Enable the port when disabling countermeasures, and disable it on
enabling countermeasures.
This bug causes the response of the system to certain attacks to be
ineffective.
It also prevents wpa_supplicant from getting scan results, as
wpa_supplicant disables countermeasures on startup - preventing the
hardware from scanning.
wpa_supplicant works with ap_mode=2 despite this bug because the commit
handler re-enables the port.
The log tends to look like:
State: DISCONNECTED -> SCANNING
Starting AP scan for wildcard SSID
Scan requested (ret=0) - scan timeout 5 seconds
EAPOL: disable timer tick
EAPOL: Supplicant port status: Unauthorized
Scan timeout - try to get results
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 1 sec 0 usec
Starting AP scan for wildcard SSID
Scan requested (ret=-1) - scan timeout 5 seconds
Failed to initiate AP scan.
Reported by: Giacomo Comes <comes@naic.edu>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... and interface up.
In these situations, you are usually trying to connect to a new AP, so
keeping TKIP countermeasures active is confusing. This is already how
the driver behaves (inadvertently). However, querying SIOCGIWAUTH may
tell userspace that countermeasures are active when they aren't.
Clear the setting so that the reporting matches what the driver has
done..
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW has to be set to FULLSLEEP mode during suspend,
when no interface has been brought up. Not doing this would
break resume, as the chip won't be powered up at all.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This results in an erroneus num_adhoc_vifs count, as the this counter
was incremented but not decremented for mesh interfaces.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interrupt handler takes a lock - but since commit bcad6e80f3 this
lock goes through an indirection specified in the hermes_t structure.
We must therefore initialise the structure before setting up the
interrupt handler.
Fix orinoco_cs and spectrum_cs
<https://bugzilla.kernel.org/show_bug.cgi?id=23932>
Bisected by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon tasklet is accesssing the bslot info for beacon generation.
Meanwhile the same slot can be freed on interface deletion.
Current the remove_interface disables the beacon alert after freeing the slot.
This may leads to null pointer access.
This patch disables SWBA and kills the beacon tasklet to prevent access
to the slot to be freed. After releasing the slot, swba will be enabled again
upon the availablity of beaconing interfaces.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.
Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.
Able to pass Wifi Test case 5.2.18 with this fix.
Cc: Stable <stable@kernel.org> (2.6.36+)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ath_drain_all_txq fails to stop DMA, it issues a hw reset. This reset
happens at a very problematic point in time, when the hardware rx path has
not been stopped yet. This could lead to memory corruption, hardware hangs
or other issues.
To fix these issues, simply remove the reset entirely and check the tx DMA
stop status to prevent problems with fast channel changes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k driver subtracts 3 dBm to the txpower as with two radios the
signal power is doubled.
The resulting value is assigned in an u16 which overflows and makes
the card work at full power.
Cc: stable@kernel.org
Signed-off-by: Matteo Croce <matteo@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 916448e77f.
"As far as I can tell, either of these patches breaks multiple VIF
scenarios. I'm not sure exactly why, but I had to revert this to
get any of my interfaces to associate."
-- Ben Greear <greearb@candelatech.com>
http://marc.info/?l=linux-wireless&m=129123368719339&w=2
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few LNA control related flags were also specified as a bitfields, however
for some strange reason they were written in big-endian order this time.
Fix this by using flags instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parsing data using bitfields is messy, because it makes endian handling
much harder. AR9002 and earlier got it right, AR9003 got it wrong.
This might lead to either using too high or too low tx power values,
depending on frequency and eeprom settings.
Fix it by getting rid of the CTL related bitfields entirely and use
masks instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The register which gives input gpio state is 0x404c for ar9003,
currently 0x4048 is wrongly used. This will disable RF and make
it unusable on some of AR9003.
Cc:stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Atheros 3011 has small sflash firmware and needs to be
blacklisted in transport driver to load actual firmware
in DFU driver.
Signed-off-by: Bala Shanmugam <sbalashanmugam@atheros.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
If a device is autosuspended an inability to resubmit URBs is
to be expected. Check the error code and only log real errors.
(Now that autosuspend is default enabled for btusb, those log
messages were happening all the time e.g. with a BT mouse)
Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.
Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.
Able to pass Wifi Test case 5.2.18 with this fix.
Cc: Stable <stable@kernel.org> (2.6.36+)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Th commit titled "mac80211: clean up rx handling wrt. found_sta"
removed found_sta variable which caused a MIC failure event
to be reported twice for a single failure to supplicant resulted
in STA disconnect.
