Make the FRV arch use the generic IRQ code rather than having its own
routines for doing so.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace ctxid with sid in selinux_audit_rule_match interface for
consistency with other interfaces.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename selinux_ctxid_to_string to selinux_sid_to_string to be
consistent with other interfaces.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Eliminate selinux_task_ctxid since it duplicates selinux_task_get_sid.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are many places where we need to determine the node of a zone.
Currently we use a difficult to read sequence of pointer dereferencing.
Put that into an inline function and use throughout VM. Maybe we can find
a way to optimize the lookup in the future.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently one can enable slab reclaim by setting an explicit option in
/proc/sys/vm/zone_reclaim_mode. Slab reclaim is then used as a final
option if the freeing of unmapped file backed pages is not enough to free
enough pages to allow a local allocation.
However, that means that the slab can grow excessively and that most memory
of a node may be used by slabs. We have had a case where a machine with
46GB of memory was using 40-42GB for slab. Zone reclaim was effective in
dealing with pagecache pages. However, slab reclaim was only done during
global reclaim (which is a bit rare on NUMA systems).
This patch implements slab reclaim during zone reclaim. Zone reclaim
occurs if there is a danger of an off node allocation. At that point we
1. Shrink the per node page cache if the number of pagecache
pages is more than min_unmapped_ratio percent of pages in a zone.
2. Shrink the slab cache if the number of the nodes reclaimable slab pages
(patch depends on earlier one that implements that counter)
are more than min_slab_ratio (a new /proc/sys/vm tunable).
The shrinking of the slab cache is a bit problematic since it is not node
specific. So we simply calculate what point in the slab we want to reach
(current per node slab use minus the number of pages that neeed to be
allocated) and then repeately run the global reclaim until that is
unsuccessful or we have reached the limit. I hope we will have zone based
slab reclaim at some point which will make that easier.
The default for the min_slab_ratio is 5%
Also remove the slab option from /proc/sys/vm/zone_reclaim_mode.
[akpm@osdl.org: cleanups]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the atomic counter for slab_reclaim_pages and replace the counter
and NR_SLAB with two ZVC counter that account for unreclaimable and
reclaimable slab pages: NR_SLAB_RECLAIMABLE and NR_SLAB_UNRECLAIMABLE.
Change the check in vmscan.c to refer to to NR_SLAB_RECLAIMABLE. The
intend seems to be to check for slab pages that could be freed.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
*_pages is a better description of the role of the variable.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One of the changes necessary for shared page tables is to standardize the
pxx_page macros. pte_page and pmd_page have always returned the struct
page associated with their entry, while pte_page_kernel and pmd_page_kernel
have returned the kernel virtual address. pud_page and pgd_page, on the
other hand, return the kernel virtual address.
Shared page tables needs pud_page and pgd_page to return the actual page
structures. There are very few actual users of these functions, so it is
simple to standardize their usage.
Since this is basic cleanup, I am submitting these changes as a standalone
patch. Per Hugh Dickins' comments about it, I am also changing the
pxx_page_kernel macros to pxx_page_vaddr to clarify their meaning.
Signed-off-by: Dave McCracken <dmccr@us.ibm.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In many places we will need to use the same combination of flags. Specify
a single GFP_THISNODE definition for ease of use in gfp.h.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new gfp flag __GFP_THISNODE to avoid fallback to other nodes. This
flag is essential if a kernel component requires memory to be located on a
certain node. It will be needed for alloc_pages_node() to force allocation
on the indicated node and for alloc_pages() to force allocation on the
current node.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Let's try to keep mm/ comments more useful and up to date. This is a start.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce ARCH_LOW_ADDRESS_LIMIT which can be set per architecture to
override the 4GB default limit used by the bootmem allocater within
__alloc_bootmem_low() and __alloc_bootmem_low_node(). E.g. s390 needs a
2GB limit instead of 4GB.
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
lock_page needs the caller to have a reference on the page->mapping inode
due to sync_page, ergo set_page_dirty_lock is obviously buggy according to
its comments.
Solve it by introducing a new lock_page_nosync which does not do a sync_page.
akpm: unpleasant solution to an unpleasant problem. If it goes wrong it could
cause great slowdowns while the lock_page() caller waits for kblockd to
perform the unplug. And if a filesystem has special sync_page() requirements
(none presently do), permanent hangs are possible.
otoh, set_page_dirty_lock() is usually (always?) called against userspace
pages. They are always up-to-date, so there shouldn't be any pending read I/O
against these pages.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch splits alloc_percpu() up into two phases. Likewise for
free_percpu(). This allows clients to limit initial allocations to online
cpu's, and to populate or depopulate per-cpu data at run time as needed:
struct my_struct *obj;
/* initial allocation for online cpu's */
obj = percpu_alloc(sizeof(struct my_struct), GFP_KERNEL);
...
/* populate per-cpu data for cpu coming online */
ptr = percpu_populate(obj, sizeof(struct my_struct), GFP_KERNEL, cpu);
...
/* access per-cpu object */
ptr = percpu_ptr(obj, smp_processor_id());
...
/* depopulate per-cpu data for cpu going offline */
percpu_depopulate(obj, cpu);
...
/* final removal */
percpu_free(obj);
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a notifer chain to the out of memory killer. If one of the registered
callbacks could release some memory, do not kill the process but return and
retry the allocation that forced the oom killer to run.
The purpose of the notifier is to add a safety net in the presence of
memory ballooners. If the resource manager inflated the balloon to a size
where memory allocations can not be satisfied anymore, it is better to
deflate the balloon a bit instead of killing processes.
The implementation for the s390 ballooner is included.
[akpm@osdl.org: cleanups]
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I wonder why we need this bitmask indexing into zone->node_zonelists[]?
We always start with the highest zone and then include all lower zones
if we build zonelists.
Are there really cases where we need allocation from ZONE_DMA or
ZONE_HIGHMEM but not ZONE_NORMAL? It seems that the current implementation
of highest_zone() makes that already impossible.
If we go linear on the index then gfp_zone() == highest_zone() and a lot
of definitions fall by the wayside.
We can now revert back to the use of gfp_zone() in mempolicy.c ;-)
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
After we have done this we can now do some typing cleanup.
The memory policy layer keeps a policy_zone that specifies
the zone that gets memory policies applied. This variable
can now be of type enum zone_type.
The check_highest_zone function and the build_zonelists funnctionm must
then also take a enum zone_type parameter.
Plus there are a number of loops over zones that also should use
zone_type.
We run into some troubles at some points with functions that need a
zone_type variable to become -1. Fix that up.
[pj@sgi.com: fix set_mempolicy() crash]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a check in zonelist_policy that compares pieces of the bitmap
obtained from a gfp mask via GFP_ZONETYPES with a zone number in function
zonelist_policy().
The bitmap is an ORed mask of __GFP_DMA, __GFP_DMA32 and __GFP_HIGHMEM.
The policy_zone is a zone number with the possible values of ZONE_DMA,
ZONE_DMA32, ZONE_HIGHMEM and ZONE_NORMAL. These are two different domains
of values.
For some reason seemed to work before the zone reduction patchset (It
definitely works on SGI boxes since we just have one zone and the check
cannot fail).
With the zone reduction patchset this check definitely fails on systems
with two zones if the system actually has memory in both zones.
This is because ZONE_NORMAL is selected using no __GFP flag at
all and thus gfp_zone(gfpmask) == 0. ZONE_DMA is selected when __GFP_DMA
is set. __GFP_DMA is 0x01. So gfp_zone(gfpmask) == 1.
policy_zone is set to ZONE_NORMAL (==1) if ZONE_NORMAL and ZONE_DMA are
populated.
For ZONE_NORMAL gfp_zone(<no _GFP_DMA>) yields 0 which is <
policy_zone(ZONE_NORMAL) and so policy is not applied to regular memory
allocations!
Instead gfp_zone(__GFP_DMA) == 1 which results in policy being applied
to DMA allocations!
What we realy want in that place is to establish the highest allowable
zone for a given gfp_mask. If the highest zone is higher or equal to the
policy_zone then memory policies need to be applied. We have such
a highest_zone() function in page_alloc.c.
So move the highest_zone() function from mm/page_alloc.c into
include/linux/gfp.h. On the way we simplify the function and use the new
zone_type that was also introduced with the zone reduction patchset plus we
also specify the right type for the gfp flags parameter.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
eventcounters: Do not display counters for zones that are not available on an
arch
Do not define or display counters for the DMA32 and the HIGHMEM zone if such
zones were not configured.
[akpm@osdl.org: s390 fix]
[heiko.carstens@de.ibm.com: s390 fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make ZONE_HIGHMEM optional
- ifdef out code and definitions related to CONFIG_HIGHMEM
- __GFP_HIGHMEM falls back to normal allocations if there is no
ZONE_HIGHMEM
- GFP_ZONEMASK becomes 0x01 if there is no DMA32 and no HIGHMEM
zone.
[jdike@addtoit.com: build fix]
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make ZONE_DMA32 optional
- Add #ifdefs around ZONE_DMA32 specific code and definitions.
- Add CONFIG_ZONE_DMA32 config option and use that for x86_64
that alone needs this zone.
- Remove the use of CONFIG_DMA_IS_DMA32 and CONFIG_DMA_IS_NORMAL
for ia64 and fix up the way per node ZVCs are calculated.
- Fall back to prior GFP_ZONEMASK of 0x03 if there is no
DMA32 zone.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use enum for zones and reformat zones dependent information
Add comments explaning the use of zones and add a zones_t type for zone
numbers.
Line up information that will be #ifdefd by the following patches.
[akpm@osdl.org: comment cleanups]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move totalhigh_pages and nr_free_highpages() into highmem.c/.h
Move the totalhigh_pages definition into highmem.c/.h. Move the
nr_free_highpages function into highmem.c
[yoichi_yuasa@tripeaks.co.jp: build fix]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It fixes various coding style issues, specially when spaces are useless. For
example '*' go next to the function name.
