Multi-Byte Quantities" (MBQ) across the bus. The transfers
still happens one-byte-at-a-time, but the update is atomic.
For example when writing a 16-bit volume, the first byte transferred
is only taken into account when the second byte is successfully
transferred.
The mechanism is symmetrical for read and writes:
- On a read, the address of the last byte to be read is modified by
setting the MBQ bit
- On a write, the address of all but the last byte to be written are
modified by setting the MBQ bit. The address for the last byte relies
on the MBQ bit being cleared.
The current definitions for MBQ-based controls in the SDCA draft
standard are limited to 16 bits for volumes, so for now this is the
only supported format. An update will be provided if and when support
for 24-bit and 32-bit values is specified by the SDCA standard.
One possible objection is that this code could have been handled with
regmap-sdw.c. However this is a new spec addition not handled by every
SoundWire 1.1 and non-SDCA device, so there's no reason to load code
that will never be used.
Also in practice it's extremely unlikely that CONFIG_REGMAP would not
be selected with CONFIG_REGMAP_MBQ selected. However there's no
functional dependency between the two modules so they can be selected
separately.
Reviewed-by: Rander Wang <rander.wang@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201103172226.4278-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
I have an error saying that `regcache_sync` has 2 fields named `type`
while using libtraceevent.
Erase the `int field` type, which is not assigned. This field is
introduced by mistake and this commit removes it.
Fixes: 5936008901 ("regmap: Add the regcache_sync trace event")
Signed-off-by: Philippe Duplessis-Guindon <pduplessis@efficios.com>
Link: https://lore.kernel.org/r/20201124135730.9185-1-pduplessis@efficios.com
Signed-off-by: Mark Brown <broonie@kernel.org>
_regmap_write can trigger a _regmap_select_page, which will call
another _regmap_write that will be executed first, but the log shows
the inverse order
Also, keep consistency with _regmap_read which only logs in case of
success
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20201112150217.459844-1-tanureal@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
irq_domain_create_legacy() takes a fwnode as parameter contrary to
irq_domain_add_legacy() which requires a OF node.
Switch the regmap irq domain creation to use that new function so it is not
longer limited to OF based usage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20201030165919.86234-6-andriy.shevchenko@linux.intel.com
On some platforms (eg armv7 due to the CONFIG_ARM_DMA_MEM_BUFFERABLE)
MMIO R/W operations always add memory barriers which can increase load,
decrease battery life or in general reduce performance unnecessarily
on devices which access a lot of configuration registers and where
ordering does not matter (eg. media accelerators like the Verisilicon /
Hantro video decoders).
Drivers used to call the relaxed MMIO variants directly but since they
are now accessing the MMIO registers via regmaps (to compensate for
different VPU HW reg layouts via regmap fields), there is a need for a
relaxed API / config to preserve existing behaviour.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Link: https://lore.kernel.org/r/20201014203024.954369-1-adrian.ratiu@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For particular codec HWs have requirement to toggle interrupt clear
register twice 0->1->0. To accommodate it, need to add one more field
(clear_ack) in the regmap_irq struct and update regmap-irq driver to
support it.
