The Internet Assigned Numbers Authority (IANA) has recently assigned
a protocol number value of 143 for Ethernet [1].
Before this assignment, encapsulation mechanisms such as Segment Routing
used the IPv6-NoNxt protocol number (59) to indicate that the encapsulated
payload is an Ethernet frame.
In this patch, we add the definition of the Ethernet protocol number to the
kernel headers and update the SRv6 L2 tunnels to use it.
[1] https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml
Signed-off-by: Paolo Lungaroni <paolo.lungaroni@cnit.it>
Reviewed-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Acked-by: Ahmed Abdelsalam <ahmed.abdelsalam@gssi.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rafał found an issue that for non-Ethernet interface, if we down and up
frequently, the memory will be consumed slowly.
The reason is we add allnodes/allrouters addressed in multicast list in
ipv6_add_dev(). When link down, we call ipv6_mc_down(), store all multicast
addresses via mld_add_delrec(). But when link up, we don't call ipv6_mc_up()
for non-Ethernet interface to remove the addresses. This makes idev->mc_tomb
getting bigger and bigger. The call stack looks like:
addrconf_notify(NETDEV_REGISTER)
ipv6_add_dev
ipv6_dev_mc_inc(ff01::1)
ipv6_dev_mc_inc(ff02::1)
ipv6_dev_mc_inc(ff02::2)
addrconf_notify(NETDEV_UP)
addrconf_dev_config
/* Alas, we support only Ethernet autoconfiguration. */
return;
addrconf_notify(NETDEV_DOWN)
addrconf_ifdown
ipv6_mc_down
igmp6_group_dropped(ff02::2)
mld_add_delrec(ff02::2)
igmp6_group_dropped(ff02::1)
igmp6_group_dropped(ff01::1)
After investigating, I can't found a rule to disable multicast on
non-Ethernet interface. In RFC2460, the link could be Ethernet, PPP, ATM,
tunnels, etc. In IPv4, it doesn't check the dev type when calls ip_mc_up()
in inetdev_event(). Even for IPv6, we don't check the dev type and call
ipv6_add_dev(), ipv6_dev_mc_inc() after register device.
So I think it's OK to fix this memory consumer by calling ipv6_mc_up() for
non-Ethernet interface.
v2: Also check IFF_MULTICAST flag to make sure the interface supports
multicast
Reported-by: Rafał Miłecki <zajec5@gmail.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Fixes: 74235a25c6 ("[IPV6] addrconf: Fix IPv6 on tuntap tunnels")
Fixes: 1666d49e1d ("mld: do not remove mld souce list info when set link down")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we modify the peer route and changed it to a new one, we should
remove the old route first. Before the fix:
+ ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::2 proto kernel metric 256 pref medium
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::2 proto kernel metric 256 pref medium
After the fix:
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::3
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 256 pref medium
2001:db8::3 proto kernel metric 256 pref medium
This patch depend on the previous patch "net/ipv6: need update peer route
when modify metric" to update new peer route after delete old one.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we modify the route metric, the peer address's route need also
be updated. Before the fix:
+ ip addr add dev dummy1 2001:db8::1 peer 2001:db8::2 metric 60
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 60 pref medium
2001:db8::2 proto kernel metric 60 pref medium
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 61 pref medium
2001:db8::2 proto kernel metric 60 pref medium
After the fix:
+ ip addr change dev dummy1 2001:db8::1 peer 2001:db8::2 metric 61
+ ip -6 route show dev dummy1
2001:db8::1 proto kernel metric 61 pref medium
2001:db8::2 proto kernel metric 61 pref medium
Fixes: 8308f3ff17 ("net/ipv6: Add support for specifying metric of connected routes")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we add peer address with metric configured, IPv4 could set the dest
metric correctly, but IPv6 do not. e.g.
