dist_queue is no longer used since commit 37922ea4a3
("tipc: permit overlapping service ranges in name table")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Hoang Huu Le <hoang.h.le@dektech.com.au>
Link: https://lore.kernel.org/r/20201028032712.31009-1-hoang.h.le@dektech.com.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net/ipv6/calipso.c:1236: warning: Excess function parameter 'reg' description in 'calipso_req_delattr'
net/ipv6/calipso.c:1236: warning: Function parameter or member 'req' not described in 'calipso_req_delattr'
net/ipv6/calipso.c:435: warning: Excess function parameter 'audit_secid' description in 'calipso_doi_remove'
net/ipv6/calipso.c:435: warning: Function parameter or member 'audit_info' not described in 'calipso_doi_remove'
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028013344.931928-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net/ipv6/rpl_iptunnel.c:15: warning: cannot understand function prototype: 'struct rpl_iptunnel_encap '
The header on the file containing the author copyright message uses
kerneldoc /** opener. This confuses the parser when it gets to
struct rpl_iptunnel_encap {
struct ipv6_rpl_sr_hdr srh[0];
};
Similarly:
net//ipv6/rpl.c:10: warning: Function parameter or member 'x' not described in 'IPV6_PFXTAIL_LEN'
where IPV6_PFXTAIL_LEN is a macro definition, not a function.
Convert the header comments to a plain /* comment.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028013123.931816-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net//ipv4/tcp_lp.c:120: warning: Function parameter or member 'sk' not described in 'tcp_lp_cong_avoid'
net//ipv4/tcp_lp.c:135: warning: Function parameter or member 'sk' not described in 'tcp_lp_remote_hz_estimator'
net//ipv4/tcp_lp.c:188: warning: Function parameter or member 'sk' not described in 'tcp_lp_owd_calculator'
net//ipv4/tcp_lp.c:222: warning: Function parameter or member 'rtt' not described in 'tcp_lp_rtt_sample'
net//ipv4/tcp_lp.c:222: warning: Function parameter or member 'sk' not described in 'tcp_lp_rtt_sample'
net//ipv4/tcp_lp.c:265: warning: Function parameter or member 'sk' not described in 'tcp_lp_pkts_acked'
net//ipv4/tcp_lp.c:97: warning: Function parameter or member 'sk' not described in 'tcp_lp_init'
There are still a few kerneldoc warnings after this fix.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028012703.931632-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net/dccp/ccids/ccid2.c:190: warning: Function parameter or member 'hc' not described in 'ccid2_update_used_window'
net/dccp/ccids/ccid2.c:190: warning: Function parameter or member 'new_wnd' not described in 'ccid2_update_used_window'
net/dccp/ccids/ccid2.c:360: warning: Function parameter or member 'sk' not described in 'ccid2_rtt_estimator'
net/dccp/ccids/ccid3.c:112: warning: Function parameter or member 'sk' not described in 'ccid3_hc_tx_update_x'
net/dccp/ccids/ccid3.c:159: warning: Function parameter or member 'hc' not described in 'ccid3_hc_tx_update_s'
net/dccp/ccids/ccid3.c:268: warning: Function parameter or member 'sk' not described in 'ccid3_hc_tx_send_packet'
net/dccp/ccids/ccid3.c:667: warning: Function parameter or member 'sk' not described in 'ccid3_first_li'
net/dccp/ccids/ccid3.c:85: warning: Function parameter or member 'hc' not described in 'ccid3_update_send_interval'
net/dccp/ccids/lib/loss_interval.c:85: warning: Function parameter or member 'lh' not described in 'tfrc_lh_update_i_mean'
net/dccp/ccids/lib/loss_interval.c:85: warning: Function parameter or member 'skb' not described in 'tfrc_lh_update_i_mean'
net/dccp/ccids/lib/packet_history.c:392: warning: Function parameter or member 'h' not described in 'tfrc_rx_hist_sample_rtt'
net/dccp/ccids/lib/packet_history.c:392: warning: Function parameter or member 'skb' not described in 'tfrc_rx_hist_sample_rtt'
net/dccp/feat.c:1003: warning: Function parameter or member 'dreq' not described in 'dccp_feat_server_ccid_dependencies'
net/dccp/feat.c:1040: warning: Function parameter or member 'array_len' not described in 'dccp_feat_prefer'
net/dccp/feat.c:1040: warning: Function parameter or member 'array' not described in 'dccp_feat_prefer'
net/dccp/feat.c:1040: warning: Function parameter or member 'preferred_value' not described in 'dccp_feat_prefer'
net/dccp/output.c:151: warning: Function parameter or member 'dp' not described in 'dccp_determine_ccmps'
net/dccp/output.c:242: warning: Function parameter or member 'sk' not described in 'dccp_xmit_packet'
net/dccp/output.c:305: warning: Function parameter or member 'sk' not described in 'dccp_flush_write_queue'
net/dccp/output.c:305: warning: Function parameter or member 'time_budget' not described in 'dccp_flush_write_queue'
net/dccp/output.c:378: warning: Function parameter or member 'sk' not described in 'dccp_retransmit_skb'