Signed-off-by: Franck Bui-Huu <vagabon.xyz@gmail.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__init in headers is pretty useless because the compiler doesn't check it, and
they get out of sync relatively frequently. So if you see an __init in a
header file, it's quite unreliable and you need to check the definition
anyway.
Signed-off-by: Franck Bui-Huu <vagabon.xyz@gmail.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Address a long standing issue of booting with an initrd on an i386 numa
system. Currently (and always) the numa kva area is mapped into low memory
by finding the end of low memory and moving that mark down (thus creating
space for the kva). The issue with this is that Grub loads initrds into
this similar space so when the kernel check the initrd it finds it outside
max_low_pfn and disables it (it thinks the initrd is not mapped into usable
memory) thus initrd enabled kernels can't boot i386 numa :(
My solution to the problem just converts the numa kva area to use the
bootmem allocator to save it's area (instead of moving the end of low
memory). Using bootmem allows the kva area to be mapped into more diverse
addresses (not just the end of low memory) and enables the kva area to be
mapped below the initrd if present.
I have tested this patch on numaq(no initrd) and summit(initrd) i386 numa
based systems.
[akpm@osdl.org: cleanups]
Signed-off-by: Keith Mannthey <kmannth@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes the following needlessly global functions static:
- slab.c: kmem_find_general_cachep()
- swap.c: __page_cache_release()
- vmalloc.c: __vmalloc_node()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that we can detect writers of shared mappings, throttle them. Avoids OOM
by surprise.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tracking of dirty pages in shared writeable mmap()s.
The idea is simple: write protect clean shared writeable pages, catch the
write-fault, make writeable and set dirty. On page write-back clean all the
PTE dirty bits and write protect them once again.
The implementation is a tad harder, mainly because the default
backing_dev_info capabilities were too loosely maintained. Hence it is not
enough to test the backing_dev_info for cap_account_dirty.
The current heuristic is as follows, a VMA is eligible when:
- its shared writeable
(vm_flags & (VM_WRITE|VM_SHARED)) == (VM_WRITE|VM_SHARED)
- it is not a 'special' mapping
(vm_flags & (VM_PFNMAP|VM_INSERTPAGE)) == 0
- the backing_dev_info is cap_account_dirty
mapping_cap_account_dirty(vma->vm_file->f_mapping)
- f_op->mmap() didn't change the default page protection
Page from remap_pfn_range() are explicitly excluded because their COW
semantics are already horrid enough (see vm_normal_page() in do_wp_page()) and
because they don't have a backing store anyway.
mprotect() is taught about the new behaviour as well. However it overrides
the last condition.
Cleaning the pages on write-back is done with page_mkclean() a new rmap call.
It can be called on any page, but is currently only implemented for mapped
pages, if the page is found the be of a VMA that accounts dirty pages it will
also wrprotect the PTE.
Finally, in fs/buffers.c:try_to_free_buffers(); remove clear_page_dirty() from
under ->private_lock. This seems to be safe, since ->private_lock is used to
serialize access to the buffers, not the page itself. This is needed because
clear_page_dirty() will call into page_mkclean() and would thereby violate
locking order.
[dhowells@redhat.com: Provide a page_mkclean() implementation for NOMMU]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce a VM_BUG_ON, which is turned on with CONFIG_DEBUG_VM. Use this
in the lightweight, inline refcounting functions; PageLRU and PageActive
checks in vmscan, because they're pretty well confined to vmscan. And in
page allocate/free fastpaths which can be the hottest parts of the kernel
for kbuilds.
Unlike BUG_ON, VM_BUG_ON must not be used to execute statements with
side-effects, and should not be used outside core mm code.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Give non-highmem architectures access to the kmap API for the purposes of
overriding (this is what the attached patch does).
The proposal is that we should now require all architectures with coherence
issues to manage data coherence via the kmap/kunmap API. Thus driver
writers never have to write code like
kmap(page)
modify data in page
flush_kernel_dcache_page(page)
kunmap(page)
instead, kmap/kunmap will manage the coherence and driver (and filesystem)
writers don't need to worry about how to flush between kmap and kunmap.
For most architectures, the page only needs to be flushed if it was
actually written to *and* there are user mappings of it, so the best
implementation looks to be: clear the page dirty pte bit in the kernel page
tables on kmap and on kunmap, check page->mappings for user maps, and then
the dirty bit, and only flush if it both has user mappings and is dirty.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
get_cpu_var()/per_cpu()/__get_cpu_var() arguments must be simple
identifiers. Otherwise the arch dependent implementations might break.
This patch enforces the correct usage of the macros by producing a syntax
error if the variable is not a simple identifier.
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The counter is exported to /sys that keeps track of the
number of thermal events, such that the user knows how bad the
thermal problem might be (since the logging to syslog and mcelog
is rate limited).
AK: Fixed cpu hotplug locking
Signed-off-by: Dmitriy Zavin <dmitriyz@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Refactor the event processing (syslog messaging and rate limiting)
into separate file therm_throt.c. This allows consistent reporting
of CPU thermal throttle events.
After ACK'ing the interrupt, if the event is current, the user
(p4.c/mce_intel.c) calls therm_throt_process to log (and rate limit)
the event. If that function returns 1, the user has the option to log
things further (such as to mce_log in x86_64).
AK: minor cleanup
Signed-off-by: Dmitriy Zavin <dmitriyz@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The current time_before/time_after macros will fail typechecks
when passed u64 values (as returned by get_jiffies_64()). On 64bit
systems, this will just result in a warning about mismatching types
without explicit casts, but since unsigned long and u64
(unsigned long long) are of same size, it will still work.
On 32bit systems, a long is 32bits, so the value from get_jiffies_64()
will be truncated by the cast and thus lose all the precision gained by
64bit jiffies.
Signed-off-by: Dmitriy Zavin <dmitriyz@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Fix
linux/arch/x86_64/kernel/traps.c: In function 'dump_trace':
linux/arch/x86_64/kernel/traps.c:275: warning: cast to pointer from integer of different size
with allnoconfig
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Some buggy systems can machine check when config space accesses
happen for some non existent devices. i386/x86-64 do some early
device scans that might trigger this. Allow pci=noearly to disable
this. Also when type 1 is disabling also don't do any early
accesses which are always type1.
This moves the pci= configuration parsing to be a early parameter.
I don't think this can break anything because it only changes
a single global that is only used by PCI.
Cc: gregkh@suse.de
Cc: Trammell Hudson <hudson@osresearch.net>
Signed-off-by: Andi Kleen <ak@suse.de>
SYSENTER can cause a NT to be set which might cause crashes on the IRET
in the next task.
Following similar i386 patch from Linus.
Signed-off-by: Andi Kleen <ak@suse.de>
Current gcc generates calls not jumps to noreturn functions. When that happens the
return address can point to the next function, which confuses the unwinder.
This patch works around it by marking asynchronous exception
frames in contrast normal call frames in the unwind information. Then teach
the unwinder to decode this.
For normal call frames the unwinder now subtracts one from the address which avoids
this problem. The standard libgcc unwinder uses the same trick.
It doesn't include adjustment of the printed address (i.e. for the original
example, it'd still be kernel_math_error+0 that gets displayed, but the
unwinder wouldn't get confused anymore.
This only works with binutils 2.6.17+ and some versions of H.J.Lu's 2.6.16
unfortunately because earlier binutils don't support .cfi_signal_frame
[AK: added automatic detection of the new binutils and wrote description]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Fix pack_descriptor:
1. flags are bits 20-23 in the high word
2. limit's 4 msb are bits 16-19 in the high word
These haven't mattered so far, because all users have had small limits
and a flags setting of 0.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
===================================================================
Previously exit_idle would be called more often than enter_idle
Now instead of using complicated tests just keep track of it
using the per CPU variable as a flip flop. I moved the idle state into the
PDA to make the access more efficient.
Original bug report and an initial patch from Stephane Eranian,
but redone by AK.
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Reindent the macros in x86-64 pda.h, making them much more readable.
Follows Jeremy's i386 version of this.
No functional changes
Signed-off-by: Andi Kleen <ak@suse.de>
- Don't zero for __copy_from_user_inatomic following i386.
This will prevent spurious zeros for parallel file system writers when
one does a exception
- The string instruction version didn't zero the output on
exception. Oops.
Also I cleaned up the code a bit while I was at it and added a minor
optimization to the string instruction path.
Signed-off-by: Andi Kleen <ak@suse.de>
We allow for the fact that the guest kernel may not run in ring 0. This
requires some abstraction in a few places when setting %cs or checking
privilege level (user vs kernel).
This is Chris' [RFC PATCH 15/33] move segment checks to subarch, except rather
than using #define USER_MODE_MASK which depends on a config option, we use
Zach's more flexible approach of assuming ring 3 == userspace. I also used
"get_kernel_rpl()" over "get_kernel_cs()" because I think it reads better in
the code...
1) Remove the hardcoded 3 and introduce #define SEGMENT_RPL_MASK 3 2) Add a
get_kernel_rpl() macro, and don't assume it's zero.
And:
Clean up of patch for letting kernel run other than ring 0:
a. Add some comments about the SEGMENT_IS_*_CODE() macros.
b. Add a USER_RPL macro. (Code was comparing a value to a mask
in some places and to the magic number 3 in other places.)
c. Add macros for table indicator field and use them.
d. Change the entry.S tests for LDT stack segment to use the macros
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Abstract sensitive instructions in assembler code, replacing them with macros
(which currently are #defined to the native versions). We use long names:
assembler is case-insensitive, so if something goes wrong and macros do not
expand, it would assemble anyway.
Resulting object files are exactly the same as before.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
I just added type checking for assignments the PDA in the i386 PDA code.
Here's the x86-64 equivalent. (Obviously this doesn't contain the latest
x86-64 PDA change.)
Signed-off-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch adds the per thread cookie field to the task struct and the PDA.
Also it makes sure that the PDA value gets the new cookie value at context
switch, and that a new task gets a new cookie at task creation time.
Signed-off-by: Arjan van Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
CC: Andi Kleen <ak@suse.de>
Change the comments in the pda structure to make the first fields to have
their offset documented and to have the comments aligned.
