Allow generic frame-buffer code to correctly write texts and blit images for
1, 2 and 4 bit per pixel frame-buffer organizations when pixels in bytes are
organized to in opposite order than bytes in long type.
Overhead should be reasonable. If option is not selected, than compiler
should eliminate completely all overhead.
The feature is disabled at compile time if CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is
not set.
[adaplas]
Convert helper functions to macros if feature is not enabled.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a few nvidia hardware where the i2c port assignments are reversed,
i.e., the 1st i2c port is assigned to the secondary display and the 2nd i2c
port to the primary display. In most cases, if only 1 display is attached, or
if only 1 flatpanel and 1 analog display is attached, the port reversal is of
no consequence. However if 2 flatpanels are attached, it can cause display
problems.
There is no sane way of determining if the hardware reversed the i2c port
assignment, so the simplest fix is to add a boot/module option, "reverse_i2c
to explicitly reverse the i2c port.
This also restores i2c ordering back to the pre-2.6.22 state.
Signed-off-by: Antonino Daplas <adaplas@gail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, if the refresh rate is not specified, fb_find_mode() returns the
first known video mode with the requested resolution, which provides no
guarantees wrt the refresh rate. Change this so that the mode with the
highest refresh rate is returned when the driver provides a custom video mode
database and the monitor limits, and a mode with the safe 60 Hz refresh rate
otherwise.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel framebuffer now supports interlaced video modes.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changed things:
1. vmalloc()/vfree() replaced with rvmalloc()/rvfree() (taken from
drivers/media/video/se401.c)
2. mmap method implemented (mostly taken from drivers/media/video/se401.c)
3. smem_start and smem_len fields of struct fb_fix_screeninfo initialized.
(smem_start initialized with virtual address, don't know if it is really
bad...)
[adaplas: sparse warning fix]
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch:
- disallows setting of virtual height above 2048 as it does
not work for accelerated copyarea and imageblit
- fixes blinking of pm2v cursor by pushing cursor outside
the display (x=2047)
- fixes hardware cursor position on Permedia 2 chips with
panning enabled
- enables hardware cursor by default
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds hardware cursor support for the Permedia 2 chip.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes:
- redundant fields from the cirrusfb_regs structure
- one redundant header
- fixes two includes ("" to <>)
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch does some "short-range" code improvements like merging identical
switch clauses, replacing conditional branches with calculation of values,
merging only once-used functions into place they are called from.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes unused or redundant fields from cirrusfb_info structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces "typedef enum" with "enum type" constructs. Using the
typedef is error for the checkpatch.pl script.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes over 850 errors and warnings pointed out by the checkpatch.pl
script.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes mode selection to always prefer default mode if possible
and always honor type of display set by default mode settings.
This patch is required in case the same display modes were defined for
different panels (e.g. STN and TFT).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes lcdcon1 register field from the s3c2410fb_display as all
bits are calculated from other fields.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds pixelclock field to the s3c2410fb_display structure and make
use of it in the driver.
The Bast machine defined 9 modes but pixclock and margin values are defined
only for the 640x480 modes so I removed other modes.
This patch also fixes wrong display type constant for the SMDK2440 board.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch:
- moves more display mode preparations to s3c2410fb_check_var()
- reduces number of fields in s3c2410fb_info
- removes redundant values setting in s3c2410fb_probe()
- removes static mach_info pointer
- releases fb_info structure in s3c2410fb_remove()
- changes s3c2410fb_init to __init from __devinit
- fixes few typos in comments and removes unused includes
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces <asm/uaccess.h> with <linux/uaccess.h> after the
checkpatch.pl hint. The include of <asm/uaccess.h> is removed if the driver
does not use it.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Akpm's patch "newport_con warning fix" got me to look at the console drivers
again and one thing that I noticed was that none of the fonts was using ISO
initializers for it's fonts.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
atyfb: Move the pseudo palette into the card-specific atyfb_par, so it's no
longer shared among multiple cards
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch sets correct bits related to the byte ordering of the
framebuffer. This was tested on little endian kernel only. The big endian
kernel may require different settings.
The patch also adds 32 bpp mode which is called 24 bpp by Samsung. One
pixel takes 32 bits but only 24 bits are used in this mode.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds missing virtual register offsets where
appropriate. This fixes crashes in the driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes unused lcdcon2 and lcdcon3 register value
from the s3c2410fb_display structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds synchronization pulse lenght fields to
the s3c2410fb_display structure and makes use of them
in the driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes use of vertical margins fields in
the s3c2410fb_display structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes unused lcdcon3 register from the
s3c2410fb_display structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes use of margins fields in the s3c2410fb_display
structure.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a new structure to describe and handle
more than one panel (display mode) for the s3c2410 framebuffer.
This structure is added after the pxafb driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes redundant fb field from
the s3c2410fb_info structure. This breaks circular
reference fb_info -> s3c2410fb_info -> fb_info again.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch cleans up the driver a bit. It contains
coding style fixes (pointed by Lindent and checkpatch),
white space clean ups and few minor code improvements.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds hardware cursor support to the pm3fb driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds hardware cursor support for Permedia 2V chips.
The hardware cursor is disabled by default. It does not blink - the
same issue is mentioned in the x11 driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Looking at the code flow, `int first' in fb_create_modedb() should be static.
[adaplas]
Better for 'int first' to be moved outside the loop.
[akpm@linux-foundation.org: kill stray semicolon]
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes all errors detected by checkpatch.pl script in the pm3fb.c
file.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes all errors detected by checkpatch.pl script in the pm2fb.c
file.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds mtrr support to the tdfxfb driver. It also kills one
redundant include and initialization value.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds hardware cursor support to the tdfxfb driver.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch improves source code mainly by killing redundant variable loads,
reducing number of variables, simplifying conditional branches, etc.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported by: John Lumby <johnlumby@hotmail.com>
Some of the entries in the mode database does not match the comments and/or
the refresh field. Adjust the timings so they match with both the comments
and the refresh rate.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The logo code is not and should not be used by modules.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
radeon_driver_vblank_do_wait() can become static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes 3 issues:
- transparency handling in tdfxfb
- panning with more than 4096 virtual height and acceleration (acceleration
with x & y > 4096)
- exit paths on errors in tdfxfb_probe()
Additionally it sets a FBINFO_READS_FAST flag to use smart blitter scrolling
(speed up on tdfxfb).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch contains coding style improvements to the tdfxfb driver (white
spaces, indentations, long lines).
It also moves fb_ops structure to the end of file, so forward declarations of
ops functions are redundant.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch contains coding style improvements to the tridentfb driver (white
spaces, indentations, long lines).