]# ip addr add 192.0.2.1 peer 192.0.2.2/32 dev eth1 metric 20
]# ip route show dev eth1
192.0.2.2 proto kernel scope link src 192.0.2.1 metric 20
]# ip addr add 2001:db8::1 peer 2001:db8::2/128 dev eth1 metric 20
]# ip -6 route show dev eth1
2001:db8::1 proto kernel metric 20 pref medium
2001:db8::2 proto kernel metric 256 pref medium
Fix this by using configured metric instead of default one.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: 8308f3ff17 ("net/ipv6: Add support for specifying metric of connected routes")
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variables declared in a switch statement before any case statements
cannot be automatically initialized with compiler instrumentation (as
they are not part of any execution flow). With GCC's proposed automatic
stack variable initialization feature, this triggers a warning (and they
don't get initialized). Clang's automatic stack variable initialization
(via CONFIG_INIT_STACK_ALL=y) doesn't throw a warning, but it also
doesn't initialize such variables[1]. Note that these warnings (or silent
skipping) happen before the dead-store elimination optimization phase,
so even when the automatic initializations are later elided in favor of
direct initializations, the warnings remain.
To avoid these problems, move such variables into the "case" where
they're used or lift them up into the main function body.
net/ipv6/ip6_gre.c: In function ‘ip6gre_err’:
net/ipv6/ip6_gre.c:440:32: warning: statement will never be executed [-Wswitch-unreachable]
440 | struct ipv6_tlv_tnl_enc_lim *tel;
| ^~~
net/ipv6/ip6_tunnel.c: In function ‘ip6_tnl_err’:
net/ipv6/ip6_tunnel.c:520:32: warning: statement will never be executed [-Wswitch-unreachable]
520 | struct ipv6_tlv_tnl_enc_lim *tel;
| ^~~
[1] https://bugs.llvm.org/show_bug.cgi?id=44916
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When splitting an RTA_MULTIPATH request into multiple routes and adding the
second and later components, we must not simply remove NLM_F_REPLACE but
instead replace it by NLM_F_CREATE. Otherwise, it may look like the netlink
message was malformed.
For example,
ip route add 2001:db8::1/128 dev dummy0
ip route change 2001:db8::1/128 nexthop via fe80::30:1 dev dummy0 \
nexthop via fe80::30:2 dev dummy0
results in the following warnings:
[ 1035.057019] IPv6: RTM_NEWROUTE with no NLM_F_CREATE or NLM_F_REPLACE
[ 1035.057517] IPv6: NLM_F_CREATE should be set when creating new route
This patch makes the nlmsg sequence look equivalent for __ip6_ins_rt() to
what it would get if the multipath route had been added in multiple netlink
operations:
ip route add 2001:db8::1/128 dev dummy0
ip route change 2001:db8::1/128 nexthop via fe80::30:1 dev dummy0
ip route append 2001:db8::1/128 nexthop via fe80::30:2 dev dummy0
Fixes: 2759647247 ("ipv6: fix ECMP route replacement")
Signed-off-by: Benjamin Poirier <bpoirier@cumulusnetworks.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 2759647247 ("ipv6: fix ECMP route replacement") it is no
longer possible to replace an ECMP-able route by a non ECMP-able route.
For example,
ip route add 2001:db8::1/128 via fe80::1 dev dummy0
ip route replace 2001:db8::1/128 dev dummy0
does not work as expected.
Tweak the replacement logic so that point 3 in the log of the above commit
becomes:
3. If the new route is not ECMP-able, and no matching non-ECMP-able route
exists, replace matching ECMP-able route (if any) or add the new route.
We can now summarize the entire replace semantics to:
When doing a replace, prefer replacing a matching route of the same
"ECMP-able-ness" as the replace argument. If there is no such candidate,
fallback to the first route found.