The stack protector series needs a field at offset 40 (gcc ABI); annotate
upto 40 for that reason.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
CC: Andi Kleen <ak@suse.de>
kexec: Avoid overwriting the current pgd (V4, i386)
This patch upgrades the i386-specific kexec code to avoid overwriting the
current pgd. Overwriting the current pgd is bad when CONFIG_CRASH_DUMP is used
to start a secondary kernel that dumps the memory of the previous kernel.
The code introduces a new set of page tables. These tables are used to provide
an executable identity mapping without overwriting the current pgd.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
kexec: Avoid overwriting the current pgd (V4, x86_64)
This patch upgrades the x86_64-specific kexec code to avoid overwriting the
current pgd. Overwriting the current pgd is bad when CONFIG_CRASH_DUMP is used
to start a secondary kernel that dumps the memory of the previous kernel.
The code introduces a new set of page tables. These tables are used to provide
an executable identity mapping without overwriting the current pgd.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Signed-off-by: Andi Kleen <ak@suse.de>
Remove most of the special cases for the debug IST stack. This is a
follow on clean up patch, it requires the bug fix patch that adds
orig_ist.
Signed-off-by: Keith Owens <kaos@ocs.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
The EDD code would scan the command line as a fixed array, without
taking account of either whitespace, null-termination, the old
command-line protocol, late overrides early, or the fact that the
command line may not be reachable from INITSEG.
This should fix those problems, and enable us to use a longer command
line.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Based on a idea by Jeremy Fitzhardinge:
Replace the volatiles and memory clobbers in the PDA access with
telling gcc about access to a proxy PDA structure that doesn't
actually exist. But the dummy accesses give a defined ordering for
read/write accesses.
Also add some memory barriers to the early GS initialization to
make sure no PDA access is moved before it.
Advantage is some .text savings (probably most from better
code for accessing "current"):
text data bss dec hex filename
4845647 1223688 615864 6685199 66020f vmlinux
4837780 1223688 615864 6677332 65e354 vmlinux-pda
1.2% smaller code
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Based on patch from David Rientjes <rientjes@google.com>, but
changed by AK.
Optimizes the 64-bit hamming weight for x86_64 processors assuming they
have fast multiplication. Uses five fewer bitops than the generic
hweight64. Benchmark on one EMT64 showed ~25% speedup with 2^24
consecutive calls.
Define a new ARCH_HAS_FAST_MULTIPLIER that can be set by other
architectures that can also multiply fast.
Signed-off-by: Andi Kleen <ak@suse.de>
Drop support for non e820 BIOS calls to get the memory map.
The boot assembler code still has some support, but not the C code now.
Signed-off-by: Andi Kleen <ak@suse.de>
- Remove a define that was used only once
- Remove the too large APIC ID check because we always support
the full 8bit range of APICs.
- Restructure code a bit to be simpler.
Cc: len.brown@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Fix the pte_exec/mkexec page table accessor functions to really
use the NX bit. Previously they only checked the USER bit, but
weren't actually used for anything.
Then use them in change_page_attr() to manipulate the NX bit
properly.
Signed-off-by: Andi Kleen <ak@suse.de>
And replace all users with ordinary smp_processor_id. The function
was originally added to get some basic oops information out even
if the GS register was corrupted. However that didn't
work for some anymore because printk is needed to print the oops
and it uses smp_processor_id() already. Also GS register corruptions
are not particularly common anymore.
This also helps the Xen port which would otherwise need to
do this in a special way because it can't access the local APIC.
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Andi Kleen <ak@suse.de>
In i386's entry.S, FIX_STACK() needs annotation because it
replaces the stack pointer. And the rest of nmi() needs
annotation in order to compile with these new annotations.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Apparently IA64 needs it, but i386/x86-64 don't anymore
since gcc 2.95 support was dropped. Nobody else on linux-arch
requested keeping it generically
Cc: tony.luck@intel.com
Cc: kaos@sgi.com
Signed-off-by: Andi Kleen <ak@suse.de>
Right now the kernel on x86-64 has a 100% lazy fpu behavior: after *every*
context switch a trap is taken for the first FPU use to restore the FPU
context lazily. This is of course great for applications that have very
sporadic or no FPU use (since then you avoid doing the expensive
save/restore all the time). However for very frequent FPU users... you
take an extra trap every context switch.
The patch below adds a simple heuristic to this code: After 5 consecutive
context switches of FPU use, the lazy behavior is disabled and the context
gets restored every context switch. If the app indeed uses the FPU, the
trap is avoided. (the chance of the 6th time slice using FPU after the
previous 5 having done so are quite high obviously).
After 256 switches, this is reset and lazy behavior is returned (until
there are 5 consecutive ones again). The reason for this is to give apps
that do longer bursts of FPU use still the lazy behavior back after some
time.
[akpm@osdl.org: place new task_struct field next to jit_keyring to save space]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch enables ACPI based physical CPU hotplug support for x86_64.
Implements acpi_map_lsapic() and acpi_unmap_lsapic() to support physical cpu
hotplug.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Now for a completely different but trivial approach.
I just boot tested it with 255 CPUS and everything worked.
Currently everything (except module data) we place in
the per cpu area we know about at compile time. So
instead of allocating a fixed size for the per_cpu area
allocate the number of bytes we need plus a fixed constant
for to be used for modules.
It isn't perfect but it is much less of a pain to
work with than what we are doing now.
AK: fixed warning
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The implementation comes from Zach's [RFC, PATCH 10/24] i386 Vmi
descriptor changes:
Descriptor and trap table cleanups. Add cleanly written accessors for
IDT and GDT gates so the subarch may override them. Note that this
allows the hypervisor to transparently tweak the DPL of the descriptors
as well as the RPL of segments in those descriptors, with no unnecessary
kernel code modification. It also allows the hypervisor implementation
of the VMI to tweak the gates, allowing for custom exception frames or
extra layers of indirection above the guest fault / IRQ handlers.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch moves the entry.S:error_entry to .kprobes.text section,
since code marked unsafe for kprobes jumps directly to entry.S::error_entry,
that must be marked unsafe as well.
This patch also moves all the ".previous.text" asm directives to ".previous"
for kprobes section.
AK: Following a similar i386 patch from Chuck Ebbert
AK: Also merged Jeremy's fix in.
+From: Jeremy Fitzhardinge <jeremy@goop.org>
KPROBE_ENTRY does a .section .kprobes.text, and expects its users to
do a .previous at the end of the function.
Unfortunately, if any code within the function switches sections, for
example .fixup, then the .previous ends up putting all subsequent code
into .fixup. Worse, any subsequent .fixup code gets intermingled with
the code its supposed to be fixing (which is also in .fixup). It's
surprising this didn't cause more havok.
The fix is to use .pushsection/.popsection, so this stuff nests
properly. A further cleanup would be to get rid of all
.section/.previous pairs, since they're inherently fragile.
+From: Chuck Ebbert <76306.1226@compuserve.com>
Because code marked unsafe for kprobes jumps directly to
entry.S::error_code, that must be marked unsafe as well.
The easiest way to do that is to move the page fault entry
point to just before error_code and let it inherit the same
section.
Also moved all the ".previous" asm directives for kprobes
sections to column 1 and removed ".text" from them.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Following x86-64 patches. Reuses code from them in fact.
Convert the standard backtracer to do all output using
callbacks. Use the x86-64 stack tracer implementation
that uses these callbacks to implement the stacktrace interface.
This allows to use the new dwarf2 unwinder for stacktrace
and get better backtraces.
Cc: mingo@elte.hu
Signed-off-by: Andi Kleen <ak@suse.de>
This unifies the standard backtracer and the new stacktrace
in memory backtracer. The standard one is converted to use callbacks
and then reimplement stacktrace using new callbacks.
The main advantage is that stacktrace can now use the new dwarf2 unwinder
and avoid false positives in many cases.
I kept it simple to make sure the standard backtracer stays reliable.
Cc: mingo@elte.hu
Signed-off-by: Andi Kleen <ak@suse.de>
Lockdep can call the dwarf2 unwinder early, and the dwarf2 code
uses safe_smp_processor_id which tries to access the local APIC page.
But that doesn't work before the APIC code has set up its fixmap.
Check for this case and always return boot cpu then.
Cc: jbeulich@novell.com
Cc: mingo@elte.hu
Signed-off-by: Andi Kleen <ak@suse.de>
- Remove unused all_contexts parameter
No caller used it
- Move skip argument into the structure (needed for
followon patches)
Cc: mingo@elte.hu
Signed-off-by: Andi Kleen <ak@suse.de>
Instead of hackish manual parsing
Requires earlier i386 patchkit, but also fixes i386 early_printk again.
I removed some obsolete really early parameters which didn't do anything useful.
Also made a few parameters that needed it early (mostly oops printing setup)
Also removed one panic check that wasn't visible without
early console anyways (the early console is now initialized after that
panic)
This cleans up a lot of code.
Signed-off-by: Andi Kleen <ak@suse.de>
This patch replaces the open-coded early commandline parsing
throughout the i386 boot code with the generic mechanism (already used
by ppc, powerpc, ia64 and s390). The code was inconsistent with
whether it deletes the option from the cmdline or not, meaning some of
these will get passed through the environment into init.
This transformation is mainly mechanical, but there are some notable
parts:
1) Grammar: s/linux never set's it up/linux never sets it up/
2) Remove hacked-in earlyprintk= option scanning. When someone
actually implements CONFIG_EARLY_PRINTK, then they can use
early_param().
[AK: actually it is implemented, but I'm adding the early_param it in the next
x86-64 patch]
3) Move declaration of generic_apic_probe() from setup.c into asm/apic.h
4) Various parameters now moved into their appropriate files (thanks Andi).
5) All parse functions which examine arg need to check for NULL,
except one where it has subtle humor value.
AK: readded acpi_sci handling which was completely dropped
AK: moved some more variables into acpi/boot.c
Cc: len.brown@intel.com
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Lock sections don't work the new dwarf2 unwinder
This generates slightly smaller code. It adds one more taken
jump to the fast path.
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Lock sections don't work the new dwarf2 unwinder
This generates slightly smaller code. It adds one more taken
jump to the fast path.