It also moves fb_ops structure after fb api functions are defined.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the other three palette formats possible with
the PXA LCD controller. This is required on boards where an LCD is connected
with all its 18 bits. With this patch, it's possible to use an 8-bit mode
with 18-bit palette entries. This used to be possible in 2.4 kernels but
disappeared in 2.6. With current kernels, you can only get wrong colours
out of an LCD connected this way.
Users can choose the palette format by doing something like this
in their board definition:
static struct pxafb_mach_info my_fb_info = {
[...]
.lccr3 = LCCR3_OutEnH | LCCR3_PixFlEdg | LCCR3_PDFOR_3,
.lccr4 = LCCR4_PAL_FOR_2,
[...]
};
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This contains the following changes:
* Overlay surface alpha is configured separately from the overlay. This
prevents display glitches (configure and fill the overlay first, set
alpha to a visible value next)
* Added an ioctl for configuring transparency of the Overlay and graphics
planes. Blend mode, colorkey mode and global alpha mode are supported.
* Added an ioctl for setting the plane order. The overlay plance can be placed
over or
under the graphics plane.
* Added an ioctl for setting and reading chip registers, with mask.
* Updated copyright for 2007
[adaplas]
* Coding style changes
Signed-off-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we setup the panel interface whilst configuring the
framebuffer, we should ensure the panel interface is not
in tristate, in case the bootloader or previous setup has
not enabled it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Call the fb_set_suspend() over suspend and resume.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The suspend and resume code is failing to restore the CRT control
register, thus causing the CRT data-path to get changed if the
SM501 experiences a reset over suspend.
Also move some of the debug messages to dev_dbg() level and ensure
that the suspend code does not try and restore anything it did not
manage to save.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds accelerated fillrect for 24-bit depth.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch:
- initializes correctly the Permedia2V chip if it is not initialized by BIOS
- puts back clock frequency for the ELSA WINNER board to 100kHz
- fixes returned error values from setcolreg() function
- uses more general classes for PCI ids
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch concentrates on source compacting, simplification and more
conformance to kernel coding standards.
The major changes:
- RD32() and WR() functions are merged into pm2_RD() and pm2_WR()
- conditional (with switch()) RDAC functions are separated in two
unconditional ones
- the conditional pm2fb_block_op() function is merged into pm2fb_fillrect()
and pm2fb_copyarea()
- WAIT_FIFO() values are corrected
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds usage of MTRR registers and two new options: noaccel and
nomtrr.
[bunk@kernel.org: make pm3fb_init() static again]
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch contains improvements:
- it adds ROP_XOR in pm3fb_fillrect()
- it conforms closer to coding style
- it removes redundant parentheses and setting bits with 0 value
- it checks if hardware acceleration is disabled in pm3fb_imageblit
- it adds module description
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch contains 3 small improvements:
- it corrects scan line width calculation in pm3fb_imageblit()
- it corrects mmio mapping for big endian machines
- it enables panning acceleration constants
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the pm3_imageblit() restriction to blit only images with
width divisable by 32.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes constants named AAA_DISABLE with value 0. They are redudant
and misleading ( a |= AAA_DISABLE does nothing and usually should be
a &= ~AAA_ENABLE).
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch corrects name of the field.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds accelerated copyarea and partially accelerated imageblit
functions. There is also fixed one register address in the pm3fb.h file.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
uvesafb is an enhanced version of vesafb. It uses a userspace helper (v86d)
to execute calls to the x86 Video BIOS functions. The driver is not limited
to any specific arch and whether it works on a given arch or not depends on
that arch being supported by the userspace daemon. It has been tested on
x86_32 and x86_64.
A single BIOS call is represented by an instance of the uvesafb_ktask
structure. This structure contains a buffer, a completion struct and a
uvesafb_task substructure, containing the values of the x86 registers, a flags
field and a field indicating the length of the buffer. Whenever a BIOS call
is made in the driver, uvesafb_exec() builds a message using the uvesafb_task
substructure and the contents of the buffer. This message is then assigned a
random ack number and sent to the userspace daemon using the connector
interface.
The message's sequence number is used as an index for the uvfb_tasks array,
which provides a mapping from the messages coming from userspace to the
in-kernel uvesafb_ktask structs.
The userspace daemon performs the requested operation and sends a reply in the
form of a uvesafb_task struct and, optionally, a buffer. The seq and ack
numbers in the reply should be exactly the same as those in the request.
Each message from userspace is processed by uvesafb_cn_callback() and after
passing a few sanity checks leads to the completion of a BIOS call request.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Paulo Marques <pmarques@grupopie.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make fb_destroy_modelist an exported symbol for use in the uvesafb driver.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/char/rtc.c allowed RTC_PIE_ON ioctls for non-root users, as long as
the current interval (set via RTC_IRQP_SET) is <= max_user_freq. Allow
RTC_PIE_ON under the same conditions when /dev/rtc* is handled by the rtc
subsystem.
Signed-off-by: Bryan Kadzban <bryan@kdzbn.homelinux.net>
Acked-by: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/char/rtc.c exposed a sysctl to change the maximum frequency at
which a non-root user could ask the RTC to generate interrupts (via the
RTC_IRQP_SET ioctl). This value is no longer available under the new RTC
subsystem, so add it to sysfs for each RTC device.
Works for me on x86_64 (both reads and writes), using rtc-cmos.
Signed-off-by: Bryan Kadzban <bryan@kdzbn.homelinux.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some cleanups for the rtc-cmos probe logic:
- Claim i/o ports with request_region() not request_resource(),
for better coexistence betwen platform and pnp bus glues.
- Claim those ports earlier, to help work around procfs bugs
(it allows duplicate names, like /proc/driver/rtc).
- Fix some glitches in cleanup code, notably a cut'n'paste-o
where the i/o port region might not get released during
cleanup after a probe fault.
And some comment clarifications, including noting that this code
must work with PNPBIOS not just PNPACPI..
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix readback of RTC alarms on platforms which return -1 in
non-hardware-supported RTC alarm fields.
To fill in the missing (-1) values, we grab an RTC timestamp along with the
RTC alarm value, and use the timestamp fields to populate the missing alarm
fields.
To counter field-wrap races (since the timestamp and alarm are not read
together atomically), we read the RTC timestamp both before and after
reading the RTC alarm value, and then check for wrapped fields --> if any
have wrapped, we know we have a possible inconsistency, so we loop and
reread the timestamp and alarm again.
Wrapped fields in the RTC timestamps are an issue because rtc-cmos.c, for
example, also gets/uses an RTC timestamp internally while fetching the RTC
alarm. If our timestamp here wasn't the same (minutes and higher) as what
was used internally there, then we might end up populating the -1 fields
with inconsistent values.
This fixes readbacks from /sys/class/rtc/rtc?/wakealarm, as well as other
code paths which call rtc_read_alarm().