net/dccp/qpolicy.c:88: warning: Function parameter or member '' not described in 'dccp_qpolicy_operations'
net/dccp/qpolicy.c:88: warning: Function parameter or member '{' not described in 'dccp_qpolicy_operations'
net/dccp/qpolicy.c:88: warning: Function parameter or member 'params' not described in 'dccp_qpolicy_operations'
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028011412.931250-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net//dcb/dcbnl.c:1836: warning: Function parameter or member 'app' not described in 'dcb_getapp'
net//dcb/dcbnl.c:1836: warning: Function parameter or member 'dev' not described in 'dcb_getapp'
net//dcb/dcbnl.c:1858: warning: Function parameter or member 'dev' not described in 'dcb_setapp'
net//dcb/dcbnl.c:1858: warning: Function parameter or member 'new' not described in 'dcb_setapp'
net//dcb/dcbnl.c:1899: warning: Function parameter or member 'app' not described in 'dcb_ieee_getapp_mask'
net//dcb/dcbnl.c:1899: warning: Function parameter or member 'dev' not described in 'dcb_ieee_getapp_mask'
net//dcb/dcbnl.c:1922: warning: Function parameter or member 'dev' not described in 'dcb_ieee_setapp'
net//dcb/dcbnl.c:1922: warning: Function parameter or member 'new' not described in 'dcb_ieee_setapp'
net//dcb/dcbnl.c:1953: warning: Function parameter or member 'del' not described in 'dcb_ieee_delapp'
net//dcb/dcbnl.c:1953: warning: Function parameter or member 'dev' not described in 'dcb_ieee_delapp'
net//dcb/dcbnl.c:1986: warning: Function parameter or member 'dev' not described in 'dcb_ieee_getapp_prio_dscp_mask_map'
net//dcb/dcbnl.c:1986: warning: Function parameter or member 'p_map' not described in 'dcb_ieee_getapp_prio_dscp_mask_map'
net//dcb/dcbnl.c:2016: warning: Function parameter or member 'dev' not described in 'dcb_ieee_getapp_dscp_prio_mask_map'
net//dcb/dcbnl.c:2016: warning: Function parameter or member 'p_map' not described in 'dcb_ieee_getapp_dscp_prio_mask_map'
net//dcb/dcbnl.c:2045: warning: Function parameter or member 'dev' not described in 'dcb_ieee_getapp_default_prio_mask'
For some of these warnings, change to comments to plain comments,
since no attempt is being made to follow kerneldoc syntax.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028010913.930929-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net//nfc/core.c:1046: warning: Function parameter or member 'tx_headroom' not described in 'nfc_allocate_device'
net//nfc/core.c:1046: warning: Function parameter or member 'tx_tailroom' not described in 'nfc_allocate_device'
net//nfc/core.c:198: warning: Excess function parameter 'protocols' description in 'nfc_start_poll'
net//nfc/core.c:198: warning: Function parameter or member 'im_protocols' not described in 'nfc_start_poll'
net//nfc/core.c:198: warning: Function parameter or member 'tm_protocols' not described in 'nfc_start_poll'
net//nfc/core.c:441: warning: Function parameter or member 'mode' not described in 'nfc_deactivate_target'
net//nfc/core.c:711: warning: Function parameter or member 'dev' not described in 'nfc_alloc_send_skb'
net//nfc/core.c:711: warning: Function parameter or member 'err' not described in 'nfc_alloc_send_skb'
net//nfc/core.c:711: warning: Function parameter or member 'flags' not described in 'nfc_alloc_send_skb'
net//nfc/core.c:711: warning: Function parameter or member 'sk' not described in 'nfc_alloc_send_skb'
net//nfc/digital_core.c:470: warning: Function parameter or member 'im_protocols' not described in 'digital_start_poll'
net//nfc/digital_core.c:470: warning: Function parameter or member 'nfc_dev' not described in 'digital_start_poll'
net//nfc/digital_core.c:470: warning: Function parameter or member 'tm_protocols' not described in 'digital_start_poll'
net//nfc/nci/core.c:1119: warning: Function parameter or member 'tx_headroom' not described in 'nci_allocate_device'
net//nfc/nci/core.c:1119: warning: Function parameter or member 'tx_tailroom' not described in 'nci_allocate_device'
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028005653.930467-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net/appletalk/aarp.c:68: warning: Function parameter or member 'dev' not described in 'aarp_entry'
net/appletalk/aarp.c:68: warning: Function parameter or member 'expires_at' not described in 'aarp_entry'
net/appletalk/aarp.c:68: warning: Function parameter or member 'hwaddr' not described in 'aarp_entry'
net/appletalk/aarp.c:68: warning: Function parameter or member 'last_sent' not described in 'aarp_entry'
net/appletalk/aarp.c:68: warning: Function parameter or member 'next' not described in 'aarp_entry'
net/appletalk/aarp.c:68: warning: Function parameter or member 'packet_queue' not described in 'aarp_entry'
net/appletalk/aarp.c:68: warning: Function parameter or member 'status' not described in 'aarp_entry'
net/appletalk/aarp.c:68: warning: Function parameter or member 'target_addr' not described in 'aarp_entry'