Fixes: 2759647247 ("ipv6: fix ECMP route replacement")
Signed-off-by: Benjamin Poirier <bpoirier@cumulusnetworks.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
With ipip, it is possible to create an extra interface explicitly
attached to a given physical interface:
# ip link show tunl0
4: tunl0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ipip 0.0.0.0 brd 0.0.0.0
# ip link add tunl1 type ipip dev eth0
# ip link show tunl1
6: tunl1@eth0: <NOARP> mtu 1480 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ipip 0.0.0.0 brd 0.0.0.0
But it is not possible with ip6tnl:
# ip link show ip6tnl0
5: ip6tnl0@NONE: <NOARP> mtu 1452 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/tunnel6 :: brd ::
# ip link add ip6tnl1 type ip6tnl dev eth0
RTNETLINK answers: File exists
This patch aims to make it possible by adding link comparaison in both
tunnel locate and lookup functions; we also modify mtu calculation when
attached to an interface with a lower mtu.
This permits to make use of x-netns communication by moving the newly
created tunnel in a given netns.
Signed-off-by: William Dauchy <w.dauchy@criteo.com>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a helper function to be called only by network drivers
that wraps calls to icmp[v6]_send in a conntrack transformation, in case
NAT has been used. We don't want to pollute the non-driver path, though,
so we introduce this as a helper to be called by places that actually
make use of this, as suggested by Florian.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_MPTCP=y, CONFIG_MPTCP_IPV6=n, and CONFIG_IPV6=m:
ERROR: "mptcp_handle_ipv6_mapped" [net/ipv6/ipv6.ko] undefined!
This does not happen if CONFIG_MPTCP_IPV6=y, as CONFIG_MPTCP_IPV6
selects CONFIG_IPV6, and thus forces CONFIG_IPV6 builtin.
As exporting a symbol for an empty function would be a bit wasteful, fix
this by providing a dummy version of mptcp_handle_ipv6_mapped() for the
CONFIG_MPTCP_IPV6=n case.
Rename mptcp_handle_ipv6_mapped() to mptcpv6_handle_mapped(), to make it
clear this is a pure-IPV6 function, just like mptcpv6_init().
Fixes: cec37a6e41 ("mptcp: Handle MP_CAPABLE options for outgoing connections")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't deal with syncookie mode yet, the syncookie rx path will create
tcp reqsk, i.e. we get OOB access because we treat tcp reqsk as mptcp reqsk one:
TCP: SYN flooding on port 20002. Sending cookies.
BUG: KASAN: slab-out-of-bounds in subflow_syn_recv_sock+0x451/0x4d0 net/mptcp/subflow.c:191
Read of size 1 at addr ffff8881167bc148 by task syz-executor099/2120
subflow_syn_recv_sock+0x451/0x4d0 net/mptcp/subflow.c:191
tcp_get_cookie_sock+0xcf/0x520 net/ipv4/syncookies.c:209
cookie_v6_check+0x15a5/0x1e90 net/ipv6/syncookies.c:252
tcp_v6_cookie_check net/ipv6/tcp_ipv6.c:1123 [inline]
[..]
Bug can be reproduced via "sysctl net.ipv4.tcp_syncookies=2".
Note that MPTCP should work with syncookies (4th ack would carry needed
state), but it appears better to sort that out in -next so do tcp
fallback for now.
I removed the MPTCP ifdef for tcp_rsk "is_mptcp" member because
if (IS_ENABLED()) is easier to read than "#ifdef IS_ENABLED()/#endif" pair.
Cc: Eric Dumazet <edumazet@google.com>
Fixes: cec37a6e41 ("mptcp: Handle MP_CAPABLE options for outgoing connections")
Reported-by: Christoph Paasch <cpaasch@apple.com>
Tested-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends UDP GRO to support fraglist GRO/GSO
by using the previously introduced infrastructure.
If the feature is enabled, all UDP packets are going to
fraglist GRO (local input and forward).
After validating the csum, we mark ip_summed as
CHECKSUM_UNNECESSARY for fraglist GRO packets to
make sure that the csum is not touched.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hooks to tcp_output.c to add MP_CAPABLE to an outgoing SYN request,
to capture the MP_CAPABLE in the received SYN-ACK, to add MP_CAPABLE to
the final ACK of the three-way handshake.