Signed-off-by: Mark Lord <mlord@pobox.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds an RTC class driver for the Maxim/Dallas 1374 RTC chip,
based on drivers/i2c/chips/ds1374.c. It supports alarm functionality.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not all i2c adapters support I2C-level messaging. Check that the adapter
does before probing for a PCF8583 chip, as the driver makes use of
i2c_transfer and i2c_master_send.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc-ds1742 platform driver name doesn't match its module name,
which might prevents it from properly hotplugging. There is only two
in-tree user of its driver, which are fixed by this patch too.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc-ds1553 platform driver name doesn't match its module name, which
might prevent it from properly hotplugging. This driver has no in-tree
users.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In rtc-dev.c, when a rtc device is opened, file->private_data is already
attached with the rtc device pointer, so there is no need to call
to_rtc_device() to convert file->private_data to a rtc device pointer.
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Mark Zhan <rongkai.zhan@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RTC periodic IRQs are only defined to work for 2^N Hz values. This patch
moves that validity check into the infrastructure, so drivers don't need to
check it; and adds kerneldoc for the two interface functions related to
periodic IRQs. (One of which was quite mysterious until its first use was
recently checked in!)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add kernel/kernel and kernel/user locking for the periodic irq feature of
the rtc class.
PIE ioctls are also supported.
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In drivers/isdn/capi/kcapi.c::old_capi_manufacturer(), if the call to
get_capi_ctr_by_nr(ldef.contr); in line 823 returns NULL, then we'll be
dereferencing a NULL pointer in the very next line.
(Found by Coverity checker as bug #402)
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we fail to allocate an skb in
drivers/isdn/capi/capidrv.c::send_message(), then we'll end up
dereferencing a NULL pointer.
Since out of memory conditions are not unheard of, I believe it
is better to print a error message and just return rather than
bring down the whole kernel.
Sure, doing this may upset some application, but that's still
better than crashing the whole system.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ISDN subsystem common functions use a semaphore as mutex. Use the
mutex API instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove pointless taking of spinlock around reading a single pointer-sized
or smaller variable.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the SPI framework and drivers stop using class_device. Update docs
accordingly ... highlighting just which sysfs paths should be
"safe"/stable.
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, all QE SPI controllers are almost the same comparing to
MPC83xx's, thus let's use that driver for them.
Tested to work on MPC85xx in loopback mode.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Shrink the runtime footprint of various SPI drivers:
- Move the probe() routine into the init section where practical,
using platform_driver_probe() to make that safe. This often saves
around 1KB. Using platform_driver_probe() can also be a correctness
fix, if the probe routine is already marked __init but the driver
struct keeps a dangling pointer to it after init section removal.
- Likewise move remove() routines into the exit sections.
These changes would be inappropriate iff the platform devices were
actually hotpluggable (e.g. they're found on optional addon cards,
or in an FPGA that's dynamically reprogrammed). In these cases,
that's not the situation; it's an SOC controller and the only device
is initialized before these drivers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch cleans up duplicate includes in
drivers/spi/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add code to connect to the DCA driver and provide cpu tags for use by
drivers that would like to use Direct Cache Access hints.
[Adrian Bunk] Several Kconfig cleanup items
[Andrew Morten, Chris Leech] Fix for using cpu_physical_id() even when
built for uni-processor
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Direct Cache Access (DCA) is a method for warming the CPU cache before data
is used, with the intent of lessening the impact of cache misses. This
patch adds a manager and interface for matching up client requests for DCA
services with devices that offer DCA services.
In order to use DCA, a module must do bus writes with the appropriate tag
bits set to trigger a cache read for a specific CPU. However, different
CPUs and chipsets can require different sets of tag bits, and the methods
for determining the correct bits may be simple hardcoding or may be a
hardware specific magic incantation. This interface is a way for DCA
clients to find the correct tag bits for the targeted CPU without needing
to know the specifics.
[Dave Miller] use DEFINE_SPINLOCK()
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for MSI and MSI-X interrupt handling, including the ability
to choose the desired interrupt method.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
[bunk@kernel.org: drivers/dma/ioat_dma.c: make 3 functions static]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Split the general PCI startup from the DMA handling code in order to
prepare for adding support for DCA services and future versions of the
ioatdma device.
[Rusty Russell] Removal of __unsafe() usage.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Take care of a bunch of little code nits in ioatdma files
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename the ioatdma.c file in preparation for splitting into multiple files,
which will allow for easier adding new functionality.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add device ids for new revs of the Intel I/OAT DMA engine
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove an unused symbol M32R_SIO_SHARE_IRQS from drivers/serial/m32r_sio.h.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Cc: "Robert P. J. Day" <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a per node state sysfs class attribute file to /sys/devices/system/node
to display node state masks.
E.g., on a 4-cell HP ia64 NUMA platform, we have 5 nodes: 4 representing
the actual hardware cells and one memory-only pseudo-node representing a
small amount [512MB] of "hardware interleaved" memory. With this patch, in
/sys/devices/system/node we see:
#ls -1F /sys/devices/system/node
has_cpu
has_normal_memory
node0/
node1/
node2/
node3/
node4/
online
possible
#cat /sys/devices/system/node/possible
0-255
#cat /sys/devices/system/node/online
0-4
#cat /sys/devices/system/node/has_normal_memory
0-4
#cat /sys/devices/system/node/has_cpu
0-3
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The checks for node_online in the uncached allocator are made to make sure
that memory is available on these nodes. Thus switch all the checks to use
N_HIGH_MEMORY and to N_ONLINE.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Jes Sorensen <jes@sgi.com>
Acked-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Bob Picco <bob.picco@hp.com>
Cc: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@skynet.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Partial write can be easily supported by LO_CRYPT_NONE mode, but it is not
easy in LO_CRYPT_CRYPTOAPI case, because of its block nature. I don't know
who still used cryptoapi, but theoretically it is possible. So let's leave
things as they are. Loop device doesn't support partial write before
Nick's "write_begin/write_end" patch set, and let's it behave the same way
after.
Signed-off-by: Dmitriy Monakhov <dmonakhov@openvz.org>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are intended to replace prepare_write and commit_write with more
flexible alternatives that are also able to avoid the buffered write
deadlock problems efficiently (which prepare_write is unable to do).
[mark.fasheh@oracle.com: API design contributions, code review and fixes]
[akpm@linux-foundation.org: various fixes]
[dmonakhov@sw.ru: new aop block_write_begin fix]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Dmitriy Monakhov <dmonakhov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commit b5810039a5 contains the note
A last caveat: the ZERO_PAGE is now refcounted and managed with rmap
(and thus mapcounted and count towards shared rss). These writes to
the struct page could cause excessive cacheline bouncing on big
systems. There are a number of ways this could be addressed if it is
an issue.
And indeed this cacheline bouncing has shown up on large SGI systems.
There was a situation where an Altix system was essentially livelocked
tearing down ZERO_PAGE pagetables when an HPC app aborted during startup.
