The Lenovo SE10 watchdog is only present on Lenovo ThinkEdge SE10
platforms, which are based on Intel Atom SoCs, and its driver relies on
DMI tables. Hence add dependencies on X86 && DMI, to prevent asking the
user about this driver when configuring a kernel without Intel Atom or
DMI support.
While at it, fix the odd indentation (spaces instead of TABs).
Fixes: 1f6602c8ed ("watchdog: lenovo_se10_wdt: Watchdog driver for Lenovo SE10 platform")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/58005595a05ef803b454b78d3ae9b8ee0675bd5d.1715076440.git.geert+renesas@glider.be
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
On AM62x, the watchdog is pet before the valid window is open. Fix
min_hw_heartbeat and accommodate a 2% + static offset safety margin.
The static offset accounts for max hardware error.
Remove the hack in the driver which shifts the open window boundary,
since it is no longer necessary due to the fix mentioned above.
cc: stable@vger.kernel.org
Fixes: 5527483f8f ("watchdog: rti-wdt: attach to running watchdog during probe")
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240417205700.3947408-1-jm@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at
compile time. We thus need to add HAS_IOPORT as dependency for those
drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240410084201.1481930-2-schnelle@linux.ibm.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
In general it's preferable to avoid placing cpumasks on the stack, as
for large values of NR_CPUS these can consume significant amounts of
stack space and make stack overflows more likely.
Use cpumask_of() to avoid the need for a temporary cpumask on the stack
Signed-off-by: Dawei Li <set_pte_at@outlook.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/TYTP286MB3564B037A81DAAE1AC3A16F3CA062@TYTP286MB3564.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The always-running (from linux,wdt-gpio.yaml) is abused by the BD9576
watchdog driver. It's defined meaning is "the watchdog is always running
and can not be stopped". The BD9576 watchdog driver has implemented it
as "start watchdog when loading the module and prevent it from being
stopped".
Furthermore, the implementation does not set the WDOG_HW_RUNNING when
enabling the watchdog due to the "always-running" at module loading.
This will end up resulting a watchdog timeout if the device is not
opened.
The culprit was pointed out by Guenter, discussion can be found from
https://lore.kernel.org/lkml/4fa3a64b-60fb-4e5e-8785-0f14da37eea2@roeck-us.net/
Drop the invalid "always-running" handling.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: b237bcac55 ("wdt: Support wdt on ROHM BD9576MUF and BD9573MUF")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/ZhPAt76yaJMersXf@fedora
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Core in platform_driver_register() already sets the .owner, so driver
does not need to.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240327174638.519445-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
When the cpu5wdt module is removing, the origin code uses del_timer() to
de-activate the timer. If the timer handler is running, del_timer() could
not stop it and will return directly. If the port region is released by
release_region() and then the timer handler cpu5wdt_trigger() calls outb()
to write into the region that is released, the use-after-free bug will
happen.
Change del_timer() to timer_shutdown_sync() in order that the timer handler
could be finished before the port region is released.
Fixes: e09d9c3e9f ("watchdog: cpu5wdt.c: add missing del_timer call")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240324140444.119584-1-duoming@zju.edu.cn
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAmX20DQACgkQ+iyteGJfRsqIcgCeNaw/Nrzc2G4Lia/qjyYM2dUu
geMAn1g5h/ucw07k5p2Oe8qHDp1eC0wu
=PJHE
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-6.9-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- Remove usage of the deprecated ida_simple_xx() API
- Add kernel-doc for wdt_set_timeout()
- Add support for R-Car V4M, StarFive's JH8100 and sam9x7-wdt
- Fixes and small improvements
* tag 'linux-watchdog-6.9-rc1' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: intel-mid_wdt: Get platform data via dev_get_platdata()
watchdog: intel-mid_wdt: Don't use "proxy" headers
watchdog: intel-mid_wdt: Remove unused intel-mid.h
dt-bindings: watchdog: sama5d4-wdt: add compatible for sam9x7-wdt
