skb_tx_timestamp() does not report software time stamp
if SKBTX_IN_PROGRESS is set. According to timestamping.txt
software time stamps are a fallback and should not be
generated if hardware time stamp is provided.
Move call to skb_tx_timestamp() after setting
SKBTX_IN_PROGRESS.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ptp_tx_skb is always set before work is scheduled,
work is cancelled before ptp_tx_skb is set to NULL.
PTP work cannot ever see ptp_tx_skb set to NULL.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit da1e2046e5, the flow for enabling/disabling an Si errata
workaround (e1000_lv_jumbo_workaround_ich8lan) was changed to fix a problem
with iAMT connections dropping on interface down with jumbo frames set.
Part of this change was to move the function call disabling the workaround
to e1000e_down() from the e1000_setup_rctl() function. The mechanic for
disabling of this workaround involves writing several MAC and PHY registers
back to hardware defaults.
After this commit, when the driver is loaded with the cable out, the PHY
registers are not programmed with the correct default values. This causes
the device to be capable of transmitting packets, but is unable to recieve
them until this workaround is called.
The flow of e1000e's open code relies upon calling the above workaround to
expicitly program these registers either with jumbo frame appropriate settings
or h/w defaults on 82579 and newer hardware.
Fix this issue by adding logic to e1000_setup_rctl() that not only calls
e1000_lv_jumbo_workaround_ich8lan() when jumbo frames are set, to enable the
workaround, but also calls this function to explicitly disable the workaround
in the case that jumbo frames are not set.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull libata updates from Tejun Heo:
"A lot of activities on libata side this time.
- A lot of changes around ahci. Various embedded platforms are
implementing ahci controllers. Some were built atop ahci_platform,
others were doing their own things. Hans made some structural
changes to libahci and librarized ahci_platform so that ahci
platform drivers can share more common code. A couple platform
drivers are added on top of that and several are added to replace
older drivers which were doing their own things (older ones are
scheduled to be removed).
- Dan finishes the patchset to make libata PM operations
asynchronous. Combined with one patch being routed through scsi,
this should speed resume measurably.
- Various fixes and cleanups from Bartlomiej and others"
* 'for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (61 commits)
ata: fix Marvell SATA driver dependencies
ata: fix ARASAN CompactFlash PATA driver dependencies
ata: remove superfluous casts
ata: sata_highbank: remove superfluous cast
ata: fix Calxeda Highbank SATA driver dependencies
ata: fix R-Car SATA driver dependencies
ARM: davinci: da850: update SATA AHCI support
ata: add new-style AHCI platform driver for DaVinci DA850 AHCI controller
ata: move library code from ahci_platform.c to libahci_platform.c
ata: ahci_platform: fix ahci_platform_data->suspend method handling
libata: remove unused ata_sas_port_async_resume() stub
libata.h: add stub for ata_sas_port_resume
libata: async resume
libata, libsas: kill pm_result and related cleanup
ata: Fix compiler warning with APM X-Gene host controller driver
arm64: Add APM X-Gene SoC AHCI SATA host controller DTS entries
ata: Add APM X-Gene SoC AHCI SATA host controller driver
Documentation: Add documentation for the APM X-Gene SoC SATA host controller DTS binding
arm64: Add APM X-Gene SoC 15Gbps Multi-purpose PHY DTS entries
ata: ahci_sunxi: fix code formatting
...
Pull workqueue changes from Tejun Heo:
"PREPARE_[DELAYED_]WORK() were used to change the work function of work
items without fully reinitializing it; however, this makes workqueue
consider the work item as a different one from before and allows the
work item to start executing before the previous instance is finished
which can lead to extremely subtle issues which are painful to debug.
The interface has never been popular. This pull request contains
patches to remove existing usages and kill the interface. As one of
the changes was routed during the last devel cycle and another
depended on a pending change in nvme, for-3.15 contains a couple merge
commits.
In addition, interfaces which were deprecated quite a while ago -
__cancel_delayed_work() and WQ_NON_REENTRANT - are removed too"
* 'for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: remove deprecated WQ_NON_REENTRANT
workqueue: Spelling s/instensive/intensive/
workqueue: remove PREPARE_[DELAYED_]WORK()
staging/fwserial: don't use PREPARE_WORK
afs: don't use PREPARE_WORK
nvme: don't use PREPARE_WORK
usb: don't use PREPARE_DELAYED_WORK
floppy: don't use PREPARE_[DELAYED_]WORK
ps3-vuart: don't use PREPARE_WORK
wireless/rt2x00: don't use PREPARE_WORK in rt2800usb.c
workqueue: Remove deprecated __cancel_delayed_work()
Pull percpu changes from Tejun Heo:
"The percpu allocation is now popular enough for the extremely naive
range allocator to cause scalability issues.