This situation can be avoided in userspace, but it does highlight the
potential scalability problem with refcounting ZERO_PAGE, and corner
cases where it can really hurt (we don't want the system to livelock!).
There are several broad ways to fix this problem:
1. add back some special casing to avoid refcounting ZERO_PAGE
2. per-node or per-cpu ZERO_PAGES
3. remove the ZERO_PAGE completely
I will argue for 3. The others should also fix the problem, but they
result in more complex code than does 3, with little or no real benefit
that I can see.
Why? Inserting a ZERO_PAGE for anonymous read faults appears to be a
false optimisation: if an application is performance critical, it would
not be doing many read faults of new memory, or at least it could be
expected to write to that memory soon afterwards. If cache or memory use
is critical, it should not be working with a significant number of
ZERO_PAGEs anyway (a more compact representation of zeroes should be
used).
As a sanity check -- mesuring on my desktop system, there are never many
mappings to the ZERO_PAGE (eg. 2 or 3), thus memory usage here should not
increase much without it.
When running a make -j4 kernel compile on my dual core system, there are
about 1,000 mappings to the ZERO_PAGE created per second, but about 1,000
ZERO_PAGE COW faults per second (less than 1 ZERO_PAGE mapping per second
is torn down without being COWed). So removing ZERO_PAGE will save 1,000
page faults per second when running kbuild, while keeping it only saves
less than 1 page clearing operation per second. 1 page clear is cheaper
than a thousand faults, presumably, so there isn't an obvious loss.
Neither the logical argument nor these basic tests give a guarantee of no
regressions. However, this is a reasonable opportunity to try to remove
the ZERO_PAGE from the pagefault path. If it is found to cause regressions,
we can reintroduce it and just avoid refcounting it.
The /dev/zero ZERO_PAGE usage and TLB tricks also get nuked. I don't see
much use to them except on benchmarks. All other users of ZERO_PAGE are
converted just to use ZERO_PAGE(0) for simplicity. We can look at
replacing them all and maybe ripping out ZERO_PAGE completely when we are
more satisfied with this solution.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus "snif" Torvalds <torvalds@linux-foundation.org>
We have flags to indicate whether a section actually has a valid mem_map
associated with it. This is never set and we rely solely on the present bit
to indicate a section is valid. By definition a section is not valid if it
has no mem_map and there is a window during init where the present bit is set
but there is no mem_map, during which pfn_valid() will return true
incorrectly.
Use the existing SECTION_HAS_MEM_MAP flag to indicate the presence of a valid
mem_map. Switch valid_section{,_nr} and pfn_valid() to this bit. Add a new
present_section{,_nr} and pfn_present() interfaces for those users who care to
know that a section is going to be valid.
[akpm@linux-foundation.org: coding-syle fixes]
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Notebook manufacturer seems to built a newer Wacom pen enabled tablet to
recent tablet pcs which are not recognized by the serial pnp driver.
Attached is a patch which makes the newer Wacom WACF007 and WACF008 tablets
useable with the serial driver. The device is fully compatible with it.
Signed-off-by: Maik Broemme <mbroemme@plusserver.de>
Cc: Andrey Panin <pazke@orbita1.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The UPF_FIXED_PORT flags was introduced in 2.6.22 and it can be used
instead of the driver specific verify_port routine.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable wakeup from serial ports, make it run-time configurable over sysfs,
e.g.,
echo enabled > /sys/devices/platform/serial8250.0/tty/ttyS0/power/wakeup
Requires
# CONFIG_SYSFS_DEPRECATED is not set
Following suggestions from Alan and Russell moved the may_wake_up checks
to serial_core.c. This time actually tested - it does even work. Could
someone, please, verify, that put_device after device_find_child is
correct?
Also would be nice to test with a Natsemi UART, that can wake up the system,
if such systems exist.
For this you just have to apply the patch below, issue the above "echo"
command to one of your Natsemi port, suspend and resume your system, and
verify that your Natsemi port still works. If you are actually capable of
waking up the system from that port, would be nice to test that as well.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for a whole range of boards. Some are partly autodetected but
not fully correctly others (PCI Express notably) not at all. Stick all
the right entries in.
Thanks to Mainpine for information and testing.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not include some header files already indluded by serial_core.h.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most non cardbus devices can't do dma, so flag them as such in the device
creation routine.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Natalie Protasevich <protasnb@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for Sierra Wireless AC850 which has the same Ids as the
AC710/750 but has a different firmware.
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on a patch by Haavard Skinnemoen posted to linux-pcmcia, but using
static inlines for readability reasons. this should fix PCMCIA an AVR32
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only a few definitions is in xxs1500.h .
They can be move to au1000_xxs1500.c .
[m.kozlowski@tuxland.pl: fix unbalanced parenthesis]
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently I've been trying to get working PCMCIA interface on H5000 ipaq
series, using dual PCMCIA sleeve. So far things work correctly, but I had
to do one modification to drivers/pcmcia/pxa2xx_base.c to get the interface
working with orinoco gold PCMCIA card (wired pcnet_cs ethernet card worked
even without this modification).
The issue has something to do with assert time on PCMCIA bus, but I'm not
really sure what -- I found the working value just by trial&error approach.
I'm not sure how is the assert value in pxa2xx_mcxx_asst calculated (I
know, simple formula, but the reason why is it calculated that way is not
obvious for me), neither that my modification is correct. It just works
with iPAQ.
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dm-crypt used the ->bi_size member in the bio endio handling to
free the appropriate pages, but it frees all of it from both call
paths. With the ->bi_end_io() changes, ->bi_size was always 0 since
we don't do partial completes. This caused dm-crypt to leak memory.
Fix this by removing the size argument from crypt_free_buffer_pages().
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Otherwise we could have junk in the sg fields, fooling
the sg chaining into thinking ->page is valid.
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
LIBATA_MAX_PRD is the maximum number of DMA scatter/gather elements
permitted by the HBA's DMA engine. It's properly set to
q->max_hw_segments via the sg_tablesize parameter.
libata shouldn't call blk_queue_max_phys_segments. Now LIBATA_MAX_PRD
is equal to SCSI_MAX_PHYS_SEGMENTS by default (both is 128), so
everything is fine. But if they are changed, some code (like the scsi
mid layer, sg chaining, etc) might not work properly.
(Addition from Jens) The basic issue is that the physical segment
setting is purely a driver issue. And since SCSI is managing the sglist,
libata has no business changing the setting. All libata should care
about is the hw segment setting.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This reverts sg segment size ifdefs that the current code has in order
to provide a way to reduce sgpool memory consumption.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This option is true if a low-level driver can support sg
chaining. This will be removed eventually when all the drivers are
converted to support sg chaining. q->max_phys_segments is set to
SCSI_MAX_SG_SEGMENTS if false.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
ips properly uses scsi_for_each_sg for the normal I/O path, however,
the breakup path doesn't.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
[PATCH] USB storage: sg chaining support
Modify usb_stor_access_xfer_buf() to take a pointer to an sg
entry pointer, so we can keep track of that instead of passing
around an integer index (which we can't use when dealing with
multiple scatterlist arrays).