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
Link: https://lore.kernel.org/r/1601907440-13373-1-git-send-email-lkasam@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Useful for devices with many fields.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9yPoATHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0JsoB/9zhtYrqKbof0AKuMfEeO+pPo4dC/9l
O7ENgSXCb9PWy0auVpU62ISXBPadbbrQXXe3hJ1Zof5q17lYqbaLM7Uem3bxIYtc
0HHRIb49R1sP+99T2JB3RDu/ykzHJsfxCkLgMR5MvBgS5e3KKf0SqZgNSVTYT4Y5
oPt81sxW56Z8FLrLn0j1sVDXlro4/uBpDOcHyzgq4GWgQ6ACvnIOH+PQUTTcGBfT
LtIkRMO8mHNKsDCy9Qy12NRsaparIbYb7KKEY9IR+6TN+qJ/g5PJQcPmsU6b0NIl
pb7fv4IRTvPDaEPa1g20U88qkSE5H3PXp88R3y/JbSMuFJwWwS2AGwYd
=L+6w
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl9yPpwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0PkDB/9ybt51NqJWyU3JaleY7otD2QvCmvl6
2dzpDncfjYZ8GOhvju74BQM9h/m9EHzb5FQ1yLMKEeICXZwxkDgHiqMLYLN1e6wx
ug5U6lvbT1TmeBa7IJYNNSGH2BKeIDM5Hm2zVvMpEJhF2Y9uAE0HqxjGL3CfbUOv
R2o2K3wgax83FfX86wmYNgkkp4Ri1qviD1Jr90zzFZRr0FAjiyrFHXdfdvK/wUx1
5n9wg+aIehQr1a8cKYQaqWd3HZR6pofmOj1cO4n/By+VEYRWaVds8OKUrqimZ2mE
moX9+ooY3eFdmS6kgtA31bgBFjKxfMNaTzTa4B3kikmxSOKMupQejBn9
=G3GG
-----END PGP SIGNATURE-----
Merge tag 'regmap-field-bulk-api' into regmap-5.10
regmap: Add a bulk field API
Useful for devices with many fields.
Usage of regmap_field_alloc becomes much overhead when number of fields
exceed more than 3.
QCOM LPASS driver has extensively converted to use regmap_fields.
Using new bulk api to allocate fields makes it much more cleaner code to read!
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Link: https://lore.kernel.org/r/20200925164856.10315-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
While not destroying mutexes doesn't lead to memory leaks, it's still
the correct thing to do for mutex debugging accounting.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200928120614.23172-1-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Many error paths in __regmap_init rely on ret being pre-initialised to
-EINVAL, add an extra initialisation in after the new call to
regmap_set_name.
Fixes: 94cc89eb8f ("regmap: debugfs: Fix handling of name string for debugfs init delays")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200918152212.22200-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Non-incrementing writes can fail if register + length crosses page
border. However for non-incrementing writes we should not check for page
border crossing. Fix this by passing additional flag to _regmap_raw_write
and passing length to _regmap_select_page basing on the flag.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: cdf6b11daa ("regmap: Add regmap_noinc_write API")
Link: https://lore.kernel.org/r/20200917153405.3139200-2-dmitry.baryshkov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Non-incrementing reads can fail if register + length crosses page
border. However for non-incrementing reads we should not check for page
border crossing. Fix this by passing additional flag to _regmap_raw_read
and passing length to _regmap_select_page basing on the flag.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 74fe7b551f ("regmap: Add regmap_noinc_read API")
Link: https://lore.kernel.org/r/20200917153405.3139200-1-dmitry.baryshkov@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: 94cc89eb8f ("regmap: debugfs: Fix handling of name string for debugfs init delays")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200918112002.15216-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In regmap_debugfs_init the initialisation of the debugfs is delayed
if the root node isn't ready yet. Most callers of regmap_debugfs_init
pass the name from the regmap_config, which is considered temporary
ie. may be unallocated after the regmap_init call returns. This leads
to a potential use after free, where config->name has been freed by
the time it is used in regmap_debugfs_initcall.
This situation can be seen on Zynq, where the architecture init_irq
callback registers a syscon device, using a local variable for the
regmap_config. As init_irq is very early in the platform bring up the
regmap debugfs root isn't ready yet. Although this doesn't crash it
does result in the debugfs entry not having the correct name.
Regmap already sets map->name from config->name on the regmap_init
path and the fact that a separate field is used to pass the name
to regmap_debugfs_init appears to be an artifact of the debugfs
name being added before the map name. As such this patch updates
regmap_debugfs_init to use map->name, which is already duplicated from
the config avoiding the issue.