The existing allocator linearly scanned the allocation map on both
alloc and free without making use of hint or anything. Al
reimplemented the range allocator so that it can use binary search
instead of linear scan during free and alloc path uses simple hinting
to avoid scanning in common cases. Combined, the new allocator
resolves the scalability issue percpu allocator was showing during
container benchmark workload"
* 'for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: renew the max_contig if we merge the head and previous block
percpu: allocation size should be even
percpu: speed alloc_pcpu_area() up
percpu: store offsets instead of lengths in ->map[]
perpcu: fold pcpu_split_block() into the only caller
- PCI I/O space extended to 16M (in preparation of PCIe support patches)
- Dropping ZONE_DMA32 in favour of ZONE_DMA (we only need one for the
time being), together with swiotlb late initialisation to correctly
setup the bounce buffer
- DMA API cache maintenance support (not all ARMv8 platforms have
hardware cache coherency)
- Crypto extensions advertising via ELF_HWCAP2 for compat user space
- Perf support for dwarf unwinding in compat mode
- asm/tlb.h converted to the generic mmu_gather code
- asm-generic rwsem implementation
- Code clean-up
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=8+cB
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull ARM64 updates from Catalin Marinas:
- KGDB support for arm64
- PCI I/O space extended to 16M (in preparation of PCIe support
patches)
- Dropping ZONE_DMA32 in favour of ZONE_DMA (we only need one for the
time being), together with swiotlb late initialisation to correctly
setup the bounce buffer
- DMA API cache maintenance support (not all ARMv8 platforms have
hardware cache coherency)
- Crypto extensions advertising via ELF_HWCAP2 for compat user space
- Perf support for dwarf unwinding in compat mode
- asm/tlb.h converted to the generic mmu_gather code
- asm-generic rwsem implementation
- Code clean-up
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (42 commits)
arm64: Remove pgprot_dmacoherent()
arm64: Support DMA_ATTR_WRITE_COMBINE
arm64: Implement custom mmap functions for dma mapping
arm64: Fix __range_ok macro
arm64: Fix duplicated Kconfig entries
arm64: mm: Route pmd thp functions through pte equivalents
arm64: rwsem: use asm-generic rwsem implementation
asm-generic: rwsem: de-PPCify rwsem.h
arm64: enable generic CPU feature modalias matching for this architecture
arm64: smp: make local symbol static
arm64: debug: make local symbols static
ARM64: perf: support dwarf unwinding in compat mode
ARM64: perf: add support for frame pointer unwinding in compat mode
ARM64: perf: add support for perf registers API
arm64: Add boot time configuration of Intermediate Physical Address size
arm64: Do not synchronise I and D caches for special ptes
arm64: Make DMA coherent and strongly ordered mappings not executable
arm64: barriers: add dmb barrier
arm64: topology: Implement basic CPU topology support
arm64: advertise ARMv8 extensions to 32-bit compat ELF binaries
...
Pull s390 updates from Martin Schwidefsky:
"There are two memory management related changes, the CMMA support for
KVM to avoid swap-in of freed pages and the split page table lock for
the PMD level. These two come with common code changes in mm/.
A fix for the long standing theoretical TLB flush problem, this one
comes with a common code change in kernel/sched/.
Another set of changes is Heikos uaccess work, included is the initial
set of patches with more to come.
And fixes and cleanups as usual"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (36 commits)
s390/con3270: optionally disable auto update
s390/mm: remove unecessary parameter from pgste_ipte_notify
s390/mm: remove unnecessary parameter from gmap_do_ipte_notify
s390/mm: fixing comment so that parameter name match
s390/smp: limit number of cpus in possible cpu mask
hypfs: Add clarification for "weight_min" attribute
s390: update defconfigs
s390/ptrace: add support for PTRACE_SINGLEBLOCK
s390/perf: make print_debug_cf() static
s390/topology: Remove call to update_cpu_masks()
s390/compat: remove compat exec domain
s390: select CONFIG_TTY for use of tty in unconditional keyboard driver
s390/appldata_os: fix cpu array size calculation
s390/checksum: remove memset() within csum_partial_copy_from_user()
s390/uaccess: remove copy_from_user_real()
s390/sclp_early: Return correct HSA block count also for zero
s390: add some drivers/subsystems to the MAINTAINERS file
s390: improve debug feature usage
s390/airq: add support for irq ranges
s390/mm: enable split page table lock for PMD level
...
Pull s390 compat wrapper rework from Heiko Carstens:
"S390 compat system call wrapper simplification work.
The intention of this work is to get rid of all hand written assembly
compat system call wrappers on s390, which perform proper sign or zero
extension, or pointer conversion of compat system call parameters.
Instead all of this should be done with C code eg by using Al's
COMPAT_SYSCALL_DEFINEx() macro.
Therefore all common code and s390 specific compat system calls have
been converted to the COMPAT_SYSCALL_DEFINEx() macro.