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This converts libata to using the sg helpers for looking up sg
elements, instead of doing it manually.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This is what enables large commands. If we need to allocate an
sgtable that doesn't fit in a single page, allocate several
SCSI_MAX_SG_SEGMENTS sized tables and chain them together.
SCSI defaults to large chained sg tables, if the arch supports it.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Just pass in the command, no point in passing in the scatterlist
and scatterlist pool index seperately.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This converts the SCSI mid layer to using the sg helpers for looking up
sg elements, instead of doing it manually.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The recent bio work and subsequent fixups created unused variables.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix USB docbook warnings.
Warning(linux-2.6.23-git8//include/linux/usb/gadget.h:487): No description found for parameter 'g'
Warning(linux-2.6.23-git8//include/linux/usb/gadget.h:506): No description found for parameter 'g'
Warning(linux-2.6.23-git8//drivers/usb/core/hub.c:1416): No description found for parameter 'usb_dev'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix libata docbook warnings.
Warning(linux-2.6.23-git8//drivers/ata/libata-scsi.c:3251): No description found for parameter 'dev'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix kernel-api docbook warnings.
Warning(linux-2.6.23-git8//drivers/message/fusion/mptscsih.c:2618): No description found for parameter 'sc'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (95 commits)
[ARM] 4578/1: CM-x270: PCMCIA support
[ARM] 4577/1: ITE 8152 PCI bridge support
[ARM] 4576/1: CM-X270 machine support
[ARM] pxa: Avoid pxa_gpio_mode() in gpio_direction_{in,out}put()
[ARM] pxa: move pxa_set_mode() from pxa2xx_mainstone.c to mainstone.c
[ARM] pxa: move pxa_set_mode() from pxa2xx_lubbock.c to lubbock.c
[ARM] pxa: Make cpu_is_pxaXXX dependent on configuration symbols
[ARM] pxa: PXA3xx base support
[NET] smc91x: fix PXA DMA support code
[SERIAL] Fix console initialisation ordering
[ARM] pxa: tidy up arch/arm/mach-pxa/Makefile
[ARM] Update arch/arm/Kconfig for drivers/Kconfig changes
[ARM] 4600/1: fix kernel build failure with build-id-supporting binutils
[ARM] 4599/1: Preserve ATAG list for use with kexec (2.6.23)
[ARM] Rename consistent_sync() as dma_cache_maint()
[ARM] 4572/1: ep93xx: add cirrus logic edb9307 support
[ARM] 4596/1: S3C2412: Correct IRQs for SDI+CF and add decoding support
[ARM] 4595/1: ns9xxx: define registers as void __iomem * instead of volatile u32
[ARM] 4594/1: ns9xxx: use the new gpio functions
[ARM] 4593/1: ns9xxx: implement generic clockevents
...
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits)
[IPV6]: Consolidate the ip6_pol_route_(input|output) pair
[TCP]: Make snd_cwnd_cnt 32-bit
[TCP]: Update the /proc/net/tcp documentation
[NETNS]: Don't panic on creating the namespace's loopback
[NEIGH]: Ensure that pneigh_lookup is protected with RTNL
[INET]: kmalloc+memset -> kzalloc in frag_alloc_queue
[ISDN]: Fix compile with CONFIG_ISDN_X25 disabled.
[IPV6]: Replace sk_buff ** with sk_buff * in input handlers
[SELINUX]: Update for netfilter ->hook() arg changes.
[INET]: Consolidate the xxx_put
[INET]: Small cleanup for xxx_put after evictor consolidation
[INET]: Consolidate the xxx_evictor
[INET]: Consolidate the xxx_frag_destroy
[INET]: Consolidate xxx_the secret_rebuild
[INET]: Consolidate the xxx_frag_kill
[INET]: Collect common frag sysctl variables together
[INET]: Collect frag queues management objects together
[INET]: Move common fields from frag_queues in one place.
[TG3]: Fix performance regression on 5705.
[ISDN]: Remove local copy of device name to make sure renames work.
...
There are standard keycodes for brightness and volume; map the events to
emit them so that things work properly
Signed-off-by: Jeremy Katz <katzj@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (40 commits)
Input: use full RCU API
Input: remove tsdev interface
Input: add support for Blackfin BF54x Keypad controller
Input: appletouch - another fix for idle reset logic
HWMON: hdaps - switch to using input-polldev
Input: add support for SEGA Dreamcast keyboard
Input: omap-keyboard - don't pretend we support changing keymap
Input: lifebook - fix X and Y axis range
Input: usbtouchscreen - add support for GeneralTouch devices
Input: fix open count handling in input interfaces
Input: keyboard - add CapsShift lock
Input: adbhid - produce all CapsLock key events
Input: ALPS - add signature for ThinkPad R61
Input: jornada720_kbd - send MSC_SCAN events
Input: add support for the HP Jornada 7xx (710/720/728) touchscreen
Input: add support for HP Jornada 7xx onboard keyboard
Input: add support for HP Jornada onboard keyboard (HP6XX)
Input: ucb1400_ts - use schedule_timeout_uninterruptible
Input: xpad - fix dependancy on LEDS class
Input: auto-select INPUT for MAC_EMUMOUSEBTN option
...
Resolved conflicts manually in drivers/hwmon/applesmc.c: converting from
a class device to a device and converting to use input-polldev created a
few apparently trivial clashes..
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] pata_pcmcia: Add additional id string (corsair, 1GB)
libata: prevent devices with blank model names from being DMA blacklisted
ata_piix: SATA 2port controller port map fix
pata_cs5536: ATA driver for Geode companion chip
libata: add ST9160821AS / 3.CCD to NCQ blacklist
libata: fix revalidation issuing after configuration commands
[libata] sata_nv: add SW NCQ support for MCP51/MCP55/MCP61
[libata] pata_sil680: Add MMIO support
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (35 commits)
xen-netfront: rearrange netfront structure to separate tx and rx
netdev: convert non-obvious instances to use ARRAY_SIZE()
ucc_geth: Fix build break introduced by commit 09f75cd7bf
gianfar: Fix regression caused by new napi interface
gianfar: Cleanup compile warning caused by 0795af57
gianfar: Fix compile regression caused by bea3348e
add new prom.h for AU1x00
update AU1000 get_ethernet_addr()
MIPSsim: General cleanup
Jazzsonic: Fix warning about unused variable.