dt-bindings: watchdog: sprd,sp9860-wdt: convert to YAML
dt-bindings: watchdog: starfive,jh7100-wdt: Add compatible for JH8100
watchdog: stm32_iwdg: initialize default timeout
dt-bindings: watchdog: arm,sp805: document the reset signal
watchdog: sp805_wdt: deassert the reset if available
watchdog/hpwdt: Support Suspend and Resume
dt-bindings: watchdog: renesas-wdt: Add support for R-Car V4M
watchdog: starfive: check watchdog status before enabling in system resume
watchdog: starfive: Check pm_runtime_enabled() before decrementing usage counter
watchdog: qcom: fine tune the max timeout value calculation
watchdog: Add kernel-doc for wdt_set_timeout()
watchdog: core: Remove usage of the deprecated ida_simple_xx() API
- Add support for Watchdog to ChromeOS Embedded Controller
- Add support for GPIOs to ChromeOS Embedded Controller
- Add supprt for Sound to MediaTek MT6357 CODEC
- New Functionality
- Add power-off functionality to Texas Instruments TWL series CODECs
- Fix-ups
- Device Tree binding adaptions/conversions/creation
- Use/convert to new/better APIs/helpers/MACROs instead of hand-rolling implementations
- Trivial; spelling, whitespace, clean-ups, etc
- Remove superfluous code and simplify overall
- Fix include lists; alphabetise, remove unused, explicitly add used
- Use dev_err_probe() to clean-up error paths
- Convert used cache type over to the Maple Tree in many instances
- Constify a bunch of static structs
- Refrain from over-riding resources provided via the firmware
- Bug Fixes
- Fix a clock related firmware bug on Dell XPS 9530 et al.
- Repair incorrect IRQ designations
- Increase buffer sizes to omit various snprintf compiler errors
- Ensure errors are handled properly
- Balance references and prevent resource leaks
- Rectify Power Key interrupt processing
- Fix Kconfig related build errors
- Correct a bunch of register start-up default values
-----BEGIN PGP SIGNATURE-----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=YeJS
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support:
- Add support for Watchdog to ChromeOS Embedded Controller
- Add support for GPIOs to ChromeOS Embedded Controller
- Add supprt for Sound to MediaTek MT6357 CODEC
New Functionality:
- Add power-off functionality to Texas Instruments TWL series CODECs
Fix-ups:
- Device Tree binding adaptions/conversions/creation
- Use/convert to new/better APIs/helpers/MACROs instead of
hand-rolling implementations
- Trivial; spelling, whitespace, clean-ups, etc
- Remove superfluous code and simplify overall
- Fix include lists; alphabetise, remove unused, explicitly add used
- Use dev_err_probe() to clean-up error paths
- Convert used cache type over to the Maple Tree in many instances
- Constify a bunch of static structs
- Refrain from over-riding resources provided via the firmware
Bug Fixes:
- Fix a clock related firmware bug on Dell XPS 9530 et al.
- Repair incorrect IRQ designations
- Increase buffer sizes to omit various snprintf compiler errors
- Ensure errors are handled properly
- Balance references and prevent resource leaks
- Rectify Power Key interrupt processing
- Fix Kconfig related build errors
- Correct a bunch of register start-up default values"
* tag 'mfd-next-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (65 commits)
mfd: cs42l43: Fix wrong GPIO_FN_SEL and SPI_CLK_CONFIG1 defaults
mfd: cs42l43: Fix wrong register defaults
mfd: mt6397-core: Register mt6357 sound codec
dt-bindings: mfd: syscon: Add ti,am62-usb-phy-ctrl compatible
dt-bindings: mfd: dlg,da9063: Make #interrupt-cells required
dt-bindings: mfd: Convert atmel-flexcom to json-schema
mfd: kempld-core: Don't replace resources provided by ACPI
mfd: cros_ec_dev: Add GPIO device if feature present on EC
dt-bindings: mfd: cros-ec: Add properties for GPIO controller
mfd: twl: Select MFD_CORE
mfd: core: Constify the struct device_type usage
mfd: rk8xx-core: Fix interrupt processing order for power key button
mfd: twl4030-power: Accept standard property for power controller
mfd: twl-core: Add power off implementation for twl603x
dt-bindings: mfd: ti,twl: Document system-power-controller
mfd: altera-sysmgr: Call of_node_put() only when of_parse_phandle() takes a ref
mfd: syscon: Remove extern from function prototypes
mfd: syscon: Call of_node_put() only when of_parse_phandle() takes a ref
mfd: mc13xxx: Use bitfield helpers
mfd: rc5t583: Convert to use maple tree register cache
...