In order to generate correct code all compat system calls may only
have eg compat_ulong_t parameters, but no unsigned long parameters.
Those patches which change parameter types from unsigned long to
compat_ulong_t parameters are separate in this series, but shouldn't
cause any harm.
The only compat system calls which intentionally have 64 bit
parameters (preadv64 and pwritev64) in support of the x86/32 ABI
haven't been changed, but are now only available if an architecture
defines __ARCH_WANT_COMPAT_SYS_PREADV64/PWRITEV64.
System calls which do not have a compat variant but still need proper
zero extension on s390, like eg "long sys_brk(unsigned long brk)" will
get a proper wrapper function with the new s390 specific
COMPAT_SYSCALL_WRAPx() macro:
COMPAT_SYSCALL_WRAP1(brk, unsigned long, brk);
which generates the following code (simplified):
asmlinkage long sys_brk(unsigned long brk);
asmlinkage long compat_sys_brk(long brk)
{
return sys_brk((u32)brk);
}
Given that the C file which contains all the COMPAT_SYSCALL_WRAP lines
includes both linux/syscall.h and linux/compat.h, it will generate
build errors, if the declaration of sys_brk() doesn't match, or if
there exists a non-matching compat_sys_brk() declaration.
In addition this will intentionally result in a link error if
somewhere else a compat_sys_brk() function exists, which probably
should have been used instead. Two more BUILD_BUG_ONs make sure the
size and type of each compat syscall parameter can be handled
correctly with the s390 specific macros.
I converted the compat system calls step by step to verify the
generated code is correct and matches the previous code. In fact it
did not always match, however that was always a bug in the hand
written asm code.
In result we get less code, less bugs, and much more sanity checking"
* 'compat' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (44 commits)
s390/compat: add copyright statement
compat: include linux/unistd.h within linux/compat.h
s390/compat: get rid of compat wrapper assembly code
s390/compat: build error for large compat syscall args
mm/compat: convert to COMPAT_SYSCALL_DEFINE with changing parameter types
kexec/compat: convert to COMPAT_SYSCALL_DEFINE with changing parameter types
net/compat: convert to COMPAT_SYSCALL_DEFINE with changing parameter types
ipc/compat: convert to COMPAT_SYSCALL_DEFINE with changing parameter types
fs/compat: convert to COMPAT_SYSCALL_DEFINE with changing parameter types
ipc/compat: convert to COMPAT_SYSCALL_DEFINE
fs/compat: convert to COMPAT_SYSCALL_DEFINE
security/compat: convert to COMPAT_SYSCALL_DEFINE
mm/compat: convert to COMPAT_SYSCALL_DEFINE
net/compat: convert to COMPAT_SYSCALL_DEFINE
kernel/compat: convert to COMPAT_SYSCALL_DEFINE
fs/compat: optional preadv64/pwrite64 compat system calls
ipc/compat_sys_msgrcv: change msgtyp type from long to compat_long_t
s390/compat: partial parameter conversion within syscall wrappers
s390/compat: automatic zero, sign and pointer conversion of syscalls
s390/compat: add sync_file_range and fallocate compat syscalls
...
Pull x86 LTO changes from Peter Anvin:
"More infrastructure work in preparation for link-time optimization
(LTO). Most of these changes is to make sure symbols accessed from
assembly code are properly marked as visible so the linker doesn't
remove them.
My understanding is that the changes to support LTO are still not
upstream in binutils, but are on the way there. This patchset should
conclude the x86-specific changes, and remaining patches to actually
enable LTO will be fed through the Kbuild tree (other than keeping up
with changes to the x86 code base, of course), although not
necessarily in this merge window"
* 'x86-asmlinkage-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
Kbuild, lto: Handle basic LTO in modpost
Kbuild, lto: Disable LTO for asm-offsets.c
Kbuild, lto: Add a gcc-ld script to let run gcc as ld
Kbuild, lto: add ld-version and ld-ifversion macros
Kbuild, lto: Drop .number postfixes in modpost
Kbuild, lto, workaround: Don't warn for initcall_reference in modpost
lto: Disable LTO for sys_ni
lto: Handle LTO common symbols in module loader
lto, workaround: Add workaround for initcall reordering
lto: Make asmlinkage __visible
x86, lto: Disable LTO for the x86 VDSO
initconst, x86: Fix initconst mistake in ts5500 code
initconst: Fix initconst mistake in dcdbas
asmlinkage: Make trace_hardirqs_on/off_caller visible
asmlinkage, x86: Fix 32bit memcpy for LTO
asmlinkage Make __stack_chk_failed and memcmp visible
asmlinkage: Mark rwsem functions that can be called from assembler asmlinkage
asmlinkage: Make main_extable_sort_needed visible
asmlinkage, mutex: Mark __visible
asmlinkage: Make trace_hardirq visible
...