Remove msic_dcr_read() in axon_msi.c
Use dcr_host_t.base in dcr_unmap()
Add dcr_host_t.base in dcr_read()/dcr_write()
Use dcr_host_t.base in ibm_emac_mal
Update ibm_newemac to use dcr_host_t.base
tehuti: possible leak in bdx_probe
TC35815: Fix build
SAA9730: Fix build
AR7 ethernet
myri10ge: update driver version to 1.3.2-1.287
...
The variable CPPFLAGS is a wellknown variable and the usage by
kbuild may result in unexpected behaviour.
This patch replace use of CPPFLAGS with KBUILD_CPPFLAGS all over the
tree and enabling one to use:
make CPPFLAGS=...
to specify additional CPP commandline options.
Patch was tested on following architectures:
alpha, arm, i386, x86_64, mips, sparc, sparc64, ia64, m68k, s390
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Keep tx and rx elements separate on different cachelines to prevent
bouncing.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Atari keyboard: incorporate additional review comments:
o Kill reference to source file name
o Return error value from input_register_device() instead of -ENOMEM
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Michael Schmitz <schmitz@biophys.uni-duesseldorf.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This will convert remaining non-obvious or naive calculations of array
sizes to use ARRAY_SIZE() macro.
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When the loopback device is failed to initialize inside the new
namespaces, panic() is called. Do not do it when the namespace
in question is not the init_net.
Plus cleanup the error path a bit.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 90833fdab8 ("[ARM] 4554/1: replace
consistent_sync() with flush_ioremap_region()") introduced a new
"flush_ioremap_region()" function to be used by the MTD mainstone-flash
and lubbock-flash drivers to fix a regression from around 2.6.18.
Those drivers were independently merged into a single driver by Todd
Poynor in commit e644f7d628 ("[MTD] MAPS:
Merge Lubbock and Mainstone drivers into common PXA2xx driver")
Later, those two commits were merged into the main MTD tree by commit
b160292cc2 ("Merge Linux 2.6.23") by David
Woodhouse, but in that merge, the fix to use flush_iomap_region() got
lost (as it was to files that now no longer existed).
This reinstates the fix in the new driver.
Noticed-by: Russell King <rmk@arm.linux.org.uk>
Tested-and-acked-by: Nicolas Pitre <nico@cam.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jared Hulbert <jaredeh@gmail.com>
Cc: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Mon, Oct 15, 2007 at 06:44:56PM +0400, Denis V. Lunev wrote:
Compilation fix. The problem appears after
7c076d1de869256848dacb8de0050a3a390f95df by Karsten Keil <kkeil@suse.de>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the gdth module is loaded (or compiled in), the gdth_timeout function
gets started even if no actual gdth controllers are found b the probing.
That ends up not only being unnecessary, but also causes a crash due to
the function blindly just trying to pick the first entry off the
"gdth_instances" list, and accessing it - which obviously doesn't work
if the list is empty!
Noticed by Ingo Molnar.
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The strn_pattern_cmp routine does not handle a blank name parameter
properly. The only patterns which should match a blank name are "*"
and an explicit "". If the function is passed a blank name in current
code, it will always match against the patt parameter. The bug manifests
itself as the device with the empty model name always matching the first
device in the DMA blacklist, forcing it to revert to PIO mode.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds a port map for ICH9 and ICH8 SATA controllers that have only 2 ports available in that mode.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a driver for the ATA controller on the Geode CS5536 companion
chip. The PCI device ID for this device was previously claimed by
pata_amd.c but the PIO timings were not correct. This driver also
works around a bug in some BIOSes that handle unaligned access to the
PCI config registers poorly. Finally, the driver allows fallback to
using MSR registers for configuration on BIOSes that are truly
broken.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A performance regression was introduced by the following commit:
commit ee6a99b539
Author: Michael Chan <mchan@broadcom.com>
Date: Wed Jul 18 21:49:10 2007 -0700
[TG3]: Fix msi issue with kexec/kdump.
In making that change, the PCI latency timer and cache line size
registers were not restored after chip reset. On the 5705, the
latency timer gets reset to 0 during chip reset and this causes
very poor performance.
Update version to 3.84.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By the time we get to that switch by PHY type, we have 8bit
value. No need to keep it in u64 when u8 would do.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commands which can change device configuration, EH is scheduled
to revalidate and reconfigure the device. Host link was incorrectly
used unconditionally when scheduling EH action. This resulted in
bogus revalidation request and mismatched configuration between device
and driver. Fix it.
This bug was reported by Igor Durdanovic.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Igor Durdanovic <idurdanovic@comcast.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the Software NCQ support to sata_nv.c for MCP51/MCP55/MCP61 SATA
controller. NCQ function is disable by default, you can enable it
with 'swncq=1'. NCQ will be turned off if the drive is Maxtor on
MCP51 or MCP55 rev 0xa2 platform.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Kuan Luo <kluo@nvidia.com>
Signed-off-by: Peer Chen <pchen@nvidia.com>
Cc: Zoltan Boszormenyi <zboszor@dunaweb.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds MMIO support to the pata_sil680 for taskfile IOs,
based on what the old siimage does.
I haven't bothered changing the chip setup stuff from PCI config
cycles to MMIO though (siimage does it), I don't think it matters,
I've only adapted it to use MMIO for taskfile accesses.
I've tested it on a Cell blade and it seems to work fine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/ucc_geth.c: In function 'ucc_geth_rx':
drivers/net/ucc_geth.c:3483: error: 'dev' undeclared (first use in this function)
drivers/net/ucc_geth.c:3483: error: (Each undeclared identifier is reported only once
drivers/net/ucc_geth.c:3483: error: for each function it appears in.)
make[2]: *** [drivers/net/ucc_geth.o] Error 1
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Protect all new napi function calls with CONFIG_GFAR_NAPI. Otherwise
the driver will stop working when CONFIG_GFAR_NAPI disabled.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update AU1000 get_ethernet_addr().
Three functions were brought together in one.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
General cleanups mostly as suggested by checkpatch plus getting rid of
homebrew version of offsetof().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Caused by "[NET]: Introduce and use print_mac() and DECLARE_MAC_BUF()"
aka 0795af5729.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With the base stored in dcr_host_t, there's no need for callers to pass
the dcr_n into dcr_unmap(). In fact this removes the possibility of them
passing the incorrect value, which would then be iounmap()'ed.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that all users of dcr_read()/dcr_write() add the dcr_host_t.base, we
can save them the trouble and do it in dcr_read()/dcr_write().
As some background to why we just went through all this jiggery-pokery,
benh sayeth:
Initially the goal of the dcr_read/dcr_write routines was to operate like
mfdcr/mtdcr which take absolute DCR numbers. The reason is that on 4xx
hardware, indirect DCR access is a pain (goes through a table of
instructions) and it's useful to have the compiler resolve an absolute DCR
inline.
