Defining iounmap() with arguments prevents it from being used as a
function pointer, causing platforms to work around this. Instead,
define it to be a simple macro.
Do the same for __arch_io(re|un)map too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds support for Buffalo Linkstation Live v3 (LS-CHL) NAS drives.
Signed-off-by: Ash Hughes <ashley.hughes@blueyonder.co.uk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Wrong MPP configuration would cause <cpu>_mpp_conf loop infinitely
because the mpp list iterator would not be incremented.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
The type was IORESOURCE_IO which is not what is expected by
plat_nand_probe(). This device has not worked since 2d098a72
("mtd: plat_nand: request memory resource before doing ioremap").
Signed-off-by: Michael Spang <mspang@csclub.uwaterloo.ca>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
These three platforms didn't properly fill nr_chips in gen_nand
registration and therefore depended on gen_nand bug fixed by commit
81cbb0b177 ("mtd: gen_nand: fix support for
multiple chips")
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The code to support the DNS-323 rev C1 added a call to
phy_register_fixup_for_uid() and therefore phylib has to
be built in.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Some platforms, such as the DNS-323 rev C requires the soft reset line
to be toggled on and back off for the reset to work.
Note: The choice of 200ms delay comes from the 2.6.12 based vendor kernel.
It seems to be a -lot- though and I had my device working fine with much
smaller delays but better safe...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This patch adds the base support for this new HW revision to the existing
dns323-setup.c file. The SoC seems to be the same as rev B1, the GPIOs
are all wired differently though and the fan control isn't i2c based
anymore.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Among other changes, commit b2a731aa ("D-link DNS-323 revision A1 power
LED") changed the default behaviour of the power LED from solid to
blinking. This was done to match the original DNS-323 firmware which
blinks during the boot process and sets the LED to solid when booting
has completed. However, the downside of this behaviour is that it
requires userland code to change the LED, even for those who don't
care about the behaviour of the original firmware. Therefore, change
it to solid again and let those who care about the original behaviour
change the behaviour from userland.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
The leds-gpio blink_set() callback follows the same prototype as the
main leds subsystem blink_set() one.
The problem is that to stop blink, normally, a leds driver does it
in the brightness_set() callback when asked to set a new fixed value.
However, with leds-gpio, the platform has no hook to do so, as this
later callback results in a standard GPIO manipulation.
This changes the leds-gpio specific callback to take a new argument
that indicates whether the LED should be blinking or not and in what
state it should be set if not. We also update the dns323 platform
which seems to be the only user of this so far.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Since commit b2a731aa5c, dns323_init() is
setting the power led gpio direction with gpio_direction_output() but
doesn't request the gpio before (which is not permitted by the gpio
layer afaik). This behaviour is triggering a WARN() at boot time.
Tested-by: Christian Samsel <csamsel@gmxpro.de>
Cc: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
[ Part 2: "Attached Text" ]
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
"Input: add KEY_WPS_BUTTON definition" introduced
a generic keycode for WPS input events.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Makes it consistent with VMALLOC_START
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes the power LED on DNS-323 revision A1, and adds timer
support for (hopefully) both A1 and B1 revisions.
Power LED on revision A1 is active low and also requires GPIO 4 to be
low to work.
Tested on my DNS-323 revision A1.
I have set the default trigger to timer as that replicates the
behaviour of the original firmware, userspace can change the trigger
at the end of the boot process providing a useful indication that
booting has completed.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch allow user-space to configure the switch power-off behaviour
via the gpiolib sysfs interface.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The (void *) cast is not needed when setting dev.platform_data to the
address of the data. Remove the casts.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch fixes power LED blinking and power-off on DNS-323 rev. B1.
GPIO pin 3 has to be set to 1 to stop power LED blinking and to allow the LED to be controlled via leds-gpio. This pin has to be also set to 1 for power-off to work.
To power-off the rev. B1 machine, pin 8 has to be set to 1 and then set to 0 to do actual power-off.