Conflicts:
drivers/net/xen-netback/netback.c
A bug fix overlapped with changing how the netback SKB control
block is implemented.
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-03-31
Please accept this one last round of general wireless updates for
the 3.15 merge window!
For the Bluetooth bits, Gustavo says:
"Here follow another set of patches to 3.15. This is mostly a bug fix
pull request with the exception of one commit from Marcel which adds
tracking to the current configured LE scan type parameter."
Beyond that, notable bits include some final refactoring of rtl8180
and the addition of the rtl8187se driver, fixes for a number of
problems identified by Dan Carpenter and his static analysis tools,
and a handful of other bits here and there.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While transmit over a at86rf231 device and unloading the module I got:
[ 29.643073] WARNING: CPU: 0 PID: 3 at kernel/workqueue.c:1335 __queue_work+0xb4/0x224()
[ 29.651457] Modules linked in: at86rf230(-) autofs4
[ 29.656612] CPU: 0 PID: 3 Comm: ksoftirqd/0 Tainted: G W 3.14.0-rc6-01602-g902659e-dirty #294
[ 29.666490] [<c00124f0>] (unwind_backtrace) from [<c0010ad0>] (show_stack+0x10/0x14)
[ 29.674628] [<c0010ad0>] (show_stack) from [<c0032c80>] (warn_slowpath_common+0x60/0x80)
[ 29.683116] [<c0032c80>] (warn_slowpath_common) from [<c0032d30>] (warn_slowpath_null+0x18/0x20)
[ 29.692329] [<c0032d30>] (warn_slowpath_null) from [<c0045b08>] (__queue_work+0xb4/0x224)
[ 29.700906] [<c0045b08>] (__queue_work) from [<c0045cc8>] (queue_work_on+0x50/0x78)
[ 29.708944] [<c0045cc8>] (queue_work_on) from [<c05669cc>] (mac802154_tx+0x1e4/0x240)
[ 29.717164] [<c05669cc>] (mac802154_tx) from [<c0471814>] (dev_hard_start_xmit+0x2f0/0x43c)
[ 29.725926] [<c0471814>] (dev_hard_start_xmit) from [<c04878d0>] (sch_direct_xmit+0x64/0x2a0)
[ 29.734867] [<c04878d0>] (sch_direct_xmit) from [<c0487c38>] (__qdisc_run+0x12c/0x18c)
[ 29.743169] [<c0487c38>] (__qdisc_run) from [<c046e1b0>] (net_tx_action+0xe0/0x178)
[ 29.751205] [<c046e1b0>] (net_tx_action) from [<c0036690>] (__do_softirq+0x100/0x264)
[ 29.759420] [<c0036690>] (__do_softirq) from [<c0036818>] (run_ksoftirqd+0x24/0x4c)
[ 29.767453] [<c0036818>] (run_ksoftirqd) from [<c005232c>] (smpboot_thread_fn+0x128/0x13c)
[ 29.776121] [<c005232c>] (smpboot_thread_fn) from [<c004c3fc>] (kthread+0xd0/0xe4)
[ 29.784061] [<c004c3fc>] (kthread) from [<c000da88>] (ret_from_fork+0x14/0x2c)
[ 29.791628] ---[ end trace 3406ff24bd973834 ]---
The problem is there are still interrupts after deregister ieee802154
device. This patch mask all interrupts in the at86rf2xx chips before
deregister the device.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit c15b1ccadb ("ipv6: move DAD and addrconf_verify
processing to workqueue") some counters are now updated in process context
and thus need to disable bh before doing so, otherwise deadlocks can
happen on 32-bit archs. Fabio Estevam noticed this while while mounting
a NFS volume on an ARM board.
As a compensation for missing this I looked after the other *_STATS_BH
and found three other calls which need updating:
1) icmp6_send: ip6_fragment -> icmpv6_send -> icmp6_send (error handling)
2) ip6_push_pending_frames: rawv6_sendmsg -> rawv6_push_pending_frames -> ...
(only in case of icmp protocol with raw sockets in error handling)
3) ping6_v6_sendmsg (error handling)
Fixes: c15b1ccadb ("ipv6: move DAD and addrconf_verify processing to workqueue")
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Though we made sure to acquire a valid MAC for
the netdevice we never actually programmed it
into the hardware.
So if the bootloader did not set the MAC,
network operation would only work if userspace
explicitly asked to transfer the MAC to hardware.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
First off, we don't need to check for non-NULL rt any more, as we are
guaranteed to always get a valid rt6_info. Drop the check.
In case we couldn't allocate an inet_peer for fragmentation information
we currently generate strictly incrementing fragmentation ids for all
destination. This is done to maximize the cycle and avoid collisions.
Those fragmentation ids are very predictable. At least we should try to
mix in the destination address.
While it should make no difference to simply use a PRNG at this point,
secure_ipv6_id ensures that we don't leak information from prandom,
so its internal state could be recoverable.