Also move the trampolines into semaphore.S and add proper CFI
annotations.
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Lock sections don't work the new dwarf2 unwinder
This generates slightly smaller code. It adds one more taken
jump to the fast path.
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Move the tce_table_kva array, disabled bitmap and bus_to_phb array
into a new per bus 'struct calgary_bus_info'. Also slightly reorganize
build_tce_table and tce_table_setparms to avoid exporting bus_info to
tce.c.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Rearrange struct members loosely based on size for improved alignment
and to save a few bytes.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The genapic field and the accessor macro weren't used anywhere.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
... instead of using a CONFIG option. The config option still controls
if the resulting executable actually has unwind information.
This is useful to prevent compilation errors when users select
CONFIG_STACK_UNWIND on old binutils and also allows to use
CFI in the future for non kernel debugging applications.
Cc: jbeulich@novell.com
Cc: sam@ravnborg.org
Signed-off-by: Andi Kleen <ak@suse.de>
They did not really belong into io_apic.c. Move them into a new file
and clean it up a bit.
Also remove outdated ATI quirk that was obsolete,
Signed-off-by: Andi Kleen <ak@suse.de>
PIC mode is an outdated way to drive the APICs that was used on
some early MP boards. It is not supported in the ACPI model.
It is unlikely to be ever configured by any x86-64 system
Remove it thus.
Signed-off-by: Andi Kleen <ak@suse.de>
- Convert CR* accesses to dedicated inline functions and rewrite
the rest as C inlines
- Don't do a double flush for global flushes (pointed out by Zach Amsden)
This was a bug workaround for old CPUs that don't do 64bit and is obsolete.
- Add a proper memory clobber to invlpg
- Remove an unused extern
Signed-off-by: Andi Kleen <ak@suse.de>
IO-APIC or local APIC can only be disabled at runtime anyways and
Kconfig has forced these options on for a long time now.
The Kconfigs are kept only now for the benefit of the shared acpi
boot.c code.
Signed-off-by: Andi Kleen <ak@suse.de>
- Move them to a pure assembly file. Previously they were in
a C file that only consisted of inline assembly. Doing it in pure
assembler is much nicer.
- Add a frame.i include with FRAME/ENDFRAME macros to easily
add frame pointers to assembly functions
- Add dwarf2 annotation to them so that the new dwarf2 unwinder
doesn't get stuck on them
- Random cleanups
Includes feedback from Jan Beulich and a UML build fix from Andrew
Morton.
Cc: jbeulich@novell.com
Cc: jdike@addtoit.com
Signed-off-by: Andi Kleen <ak@suse.de>
LOCK_PREFIX is replaced by nops on UP systems, so it has to be a special
macro. Previously this was only possible from C. Allow it for pure
assembly files too. Similar to earlier x86-64 patch.
Signed-off-by: Andi Kleen <ak@suse.de>
Previously it didn't align. Use the same one as the C compiler
in blended mode, which is good for K8 and Core2 and doesn't hurt
on P4.
Signed-off-by: Andi Kleen <ak@suse.de>
rwlocks are now out of line, so it near never triggers. Also it was
incompatible with the new dwarf2 unwinder because it had unannotiatable
push/pops.
Signed-off-by: Andi Kleen <ak@suse.de>
- Move the slow path fallbacks to their own assembly files
This makes them much easier to read and is needed for the next change.
- Add CFI annotations for unwinding (XXX need review)
- Remove constant case which can never happen with out of line spinlocks
- Use patchable LOCK prefixes
- Don't use lock sections anymore for inline code because they can't
be expressed by the unwinder (this adds one taken jump to the lock
fast path)
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
This ports the algorithm from x86-64 (with improvements) to i386.
Previously this only worked for frame pointer enabled kernels.
But spinlocks have a very simple stack frame that can be manually
analyzed. Do this.
Signed-off-by: Andi Kleen <ak@suse.de>
Hello,
Following my discussion with Andi. Here is a patch that introduces
two new TIF flags to simplify the context switch code in __switch_to().
The idea is to minimize the number of cache lines accessed in the common
case, i.e., when neither the debug registers nor the I/O bitmap are used.
This patch covers the x86-64 modifications. A patch for i386 follows.
Changelog:
- add TIF_DEBUG to track when debug registers are active
- add TIF_IO_BITMAP to track when I/O bitmap is used
- modify __switch_to() to use the new TIF flags
<signed-off-by>: eranian@hpl.hp.com
Signed-off-by: Andi Kleen <ak@suse.de>
For NUMA optimization and some other algorithms it is useful to have a fast
to get the current CPU and node numbers in user space.
x86-64 added a fast way to do this in a vsyscall. This adds a generic
syscall for other architectures to make it a generic portable facility.
I expect some of them will also implement it as a faster vsyscall.
The cache is an optimization for the x86-64 vsyscall optimization. Since
what the syscall returns is an approximation anyways and user space
often wants very fast results it can be cached for some time. The norma
methods to get this information in user space are relatively slow
The vsyscall is in a better position to manage the cache because it has direct
access to a fast time stamp (jiffies). For the generic syscall optimization
it doesn't help much, but enforce a valid argument to keep programs
portable
I only added an i386 syscall entry for now. Other architectures can follow
as needed.
AK: Also added some cleanups from Andrew Morton
Signed-off-by: Andi Kleen <ak@suse.de>
This patch adds a vgetcpu vsyscall, which depending on the CPU RDTSCP
capability uses either the RDTSCP or CPUID to obtain a CPU and node
numbers and pass them to the program.
AK: Lots of changes over Vojtech's original code:
Better prototype for vgetcpu()
It's better to pass the cpu / node numbers as separate arguments
to avoid mistakes when going from SMP to NUMA.
Also add a fast time stamp based cache using a user supplied
argument to speed things more up.
Use fast method from Chuck Ebbert to retrieve node/cpu from
GDT limit instead of CPUID
Made sure RDTSCP init is always executed after node is known.
Drop printk
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch adds initalization of the RDTSCP auxilliary values to CPU numbers
to time.c. If RDTSCP is available, the MSRs are written with the respective
values. It can be later used to initalize per-cpu timekeeping variables.
AK: Some cleanups. Move externs into headers and fix CPU hotplug.
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch adds macros for reading tsc via the RDTSCP instruction, as well
as writing the auxilliary MSR read by RDTSCP to msr.h
[AK: changed rdtscp definition for old binutils]
Signed-off-by: Vojtech Pavlik <vojtech@suse.cz>
Signed-off-by: Andi Kleen <ak@suse.de>
AK: This redoes the changes I temporarily reverted.
Intel now has support for Architectural Performance Monitoring Counters
( Refer to IA-32 Intel Architecture Software Developer's Manual
http://www.intel.com/design/pentium4/manuals/253669.htm ). This
feature is present starting from Intel Core Duo and Intel Core Solo processors.
What this means is, the performance monitoring counters and some performance
monitoring events are now defined in an architectural way (using cpuid).
And there will be no need to check for family/model etc for these architectural
events.
Below is the patch to use this performance counters in nmi watchdog driver.
Patch handles both i386 and x86-64 kernels.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
When a unknown NMI happened the panic would claim a NMI watchdog timeout.
Also it would check the variable set by nmi_watchdog=panic and panic then.
Fix up the panic message to be generic
Unconditionally panic on unknown NMI when panic on unknown nmi is enabled.
Noticed by Jan Beulich
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Making NMI suspend/resume work with SMP. We use CPU hotplug to offline
APs in SMP suspend/resume. Only BSP executes sysdev's .suspend/.resume
method. APs should follow CPU hotplug code path.
And:
+From: Don Zickus <dzickus@redhat.com>
Makes the start/stop paths of nmi watchdog more robust to handle the
suspend/resume cases more gracefully.
AK: I merged the two patches together
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Don Zickus <dzickus@redhat.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
To quote Alan Cox:
The default Linux behaviour on an NMI of either memory or unknown is to
continue operation. For many environments such as scientific computing
it is preferable that the box is taken out and the error dealt with than
an uncorrected parity/ECC error get propogated.
A small number of systems do generate NMI's for bizarre random reasons
such as power management so the default is unchanged. In other respects
the new proc/sys entry works like the existing panic controls already in
that directory.
This is separate to the edac support - EDAC allows supported chipsets to
handle ECC errors well, this change allows unsupported cases to at least
panic rather than cause problems further down the line.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Adds a new /proc/sys/kernel/nmi call that will enable/disable the nmi
watchdog.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Removes the un/set_nmi_callback and reserve/release_lapic_nmi functions as
they are no longer needed. The various subsystems are modified to register
with the die_notifier instead.
Also includes compile fixes by Andrew Morton.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
We need TIF_RESTORE_SIGMASK in order to support ppoll() and pselect()
system calls. This patch originally came from Andi, and was based
heavily on David Howells' implementation of same on i386. I fixed a typo
which was causing do_signal() to use the wrong signal mask.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch cleans up the NMI interrupt path. Instead of being gated by if
the 'nmi callback' is set, the interrupt handler now calls everyone who is
registered on the die_chain and additionally checks the nmi watchdog,
reseting it if enabled. This allows more subsystems to hook into the NMI if
they need to (without being block by set_nmi_callback).
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch includes the changes to make the nmi watchdog on i386 SMP aware.
A bunch of code was moved around to make it simpler to read. In addition,
it is now possible to determine if a particular NMI was the result of the
watchdog or not. This feature allows the kernel to filter out unknown NMIs
easier.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch includes the changes to make the nmi watchdog on x86_64 SMP
aware. A bunch of code was moved around to make it simpler to read. In
addition, it is now possible to determine if a particular NMI was the result
of the watchdog or not. This feature allows the kernel to filter out
unknown NMIs easier.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Adds basic infrastructure to allow subsystems to reserve performance
counters on the x86 chips. Only UP kernels are supported in this patch to
make reviewing easier. The SMP portion makes a lot more changes.
Think of this as a locking mechanism where each bit represents a different
counter. In addition, each subsystem should also reserve an appropriate
event selection register that will correspond to the performance counter it
will be using (this is mainly neccessary for the Pentium 4 chips as they
break the 1:1 relationship to performance counters).