net/appletalk/aarp.c:68: warning: Function parameter or member 'xmit_count' not described in 'aarp_entry'
net/appletalk/ddp.c:1422: warning: Function parameter or member 'dev' not described in 'atalk_rcv'
net/appletalk/ddp.c:1422: warning: Function parameter or member 'orig_dev' not described in 'atalk_rcv'
net/appletalk/ddp.c:1422: warning: Function parameter or member 'pt' not described in 'atalk_rcv'
net/appletalk/ddp.c:1422: warning: Function parameter or member 'skb' not described in 'atalk_rcv'
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028005527.930388-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net/netlabel/netlabel_calipso.c:376: warning: Function parameter or member 'ops' not described in 'netlbl_calipso_ops_register'
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Paul Moore <paul@paul-moore.com>
Link: https://lore.kernel.org/r/20201028005350.930299-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net/l3mdev/l3mdev.c:249: warning: Function parameter or member 'arg' not described in 'l3mdev_fib_rule_match'
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20201028005059.930192-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net/openvswitch/flow.c:303: warning: Function parameter or member 'key_vh' not described in 'parse_vlan_tag'
net/openvswitch/flow.c:303: warning: Function parameter or member 'skb' not described in 'parse_vlan_tag'
net/openvswitch/flow.c:303: warning: Function parameter or member 'untag_vlan' not described in 'parse_vlan_tag'
net/openvswitch/vport.c:122: warning: Function parameter or member 'parms' not described in 'ovs_vport_alloc'
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028004849.930094-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net/llc/llc_conn.c:917: warning: Function parameter or member 'kern' not described in 'llc_sk_alloc'
net/llc/llc_conn.c:917: warning: Function parameter or member 'prot' not described in 'llc_sk_alloc'
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028004644.929997-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Andrew Lunn says:
====================
Markup some printk like functions
W=1 warns of functions which look like printk but don't have
attributes so the compile can check that arguments matches the format
string.
====================
Link: https://lore.kernel.org/r/20201028003849.929490-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net/tipc/netlink_compat.c: In function ‘tipc_tlv_sprintf’:
net/tipc/netlink_compat.c:137:2: warning: function ‘tipc_tlv_sprintf’ might be a candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
137 | n = vscnprintf(buf, rem, fmt, args);
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
net/dccp/ccid.c: In function ‘ccid_kmem_cache_create’:
net/dccp/ccid.c:85:2: warning: function ‘ccid_kmem_cache_create’ might be a candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
85 | vsnprintf(slab_name_fmt, CCID_SLAB_NAME_LENGTH, fmt, args);
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that the compiler is performing printf checking, we get the warning:
net/tipc/netlink_compat.c: In function ‘tipc_nl_compat_link_stat_dump’:
net/tipc/netlink_compat.c:591:39: warning: format ‘%s’ expects argument of type ‘char *’, but argument 3 has type ‘void *’ [-Wformat=]
591 | tipc_tlv_sprintf(msg->rep, "\nLink <%s>\n",
| ~^
| |
| char *
| %p
592 | nla_data(link[TIPC_NLA_LINK_NAME]));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| |
| void *
There is no nla_string(), so cast to a char *.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201028004333.929816-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov says:
====================
selftests: net: bridge: add tests for IGMPv3
This set adds tests for the bridge's new IGMPv3 support. The tests use
precooked packets which are sent via mausezahn and the resulting state
after each test is checked for proper X,Y sets, (*,G) source list, source
list entry timers, (S,G) existence and flags, packet forwarding and
blocking, exclude group expiration and (*,G) auto-add. The first 3 patches
prepare the existing IGMPv2 tests, then patch 4 adds new helpers which are
used throughout the rest of the v3 tests.
The following new tests are added:
- base case: IGMPv3 report 239.10.10.10 is_include (A)
- include -> allow report
- include -> is_include report
- include -> is_exclude report
- include -> to_exclude report
- exclude -> allow report
- exclude -> is_include report
- exclude -> is_exclude report
- exclude -> to_exclude report
- include -> block report
- exclude -> block report
- exclude timeout (move to include + entry deletion)
- S,G port entry automatic add to a *,G,exclude port
The variable names and set notation are the same as per RFC 3376,
for more information check RFC 3376 sections 4.2.15 and 6.4.1.
MLDv2 tests will be added by a separate patch-set.