This does however leave two lose ends, both regmap_attach_dev and
regmap_reinit_cache can be called after a regmap is registered and
would have had the effect of applying a new name to the debugfs
entries. In both of these cases it was chosen to update the map
name. In the case of regmap_attach_dev there are 3 users that
currently use this function to update the name, thus doing so avoids
changes for those users and it seems reasonable that attaching
a device would want to set the name of the map. In the case of
regmap_reinit_cache the primary use-case appears to be devices that
need some register access to identify the device (for example devices
in the same family) and then update the cache to match the exact
hardware. Whilst no users do currently update the name here, given the
use-case it seemed reasonable the name might want to be updated once
the device is better identified.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200917120828.12987-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Devices such as the AD5628 require 32 bits of data divided in 12 bits
for dummy, command and address, and 20 for data and dummy. Eg:
XXXXCCCCAAAADDDDDDDDDDDDDDDDXXXX
Where X is dont care, C is command, A is address and D is data bits.
Which would requierd the following regmap_config:
static const struct regmap_config config_dac = {
.reg_bits = 12,
.val_bits = 20,
.max_register = 0xff,
};
Signed-off-by: Ricardo Ribalda <ribalda@kernel.org>
Link: https://lore.kernel.org/r/20200917114727.1120373-1-ribalda@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Regmap can't sleep if spinlock is used for the locking protection.
This patch fixes regression caused by a previous commit that switched
regmap to use fsleep() and this broke Amlogic S922X platform.
This patch adds new configuration option for regmap users, allowing to
specify whether regmap operations can sleep and assuming that sleep is
allowed if mutex is used for the regmap locking protection.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 2b32d2f7ce ("regmap: Use flexible sleep")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200902141843.6591-1-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hello!
This series adds support for the Embedded Controller which is found on
Acer Iconia Tab A500 (Android tablet device).
The Embedded Controller is ENE KB930 and it's running firmware customized
for the A500. The firmware interface may be reused by some other sibling
Acer tablets, although none of those tablets are supported in upstream yet.
Please review and apply, thanks in advance!
Changelog:
v2: - Factored out KB930 device-tree binding into a separate file, like it
was suggested by Lubomir Rintel.
- Switched to use regmap API like it was suggested by Lubomir Rintel.
- Added patch "regmap: Use flexible sleep" which allows not to hog
CPU while LED is switching state.
- Corrected MODULE_LICENSE to use "GPL" in all patches.
- Corrected MFD driver Kconfig entry like it was suggested by
Lubomir Rintel, it now depends on I2C.
- Switched to use I2C probe_new() in the MFD driver.
- Renamed the global pm_off variable, like it was suggested by
Lubomir Rintel and Lee Jones.
- Dropped serial number from the battery driver because I realized
that it's not a battery serial, but a device serial.
- Battery driver now uses dev_err_probe(), like it was suggested by
Sebastian Reichel.
- Dropped legacy LED_ON usage from the LED driver and renamed the
LEDs, like it was suggested by Pavel Machek. I also checked whether
LED-name customization via device-tree could be needed by other
potentially compatible devices and it shouldn't be needed, anyways it
won't be difficult to extend the code even if I'm wrong.
Dmitry Osipenko (6):
dt-bindings: mfd: Add ENE KB930 Embedded Controller binding
regmap: Use flexible sleep
mfd: Add driver for Embedded Controller found on Acer Iconia Tab A500
power: supply: Add battery gauge driver for Acer Iconia Tab A500
leds: Add driver for Acer Iconia Tab A500
ARM: tegra: acer-a500: Add Embedded Controller
.../devicetree/bindings/mfd/ene-kb930.yaml | 66 ++++
.../boot/dts/tegra20-acer-a500-picasso.dts | 17 +
drivers/base/regmap/regmap.c | 4 +-
drivers/leds/Kconfig | 7 +
drivers/leds/Makefile | 1 +
drivers/leds/leds-acer-a500.c | 130 ++++++++
drivers/mfd/Kconfig | 12 +
drivers/mfd/Makefile | 1 +
drivers/mfd/acer-ec-a500.c | 203 ++++++++++++
drivers/power/supply/Kconfig | 6 +
drivers/power/supply/Makefile | 1 +
drivers/power/supply/acer_a500_battery.c | 297 ++++++++++++++++++
12 files changed, 743 insertions(+), 2 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mfd/ene-kb930.yaml
create mode 100644 drivers/leds/leds-acer-a500.c
create mode 100644 drivers/mfd/acer-ec-a500.c
create mode 100644 drivers/power/supply/acer_a500_battery.c
--
2.27.0
base-commit: f75aef392f
The multi-reg write function uses udelay(), which is a busy-loop based
delaying function that is not suitable for a long delays. Hence let's
replace the udelay() with fsleep(), which is flexible sleep function that
selects best delay function based on the delay-time.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200830185356.5365-3-digetx@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch add support for regmap APIs that are intended to be used by
the drivers of some SPI slave chips which integrate the "SPI slave to
Avalon Master Bridge" (spi-avmm) IP.