Tested on my DNS-323 rev. B1
Signed-off-by: Erik Benada <erikbenada@yahoo.ca>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch add support for the 2Big Network LaCie boards.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
On the 88f6183, orion5x's setup_cpu_win() fails to ever program any
mbus bridge remap registers, which causes transactions for PCI/PCIe
IO/MEM space to get sent to random mbus targets. Adding a check for
the 6183 in orion5x_cpu_win_can_remap() is necessary and sufficient
to make PCIe wlan cards work on the 6183 reference design.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch add support for the d2 Network and the Big Disk Network
LaCie boards.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Acked-by: Christopher Moore <moore@free.fr>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Without incrementing the counter the next window setup will overwrite
the SRAM mapping.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The security accelerator which can act as a puppet player for the crypto
engine requires its commands in the sram. This patch adds support for the
phys mapping and creates a platform device for the actual driver.
[ nico: renamed device name from "mv,orion5x-crypto" to "mv_crypto"
so to match the module name and be more generic for Kirkwood use ]
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch adds support for the switch found on the Netgear
WNR854T router.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The Orion watchdog driver is also used on Kirkwood.
Convention is to use orion5x for stuff specific to 88F5xxx Orion chips
and simply "orion" for shared stuff across SoCs including Kirkwood.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The name of the define for the Reset-Out-Mask register as well as its
bit for the watchdog reset are changed to match the names used for
Kirkwood (which in turn match the processor specification more
closely). There is no functional change.
This patch prepares for adding orion5x_wdt as a platform device to
Kirkwood.
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Add hook so that the HW RNG source on the TS-78xx is available.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Since commit eb0519b5a1, mv643xx_eth is non functional on ARM because
the platform device declaration does not include any coherent DMA mask
and coherent memory allocations fail.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Remove explicit names from platform device resources since they will
automatically be named after the platform device they're associated
with.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Symbols like SOFT_RESET are way too generic to be exported at large.
To avoid this, let's move the mbus bridge register defines into a
separate file and include it where needed. This affects mach-kirkwood,
mach-loki, mach-mv78xx0 and mach-orion5x simultaneously as they all
share code in plat-orion which relies on those defines.
Some other defines have been moved to narrower scopes, or simply deleted
when they had no user.
This fixes compilation problem with mpt2sas on the above listed
platforms.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1750 commits)
ixgbe: Allow Priority Flow Control settings to survive a device reset
net: core: remove unneeded include in net/core/utils.c.
e1000e: update version number
e1000e: fix close interrupt race
e1000e: fix loss of multicast packets
e1000e: commonize tx cleanup routine to match e1000 & igb
netfilter: fix nf_logger name in ebt_ulog.
netfilter: fix warning in ebt_ulog init function.
netfilter: fix warning about invalid const usage
e1000: fix close race with interrupt
e1000: cleanup clean_tx_irq routine so that it completely cleans ring
e1000: fix tx hang detect logic and address dma mapping issues
bridge: bad error handling when adding invalid ether address
bonding: select current active slave when enslaving device for mode tlb and alb
gianfar: reallocate skb when headroom is not enough for fcb
Bump release date to 25Mar2009 and version to 0.22
r6040: Fix second PHY address
qeth: fix wait_event_timeout handling
qeth: check for completion of a running recovery
qeth: unregister MAC addresses during recovery.
...
Manually fixed up conflicts in:
drivers/infiniband/hw/cxgb3/cxio_hal.h
drivers/infiniband/hw/nes/nes_nic.c
The orion5x-wdt driver is now registered as a platform device and
receives the tclk value as platform data. This fixes a compile issue
cause by a previously removed define "ORION5X_TCLK".
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Kristof Provost <kristof@sigsegv.be>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Martin Michlmayr <tbm@cyrius.com>
Cc: Sylver Bruneau <sylver.bruneau@googlemail.com>
Cc: Kunihiko IMAI <bak@d2.dion.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Received official word finally from Technological Systems on which
FPGA ID's they have released unto the world. Also an additional of
a dummy entry matching the FPGA ID of the Verilog template on our
wiki.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The initial version of the DSA driver only supported a single switch
chip per network interface, while DSA-capable switch chips can be
interconnected to form a tree of switch chips. This patch adds support
for multiple switch chips on a network interface.