====================
Link: https://lore.kernel.org/r/20201027185934.227040-1-razor@blackwall.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When we have *,G ports in exclude mode and a new S,G,port is added
the kernel has to automatically create an S,G entry for each exclude
port to get proper forwarding.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test that when a group in exclude mode expires it changes mode to
include and the blocked entries are deleted.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The test checks for the following case:
state report result action
EXCLUDE (X,Y) BLOCK (A) EXCLUDE (X+(A-Y),Y) (A-X-Y)=Group Timer
Send Q(G,A-Y)
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The test checks for the following case:
state report result action
INCLUDE (A) BLOCK (B) INCLUDE (A) Send Q(G,A*B)
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The test checks for the following case:
state report result action
EXCLUDE (X,Y) TO_EX (A) EXCLUDE (A-Y,Y*A) (A-X-Y)=Group Timer
Delete (X-A)
Delete (Y-A)
Send Q(G,A-Y)
Group Timer=GMI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The test checks for the following case:
state report result action
EXCLUDE (X,Y) IS_EX (A) EXCLUDE (A-Y,Y*A) (A-X-Y)=GMI
Delete (X-A)
Delete (Y-A)
Group Timer=GMI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The test checks for the following case:
state report result action
EXCLUDE (X,Y) IS_IN (A) EXCLUDE (X+A,Y-A) (A)=GMI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The test checks for the following case:
state report result action
EXCLUDE (X,Y) ALLOW (A) EXCLUDE (X+A,Y-A) (A)=GMI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The test checks for the following case:
state report result action
INCLUDE (A) TO_EX (B) EXCLUDE (A*B,B-A) (B-A)=0
Delete (A-B)
Send Q(G,A*B)
Group Timer=GMI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The test checks for the following case:
state report result action
INCLUDE (A) IS_EX (B) EXCLUDE (A*B,B-A) (B-A)=0
Delete (A-B)
Group Timer=GMI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The test checks for the following case:
state report result action
INCLUDE (A) IS_IN (B) INCLUDE (A+B) (B)=GMI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
First we test is_include/include mode then we build on that with allow
effectively achieving:
state report result action
INCLUDE (A) ALLOW (B) INCLUDE (A+B) (B)=GMI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add helpers which will be used in subsequent tests, they are:
- check_sg_entries: check for proper source list and S,G entry
existence
- check_sg_fwding: check for proper traffic forwarding/blocking
- check_sg_state: check for proper blocked/forwarding entry state
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We have to specifically check for udp protocol in addition to the mac
address because in IGMPv3 tests group-specific queries will use the same
mac address.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for one more argument which specifies the source address to
use. It will be later used for IGMPv3 S,G entry testing.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To prepare the bridge_igmp.sh for IGMPv3 we need to rename the
current test to IGMPv2.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor phy_led_trigger_register() and deduplicate its functionality
when registering LED trigger for link.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201027182146.21355-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch enables the HW LPI Timer which controls the automatic entry
and exit of the LPI state.
The EEE LPI timer value is configured through ethtool. The driver will
auto select the LPI HW timer if the value in the HW timer supported range.
Else, the driver will fallback to SW timer.
Signed-off-by: Vineetha G. Jaya Kumaran <vineetha.g.jaya.kumaran@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Link: https://lore.kernel.org/r/20201027160051.22898-1-weifeng.voon@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After I sent a fix for what appeared to be a harmless warning in
the wimax user interface code, the conclusion was that the whole
thing has most likely not been used in a very long time, and the
user interface possibly been broken since b61a5eea59 ("wimax: use
genl_register_family_with_ops()").
Using a shared branch between net-next and staging should help
coordinate patches getting submitted against it.
-----BEGIN PGP SIGNATURE-----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=PyFd
-----END PGP SIGNATURE-----
Merge tag 'wimax-staging' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground
Arnd Bergmann says:
====================
wimax: move to staging
After I sent a fix for what appeared to be a harmless warning in
the wimax user interface code, the conclusion was that the whole
thing has most likely not been used in a very long time, and the
user interface possibly been broken since b61a5eea59 ("wimax: use
genl_register_family_with_ops()").
Using a shared branch between net-next and staging should help
coordinate patches getting submitted against it.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
TIPC reserves 64 service types for current and future internal use.
Therefore, the bind() function is meant to block regular user sockets
from being bound to these values, while it should let through such
bindings from internal users.
However, since we at the design moment saw no way to distinguish
between regular and internal users the filter function ended up
with allowing all bindings of the reserved types which were really
in use ([0,1]), and block all the rest ([2,63]).
This is risky, since a regular user may bind to the service type
representing the topology server (TIPC_TOP_SRV == 1) or the one used
for indicating neighboring node status (TIPC_CFG_SRV == 0), and wreak
havoc for users of those services, i.e., most users.
The reality is however that TIPC_CFG_SRV never is bound through the
bind() function, since it doesn't represent a regular socket, and
TIPC_TOP_SRV can also be made to bypass the checks in tipc_bind()
by introducing a different entry function, tipc_sk_bind().
It should be noted that although this is a change of the API semantics,
there is no risk we will break any currently working applications by
doing this. Any application trying to bind to the values in question
would be badly broken from the outset, so there is no chance we would
find any such applications in real-world production systems.
v2: Added warning printout when a user is blocked from binding,
as suggested by Jakub Kicinski
Acked-by: Yung Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Link: https://lore.kernel.org/r/20201030012938.489557-1-jmaloy@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Unify the set of information returned by mii_ethtool_get_link_ksettings(),
mii_ethtool_gset() and phy_ethtool_ksettings_get(). Make the mii_*()
functions report advertised settings when autonegotiation if disabled.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Łukasz Stelmach <l.stelmach@samsung.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20201027114317.8259-1-l.stelmach@samsung.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Henrik Bjoernlund says:
====================
net: bridge: cfm: Add support for Connectivity Fault Management(CFM)
Connectivity Fault Management (CFM) is defined in 802.1Q
section 12.14.
Connectivity Fault Management (CFM) comprises capabilities for
detecting, verifying, and isolating connectivity failures in Virtual
Bridged Networks. These capabilities can be used in networks
operated by multiple independent organizations, each with restricted
management access to each other’s equipment.
CFM functions are partitioned as follows:
— Path discovery
— Fault detection
— Fault verification and isolation
— Fault notification
— Fault recovery
The primary CFM protocol shims are called Maintenance Points (MPs).
