The adis16448, unlike the other chips in this family, in addition to the
hardware channels also sends out the DIAG_STAT register in burst mode
before them. Handle that case by skipping over the first 2 bytes before we
pass the received data to the buffer.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: 76ada52f7f ("iio:adis16400: Add support for the adis16448")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There are a few issues with the burst mode support. For one we don't setup
the rx buffer, so the buffer will never be filled and all samples will read
as the zero. Furthermore the tx buffer has the wrong type, which means the
driver sends the wrong command and not the right data is returned.
The final issue is that in burst mode all channels are transferred. Hence
the length of the transfer length should be the number of hardware
channels * 2 bytes. Currently the driver uses indio_dev->scan_bytes for
this. But if the timestamp channel is enabled the scan_bytes will be larger
than the burst length. Fix this by just calculating the burst length based
on the number of hardware channels.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: 5eda3550a3 ("staging:iio:adis16400: Preallocate transfer message")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We unfortunately can't use ~0UL for the scan mask to indicate that the
only valid scan mask is all channels selected. The IIO core needs the exact
mask to work correctly and not a super-set of it. So calculate the masked
based on the channels that are available for a particular device.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: 5eda3550a3 ("staging:iio:adis16400: Preallocate transfer message")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Previously, the two voltage channels had the same ID, which didn't cause
conflicts in sysfs only because one channel is named and the other isn't;
this is still violating the spec though, two indexed channels should never
have the same index.
Signed-off-by: Paul Cercueil <paul.cercueil@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add the scale for the pressure channel, which is currently missing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Fixes: 76ada52f7f ("iio:adis16400: Add support for the adis16448")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We want those fixes (iio primarily) into the -next branch to help with
merge and testing issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch uses iio_trigger_get to increment the reference
count of trigger device, to avoid incorrect assignment.
Can result in a null pointer dereference during removal if the
trigger has been changed before removal.
This patch refers to a similar situation encountered through the
following discussion:
http://www.spinics.net/lists/linux-iio/msg13669.html
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New drivers
* CM3323 color sensor.
* MS5611 pressure and temperature sensor.
New functionality
* mup6050 - create mux clients for devices described via ACPI. The reasoning
and approach taken in this patch are complex. Basically there is no
otherway of finding out what is there than by some esoteric look ups in
the ACPI data.
* cm3232 - PM support
* itg3200 - suspend/resume support
* mcp320x - add more ADCs to the kconfig to reflect what the driver supports
(this patch and the bindings got left behind when the support was added
a while back).
Docs / utils
* ti-adc128s052 - DT bindings.
* mcp3422 - DT bindings.
* mcp320x - DT bindings
* ABI docs for event threshold scale attributes, in_magn_offset, proximity
scan_element and thresh falling/rising values for accelerometers. All
elements long in use that have slipped by being explicitly documented.
* Tidy up the tools previously in drivers/staging/iio/Documentation and move
them out to /tools/iio. Yet another move that should have happened long ago.
This time Roberta Dobrescu did the leg work. Thanks!
Core Cleanups
* Export userspace IIO headers. We should have done the appropriate header
splitting a long time ago. Thanks to Daniel for sorting this out.
* Refactor the registring of attributes for buffers to move all non-custom
ones to a vector allowing easier additions to the current set in the future.
Driver Cleanups
* gpiod related cleanups. Make use of the additional parameter to specify
initial direciton to avoid extra code.
* bmc150 - Various refactorings to reduce code repitition and prepare for
hardware buffer support. Some of these cleanups are good even
without the new functionality.
* kmx61 - direct use of index to an array avoiding a structure element which
was always the index to an element in an array of that structure.
* vf610 - avoid incorrect type for return from wait_for_completion_timeout.
* gp2ap020a00f - use put_unaligned_le32 for slight code simplification.
* ade7754 - improve error handling including suppressing some build warnings.
* ade7759 - improve error handling including suppressing some build warnings.
* hmc5843 - Long line and indentation fixes. Also some constifying of various
constant data.
* ade7854 - 80+ character line splitting.
* ad2s1210 - fix wrong printf format string.
* mxs-lradc - fix wrong printf format string.
* ade7954-i2c - code alignment fixes and other trivial but worthwhile bits.
* periodic rtc trigger - make the frequency type an unsigned int as it
is always treated as such.