Access to platform data via dev_get_platdata() getter to make code cleaner.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240305165306.1366823-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
intel-mid.h is providing some core parts of the South Complex PM,
which are usually are not used by individual drivers. In particular,
this driver doesn't use it, so simply remove the unused header.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240305165306.1366823-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The driver never sets a default timeout value, therefore it is
initialized to zero. When CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED is
enabled, the watchdog is started during probe. The kernel is supposed to
automatically ping the watchdog from this point until userspace takes
over, but this does not happen if the configured timeout is zero. A zero
timeout causes watchdog_need_worker() to return false, so the heartbeat
worker does not run and the system therefore resets soon after the
driver is probed.
This patch fixes this by setting an arbitrary non-zero default timeout.
The default could be read from the hardware instead, but I didn't see
any reason to add this complexity.
This has been tested on an STM32F746.
Fixes: 85fdc63fe2 ("drivers: watchdog: stm32_iwdg: set WDOG_HW_RUNNING at probe")
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240228182723.12855-1-ben.wolsieffer@hefring.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
According to the datasheet, the core has an WDOGRESn input signal that
needs to be deasserted before being operational. Implement it in the
driver.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240221-hisi-wdt-v3-1-9642613dc2e6@outlook.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
System resume will start and enable watchdog regardless of whether the
watchdog is enabled/disabled during a system suspend.
Add a check to the watchdog status and only start and enable the
watchdog if the watchdog status is running/active.
Signed-off-by: Sia Jee Heng <jeeheng.sia@starfivetech.com>
Signed-off-by: Ji Sheng Teoh <jisheng.teoh@starfivetech.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240130055118.1917086-1-jisheng.teoh@starfivetech.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
In the probe function, pm_runtime_put_sync() will fail on platform with
runtime PM disabled.
Check if runtime PM is enabled before calling pm_runtime_put_sync() to
fix it.
Fixes: db728ea9c7 ("drivers: watchdog: Add StarFive Watchdog driver")
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Signed-off-by: Ley Foon Tan <leyfoon.tan@starfivetech.com>
Signed-off-by: Ji Sheng Teoh <jisheng.teoh@starfivetech.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240119082722.1133024-1-jisheng.teoh@starfivetech.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
To determine the max_timeout value, the below calculation is used.
max_timeout = 0x10000000 / clk_rate
cat /sys/devices/platform/soc@0/b017000.watchdog/watchdog/watchdog0/max_timeout
8388
However, this is not valid for all the platforms. IPQ SoCs starting from
IPQ40xx and recent Snapdragron SoCs also has the bark and bite time field
length of 20bits, which can hold max up to 32 seconds if the clk_rate is
32KHz.
If the user tries to configure the timeout more than 32s, then the value
will be truncated and the actual value will not be reflected in the HW.
To avoid this, lets add a variable called max_tick_count in the device data,
which defines max counter value of the WDT controller. Using this, max-timeout
will be calculated in runtime for various WDT contorllers.
With this change, we get the proper max_timeout as below and restricts
the user from configuring the timeout higher than this.
cat /sys/devices/platform/soc@0/b017000.watchdog/watchdog/watchdog0/max_timeout
32
Signed-off-by: Kathiravan Thirumoorthy <quic_kathirav@quicinc.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240116-wdt-v2-1-501c7694c3f0@quicinc.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The wdt_set_timeout function lacked a complete kernel-doc
description. This patch adds missing parameter and return
value descriptions in accordance with kernel-doc standards.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Guenter Roeck <linux@roeckus.net>
Link: https://lore.kernel.org/r/20240206093857.62444-1-yang.lee@linux.alibaba.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
ida_alloc() and ida_free() should be preferred to the deprecated
ida_simple_get() and ida_simple_remove().
Note that the upper limit of ida_simple_get() is exclusive, but the one of
ida_alloc_range()/ida_alloc_max() is inclusive. So a -1 has been added when
needed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/bc5b82db59ccac69f2612ba104e2f5100401a862.1705009009.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Obtain the PMU regmap using the new API added to exynos-pmu driver rather
than syscon_regmap_lookup_by_phandle(). As this driver no longer depends
on mfd syscon remove that header and Kconfig dependency.
Tested-by: Alexey Klimov <alexey.klimov@linaro.org>
Tested-by: Sam Protsenko <semen.protsenko@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240220220613.797068-3-peter.griffin@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Embedded Controller (EC) present on Chromebook devices
can be used as a watchdog.