A MP can be either a MEP or a MHF.
The MEP:
-It is the Maintenance association End Point
described in 802.1Q section 19.2.
-It is created on a specific level (1-7) and is assuring
that no CFM frames are passing through this MEP on lower levels.
-It initiates and terminates/validates CFM frames on its level.
-It can only exist on a port that is related to a bridge.
The MHF:
-It is the Maintenance Domain Intermediate Point
(MIP) Half Function (MHF) described in 802.1Q section 19.3.
-It is created on a specific level (1-7).
-It is extracting/injecting certain CFM frame on this level.
-It can only exist on a port that is related to a bridge.
-Currently not supported.
There are defined the following CFM protocol functions:
-Continuity Check
-Loopback. Currently not supported.
-Linktrace. Currently not supported.
This CFM component supports create/delete of MEP instances and
configuration of the different CFM protocols. Also status information
can be fetched and delivered through notification due to defect
status change.
The user interacts with CFM using the 'cfm' user space client
program, the client talks with the kernel using netlink.
Any notification emitted by CFM from the kernel can be monitored in
user space by starting 'cfm_server' program.
Currently this 'cfm' and 'cfm_server' programs are standalone placed
in a cfm repository https://github.com/microchip-ung/cfm but it is
considered to integrate this into 'iproute2'.
v1 -> v2
Added the CFM switchdev interface and also added utilization by
calling the interface from the kernel CFM implementation trying
to offload CFM functionality to HW. This offload (CFM driver) is
currently not implemented.
Corrections based on RCF comments:
-The single CFM kernel implementation Patch is broken up into
three patches.
-Changed the list of MEP instances from list_head to
hlist_head.
-Removed unnecessary RCU list traversing.
-Solved RCU unlocking problem.
-Removed unnecessary comments.
-Added ASSERT_RTNL() where required.
-Shaping up on error messages.
-Correction NETLINK br_fill_ifinfo() to be able to handle
'filter_mask' with multiple flags asserted.
v2 -> v3
-The switchdev definition and utilization has been removed as
there was no switchdev implementation.
-Some compiling issues are fixed as Reported-by:
kernel test robot <lkp@intel.com>.
v3 -> v4
-Fixed potential crash during hlist walk where elements are
removed.
-Giving all commits unique titles.
-NETLINK implementation split into three commits.
-Commit "bridge: cfm: Bridge port remove" is merged with
commit "bridge: cfm: Kernel space implementation of CFM. MEP
create/delete."
v4 -> v5
-Reordered members in struct net_bridge to bring member
frame_type_list to the first cache line.
-Helper functions nla_get_mac() and nla_get_maid() are removed.
-The NLA_POLICY_NESTED() macro is used to initialize the
br_cfm_policy array.
-Fixed reverse xmas tree.
v5 -> v6
-Fixed that the SKB buffer was not freed during error handling return.
-Removed unused struct definition.
-Changed bool to u8 bitfields for space save.
-Utilizing the NETLINK policy validation feature.
v6 -> v7
-Removed check of parameters in br_cfm_mep_config_set() and
br_cfm_cc_peer_mep_add() in first commit of MEP implementation
(Patch 4 out of 10)
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
====================
Link: https://lore.kernel.org/r/20201027100251.3241719-1-henrik.bjoernlund@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is the implementation of Netlink notifications out of CFM.
Notifications are initiated whenever a state change happens in CFM.
IFLA_BRIDGE_CFM:
Points to the CFM information.
IFLA_BRIDGE_CFM_MEP_STATUS_INFO:
This indicate that the MEP instance status are following.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO:
This indicate that the peer MEP status are following.
CFM nested attribute has the following attributes in next level.
IFLA_BRIDGE_CFM_MEP_STATUS_INSTANCE:
The MEP instance number of the delivered status.
The type is NLA_U32.
IFLA_BRIDGE_CFM_MEP_STATUS_OPCODE_UNEXP_SEEN:
The MEP instance received CFM PDU with unexpected Opcode.
The type is NLA_U32 (bool).
IFLA_BRIDGE_CFM_MEP_STATUS_VERSION_UNEXP_SEEN:
The MEP instance received CFM PDU with unexpected version.
The type is NLA_U32 (bool).
IFLA_BRIDGE_CFM_MEP_STATUS_RX_LEVEL_LOW_SEEN:
The MEP instance received CCM PDU with MD level lower than
configured level. This frame is discarded.
The type is NLA_U32 (bool).
IFLA_BRIDGE_CFM_CC_PEER_STATUS_INSTANCE:
The MEP instance number of the delivered status.
The type is NLA_U32.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_PEER_MEPID:
The added Peer MEP ID of the delivered status.
The type is NLA_U32.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_CCM_DEFECT:
The CCM defect status.
The type is NLA_U32 (bool).
True means no CCM frame is received for 3.25 intervals.
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_RDI:
The last received CCM PDU RDI.
The type is NLA_U32 (bool).
IFLA_BRIDGE_CFM_CC_PEER_STATUS_PORT_TLV_VALUE:
The last received CCM PDU Port Status TLV value field.
The type is NLA_U8.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_IF_TLV_VALUE:
The last received CCM PDU Interface Status TLV value field.
The type is NLA_U8.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEEN:
A CCM frame has been received from Peer MEP.