This should fix WPA specific countermeasures WiFi test case (5.2.17)
issues with mac80211 based drivers which report MIC failure events in
rx status.
Cc: Stable <stable@kernel.org> (2.6.37)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an curious issue due to insufficient
rx frame filtering.
Saqeb Akhter reported frequent disconnects while streaming
videos over samba: <http://marc.info/?m=128600031109136>
> [ 1166.512087] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [ 1526.059997] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [ 2125.324356] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [...]
The reason is that the device generates frames with slightly
bogus SA/TA addresses.
e.g.:
[ 2314.402316] Ignore 9f:1f:31:f8:64:ff
[ 2314.402321] Ignore 9f:1f:31:f8:64:ff
[ 2352.453804] Ignore 0d:1f:31:f8:64:ff
[ 2352.453808] Ignore 0d:1f:31:f8:64:ff
^^ the group-address flag is set!
(the correct SA/TA would be: 00:1f:31:f8:64:ff)
Since the AP does not know from where the frames come, it
generates a DEAUTH response for the (invalid) mcast address.
This mcast deauth frame then passes through all filters and
tricks the stack into thinking that the AP brutally kicked
us!
This patch fixes the problem by simply ignoring
non-broadcast, group-addressed deauth/disassoc frames.
Cc: Jouni Malinen <j@w1.fi>
Cc: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Saqeb Akhter <saqeb.akhter@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit: "carl9170: revamp carl9170_tx_prepare"
introduced a peculiar bug that would only show
up if the the module parameter noht is set to 1.
Then all outbound voice, video and background
frames would each invoke a (bogus) RTS/CTS
handshake.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order for frame injection to work properly for some use cases
(e.g., finding the station entry and keys for encryption), mac80211
needs to find the correct sdata entry. This works when the main vif
is in AP mode, but commit a2c1e3dad5
broke this particular use case for station main vif. While this type of
injection is quite unusual operation, it has some uses and we should fix
it. Do this by changing the monitor vif sdata selection to allow station
vif to be selected instead of limiting it to just AP vifs. We still need
to skip some iftypes to avoid selecting unsuitable vif for injection.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
while removing beaconing mode interface, SWBA interrupt
was never disabled when there are no other beaconing interfaces.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With some upcoming changes we'd like to use
the interface types for P2P capability tests.
Enable them now so that when we add those
tests in wpa_supplicant, nothing will break.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k driver uses a shared pm_qos_request_list structure for all
devices. This causes the following warning if more than one device is
present in the system:
WARNING: at kernel/pm_qos_params.c:234 ath9k_init_device+0x5e8/0x6b0()
pm_qos_add_request() called for already added request
Modules linked in:
Call Trace:
[<802b1cdc>] dump_stack+0x8/0x34
[<8007dd90>] warn_slowpath_common+0x78/0xa4
[<8007de44>] warn_slowpath_fmt+0x2c/0x38
[<801b0828>] ath9k_init_device+0x5e8/0x6b0
[<801bc508>] ath_pci_probe+0x2dc/0x39c
[<80176254>] pci_device_probe+0x64/0xa4
[<8019471c>] driver_probe_device+0xbc/0x188
[<80194854>] __driver_attach+0x6c/0xa4
[<80193e20>] bus_for_each_dev+0x60/0xb0
[<80193580>] bus_add_driver+0xcc/0x268
[<80194c08>] driver_register+0xe0/0x198
[<801764e0>] __pci_register_driver+0x50/0xe0
[<80365f48>] ath9k_init+0x3c/0x6c
[<8006050c>] do_one_initcall+0xfc/0x1d8
[<80355340>] kernel_init+0xd4/0x174
[<800639a4>] kernel_thread_helper+0x10/0x18
---[ end trace 5345fc6f870564a6 ]---
This patch fixes that warning by using a separate pm_qos_request_list
sructure for each device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
card->priv must not be accessed after lbs_remove_card() was called
as lbs_remove_card() frees card->priv via free_netdev().
For libertas_sdio this is a regression introduced by 23b149c189.
The correct fix to the issue described there is simply to remove the
assignment. This flag is set at the appropriate time inside
lbs_remove_card anyway.
Reported-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"priv" is stored at the end of the wiphy structure, which is freed
during the call to lbs_cfg_free(). It must not be touched afterwards.
Remove the unnecessary NULL assignment causing this memory corruption.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix unbalanced call to sdio_release_host() on the error path.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new vendor for Broadcom 4318.