* jsa1212 - constify struct regmap_config as it is constant.
* ad7793 - typo in the MODULE_DESCRIPTION
* mma9551 - check gpiod_to_irq errors. Note that this doesn't actually cause
any trouble but is worth tidying up as obviously incorrect.
* mlx90614 - refactor the register symbols to make it clear which reads are to
RAM not PROM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=BmiY
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.1a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new drivers, cleanups and functionality for IIO in the 4.1 cycle.
New drivers
* CM3323 color sensor.
* MS5611 pressure and temperature sensor.
New functionality
* mup6050 - create mux clients for devices described via ACPI. The reasoning
and approach taken in this patch are complex. Basically there is no
otherway of finding out what is there than by some esoteric look ups in
the ACPI data.
* cm3232 - PM support
* itg3200 - suspend/resume support
* mcp320x - add more ADCs to the kconfig to reflect what the driver supports
(this patch and the bindings got left behind when the support was added
a while back).
Docs / utils
* ti-adc128s052 - DT bindings.
* mcp3422 - DT bindings.
* mcp320x - DT bindings
* ABI docs for event threshold scale attributes, in_magn_offset, proximity
scan_element and thresh falling/rising values for accelerometers. All
elements long in use that have slipped by being explicitly documented.
* Tidy up the tools previously in drivers/staging/iio/Documentation and move
them out to /tools/iio. Yet another move that should have happened long ago.
This time Roberta Dobrescu did the leg work. Thanks!
Core Cleanups
* Export userspace IIO headers. We should have done the appropriate header
splitting a long time ago. Thanks to Daniel for sorting this out.
* Refactor the registring of attributes for buffers to move all non-custom
ones to a vector allowing easier additions to the current set in the future.
Driver Cleanups
* gpiod related cleanups. Make use of the additional parameter to specify
initial direciton to avoid extra code.
* bmc150 - Various refactorings to reduce code repitition and prepare for
hardware buffer support. Some of these cleanups are good even
without the new functionality.
* kmx61 - direct use of index to an array avoiding a structure element which
was always the index to an element in an array of that structure.
* vf610 - avoid incorrect type for return from wait_for_completion_timeout.
* gp2ap020a00f - use put_unaligned_le32 for slight code simplification.
* ade7754 - improve error handling including suppressing some build warnings.
* ade7759 - improve error handling including suppressing some build warnings.
* hmc5843 - Long line and indentation fixes. Also some constifying of various
constant data.
* ade7854 - 80+ character line splitting.
* ad2s1210 - fix wrong printf format string.
* mxs-lradc - fix wrong printf format string.
* ade7954-i2c - code alignment fixes and other trivial but worthwhile bits.
* periodic rtc trigger - make the frequency type an unsigned int as it
is always treated as such.
* jsa1212 - constify struct regmap_config as it is constant.
* ad7793 - typo in the MODULE_DESCRIPTION
* mma9551 - check gpiod_to_irq errors. Note that this doesn't actually cause
any trouble but is worth tidying up as obviously incorrect.
* mlx90614 - refactor the register symbols to make it clear which reads are to
RAM not PROM.
Fix inconsistency in the semantics of the scale attribute.
For scale the write_raw function was considering the scale table index
and writing the appropriate value into the range register, while
for read_raw it was outputting the actual scale.
Fix this behaviour and adhere to the iio ABI specification.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Reviewed-by: Viorel Suman <viorel.suman@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A hardware fifo reset always imply an invalidation of the
existing timestamps, so we'll clear timestamps fifo on
successfull hardware fifo reset.
Signed-off-by: Viorel Suman <viorel.suman@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If the in-kernel push interface is used we may have a different masks
on the device buffer and the kernel buffer and in this case the device
should generate data for the reunion of the buffers, which is
available at indio_dev->active_scan_mask.
Compiled tested only except for bmc150-accel which was tested at
runtime with the hardware.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
set dependent on patches in the recent merge windows will follow shortly.
* dht11 - fix a read off the end of an array, add some locking to prevent
the read function being interrupted and make sure gpio/irq lines
are not enabled for irqs during output.
* iadc - timeout should be in jiffies not msecs
* mpu6050 - avoid a null id from ACPI emumeration being dereferenced.