The type is NLA_U32 (bool).
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_TLV_SEEN:
A CCM frame with TLV has been received from Peer MEP.
The type is NLA_U32 (bool).
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEQ_UNEXP_SEEN:
A CCM frame with unexpected sequence number has been received
from Peer MEP.
The type is NLA_U32 (bool).
When a sequence number is not one higher than previously received
then it is unexpected.
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is the implementation of CFM netlink status
get information interface.
Add new nested netlink attributes. These attributes are used by the
user space to get status information.
GETLINK:
Request filter RTEXT_FILTER_CFM_STATUS:
Indicating that CFM status information must be delivered.
IFLA_BRIDGE_CFM:
Points to the CFM information.
IFLA_BRIDGE_CFM_MEP_STATUS_INFO:
This indicate that the MEP instance status are following.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO:
This indicate that the peer MEP status are following.
CFM nested attribute has the following attributes in next level.
GETLINK RTEXT_FILTER_CFM_STATUS:
IFLA_BRIDGE_CFM_MEP_STATUS_INSTANCE:
The MEP instance number of the delivered status.
The type is u32.
IFLA_BRIDGE_CFM_MEP_STATUS_OPCODE_UNEXP_SEEN:
The MEP instance received CFM PDU with unexpected Opcode.
The type is u32 (bool).
IFLA_BRIDGE_CFM_MEP_STATUS_VERSION_UNEXP_SEEN:
The MEP instance received CFM PDU with unexpected version.
The type is u32 (bool).
IFLA_BRIDGE_CFM_MEP_STATUS_RX_LEVEL_LOW_SEEN:
The MEP instance received CCM PDU with MD level lower than
configured level. This frame is discarded.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_PEER_STATUS_INSTANCE:
The MEP instance number of the delivered status.
The type is u32.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_PEER_MEPID:
The added Peer MEP ID of the delivered status.
The type is u32.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_CCM_DEFECT:
The CCM defect status.
The type is u32 (bool).
True means no CCM frame is received for 3.25 intervals.
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_RDI:
The last received CCM PDU RDI.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_PEER_STATUS_PORT_TLV_VALUE:
The last received CCM PDU Port Status TLV value field.
The type is u8.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_IF_TLV_VALUE:
The last received CCM PDU Interface Status TLV value field.
The type is u8.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEEN:
A CCM frame has been received from Peer MEP.
The type is u32 (bool).
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_TLV_SEEN:
A CCM frame with TLV has been received from Peer MEP.
The type is u32 (bool).
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
IFLA_BRIDGE_CFM_CC_PEER_STATUS_SEQ_UNEXP_SEEN:
A CCM frame with unexpected sequence number has been received
from Peer MEP.
The type is u32 (bool).
When a sequence number is not one higher than previously received
then it is unexpected.
This is cleared after GETLINK IFLA_BRIDGE_CFM_CC_PEER_STATUS_INFO.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is the implementation of CFM netlink configuration
get information interface.
Add new nested netlink attributes. These attributes are used by the
user space to get configuration information.
GETLINK:
Request filter RTEXT_FILTER_CFM_CONFIG:
Indicating that CFM configuration information must be delivered.
IFLA_BRIDGE_CFM:
Points to the CFM information.
IFLA_BRIDGE_CFM_MEP_CREATE_INFO:
This indicate that MEP instance create parameters are following.
IFLA_BRIDGE_CFM_MEP_CONFIG_INFO:
This indicate that MEP instance config parameters are following.
IFLA_BRIDGE_CFM_CC_CONFIG_INFO:
This indicate that MEP instance CC functionality
parameters are following.
IFLA_BRIDGE_CFM_CC_RDI_INFO:
This indicate that CC transmitted CCM PDU RDI
parameters are following.
IFLA_BRIDGE_CFM_CC_CCM_TX_INFO:
This indicate that CC transmitted CCM PDU parameters are
following.
IFLA_BRIDGE_CFM_CC_PEER_MEP_INFO:
This indicate that the added peer MEP IDs are following.
CFM nested attribute has the following attributes in next level.
GETLINK RTEXT_FILTER_CFM_CONFIG:
IFLA_BRIDGE_CFM_MEP_CREATE_INSTANCE:
The created MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CREATE_DOMAIN:
The created MEP domain.
The type is u32 (br_cfm_domain).
It must be BR_CFM_PORT.
This means that CFM frames are transmitted and received
directly on the port - untagged. Not in a VLAN.
IFLA_BRIDGE_CFM_MEP_CREATE_DIRECTION:
The created MEP direction.
The type is u32 (br_cfm_mep_direction).
It must be BR_CFM_MEP_DIRECTION_DOWN.
This means that CFM frames are transmitted and received on
the port. Not in the bridge.
IFLA_BRIDGE_CFM_MEP_CREATE_IFINDEX:
The created MEP residence port ifindex.
The type is u32 (ifindex).
IFLA_BRIDGE_CFM_MEP_DELETE_INSTANCE:
The deleted MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CONFIG_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CONFIG_UNICAST_MAC:
The configured MEP unicast MAC address.
The type is 6*u8 (array).
This is used as SMAC in all transmitted CFM frames.
IFLA_BRIDGE_CFM_MEP_CONFIG_MDLEVEL:
The configured MEP unicast MD level.