An example topology for a 16-port device with an embedded CPU is as
follows:
+-----+ +--------+ +--------+
| |eth0 10| switch |9 10| switch |
| CPU +----------+ +-------+ |
| | | chip 0 | | chip 1 |
+-----+ +---++---+ +---++---+
|| ||
|| ||
||1000baseT ||1000baseT
||ports 1-8 ||ports 9-16
This requires a couple of interdependent changes in the DSA layer:
- The dsa platform driver data needs to be extended: there is still
only one netdevice per DSA driver instance (eth0 in the example
above), but each of the switch chips in the tree needs its own
mii_bus device pointer, MII management bus address, and port name
array. (include/net/dsa.h) The existing in-tree dsa users need
some small changes to deal with this. (arch/arm)
- The DSA and Ethertype DSA tagging modules need to be extended to
use the DSA device ID field on receive and demultiplex the packet
accordingly, and fill in the DSA device ID field on transmit
according to which switch chip the packet is heading to.
(net/dsa/tag_{dsa,edsa}.c)
- The concept of "CPU port", which is the switch chip port that the
CPU is connected to (port 10 on switch chip 0 in the example), needs
to be extended with the concept of "upstream port", which is the
port on the switch chip that will bring us one hop closer to the CPU
(port 10 for both switch chips in the example above).
- The dsa platform data needs to specify which ports on which switch
chips are links to other switch chips, so that we can enable DSA
tagging mode on them. (For inter-switch links, we always use
non-EtherType DSA tagging, since it has lower overhead. The CPU
link uses dsa or edsa tagging depending on what the 'root' switch
chip supports.) This is done by specifying "dsa" for the given
port in the port array.
- The dsa platform data needs to be extended with information on via
which port to reach any given switch chip from any given switch chip.
This info is specified via the per-switch chip data struct ->rtable[]
array, which gives the nexthop ports for each of the other switches
in the tree.
For the example topology above, the dsa platform data would look
something like this:
static struct dsa_chip_data sw[2] = {
{
.mii_bus = &foo,
.sw_addr = 1,
.port_names[0] = "p1",
.port_names[1] = "p2",
.port_names[2] = "p3",
.port_names[3] = "p4",
.port_names[4] = "p5",
.port_names[5] = "p6",
.port_names[6] = "p7",
.port_names[7] = "p8",
.port_names[9] = "dsa",
.port_names[10] = "cpu",
.rtable = (s8 []){ -1, 9, },
}, {
.mii_bus = &foo,
.sw_addr = 2,
.port_names[0] = "p9",
.port_names[1] = "p10",
.port_names[2] = "p11",
.port_names[3] = "p12",
.port_names[4] = "p13",
.port_names[5] = "p14",
.port_names[6] = "p15",
.port_names[7] = "p16",
.port_names[10] = "dsa",
.rtable = (s8 []){ 10, -1, },
},
},
static struct dsa_platform_data pd = {
.netdev = &foo,
.nr_switches = 2,
.sw = sw,
};
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OMAP wishes to pass state to the boot loader upon reboot in order to
instruct it whether to wait for USB-based reflashing or not. There is
already a facility to do this via the reboot() syscall, except we ignore
the string passed to machine_restart().
This patch fixes things to pass this string to arch_reset(). This means
that we keep the reboot mode limited to telling the kernel _how_ to
perform the reboot which should be independent of what we request the
boot loader to do.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Stefan Agner found his board comes with 0x00b480/0x02 but the main
board also has Rev B printed on it like my 0x00b480/0x03. Some light
enum renaming was needed but it was to be expected.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This data should be passed to the xor driver in order to initialize
the address decoding windows of the xor unit. without this patch, the
self tests of the xor will fail unless the address decoding windows were
initialized by the boot loader.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Added checks to the platform_device_(register|add) calls so that if
a device failed to load it would then not later be unloaded; also
added the hooks so that it would not try to unload when the RTC
driver support is compiled out.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Signed-off-by: Nicolas Pitre <nico@cam.org>
The GPIO interrupts can be configured as either level triggered or edge
triggered, with a default of level triggered. When an edge triggered
interrupt is requested, the gpio_irq_set_type method is called which
currently switches the given IRQ descriptor between two struct irq_chip
instances: orion_gpio_irq_level_chip and orion_gpio_irq_edge_chip. This
happens via __setup_irq() which also calls irq_chip_set_defaults() to
assign default methods to uninitialized ones. The problem is that
irq_chip_set_defaults() is called before the irq_chip reference is
switched, leaving the new irq_chip (orion_gpio_irq_edge_chip in this
case) with uninitialized methods such as chip->startup() causing a kernel
oops.