* mxs-lradc - fix up some interaction issues between the touchscreen driver
and iio driver. Mostly about making sure that the adc driver
only affects channels that are not being used for the
touchscreen.
* ad2s1200 - sign extension fix for a result of c type promotion.
* adis16400 - sign extension fix for a result of c type promotion.
* mcp3422 - scale table was transposed.
* ad5686 - use _optional regulator get to avoid a dummy reg being allocate
which would cause the driver to fail to initialize.
* gp2ap020a00f - select REGMAP_I2C
* si7020 - revert an incorrect cleanup up and then fix the issue that made
that cleanup seem like a good idea.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=iNyv
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.0a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of fixes for IIO in the 4.0 cycle. Note a followup
set dependent on patches in the recent merge windows will follow shortly.
* dht11 - fix a read off the end of an array, add some locking to prevent
the read function being interrupted and make sure gpio/irq lines
are not enabled for irqs during output.
* iadc - timeout should be in jiffies not msecs
* mpu6050 - avoid a null id from ACPI emumeration being dereferenced.
* mxs-lradc - fix up some interaction issues between the touchscreen driver
and iio driver. Mostly about making sure that the adc driver
only affects channels that are not being used for the
touchscreen.
* ad2s1200 - sign extension fix for a result of c type promotion.
* adis16400 - sign extension fix for a result of c type promotion.
* mcp3422 - scale table was transposed.
* ad5686 - use _optional regulator get to avoid a dummy reg being allocate
which would cause the driver to fail to initialize.
* gp2ap020a00f - select REGMAP_I2C
* si7020 - revert an incorrect cleanup up and then fix the issue that made
that cleanup seem like a good idea.
This is a follow up patches after adding i2c mux adapter for bypass
mode. Potentially many different types of sensor can be attached to
INVMPU6XXX device, which can be connected to main cpu i2c bus in
bypass mode.
Why do we need this?
The system ACPI table entry will consist of only one device for
INV6XXX, assuming that this driver will handle all connected sensors.
That is not true for the Linux driver. There are bunch of IIO drivers
for each sensors, hence we created a mux on this device. So to load
these additional drivers, we need to create i2c devices for them
in this driver using this mux adapter.
There are multiple options:
1. Use the auto detect feature, this needs a new i2c class for the
adapter as the existing HWMON class is not acceptable. Also the
autodetect has overhead of executing detect method for each
matching class of adapters.
This is a simple implementation. This option was previously submitted
with not a happy feedback.
2. Option is use ACPI magic and parse the configuration data. What
we need to create a i2c device at a minimum is address and a name.
Address can be obtained for secondary device in more or less in a
standard way from using _CRS element. But there is no name. To get
name we need to process proprietary vendor data. Not having name is
not fun, as you have to create device using the device name of
INVN6XXXX, respecting driver duplicate name space restriction.
Also each client driver needs to have this name in the id table.
Since multiple driver can be loaded, the driver should be able to
detect its presence and gracefully exit for the other client driver
to take it over.
So we use two step process:
- Use DMI to id platform and parse propritery data. This is not uncommon
for many x86 platform specific driver. We will get both name and address.
The change created necessary infrastructure to add more properitery vendor
data parsing.
- If DMI match fails, then create device on INV6XXX-client (we can't
create with same name as INV6XXX as it will cause duplicate name and driver
model will reject.) With this each client sensor driver which needs to get
attached via INV6XXXX, need this name in the id table and detect the
physical presence of sensor in probe and exit if not found.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for
outputs.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
odr_bits values are between 0 and 11, so we can use the index
in kmx61_samp_freq_table instead of odr_bits structure member.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The intention is obviously to sign-extend a 12 bit quantity. But
because of C's promotion rules, the assignment is equivalent to "val16
&= 0xfff;". Use the proper API for this.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/iio/imu/kmx61.c
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When id is null, with ACPI enumeration, don't dereference it.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We have two IIO devices and we need to adjust the base
when reading data.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Useful in the debugging phase, not needed now.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes parts of kmx61 error handling to make code easier to read and to be
more consistent with IIO coding conventions:
* prefer as single point for error handling instead of duplicating code
for each function
* directly return a value from a case branch instead of breaking
* fix error message for writing REG_CTRL1
Also, add separate error paths for kmx61_trigger_setup/iio_triggered_buffer_setup
calls.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
..except while in an error handler, where there is nothing
to be done anyway.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added changes so that the module can be enumerated via ACPI.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
drivers/iio/imu/kmx61.c:422:5: sparse: symbol 'kmx61_set_wake_up_odr' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We use WUFE (Wake Up from Sleep Engine) and BTSE (Back to Sleep Engine)
to detect general motion input.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This creates a data ready trigger per IIO device.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Per sensor state (ACTIVE/STANDBY) is saved in driver's
private data (acc_stby/mag_stby) and restored when
resume is called.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
By default both sensors are ACTIVE, in this way the driver
will work even if CONFIG_PM_RUNTIME is not selected.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Minimal implementation for KMX61 6-axis accelerometer/magnetometer. It exports
raw accel/magn readings together with scale and sampling frequency.