The type is u32.
It must be in the range 1-7.
No CFM frames are passing through this MEP on lower levels.
IFLA_BRIDGE_CFM_MEP_CONFIG_MEPID:
The configured MEP ID.
The type is u32.
It must be in the range 0-0x1FFF.
This MEP ID is inserted in any transmitted CCM frame.
IFLA_BRIDGE_CFM_CC_CONFIG_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_CONFIG_ENABLE:
The Continuity Check (CC) functionality is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL:
The CC expected receive interval of CCM frames.
The type is u32 (br_cfm_ccm_interval).
This is also the transmission interval of CCM frames when enabled.
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_MAID:
The CC expected receive MAID in CCM frames.
The type is CFM_MAID_LENGTH*u8.
This is MAID is also inserted in transmitted CCM frames.
IFLA_BRIDGE_CFM_CC_PEER_MEP_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_PEER_MEPID:
The CC Peer MEP ID added.
The type is u32.
When a Peer MEP ID is added and CC is enabled it is expected to
receive CCM frames from that Peer MEP.
IFLA_BRIDGE_CFM_CC_RDI_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_RDI_RDI:
The RDI that is inserted in transmitted CCM PDU.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_CCM_TX_DMAC:
The transmitted CCM frame destination MAC address.
The type is 6*u8 (array).
This is used as DMAC in all transmitted CFM frames.
IFLA_BRIDGE_CFM_CC_CCM_TX_SEQ_NO_UPDATE:
The transmitted CCM frame update (increment) of sequence
number is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_PERIOD:
The period of time where CCM frame are transmitted.
The type is u32.
The time is given in seconds. SETLINK IFLA_BRIDGE_CFM_CC_CCM_TX
must be done before timeout to keep transmission alive.
When period is zero any ongoing CCM frame transmission
will be stopped.
IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV:
The transmitted CCM frame update with Interface Status TLV
is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV_VALUE:
The transmitted Interface Status TLV value field.
The type is u8.
IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV:
The transmitted CCM frame update with Port Status TLV is enabled
or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV_VALUE:
The transmitted Port Status TLV value field.
The type is u8.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is the implementation of CFM netlink configuration
set information interface.
Add new nested netlink attributes. These attributes are used by the
user space to create/delete/configure CFM instances.
SETLINK:
IFLA_BRIDGE_CFM:
Indicate that the following attributes are CFM.
IFLA_BRIDGE_CFM_MEP_CREATE:
This indicate that a MEP instance must be created.
IFLA_BRIDGE_CFM_MEP_DELETE:
This indicate that a MEP instance must be deleted.
IFLA_BRIDGE_CFM_MEP_CONFIG:
This indicate that a MEP instance must be configured.
IFLA_BRIDGE_CFM_CC_CONFIG:
This indicate that a MEP instance Continuity Check (CC)
functionality must be configured.
IFLA_BRIDGE_CFM_CC_PEER_MEP_ADD:
This indicate that a CC Peer MEP must be added.
IFLA_BRIDGE_CFM_CC_PEER_MEP_REMOVE:
This indicate that a CC Peer MEP must be removed.
IFLA_BRIDGE_CFM_CC_CCM_TX:
This indicate that the CC transmitted CCM PDU must be configured.
IFLA_BRIDGE_CFM_CC_RDI:
This indicate that the CC transmitted CCM PDU RDI must be
configured.
CFM nested attribute has the following attributes in next level.
SETLINK RTEXT_FILTER_CFM_CONFIG:
IFLA_BRIDGE_CFM_MEP_CREATE_INSTANCE:
The created MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CREATE_DOMAIN:
The created MEP domain.
The type is u32 (br_cfm_domain).
It must be BR_CFM_PORT.
This means that CFM frames are transmitted and received
directly on the port - untagged. Not in a VLAN.
IFLA_BRIDGE_CFM_MEP_CREATE_DIRECTION:
The created MEP direction.
The type is u32 (br_cfm_mep_direction).
It must be BR_CFM_MEP_DIRECTION_DOWN.
This means that CFM frames are transmitted and received on
the port. Not in the bridge.
IFLA_BRIDGE_CFM_MEP_CREATE_IFINDEX:
The created MEP residence port ifindex.
The type is u32 (ifindex).
IFLA_BRIDGE_CFM_MEP_DELETE_INSTANCE:
The deleted MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CONFIG_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_MEP_CONFIG_UNICAST_MAC:
The configured MEP unicast MAC address.
The type is 6*u8 (array).
This is used as SMAC in all transmitted CFM frames.
IFLA_BRIDGE_CFM_MEP_CONFIG_MDLEVEL:
The configured MEP unicast MD level.
The type is u32.
It must be in the range 1-7.
No CFM frames are passing through this MEP on lower levels.
IFLA_BRIDGE_CFM_MEP_CONFIG_MEPID:
The configured MEP ID.
The type is u32.
It must be in the range 0-0x1FFF.
This MEP ID is inserted in any transmitted CCM frame.
IFLA_BRIDGE_CFM_CC_CONFIG_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_CONFIG_ENABLE:
The Continuity Check (CC) functionality is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_INTERVAL:
The CC expected receive interval of CCM frames.