Use the .sk_rx_dst_set() handler in the subflow proto to capture when the
responding SYN-ACK is received and notify the MPTCP connection layer.
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the infrastructure for MPTCP sockets.
MPTCP sockets open one in-kernel TCP socket per subflow. These subflow
sockets are only managed by the MPTCP socket that owns them and are not
visible from userspace. This commit allows a userspace program to open
an MPTCP socket with:
sock = socket(AF_INET, SOCK_STREAM, IPPROTO_MPTCP);
The resulting socket is simply a wrapper around a single regular TCP
socket, without any of the MPTCP protocol implemented over the wire.
Co-developed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Florian Westphal <fw@strlen.de>
Co-developed-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in the same manner as commit d0f4185160 ("net, ip_tunnel: fix
namespaces move"), fix namespace moving as it was broken since commit
8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnel"), but for
ipv6 this time; there is no reason to keep it for ip6_tunnel.
Fixes: 8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnel")
Signed-off-by: William Dauchy <w.dauchy@criteo.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After LRO/GRO is applied, SRv6 encapsulated packets have
SKB_GSO_IPXIP6 feature flag, and this flag must be removed right after
decapulation procedure.
Currently, SKB_GSO_IPXIP6 flag is not removed on End.D* actions, which
creates inconsistent packet state, that is, a normal TCP/IP packets
have the SKB_GSO_IPXIP6 flag. This behavior can cause unexpected
fallback to GSO on routing to netdevices that do not support
SKB_GSO_IPXIP6. For example, on inter-VRF forwarding, decapsulated
packets separated into small packets by GSO because VRF devices do not
support TSO for packets with SKB_GSO_IPXIP6 flag, and this degrades
forwarding performance.
This patch removes encapsulation related GSO flags from the skb right
after the End.D* action is applied.
Fixes: d7a669dd2f ("ipv6: sr: add helper functions for seg6local")
Signed-off-by: Yuki Taguchi <tagyounit@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2020-01-21
1) Fix packet tx through bpf_redirect() for xfrm and vti
interfaces. From Nicolas Dichtel.
2) Do not confirm neighbor when do pmtu update on a virtual
xfrm interface. From Xu Wang.
3) Support output_mark for offload ESP packets, this was
forgotten when the output_mark was added initially.
From Ulrich Weber.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for moving IPv4 GRE tunnels between namespaces was added in
commit b57708add3 ("gre: add x-netns support"). The respective change
for IPv6 tunnels, commit 22f08069e8 ("ip6gre: add x-netns support")
did not drop NETIF_F_NETNS_LOCAL flag so moving them from one netns to
another is still denied in IPv6 case. Drop NETIF_F_NETNS_LOCAL flag from
ip6gre tunnels to allow moving ip6gre tunnel endpoints between network
namespaces.
Signed-off-by: Niko Kortstrom <niko.kortstrom@nokia.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9b42c1f179 ("xfrm: Extend the output_mark") added output_mark
support but missed ESP offload support.
xfrm_smark_get() is not called within xfrm_input() for packets coming
from esp4_gro_receive() or esp6_gro_receive(). Therefore call
xfrm_smark_get() directly within these functions.
Fixes: 9b42c1f179 ("xfrm: Extend the output_mark to support input direction and masking.")
Signed-off-by: Ulrich Weber <ulrich.weber@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In a similar fashion to previous patch, add "offload" and "trap"
indication to IPv6 routes.
This is done by using two unused bits in 'struct fib6_info' to hold
these indications. Capable drivers are expected to set these when
processing the various in-kernel route notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a straight-forward conversion case for the new function,
iterating over the return value from udp_rcv_segment, which actually is
a wrapper around skb_gso_segment.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With an ebpf program that redirects packets through a vti[6] interface,
the packets are dropped because no dst is attached.