Many solutions are possible, such as making irq_chip_set_defaults() global
and calling it from gpio_irq_set_type(), or calling __irq_set_trigger()
before irq_chip_set_defaults() in __setup_irq(). But those require
modifications to the generic IRQ code which might have adverse effect on
other architectures, and that would still be a fragile arrangement.
Manually copying the missing methods from within gpio_irq_set_type()
would be really ugly and it would break again the day new methods with
automatic defaults are added.
A better solution is to have a single irq_chip instance which can deal
with both edge and level triggered interrupts. It is also a good idea
to switch the IRQ handler instead, as the edge IRQ handler allows for
one edge IRQ event to be queued as the IRQ is actually masked only when
that second IRQ is received, at which point the hardware can queue an
additional IRQ event, making edge triggered interrupts a bit more
reliable.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
the FPGA on the TS-7800 provides access to a number of devices
and so we have to be careful when reprogramming it. As we
are effectively turning a bus off/on we have to inform the
kernel that it should stop using anything provided by the
FPGA (currently only the RTC however the NAND, LCD, etc is
to come) before it's reprogrammed.
Once reprogramed, we can tell the kernel to (re)enable things
by checking the FPGA ID against a lookup table for what a
particular FPGA bitstream can provide.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
The TS-7800's M25P40 is not available to the kernel, it's used
to load the initial bitstream onto the FPGA and so these hooks
point to nothing and need to be removed.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Split off Orion GPIO handling code into plat-orion/, and add
support for multiple sets of (32) GPIO pins.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The 88F5182 found in the DNS-323 rev B1 (and some other devices, such
as the CH3SNAS) require different initialisation of the SATA
controller and MPP registers.
Tested on a DNS-323 rev B1.
Signed-off-by: Matt Palmer <mpalmer@hezmatt.org>
Based on similar code from the tsx09 series of machines, just rips the MAC
address out of flash and stuffs it into the NIC. Tested on a DNS323 rev B1.
It's possible (though unlikely) that an A1 will have the MAC in a different
location in flash.
Signed-off-by: Matt Palmer <mpalmer@hezmatt.org>
The Orion ehci driver serves the Orion, kirkwood and DD Soc families.
Since each of those integrate a different USB phy we should have the
ability to use few initialization sequences or to leave the boot loader
phy settings as is.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
As Al did for Versatile in 2ad4f86b60,
add a typesafe __io implementation for platforms to use. Convert
platforms to use this new simple typesafe implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When ISA_DMA_API is unset, we're not implementing the ISA DMA API,
so there's no point in publishing the prototypes via asm/dma.h, nor
including the machine dependent parts of that API.
This allows us to remove a lot of mach/dma.h files which don't contain
any useful code. Unfortunately though, some platforms put their own
private non-ISA definitions into mach/dma.h, so we leave these behind
and fix the appropriate #include statments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Let's provide an overridable default instead of having every machine
class define __virt_to_bus and __bus_to_virt to the same thing. What
most platforms are using is bus_addr == phys_addr so such is the default.
One exception is ebsa110 which has no DMA what so ever, so the actual
definition is not important except only for proper compilation. Also
added a comment about the special footbridge bus translation.
Let's also remove comments alluding to set_dma_addr which is not
(and should not) be commonly used.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to the documentation gpio_free should only be called from task
context only. To make this more explicit add a might sleep to all
implementations.
This patch changes the gpio_free implementations for the arm architecture.
DaVinci is skipped on purpose to simplify the merge process for patches
switching it over to use gpiolib as per request by David Brownell.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 2ede90ca78500ca0ffeee19d7812d345f8ad152d adds 6183 support,
but the SPI support in there doesn't work since it depends on a
6183 SPI unit erratum fix that only just went upstream, via commit
2bec19feab.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This adds DSA switch instantiation hooks to the orion5x and the
kirkwood ARM SoC platform code, and instantiates the DSA switch
driver on the 88F5181L FXO RD, the 88F5181L GE RD, the 6183 AP GE
RD, the Linksys WRT350n v2, and the 88F6281 RD boards.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
This patch allows the use of the hardware watchdog in the
Marvell Orion series of ARM SoCs.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
desc_handle_irq() was declared as obsolete since long ago.