This will help prevent subsystems like oprofile from interfering with the
nmi watchdog.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
There are some machines around (large xSeries or Unisys ES7000) that
need physical IO-APIC destination mode to access all of their IO
devices. This currently doesn't work in UP kernels as used in
distribution installers.
This patch allows to compile even UP kernels as GENERICARCH which
allows to use physical or clustered APIC mode.
Signed-off-by: Andi Kleen <ak@suse.de>
There is a potential deadlock in the driver core. It boils down to
the fact that bus_remove_device() calls klist_remove() instead of
klist_del(), thereby waiting until the reference count of the
klist_node in the bus's klist of devices drops to 0. The refcount
can't reach 0 so long as a modprobe process is trying to bind a new
driver to the device being removed, by calling __driver_attach(). The
problem is that __driver_attach() tries to acquire the device's
parent's semaphore, but the caller of bus_remove_device() is quite
likely to own that semaphore already.
It isn't sufficient just to replace klist_remove() with klist_del().
Doing so runs the risk that the device would remain on the bus's klist
of devices for some time, and so could be bound to another driver even
after it was unregistered. What's needed is a new way to distinguish
whether or not a device is registered, based on a criterion other than
whether its klist_node is linked into the bus's klist of devices. That
way driver binding can fail when the device is unregistered, even if
it is still linked into the klist.
This patch (as782) implements the solution, by adding a new bitflag to
indiate when a struct device is registered, by testing the flag before
allowing a driver to bind a device, and by changing the definition of
the device_is_registered() inline.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the infrastructure for drivers to do a threaded probe, and
waits at init time for all currently outstanding probes to complete.
A new kernel thread will be created when the probe() function for the
driver is called, if the multithread_probe bit is set in the driver
saying it can support this kind of operation.
I have tested this with USB and PCI, and it works, and shaves off a lot
of time in the boot process, but there are issues with finding root boot
disks, and some USB drivers assume that this can never happen, so it is
currently not enabled for any bus type. Individual drivers can enable
this right now if they wish, and bus authors can selectivly turn it on
as well, once they determine that their subsystem will work properly
with it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't be crufty. Mark it __must_check too.
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We get hundreds of these:
include/media/v4l2-dev.h:348: warning: ignoring return value of 'class_device_create_file', declared with attribute warn_unused_result
Handle it, and propagate the __must_check back a level.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Those 1500 warnings can be a bit of a pain. Add a config option to shut them
up.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We're getting a lot of crashes in the sysfs/kobject/device/bus/class code and
they're very hard to diagnose.
I'm suspecting that in some cases this is because drivers aren't checking
return values and aren't handling errors correctly. So the code blithely
blunders on and crashes later in very obscure ways.
There's just no reason to ignore errors which can and do occur. So the patch
sprinkles __must_check all over these APIs.
Causes 1,513 new warnings. Heh.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make sysfs_remove_bin_file() void. If it detects an error,
printk the file name and call dump_stack().
sysfs_hash_and_remove() now returns an error code indicating
its success or failure so that sysfs_remove_bin_file() can
know success/failure.
Convert the only driver that checked the return value of
sysfs_remove_bin_file().
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Makes it easier for devices to create and remove binary attribute files
so they don't have to call directly into sysfs. This is needed to help
with the conversion from struct class_device to struct device.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When moving class_device usage over to device, we need to handle
class_interfaces properly with devices. This patch adds that support.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This change creates a devices/virtual/CLASS_NAME tree for struct devices
that belong to a class, yet do not have a "real" struct device for a
parent. It automatically creates the directories on the fly as needed.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds two new callbacks to the class structure:
int (*dev_uevent)(struct device *dev, char **envp, int num_envp,
char *buffer, int buffer_size);
void (*dev_release)(struct device *dev);
And one pointer:
struct device_attribute * dev_attrs;
which all corrispond with the same thing as the "normal" class devices
do, yet this is for when a struct device is bound to a class.
Someday soon, struct class_device will go away, and then the other
fields in this structure can be removed too. But this is necessary in
order to get the transition to work properly.
Tested out on a network core patch that converted it to use struct
device instead of struct class_device.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed for the network class devices in order to be able to
convert over to use struct device.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Teach platform_bus about the new suspend_late/resume_early PM calls,
issued with IRQs off. Do we really need sysdev and friends any more,
or can janitors start switching its users over to platform_device so
we can do a minor code-ectomy?
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the new suspend_prepare() phase. It doesn't seem very usable,
has never been tested, doesn't address fault cleanup, and would need
a sibling resume_complete(); plus there are no real use cases. It
could be restored later if those issues get resolved.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a new pm_message_t event type to use when preparing to restore a
swsusp snapshot. Devices that have been initialized by Linux after resume
(rather than left in power-up-reset state) may need to be reset; this new
event type give drivers the chance to do that.
The drivers that will care about this are those which understand more hardware
states than just "on" and "reset", relying on hardware state during resume()
methods to be either the state left by the preceding suspend(), or a
power-lost reset. The best current example of this class of drivers are USB
host controller drivers, which currently do not work through swsusp when
they're statically linked.
When the swsusp freeze/thaw mechanism kicks in, a troublesome third state
could exist: one state set up by a different kernel instance, before a
snapshot image is resumed. This mechanism lets drivers prevent that state.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Changes the PCI core to use the new suspend infrastructure changes.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Allow devices to participate in the suspend process more intimately,
in particular, allow the final phase (with interrupts disabled) to
also be open to normal devices, not just system devices.
Also, allow classes to participate in device suspend.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NetLabel]: update docs with website information
[NetLabel]: rework the Netlink attribute handling (part 2)
[NetLabel]: rework the Netlink attribute handling (part 1)
[Netlink]: add nla_validate_nested()
[NETLINK]: add nla_for_each_nested() to the interface list
[NetLabel]: change the SELinux permissions
[NetLabel]: make the CIPSOv4 cache spinlocks bottom half safe
[NetLabel]: correct improper handling of non-NetLabel peer contexts
[TCP]: make cubic the default
[TCP]: default congestion control menu
[ATM] he: Fix __init/__devinit conflict
[NETFILTER]: Add dscp,DSCP headers to header-y
[DCCP]: Introduce dccp_probe
[DCCP]: Use constants for CCIDs
[DCCP]: Introduce constants for CCID numbers
[DCCP]: Allow default/fallback service code.
Assume that a cpu is *physically* offlined at boot time...
Because smpboot.c::smp_boot_cpu_map() canoot find cpu's sapicid,
numa.c::build_cpu_to_node_map() cannot build cpu<->node map for
offlined cpu.
For such cpus, cpu_to_node map should be fixed at cpu-hot-add.
This mapping should be done before cpu onlining.
This patch also handles cpu hotremove case.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add logic to check ARP request / reply packets used for ARP
monitor link integrity checking.
The current method simply examines the slave device to see if it
has sent and received traffic; this can be fooled by extraneous traffic.
For example, if multiple hosts running bonding are behind a common
switch, the probe traffic from the multiple instances of bonding will
update the tx/rx times on each other's slave devices.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add priv_flag to specifically identify bonding-involved devices. Needed
because IFF_MASTER is an unreliable identifier (vlan interfaces above bonding
will inherit IFF_MASTER). Misidentification of devices would cause
notifier events for other devices to be erroneously processed by bonding,
causing various havoc.
Bug discovered by Martin Papik <martin.papik@ipsec.info>; this patch is
modified from his original.
Signed-off-by: Martin Papik <martin.papik@ipsec.info>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
At the suggestion of Thomas Graf, rewrite NetLabel's use of Netlink attributes
to better follow the common Netlink attribute usage.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function, nla_validate_nested(), to validate nested Netlink
attributes.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the top of include/net/netlink.h is a list of Netlink interfaces, however,
the nla_for_each_nested() macro was not listed. This patch adds this interface
to the list at the top of the header file.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a problem where NetLabel would always set the value of
sk_security_struct->peer_sid in selinux_netlbl_sock_graft() to the context of
the socket, causing problems when users would query the context of the
connection. This patch fixes this so that the value in
sk_security_struct->peer_sid is only set when the connection is NetLabel based,
otherwise the value is untouched.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is version 21 of the Wireless Extensions. Changelog :
o finishes migrating the ESSID API (remove the +1)
o netdev->get_wireless_stats is no more
o long/short retry
This is a redacted version of a patch originally submitted by Jean
Tourrilhes. I removed most of the additions, in order to minimize
future support requirements for nl80211 (or other WE successor).
CC: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They all contain the same thing. Instead, have a single generic one in
include/asm-generic, and permit an arch to override as needed.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Mostly clean up CONFIG_OMAP_RESET_CLOCKS. Also includes a
patch from Imre Deak to make McSPI clocks use id.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch syncs OMAP DMA code with linux-omap tree.
Mostly allow changing DMA callback function and set
OMAP2 specific transfer mode.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add enable/disable functions which effectively control the GPT iclk and fclk.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for assigning memory regions dynamically to peripherals
attached to GPMC interface. Platform specific code should now call
gpmc_cs_request to get a free GPMC memory region instead of using
a fixed address.
Make the H4 and Apollon platform initialization use the new API.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds some further #defines regarding GPIOs and latch bits for
the Amstrad Delta; the drivers that use them will be submitted at a
later date but there's no reason not to have the information already
there and available for use.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds pin mux info for the SPI master/slave interface on
OMAP16xx. Data from OMAP 1611/1612 TRM and errata. Works for me on my
1611/H2 with current git kernel.
Signed-off-by: Mark Howell <mhowell@northlink.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Apollon board MMC supports on OMAP2
TODO:
We have to check MMC on H4
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Thomas Gleixner noticed that bitops.h should also use the raw_* irq
disable/enable variants, and __xchg needs them as well.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the IO-Data GLAN Tank, from Martin Michlmayr.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Thecus n2100 (80219-based.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
gcc 4.1's __typeof__ propagates 'const', which breaks get_unaligned().