The spi-avmm IP acts as a bridge to convert encoded streams of bytes
from the host to the chip's internal register read/write on Avalon bus.
The driver implements the register read/write operations for a generic
SPI master to access the sub devices behind spi-avmm bridge.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Reviewed-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com>
Link: https://lore.kernel.org/r/1597822497-25107-2-git-send-email-yilun.xu@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If a regmap has "fast_io" set then its lock function uses a spinlock.
That doesn't work so well with the functions:
* regmap_cache_only_write_file()
* regmap_cache_bypass_write_file()
Both of the above functions have the pattern:
1. Lock the regmap.
2. Call:
debugfs_write_file_bool()
copy_from_user()
__might_fault()
__might_sleep()
Let's reorder things a bit so that we do all of our sleepable
functions before we grab the lock.
Fixes: d3dc5430d6 ("regmap: debugfs: Allow writes to cache state settings")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200715164611.1.I35b3533e8a80efde0cec1cc70f71e1e74b2fa0da@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
CONFIG_REGMAP is not selected when no other serial bus is supported.
It's largely academic since CONFIG_I2C is usually selected e.g. by
DRM, but still this can break randconfig so let's be explicit.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200707202628.113142-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert the argument to the newer fwnode_handle instead a device tree
node. Fortunately, there are no users for now. So this is an easy
change.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200706175353.16404-2-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
This function is used by dev_get_regmap() to retrieve a regmap for the
specified device. If the device has more than one regmap, the name parameter
can be used to specify one.
The code here uses a pointer comparison to check for equal strings. This
however will probably always fail, as the regmap->name is allocated via
kstrdup_const() from the regmap's config->name.
Fix this by using strcmp() instead.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20200703103315.267996-1-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
A few small fixes, none of which are likely to have any substantial
impact here - the most substantial one is a fix for a long standing
memory leak on devices that use register patching which will only have
an impact if the device is removed and re-added.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl7wllsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0L5pB/sEQIAR3U1OY7Wh/fln5BvAVkjazr60
PGclUzIWSOuNdMQBClibQhIJkTwLA3BjW1o0db3qB7ulZArGT5KqNdY0z0BkUkPz
6/l297XHerHkNmQc16F9NqT6RX8Xori/mke0DuHkurxq+A1iS970Q3a9todz0ZWB
UuMVfE6a3i13QxhahQmp86NNUH3BbWgyDRUuJELdHGyM7Ydit7Tt1kYLua1TTdBQ
t7R00ukv0XSLG4vCIfSjFajVlzQZIM1YEzefY9TUAWaOc/2znj0syUGn1FehdV5J
a01BWk91jNecHq6K8sIKV7N4z4OUKQqkwlyj+KkB0iMf11xezkJnWCZC
=yvq/
-----END PGP SIGNATURE-----
Merge tag 'regmap-fix-v5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"A few small fixes, none of which are likely to have any substantial
impact here - the most substantial one is a fix for a long standing
memory leak on devices that use register patching which will only have
an impact if the device is removed and re-added"
* tag 'regmap-fix-v5.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Fix memory leak from regmap_register_patch
regmap: fix the kerneldoc for regmap_test_bits()
regmap: fix alignment issue
When a register patch is registered the reg_sequence is copied but the
memory allocated is never freed. Add a kfree in regmap_exit to clean it
up.