Replace it with generic_handle_irq()
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds specific power-off method for Buffalo Linkstation Mini
board. The board has a hardware switch which should be monitored from
userspace. When the switch is in OFF position the board should be rebooted
and U-Boot will start in an idle mode and wait for the user to move the
power switch back to ON position.
Signed-off-by: Alexey Kopytko <alexey@kopytko.ru>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch adds support for Buffalo Linkstation Mini board.
Signed-off-by: Alexey Kopytko <alexey@kopytko.ru>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch provides standard GPIO LED control
for the ED Mini V2, with software blinking only
(CPLD hardware blinking capability is not used).
This patch also provides status of the power
button as a standard GPIO input event.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The RD88F6183AP-GE is an access point reference design for the
88F6183 SoC, with a 88E6161 six-port gigabit ethernet switch with
five PHYs (providing 1 WAN and 4 LAN ports and an interface to the
CPU), and a mini-PCIe slot for a wireless card.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The Orion-1-90 (88F6183) is another member of the Orion SoC family,
which has a 16 bit DDR2 interface, one x1 PCIe port (configurable as
Root Complex or Endpoint), one 10/100/1000 ethernet interface, one
USB 2.0 port with PHY, one SPDIF/I2S interface, one SDIO interface,
one TWSI interface, two UARTs, one SPI interface, a NAND controller,
a crypto engine, and a 4-channel DMA engine.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
This patch adds support for the Buffalo Terastation Pro II/Live.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
This patch adds support for the LaCie Ethernet Disk mini V2.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Signed-off-by: Christopher Moore <moore@free.fr>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Currently, orion5x uses a hardcoded timer tick rate of 166 MHz, but
the actual timer tick rate varies between different members of the SoC
family (and can vary based on strap pin settings).
This patch prepares for runtime determination of the timer tick rate.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Wire up the ethernet port's error interrupt so that the
mv643xx_eth driver can sleep for SMI event completion instead of
having to busy-wait for it.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Currently, there are two different fields in the
mv643xx_eth_platform_data struct that together describe the PHY
address -- one field (phy_addr) has the address of the PHY, but if
that address is zero, a second field (force_phy_addr) needs to be
set to distinguish the actual address zero from a zero due to not
having filled in the PHY address explicitly (which should mean
'use the default PHY address').
If we are a bit smarter about the encoding of the phy_addr field,
we can avoid the need for a second field -- this patch does that.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Register UART1 on QNAP TS-209 and TS-409 because the PIC controller
is connected to it. This fixes a regression from 2.6.26.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The lm75 driver was recently converted to the new-style binding,
so now it can be loaded from the DNS-323 support code.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Tested-by: Tobias Poschwatta <tp@fonz.de>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Flash needs to be set up before we can try to read the MAC address
from there.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The Kurobox Pro crashes when any of the PCI controller registers
are accessed. This patch adds a function to the Orion PCI handling
code that board support code can call to disable enumerating the
PCI bus entirely, and makes the Kurobox Pro PCI-related init code
call this function.
Signed-off-by: Per Andersson <avtobiff@gmail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The reset button on the QNAP TS-409 is available through gpio.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Use key codes for the buttons on the TS-209/TS-409 that make more
sense than the current values.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Byron Bradley <byron.bbradley@gmail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Export the four red SATA LEDs on the QNAP TS-409 that are connected
through gpio. Since the boot loader apparently sets the SATA LEDs 2-4
to red and the SATA LED can only be red or green (but not both),
exporting the red SATA LEDs (which automatically turns them off upon
boot) makes the green SATA presence/activity indication visible.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
On D0 5281 SoCs, we need to disable the wait-for-interrupt
instruction due to an erratum.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Martin Michlmayr <tbm@cyrius.com>
This patch performs the equivalent include directory shuffle for
plat-orion, and fixes up all users.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1].