This fallback function should normally not get used thus this should
not affect performance at all. It is just meant as a safety net.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Main difference between napi_frags_skb() and napi_gro_receive() is that
the later is called while ethernet header was already pulled by the NIC
driver (eth_type_trans() was called before napi_gro_receive())
Jerry Chu in commit 299603e837 ("net-gro: Prepare GRO stack for the
upcoming tunneling support") tried to remove this difference by calling
eth_type_trans() from napi_frags_skb() instead of doing this later from
napi_frags_finish()
Goal was that napi_gro_complete() could call
ptype->callbacks.gro_complete(skb, 0) (offset of first network header =
0)
Also, xxx_gro_receive() handlers all use off = skb_gro_offset(skb) to
point to their own header, for the current skb and ones held in gro_list
Problem is this cleanup work defeated the frag0 optimization:
It turns out the consecutive pskb_may_pull() calls are too expensive.
This patch brings back the frag0 stuff in napi_frags_skb().
As all skb have their mac header in skb head, we no longer need
skb_gro_mac_header()
Reported-by: Michal Schmidt <mschmidt@redhat.com>
Fixes: 299603e837 ("net-gro: Prepare GRO stack for the upcoming tunneling support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Binding might result in a NULL device which is later dereferenced
without checking.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to monitor carrier on/off transitions and detect link
flapping issues:
- new /sys/class/net/X/carrier_changes
- new rtnetlink IFLA_CARRIER_CHANGES (getlink)
Tested:
- grep . /sys/class/net/*/carrier_changes
+ ip link set dev X down/up
+ plug/unplug cable
- updated iproute2: prints IFLA_CARRIER_CHANGES
- iproute2 20121211-2 (debian): unchanged behavior
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue raises when adding policy route, specify a particular
NIC as oif, the policy route did not take effect. The reason is
that fl6.oif is not set and route map failed. From the
tcp_v6_send_response function, if the binding address is linklocal,
fl6.oif is set, but not for global address.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the whole rt6_need_strict as static inline into ip6_route.h,
so that it can be reused
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: document sysfs entries
This patchset attempts to document the basic set of sysfs entries that are
exposed by netdevices in /sys/class/net/<iface>/
I did not go before the pre-git era, so the oldest entries are marked with
the 2.6.12 kernel version and dated of April 2005.
Future patches will document the queues/ and statistics/ directories as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_ADDR_* values are exported in the
/sys/class/net/<iface>/addr_assign_type sysfs attributes, and as such
constitutes an user-space ABI. Move the NET_ADDR_* definitions from
include/linux/netdevice.h to include/uapi/linux/netdevice.h
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sysfs attributes Documentation entries for the basic set of
attributes that are exposed by a network device in
/sys/class/net/<iface>/
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 03bbcb2e7e (iommu/vt-d: add quirk for broken interrupt
remapping on 55XX chipsets) properly disables irq remapping on the
5500/5520 chipsets that don't correctly perform that feature.
However, when I wrote it, I followed the errata sheet linked in that
commit too closely, and explicitly tied the activation of the quirk to
revision 0x13 of the chip, under the assumption that earlier revisions
were not in the field. Recently a system was reported to be suffering
from this remap bug and the quirk hadn't triggered, because the
revision id register read at a lower value that 0x13, so the quirk
test failed improperly. Given this, it seems only prudent to adjust
this quirk so that any revision less than 0x13 has the quirk asserted.
[ tglx: Removed the 0x12 comparison of pci id 3405 as this is covered
by the <= 0x13 check already ]
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1394649873-14913-1-git-send-email-nhorman@tuxdriver.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This device provides QMI and ethernet functionality via a standard CDC
ethernet descriptor. But when driven by cdc_ether, the QMI
functionality is unavailable because only cdc_ether can claim the USB
interface. Thus blacklist the device in cdc_ether and add its IDs to
qmi_wwan, which enables both QMI and ethernet simultaneously.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich says:
====================
bridge: Fix forwarding of 8021AD frames
Bridge has its own way to deterine if the packet is forwardable and it doesn't
support 8021ad tags correctly. Instead just allow bridge to use an
existing is_skb_forwardable() function.
v2: Fix missing hunk in patch 2/2 to make it build.
v3: Fix indent for is_skb_forwardable
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use existing function instead of trying to use our own.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 hyperv change from Ingo Molnar:
"Skip the timer_irq_works() check on hyperv systems"
* 'x86-hyperv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, hyperv: Bypass the timer_irq_works() check
Pull x86 hashing changes from Ingo Molnar:
"Small fixes and cleanups to the librarized arch_fast_hash() methods,
used by the net/openvswitch code"
* 'x86-hash-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, hash: Simplify switch, add __init annotation
x86, hash: Swap arguments passed to crc32_u32()
x86, hash: Fix build failure with older binutils
Pull x86 EFI changes from Ingo Molnar:
"The main changes:
- Add debug code to the dump EFI pagetable - Borislav Petkov
- Make 1:1 runtime mapping robust when booting on machines with lots
of memory - Borislav Petkov
- Move the EFI facilities bits out of 'x86_efi_facility' and into
efi.flags which is the standard architecture independent place to
keep EFI state, by Matt Fleming.