This could also be reproduced with an AF_PACKET socket, with the following
python script (vti1 is an ip_vti interface):
import socket
send_s = socket.socket(socket.AF_PACKET, socket.SOCK_RAW, 0)
# scapy
# p = IP(src='10.100.0.2', dst='10.200.0.1')/ICMP(type='echo-request')
# raw(p)
req = b'E\x00\x00\x1c\x00\x01\x00\x00@\x01e\xb2\nd\x00\x02\n\xc8\x00\x01\x08\x00\xf7\xff\x00\x00\x00\x00'
send_s.sendto(req, ('vti1', 0x800, 0, 0))
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
MPTCP will make use of tcp_send_mss() and tcp_push() when sending
data to specific TCP subflows.
tcp_request_sock_ipvX_ops and ipvX_specific will be referenced
during TCP subflow creation.
Co-developed-by: Peter Krystad <peter.krystad@linux.intel.com>
Signed-off-by: Peter Krystad <peter.krystad@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The argument is always ignored, so remove it.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for userspace to specify a device index to limit the scope
of an entry via the TCP_MD5SIG_EXT setsockopt. The existing __tcpm_pad
is renamed to tcpm_ifindex and the new field is only checked if the new
TCP_MD5SIG_FLAG_IFINDEX is set in tcpm_flags. For now, the device index
must point to an L3 master device (e.g., VRF). The API and error
handling are setup to allow the constraint to be relaxed in the future
to any device index.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add l3index to tcp_md5sig_key to represent the L3 domain of a key, and
add l3index to tcp_md5_do_add and tcp_md5_do_del to fill in the key.
With the key now based on an l3index, add the new parameter to the
lookup functions and consider the l3index when looking for a match.
The l3index comes from the skb when processing ingress packets leveraging
the helpers created for socket lookups, tcp_v4_sdif and inet_iif (and the
v6 variants). When the sdif index is set it means the packet ingressed a
device that is part of an L3 domain and inet_iif points to the VRF device.
For egress, the L3 domain is determined from the socket binding and
sk_bound_dev_if.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original ingress device index is saved to the cb space of the skb
and the cb is moved during tcp processing. Since tcp_v6_inbound_md5_hash
can be called before and after the cb move, pass dif and sdif to it so
the caller can save both prior to the cb move. Both are used by a later
patch.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mlxsw is converted to use the new FIB notifications it is
possible to delete the old ones and use the new replace / append /
delete notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an entire multipath route is deleted, only emit a notification if
it is the first route in the node. Emit a replace notification in case
the last sibling is followed by another route. Otherwise, emit a delete
notification.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the purpose of route offload, when a single route is deleted, it is
only of interest if it is the first route in the node or if it is
sibling to such a route.
In the first case, distinguish between several possibilities:
1. Route is the last route in the node. Emit a delete notification
2. Route is followed by a non-multipath route. Emit a replace
notification for the non-multipath route.
3. Route is followed by a multipath route. Emit a replace notification
for the multipath route.
In the second case, only emit a delete notification to ensure the route
is no longer used as a valid nexthop.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new listener is registered to the FIB notification chain it
receives a dump of all the available routes in the system. Instead, make
sure to only replay the IPv6 routes that are actually used in the data
path and are of any interest to the new listener.
This is done by iterating over all the routing tables in the given
namespace, but from each traversed node only the first route ('leaf') is
notified. Multipath routes are notified in a single notification instead
of one for each nexthop.
Add fib6_rt_dump_tmp() to do that. Later on in the patch set it will be
renamed to fib6_rt_dump() instead of the existing one.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to previous patches, only notify the new multipath
route if it is the first route in the node or if it was appended to such
route.
The type of the notification (replace vs. append) is determined based on
the number of routes added ('nhn') and the number of sibling routes. If
the two do not match, then an append notification should be sent.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the corresponding IPv4 patch, only notify the new route if it
is replacing the currently offloaded one. Meaning, the one pointed to by
'fn->leaf'.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib6_add_rt2node() takes care of adding a single route ('struct
fib6_info') to a FIB node. The route in question should only be notified
in case it is added as the first route in the node (lowest metric) or if
it is added as a sibling route to the first route in the node.