Remove them completely. Sed script for the reference:
s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g
s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g
s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g
s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g
s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g
s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g
s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g
s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_PROBE/IRQ_TYPE_PROBE/g
s/IRQT_NOEDGE/IRQ_TYPE_NONE/g
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mv643xx_eth hardware has a provision for polling the PHY's
MII management registers to obtain the (R)(G)MII interface speed
(10/100/1000) and duplex (half/full) and pause (off/symmetric)
settings to use to talk to the PHY.
The driver currently does not make use of this feature. Instead,
whenever there is a link status change event, it reads the current
link parameters from the PHY, and programs those parameters into
the mv643xx_eth MAC by hand.
This patch switches the mv643xx_eth driver to letting the MAC
auto-determine the (R)(G)MII link parameters by PHY polling, if there
is a PHY present. For PHYless ports (when e.g. the (R)(G)MII
interface is connected to a hardware switch), we keep hardcoding the
MII interface parameters.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The HP mv2120 has several LEDs that are controlled through gpio.
Export the health LED, the red SATA LEDs as well as two gpios
that control the brightness of _all_ LEDs to userland. The
Ethernet and power LEDs can't be controlled through gpio and the
blue SATA LEDs are handled via the SATA driver.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch adds support for the Marvell Orion-VoIP RD-88F5181L-FXO
Reference Design, and enables use of the ethernet, USB, Cardbus and
mini-PCIe ports.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This patch adds support for the Marvell Orion-VoIP RD2-88F5181L-GE
Reference Design, and enables use of the ethernet, USB, Cardbus and
mini-PCIe ports.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The Cardbus connector does not have an IDSEL signal, and Cardbus
cards are always the intended target of configuration transactions
on their local PCI bus. This means that if the Orion's PCI bus
signals are hooked up to a Cardbus slot, the same set of PCI
functions will will appear 31 times, for each of the PCI device
IDs 1-31 (ID 0 is the host bridge).
This patch adds a function to the Orion PCI handling code that board
support code can call to enable Cardbus mode. When Cardbus mode is
enabled, configuration transactions on the PCI local bus are only
allowed to PCI IDs 0 (host bridge) and 1 (cardbus device).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
In some cases, compilation of the tsx09 common file was failing due
to an incomplete list of includes.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
After Jean Delvare's change "i2c: Convert most new-style drivers
to use module aliasing" (3760f73671),
loading rtc-xxx from platform code fails. Update mv2120-setup.c so
that the driver is loaded correctly.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Kurobox Pro/Linkstation Pro devices use a microcontroller connected
to UART1. As most of the communication with this microcontroller is
done from userland (power button detection, fan speed ...), the setup
file has to make UART1 available from userland.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
This patch adds support for the Maxtor Shared Storage II hardware.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
This patch implements the communication with the microcontroller on the
Kurobox Pro and Linkstation Pro/Live boards. This is allowing to send
the commands needed to power-off the board correctly.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The mv643xx_eth platform data field ->force_phy_addr only needs
to be set if the passed-in ->phy_addr field is zero (to distinguish
the case of not having specified a phy address
(force_phy_addr = 0) from the case where a phy address of zero needs
to be used (force_phy_addr = 1.))
Also, the ->force_phy_addr field will hopefully disappear in a
future mv643xx_eth reorganisation.
Therefore, this patch deletes the ->force_phy_addr field initialiser
from all Orion board code.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
If all PCI devices are working as expected, the error printks in the
various implementations of ->map_irq() doesn't really provide any
useful info. And if something is not working as expected, turning
on pci=debug gives you more useful information than the printk calls
in ->map_irq(), since the former also tells you which devices _did_
get IRQs successfully assigned. Therefore, delete these printks
entirely.
Spotted by Russell King.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Instead of having board code poke directly into the MPP configuration
registers, and separately calling orion5x_gpio_set_valid_pins() to
indicate which MPP pins can be used as GPIO pins, introduce a helper
function for configuring the roles of each of the MPP pins, and have
that helper function handle gpio validity internally.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
It makes no sense to do PCIe WA window setup in the individual
board support files while the decision whether or not to use the
PCIe WA access method is made in a different place, in the PCIe
support code.