- Add 'EFI mixed mode' support: this allows 64-bit kernels to be
booted from 32-bit firmware. This needs a bootloader that supports
the 'EFI handover protocol'. By Matt Fleming"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
x86, efi: Abstract x86 efi_early calls
x86/efi: Restore 'attr' argument to query_variable_info()
x86/efi: Rip out phys_efi_get_time()
x86/efi: Preserve segment registers in mixed mode
x86/boot: Fix non-EFI build
x86, tools: Fix up compiler warnings
x86/efi: Re-disable interrupts after calling firmware services
x86/boot: Don't overwrite cr4 when enabling PAE
x86/efi: Wire up CONFIG_EFI_MIXED
x86/efi: Add mixed runtime services support
x86/efi: Firmware agnostic handover entry points
x86/efi: Split the boot stub into 32/64 code paths
x86/efi: Add early thunk code to go from 64-bit to 32-bit
x86/efi: Build our own EFI services pointer table
efi: Add separate 32-bit/64-bit definitions
x86/efi: Delete dead code when checking for non-native
x86/mm/pageattr: Always dump the right page table in an oops
x86, tools: Consolidate #ifdef code
x86/boot: Cleanup header.S by removing some #ifdefs
efi: Use NULL instead of 0 for pointer
...
Pull x86 debug cleanup from Ingo Molnar:
"A single trivial cleanup"
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
i386: Remove unneeded test of 'task' in dump_trace() (again)
Pull x86 cpu handling changes from Ingo Molnar:
"Bigger changes:
- Intel CPU hardware-enablement: new vector instructions support
(AVX-512), by Fenghua Yu.
- Support the clflushopt instruction and use it in appropriate
places. clflushopt is similar to clflush but with more relaxed
ordering, by Ross Zwisler.
- MSR accessor cleanups, by Borislav Petkov.
- 'forcepae' boot flag for those who have way too much time to spend
on way too old Pentium-M systems and want to live way too
dangerously, by Chris Bainbridge"
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpu: Add forcepae parameter for booting PAE kernels on PAE-disabled Pentium M
Rename TAINT_UNSAFE_SMP to TAINT_CPU_OUT_OF_SPEC
x86, intel: Make MSR_IA32_MISC_ENABLE bit constants systematic
x86, Intel: Convert to the new bit access MSR accessors
x86, AMD: Convert to the new bit access MSR accessors
x86: Add another set of MSR accessor functions
x86: Use clflushopt in drm_clflush_virt_range
x86: Use clflushopt in drm_clflush_page
x86: Use clflushopt in clflush_cache_range
x86: Add support for the clflushopt instruction
x86, AVX-512: Enable AVX-512 States Context Switch
x86, AVX-512: AVX-512 Feature Detection
Pull x86 build change from Ingo Molnar:
"Explicitly disable x87 FPU instructions, to catch mistaken floating
point use at build time, instead of crashing or misbehaving during run
time"
* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Disable generation of traditional x87 instructions
Pull x86 apic changes from Ingo Molnar:
"An xAPIC CPU hotplug race fix, plus cleanups and minor fixes"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Plug racy xAPIC access of CPU hotplug code
x86/apic: Always define nox2apic and define it as initdata
x86/apic: Remove unused function prototypes
x86/apic: Switch wait_for_init_deassert() to a bool flag
x86/apic: Only use default_wait_for_init_deassert()
Pull x86 acpi numa fix from Ingo Molnar:
"A single NUMA CPU hotplug fix"
* 'x86-acpi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, acpi: Fix bug in associating hot-added CPUs with corresponding NUMA node
Pull scheduler changes from Ingo Molnar:
"Bigger changes:
- sched/idle restructuring: they are WIP preparation for deeper
integration between the scheduler and idle state selection, by
Nicolas Pitre.
- add NUMA scheduling pseudo-interleaving, by Rik van Riel.
- optimize cgroup context switches, by Peter Zijlstra.
- RT scheduling enhancements, by Thomas Gleixner.