We decided that wasn't worth the API bastardisation since most places
where absolute DCR values are used are low level 4xx-only code which may
as well continue using mfdcr/mtdcr, while the new API is designed for
device "instances" that can exist on 4xx and Axon type platforms and may
be located at variable DCR offsets.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This requires us to do a sort-of fake dcr_map(), so that base is set
properly. This will be fixed/removed when the device-tree-aware emac driver
is merged.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that dcr_host_t contains the base address, we can use that in the
ibm_newemac code, rather than storing it separately.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
bea3348eef broke the build of tc35815.c
for the non-NAPI case:
CC drivers/net/tc35815.o
drivers/net/tc35815.c: In function 'tc35815_interrupt':
drivers/net/tc35815.c:1464: error: redefinition of 'lp'
drivers/net/tc35815.c:1443: error: previous definition of 'lp' was here
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix build breakage by the recent statistics cleanup in cset
09f75cd7bf.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
New version which uses less locking and drops old API
Signed-off-by: Matteo Croce <technoboy85@gmail.com>
Signed-off-by: Eugene Konev <ejka@imfi.kspu.ru>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update myri10ge firmware headers to latest upstream version with
TSO6 and RSS support.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix one comment in myri10ge.c and update indendation and white spaces
to match the code generated by indent from upstream CVS.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the "don't change MAC of slaves" functionality added in
previous changes to be a generic option, rather than something tied to
IB devices, as it's occasionally useful for regular ethernet devices as
well.
Adds "fail_over_mac" option (which is automatically enabled for IB
slaves), applicable only to active-backup mode.
Includes documentation update.
Updates bonding driver version to 3.2.0.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When bonding enslaves non Ethernet devices it takes pointers to functions
in the module that owns the slaves. In this case it becomes unsafe
to keep the bonding master registered after last slave was unenslaved
because we don't know if the pointers are still valid. Destroying the bond when slave_cnt is zero
ensures that these functions be used anymore.
Signed-off-by: Moni Shoua <monis at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Delay sending a gratuitous_arp when LINK_STATE_LINKWATCH_PENDING bit
in dev->state field is on. This improves the chances for the arp packet to
be transmitted.
Signed-off-by: Moni Shoua <monis at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
bonding sometimes uses Ethernet constants (such as MTU and address length) which
are not good when it enslaves non Ethernet devices (such as InfiniBand).
Signed-off-by: Moni Shoua <monis at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allow to enslave devices when the bonding device is not up. Over the discussion
held at the previous post this seemed to be the most clean way to go, where it
is not expected to cause instabilities.
Normally, the bonding driver is UP before any enslavement takes place.
Once a netdevice is UP, the network stack acts to have it join some multicast groups
(eg the all-hosts 224.0.0.1). Now, since ether_setup() have set the bonding device
type to be ARPHRD_ETHER and address len to be ETHER_ALEN, the net core code
computes a wrong multicast link address. This is b/c ip_eth_mc_map() is called
where for multicast joins taking place after the enslavement another ip_xxx_mc_map()
is called (eg ip_ib_mc_map() when the bond type is ARPHRD_INFINIBAND)
Signed-off-by: Moni Shoua <monis at voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch allows for enslaving netdevices which do not support
the set_mac_address() function. In that case the bond mac address is the one
of the active slave, where remote peers are notified on the mac address
(neighbour) change by Gratuitous ARP sent by bonding when fail-over occurs
(this is already done by the bonding code).
Signed-off-by: Moni Shoua <monis at voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch changes some of the bond netdevice attributes and functions
to be that of the active slave for the case of the enslaved device not being
of ARPHRD_ETHER type. Basically it overrides those setting done by ether_setup(),
which are netdevice **type** dependent and hence might be not appropriate for
devices of other types. It also enforces mutual exclusion on bonding slaves
from dissimilar ether types, as was concluded over the v1 discussion.
IPoIB (see Documentation/infiniband/ipoib.txt) MAC address is made of a 3 bytes
IB QP (Queue Pair) number and 16 bytes IB port GID (Global ID) of the port this
IPoIB device is bounded to. The QP is a resource created by the IB HW and the
GID is an identifier burned into the HCA (i have omitted here some details which
are not important for the bonding RFC).
Signed-off-by: Moni Shoua <monis at voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When the bonding device senses a carrier loss of its active slave it replaces
that slave with a new one. In between the times when the carrier of an IPoIB
device goes down and ipoib_neigh is destroyed, it is possible that the
bonding driver will send a packet on a new slave that uses an old ipoib_neigh.
This patch detects and prevents this from happenning.
Signed-off-by: Moni Shoua <monis at voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com>
Acked-by: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
IPoIB uses a two layer neighboring scheme, such that for each struct neighbour
whose device is an ipoib one, there is a struct ipoib_neigh buddy which is
created on demand at the tx flow by an ipoib_neigh_alloc(skb->dst->neighbour)
call.
When using the bonding driver, neighbours are created by the net stack on behalf
of the bonding (master) device. On the tx flow the bonding code gets an skb such
that skb->dev points to the master device, it changes this skb to point on the
slave device and calls the slave hard_start_xmit function.
Under this scheme, ipoib_neigh_destructor assumption that for each struct
neighbour it gets, n->dev is an ipoib device and hence netdev_priv(n->dev)
can be casted to struct ipoib_dev_priv is buggy.
To fix it, this patch adds a dev field to struct ipoib_neigh which is used
instead of the struct neighbour dev one, when n->dev->flags has the
IFF_MASTER bit set.
Signed-off-by: Moni Shoua <monis at voltaire.com>
Signed-off-by: Or Gerlitz <ogerlitz at voltaire.com>
Acked-by: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_enable_device() is __must_check so do that in natsemi_resume().
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Unless we have failed to fill the RX ring the timer used by the natsemi
driver is not particularly urgent and can use round_jiffies() to allow
grouping with other timers.
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch provides support for PCMCIA on CM-X270
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch provides core support for CM-X270 platform.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PXA DMA support code for smc91x doesn't pass a struct device to
the dma_*map_single() functions, which leads to an oops in the dma
bounce code. We have a struct device which was used to probe the
SMC chip. Use it.
(This patch is slightly larger because it requires struct smc_local
to move into the header file.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure pm callback is called upon initialisation to place port in
correct power saving state. Ensure console is initialised prior
to deciding whether to power down the port.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'agp-patches' of master.kernel.org:/pub/scm/linux/kernel/git/airlied/agp-2.6:
fix use after free in amd create gatt pages
AGP fix race condition between unmapping and freeing pages
* 'drm-patches' of ssh://master.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
via invalid device ids removal
radeon: Commit the ring after each partial texture upload blit.
i915: fix vbl swap allocation size.
drm: Replace DRM_IOCTL_ARGS with (dev, data, file_priv) and remove DRM_DEVICE.
drm: remove XFREE86_VERSION macros.
drm: Replace filp in ioctl arguments with drm_file *file_priv.
drm: Remove DRM_ERR OS macro.