The first criterion can be tested by checking if the route is pointed to
by 'fn->leaf'. The second criterion can be tested by checking the new
'notify_sibling_rt' variable that is set when the route is added as a
sibling to the first route in the node.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
Although vti and vti6 are immune to this problem because they are IFF_NOARP
interfaces, as Guillaume pointed. There is still no sense to confirm neighbour
here.
v5: Update commit description.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When do tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
v5: No Change.
v4: Update commit description
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Fixes: 0dec879f63 ("net: use dst_confirm_neigh for UDP, RAW, ICMP, L2TP")
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Tested-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we do ipv6 gre pmtu update, we will also do neigh confirm currently.
This will cause the neigh cache be refreshed and set to REACHABLE before
xmit.
But if the remote mac address changed, e.g. device is deleted and recreated,
we will not able to notice this and still use the old mac address as the neigh
cache is REACHABLE.
Fix this by disable neigh confirm when do pmtu update
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reported-by: Jianlin Shi <jishi@redhat.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTU update code is supposed to be invoked in response to real
networking events that update the PMTU. In IPv6 PMTU update function
__ip6_rt_update_pmtu() we called dst_confirm_neigh() to update neighbor
confirmed time.
But for tunnel code, it will call pmtu before xmit, like:
- tnl_update_pmtu()
- skb_dst_update_pmtu()
- ip6_rt_update_pmtu()
- __ip6_rt_update_pmtu()
- dst_confirm_neigh()
If the tunnel remote dst mac address changed and we still do the neigh
confirm, we will not be able to update neigh cache and ping6 remote
will failed.
So for this ip_tunnel_xmit() case, _EVEN_ if the MTU is changed, we
should not be invoking dst_confirm_neigh() as we have no evidence
of successful two-way communication at this point.
On the other hand it is also important to keep the neigh reachability fresh
for TCP flows, so we cannot remove this dst_confirm_neigh() call.
To fix the issue, we have to add a new bool parameter for dst_ops.update_pmtu
to choose whether we should do neigh update or not. I will add the parameter
in this patch and set all the callers to true to comply with the previous
way, and fix the tunnel code one by one on later patches.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Suggested-by: David Miller <davem@davemloft.net>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
In commit 4b1373de73 ("net: ipv6: addr: perform strict checks also for
doit handlers") we add strict check for inet6_rtm_getaddr(). But we did
the invalid header values check before checking if NETLINK_F_STRICT_CHK
is set. This may break backwards compatibility if user already set the
ifm->ifa_prefixlen, ifm->ifa_flags, ifm->ifa_scope in their netlink code.
I didn't move the nlmsg_len check because I thought it's a valid check.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: 4b1373de73 ("net: ipv6: addr: perform strict checks also for doit handlers")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
ipv6_stub uses the ip6_dst_lookup function to allow other modules to
perform IPv6 lookups. However, this function skips the XFRM layer
entirely.
All users of ipv6_stub->ip6_dst_lookup use ip_route_output_flow (via the
ip_route_output_key and ip_route_output helpers) for their IPv4 lookups,
which calls xfrm_lookup_route(). This patch fixes this inconsistent
behavior by switching the stub to ip6_dst_lookup_flow, which also calls
xfrm_lookup_route().
This requires some changes in all the callers, as these two functions
take different arguments and have different return types.
Fixes: 5f81bd2e5d ("ipv6: export a stub for IPv6 symbols used by vxlan")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used in the conversion of ipv6_stub to ip6_dst_lookup_flow,
as some modules currently pass a net argument without a socket to
ip6_dst_lookup. This is equivalent to commit 343d60aada ("ipv6: change
ipv6_stub_impl.ipv6_dst_lookup to take net argument").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