This patch moves the configuration of a PCIe WA window from the
individual Orion board support files to the central Orion PCIe
support code.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
This patch moves initialisation of EHCI/I2C/UART platform devices
from the common orion5x_init() into the board support code.
The rationale behind this is that only the board support code knows
whether certain peripherals have been brought out on the board, and
not initialising peripherals that haven't been brought out is
desirable for example:
- to reduce user confusion (e.g. seeing both 'eth0' and 'eth1'
appear while there is only one ethernet port on the board); and
- to allow for future power savings (peripherals that have not
been brought out can be clock gated off entirely).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
The DRAM base address and size fields in the CPU's MBUS bridge have
64KiB granularity, instead of the currently used 16MiB. Since all
of the currently supported MBUS peripherals support 64KiB granularity
as well, this patch changes the Orion address map code to stop
rounding base addresses down and sizes up to multiples of 16MiB.
Found by Ke Wei <kewei@marvell.com>.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Currently, Orion window setup uses hardcoded window indexes for each
of the boot/cs0/cs1/cs2/PCIe WA windows. The static window allocation
used can clash if board support code will ever attempt to configure
both a dev2 and a PCIe WA window, as both of those use CPU mbus window
#7 at present.
This patch keeps track of the last used window, and opens subsequently
requested windows sequentially, starting from 4. (Windows 0-3 are used
as MEM/IO windows for the PCI/PCIe buses.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
More cosmetic cleanup:
- Replace 8-space indents by proper tab indents.
- In structure initialisers, use a trailing comma for every member.
- Collapse "},\n{" in structure initialiers to "}, {".
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Whereas most Orion 5x machine support code would initialise the PCI
subsystem with nr_controllers in their struct hw_pci set to 2, the
DNS323 and Kurobox Pro machine support code had nr_controllers set
to 1.
This was presumably done because on those two machines, the PCI(-X)
controller (nr == 1) isn't used, requiring initialisation of only
the PCIe controller (nr == 0.) However, not initialising the PCI(-X)
controller on boards that don't use it leads to a situation where
both the PCIe and the PCI(-X) controller think that their root bus is
zero, and it messes up IRQ assignment.
This patch changes the DNS323 and Kurobox Pro support code to always
use nr_controllers == 2.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch cleans up Orion's addr-map.c a bit after all peripheral
window programming code has been moved out into the relevant drivers.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Pass the Orion TCLK tick rate into the ethernet driver.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Make the Orion 5x platform code use the mbus window handling code
that's in the mv643xx_eth driver, instead of programming the GigE
block's mbus window registers by hand.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
Move mv643xx_eth's static state (ethernet register block base address
and MII management interface spinlock) into a struct hanging off the
shared platform device. This is necessary to support chips that
contain multiple mv643xx_eth silicon blocks.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Unify a couple more spellings of "PCIe" ("PCI-E", "PCIE".)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
End addresses in 'struct resource' are inclusive -- fix the common
orion5x code to pass in the proper end addresses when instantiating
the two on-chip EHCI controllers.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The current orion5x board ->map_irq() routines check whether a
given bus number lives on the PCIe controller by comparing it with
the PCIe controller's primary bus number. This doesn't work in
case there are multiple buses in the PCIe domain, i.e. if there
exists a PCIe bridge on the primary PCIe bus.
This patch adds a helper function (orion5x_pci_map_irq()) that
returns the IRQ number for the given PCI device if that device has
a hard-wired IRQ, or -1 otherwise, and makes each board's
->map_irq() function use this helper function.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The Buffalo Linkstation Pro/Live is the same hardware as the
Kurobox Pro but without the NAND flash. This patch adds a
second MACHINE_START macro to the Kurobox setup file to minimise
code duplication.
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The bootloader on ts209 Orion boards doesn't configure the right
ethernet MAC address into the GigE unit on boot. The only way to
get the MAC address is by parsing it from the 'NAS Config' flash
partition, which is an ext2 partition that contains a file which
holds the MAC address in plain text (format "xx:xx:xx:xx:xx:xx\n")
-- this patch does that.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Cc: Byron Bradley <byron.bbradley@gmail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Do a global s/orion/orion5x/ of the Orion 5x-specific bits (i.e.
not the plat-orion bits.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