Implement a driver to support it.
Signed-off-by: Lukasz Majczak <lma@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240126095721.782782-3-lma@chromium.org
Signed-off-by: Lee Jones <lee@kernel.org>
Correct kernel-doc warnings as reported by kernel test robot:
mlx_wdt.c:56: warning: Function parameter or member 'wdt_type' not described in 'mlxreg_wdt'
mlx_wdt.c:56: warning: Excess struct member 'device' description in 'mlxreg_wdt'
mlx_wdt.c:56: warning: Excess struct member 'timeout' description in 'mlxreg_wdt'
mlx_wdt.c:56: warning: Excess struct member 'wd_type' description in 'mlxreg_wdt'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312171701.xNkzdgdi-lkp@intel.com/
Cc: Michael Shych <michaelsh@nvidia.com>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231218062659.26916-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
WDTCTRL bit 3 sets the mode choice for the clock input of IT8784/IT8786.
Some motherboards require this bit to be set to 1 (= PCICLK mode),
otherwise the watchdog functionality gets broken. The BIOS of those
motherboards sets WDTCTRL bit 3 already to 1.
Instead of setting all bits of WDTCTRL to 0 by writing 0x00 to it, keep
bit 3 of it unchanged for IT8784/IT8786 chips. In this way, bit 3 keeps
the status as set by the BIOS of the motherboard.
Watchdog tests have been successful with this patch with the following
systems:
IT8784: Thomas-Krenn LES plus v2 (YANLING YL-KBRL2 V2)
IT8786: Thomas-Krenn LES plus v3 (YANLING YL-CLU L2)
IT8786: Thomas-Krenn LES network 6L v2 (YANLING YL-CLU6L)
Link: https://lore.kernel.org/all/140b264d-341f-465b-8715-dacfe84b3f71@roeck-us.net/
Signed-off-by: Werner Fischer <devlists@wefi.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231213094525.11849-4-devlists@wefi.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This patch adds watchdog support for the ITE IT8659 watchdog.
IT8659 watchdog works in the same way as the other watchdogs supported
by it87_wdt.
Before this patch, IT8659 watchdog is not supported. After a modprobe,
dmesg reports:
it87_wdt: Unknown Chip found, Chip 8659 Revision 0007
With this patch, modprobe it87_wdt recognizes the watchdog as the dmesg
output shows:
it87_wdt: Chip IT8659 revision 7 initialized. timeout=60 sec (nowayout=0
testmode=0)
Watchdog tests on a YANLING YL-ALP3L2C-1235U system have been successful,
the watchdog works as expected with this patch.
Signed-off-by: Werner Fischer <devlists@wefi.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231213094525.11849-3-devlists@wefi.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Commit 893dc8b5c9 ("watchdog: it87: Drop support for resetting watchdog
though CIR and Game port") removed the try_gameport variable, and left
max_units setting redundant.
To clean up the code, this patch removes this redundant setting.
Signed-off-by: Werner Fischer <devlists@wefi.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231213094525.11849-2-devlists@wefi.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This patch fixes the following checkpatch.pl warning:
WARNING: Missing a blank line after declarations
Signed-off-by: Werner Fischer <devlists@wefi.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231213094525.11849-1-devlists@wefi.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Call runtime_pm_put*() if watchdog is not already started during probe and re
enable it in watchdog start as required.
On K3 SoCs, watchdogs and their corresponding CPUs are under same
power-domain, so if the reference count of unused watchdogs aren't
dropped, it will lead to CPU hotplug failures as Device Management
firmware won't allow to turn off the power-domain due to dangling
reference count.
Fixes: 2d63908bdb ("watchdog: Add K3 RTI watchdog support")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231213140110.938129-1-vigneshr@ti.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Add the necessary __acquires() and __releases() to the functions
that take and release the wdt lock to avoid the following sparse
warnings:
drivers/watchdog/starfive-wdt.c:204:13: warning: context imbalance in 'starfive_wdt_unlock' - wrong count at exit
drivers/watchdog/starfive-wdt.c:212:9: warning: context imbalance in 'starfive_wdt_lock' - unexpected unlock
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231122085118.177589-1-ben.dooks@codethink.co.uk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Add support for watchdog and reset generator unit of the MediaTek
MT7988 SoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/c0cf5f701801cce60470853fa15f1d9dced78c4f.1700504385.git.daniel@makrotopia.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Users report about the unexpected behavior for setting timeouts above
15 sec on Raspberry Pi. According to watchdog-api.rst the ioctl
WDIOC_SETTIMEOUT shouldn't fail because of hardware limitations.