The rest is smaller changes, non-urgnt fixes and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (68 commits)
sched: Clean up the task_hot() function
sched: Remove double calculation in fix_small_imbalance()
sched: Fix broken setscheduler()
sparc64, sched: Remove unused sparc64_multi_core
sched: Remove unused mc_capable() and smt_capable()
sched/numa: Move task_numa_free() to __put_task_struct()
sched/fair: Fix endless loop in idle_balance()
sched/core: Fix endless loop in pick_next_task()
sched/fair: Push down check for high priority class task into idle_balance()
sched/rt: Fix picking RT and DL tasks from empty queue
trace: Replace hardcoding of 19 with MAX_NICE
sched: Guarantee task priority in pick_next_task()
sched/idle: Remove stale old file
sched: Put rq's sched_avg under CONFIG_FAIR_GROUP_SCHED
cpuidle/arm64: Remove redundant cpuidle_idle_call()
cpuidle/powernv: Remove redundant cpuidle_idle_call()
sched, nohz: Exclude isolated cores from load balancing
sched: Fix select_task_rq_fair() description comments
workqueue: Replace hardcoding of -20 and 19 with MIN_NICE and MAX_NICE
sys: Replace hardcoding of -20 and 19 with MIN_NICE and MAX_NICE
...
Pull perf changes from Ingo Molnar:
"Main changes:
Kernel side changes:
- Add SNB/IVB/HSW client uncore memory controller support (Stephane
Eranian)
- Fix various x86/P4 PMU driver bugs (Don Zickus)
Tooling, user visible changes:
- Add several futex 'perf bench' microbenchmarks (Davidlohr Bueso)
- Speed up thread map generation (Don Zickus)
- Introduce 'perf kvm --list-cmds' command line option for use by
scripts (Ramkumar Ramachandra)
- Print the evsel name in the annotate stdio output, prep to fix
support outputting annotation for multiple events, not just for the
first one (Arnaldo Carvalho de Melo)
- Allow setting preferred callchain method in .perfconfig (Jiri Olsa)
- Show in what binaries/modules 'perf probe's are set (Masami
Hiramatsu)
- Support distro-style debuginfo for uprobe in 'perf probe' (Masami
Hiramatsu)
Tooling, internal changes and fixes:
- Use tid in mmap/mmap2 events to find maps (Don Zickus)
- Record the reason for filtering an address_location (Namhyung Kim)
- Apply all filters to an addr_location (Namhyung Kim)
- Merge al->filtered with hist_entry->filtered in report/hists
(Namhyung Kim)
- Fix memory leak when synthesizing thread records (Namhyung Kim)
- Use ui__has_annotation() in 'report' (Namhyung Kim)
- hists browser refactorings to reuse code accross UIs (Namhyung Kim)
- Add support for the new DWARF unwinder library in elfutils (Jiri
Olsa)
- Fix build race in the generation of bison files (Jiri Olsa)
- Further streamline the feature detection display, trimming it a bit
to show just the libraries detected, using VF=1 gets a more verbose
output, showing the less interesting feature checks as well (Jiri
Olsa).
- Check compatible symtab type before loading dso (Namhyung Kim)
- Check return value of filename__read_debuglink() (Stephane Eranian)
- Move some hashing and fs related code from tools/perf/util/ to
tools/lib/ so that it can be used by more tools/ living utilities
(Borislav Petkov)
- Prepare DWARF unwinding code for using an elfutils alternative
unwinding library (Jiri Olsa)
- Fix DWARF unwind max_stack processing (Jiri Olsa)
- Add dwarf unwind 'perf test' entry (Jiri Olsa)
- 'perf probe' improvements including memory leak fixes, sharing the
intlist class with other tools, uprobes/kprobes code sharing and
use of ref_reloc_sym (Masami Hiramatsu)
- Shorten sample symbol resolving by adding cpumode to struct
addr_location (Arnaldo Carvalho de Melo)
- Fix synthesizing mmaps for threads (Don Zickus)
- Fix invalid output on event group stdio report (Namhyung Kim)
- Fixup header alignment in 'perf sched latency' output (Ramkumar
Ramachandra)
- Fix off-by-one error in 'perf timechart record' argv handling
(Ramkumar Ramachandra)
Tooling, cleanups:
- Remove unused thread__find_map function (Jiri Olsa)
- Remove unused simple_strtoul() function (Ramkumar Ramachandra)
Tooling, documentation updates:
- Update function names in debug messages (Ramkumar Ramachandra)
- Update some code references in design.txt (Ramkumar Ramachandra)
- Clarify load-latency information in the 'perf mem' docs (Andi
Kleen)
- Clarify x86 register naming in 'perf probe' docs (Andi Kleen)"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (96 commits)
perf tools: Remove unused simple_strtoul() function
perf tools: Update some code references in design.txt
perf evsel: Update function names in debug messages
perf tools: Remove thread__find_map function
perf annotate: Print the evsel name in the stdio output
perf report: Use ui__has_annotation()
perf tools: Fix memory leak when synthesizing thread records
perf tools: Use tid in mmap/mmap2 events to find maps
perf report: Merge al->filtered with hist_entry->filtered
perf symbols: Apply all filters to an addr_location
perf symbols: Record the reason for filtering an address_location
perf sched: Fixup header alignment in 'latency' output
perf timechart: Fix off-by-one error in 'record' argv handling
perf machine: Factor machine__find_thread to take tid argument
perf tools: Speed up thread map generation
perf kvm: introduce --list-cmds for use by scripts
perf ui hists: Pass evsel to hpp->header/width functions explicitly
perf symbols: Introduce thread__find_cpumode_addr_location
perf session: Change header.misc dump from decimal to hex
perf ui/tui: Reuse generic __hpp__fmt() code
...