Fixes: 22f0d90a34 ("regmap: Support register patch sets")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200617152129.19655-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are two spaces between arguments in regmap_fields_update_bits_base()
so remove one.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200615072507.11303-1-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
The kerneldoc comment for regmap_test_bits() says that it returns -1 on
regmap_read() failure. This is not true - it will propagate the error
code returned by regmap_read(). Fix it.
Fixes: aa2ff9dbae ("regmap: provide helpers for simple bit operations")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200607093421.22209-1-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
The assembly and disassembly of data to be sent to or received from
a device invoke functions regmap_format_XX() and regmap_parse_XX()
that extract or insert data items from or into a buffer, using
assignments. In some cases the functions are called with a buffer
pointer with an odd address. On architectures with strict alignment
requirements this can result in a kernel crash. The assignments
have been replaced by functions that take alignment into account.
Signed-off-by: Jens Thoms Toerring <jt@toerring.de>
Link: https://lore.kernel.org/r/20200531095300.GA27570@toerring.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Bartosz Golaszewski <bgolaszewski@baylibre.com>:
From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
I noticed that oftentimes I use regmap_update_bits() for simple bit
setting or clearing. In this case the fourth argument is superfluous as
it's always 0 or equal to the mask argument.
This series proposes to add simple bit operations for setting, clearing
and testing specific bits with regmap.
The second patch uses all three in a driver that got recently picked into
the net-next tree.
The patches obviously target different trees so - if you're ok with
the change itself - I propose you pick the first one into your regmap
tree for v5.8 and then I'll resend the second patch to add the first
user for these macros for v5.9.
v1 -> v2:
- convert the new macros to static inline functions
v2 -> v3:
- drop unneeded ternary operator
Bartosz Golaszewski (2):
regmap: provide helpers for simple bit operations
net: ethernet: mtk-star-emac: use regmap bitops
drivers/base/regmap/regmap.c | 22 +++++
drivers/net/ethernet/mediatek/mtk_star_emac.c | 80 ++++++++-----------
include/linux/regmap.h | 36 +++++++++
3 files changed, 93 insertions(+), 45 deletions(-)
base-commit: 8f3d9f3542
--
2.26.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
In many instances regmap_update_bits() is used for simple bit setting
and clearing. In these cases the last argument is redundant and we can
hide it with a static inline function.
This adds three new helpers for simple bit operations: set_bits,
clear_bits and test_bits (the last one defined as a regular function).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200528154503.26304-2-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows to access data with 16-bit width of registers
via i2c SMBus block functions.
The multi-command sequence of the reading function is not safe
and may read the wrong data from other address if other commands
are sent in-between the SMBus commands in the read function.
Read performance:
32768 bytes (33 kB, 32 KiB) copied, 11.4869 s, 2.9 kB/s
Write performance(with 1-byte page):
32768 bytes (33 kB, 32 KiB) copied, 129.591 s, 0.3 kB/s
The implementation is inspired by below commit
https://patchwork.ozlabs.org/patch/545292/
v2: add more descriptions about the issue that maybe introduced
by this commit
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Link: https://lore.kernel.org/r/20200424123358.144850-1-acelan.kao@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Kontron sl28cpld is a board management chip providing gpio, pwm, fan
monitoring and an interrupt controller. For now this controller is used on
the Kontron SMARC-sAL28 board. But because of its flexible nature, it
might also be used on other boards in the future. The individual blocks
(like gpio, pwm, etc) are kept intentionally small. The MFD core driver
then instantiates different (or multiple of the same) blocks. It also
provides the register layout so it might be updated in the future without a
device tree change; and support other boards with a different layout or
functionalities.
See also [1] for more information.
This is my first take of a MFD driver. I don't know whether the subsystem
maintainers should only be CCed on the patches which affect the subsystem
or on all patches for this series. I've chosen the latter so you can get a
more complete picture.
[1] https://lore.kernel.org/linux-devicetree/0e3e8204ab992d75aa07fc36af7e4ab2@walle.cc/
Changes since v1:
- use of_match_table in all drivers, needed for automatic module loading,
when using OF_MFD_CELL()
- add new gpio-regmap.c which adds a generic regmap gpio_chip implemention
- new patch for reqmap_irq, so we can reuse its implementation
- remove almost any code from gpio-sl28cpld.c, instead use gpio-regmap and
regmap-irq
- change the handling of the mfd core vs device tree nodes; add a new
property "of_reg" to the mfd_cell struct which, when set, is matched to
the unit-address of the device tree nodes.