But looking at the code shows that max_timeout based on the
register value PM_WDOG_TIME_SET, which is the maximum.
Since 664a39236e ("watchdog: Introduce hardware maximum heartbeat
in watchdog core") the watchdog core is able to handle this problem.
This fix has been tested with watchdog-test from selftests.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217374
Fixes: 664a39236e ("watchdog: Introduce hardware maximum heartbeat in watchdog core")
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231112173251.4827-1-wahrenst@gmx.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
ProLiants of vintage to have an iLO 5, no longer send watchdog NMI
as an IO CHECK. They are presented to hpwdt_pretimeout as NMI_UNKNOWN.
The preceding if statement rejects if !mynmi irrespective of value
of pretimeout making this if statement redundant.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231213215340.495734-3-jerry.hoemann@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Avoid unnecessary crashes by claiming only NMIs that are due to
ERROR signalling or generated by the hpwdt hardware device.
The code does this, but only for iLO5.
The intent was to preserve legacy, Gen9 and earlier, semantics of
using hpwdt for error containtment as hardware/firmware would signal
fatal IO errors as an NMI with the expectation of hpwdt crashing
the system. Howerver, these IO errors should be received by hpwdt
as an NMI_IO_CHECK. So the test is overly permissive and should
not be limited to only ilo5.
We need to enable this protection for future iLOs not matching the
current PCI IDs.
Fixes: 62290a5c19 ("watchdog: hpwdt: Claim NMIs generated by iLO5")
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231213215340.495734-2-jerry.hoemann@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231106154807.3866712-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231106154807.3866712-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231106154807.3866712-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
On today's platforms the benefit of platform_driver_probe() isn't that
relevant any more. It allows to drop some code after booting (or module
loading) for .probe() and discard the .remove() function completely if
the driver is built-in. This typically saves a few 100k.
The downside of platform_driver_probe() is that the driver cannot be
bound and unbound at runtime which is ancient and also slightly
complicates testing. There are also thoughts to deprecate
platform_driver_probe() because it adds some complexity in the driver
core for little gain. Also many drivers don't use it correctly. This
driver for example misses to mark the driver struct with __refdata which
is needed to suppress a (W=1) modpost warning:
WARNING: modpost: drivers/watchdog/txx9wdt: section mismatch in reference: txx9wdt_driver+0x4 (section: .data) -> txx9wdt_remove (section: .exit.text)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231106154807.3866712-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
On today's platforms the benefit of platform_driver_probe() isn't that
relevant any more. It allows to drop some code after booting (or module
loading) for .probe() and discard the .remove() function completely if
the driver is built-in. This typically saves a few 100k.
The downside of platform_driver_probe() is that the driver cannot be
bound and unbound at runtime which is ancient and also slightly
complicates testing. There are also thoughts to deprecate
platform_driver_probe() because it adds some complexity in the driver
core for little gain. Also many drivers don't use it correctly. This
driver for example misses to mark the driver struct with __refdata which
is needed to suppress a (W=1) modpost warning:
WARNING: modpost: drivers/watchdog/at91sam9_wdt: section mismatch in reference: at91wdt_driver+0x4 (section: .data) -> at91wdt_remove (section: .exit.text)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231106154807.3866712-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
When the new watchdog character device is registered, it becomes
available for opening. This creates a race where userspace may open the
device before the character device's owner is set. This results in an
imbalance in module_get calls as the cdev_get in cdev_open will not
increment the reference count on the watchdog driver module.
This causes problems when the watchdog character device is released as
the module loader's reference will also be released. This makes it
impossible to open the watchdog device later on as it now appears that
the module is being unloaded. The open will fail with -ENXIO from
chrdev_open.
The legacy watchdog device will fail with -EBUSY from the try_module_get
in watchdog_open because it's module owner is the watchdog core module
so it can still be opened but it will fail to get a refcount on the
underlying watchdog device driver.