Signed-off-by: Daniel Klaffenbach <danielklaffenbach@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems that using ath9k_hw_stoppcurecv to stop rx dma is not enough.
When it's time to stop DMA, the PCU is still busy, so the rx enable
bit never clears.
Using ath9k_hw_abortpcurecv helps with getting rx stopped much faster,
with this change, I cannot reproduce the rx stop related WARN_ON anymore.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting tid information in the TX header is required only for QoS
frames. Not handling this case causes severe data loss with some APs.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This follows wireless-testing 9236d838c9
("cfg80211: fix extension channel checks to initiate communication") and
fixes accidental case fall-through. Without this fix, HT40 is entirely
blocked.
Signed-off-by: Mark Mentovai <mark@moxienet.com>
Cc: stable@kernel.org
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When operating in a mode that initiates communication and using
HT40 we should fail if we cannot use both primary and secondary
channels to initiate communication. Our current ht40 allowmap
only covers STA mode of operation, for beaconing modes we need
a check on the fly as the mode of operation is dynamic and
there other flags other than disable which we should read
to check if we can initiate communication.
Do not allow for initiating communication if our secondary HT40
channel has is either disabled, has a passive scan flag, a
no-ibss flag or is a radar channel. Userspace now has similar
checks but this is also needed in-kernel.
Reported-by: Jouni Malinen <jouni.malinen@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9287 based PCI & USB devices are differed in eeprom start offset.
So set proper the offset for HTC devices to read nvram correctly.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Treat new PIDs (0xA704, 0x1200) as AR7010 devices.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added new VID/PIDs into supported devices list
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update pm_qos before removing it in deinit_device to prevent this
warning:
pm_qos_update_request() called for unknown object.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
usb_wait_anchor_empty_timeout's @timeout
wants milliseconds and not jiffies.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WIPHY_FLAG_IBSS_RSN is BIT(7) as is WIPHY_FLAG_CONTROL_PORT_PROTOCOL. Change
to BIT(8).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When b43legacy is compiled on the arm platform, the following errors are seen:
CC [M] drivers/net/wireless/b43legacy/xmit.o
In file included from include/net/dst.h:11,
from drivers/net/wireless/b43legacy/xmit.c:31:
include/net/dst_ops.h:28: error: expected ':', ',', ';', '}' or '__attribute__'
before '____cacheline_aligned_in_smp'
include/net/dst_ops.h: In function 'dst_entries_get_fast':
include/net/dst_ops.h:33: error: 'struct dst_ops' has no member named
'pcpuc_entries'
include/net/dst_ops.h: In function 'dst_entries_get_slow':
include/net/dst_ops.h:41: error: 'struct dst_ops' has no member named
'pcpuc_entries'
include/net/dst_ops.h: In function 'dst_entries_add':
include/net/dst_ops.h:49: error: 'struct dst_ops' has no member named
'pcpuc_entries'
include/net/dst_ops.h: In function 'dst_entries_init':
include/net/dst_ops.h:55: error: 'struct dst_ops' has no member named
'pcpuc_entries'
include/net/dst_ops.h: In function 'dst_entries_destroy':
include/net/dst_ops.h:60: error: 'struct dst_ops' has no member named
'pcpuc_entries'
make[4]: *** [drivers/net/wireless/b43legacy/xmit.o] Error 1
make[3]: *** [drivers/net/wireless/b43legacy] Error 2
make[2]: *** [drivers/net/wireless] Error 2
make[1]: *** [drivers/net] Error 2
make: *** [drivers] Error 2
The cause is a missing include of <linux/cache.h>, which is present for
i386 and x86_64 architectures, but not for arm.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to use build-in debugging macro, pci_dev in priv need to be
assigned first.
This fix iwl3945 driver oopsed at boot with 2.6.37-rc1
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This cause 'No Bonding' to be used if userspace has not yet been paired
with remote device since the l2cap socket used to create the rfcomm
session does not have any security level set.
Signed-off-by: Luiz Augusto von Dentz <luiz.dentz-von@nokia.com>
Acked-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Last commit added a wrong endianness conversion. Fixing that.
Reported-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
In function l2cap_get_conf_opt() and l2cap_add_conf_opt() the address of
opt->val sometimes is not at the edge of 2-bytes/4-bytes, so 2-bytes/4 bytes
access will cause data misalignment exeception. Use get_unaligned_le16/32
and put_unaligned_le16/32 function to avoid data misalignment execption.
Signed-off-by: steven miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