Rewrite get_unaligned() not to use __typeof__.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The memory mapping for the Osiris machine
are all off by one bit, and the base address
has been fixed for writing (bit25 is being
checked by the write, but not on read)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the iop32x code isn't iop321-specific, and the iop33x code isn't
iop331-specfic, do a s/iop321/iop32x/ and s/iop331/iop33x/, and tidy up
the code to conform to the coding style guidelines somewhat better.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Factor out the register defines for a number of other peripherals
common to the iop32x and iop33x.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Revamp the iop3xx board support: move the support code for each iop
board type into its own file, start using platform serial and platform
physmap flash devices, switch to a per-board time tick rate, and get
rid of the ARCH_EP80219 and STEPD config options by doing the relevant
checks at run time.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Squeeze three instructions out of the iop32x irq demuxer, and nine
out of the iop33x irq demuxer by using the hardware vector generator.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement the gpio_line_{config,get,set} API for iop3xx.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Get rid of the unused IOP3??_IRQ_OFS irq offset define, start IRQ
numbering from zero.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add CP6 enable/disable sequences to the timekeeping code and the IRQ
code. As a result, we can't depend on CP6 access being enabled when
we enter get_irqnr_and_base anymore, so switch the latter over to
using memory-mapped accesses for now.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add macros to enable and disable access to CP6. On the iop3xx, enabling
CP6 access unfortunately also enables access to that coprocessor from
unprivileged code, so we need these macros to enable and disable access
to the coprocessor whenever we need to access it.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Switch the iop32x and iop33x code over to the common time implementation,
and remove the (nearly identical) iop32x and iop33x time implementations.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge and rewrite the iop32x/iop33x time code to do lost jiffy
tracking properly, and put the result in plat-iop/time.c.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Switch the iop32x and iop33x code over to the common PCI implementation,
and remove the (nearly identical) iop32x and iop33x PCI implementations.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge the iop32x PCI code and iop33x PCI code into plat-iop/pci.c.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the i2c bits shared between iop32x and iop33x to plat-iop/i2c.c
and include/asm-arm/hardware/iop3xx.h.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce the arch/arm/plat-iop directory, for code shared between the
iop32x and iop33x, and move the common memory map setup bits there.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Split the iop3xx mach type into iop32x and iop33x -- split the config
symbols, and move the code in the mach-iop3xx directory to the mach-iop32x
and mach-iop33x directories.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename CONFIG_ARCH_IOP321 to CONFIG_ARCH_IOP32X and
CONFIG_ARCH_IOP331 to CONFIG_ARCH_IOP33X.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Prevent userland from mapping in physical address regions >= 4G by
checking for that in valid_mmap_phys_addr_range().
Unfortunately, we cannot override valid_mmap_phys_addr_range() without
also overriding valid_phys_addr_range(), so copy drivers/char/mem.c's
version of valid_phys_addr_range() over to arch/arm/mm/mmap.c as well.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that we have raw_* variants of local_irq_$FOO(), switch the atomic
helpers over to use those raw_* variants. This is necessary when using
lockdep on pre-ARMv6 hardware, as lockdep uses atomic_t counters in the
trace_hardirqs_off() path.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow each CPU type in the S3C24XX range to
select the DMA channel mapping it supports.
We change the DMA registration to use an
virtual channel number that the DMA system
will allocate to a hardware channel at
request time.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add base definitions for the AC97 register
definitions.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds xt_dscp.h and xt_DSCP.h to the kernel headers which are
exported via 'make headers_install'. These are necessary for userspace
to add rules using dscp match and DSCP target.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (28 commits)
ocfs2: Teach ocfs2_drop_lock() to use ->set_lvb() callback
ocfs2: Remove ->unblock lockres operation
ocfs2: move downconvert worker to lockres ops
ocfs2: Remove unused dlmglue functions
ocfs2: Have the metadata lock use generic dlmglue functions
ocfs2: Add ->set_lvb callback in dlmglue
ocfs2: Add ->check_downconvert callback in dlmglue
ocfs2: Check for refreshing locks in generic unblock function
ocfs2: don't unconditionally pass LVB flags
ocfs2: combine inode and generic blocking AST functions
ocfs2: Add ->get_osb() dlmglue locking operation
ocfs2: remove ->unlock_ast() callback from ocfs2_lock_res_ops
ocfs2: combine inode and generic AST functions
ocfs2: Clean up lock resource refresh flags
ocfs2: Remove i_generation from inode lock names
ocfs2: Encode i_generation in the meta data lvb
ocfs2: Free up some space in the lvb
ocfs2: Remove special casing for inode creation in ocfs2_dentry_attach_lock()
ocfs2: manually d_move() during ocfs2_rename()
[PATCH] Allow file systems to manually d_move() inside of ->rename()
...
Some file systems want to manually d_move() the dentries involved in a
rename. We can do this by making use of the FS_ODD_RENAME flag if we just
have nfs_rename() unconditionally do the d_move(). While there, we rename
the flag to be more descriptive.
OCFS2 uses this to protect that part of the rename operation with a cluster
lock.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This has been discussed on dccp@vger and removes the necessity for applications
to supply service codes in each and every case.
If an application does not want to provide a service code, that's fine, it will
be given 0. Otherwise, service codes can be set via socket options as before.
This patch has been tested using various client/server configurations
(including listening on multiple service codes).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (50 commits)
[libata] Delete pata_it8172 driver
[PATCH] libata: improve handling of diagostic fail (and hardware that misreports it)
[PATCH] libata: fix non-uniform ports handling
Fix libata resource conflict for legacy mode
[libata] ata_piix: build fix
[PATCH] pata_amd: Check enable bits on Nvidia
[PATCH] Update SiS PATA
[libata] Add pata_jmicron driver to Kconfig, Makefile
[libata #pata-drivers] Trim trailing whitespace.
[libata] Trim trailing whitespace.
[libata] Add a bunch of PATA drivers.
Rename libata-bmdma.c to libata-sff.c.
libata: Grand renaming.
Clean up drivers/ata/Kconfig a bit.
[PATCH] CONFIG_PM=n slim: drivers/scsi/sata_sil*
[PATCH] sata_via: Add SATA support for vt8237a
[PATCH] libata: change path to libata in libata.tmpl
[PATCH] libata: s/CONFIG_SCSI_SATA/CONFIG_[S]ATA/g in pci/quirks.c
libata: Make sure drivers/ata is a separate Kconfig menu
[libata] ata_piix: add missing kfree()
...
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (217 commits)
net/ieee80211: fix more crypto-related build breakage
[PATCH] Spidernet: add ethtool -S (show statistics)
[NET] GT96100: Delete bitrotting ethernet driver
[PATCH] mv643xx_eth: restrict to 32-bit PPC_MULTIPLATFORM
[PATCH] Cirrus Logic ep93xx ethernet driver
r8169: the MMIO region of the 8167 stands behin BAR#1
e1000, ixgb: Remove pointless wrappers
[PATCH] Remove powerpc specific parts of 3c509 driver
[PATCH] s2io: Switch to pci_get_device
[PATCH] gt96100: move to pci_get_device API
[PATCH] ehea: bugfix for register access functions
[PATCH] e1000 disable device on PCI error
drivers/net/phy/fixed: #if 0 some incomplete code
drivers/net: const-ify ethtool_ops declarations
[PATCH] ethtool: allow const ethtool_ops
[PATCH] sky2: big endian
[PATCH] sky2: fiber support
[PATCH] sky2: tx pause bug fix
drivers/net: Trim trailing whitespace
[PATCH] ehea: IBM eHEA Ethernet Device Driver
...
Manually resolved conflicts in drivers/net/ixgb/ixgb_main.c and
drivers/net/sky2.c related to CHECKSUM_HW/CHECKSUM_PARTIAL changes by
commit 84fa7933a3 that just happened to be
next to unrelated changes in this update.
Some MMC hosts can only handle log2 block sizes. Unfortunately,
the MMC password support needs to be able to send non-log2 block
sizes. Provide a capability so that the MMC password support can
decide whether it should use this support or not.
The unfortunate side effect of this host limitation is that any
MMC card protected by a password which is not a log2 block size
can not be accessed on a host which only allows a log2 block size.
This change just adds the flag. The MMC password support code
needs updating to use it (if and when it is finally submitted.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Key more of the domain validation settings off the inquiry data from
the disk (in particular, don't try IU or DT unless the disk claims to
support them.
Also add a new dv_in_progress flag to prevent recursive DV.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* 'linus' of master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa: (148 commits)
[ALSA] intel8x0m - Free irq in suspend
[ALSA] Move CONFIG_SND_AC97_POWER_SAVE to pci/Kconfig
[ALSA] usb-audio: add mixer control names for the Aureon 5.1 MkII
[ALSA] ES1938: remove duplicate field initialization
[ALSA] usb-audio: increase number of packets per URB
[ALSA] hda-codec - Fix headphone auto-toggle on sigmatel codec
[ALSA] hda-intel - A slight cleanup of timeout check in azx_get_response()
[ALSA] hda-codec - Fix mic input with STAC92xx codecs
[ALSA] mixart: Use SEEK_{SET,CUR,END} instead of hardcoded values
[ALSA] gus: Use SEEK_{SET,CUR,END} instead of hardcoded values
[ALSA] opl4: Use SEEK_{SET,CUR,END} instead of hardcoded values
[ALSA] sound core: Use SEEK_{SET,CUR,END} instead of hardcoded values
[ALSA] hda-codec - Support multiple headphone pins
[ALSA] hda_intel prefer 24bit instead of 20bit
[ALSA] hda-codec - Add vendor ids for Motorola and Conexant
[ALSA] hda-codec - Add device id for Motorola si3054-compatible codec
[ALSA] Add missing compat ioctls for ALSA control API
[ALSA] powermac - Fix Oops when conflicting with aoa driver
[ALSA] aoa: add locking to tas codec
[ALSA] hda-intel - Fix suspend/resume with MSI
...