Fixes: 72139dfa24 ("watchdog: Fix the race between the release of watchdog_core_data and cdev")
Signed-off-by: Curtis Klein <curtis.klein@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231205190522.55153-1-curtis.klein@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This patch adds the compatibles and drvdata for the Google
gs101 SoC found in Pixel 6, Pixel 6a & Pixel 6 pro phones.
Similar to Exynos850 it has two watchdog instances, one for
each cluster and has some control bits in PMU registers.
gs101 also has the dbgack_mask bit in wtcon register, so
we also enable QUIRK_HAS_DBGACK_BIT.
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231211162331.435900-13-peter.griffin@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Update the remaining QUIRK macros to use the BIT macro.
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20231211162331.435900-12-peter.griffin@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The WDT uses the CPU core signal DBGACK to determine whether the SoC
is running in debug mode or not. If the DBGACK signal is asserted and
DBGACK_MASK bit is enabled, then WDT output and interrupt is masked
(disabled).
Presence of the DBGACK_MASK bit is determined by adding a new
QUIRK_HAS_DBGACK_BIT quirk. Also update to use BIT macro to avoid
checkpatch --strict warnings.
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20231211162331.435900-11-peter.griffin@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=g+6E
-----END PGP SIGNATURE-----
Merge tag 'mips_6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- removed AR7 platform support
- cleanups and fixes
* tag 'mips_6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: AR7: remove platform
watchdog: ar7_wdt: remove driver to prepare for platform removal
vlynq: remove bus driver
mtd: parsers: ar7: remove support
serial: 8250: remove AR7 support
arch: mips: remove ReiserFS from defconfig
MIPS: lantiq: Remove unnecessary include of <linux/of_irq.h>
MIPS: lantiq: Fix pcibios_plat_dev_init() "no previous prototype" warning
MIPS: KVM: Fix a build warning about variable set but not used
MIPS: Remove dead code in relocate_new_kernel
mips: dts: ralink: mt7621: rename to GnuBee GB-PC1 and GnuBee GB-PC2
mips: dts: ralink: mt7621: define each reset as an item
mips: dts: ingenic: Remove unneeded probe-type properties
MIPS: loongson32: Remove dma.h and nand.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAmVL2nUACgkQ+iyteGJfRspY0gCgu/eCCZ1E/CU/xLQ7YtLQ7i7L
qtYAn07XudrdaCkbSwW6MiBsiCA33ae4
=NU1w
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-6.7-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- add support for Amlogic C3 and S4 SoCs
- add IT8613 ID
- add MSM8226 and MSM8974 compatibles
- other small fixes and improvements
* tag 'linux-watchdog-6.7-rc1' of git://www.linux-watchdog.org/linux-watchdog: (24 commits)
dt-bindings: watchdog: Add support for Amlogic C3 and S4 SoCs
watchdog: mlx-wdt: Parameter desctiption warning fix
watchdog: aspeed: Add support for aspeed,reset-mask DT property
dt-bindings: watchdog: aspeed-wdt: Add aspeed,reset-mask property
watchdog: apple: Deactivate on suspend
dt-bindings: watchdog: qcom-wdt: Add MSM8226 and MSM8974 compatibles
dt-bindings: watchdog: fsl-imx7ulp-wdt: Add 'fsl,ext-reset-output'
wdog: imx7ulp: Enable wdog int_en bit for watchdog any reset
drivers: watchdog: marvell_gti: Program the max_hw_heartbeat_ms
drivers: watchdog: marvell_gti: fix zero pretimeout handling
watchdog: marvell_gti: Replace of_platform.h with explicit includes
watchdog: imx_sc_wdt: continue if the wdog already enabled
watchdog: st_lpc: Use device_get_match_data()
watchdog: wdat_wdt: Add timeout value as a param in ping method
watchdog: gpio_wdt: Make use of device properties
sbsa_gwdt: Calculate timeout with 64-bit math
watchdog: ixp4xx: Make sure restart always works
watchdog: it87_wdt: add IT8613 ID
watchdog: marvell_gti_wdt: Fix error code in probe()
Watchdog: marvell_gti_wdt: Remove redundant dev_err_probe() for platform_get_irq()
...
This property allows the device-tree to specify how the Aspeed
watchdog timer's reset mask register(s) should be set, so that
peripherals can be individually exempted from (or opted in to) being
reset when the watchdog timer expires.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230922104231.1434-6-zev@bewilderbeest.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