- fix sl28cpld watchdog when it is not initialized by the bootloader.
Explicitly set the operation mode.
- also add support for kontron,assert-wdt-timeout-pin in sl28cpld-wdt.
As suggested by Bartosz Golaszewski:
- define registers as hex
- make gpio enum uppercase
- move parent regmap check before memory allocation
- use device_property_read_bool() instead of the of_ version
- mention the gpio flavors in the bindings documentation
As suggested by Guenter Roeck:
- cleanup #includes and sort them
- use devm_watchdog_register_device()
- use watchdog_stop_on_reboot()
- provide a Documentation/hwmon/sl28cpld.rst
- cleaned up the weird tristate->bool and I2C=y issue. Instead mention
that the MFD driver is bool because of the following intc patch
- removed the SL28CPLD_IRQ typo
As suggested by Rob Herring:
- combine all dt bindings docs into one patch
- change the node name for all gpio flavors to "gpio"
- removed the interrupts-extended rule
- cleaned up the unit-address space, see above
Michael Walle (16):
include/linux/ioport.h: add helper to define REG resource constructs
mfd: mfd-core: Don't overwrite the dma_mask of the child device
mfd: mfd-core: match device tree node against reg property
regmap-irq: make it possible to add irq_chip do a specific device node
dt-bindings: mfd: Add bindings for sl28cpld
mfd: Add support for Kontron sl28cpld management controller
irqchip: add sl28cpld interrupt controller support
watchdog: add support for sl28cpld watchdog
pwm: add support for sl28cpld PWM controller
gpio: add a reusable generic gpio_chip using regmap
gpio: add support for the sl28cpld GPIO controller
hwmon: add support for the sl28cpld hardware monitoring controller
arm64: dts: freescale: sl28: enable sl28cpld
arm64: dts: freescale: sl28: map GPIOs to input events
arm64: dts: freescale: sl28: enable LED support
arm64: dts: freescale: sl28: enable fan support
.../bindings/gpio/kontron,sl28cpld-gpio.yaml | 51 +++
.../hwmon/kontron,sl28cpld-hwmon.yaml | 27 ++
.../bindings/mfd/kontron,sl28cpld.yaml | 162 +++++++++
.../bindings/pwm/kontron,sl28cpld-pwm.yaml | 35 ++
.../watchdog/kontron,sl28cpld-wdt.yaml | 35 ++
Documentation/hwmon/sl28cpld.rst | 36 ++
.../fsl-ls1028a-kontron-kbox-a-230-ls.dts | 14 +
.../fsl-ls1028a-kontron-sl28-var3-ads2.dts | 9 +
.../freescale/fsl-ls1028a-kontron-sl28.dts | 124 +++++++
drivers/base/regmap/regmap-irq.c | 84 ++++-
drivers/gpio/Kconfig | 15 +
drivers/gpio/Makefile | 2 +
drivers/gpio/gpio-regmap.c | 321 ++++++++++++++++++
drivers/gpio/gpio-sl28cpld.c | 187 ++++++++++
drivers/hwmon/Kconfig | 10 +
drivers/hwmon/Makefile | 1 +
drivers/hwmon/sl28cpld-hwmon.c | 152 +++++++++
drivers/irqchip/Kconfig | 3 +
drivers/irqchip/Makefile | 1 +
drivers/irqchip/irq-sl28cpld.c | 99 ++++++
drivers/mfd/Kconfig | 21 ++
drivers/mfd/Makefile | 2 +
drivers/mfd/mfd-core.c | 31 +-
drivers/mfd/sl28cpld.c | 154 +++++++++
drivers/pwm/Kconfig | 10 +
drivers/pwm/Makefile | 1 +
drivers/pwm/pwm-sl28cpld.c | 204 +++++++++++
drivers/watchdog/Kconfig | 11 +
drivers/watchdog/Makefile | 1 +
drivers/watchdog/sl28cpld_wdt.c | 242 +++++++++++++
include/linux/gpio-regmap.h | 88 +++++
include/linux/ioport.h | 5 +
include/linux/mfd/core.h | 26 +-
include/linux/regmap.h | 10 +
34 files changed, 2142 insertions(+), 32 deletions(-)
create mode 100644 Documentation/devicetree/bindings/gpio/kontron,sl28cpld-gpio.yaml