Pull hweight type fix from Ingo Molnar:
"This lone commit makes sure that __const_hweight8() is unsigned, which
addresses a build warning if code is built with -Wsign-compare.
I hope the type cast in this cleanup is fine - another option would be
to eliminate the double unary negation and use a construct with more
obvious integer type characteristics, along the lines of:
((w) & (1ULL << 1) ? 1U : 0U)
or so"
* 'core-types-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
bitops: Fix signedness of compile-time hweight implementations
Pull RCU updates from Ingo Molnar:
"Main changes:
- Torture-test changes, including refactoring of rcutorture and
introduction of a vestigial locktorture.
- Real-time latency fixes.
- Documentation updates.
- Miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (77 commits)
rcu: Provide grace-period piggybacking API
rcu: Ensure kernel/rcu/rcu.h can be sourced/used stand-alone
rcu: Fix sparse warning for rcu_expedited from kernel/ksysfs.c
notifier: Substitute rcu_access_pointer() for rcu_dereference_raw()
Documentation/memory-barriers.txt: Clarify release/acquire ordering
rcutorture: Save kvm.sh output to log
rcutorture: Add a lock_busted to test the test
rcutorture: Place kvm-test-1-run.sh output into res directory
rcutorture: Rename TREE_RCU-Kconfig.txt
locktorture: Add kvm-recheck.sh plug-in for locktorture
rcutorture: Gracefully handle NULL cleanup hooks
locktorture: Add vestigial locktorture configuration
rcutorture: Introduce "rcu" directory level underneath configs
rcutorture: Rename kvm-test-1-rcu.sh
rcutorture: Remove RCU dependencies from ver_functions.sh API
rcutorture: Create CFcommon file for common Kconfig parameters
rcutorture: Create config files for scripted test-the-test testing
rcutorture: Add an rcu_busted to test the test
locktorture: Add a lock-torture kernel module
rcutorture: Abstract kvm-recheck.sh
...
Pull core locking updates from Ingo Molnar:
"The biggest change is the MCS spinlock generalization changes from Tim
Chen, Peter Zijlstra, Jason Low et al. There's also lockdep
fixes/enhancements from Oleg Nesterov, in particular a false negative
fix related to lockdep_set_novalidate_class() usage"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
locking/mutex: Fix debug checks
locking/mutexes: Add extra reschedule point
locking/mutexes: Introduce cancelable MCS lock for adaptive spinning
locking/mutexes: Unlock the mutex without the wait_lock
locking/mutexes: Modify the way optimistic spinners are queued
locking/mutexes: Return false if task need_resched() in mutex_can_spin_on_owner()
locking: Move mcs_spinlock.h into kernel/locking/
m68k: Skip futex_atomic_cmpxchg_inatomic() test
futex: Allow architectures to skip futex_atomic_cmpxchg_inatomic() test
Revert "sched/wait: Suppress Sparse 'variable shadowing' warning"
lockdep: Change lockdep_set_novalidate_class() to use _and_name
lockdep: Change mark_held_locks() to check hlock->check instead of lockdep_no_validate
lockdep: Don't create the wrong dependency on hlock->check == 0
lockdep: Make held_lock->check and "int check" argument bool
locking/mcs: Allow architecture specific asm files to be used for contended case
locking/mcs: Order the header files in Kbuild of each architecture in alphabetical order
sched/wait: Suppress Sparse 'variable shadowing' warning
hung_task/Documentation: Fix hung_task_warnings description
locking/mcs: Allow architectures to hook in to contended paths
locking/mcs: Micro-optimize the MCS code, add extra comments
...
If allocation of io_dmabuf fails, rtl8187_probe() calls usb_put_dev(udev)
while usb_get_dev(udev) is not called yet. As a result refcnt is decremented
incorrectly and usb_dev can be used after memory deallocation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rtl8180/rtl8185/rtl8187se the register space is represented
using packed structure type. Register are thus accessed using a
pointer of this type.
All registers are packed toghether, and only small gaps are present.
However Rtl8187se has also some "sparse" registers, very far from
the "main register block".
It could be possible to access them by simply declare huge reserved
blocks inside the register struct (and this causes NO memory waste).
However, for various reasons, access to those "far" registers is
done with special dedicated macros, without declaring them in the
register struct.
This is done in an intricate manner, that makes code less readable
and caused static analisys tool to produce warnings.
This patch keeps the "macro" mechanism, but it changes its
implementation in a simplier and more straightforward way.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