The type is u32 (br_cfm_ccm_interval).
This is also the transmission interval of CCM frames when enabled.
IFLA_BRIDGE_CFM_CC_CONFIG_EXP_MAID:
The CC expected receive MAID in CCM frames.
The type is CFM_MAID_LENGTH*u8.
This is MAID is also inserted in transmitted CCM frames.
IFLA_BRIDGE_CFM_CC_PEER_MEP_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_PEER_MEPID:
The CC Peer MEP ID added.
The type is u32.
When a Peer MEP ID is added and CC is enabled it is expected to
receive CCM frames from that Peer MEP.
IFLA_BRIDGE_CFM_CC_RDI_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_RDI_RDI:
The RDI that is inserted in transmitted CCM PDU.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_INSTANCE:
The configured MEP instance number.
The type is u32.
IFLA_BRIDGE_CFM_CC_CCM_TX_DMAC:
The transmitted CCM frame destination MAC address.
The type is 6*u8 (array).
This is used as DMAC in all transmitted CFM frames.
IFLA_BRIDGE_CFM_CC_CCM_TX_SEQ_NO_UPDATE:
The transmitted CCM frame update (increment) of sequence
number is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_PERIOD:
The period of time where CCM frame are transmitted.
The type is u32.
The time is given in seconds. SETLINK IFLA_BRIDGE_CFM_CC_CCM_TX
must be done before timeout to keep transmission alive.
When period is zero any ongoing CCM frame transmission
will be stopped.
IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV:
The transmitted CCM frame update with Interface Status TLV
is enabled or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_IF_TLV_VALUE:
The transmitted Interface Status TLV value field.
The type is u8.
IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV:
The transmitted CCM frame update with Port Status TLV is enabled
or disabled.
The type is u32 (bool).
IFLA_BRIDGE_CFM_CC_CCM_TX_PORT_TLV_VALUE:
The transmitted Port Status TLV value field.
The type is u8.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is the third commit of the implementation of the CFM protocol
according to 802.1Q section 12.14.
Functionality is extended with CCM frame reception.
The MEP instance now contains CCM based status information.
Most important is the CCM defect status indicating if correct
CCM frames are received with the expected interval.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is the second commit of the implementation of the CFM protocol
according to 802.1Q section 12.14.
Functionality is extended with CCM frame transmission.
Interface is extended with these functions:
br_cfm_cc_rdi_set()
br_cfm_cc_ccm_tx()
br_cfm_cc_config_set()
A MEP Continuity Check feature can be configured by
br_cfm_cc_config_set()
The Continuity Check parameters can be configured to be used when
transmitting CCM.
A MEP can be configured to start or stop transmission of CCM frames by
br_cfm_cc_ccm_tx()
The CCM will be transmitted for a selected period in seconds.
Must call this function before timeout to keep transmission alive.
A MEP transmitting CCM can be configured with inserted RDI in PDU by
br_cfm_cc_rdi_set()
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is the first commit of the implementation of the CFM protocol
according to 802.1Q section 12.14.
It contains MEP instance create, delete and configuration.
Connectivity Fault Management (CFM) comprises capabilities for
detecting, verifying, and isolating connectivity failures in
Virtual Bridged Networks. These capabilities can be used in
networks operated by multiple independent organizations, each
with restricted management access to each others equipment.
CFM functions are partitioned as follows:
- Path discovery
- Fault detection
- Fault verification and isolation
- Fault notification
- Fault recovery
Interface consists of these functions:
br_cfm_mep_create()
br_cfm_mep_delete()
br_cfm_mep_config_set()
br_cfm_cc_config_set()
br_cfm_cc_peer_mep_add()
br_cfm_cc_peer_mep_remove()
A MEP instance is created by br_cfm_mep_create()
-It is the Maintenance association End Point
described in 802.1Q section 19.2.
-It is created on a specific level (1-7) and is assuring
that no CFM frames are passing through this MEP on lower levels.
-It initiates and validates CFM frames on its level.
-It can only exist on a port that is related to a bridge.
-Attributes given cannot be changed until the instance is
deleted.
A MEP instance can be deleted by br_cfm_mep_delete().
A created MEP instance has attributes that can be
configured by br_cfm_mep_config_set().
A MEP Continuity Check feature can be configured by
br_cfm_cc_config_set()
The Continuity Check Receiver state machine can be
enabled and disabled.
According to 802.1Q section 19.2.8
A MEP can have Peer MEPs added and removed by
br_cfm_cc_peer_mep_add() and br_cfm_cc_peer_mep_remove()
The Continuity Check feature can maintain connectivity
status on each added Peer MEP.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This EtherType is used by all CFM protocal frames transmitted
according to 802.1Q section 12.14.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This makes it possible to include or exclude the CFM
protocol according to 802.1Q section 12.14.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch extends the processing of frames in the bridge. Currently MRP
frames needs special processing and the current implementation doesn't
allow a nice way to process different frame types. Therefore try to
improve this by adding a list that contains frame types that need
special processing. This list is iterated for each input frame and if
there is a match based on frame type then these functions will be called
and decide what to do with the frame. It can process the frame then the
bridge doesn't need to do anything or don't process so then the bridge
will do normal forwarding.
Signed-off-by: Henrik Bjoernlund <henrik.bjoernlund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