* git://git.linux-nfs.org/pub/linux/nfs-2.6: (74 commits)
NFS: unmark NFS direct I/O as experimental
NFS: add comments clarifying the use of nfs_post_op_update()
NFSv4: rpc_mkpipe creating socket inodes w/out sk buffers
NFS: Use SEEK_END instead of hardcoded value
NFSv4: When mounting with a port=0 argument, substitute port=2049
NFSv4: Poll more aggressively when handling NFS4ERR_DELAY
NFSv4: Handle the condition NFS4ERR_FILE_OPEN
NFSv4: Retry lease recovery if it failed during a synchronous operation.
NFS: Don't invalidate the symlink we just stuffed into the cache
NFS: Make read() return an ESTALE if the file has been deleted
NFSv4: It's perfectly legal for clp to be NULL here....
NFS: nfs_lookup - don't hash dentry when optimising away the lookup
SUNRPC: Fix Oops in pmap_getport_done
SUNRPC: Add refcounting to the struct rpc_xprt
SUNRPC: Clean up soft task error handling
SUNRPC: Handle ENETUNREACH, EHOSTUNREACH and EHOSTDOWN socket errors
SUNRPC: rpc_delay() should not clobber the rpc_task->tk_status
Fix a referral error Oops
NFS: NFS_ROOT should use the new rpc_create API
NFS: Fix up compiler warnings on 64-bit platforms in client.c
...
Manually resolved conflict in net/sunrpc/xprtsock.c
Remove IPGA volume controls and merge the IPGA range to ADC volume
controls. These two volumes are not really independent but connected
simply in different ranges 0-0x7f and 0x80-max. It doesn't make sense
to provide two controls.
Since both 0x7f and 0x80 specify 0dB, a hack is needed for IPGA range
to skip 0x80 (increment one) for such controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch adds a new attribute, pcm_class, to each PCM sysfs entry.
It's useful to detect what kind of PCM stream is, for example, HAL
can check whether it's a modem or not.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the definition of TLV dB range compound. It contains one or
more dB-range or linear-volume TLV entries with min/max ranges.
Used for volume controls with non-linear curves.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
- Clean up the code in AK4xxx-ADDA i2c code.
- Fix capture gain controls for AK5365
- Changed the static table for DAC/ADC mixer labels to use
structs
- Implemented TLV entries for each AK codec
The volumes in AK4524, AK4528 and AK5365 are corrected with
a table to be suitable for dB conversion.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the definition of linear volume TLV type.
Some DSP chips and codecs (e.g. AK codec) use linear volume control.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the dB scale information to vxpocket and vx222 drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Add support for the AK5365 ADC.
Signed-off-by: Jochen Voss <voss@seehuhn.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The flag to avoid 32bit-incompatible mmap for control/status records
should be outside the pcm substream instance since a substream can be
shared among multiple opens. Now it's flagged in pcm_file list that
is directly assigned to file->private_data.
Also, removed snd_pcm_add_file() and remove_file() functions and
substream.files field that are not really used in the code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Remove unused tlv_rw field from struct snd_kcontrol. The callback is
set in tlv.c field, instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added CONFIG_SND_AC97_POWER_SAVE kernel config to enable the support
of aggressive AC97 power-saving mode. In this mode, the AC97
powerdown register bits are dynamically controlled at each open/close
of PCM streams.
The mode is activated via power_save option for snd-ac97-codec
driver. As default it's off. It can be turned on/off on the fly
via sysfs, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Orignally proposed by Sam Revitch <sam.revitch@gmail.com>.
Unregister device files at disconnection to avoid the futher accesses.
Also, the dev_unregister callback is removed and replaced with the
combination of disconnect + free.
A new function snd_card_free_when_closed() is introduced, which is
used in USB disconnect callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
- Add the linked list to each proc entry to enable a single-shot
disconnection (unregister)
- Deprecate snd_info_unregister(), use snd_info_free_entry()
- Removed NULL checks of snd_info_free_entry()
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch implements a TLV mechanism to transfer an additional information
like dB scale to the user space. The types might be extended in future.
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
In a subsequent patch, this will allow the portmapper to take a reference
to the rpc_xprt for which it is updating the port number, fixing an Oops.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Now that we have a copy of the symlink path in the page cache, we can pass
a struct page down to the XDR routines instead of a string buffer.
Test plan:
Connectathon, all NFS versions.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
If the LOOKUP or GETATTR in nfs_instantiate fail, nfs_instantiate will do a
d_drop before returning. But some callers already do a d_drop in the case
of an error return. Make certain we do only one d_drop in all error paths.
This issue was introduced because over time, the symlink proc API diverged
slightly from the create/mkdir/mknod proc API. To prevent other coding
mistakes of this type, change the symlink proc API to be more like
create/mkdir/mknod and move the nfs_instantiate call into the symlink proc
routines so it is used in exactly the same way for create, mkdir, mknod,
and symlink.
Test plan:
Connectathon, all versions of NFS.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The two function call API for creating a new RPC client is now obsolete.
Remove it.
Also, remove an unnecessary check to see whether the caller is capable of
using privileged network services. The kernel RPC client always uses a
privileged ephemeral port by default; callers are responsible for checking
the authority of users to make use of any RPC service, or for specifying
that a nonprivileged port is acceptable.
Test plan:
Repeated runs of Connectathon locking suite. Check network trace to ensure
correctness of NLM requests and replies.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Prepare for more generic transport endpoint handling needed by transports
that might use different forms of addressing, such as IPv6.
Introduce a single function call to replace the two-call
xprt_create_proto/rpc_create_client API. Define a new rpc_create_args
structure that allows callers to pass in remote endpoint addresses of
varying length.
Test-plan:
Compile kernel with CONFIG_NFS enabled.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Remove some unused macros related to accessing an RPC peer address
Test plan:
Compile kernel with CONFIG_NFS option enabled.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
IPv6 addresses are big (128 bytes). Now that no RPC client consumers treat
the addr field in rpc_xprt structs as an opaque, and access it only via the
API calls, we can safely widen the field in the rpc_xprt struct to
accomodate larger addresses.
Test plan:
Compile kernel with CONFIG_NFS enabled.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Provide an API for formatting the remote peer address for printing without
exposing its internal structure. The address could be dynamic, so we
support a function call to get the address rather than reading it straight
out of a structure.
Test-plan:
Destructive testing (unplugging the network temporarily). Probably need
to rig a server where certain services aren't running, or that returns an
error for some typical operation.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add a new method to the transport switch API to provide a way to convert
the opaque contents of xprt->addr to a human-readable string.
Test plan:
Compile kernel with CONFIG_NFS enabled.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
include/linux/sunrpc/clnt.h already includes include/linux/sunrpc/xprt.h.
We can remove xprt.h from source files that already include clnt.h.
Likewise include/linux/sunrpc/timer.h.
Test plan:
Compile kernel with CONFIG_NFS enabled.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Provide an API for retrieving the remote peer address without allowing
direct access to the rpc_xprt struct.
Test-plan:
Compile kernel with CONFIG_NFS enabled.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Introduce a clean transport switch API for plugging in different types of
rpcbind mechanisms. For instance, rpcbind can cleanly replace the
existing portmapper client, or a transport can choose to implement RPC
binding any way it likes.
Test plan:
Destructive testing (unplugging the network temporarily). Connectathon
with UDP and TCP. NFSv2/3 and NFSv4 mounting should be carefully checked.
Probably need to rig a server where certain services aren't running, or
that returns an error for some typical operation.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The previous patches removed the last user of RPC child tasks, so we can
remove support for child tasks from net/sunrpc/sched.c now.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Move connection and bind state that was maintained in the rpc_clnt
structure to the rpc_xprt structure. This will allow the creation of
a clean API for plugging in different types of bind mechanisms.
This brings improvements such as the elimination of a single spin lock to
control serialization for all in-kernel RPC binding. A set of per-xprt
bitops is used to serialize tasks during RPC binding, just like it now
works for making RPC transport connections.
Test-plan:
Destructive testing (unplugging the network temporarily). Connectathon
with UDP and TCP. NFSv2/3 and NFSv4 mounting should be carefully checked.
Probably need to rig a server where certain services aren't running, or
that returns an error for some typical operation.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Hide the contents and format of xprt->addr by eliminating direct uses
of the xprt->addr.sin_port field. This change is required to support
alternate RPC host address formats (eg IPv6).
Test-plan:
Destructive testing (unplugging the network temporarily). Repeated runs of
Connectathon locking suite with UDP and TCP.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The attached patch makes NFS share superblocks between mounts from the same
server and FSID over the same protocol.
It does this by creating each superblock with a false root and returning the
real root dentry in the vfsmount presented by get_sb(). The root dentry set
starts off as an anonymous dentry if we don't already have the dentry for its
inode, otherwise it simply returns the dentry we already have.
We may thus end up with several trees of dentries in the superblock, and if at
some later point one of anonymous tree roots is discovered by normal filesystem
activity to be located in another tree within the superblock, the anonymous
root is named and materialises attached to the second tree at the appropriate
point.
Why do it this way? Why not pass an extra argument to the mount() syscall to
indicate the subpath and then pathwalk from the server root to the desired
directory? You can't guarantee this will work for two reasons:
(1) The root and intervening nodes may not be accessible to the client.
With NFS2 and NFS3, for instance, mountd is called on the server to get
the filehandle for the tip of a path. mountd won't give us handles for
anything we don't have permission to access, and so we can't set up NFS
inodes for such nodes, and so can't easily set up dentries (we'd have to
have ghost inodes or something).
With this patch we don't actually create dentries until we get handles
from the server that we can use to set up their inodes, and we don't
actually bind them into the tree until we know for sure where they go.
(2) Inaccessible symbolic links.
If we're asked to mount two exports from the server, eg:
mount warthog:/warthog/aaa/xxx /mmm
mount warthog:/warthog/bbb/yyy /nnn
We may not be able to access anything nearer the root than xxx and yyy,
but we may find out later that /mmm/www/yyy, say, is actually the same
directory as the one mounted on /nnn. What we might then find out, for
example, is that /warthog/bbb was actually a symbolic link to
/warthog/aaa/xxx/www, but we can't actually determine that by talking to
the server until /warthog is made available by NFS.