create mode 100644 Documentation/devicetree/bindings/hwmon/kontron,sl28cpld-hwmon.yaml
create mode 100644 Documentation/devicetree/bindings/mfd/kontron,sl28cpld.yaml
create mode 100644 Documentation/devicetree/bindings/pwm/kontron,sl28cpld-pwm.yaml
create mode 100644 Documentation/devicetree/bindings/watchdog/kontron,sl28cpld-wdt.yaml
create mode 100644 Documentation/hwmon/sl28cpld.rst
create mode 100644 drivers/gpio/gpio-regmap.c
create mode 100644 drivers/gpio/gpio-sl28cpld.c
create mode 100644 drivers/hwmon/sl28cpld-hwmon.c
create mode 100644 drivers/irqchip/irq-sl28cpld.c
create mode 100644 drivers/mfd/sl28cpld.c
create mode 100644 drivers/pwm/pwm-sl28cpld.c
create mode 100644 drivers/watchdog/sl28cpld_wdt.c
create mode 100644 include/linux/gpio-regmap.h
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Add a new function regmap_add_irq_chip_np() with its corresponding
devm_regmap_add_irq_chip_np() variant. Sometimes one want to register
the IRQ domain on a different device node that the one of the regmap
node. For example when using a MFD where there are different interrupt
controllers and particularly for the generic regmap gpio_chip/irq_chip
driver. In this case it is not desireable to have the IRQ domain on
the parent node.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200402203656.27047-5-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
When executing the following command, we met kernel dump.
dmesg -c > /dev/null; cd /sys;
for i in `ls /sys/kernel/debug/regmap/* -d`; do
echo "Checking regmap in $i";
cat $i/registers;
done && grep -ri "0x02d0" *;
It is because the count value is too big, and kmalloc fails. So add an
upper bound check to allow max size `PAGE_SIZE << (MAX_ORDER - 1)`.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1584064687-12964-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When checking if a register block is writable we must ensure that the
block does not start with or contain a non incrementing register.
Fixes: 8b9f9d4dc5 ("regmap: verify if register is writeable before writing operations")
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Link: https://lore.kernel.org/r/20200118205625.14532-1-ben.whitten@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Only two changes for this release, one fix for error handling with
runtime PM and a change from Greg removing error handling from debugfs
API calls now that they implement user visible error reporting.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl1+vGATHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0JMJB/9Nx/DQ8mGc4KTiNjOd2ic0nwPfsYNB
Nr7/5GXmvjPc64tLmDDITZZTNbruMxMfcvJqli+JVre/yVbM8DrGMuPKpV7KJQl1
ZKXCeRfXRtsZ/u3e/Kek0GEDRGgSwp1qTR3e4SoEQYyrf8oWIrVfRn53ptF+xJld
inQh81+uoLHjWLZ+B2JQ/Dx7729z1+cmM3xpttvakDDRBJ7d9kIs2XA6mNfcWx4/
JibNoOdRt+xxU2ALaa2yNEomv/AuFbQARYop2w6ivxefQAYpVAdqwnYJJdAHIZXi
vkBczdLQpLeGXLaDrR6v0nvKvNBKaUH2WU2osFHI8ww9+HWEVr834Xor
=UQDg
-----END PGP SIGNATURE-----
Merge tag 'regmap-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Only two changes for this release, one fix for error handling with
runtime PM and a change from Greg removing error handling from debugfs
API calls now that they implement user visible error reporting"
* tag 'regmap-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap-irq: Correct error paths in regmap_irq_thread for pm_runtime
regmap: no need to check return value of debugfs_create functions