This driver uses two IIO devices one for accelerometer and one for magnetometer.
Datasheet will be available at:
http://www.kionix.com/6-axis-accelerometer-magnetometer/kmx61
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The two halves of this part can run largely independently. Hence
a version 4 of this patch followed that reorganized things completely.
This reverts commit d7d787d291.
This chip allows some limited number of sensors connected to it as
slaves, which can be directly accessed by register interface of this
driver.But the current upstream driver doesn't support such mode.
To attach such slaves to main processor i2c bus, chip has to be set
up in bypass mode. This change adds i2c mux, which will enable/disable
this mode for transaction to/from such slave devices.
This was discussed for a while in mailing list, this was the outcome:
Reference:
http://www.spinics.net/lists/linux-iio/msg12126.htmlhttp://comments.gmane.org/gmane.linux.kernel.iio/11470
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Minimal implementation for KMX61 6-axis accelerometer/magnetometer. It exports
raw accel/magn readings together with scale and sampling frequency.
Datasheet will be available at:
http://www.kionix.com/6-axis-accelerometer-magnetometer/kmx61
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We want the fixes in there, and it resolves a merge issue with
drivers/iio/accel/bma180.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Casting the return value which is a void pointer is redundant.
The conversion from void pointer to any other pointer type is
guaranteed by the C programming language.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This can result in wrong reference count for trigger device, call
iio_trigger_get to increment reference.
Refer to http://www.spinics.net/lists/linux-iio/msg13669.html for discussion
with Jonathan.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
By using the info_mask_shared_by_all element of the channel spec, access
to the sampling frequency becomes available to in kernel users of the
driver. It also shortens and simplifies the code.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
By using the info_mask_shared_by_all element of the channel spec, access
to the sampling frequency becomes available to in kernel users of the
driver. It also shortens and simplifies the code.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
'rx' is not used in this function. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This resolves the conflicts in the files:
drivers/iio/adc/Kconfig
drivers/staging/rtl8723au/os_dep/usb_ops_linux.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver segfaults when the kernel boots with device tree as the
platform data is then not present and the pointer is deferenced without
checking it is not null. This patch introduces such a check avoiding the
crash.
Signed-off-by: Atilla Filiz <atilla.filiz@essensium.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: Stable@vger.kernel.org
Adding MPU6500 in target list for this driver.
Description:
Source
Document: MPU-6500 Register Map and Descriptions Revision 2.1
Section 3: Register Map
This section describes difference in terms device programmability
between MPU6050 and MPU6500.
These are different registers, which differs between MPU6050 and
MPU6500.
Addr Name
---------------------
1E LP_ACCEL_ODR
6C PWR_MGMT_2
77 XA_OFFSET_H
78 XA_OFFSET_L
7A YA_OFFSET_H
7B YA_OFFSET_L
7D ZA_OFFSET_H
7E ZA_OFFSET_L
But the current MPU6050 driver doesn't use registers which are different
except PWR_MGMT_2. The difference is support of "LP_WAKE_CTRL" at bit6-7
in MPU6050 mode. In MPU6500 they are not defined.
In current mpu6050 driver, only values used for this register are for
standby mode for gyro and accelerometer.
In both case frequency of wakeups is set to default and not using
bit 6-7.
So this driver van as well support MPU6500. In addition MPU6500 can
run MPU6050 mode by changing device trim settings.
So changing config comments to allow MPU6500 to use this driver.
When the driver is enhanced to support more functions, i2c driver
data INV_MPU6500 or "WHO_AM_I" register can be used to add additional
functionality.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