This would lead to having constructed an errneous dentry tree which we
can't easily fix. We can end up with a dentry marked as a directory when
it should actually be a symlink, or we could end up with an apparently
hardlinked directory.
With this patch we need not make assumptions about the type of a dentry
for which we can't retrieve information, nor need we assume we know its
place in the grand scheme of things until we actually see that place.
This patch reduces the possibility of aliasing in the inode and page caches for
inodes that may be accessed by more than one NFS export. It also reduces the
number of superblocks required for NFS where there are many NFS exports being
used from a server (home directory server + autofs for example).
This in turn makes it simpler to do local caching of network filesystems, as it
can then be guaranteed that there won't be links from multiple inodes in
separate superblocks to the same cache file.
Obviously, cache aliasing between different levels of NFS protocol could still
be a problem, but at least that gives us another key to use when indexing the
cache.
This patch makes the following changes:
(1) The server record construction/destruction has been abstracted out into
its own set of functions to make things easier to get right. These have
been moved into fs/nfs/client.c.
All the code in fs/nfs/client.c has to do with the management of
connections to servers, and doesn't touch superblocks in any way; the
remaining code in fs/nfs/super.c has to do with VFS superblock management.
(2) The sequence of events undertaken by NFS mount is now reordered:
(a) A volume representation (struct nfs_server) is allocated.
(b) A server representation (struct nfs_client) is acquired. This may be
allocated or shared, and is keyed on server address, port and NFS
version.
(c) If allocated, the client representation is initialised. The state
member variable of nfs_client is used to prevent a race during
initialisation from two mounts.
(d) For NFS4 a simple pathwalk is performed, walking from FH to FH to find
the root filehandle for the mount (fs/nfs/getroot.c). For NFS2/3 we
are given the root FH in advance.
(e) The volume FSID is probed for on the root FH.
(f) The volume representation is initialised from the FSINFO record
retrieved on the root FH.
(g) sget() is called to acquire a superblock. This may be allocated or
shared, keyed on client pointer and FSID.
(h) If allocated, the superblock is initialised.
(i) If the superblock is shared, then the new nfs_server record is
discarded.
(j) The root dentry for this mount is looked up from the root FH.
(k) The root dentry for this mount is assigned to the vfsmount.
(3) nfs_readdir_lookup() creates dentries for each of the entries readdir()
returns; this function now attaches disconnected trees from alternate
roots that happen to be discovered attached to a directory being read (in
the same way nfs_lookup() is made to do for lookup ops).
The new d_materialise_unique() function is now used to do this, thus
permitting the whole thing to be done under one set of locks, and thus
avoiding any race between mount and lookup operations on the same
directory.
(4) The client management code uses a new debug facility: NFSDBG_CLIENT which
is set by echoing 1024 to /proc/net/sunrpc/nfs_debug.
(5) Clone mounts are now called xdev mounts.
(6) Use the dentry passed to the statfs() op as the handle for retrieving fs
statistics rather than the root dentry of the superblock (which is now a
dummy).
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Eliminate nfs_server::client_sys in favour of nfs_client::cl_rpcclient as we
only really need one per server that we're talking to since it doesn't have any
security on it.
The retransmission management variables are also moved to the common struct as
they're required to set up the cl_rpcclient connection.
The NFS2/3 client and client_acl connections are thenceforth derived by cloning
the cl_rpcclient connection and post-applying the authorisation flavour.
The code for setting up the initial common connection has been moved to
client.c as nfs_create_rpc_client(). All the NFS program definition tables are
also moved there as that's where they're now required rather than super.c.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Move the rpc_ops from the nfs_server struct to the nfs_client struct as they're
common to all server records of a particular NFS protocol version.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Maintain a common server record for NFS2/3 as well as for NFS4 so that common
stuff can be moved there from struct nfs_server.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add some extra const qualifiers into NFS.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Generalise the nfs_client structure by:
(1) Moving nfs_client to a more general place (nfs_fs_sb.h).
(2) Renaming its maintenance routines to be non-NFS4 specific.
(3) Move those maintenance routines to a new non-NFS4 specific file (client.c)
and move the declarations to internal.h.
(4) Make nfs_find/get_client() take a full sockaddr_in to include the port
number (will be required for NFS2/3).
(5) Make nfs_find/get_client() take the NFS protocol version (again will be
required to differentiate NFS2, 3 & 4 client records).
Also:
(6) Make nfs_client construction proceed akin to inodes, marking them as under
construction and providing a function to indicate completion.
(7) Make nfs_get_client() wait interruptibly if it finds a client that it can
share, but that client is currently being constructed.
(8) Make nfs4_create_client() use (6) and (7) instead of locking cl_sem.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add a set_capabilities NFS RPC op so that the server capabilities can be set.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add a lookup filehandle NFS RPC op so that a file handle can be looked up
without requiring dentries and inodes and other VFS stuff when doing an NFS4
pathwalk during mounting.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Return an error when starting the idmapping pipe so that we can detect it
failing.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Rename nfs_server::nfs4_state to nfs_client as it will be used to represent the
client state for NFS2 and NFS3 also.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Rename struct nfs4_client to struct nfs_client so that it can become the basis
for a general client record for NFS2 and NFS3 in addition to NFS4.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The attached patch adds a new directory cache management function that prepares
a disconnected anonymous function to be connected into the dentry tree. The
anonymous dentry is transferred the name and parentage from another dentry.
The following changes were made in [try #2]:
(*) d_materialise_dentry() now switches the parentage of the two nodes around
correctly when one or other of them is self-referential.
The following changes were made in [try #7]:
(*) d_instantiate_unique() has had the interior part split out as function
__d_instantiate_unique(). Callers of this latter function must be holding
the appropriate locks.
(*) _d_rehash() has been added as a wrapper around __d_rehash() to call it
with the most obvious hash list (the one from the name). d_rehash() now
calls _d_rehash().
(*) d_materialise_dentry() is now __d_materialise_dentry() and is static.
(*) d_materialise_unique() added to perform the combination of d_find_alias(),
d_materialise_dentry() and d_add_unique() that the NFS client was doing
twice, all within a single dcache_lock critical section. This reduces the
number of times two different spinlocks were being accessed.
The following further changes were made:
(*) Add the dentries onto their parents d_subdirs lists.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The current access cache only allows one entry at a time to be cached for each
inode. Add a per-inode red-black tree in order to allow more than one to
be cached at a time.
Should significantly cut down the time spent in path traversal for shared
directories such as ${PATH}, /usr/share, etc.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
several targets have no ....at() family and m32r calls its only chown variant
chown32(), with __NR_chown being undefined. creat(2) is also absent in some
targets.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Cirrus Logic ep93xx is an ARM SoC that includes an ethernet MAC
-- this patch adds a driver for that ethernet MAC.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Relevant SA queries are actually "greater than" / "less than", not
"greater than or equal" / "less than or equal" as the names imply.
(See IB spec 1.2 Vol 1, 15.2.5.16 PATHRECORD/Table 205 PathRecord)
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Document the reject sending and modifying QP to error done in rdma_accept().
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clarify that rdma_destroy_id cancels outstanding asynchronous operations on the
Associated id.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Require users to register with SA module, to prevent the sa_query
module text from going away while an SA query callback is still
running. Update all in-tree users for the new interface.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Modifications to the existing rdma header files, core files, drivers,
and ulp files to support iWARP, including:
- Hook iWARP CM into the build system and use it in rdma_cm.
- Convert enum ib_node_type to enum rdma_node_type, which includes
the possibility of RDMA_NODE_RNIC, and update everything for this.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add an iWARP Connection Manager (CM), which abstracts connection
management for iWARP devices (RNICs). It is a logical instance of the
xx_cm where xx is the transport type (ib or iw). The symbols exported
are used by the transport independent rdma_cm module, and are
available also for transport dependent ULPs.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Pass a struct ib_udata to the low-level driver's ->modify_srq() and
->modify_qp() methods, so that it can get to the device-specific data
passed in by the userspace driver.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a ib_uverbs_resize_cq_resp.driver_data field so that low-level
drivers can return data from a resize CQ operation to userspace. Have
ib_uverbs_resize_cq() only copy the cqe field, to avoid having to bump
the userspace ABI.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IFA_F_HOMEADDRESS is introduced for Mobile IPv6 Home Addresses on
Mobile Node.
The IFA_F_HOMEADDRESS flag should be set for Mobile IPv6 Home
Addresses for 2 purposes. 1) We need to check this on receipt of
Type 2 Routing Header (RFC3775 Secion 6.4), 2) We prefer Home
Address(es) in source address selection (RFC3484 Section 5 Rule 4).
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IFA_F_NODAD flag, similar to IN6_IFF_NODAD in BSDs, is introduced
to skip DAD.
This flag should be set to Mobile IPv6 Home Address(es) on Mobile
Node because DAD would fail if we should perform DAD; our Home Agent
protects our Home Address(es).
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not always need proxy NDP functionality even we
enable forwarding.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have sent NA with router flag from the node-wide forwarding
configuration. This is not appropriate for proxy NA, and it should be
set according to each proxy entry's configuration.
This is used by Mobile IPv6 home agent to support physical home link
in acting as a proxy router for mobile node which is not a router,
for example.
Based on MIPL2 kernel patch.
Signed-off-by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
When the master PPTP connection times out while still having unfullfilled
expectations (and a GRE keymap entry) associated with it, the keymap entry
is not destroyed.
Add a destroy callback to struct ip_conntrack_helper and use it to destroy
PPTP siblings when the master is destroyed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated expectation handling in the NAT helper and simplify
the remains in the conntrack helper.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a few header definitions to match RFC2637. Most importantly the
PptpOutCallRequest header included an invalid padding field and a
size check was disabled because of this.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conntrack structure contains the call ID in host byte order for no
reason, get rid of back and forth conversions.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split the xt_compat_match/xt_compat_target into smaller type-safe functions
performing just one operation. Handle all alignment and size-related
conversions centrally in these function instead of requiring each module to
implement a full-blown conversion function. Replace ->compat callback by
->compat_from_user and ->compat_to_user callbacks, responsible for
converting just a single private structure.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