Fix bogus copying of data into userspace when HIDIOCGRDESC is issued.
HID-transport layer makes sure that dev->hid->rdesc is not larger than
HID_MAX_DESCRIPTOR_SIZE.
Noticed-by: Al Viro <viro@ftp.linux.org.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
0x1106, 0x7204 is unknown and thus is not an IGP/GPU.
0x1106, 0x3304 is K8M800 hostbridge, not an IGP/GPU.
None of them are in drm git tree.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This makes sure each blit starts as early as possible, which may improve
texture upload performance in some cases.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The data is now in kernel space, copied in/out as appropriate according to t
This results in DRM_COPY_{TO,FROM}_USER going away, and error paths to deal
with those failures. This also means that XFree86 4.2.0 support for i810 DR
is lost.
Signed-off-by: Dave Airlie <airlied@linux.ie>
As a fallout, replace filp storage with file_priv storage for "unique
identifier of a client" all over the DRM. There is a 1:1 mapping, so this
should be a noop. This could be a minor performance improvement, as everyth
on Linux dereferenced filp to get file_priv anyway, while only the mmap ioct
went the other direction.
Signed-off-by: Dave Airlie <airlied@linux.ie>
This was used to make all ioctl handlers return -errno on linux and errno on
*BSD. Instead, just return -errno in shared code, and flip sign on return f
shared code to *BSD code.
Signed-off-by: Dave Airlie <airlied@linux.ie>
Coverity spotted a "use after free" bug in
drivers/char/agp/amd-k7-agp.c::amd_create_gatt_pages().
The problem is this:
If "entry = kzalloc(sizeof(struct amd_page_map), GFP_KERNEL);"
fails, then there's a loop in the function to free all entries
allocated so far and break out of the allocation loop. That in itself
is pretty sane, but then the (now freed) 'tables' is assigned to
amd_irongate_private.gatt_pages and 'retval' is set to -ENOMEM which
causes amd_free_gatt_pages(); to be called at the end of the function.
The problem with this is that amd_free_gatt_pages() will then loop
'amd_irongate_private.num_tables' times and try to free each entry in
tables[] - this is bad since tables has already been freed and
furthermore it will call kfree(tables) at the end - a double free.
This patch removes the freeing loop in amd_create_gatt_pages() and
instead relies entirely on the call to amd_free_gatt_pages() to free
everything we allocated in case of an error. It also sets
amd_irongate_private.num_tables to the actual number of entries
allocated instead of just using the value passed in from the caller -
this ensures that amd_free_gatt_pages() will only attempt to free
stuff that was actually allocated.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With Andi's clflush fixup, we were getting hangs on server exit, flushing the
mappings after freeing each page helped.
This showed up a race condition where the pages after being freed could be
reused before the agp mappings had been flushed. Flushing after each single
page is a bad thing for future drm work, so make the page destroy a two pass
unmapping all the pages, flushing the mappings, and then destroying the pages.
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Make sure the mmc_spi driver can build without CONFIG_BLOCK.
Issue noted by "Avuton Olrich" <avuton@gmail.com> and randconfig.
While that won't be a common configuration, sometimes embedded
boards use SDIO to interface WLAN or Bluetooth chips (vs some
parallel interface), and don't provide an MMC/SD socket for use
with flash memory cards.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The call to napi_disable() in the PCI shutdown handler is problematic,
and is aggravated by the new NAPI.
Also, make sure watchdog timer doesn't go off.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6: (53 commits)
hwmon: (vt8231) fix sparse warning
hwmon: (sis5595) fix sparse warning
hwmon: (w83627hf) don't assume bank 0
hwmon: (w83627hf) Fix setting fan min right after driver load
hwmon: (w83627hf) De-macro sysfs callback functions
hwmon: Add new combined driver for FSC chips
hwmon: (ibmpex) Release IPMI user if hwmon registration fails
hwmon: (dme1737) Add sch311x support
hwmon: (dme1737) group functions logically
hwmon: (dme1737) cleanups
hwmon: IBM power meter driver
hwmon: (coretemp) Add support for Celeron 4xx
hwmon: (lm87) Disable VID when it should be
hwmon: (w83781d) Add individual alarm and beep files
hwmon: VRM is not read from registers
MAINTAINERS: update hwmon subsystem git trees
hwmon: Fix the code examples in documentation
hwmon: update sysfs interface document - error handling
hwmon: (thmc50) Fix a debug message
hwmon: (thmc50) Don't create temp3 if not enabled
...
- killed paranoid NULL Pointer check
- human readable LED states
- support for "Eicon DIVA USB 4.0" (0x071d/0x1005)
Signed-off-by: Martin Bachem <info@colognechip.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
if your mask is host-endian, you should apply it after le64_to_cpu();
if it's little-endian - before. Doing both (for the same mask and
little-endian value) is broken.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
deal with signedness of the stuff passed to set_bit() et.al.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... since that sucker is not 32bit-only and on 64bit skb->tail is an
offset, not a pointer.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (21 commits)
HID: hidraw_connect() memleak fix
HID: add hidraw interface
USB HID: provide hook for hidraw write()
HID: hiddev: Add 32bit ioctl compatibilty
HID: Add GeneralTouch touchscreen to the blacklist
HID: add support for Microsoft Wireless Laser Keyboard 6000
Input: add KEY_LOGOFF
USBHID: report descriptor fix for MacBook JIS keyboard
HID: trivial fixes in hid-debug
HID: fix input mapping for Microsoft Ergonomic Keyboard
HID: use hid-plff driver for GreenAsia 0e8f:0003 devices
USBHID: Add HID_QUIRK_NOGET for ELO Touch Screen 2700 display
HID: enable hiddev for the SantaRosa MacBookPro IR receiver
USBHID: add CM109 device to blacklist
HID: Report usage codes of keys as EV_MSC scancode events
HID: ignore all non-LED usages in output fields in hid-input
HID: fix whitespace damage
HID: add support for Thrustmaster FGT Force Feedback wheel
HID: minimal autosuspend support for USB HID devices
HID: add support for Microsoft Natural Ergonomic Keyboard 4000
...
* git://git.infradead.org/mtd-2.6:
[MTD] fix mtdconcat for subpage-write NAND
[MTD] [OneNAND] Avoid deadlock in erase callback; release chip lock first.
[MTD] [OneNAND] Return only negative error codes
[MTD] [OneNAND] Synchronize block locking operations
UBI: return correct error code
UBI: remove useless inlines
UBI: fix atomic LEB change problems
UBI: use byte hexdump
UBI: do not use vmalloc on I/O path
UBI: allocate memory with GFP_NOFS
UBI: use linux print_hex_dump(), not home-grown one
UBI: don't use array index before testing if it is negative
UBI: add more prints
UBI: fix sparse warnings
UBI: fix leak in ubi_scan_erase_peb
